Sony | sony hcd-sd1 | User's Manual | Sony sony hcd-sd1 User's Manual

HCD-SD1
SERVICE MANUAL
AEP Model
UK Model
E Model
HCD-SD1 is the amplifier, CD and
tuner section in CMT-SD1.
Model Name Using Similar Mechanism
CD
SECTION
HCD-MD313
Mechanism Type
CDM13B-5BD19
Base Unit Type
BU-5BD19
Optical Pick-up Type
KSS-213B/K-N
SPECIFICATIONS
— Continued on next page —
COMPACT DISC RECEIVER
MICROFILM
–1–
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
This caution
label is located
inside the unit.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
MODEL IDENTIFICATION
– Specification Label –
MODEL NO. HCD-SD1
SAFETY-RELATED COMPONENT WARNING !!
Parts No.
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE
WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MODEL
AEP, UK model
SP, HK model
PARTS No.
4-212-711-0π
4-212-712-0π
• Abbreviation
HK : Hong Kong model
SP
: Singapore model
–2–
TABLE OF CONTENTS
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
1. SERVICING NOTE .......................................................... 4
2. GENERAL .......................................................................... 7
3. DISASSEMBLY
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
Loading Panel ....................................................................... 8
Glass ASSY ........................................................................... 8
Front Panel ........................................................................... 9
Main Board and Tuner Unit .................................................. 9
CD Mechanism Deck .......................................................... 10
Back Panel ......................................................................... 10
Disc Table .......................................................................... 11
Optical Pick-up ................................................................... 11
4. SERVICE MODE ............................................................. 12
5. TEST MODE ..................................................................... 13
6. ELECTRICAL ADJUSTMENTS ............................... 14
7. DIAGRAMS
7-1. Circuit Boards Location ...................................................... 16
7-2. Block Diagrams
• BD Section ....................................................................... 17
• Main Section .................................................................... 19
7-3. Schematic Diagram – BD Section – ................................... 23
7-4. Printed Wiring Board – BD Section – ................................. 25
7-5. Schematic Diagram – Main (1/2) Section – ........................ 27
7-6. Schematic Diagram – Main (2/2) Section – ........................ 29
7-7. Printed Wiring Board – Main Section – .............................. 31
7-8. Schematic Diagram – Sub Trans Section – ......................... 33
7-9. Printed Wiring Board – Sub Trans Section – ...................... 34
7-10. Schematic Diagram – Panel Section – ............................. 35
7-11. Printed Wiring Board – Panel Section – ........................... 37
7-12. Schematic Diagram – AMP Section – .............................. 39
7-13. Printed Wiring Board – AMP Section – ........................... 41
7-14. Schematic Diagram – Connector Section – ...................... 43
7-15. Printed Wiring Board – Connector Section – ................... 45
7-16. Schematic Diagram – REG Section – .............................. 47
7-17. Printed Wiring Board – REG Section – ............................ 49
7-18. IC Block Diagrams ........................................................... 51
7-19. IC Pin Functions ............................................................... 54
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
Carry out the “S curve check” in “CD section adjustment” and check
that the S curve waveform is output two times.
8. EXPLODED VIEWS
8-1.
8-2.
8-3.
8-4.
Front Panel Section ............................................................. 56
Chassis Section ................................................................... 57
Mechanism Deck Section (CDM13B-5BD19) ................... 58
Base Unit Section (BU-5BD19) .......................................... 59
9. ELECTRICAL PARTS LIST ........................................ 60
–3–
SECTION 1
SERVICING NOTE
OPENING THE DISC TRAY WHEN POWER IS OFF
2 Open the glass door, and pull out the loading panel.
1 Using a thin screwdriver, rotate the internal cam
in the arrow direction completely.
ATTACHING THE GLASS ASSEMBLY
• Attach according to steps 1 to 4.
2 Pull up the glass door,
in the arrow direction.
1
1
4 Screw (PTP 2.6x6)
3 Bracket (shaft)
(Bottom side)
–4–
When securing this part, position at the
center to allow some play. Open and close
the glass window several times, and check
that the parts do not touch each other.
POSITIONS FOR SERVICING THE CONNECTOR
BOARD, SUB-TRANS BOARD, CHEMI-CON BOARD,
AND AMP BOARD
1 Remove the four screws securing the upper cover, and remove
the upper cover.
2 Remove the loading panel. (Refer to SECTION 3 DISASSEMBLY.)
3 Remove the four screws A securing the MAIN board, five screws
B securing the rear panel, two flat cables (CN701, CN702),
and open the MAIN board as shown in the figure.
4 Remove the two screws C securing the heat sink, and remove
the AMP board and CHEMI-CON board.
5 Remove the two screws D securing the SUB-TRANS board
and four screws E securing the CONNECTOR board, and remove the SUB-TRANS board and CONNECTOR board.
6 Return the MAIN board to its original position.
7 Insulate these boards and the MAIN board with paper, etc., and
assemble the CONNECTOR board, SUB-TRANS board,
CHEMI-CON board, and AMP board on these boards.
D
C
AMP board
Heat sink
CHEMI-CON board
SUB-TRANS board
CONNECTOR board
B
B
E
MAIN board
Flat type wire (CN701)
A
A
Flat type wire (CN702)
Should be insulatable
with paper, etc.
–5–
POSITION FOR SERVICING THE CD MECHANISM
DECK
1 Remove the four screws securing the upper cover, and remove
the upper cover.
2 Remove the loading panel. (Refer to SECTION 3 DISASSEMBLY.)
3 Remove the four screws A securing the MAIN board, five screws
B of the rear panel, and flat cables (CN701, CN702), and remove the MAIN board.
4 Remove the two screws D securing the SUB-TRANS board,
and remove the SUB-TRANS board.
5 Remove the two screws F securing the REG board.
6 Remove the three screws G securing the CDM cover, and remove the CDM cover.
7 Remove the two screws H securing the CDM, move the CDM
backwards by about 5 mm horizontally, and then lift upwards.
8 Rotate the CDM in the counterclockwise direction by about 30˚
to remove.
9 Return the MAIN and SUB-TRANS boards to their original
positions.
D
SUB-TRANS board
B
B
F
MAIN board
G
CDM cover
Flat type wire (CN701)
A
A
Flat type wire (CN702)
H
–6–
SECTION 2
GENERAL
Front Panel
2
1
3
15
14
4
13
12
11
10
9
8
7
6
5
Location of Parts and Controls
1
2
3
4
5
1/u (Power) button
CD disc tray
§ button
VOLUME dial
±/)/TUNING + button
6
7
8
9
10
≠/0/TUNING – button
π button
fl button
TUNER/BAND button
FUNCTION button
11
12
13
14
15
DISPLAY button
PHONES jack
t indicator
u indicator
Display window
This section is extracted from
instruction manual.
–7–
SECTION 3
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
3-1. LOADING PANEL
1 Turn ON the power, and press the EJECT button to open the
tray.
2 Remove the loading panel in the arrow direction.
3 Press the EJECT button to close the tray.
• If the power cannot be turned ON, refer to “Opening the Disc
Tray When the Power is OFF” of “Service Note”, and open the
tray.
Loading panel
Power button
Eject button
3-2. GLASS ASSY
4
3
4
1 Screw (PTP2.6x6)
2 Bracket (shaft)
(Bottom side)
–8–
3-3. FRONT PANEL
4 Flat type wire (11core)
(CN702)
6 Front panel
3
2 Three claws
5 Flat type wire (13core)
(CN701)
1 Three screws
(BVTP3x8)
3-4. MAIN BOARD AND TUNER UNIT
1 Four screws
(BVTP3x8)
7 MAIN board and Tuner unit
6 Flat type wire
(19core) (CN705)
8 Connector (CN706)
5 Connector (CN351)
4 Flat type wire (19core)
(CN301)
3
–9–
2 Six screws
(BVTP3x8)
3-5. CD MECHANISM DECK
6 Three screws
(BVTP3x8)
7 Dust cover
9 CD mechanism deck
8 Two screws
(BVTP3x8)
3 Connector
(CN942)
5 REG board
1 Two screws
(BVTP3x8)
2 Connector
(CN945)
4 Connector
(CN994)
3-6. BACK PANEL
2 Four screws
(BVTT3X8)
7 Back panel
5 Connector
(CN901)
1 Six screws
(BVTP3X8)
3 Connector
(CN992)
6 Connector
(CN551)
8 PC board block
4 Connector
(CN991)
– 10 –
3-7. DISC TABLE
3 Holder (MG) assembly
1 Screw (BV3x8)
2 Screw (BV3x8)
4 Pull out the disc table.
3-8. OPTICAL PICK-UP
4 Remove the optical pickup in the arrow direction C.
C
3 Flat type wire (16 core)
(CNU101)
1 Move the claw
in the arrow A direction.
B
A
2 Remove the sled shaft in the
arrow direction B.
– 11 –
BD board
SECTION 4
SERVICE MODE
Key Check Mode for Complete Lighting of LED/Fluorescent Display Tube
• Perform this mode to analyze and check malfunctions such as display defects and when buttons do not work.
Procedure:
1. Press the 1/u button to turn on the power.
2. Press the DISPLAY button and ^ button together.
3. All LEDs and the fluorescent display tube will light up completely.
4. Pressing the FUNCTION button here will light the fluorescent display tube in the following order; Partial lighting 1 n Partial lighting
2 n Complete lighting n Partial lighting 1······
Turning the VOLUME dial will switch the lighting order of the LED.
To end without shifting to the key check mode, press the 1/u button to end.
5. Pressing the p button sets the key check mode.
6. During the key check mode, “KEY=0 JOG=0” will be displayed on the fluorescent display tube.
Pressing a button will increase the value of “KEY=”. However the value will not increase for buttons which have already been pressed
once.
Rotating the VOLUME knob in the clockwise direction increases the value of “JOG=” in the order of 1, 2, 3.... and rotating in the
counterclockwise direction decreases in order of 10, 9, and 8.
7. To end the check mode, press all buttons (8 buttons). “KEY-OK” will be displayed.
Then press any button, and disconnect the power cord from the outlet.
Checking the Sub-Clock
• Perform this mode to check clock operations.
Procedure:
1. Connect an oscilloscope and frequency counter between the pin (TP791) and ground of IC701 of the MAIN board.
2. Press the § and 1/u buttons together to display “91P = 32.768k” on the fluorescent display tube.
3. Check that the signal on the oscilloscope becomes a 32 kHz rectangular waveform and the reading of the frequency counter becomes
32.768 kHz.
4. Press the 1/u button to end.
Sled Servo Mode
• In this mode, the CD sled motor can be operated freely.
Execute it when cleaning the pick-up.
Round holes can be seen on the topmost board when the case is opened. Move the pick-up and clean off the dirt in these round holes using
a cotton swab.
Procedure:
1. Press the DISPLAY and § buttons with the power of the unit OFF.
2. When the sled servo is set, “MANUAL” is displayed on the fluorescent display tube.
3. Pressing the +/TUNING/) button when the CD is in the stop state moves the pick-up to the outer track. Pressing the =/
TUNING/0 button moves it to the inner track.
4. To end this mode, perform the following steps.
1) Move the If not, the disc cannot be removed.
2) Press the DISPLAY and § buttons together.
Note:
• When ending this mode, be sure to move the pick-up to the innermost circumference. If not, the disc cannot be removed.
• Do not move the sled motor more than required as this will damage the gears.
Round holes for cleaning
Initializing (Forced Reset)
• Perform this mode when resetting the unit or when returning the unit to the customer.
• The preset frequency of the tuner, etc. will be the settings at shipment.
Procedure:
While pressing the 1/u button, insert the power cord into the outlet.
– 12 –
SECTION 5
TEST MODE
AGING MODE
This unit is equipped with an aging mode.
Use this mode for analyzing defects and for checks after completing repairs.
After repairs, perform aging 100 times and check that the unit is normal.
The aging mode is executed in the following sequence.
The aging mode will continue as long as the unit is normal.
If the unit becomes abnormal, it will display the state and number of cycles, and operations will stop. (Refer to Table 1.)
Sequence of Aging Mode:
Start
Sets the CD function and reads the CD TOC.
CD TOC OK?
NO
Message 1
YES
Pauses first song.
NO
OK?
Message 2
YES
Last song search paused state
NO
OK?
Message 3
YES
Starts last song playback
OK?
NO
Message 4
YES
End playback?
NO
YES
Is CD playing?
OK
NG
Message 4
Opens the CD tray
OK?
NO
Message 5
YES
Closes the CD tray
OK?
NO
Message 6
YES
Power OFF
Display of number of aging cycles
Power ON
Procedure:
1. Press the DISPLAY button and =/TUNING/0 button together.
2. To end aging, press the u button and end.
Table-1 Messages and Main Reasons for Stop of Aging
No
1
Error Messages
CD No Disc NG
Details of Error
Cannot read CD TOC.
2
CD Pause NG
3
CD Search NG
Cannot set CD pause in
CD synchro mode.
Cannot search last track on CD.
4
CD Play NG
Cannot play last track on CD.
5
6
CD Open NG
CD Close NG
Cannot open CD tray.
Cannot close CD tray.
– 13 –
Main Causes
Optical defect, spindle defect (including motor), cannot read
Q data, disc defect (scratches, etc.), bad focus, bad GFS, etc.
Disc defect (scratches, etc.), cannot read Q data, etc.
Optical defect, sled, tracking defect (including motor), cannot
read Q data, disc defect (scratches, etc.).
Optical defect, cannot read Q data, disc defect (scratches, etc.),
etc.
LOAD OUT SW defect
LOAD IN SW defect
SECTION 6
ELECTRICAL ADJUSTMENTS
S Curve Check
CD SECTION
Note:
1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10MΩ impedance.
4. Clean the object lens by an applicator with lens cleaning liquid
when the signal level is low than specified value with the following checks.
5. Adjust the focus bias adjustment when optical block is replaced.
Focus Bias Adjustment
Perform this adjustment when the optical pick-up has been replaced
or repaired.
oscilloscope
BD (CD) board
TP (RF)
TP (VC)
oscilloscope
BD (CD) board
+
–
TP (FEO)
TP (VC)
Procedure :
1. Connect oscilloscope to test point TP (FEO).
2. Connect between test point TP (FOK) and Ground by lead wire.
3. Turn Power switch on.
4. Put disc (YEDS-18) in and turned Power switch on again and
actuate the focus search. (actuate the focus search when disc
table is moving in and out.)
5. Check the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within 2.4 ± 0.7
Vp-p.
+
–
S-curve waveform
symmetry
Procedure:
1. Connect oscilloscope to test point TP (RF).
2. Turned Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Adjust RV101 so that the waveform is clear.
(Clear RF signal waveform means that the shape “◊” can be
clearly distinguished at the center of the waveform.)
5. After adjustment, check the RF signal level.
• RF signal
VOLT/DIV: 200 mV
TIME/DIV: 500 nS
A
within 2.4 ± 0.7 Vp-p
B
6. After check, remove the lead wire connected in step 2.
Note: • Try to measure several times to make sure than the ratio of
A : B or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the brightness to obtain best waveform.
RF Level Check
oscilloscope
level : 1.3 ± 0.3 Vp-p
BD (CD) board
TP (RF)
TP (VC)
+
–
Procedure :
1. Connect oscilloscope to test point TP (RF) on BD board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Confirm that oscilloscope waveform is clear and check RF signal level is correct or not.
Note: Clear RF signal waveform means that the shape “◊” can be
clearly distinguished at the center of the waveform.
• RF signal
VOLT/DIV: 200 mV
TIME/DIV: 500 nS
level : 1.3 ± 0.3 Vp-p
– 14 –
E-F Balance (1 Track Jump) Check
(Without remote commander)
Adjustment Location:
[BD (CD) BOARD] — Component Side —
oscilloscope
RF
BD (CD) board
+
–
RV101
IC101
TEI
RV103
Procedure :
1. Connect oscilloscpe to test point TP (TEO) on BD board.
2. Turn Power switch on.
3. Put disc (YEDS-18) in to play the number five track.
4. Press the “P (Pause)” button. (Becomes the 1 track jump mode)
5. Confirm that the oscilloscope waveform is symmetrical on the
top and bottom in relation to 0Vdc, and check this level.
TEO
VC
FEO
IC102
TP (TEO)
TP (VC)
FOK
(Focus Bias Adjust)
FEI
RV102
1 track jump waveform
IC104
PCK
A
0V
GND
B
LEVEL : 300 ± 100 mVp-p
Specified level: •
A–B
x 100 = less than ± 7%
2 (A + B)
• A + B = 300 ± 100 mVp-p
Focus/Tracking Gain Adjustment (RV102, RV103)
This gain has a margin, so even if it is slightly off.
There is no problem.
Therfore, do not perform this adjustment.
Please note that it should be fixed to mechanical center position
when you moved and do not know original position.
– 15 –
SECTION 7
DIAGRAMS
7-1. CIRCUIT BOARDS LOCATION
TRANS board
MAIN board
PANEL-SW board
SUB-TRANS board
BD board
LOADING board
AMP board
REG board
CHEMI-CON board
PANEL board
HP board
CONNECTOR board
VOLUME board
– 16 –
HCD-SD1
7-2. BLOCK DIAGRAMS
– BD SECTION –
OPTICAL PICK-UP
(KSS-213B)
34
RV102
FOCUS
GAIN
RV101
FOCUS
BIAS
2 FEI
1 FEO
42 TEO
FE-O
FE-M
TA-M
TAO
44 TEI
RV103
TRACKING
GAIN
PD
+5V
FE BIAS 37
56 57 59 3 1 64
63 51 52 53
43 46 47 49
50
39
26 28 27
6
7
12
13
D OUT
LASER
DIODE
CLK
DATA
XRST
SCOR
SENS
SQCK
SQSO
DF LAT
XLAT
FOCUS SW
FOK 25
34 PHD
FOCUS SW
Q103
FGD 4
XRST
22
7
FOCUS
COIL
TRACKING
COIL
XRST
T+
18
17
T–
2-AXIS
DEVICE
F–
F+
TRACKING
COIL DRIVE
MOTOR
DRIVER
IC351
19
TRACKING/FOCUS
COIL DRIVE
IC102 (1/2)
12
11
FOCUS
COIL DRIVE
9
M904 (CD)
LOADING
MOTOR
M102
SLED MOTOR
M
M101
SPINDLE
MOTOR
M
2
DRIVE
5
LOAD-OUT
10
DRIVE
6
LOAD-IN
M
SLED
SERVO
IC101 (2/2)
SLED/SPINDLE
MOTOR DRIVE
IC102 (2/2)
26
•
27
SLED MOTOR
DRIVE
25
1
•
2
SPINDLE MOTOR
DRIVE
4
16 SLO
SL+ 14
OUT-SW
S291
(LOAD OUT)
IN-SW
S292
(LOAD IN)
09
• SIGNAL PATH
: CD
: Digital out
– 17 –
A
MAIN
SECTION
(Page 19)
DATA 21
XLT 20
CLK 19
33 LD
MAIN
SECTION
(Page 19)
S101
(LIMIT)
LD
LD DRIVE
Q101, 102
A
CD LOUT
ROUT 13
DATA
MLAT
CLOK
B
F
DIGITAL SIGNAL PROCESSOR
IC103
55 CNIN
54 SEIN
C.OUT 23
SENS 24
DIGITAL FILTER
D/A CONVERTER
IC104
LOUT 16
D OUT
C
38 F
39 E
2 DATA
1 LRCK
3 BCLK
PCMD 21
LRCK 20
BCLK 22
XRST
C
14 RF
RFO 31
RFI 30
SCOR
SQSO
SQCK
SENS
B
D
35 PD1
36 PD2
DATA
XLAT
CLOK
D
SPOD
A
5•6
DATAO
XLTO
CLKO
MDP
FOK
XLON
1
4
2
5
10
6
CKO
E
A
4
XTI
•
XTO
TRACKING/FOCUS SERVO,
RF AMP
IC101 (1/2)
B+
K
XTAI
DETECTOR
X101
22.5792 MHz
– 18 –
A
MAIN
SECTION
(Page 19)
HCD-SD1
– MAIN SECTION –
ANTENNA
SOUND PROCESSOR
IC101(1/2)
TUNER
UNIT
TUNER
L-OUT
AM
R-OUT
STEREO
BS/CS
R-CH
MD
ST
CD
TUN
TUNED
MUT
MUTING
DO
DO
CL
CL
DI
DI
CE
CE
FM-DET-OUT
FM
75Ω
5
15
BASS/
TREBLE
AMP
• VOLUME
6
7
R-CH
DEFB SW
Q121
8
16
18
27
DBFB
25
AMP
10
R-CH
+
R-CH
–
8
–
R-CH
+8dB AMP
IC103
35
R-CH
3
1
5
7
MUTE
Q505
J101(2/2)
L
MUTE
Q111
R-CH
L
R
+
RELAY SW
Q502,503
RELAY DRIVE
Q504
FAN-DRIVE
Q551–553
R-CH
FAN
RELAY SW
Q501
R-CH
J667
L
R-CH
SWITCH
IC102
J102
(1/2)
L
BS
12
14
CS/BS IN
SIRCS
IC602
L
2
IN
R-CH R-CH
R
TC-MUT 99
MUTE SW
Q183
MD-MUT 98
MUTE SW
Q182
13
R-CH
R
MUTE
Q112
MASTER CONTROL
IC701
15
DAT
CLK
LAT
R-CH
1
ST
9 10 11
TUN
DO
DI
CL
CE
MUT
SWITCH
Q103
90
65
66
67
SIRCS
SDATA
SCLOCK
82
83
84
85
86
87
88
STEREO
TUNED
ST.IDATA
ST.ODATA
ST.CLOCK
ST.LATCH
ST.MUTE
SLAT1
100 V/T
RDS DECODER
IC451
4 IN
38
37
36
35
INT 16
DATA 2
FL.RST
FL.LAT
FL.SLK
FL.DAT
14
20 RDS.CLK
X601
4.3 MHz
21 RDS.DAT
13
FLUORESCENT INDICATOR TUBE
FL601
CD
LOUT
MUTE2 69
A
5 – 50
CS
RST
DAT
CLK
56 VFL
G12
BUFFER
Q601
51
63 62 61 60
DISPLAY DRIVER
IC601
CD SECTION
(Page 18)
SCOR
SQSO
SQCK
FOCUS SW
SENS
CLK
DAT
DF-LAT
XLAT
XRST
IN SW
OUT SW
LOAD IN
LOAD OUT
22
43
45
52
53
57
58
59
60
63
49
50
61
62
D OUT
– 19 –
SCOR
SQSI
SQCK
FSW
SENS
CD-CLK
CD-DATA
DF-LAT
DSP-LAT
BD.RESET
IN SW
OUT SW
LOAD IN
LOAD OUT
TAPE
OUT
PHONES
CN781
DAT
HLP
CLK
MUTE SW
Q181
SP RELAY SW 76
1
2
5
DOUT
HPSW 31
ON/XSRBY 81
FLDISP SW 75
SWITCH
Q792
I 2 C.DAT 55
SWITCH
Q791
I2 C.CLOCK 56
6 SY
LY 7
3 SX
LX 2
I 2 C BUS
EXTENDER
IC791
S621-625,631-634
KEY2 26
T991
MAIN
TRANSFORMAER
HLP
SWITCH
Q793
HELP 51
KEY BOARD
SWITCH
DAT
CLK
±B
A±7.5VREG
Q941, 946
A±7.5VREG
D±5V
3 D+5VREG 1
IC921
M+7V
3
AC IN
RECT
D971
RY901
STANDBY RELAY
RECT
D941-944
AC OUTLET
CN904
RECTIFIER
D921,922
KEY1 25
ENCODERB 19
ENCODERA 18
XT1 14
X2 11
X1 10
2
1
VOLUME
S691
X701
5MHz
t
TIMER:RED
D605
M+7VREG
1
IC922
CDD+5V SW
Q942
CDD+5V
X702
32KHz
TIMER LED 73
ON LED 72
STBY LED 70
ST12V
u
ON:GREEN
STANDBY:RED
D606
ST 12V OUT
Q951,952
STBY+5.6V
RECTIFIER
Q951,953
3
VG
LIGHT 64
AC CUT
D601-604
SWITCH
Q752
D601
)/±
D602
D603 D604
fl
0/≠ π
VG SWITCH
Q966
8
RESET 15
PANEL SW
2
BD POWER
1
SYSTEM
CONTROL
IC311
SWITCH
Q753
MUTE1 68
XT2 13
VF1
VF0
R
R-CH
SPEAKER
INPEDANCE
6-16Ω
D881
MD
R OUT
R-CH
R-CH
J102(2/2)
R
–VG
TMB11
3
R-CH
IN
TAPE
9
MUTE
Q141
+
–
R-CH
L
MD
SPEAKER RELAY
RY501
28
LAT
20 LATCH
DAT
21 DATA
CLK
22 CLOCK
BUFFER
Q450
POWER AMP
IC801
4
39
38
37
36
R-CH
J101
(1/2)
SOUND PROCESSOR
IC101(2/2)
RESET
Q751
3
RESET
IC951
D752
D751
TO IC701 VDD
PANEL SW
S699
SWITCH
Q943
VG SW
Q964
1
RECT
D901-904
UG REG
Q961
RECT
D961-964
VF1
VF0
STBY+5.6V
1
STBY+5.6V REG
IC901
T991
SUB
TRANSFORMER
VF SW
Q962,963
• R ch is same as L ch
• SIGNAL PATH
: FM
BS
:BS/CS
: PB
: REC
: CD
: Digital out
: TAPE
VF SWITCH
Q965
+
C759 BACK UP
– 20 –
DIGITAL
OPTICAL
HCD-SD1
WAVEFORMS
– BD SECTION –
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed
in each block.)
– MAIN SECTION –
1
1
1.3 ± 0.3 Vp-p
4.3 Vp-p
For schematic diagrams.
Note:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
¢
•
: internal component.
• 2 : nonflammable resistor.
• 1 : fusible resistor.
• C : panel designation.
5 MHz
IC101 #¡ (RFO) (PLAY Mode)
500 mV/DIV, 500 ns/DIV
IC701 !¡ (XI)
2
2
Approx.
100 mVp-p
2.6 Vp-p
32 kHz
IC101 $¢ (TEI) (PLAY Mode)
50 mV/DIV, 1 µs/DIV
Note: The components identified by mark ! or dotted line
with mark ! are critical for safety.
Replace only with part number specified.
IC701 !¢ (XI)
3
Approx.
150 mVp-p
S : B+ Line.
T : B– Line.
H : adjustment for repair.
Voltages and waveforms are dc with respect to ground in
service mode.
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
•
•
•
•
IC101 2 (FEI) (PLAY Mode)
50 mV/DIV, 1 µs/DIV
4
2.6 Vp-p
7.6 µs
IC103 3 (MDP) (PLAY Mode)
5
5.1 Vp-p
Signal path.
F : FM
E : PB (MD)
m : PB (TAPE)
n : REC
J : CD
c : digital out
• Abbreviation
SP
: Singapore model.
HK
: Hong Kong model.
136 µs
IC103 @• (RFCK)
6
5.3 Vp-p
14 ns
IC103 @∞ (XPCK)
7
For printed wiring boards.
Note:
• X : parts extracted from the component side
•
p
: parts mounted on the conductor side.
®
: Through hole.
•
¢
•
: internal component.
• b : Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
5 Vp-p
474 ns
IC103 @™ (BCLK)
8
5.1 Vp-p
Parts on the pattern face side seen from the
pattern face are indicated.
Parts on the parts face side seen from the
parts face are indicated.
22.8 µs
IC103 @º (LRCK)
9
• Indication of transistor
4.6 Vp-p
C
Q
B E
These are omitted
16.9344 MHz
BC E
IC104 6 (XTO)
These are omitted
– 21 –
– 22 –
HCD-SD1
7-3. SCHEMATIC DIAGRAM – BD SECTION –
• See page 22 for Waveforms.
• See page 51 for IC Block Diagrams.
(Page 29)
Note on Schematic Diagram:
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : Stop
(
) : CD (PLAY)
*
: Can not be measured.
– 23 –
– 24 –
HCD-SD1
7-4. PRINTED WIRING BOARD – BD SECTION –
• See page 16 for Circuit Boards Location.
(Page 32)
OPTICAL PICK-UP
BLOCK
KSS-213BA/S-N
• Semiconductor
Location
• Semiconductor
Location
Ref. No.
Location
Ref. No.
Location
IC103
C-1
Q101
Q103
B-3
C-3
IC101
IC102
IC104
B-1
B-1
C-3
Q102
B-1
– 25 –
– 26 –
HCD-SD1
7-5. SCHEMATIC DIAGRAM – MAIN (1/2) SECTION –
• See page 22 for Waveforms.
• See page 31 for Printed Wiring Board.
(Page 39)
(Page
29)
(Page
29)
– 27 –
– 28 –
HCD-SD1
7-6. SCHEMATIC DIAGRAM – MAIN (2/2) SECTION –
• See page 22 for Waveforms.
• See page 31 for Printed Wiring Board.
• See page 53 for IC Block Diagrams.
• See page 54 for IC Pin Functions.
(Page 24)
(Page 43)
(Page 43)
(Page 36)
(Page
28)
(Page
28)
(Page 35)
(Page 48)
(Page 48)
– 29 –
– 30 –
HCD-SD1
7-7. PRINTED WIRING BOARD – MAIN SECTION –
• See page 16 for Circuit Boards Location.
(Page 41)
(Page 45)
(Page 26)
(Page 46)
• Semiconductor
Location
Ref. No.
Location
D351
D751
D752
D753
D755
D791
D792
D793
A-6
G-5
G-5
G-6
G-6
B-5
B-5
B-5
IC101
IC102
IC103
IC351
IC701
IC791
IC951
C-3
D-2
A-1
A-5
C-6
B-6
G-6
Q103
Q111
Q112
Q121
Q141
Q181
Q182
Q183
Q211
Q212
Q222
Q241
Q751
Q752
Q753
Q781
Q782
Q783
Q791
Q792
Q793
D-2
B-1
C-1
D-4
C-4
D-4
D-4
D-4
B-1
C-1
B-3
B-4
G-7
B-7
C-6
F-8
F-8
F-8
B-6
B-6
C-6
AEP, UK
(Page 37)
R
OUT
L
R
IN
L
R
OUT
L
R
IN
*1
L
R
IN
L
*1
AEP, UK SP, HK
JW734
JW735
R735
: MOUNT
: NO MOUNT
X601
AEP, UK
(Page 38)
(Page 50)
– 31 –
– 32 –
(Page 50)
HCD-SD1
7-9. PRINTED WIRING BOARD – SUB SECTION –
• See page 16 for Circuit Boards Location.
7-8. SCHEMATIC DIAGRAM – SUB SECTION –
(Page 49)
(Page 47)
DTC114ESA
11EQS04
11EQS04
11EQS04
(Page 43)
DTA114ESA-TP
11EQS04
11ES2-NTA2B
11ES2NTA2B
DTA114ESA-TP
11ES2NTA2B
11ES2-NTA2B
(Page 45)
• Semiconductor Location
– 33 –
Ref. No.
Location
Ref. No.
Location
D901
D902
D903
D904
D905
D906
D961
D962
D963
D964
D965
B-2
B-1
B-1
B-1
C-2
B-3
B-2
B-2
B-2
B-2
C-2
D966
C-1
IC901
C-2
Q901
Q961
Q962
Q963
Q964
Q965
Q966
B-3
C-2
B-3
C-3
C-3
C-2
C-2
– 34 –
HCD-SD1
7-10. SCHEMATIC DIAGRAM – PANEL SECTION –
(Page 30)
(Page 30)
– 35 –
– 36 –
HCD-SD1
7-11. PRINTED WIRING BOARD – PANEL SECTION –
• See page 16 for Circuit Boards Location.
(Page 32)
(Page 32)
E
• Semiconductor
Location
Ref. No.
Location
D601
D602
D603
D604
D605
D606
C-3
C-3
C-4
C-5
B-7
B-7
IC601
IC602
B-5
B-2
Q601
C-3
AEP, UK
– 37 –
– 38 –
HCD-SD1
7-12. SCHEMATIC DIAGRAM – AMP SECTION –
(Page 47, 48)
(Page 43)
(Page 28)
– 39 –
– 40 –
HCD-SD1
7-13. PRINTED WIRING BOARD – AMP SECTION –
• See page 16 for Circuit Boards Location.
• Semiconductor
Location
(Page 50)
(Page 31)
(Page 45)
– 41 –
– 42 –
Ref. No.
Location
D553
D554
D971
D972
A-5
A-5
A-5
A-5
Q505
Q551
Q552
Q553
B-4
A-5
A-5
A-4
HCD-SD1
7-14. SCHEMATIC DIAGRAM – CONNECTOR SECTION –
(Page 30)
(Page 29)
(Page 40)
(Page 33)
– 43 –
– 44 –
HCD-SD1
7-15. PRINTED WIRING BOARD – CONNECTOR SECTION –
• See page 16 for Circuit Boards Location.
(Page 31, 32)
• Semiconductor
Location
Ref. No.
Location
D501
D556
D557
D881
B-3
B-3
C-3
D-2
IC311
B-5
Q501
Q502
Q503
Q504
B-2
B-2
B-3
B-3
(Page 34)
DIGITAL
OPTICAL
CD AUX
SPEAKER
INPEDANCE
AEP, UK
(Page 42)
SYSTEM
CONTROL
LOADING BOARD
S292
(LOAD IN)
S291
(LOAD OUT)
CN291
5
M
M904
(LOADING
MOTOR)
4
3
(Page 32)
2
1
1-634-461-
– 45 –
– 46 –
11
(11)
HCD-SD1
7-16. SCHEMATIC DIAGRAM – REG SECTION –
(Page 40)
(Page 29)
(Page 29)
(Page 33)
– 47 –
– 48 –
HCD-SD1
7-17. PRINTED WIRING BOARD – REG SECTION –
• See page 16 for Circuit Boards Location.
AC
OUTLET
MDS-SD1
ONLY
UNSWITCHED
200W MAX
NOT REPLACEABLE:
BUILT IN TRANSFORMER
(Page 32)
(Page 32)
(Page 34)
(Page 42)
• Semiconductor
Location
– 49 –
– 50 –
Ref. No.
Location
D921
D922
D941
D942
D943
D944
D945
D946
D952
A-4
A-4
A-4
A-4
A-4
A-4
B-2
B-1
B-1
IC921
IC922
B-3
B-3
Q941
Q942
Q943
Q951
Q952
B-2
C-2
C-2
A-1
B-1
HCD-SD1
PHD2
PHD1
PHD
LD
RF M
RF O
RF I
CP
CB
CC1
CC2
FOK
VCC
36
35
34
33
32
31
30
29
28
27
26
25
15 OP–
16 OP+
17 OUT3A
18 OUT3B
VCC
DRIVE
BUFFER
DRIVE
BUFFER
19 IN3A
20 IN3B
21 VCC
22 VCC
23 VC
24 IN4B
IC101 CXA1782BQ
25 IN4A
27 OUT4A
28 GND
• BD section
26 OUT4B
IC102 BA6397FP
7-18. IC BLOCK DIAGRAMS
DRIVE
BUFFER
–
+
+
+
THERMAL
SHUT DOWN
–
+
LEVELS
DRIVER MUTE
MIRR
RF IV AMP1
IIL
24 SENS
TTL
23 C. OUT
LEVEL
SHIFT
+
–
FOK
+
+
–
–
–
+
–
REGULATOR
+
APC
–
+
DFCT
–
DRIVE
BUFFER
DRIVE
BUFFER
DRIVE
BUFFER
• ADDRESS DECODER
FE AMP
• OUTPUT DECODER
IIL
19 CLK
IC103 CXD2507AQ
+
–
XLAT
CLOK
SEIN
CNIN
DATO
XLTO
VDD
PS1-4
CLKO
TM1-7
SPOA
TG1-2
64 63 62 61 60 59 58 57 56 55 54 53 52
18 VCC
FZC COMP
+
E 39
FS1-4
BAL1-3
SPOB
TOG1-3
SPOC
XLON
+
–
F IV AMP
SPOD
–
+
• TRACKING
HPF COMP
MDS 4
• ISET
• PHASE
COMPENSATION
LPF COMP
17 ISET
–
TM6
TG1
FILI 8
+
–
16 SL 0
TOG3
• FCS PHASE
COMPENSATION
TZC COMP
LPFI 43
FS1
TM7
ATSC
FS2
45 EXCK
44 SBSO
43 SCOR
42 VSS
3
41 WFCK
ASYMMETRY
CORRECTOR
40 EMPH
D/A
INTERFACE
5
RF 14
BIAS 15
DIGITAL
OUT
39 DOUT
38 C4M
6
16K
RAM
ASYO 17
ASYE 18
ERROR
CORRECTOR
3
37 FSTT
36 XTSL
35 XTAO
34 XTAI
33 MNTO
• F SET
+
47 SQCK
EFM
DEMODULATOR
DIGITAL
PLL
WDCK 19
TG2
DFCT
–
–
13 TA O
–
TDFCT 47
AVSS 11
CLTV 12
48 MUTE
DIGITAL
CLV
46 SQSO
ASYI 16
+
TM1
TZC 46
FS4
+
TG2
FSET
TA M
VDD
GFS
MNT1
TGU
MNT3
SRCH
– 51 –
XROF
12
RFCK
11
CZPO
10
XPCK
9
XUGF
8
GTOP
7
BCLK
6
PCMD
5
FE M
FDFCT
4
FE O
3
FLB
2
FGD
1
FEI
20 21 22 23 24 25 26 27 28 29 30 31 32
FEO
VC 48
14 SL P
TM2
DFCT
• WINDOW COMP
PCO 9
VSS 10
AVDD 13
TM3
TEI 44
ATSC 45
15 SL M
TM4
–
SUB CODE
PROCESSOR
4
LRCK
TOG2
TOG1
+
TM5
+
CPU
INTERFACE
14
51 DATA
50 XRST
49 SENS
5
LOCK 5
TEST 6
FILO 7
VEE 41
TEO 42
SERVO AUTO
SEQUENCER
FOK 1
MON 2
MDP 3
CLOCK
GENERATOR
+
–
BAL3
BAL2
BAL1
TE AMP
+
–
–
–
+
E IV AMP
EI 40
– 52 –
OP-OUT 14
GND 13
OUT2B 12
OUT2A 11
9
IN2A
XRST
REG 0
20 XLT
IIL
–
+
TR-B
• INPUT SHIFT RESISTOR
IN1B
• IIL DATA RESISTOR
TTL
IN1A
21 DATA
FE BIAS 37
IN2B 10
8
GND
7
6
5
2
OUT1B
3
1
OUT1A
+
TTL
RF IV AMP2
F 38
DRIVE
BUFFER
22 XRST
4
–
+
LEVEL
SHIFT
–
–
+
–
–
+
LEVEL
SHIFT
LEVEL
SHIFT
DRIVE
BUFFER
IC104 PCM1710U-R
LRCIN 1
28 ML/DSD
INPUT
INTERFACE
DIN 2
DIGITAL
FILTER
27 MC/DM2
MODE
CONTROL
BCKIN 3
CLKO
26 MD/DM1
TIMING
CONTROL
4
25 MUTE
XTI 5
24 MODE
XTO 6
23 CKSL
NOISE
SHAPER
DGND 7
22 DGND
VDD 8
21 VDD
5-LEVEL DAC
RIGHT
5-LEVEL DAC
LEFT
LOW-PASS FILTER
RIGHT
LOW-PASS FILTER
LEFT
VCC2R 9
GND2R 10
20 VCC2L
19 GND2L
EXT1R 11
18 EXT1L
3-STAGE AMP
LEFT
3-STAGE AMP
RIGHT
EXT2R 12
17 EXT2L
VOUTR 13
16 VOUTL
15 VCC1
GND1 14
– MAIN Section –
IC351 LB1641
T.S.D
O.C.P
MOTOR
DRIVE
MOTOR
DRIVE
FWD.IN
CLAMP
7
8
9
10
MOTOR
DRIVE
NOISE
FILTER
6
NOISE
FILTER
MOTOR
DRIVE
5
4
VCC 2
3
VCC 1
2
REV.IN
1
GND
FWD/REV/STOP
CONTROL LOGIC
VCC
NC
NC
IC791 P82B715TD.118
8
1
5
SDA
6
BUFFER
7 LDA
SCL
3
BUFFER
2
LCL
GND
4
– 53 –
7-19. IC PIN FUNCTIONS
• IC701 System Control (µPD780018AYGF-015-3BA) (MAIN Board)
Pin No.
1
Pin Name
BD POWER
2
PANEL SW
3 to 7
8
I/O
O
I
Function
CD power control pin, “H”:CD POWER ON
Front cover open/close switch, “H”:Open glass door, “L”:Close glass door
–
I
Not used
AC.CUT
I
AC power connection signal, “L”:Power is disconnected
9
VPP
–
Normally connected to the ground pin
10
X2
O
Main system clock output pin (5 MHz)
11
X1
I
Main system clock input pin (5 MHz)
12
VDD1
–
Positive power supply (+5V)
13
XT2
O
Sub system clock output pin (32 kHz)
14
XT1
I
Sub system clock output pin (32 kHz)
15
RESET
I
System reset input pin, “L”:RESET
16, 17
–
I
Not used
18
ENCODER A
I
Encoder input pin for jogging
19
ENCODER B
I
Encoder input pin for jogging
20
RDSCLK
I
RDS clock input pin (Not used)
21
RDSDAT
I
RDS data input pin (Not used)
22
SCOR
I
SCOR input pin
23
VDD0
–
Positive power supply of port (+5V)
24
ADREF
–
Reference voltage of A/D converter (+5V)
25
KEY1
I
Key input pin (Analog input)
26
KEY0
I
Key input pin (Analog input)
–
I
Not used
27 to 30
31
HP-SW
I
Headphone detection SW, “L”:No HP, “H”:HP
32
–
I
Not used
33
AVSS
–
A/D converter ground potential
34
–
I
Not used
35
FL.DAT
O
Serial data output for FL tube control IC (MSM9202-02)
36
FL.CLK
O
Serial clock output for FL tube control IC (MSM9202-02)
37
FL.LAT
O
Chip select output for FL tube control IC (MSM9202-02)
38
FL.RST
O
Reset signal output for FL tube control IC (MSM9202-02)
39
–
I
Not used
40
VSS1
–
Ground potential other than port and analog
–
I
Not used
43
SQSI
I
CD sub code data input
44
–
I
Not used
45
SQCK
O
Clock output for reading CD sub code
41, 42
46 to 48
–
I
Not used
49
IN-SW
I
CD tray close completion detection input, “L”:CLOSE
50
OUT-SW
I
CD tray open completion detection input, “L”:OPEN
51
HELP
I
Pin requesting power ON from the PC link adapter (optional), Normally “H”
52
FSW
O
Focus gain switch
53
SENSE
I
SENSE input pin
54
–
55
IIC DAT
I/O
System control communication data input/output pin
56
IIC CLOCK
I/O
System control communication clock input/output pin
57
CD-CLK
O
Serial clock for CD control
58
CD-DATA
O
Serial data for CD control
59
DF-LAT
O
Chip select signal for DA/DF
60
DSP-LAT
O
DSP IC and SSP IC chip select
I
Not used
– 54 –
Pin No.
61
Pin Name
LOAD IN
I/O
O
Function
Tray loading motor control signal, “L”:Loading
62
LOAD OUT
O
Tray loading motor control signal, “L”:When OPEN
63
BD.RESET
O
IC reset signal for CD control, “L”:RESET
64
LIGHT
O
BLUE LED control port of front panel, “L”:LED ON
65
SDATA
O
Serial data for SOUND PROCESSOR IC101 (M62428AFP)
66
SCLOCK
O
Serial clock for SOUND PROCESSOR IC101 (M62428AFP)
67
SLAT1
O
Chip select for SOUND PROCESSOR IC101 (M62428AFP)
68
MUTE1
O
Audio mute signal, “H”:Power amplifier ICs (IC801, IC851) MUTE
69
MUTE2
O
Audio mute signal, “L”:Line mute (Q141, Q241) MUTE
70
STANDBY LED
O
Signal controlling LED which lights when power is OFF, “L”:LED ON
71
VSS0
–
Ground potential of port
72
ON LED
O
Signal controlling LED which lights when power is ON, “L”:LED ON
73
TIMER LED
O
Signal controlling LED which lights in timer standby, “H”:LED ON
74
–
I
Not used
75
FL DISP SW
O
Power ON/OFF signal for FL display, “H”:FL display ON
76
SP RELAY SW
O
Speaker relay control signal, “L”:Speaker relay ON
–
I
Not used
81
ON/XSTBY
O
System power control signal, “H”:Standby relay ON
82
STEREO
I
Tuner stereo signal, “L”:Stereo
83
TUNED
I
Tuner selection OK signal, “L”:TUNED
84
ST IDATA
I
Serial input data for tuner
85
ST ODATA
O
Serial output data for tuner
86
ST.CLOCK
O
Serial clock for tuner
87
ST LATCH
O
Chip select for tuner
88
ST MUTE
O
Tuner mute output
89
ST POWER
O
Tuner power signal (Not used)
90
SIRCS
I
SIRCS code input signal (Remote control signal input)
91
PCL
I
32 KHz clock monitor out
–
I
77 to 80
32.768 kHz signal is output in the test mode (Refer to page 12.)
92, 93
Not used
94
DEST1
I
Destination differentiation signal (Fixed at “H”)
95
DEST2
I
Destination differentiation signal (Fixed at “L”)
96
–
I
Not used
97
HP MUTE
O
HP mute signal output
98
MD-MUTE
O
MD REC OUT control signal “L”:MD REC OUT MUTE (“L” only for MD function)
99
TC-MUTE
O
REC OUT control signal of TAPE
“L”:TAPE REC OUT MUTE (“L” only for TAPE function)
100
V/T
O
Function control signal “H”:TAPE, “L”:CS/BS
– 55 –
SECTION 8
EXPLODED VIEWS
NOTE:
• Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
• The mechanical parts with no reference number in
the exploded views are not supplied.
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
• Hardware (# mark) list and accessories and packing materials are given in the last of this parts list.
• Abbreviation
HK : Hong Kong model
SP
: Singapore model
8-1. FRONT PANEL SECTION
20
14
not supplied
17
19
15
Supplied with J667
14
16
13
12
FL601
18
14
8
19
24
5
not supplied
1
10
11
4
7
2
#2
6
9
not supplied
3
2
3
#1
22
23
14
Ref. No.
21
Part No.
Description
1
2
3
4
5
X-4950-580-1
4-212-584-01
4-993-007-01
4-942-636-21
4-212-538-11
GLASS ASSY (CD)
BRACKET (SHAFT)
SCREW (M2.6X6), +P TAPPING
EMBLEM (NO.3.5), SONY
PANEL (AL-CD), FRONT
6
7
8
9
10
X-4950-364-1
4-212-542-11
X-4950-995-1
4-212-580-11
X-4950-999-1
KNOB (VOL) ASSY
RING (VOL)
PANEL ASSY (CD), FRONT
SPRING (GLASS)
BRACKET (R) ASSY
* 11
12
* 13
1-671-610-11 VOLUME BOARD
X-4950-998-1 BRACKET (L) ASSY
1-671-617-11 PANEL-SW BOARD
Remark
Ref. No.
14
15
Part No.
Description
4-951-620-01 SCREW (2.6X8), +BVTP
1-769-940-11 WIRE (FLAT TYPE) (11 CORE)
16
* 17
* 18
19
* 20
1-769-972-11
1-671-609-11
A-4419-060-A
3-363-099-51
4-212-561-31
WIRE (FLAT TYPE) (13 CORE)
HP BOARD
PANEL BOARD, COMPLETE
SCREW (CASE 3 TP2)
CASE
21
22
23
* 24
FL601
4-212-540-11
4-212-541-11
4-212-545-11
4-212-590-11
1-517-805-11
PANEL (AL-CD), LOADING
PANEL (CD), LOADING
PLATE (CD), ORNAMENTAL
HOLDER (FL)
INDICATOR TUBE, FLUORESCENT
– 56 –
Remark
8-2. CHASSIS SECTION
not supplied
55
not supplied
#1
#2
#1
66
not supplied
T991
65(UK,HK)
64
#2
56
#2
67
51
#1
#1
CN904
not
supplied
#1
57
#1
#5
58
M551
#2
#4
#2
CDM13B-5BD19
#2
#2
#2
54
#2
#4
53
61
59
not
supplied
60
52
62
63
not supplied
#1
#2
not supplied
#2
#2
63
#2
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
Ref. No.
Part No.
Description
* 51
* 51
* 52
53
54
A-4419-059-A
A-4419-070-A
A-4419-068-A
1-790-305-11
1-693-408-11
MAIN BOARD, COMPLETE (AEP,UK)
MAIN BOARD, COMPLETE (SP,HK)
REG BOARD, COMPLETE
WIRE (FLAT TYPE) (19 CORE)
TUNER
* 55
* 56
! 57
* 58
* 59
1-671-615-11
A-4419-064-A
1-575-651-91
3-703-244-00
4-212-564-11
TRANS BOARD
CHEMI-CON BOARD, COMPLETE
CORD, POWER
BUSHING (2104), CORD
PANEL (CD), BACK
60
Remark
Ref. No.
Part No.
Description
* 61
* 62
63
* 64
A-4419-065-A
1-671-614-11
X-4950-994-1
1-671-611-11
SUB-TRANS BOARD, COMPLETE
CONNECTOR BOARD
FOOT ASSY
AMP BOARD
! 65
66
67
! CN904
M551
1-770-019-11
3-531-576-01
3-655-653-01
1-526-794-11
1-698-997-21
ADAPTOR, CONVERSION PLUG 3P (UK,HK)
RIVET
BAND (TAITON), BINDING
OUTLET, AC
FAN, D.C.
! T991
1-433-478-11 TRANSFORMER, POWER
1-773-108-11 WIRE (FLAT TYPE) (19 CORE)(100mm)
– 57 –
Remark
8-3. MECHANISM DECK SECTION (CDM13B-5BD19)
#2
not supplied
211
#2
212
#6
207
208
205
#2
#2
209
206
210
#7
#8
214
213
219
204
218
215
203
202
BU-5BD19
215
#6
M904
216
216
201
not supplied
217
Ref. No.
Part No.
Description
* 201
202
203
204
205
1-634-461-11
4-927-654-01
3-659-338-00
4-929-764-01
4-927-620-01
LOADING BOARD
WASHER (LIMITER)
SPRING, COMPRESSION
SHAFT (TABLE GUIDE)
GEAR (P)
206
207
208
209
210
4-944-006-11
4-927-628-01
4-927-649-01
4-929-724-01
X-4947-265-1
BEARING
GEAR (C)
BELT
PULLEY (B)
ARM ASSY, SWING
Remark
Ref. No.
Part No.
Description
211
212
* 213
214
215
4-944-012-01
A-4604-752-A
4-917-583-21
X-4941-462-1
4-933-134-01
TABLE, DISC
HOLDER (MG) ASSY
BRACKET, YOKE
CHASSIS (MD) ASSY
SCREW (+PTPWH M2.6X6)
4-958-593-01
4-929-747-01
4-929-727-01
4-929-729-01
A-4660-307-A
SPRING (BU), COMPRESSION
HOLDER (BU)
CAM (A)
CAM (B)
MOTOR (L) ASSY (LOADING)
216
217
218
219
M904
– 58 –
Remark
8-4. BASE UNIT SECTION (BU-5BD19)
255
256
259
257
M101
253
254
M102
254
258
252
251
Ref. No.
Part No.
Description
251
* 252
253
254
! 255
4-951-620-01
A-4673-402-B
4-917-565-01
4-951-940-01
8-848-379-31
SCREW (2.6X8), +BVTP
BD BOARD, COMPLETE
SHAFT, SLED
INSULATOR (BU)
OPTICAL PICK-UP KSS-213B/S-N
256
Remark
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
Ref. No.
Part No.
Description
257
258
259
M101
4-917-567-01
4-917-564-01
3-713-786-51
X-4917-523-4
GEAR (M)
GEAR (P), FLATNESS
SCREW +P 2X3
MOTOR ASSY (SPINDLE)
M102
X-4917-504-1 MOTOR ASSY (SLED)
1-769-069-11 WIRE (FLAT TYPE) (16 CORE)
– 59 –
Remark
AMP
SECTION 9
ELECTRICAL PARTS LIST
BD
Note:
The components identified by
mark ! or dotted line with mark
! are critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board
name.
Ref. No.
Part No.
*
1-671-611-11 AMP BOARD
*********
• Due to standardization, replacements in the parts list
may be different from the parts specified in the
diagrams or the components used on the set.
• -XX, -X mean standardized parts, so they may have
some difference from the original one.
• Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
• RESISTORS
All resistors are in ohms
METAL: Metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F : nonflammable
Description
Remark
Ref. No.
Part No.
• SEMICONDUCTORS
In each case, u: µ , for example:
uA...: µ A..., uPA...: µ PA..., uPB...: µ PB...,
uPC...: µ PC..., uPD...: µ PD...
• CAPACITORS
uF : µ F
• COILS
uH : µ H
• Abbreviation
HK : Hong Kong model
SP
: Singapore model
Description
Remark
C103
C105
C106
1-164-346-11 CERAMIC CHIP
1-163-038-91 CERAMIC CHIP
1-164-690-91 CERAMIC CHIP
1uF
0.1uF
0.0022uF 5%
16V
25V
50V
C107
C108
C109
C110
C111
1-164-690-91
1-163-021-91
1-163-021-91
1-163-989-11
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF
0.01uF
0.01uF
0.033uF
0.1uF
5%
10%
10%
10%
50V
50V
50V
25V
25V
C112
C113
C114
C115
C116
1-163-038-91
1-164-690-91
1-164-005-11
1-126-607-11
1-163-016-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.1uF
0.0022uF 5%
0.47uF
47uF
20%
0.0039uF 10%
25V
50V
25V
4V
50V
C117
C118
C119
C120
C121
1-164-005-11
1-107-823-11
1-163-038-91
1-135-201-11
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
0.47uF
0.47uF
0.1uF
10uF
0.1uF
25V
16V
25V
4V
25V
C122
C123
C124
C125
C126
1-163-021-91
1-163-038-91
1-126-607-11
1-163-021-91
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
47uF
0.01uF
0.1uF
C127
C128
C129
C130
C131
1-164-690-91
1-163-135-00
1-163-038-91
1-164-336-11
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0022uF 5%
560PF
5%
0.1uF
0.33uF
0.1uF
50V
50V
25V
25V
25V
C132
C133
C134
C135
C136
1-163-037-11
1-163-145-00
1-164-346-11
1-163-251-11
1-164-005-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF 10%
0.0015uF 5%
1uF
100PF
5%
0.47uF
25V
50V
16V
50V
25V
C137
C139
C140
C141
C142
1-163-021-91
1-163-235-11
1-163-235-11
1-163-038-91
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
22PF
22PF
0.1uF
0.1uF
10%
5%
5%
50V
50V
50V
25V
25V
C145
C146
C147
C148
C149
1-135-201-11
1-135-201-11
1-163-275-11
1-163-275-11
1-164-346-11
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
10uF
0.001uF
0.001uF
1uF
20%
20%
5%
5%
4V
4V
50V
50V
16V
C153
C154
1-135-259-11 TANTAL. CHIP
1-163-235-11 CERAMIC CHIP
10uF
22PF
20%
5%
6.3V
50V
< CAPACITOR >
C801
C803
C804
C805
C806
1-124-720-11
1-162-215-31
1-124-724-11
1-162-215-31
1-164-159-11
ELECT
CERAMIC
ELECT
CERAMIC
CERAMIC
4.7uF
47PF
47uF
47PF
0.1uF
C807
C808
C809
C841
C842
1-164-159-11
1-164-159-11
1-163-038-91
1-126-948-11
1-126-948-11
CERAMIC
CERAMIC
CERAMIC
ELECT
ELECT
0.1uF
0.1uF
0.1uF
100uF
100uF
C851
C853
C854
C855
C856
1-124-720-11
1-162-215-31
1-124-724-11
1-162-215-31
1-164-159-11
ELECT
CERAMIC
ELECT
CERAMIC
CERAMIC
4.7uF
47PF
47uF
47PF
0.1uF
C857
1-164-159-11 CERAMIC
0.1uF
20%
5%
20%
5%
20%
20%
20%
5%
20%
5%
50V
50V
50V
50V
50V
50V
50V
25V
35V
35V
50V
50V
50V
50V
50V
50V
< IC >
IC801
IC851
8-759-331-41 IC LM3876TF
8-759-331-41 IC LM3876TF
< RESISTOR >
R801
R802
R803
R804
R805
1-249-417-11
1-249-437-11
1-249-417-11
1-249-437-11
1-249-433-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
47K
1K
47K
22K
5%
5%
5%
5%
5%
1/4W F
1/4W
1/4W F
1/4W
1/4W
R806
R851
R852
R853
R854
1-249-389-11
1-249-417-11
1-249-437-11
1-249-417-11
1-249-437-11
CARBON
CARBON
CARBON
CARBON
CARBON
4.7
1K
47K
1K
47K
5%
5%
5%
5%
5%
1/4W F
1/4W F
1/4W
1/4W F
1/4W
R855
R856
1-249-433-11 CARBON
1-249-389-11 CARBON
22K
4.7
5%
5%
1/4W
1/4W F
**************************************************************
A-4673-402-B BD BOARD, COMPLETE
******************
*
< CAPACITOR >
C101
C102
1-126-607-11 ELECT CHIP
1-163-275-11 CERAMIC CHIP
47uF
0.001uF
20%
5%
4V
50V
– 60 –
10%
20%
10%
20%
10%
50V
25V
4V
50V
25V
BD
Ref. No.
Part No.
Description
Remark
Ref. No.
< CONNECTOR >
CNU101 1-770-014-11 CONNECTOR, FFC/FPC 16P
CNU102 1-770-013-11 CONNECTOR, FFC/FPC 19P
< IC >
IC101
IC102
IC103
IC104
8-752-074-34
8-759-291-06
8-752-372-94
8-759-185-29
IC
IC
IC
IC
CXA1782BQ
BA6397FP
CXD2507AQ
PCM1710U-B
< TRANSISTOR >
Q101
Q102
Q103
8-729-010-08 TRANSISTOR MSB710-R
8-729-424-08 TRANSISTOR UN2111
8-729-421-22 TRANSISTOR UN2211
CHEMI-CON
Part No.
Description
R145
R146
R147
R148
1-216-097-91
1-216-097-91
1-216-049-91
1-216-049-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
100K
100K
1K
1K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
Remark
R149
R150
R151
R152
R153
1-216-049-91
1-216-037-00
1-216-037-00
1-216-037-00
1-216-082-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
1K
330
330
330
24K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R154
R156
R157
R158
1-216-065-91
1-216-085-00
1-216-069-00
1-216-001-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
33K
6.8K
10
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
< VARIABLE RESISTOR >
< RESISTOR >
R102
R103
R104
R105
R106
1-216-001-00
1-216-049-91
1-216-097-91
1-216-093-91
1-216-093-91
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
10
1K
100K
68K
68K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R107
R108
R109
R112
R113
1-216-093-91
1-216-093-91
1-216-097-91
1-216-083-00
1-216-083-00
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
68K
68K
100K
27K
27K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R114
R115
R116
R117
R118
1-216-101-00
1-216-101-00
1-216-061-00
1-216-069-00
1-216-049-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
150K
150K
3.3K
6.8K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R119
R120
R121
R122
R123
1-216-089-91
1-216-089-91
1-216-114-00
1-216-097-91
1-216-099-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
47K
47K
510K
100K
120K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R124
R125
R126
R127
R128
1-216-091-00
1-216-069-00
1-216-063-91
1-216-089-91
1-216-105-91
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
56K
6.8K
3.9K
47K
220K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R129
R130
R131
R132
R133
1-216-049-91
1-216-079-00
1-216-079-00
1-216-061-00
1-216-061-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
18K
18K
3.3K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R134
R135
R136
R137
R138
1-216-065-91
1-216-065-91
1-216-073-00
1-216-065-91
1-216-049-91
RES,CHIP
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
4.7K
4.7K
10K
4.7K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R139
R140
R141
R142
R143
1-216-033-00
1-216-081-00
1-216-061-00
1-216-061-00
1-216-121-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
220
22K
3.3K
3.3K
1M
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R144
1-216-073-00 METAL CHIP
10K
5%
1/10W
RV101
RV102
RV103
1-223-587-11 RES, ADJ, CARBON 22K
1-223-587-11 RES, ADJ, CARBON 22K
1-223-587-11 RES, ADJ, CARBON 22K
< SWITCH >
S101
1-572-085-11 SWITCH, LEAF (LIMIT)
< VIBRATOR >
X101
1-579-280-11 VIBRATOR, CRYSTAL (16.9344MHz)
**************************************************************
A-4419-064-A CHEMI-CON BOARD, COMPLETE
*************************
*
< CAPACITOR >
C503
C551
C553
C554
C555
1-126-948-11
1-128-131-11
1-126-933-11
1-164-159-11
1-163-038-91
ELECT
ELECT
ELECT
CERAMIC
CERAMIC CHIP
100uF
22uF
100uF
0.1uF
0.1uF
20%
20%
20%
35V
50V
16V
50V
25V
C556
C971
C972
C975
C976
1-126-948-11
1-126-042-11
1-126-042-11
1-136-165-00
1-136-165-00
ELECT
ELECT
ELECT
FILM
FILM
100uF
3300uF
3300uF
0.1uF
0.1uF
20%
20%
20%
5%
5%
35V
35V
35V
50V
50V
< CONNECTOR >
* CN501
* CN551
1-770-729-11 CONNECTOR, BOARD TO BOARD 10P
1-564-506-11 PLUG, CONNECTOR 3P
< DIODE >
D553
D554
D971
D972
8-719-933-47
8-719-933-39
8-719-062-40
8-719-024-99
DIODE
DIODE
DIODE
DIODE
HZS7B2L
HZS6C1L
D4SBL20UF3
11ES2-NTA2B
< TRANSISTOR >
Q505
Q551
Q552
Q553
– 61 –
8-729-900-53
8-729-620-05
8-729-620-05
8-729-026-68
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114EK
2SC2603-EF
2SC2603-EF
2SD2525(TP)
CHEMI-CON
Ref. No.
Part No.
CONNECTOR
LOADING
HP
Description
Remark
Ref. No.
L861
< RESISTOR >
R505
R506
R551
R552
R553
1-216-097-91
1-216-085-00
1-216-049-91
1-216-097-91
1-247-887-00
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
CARBON
100K
33K
1K
100K
220K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/4W
R554
R821
R822
R871
R872
1-216-065-91
1-260-089-11
1-260-089-11
1-260-089-11
1-260-089-11
RES,CHIP
CARBON
CARBON
CARBON
CARBON
4.7K
150
150
150
150
5%
5%
5%
5%
5%
1/10W
1/2W
1/2W
1/2W
1/2W
Description
Remark
< TRANSISTOR >
Q501
Q502
Q503
Q504
8-729-029-66
8-729-620-05
8-729-620-05
8-729-620-05
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114ESA
2SC2603-EF
2SC2603-EF
2SC2603-EF
< RESISTOR >
**************************************************************
R501
R502
R503
! R504
R556
1-671-614-11 CONNECTOR BOARD
***************
*
Part No.
1-420-872-00 COIL, AIR-CORE
1-247-887-00
1-249-389-11
1-249-438-11
1-219-122-91
1-249-441-11
CARBON
CARBON
CARBON
FUSIBLE
CARBON
220K
4.7
56K
0.33
100K
5%
5%
5%
5%
5%
1/4W
1/4W F
1/4W
1/4W F
1/4W
R557
R806
1-249-441-11 CARBON
1-249-389-11 CARBON
100K
4.7
5%
5%
R809
R811
R856
1-249-437-11 CARBON
1-260-076-11 CARBON
1-249-389-11 CARBON
47K
10
4.7
5%
5%
5%
1/4W
1/4W F
(AEP,UK)
1/4W
1/2W
1/4W F
(AEP,UK)
R859
R861
R881
R882
R883
1-249-438-11
1-260-076-11
1-249-431-11
1-249-431-11
1-249-425-11
56K
10
15K
15K
4.7K
5%
5%
5%
5%
5%
< CAPACITOR >
C311
C312
C501
C502
C781
1-126-933-11
1-164-159-11
1-126-933-11
1-126-948-11
1-164-159-11
ELECT
CERAMIC
ELECT
ELECT
CERAMIC
100uF
0.1uF
100uF
100uF
0.1uF
C782
C785
C811
1-164-159-11 CERAMIC
1-164-159-11 CERAMIC
1-164-159-11 CERAMIC
0.1uF
0.1uF
0.1uF
C812
1-164-159-11 CERAMIC
0.1uF
C813
1-164-159-11 CERAMIC
0.1uF
C861
1-164-159-11 CERAMIC
0.1uF
C862
1-164-159-11 CERAMIC
0.1uF
C863
1-164-159-11 CERAMIC
0.1uF
20%
20%
20%
16V
50V
16V
35V
50V
50V
50V
50V
(AEP,UK)
50V
(AEP,UK)
50V
(AEP,UK)
CARBON
CARBON
CARBON
CARBON
CARBON
1/4W
1/2W
1/4W
1/4W
1/4W F
< RELAY >
RY501
1-515-920-11 RELAY (24V)
< TERMINAL >
50V
(AEP,UK)
50V
(AEP,UK)
50V
(AEP,UK)
TM811
1-537-842-11 TERMINAL BOARD (SPEAKER)
**************************************************************
1-671-609-11 HP BOARD
********
*
< CONNECTOR >
< CAPACITOR >
* CN781
CN811
* CN961
CN962
D501
D556
D557
D881
1-566-856-11
1-766-921-11
1-774-813-11
1-695-342-31
8-719-911-19
8-719-911-19
8-719-911-19
8-719-911-19
SOCKET, CONNECTOR 5P
CONNECTOR, BOARD TO BOARD 10P
CONNECTOR, BOARD TO BOARD 7P
PIN, CONNECTOR (PC BOARD) 19P
C681
C682
C683
1-162-294-31 CERAMIC
1-162-294-31 CERAMIC
1-164-159-11 CERAMIC
0.001uF
0.001uF
0.1uF
< DIODE >
C684
1-164-159-11 CERAMIC
0.1uF
DIODE
DIODE
DIODE
DIODE
1SS119-25
1SS119-25
1SS119-25
1SS119-25
10%
10%
50V
50V
50V
(AEP,UK)
50V
< JACK >
J667
1-774-933-11 JACK (LARGE TYPE)(PHONES)
**************************************************************
< FERRITE BEAD >
1-634-461-11 LOADING BOARD
*************
*
FB782
1-412-473-21 INDUCTOR
0UH
< CONNECTOR >
< IC >
IC311
* CN291
8-749-923-04 IC TOTX178 (DIGITAL OPTICAL CD AUX)
< SWITCH >
< COIL >
L311
L801
1-564-498-11 PIN, CONNECTOR 5P
S291
S292
1-410-322-11 INDUCTOR
3.3uH
1-420-872-00 COIL, AIR-CORE
–
1-571-924-11 SWITCH, LEAF (LOAD OUT)
1-571-924-11 SWITCH, LEAF (LOAD IN)
**************************************************************
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
62 –
MAIN
Ref. No.
Part No.
*
A-4419-059-A MAIN BOARD, COMPLETE (AEP,UK)
********************
Description
Remark
*
A-4419-070-A MAIN BOARD, COMPLETE (SP,HK)
********************
*
4-212-590-11 HOLDER (FL)
< CAPACITOR >
C100
C101
C102
C103
C104
1-216-295-91
1-163-251-11
1-163-251-11
1-163-251-11
1-163-251-11
SHORT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0
100PF
100PF
100PF
100PF
C105
C106
C107
C121
C122
1-163-251-11
1-164-159-11
1-163-038-91
1-126-022-11
1-130-475-00
CERAMIC CHIP
CERAMIC
CERAMIC CHIP
ELECT
MYLAR
100PF
5%
0.1uF
0.1uF
47uF
20%
0.0022uF 5%
50V
50V
25V
10V
50V
C123
C126
C127
C128
C129
1-126-964-11
1-126-963-11
1-126-963-11
1-126-963-11
1-126-964-11
ELECT
ELECT
ELECT
ELECT
ELECT
10uF
4.7uF
4.7uF
4.7uF
10uF
20%
20%
20%
20%
20%
50V
50V
50V
50V
50V
C130
C131
C132
C134
C135
1-136-165-00
1-126-957-11
1-130-479-00
1-136-165-00
1-136-165-00
FILM
ELECT
MYLAR
FILM
FILM
0.1uF
0.22uF
0.0047uF
0.1uF
0.1uF
5%
20%
5%
5%
5%
50V
50V
50V
50V
50V
C137
C139
C141
C142
C143
1-126-961-11
1-164-005-11
1-126-043-11
1-126-963-11
1-163-133-00
ELECT
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
2.2uF
0.47uF
0.47uF
4.7uF
470PF
20%
20%
20%
5%
50V
25V
50V
50V
50V
C191
C192
C193
C194
C195
1-164-159-11
1-163-038-91
1-163-038-91
1-163-141-00
1-163-141-00
CERAMIC
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.001uF
0.001uF
5%
5%
50V
25V
25V
50V
50V
C196
C197
C198
C199
C201
1-162-294-31
1-124-995-11
1-164-159-11
1-124-995-11
1-163-251-11
CERAMIC
ELECT
CERAMIC
ELECT
CERAMIC CHIP
0.001uF
220uF
0.1uF
220uF
100PF
10%
20%
20%
5%
50V
10V
50V
10V
50V
C202
C203
C204
C205
C221
1-163-251-11
1-163-251-11
1-163-251-11
1-163-251-11
1-126-022-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
100PF
100PF
100PF
100PF
47uF
5%
5%
5%
5%
20%
50V
50V
50V
50V
10V
C222
C223
C224
C226
C227
1-130-475-00
1-130-471-00
1-104-664-11
1-126-963-11
1-126-963-11
MYLAR
MYLAR
ELECT
ELECT
ELECT
0.0022uF
0.001uF
47uF
4.7uF
4.7uF
5%
5%
20%
20%
20%
50V
50V
16V
50V
50V
C228
C229
C230
C231
C232
1-126-963-11
1-126-964-11
1-136-165-00
1-126-957-11
1-130-479-00
ELECT
ELECT
FILM
ELECT
MYLAR
4.7uF
10uF
0.1uF
0.22uF
0.0047uF
20%
20%
5%
20%
5%
50V
50V
50V
50V
50V
5%
5%
5%
5%
50V
50V
50V
50V
Ref. No.
Part No.
Description
C234
C235
C237
C241
C242
1-136-165-00
1-136-165-00
1-126-961-11
1-126-043-11
1-126-963-11
FILM
FILM
ELECT
ELECT
ELECT
0.1uF
0.1uF
2.2uF
0.47uF
4.7uF
5%
5%
20%
20%
20%
50V
50V
50V
50V
50V
Remark
C243
C301
C302
C303
C304
1-163-133-00
1-124-997-11
1-163-038-91
1-124-473-11
1-163-038-91
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
470PF
470uF
0.1uF
1000uF
0.1uF
5%
20%
50V
10V
25V
10V
25V
C305
C306
C351
C352
C353
1-163-251-11
1-163-251-11
1-104-664-11
1-163-031-11
1-162-306-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC
100PF
100PF
47uF
0.01uF
0.01uF
5%
5%
20%
C354
C401
C402
C403
1-163-031-11
1-162-294-31
1-162-294-31
1-162-306-11
CERAMIC CHIP
CERAMIC
CERAMIC
CERAMIC
0.01uF
0.001uF
0.001uF
0.01uF
10%
10%
20%
C404
1-162-306-11 CERAMIC
0.01uF
20%
C405
C451
1-163-251-11 CERAMIC CHIP
1-126-961-11 ELECT
100PF
2.2uF
5%
20%
C452
1-162-306-11 CERAMIC
0.01uF
20%
C453
1-162-291-31 CERAMIC
560PF
10%
C454
1-126-964-11 ELECT
10uF
20%
C455
1-162-306-11 CERAMIC
0.01uF
20%
C456
1-163-239-11 CERAMIC CHIP
33PF
5%
C457
1-163-239-11 CERAMIC CHIP
33PF
5%
C701
C702
1-163-102-00 CERAMIC CHIP
1-163-233-11 CERAMIC CHIP
24PF
18PF
5%
5%
C703
C704
C748
C751
C752
1-163-038-91
1-163-038-91
1-164-159-11
1-124-589-11
1-163-038-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC
ELECT
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
47uF
0.1uF
C753
C754
C755
C756
C757
1-126-925-11
1-163-038-91
1-124-589-11
1-164-159-11
1-164-159-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC
CERAMIC
470uF
0.1uF
47uF
0.1uF
0.1uF
C758
C759
C791
1-164-159-11 CERAMIC
1-104-905-11 CAPACITOR
1-163-038-91 CERAMIC CHIP
0.1uF
0.22F
0.1uF
20%
20%
20%
20%
20%
< CONNECTOR >
* CN101
CN301
* CN351
CN401
CN701
– 63 –
1-564-506-11
1-770-067-11
1-564-339-00
1-774-289-11
1-784-601-11
PLUG, CONNECTOR 3P
CONNECTOR, FFC/FPC 19P
PIN, CONNECTOR 5P
PIN, CONNECTOR (PC BOARD) 15P
SOCKET, CONNECTOR (NON ZIF)13P
50V
50V
16V
50V
16V
50V
50V
50V
16V
(AEP,UK)
16V
(AEP,UK)
50V
50V
(AEP,UK)
16V
(AEP,UK)
50V
(AEP,UK)
50V
(AEP,UK)
16V
(AEP,UK)
50V
(AEP,UK)
50V
(AEP,UK)
50V
50V
25V
25V
50V
16V
25V
10V
25V
16V
50V
16V
50V
5.5V
25V
MAIN
Ref. No.
CN702
CN703
CN704
CN705
Part No.
Description
1-785-462-11
1-770-380-11
1-770-380-11
1-695-342-31
SOCKET, CONNECTOR (NON-ZIF)11P
CONNECTOR, BOARD TO BOARD 8P
CONNECTOR, BOARD TO BOARD 8P
PIN, CONNECTOR (PC BOARD) 19P
Remark
< DIODE >
D351
D751
D752
D753
D755
8-719-921-40
8-719-911-19
8-719-024-99
8-719-911-19
8-719-911-19
DIODE
DIODE
DIODE
DIODE
DIODE
MTZJ-4.7C
1SS119-25
11ES2-NTA2B
1SS119-25
1SS119-25
D791
D792
D793
8-719-914-42 DIODE DA204K
8-719-914-42 DIODE DA204K
8-719-914-42 DIODE DA204K
< FERRITE BEAD >
FB301
FB791
FB792
1-412-473-21 INDUCTOR
1-500-445-21 FERRITE
1-500-445-21 FERRITE
0UH
0UH
0UH
< IC >
IC101
IC102
IC103
IC351
IC451
8-759-494-40
8-759-300-71
8-759-100-96
8-759-822-09
8-759-560-51
IC
IC
IC
IC
IC
M62428AFP600C
HD14053BFP
UPC4558G2
LB1641
BU1924F (AEP,UK)
IC701
IC791
IC951
8-759-549-47 IC uPD780018AYGF-015-3BA
8-759-549-80 IC P82B715TD.118
8-759-635-63 IC M51943BSL
Ref. No.
L405
Part No.
Description
Remark
1-410-482-31 INDUCTOR
100uH
< TRANSISTOR >
Q103
Q111
Q112
Q121
Q141
8-729-900-53
8-729-107-46
8-729-107-46
8-729-120-28
8-729-107-46
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114EK
2SC3624A-L15
2SC3624A-L15
2SC1623-L5L6
2SC3624A-L15
Q181
Q182
Q183
Q211
Q212
8-729-029-21
8-729-029-21
8-729-029-21
8-729-107-46
8-729-107-46
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA114ESA-TP
DTA114ESA-TP
DTA114ESA-TP
2SC3624A-L15
2SC3624A-L15
Q222
Q241
Q450
Q751
Q752
8-729-120-28
8-729-107-46
8-729-620-05
8-729-620-05
8-729-600-22
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC1623-L5L6
2SC3624A-L15
2SC2603-EF
2SC2603-EF
2SA1235-F
Q753
Q781
Q782
Q783
Q791
8-729-027-23
8-729-027-23
8-729-107-46
8-729-107-46
8-729-025-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA114EK
DTA114EK
2SC3624A-L15
2SC3624A-L15
2SK1828
Q792
8-729-025-28 TRANSISTOR 2SK1828
< RESISTOR >
< JACK >
J101
J102
1-766-396-11 JACK, PIN 4P (MD IN/OUT)
1-779-688-11 JACK, PIN 6P (TAPE,CS/BS IN/OUT)
< JUMPER RESISTOR >
JW301
JW302
JW303
JW304
JW412
1-216-295-91
1-216-295-91
1-216-296-91
1-216-296-91
1-216-295-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JW413
JW701
JW734
JW735
JW791
1-216-295-91
1-216-296-91
1-216-295-91
1-216-295-91
1-216-295-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0 (SP, HK)
0
JW792
JW793
JW794
JW795
JW796
1-216-296-91
1-216-296-91
1-216-296-91
1-216-295-91
1-216-296-91
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JW797
JW798
1-216-296-91 SHORT
1-216-296-91 SHORT
0
0
< COIL >
L401
L402
L403
L404
1-410-482-31
1-410-482-31
1-410-482-31
1-410-482-31
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
100uH
100uH
100uH
100uH
R101
R102
R103
R104
R105
1-216-077-00
1-216-073-00
1-216-033-00
1-216-049-91
1-216-105-91
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
15K
10K
220
1K
220K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R106
R107
R108
R109
R111
1-216-033-00
1-216-077-00
1-216-073-00
1-216-089-91
1-216-049-91
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
220
15K
10K
47K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R112
R113
R114
R115
R116
1-216-065-91
1-216-049-91
1-216-065-91
1-216-097-91
1-216-093-91
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
4.7K
1K
4.7K
100K
68K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R117
R123
R124
R125
R126
1-216-089-91
1-216-055-00
1-216-069-00
1-216-104-00
1-216-081-00
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
1.8K
6.8K
200K
22K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R127
R128
R129
R130
R139
1-216-061-00
1-216-081-00
1-216-121-91
1-216-073-00
1-216-121-91
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
3.3K
22K
1M
10K
1M
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R141
R142
R143
R181
R183
1-216-057-00
1-216-065-91
1-216-089-91
1-247-887-00
1-247-887-00
METAL CHIP
RES,CHIP
RES,CHIP
CARBON
CARBON
2.2K
4.7K
47K
220K
220K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/4W
1/4W
R185
1-247-887-00 CARBON
220K
5%
1/4W
– 64 –
MAIN
Ref. No.
Part No.
Description
R191
R192
R193
R201
1-249-413-11
1-249-413-11
1-249-413-11
1-216-077-00
CARBON
CARBON
CARBON
METAL CHIP
470
470
470
15K
5%
5%
5%
5%
Remark
1/4W F
1/4W F
1/4W F
1/10W
R202
R203
R204
R205
R206
1-216-073-00
1-216-033-00
1-216-049-91
1-216-105-91
1-216-033-00
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
10K
220
1K
220K
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R207
R208
R211
R212
R213
1-216-077-00
1-216-073-00
1-216-049-91
1-216-065-91
1-216-049-91
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
15K
10K
1K
4.7K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R214
R215
R216
R217
R223
1-216-065-91
1-216-097-91
1-216-093-91
1-216-089-91
1-216-055-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
4.7K
100K
68K
47K
1.8K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R224
R225
R227
R228
R229
1-216-069-00
1-216-104-00
1-216-061-00
1-216-081-00
1-216-121-91
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
6.8K
200K
3.3K
22K
1M
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R230
R241
R242
R243
R351
1-216-073-00
1-249-421-11
1-216-065-91
1-216-089-91
1-247-807-31
METAL CHIP
CARBON
RES,CHIP
RES,CHIP
CARBON
10K
2.2K
4.7K
47K
100
5%
5%
5%
5%
5%
1/10W
1/4W F
1/10W
1/10W
1/4W
R401
R402
R403
R404
R405
1-249-417-11
1-249-417-11
1-216-025-91
1-216-025-91
1-216-025-91
CARBON
CARBON
RES,CHIP
RES,CHIP
RES,CHIP
1K
1K
100
100
100
5%
5%
5%
5%
5%
R406
R407
1-216-025-91 RES,CHIP
1-249-405-11 CARBON
100
100
5%
5%
R408
1-249-429-11 CARBON
10K
5%
R409
1-249-417-11 CARBON
1K
5%
R410
1-216-073-00 METAL CHIP
10K
5%
R411
! R451
1-216-073-00 METAL CHIP
1-249-401-11 CARBON
10K
47
5%
5%
R452
1-216-129-00 METAL CHIP
2.2M
5%
R453
1-216-049-91 RES,CHIP
1K
5%
R454
1-249-409-11 CARBON
220
5%
R455
1-249-409-11 CARBON
220
5%
R456
R457
R701
R702
1-249-441-11
1-249-441-11
1-249-425-11
1-216-109-00
CARBON
CARBON
CARBON
METAL CHIP
100K
100K
4.7K
330K
5%
5%
5%
5%
1/4W F
(AEP,UK)
1/4W
1/4W
1/4W F
1/10W
R704
R705
1-216-061-00 METAL CHIP
1-216-061-00 METAL CHIP
3.3K
3.3K
5%
5%
1/10W
1/10W
Ref. No.
Part No.
PANEL
Description
Remark
R706
R707
R708
1-216-073-00 METAL CHIP
1-216-073-00 METAL CHIP
1-216-097-91 RES,CHIP
10K
10K
100K
5%
5%
5%
1/10W
1/10W
1/10W
R709
R710
R711
R712
R713
1-216-025-91
1-216-025-91
1-216-025-91
1-216-025-91
1-216-073-00
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
100
100
100
100
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R714
R719
R720
R721
R722
1-216-073-00
1-216-049-91
1-247-807-31
1-247-807-31
1-247-807-31
METAL CHIP
RES,CHIP
CARBON
CARBON
CARBON
10K
1K
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/4W
1/4W
R723
R724
R725
R726
R727
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
CARBON
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
R728
R730
R731
R732
R733
1-216-025-91
1-247-807-31
1-247-807-31
1-247-807-31
1-247-807-31
RES,CHIP
CARBON
CARBON
CARBON
CARBON
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/4W
1/4W
1/4W
1/4W
R735
1-216-097-91 RES,CHIP
100K
5%
R734
R736
R738
R739
1-216-097-91
1-216-097-91
1-247-807-31
1-216-097-91
RES,CHIP
RES,CHIP
CARBON
RES,CHIP
100K
100K
100
100K
5%
5%
5%
5%
1/10W
(AEP,UK)
1/10W
1/10W
1/4W
1/10W
1/4W F
1/4W F
1/10W
1/10W
1/10W
R740
R741
R751
R752
R753
1-249-417-11
1-216-073-00
1-249-417-11
1-249-425-11
1-249-437-11
CARBON
METAL CHIP
CARBON
CARBON
CARBON
1K
10K
1K
4.7K
47K
5%
5%
5%
5%
5%
1/4W F
1/10W
1/4W F
1/4W F
1/4W
1/10W
1/4W F
(AEP,UK)
1/4W F
(AEP,UK)
1/4W F
(AEP,UK)
1/10W
R754
R755
R756
R781
R782
1-249-437-11
1-249-429-11
1-216-025-91
1-216-073-00
1-216-045-00
CARBON
CARBON
RES,CHIP
METAL CHIP
METAL CHIP
47K
10K
100
10K
680
5%
5%
5%
5%
5%
1/4W
1/4W
1/10W
1/10W
1/10W
R783
R791
R792
R793
R794
1-216-045-00
1-216-065-91
1-216-065-91
1-216-065-91
1-216-065-91
METAL CHIP
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
680
4.7K
4.7K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/4W F
(AEP,UK)
1/10W
(AEP,UK)
1/10W
(AEP,UK)
1/4W F
(AEP,UK)
< VIBRATOR >
X601
X701
X702
1-579-900-21 VIBRATOR, CRYSTAL (4.332MHz)(AEP,UK)
1-579-233-11 VIBRATOR, CERAMIC (5MHz)
1-567-098-41 VIBRATOR, CRYSTAL (32kHz)
**************************************************************
A-4419-060-A PANEL BOARD, COMPLETE
*********************
*
< CAPACITOR >
C601
C602
C603
– 65 –
1-163-141-00 CERAMIC CHIP
1-163-141-00 CERAMIC CHIP
1-163-141-00 CERAMIC CHIP
0.001uF
0.001uF
0.001uF
5%
5%
5%
50V
50V
50V
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
PANEL
Ref. No.
PANEL-SW
Part No.
REG
Description
Remark
C604
C605
1-163-141-00 CERAMIC CHIP
1-162-290-31 CERAMIC
0.001uF
470PF
C607
C608
C609
C610
C611
1-163-038-91
1-164-159-11
1-164-159-11
1-162-215-31
1-164-159-11
0.1uF
0.1uF
0.1uF
47PF
0.1uF
C612
C613
1-124-589-11 ELECT
1-128-131-11 ELECT
CERAMIC CHIP
CERAMIC
CERAMIC
CERAMIC
CERAMIC
47uF
22uF
5%
10%
5%
20%
20%
25V
50V
50V
50V
50V
16V
50V
Part No.
Description
S622
S623
S624
S625
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (±/), TUNING +)
SWITCH, KEYBOARD (≠/0, TUNING -)
SWITCH, KEYBOARD (π)
SWITCH, KEYBOARD (fl)
S631
S632
S633
S634
1-762-875-21
1-762-875-21
1-762-875-21
1-762-875-21
SWITCH, KEYBOARD (1/u)
SWITCH, KEYBOARD (DISPLAY)
SWITCH, KEYBOARD (FUNCTION)
SWITCH, KEYBOARD (TUNER/BAND)
1-671-617-11 PANEL-SW BOARD
**************
*
1-695-374-31 PIN, CONNECTOR (PC BOARD) 13P
1-695-372-31 PIN, CONNECTOR (PC BOARD) 11P
< SWITCH >
< DIODE >
DIODE
DIODE
DIODE
DIODE
DIODE
S699
D601
D602
D603
D604
D605
8-719-072-76
8-719-072-76
8-719-072-76
8-719-072-76
8-719-058-04
D606
8-719-056-13 DIODE SML72423C-TP4 (u)
Remark
**************************************************************
< CONNECTOR >
* CN601
CN603
Ref. No.
50V
50V
SEL5E23C-TP15 (±/))
SEL5E23C-TP15 (≠/0)
SEL5E23C-TP15 (π)
SEL5E23C-TP15 (fl)
SEL5223S-TP15 (t)
1-771-516-11 SWITCH, PUSH(DETECTION)(1 KEY)
**************************************************************
A-4419-068-A REG BOARD, COMPLETE
*******************
*
< FUSE >
! F941
! F942
< FLUORESCENT INDICATOR >
FL601
1-517-805-11 INDICATOR TUBE, FLUORESCENT
< CAPACITOR >
< IC >
IC601
IC602
1-532-465-31 FUSE (T3.15AL/250V)
1-532-465-31 FUSE (T3.15AL/250V)
8-759-572-22 IC MSM9202-02GS-KR1
8-759-459-85 IC NJL63H400A
C921
C922
C923
C924
C925
1-126-767-11
1-164-159-11
1-126-964-11
1-164-159-11
1-126-964-11
ELECT
CERAMIC
ELECT
CERAMIC
ELECT
1000uF
0.1uF
10uF
0.1uF
10uF
20%
C941
C942
C943
C944
C945
1-126-934-11
1-126-933-11
1-164-159-11
1-126-933-11
1-124-995-11
ELECT
ELECT
CERAMIC
ELECT
ELECT
220uF
100uF
0.1uF
100uF
220uF
20%
20%
C946
C947
C948
C949
C951
1-126-934-11
1-124-995-11
1-164-159-11
1-164-159-11
1-126-940-11
ELECT
ELECT
CERAMIC
CERAMIC
ELECT
220uF
220uF
0.1uF
0.1uF
330uF
20%
20%
C952
C953
C954
1-126-967-11 ELECT
1-164-159-11 CERAMIC
1-162-306-11 CERAMIC
47uF
0.1uF
0.01uF
20%
20%
20%
16V
50V
50V
50V
50V
< TRANSISTOR >
Q601
8-729-900-53 TRANSISTOR DTC114EK
< RESISTOR >
R601
R602
R603
R604
R605
1-216-025-91
1-216-025-91
1-216-025-91
1-216-025-91
1-249-437-11
RES,CHIP
RES,CHIP
RES,CHIP
RES,CHIP
CARBON
100
100
100
100
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/4W
R606
R607
R608
R609
R610
1-247-843-11
1-216-029-00
1-216-029-00
1-249-413-11
1-249-413-11
CARBON
METAL CHIP
METAL CHIP
CARBON
CARBON
3.3K
150
150
470
470
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/4W F
1/4W F
R611
R612
R613
R621
R622
1-249-411-11
1-216-029-00
1-216-029-00
1-249-413-11
1-249-415-11
CARBON
METAL CHIP
METAL CHIP
CARBON
CARBON
330
150
150
470
680
5%
5%
5%
5%
5%
1/4W
1/10W
1/10W
1/4W F
1/4W F
R623
R624
R631
R632
R633
1-249-417-11
1-249-419-11
1-249-413-11
1-249-415-11
1-249-417-11
CARBON
CARBON
CARBON
CARBON
CARBON
1K
1.5K
470
680
1K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/4W
20%
20%
20%
20%
16V
16V
50V
16V
10V
16V
10V
50V
50V
25V
50V
50V
16V
< CONNECTOR >
< SWITCH >
S621
1-762-875-21 SWITCH, KEYBOARD (§)
F
F
F
F
F
* CN942
CN943
CN944
CN945
1-564-522-11
1-770-405-11
1-770-405-11
1-506-481-11
PLUG, CONNECTOR 7P
CONNECTOR, BOARD TO BOARD 8P
CONNECTOR, BOARD TO BOARD 8P
PIN, CONNECTOR 2P
< DIODE >
D921
D922
D941
D942
D943
8-719-210-21
8-719-210-21
8-719-210-21
8-719-210-21
8-719-210-21
D944
8-719-210-21 DIODE 11EQS04
– 66 –
DIODE
DIODE
DIODE
DIODE
DIODE
11EQS04
11EQS04
11EQS04
11EQS04
11EQS04
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
REG
Ref. No.
D945
D946
D952
Part No.
Description
Remark
Ref. No.
8-719-986-04 DIODE HZS9A1LTA
8-719-986-04 DIODE HZS9A1LTA
8-719-986-26 DIODE HZS12A3LTA
< GROUND TERMINAL >
Part No.
SUB-TRANS
TRANS
Description
Remark
D962
D963
D964
8-719-024-99 DIODE 11ES2-NTA2B
8-719-024-99 DIODE 11ES2-NTA2B
8-719-024-99 DIODE 11ES2-NTA2B
D965
D966
8-719-986-67 DIODE HZS33-2LTA
8-719-921-37 DIODE MTZJ-4.7
EPT941 1-537-770-21 TERMINAL BOARD, GROUND
< IC >
< FUSE HOLDER >
IC901
FH941
FH942
FH943
FH944
1-533-293-11
1-533-293-11
1-533-293-11
1-533-293-11
FUSE HOLDER
FUSE HOLDER
FUSE HOLDER
FUSE HOLDER
< TRANSISTOR >
< IC >
IC921
IC922
8-759-231-53 IC TA7805S
8-759-373-82 IC TA7807SB
< TRANSISTOR >
Q941
Q942
Q943
Q951
Q952
8-729-140-96
8-729-040-20
8-729-029-66
8-729-202-67
8-729-026-68
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD774-34
RT1P137L-TP
DTC114ESA
2SK246-GR3
2SD2525(TP)
1-249-411-11 CARBON
1-247-843-11 CARBON
330
3.3K
Q901
Q961
Q962
Q963
Q964
8-729-029-66
8-729-118-01
8-729-040-19
8-729-040-19
8-729-040-19
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114ESA
2SB1116-K
RT1N137L-TP
RT1N137L-TP
RT1N137L-TP
Q965
Q966
8-729-029-21 TRANSISTOR DTA114ESA-TP
8-729-029-21 TRANSISTOR DTA114ESA-TP
< RESISTOR >
< RESISTOR >
R925
R941
8-759-373-79 IC TA7805SB
5%
5%
R901
! R961
R962
R964
R965
1-249-429-11
1-217-637-00
1-249-429-11
1-249-429-11
1-247-807-31
CARBON
FUSIBLE
CARBON
CARBON
CARBON
10K
1
10K
10K
100
5%
5%
5%
5%
5%
1/4W
1/4W F
1/4W
1/4W
1/4W
R966
R967
R968
R969
1-247-807-31
1-247-807-31
1-249-428-11
1-249-441-11
CARBON
CARBON
CARBON
CARBON
100
100
8.2K
100K
5%
5%
5%
5%
1/4W
1/4W
1/4W F
1/4W
1/4W
1/4W
< THERMISTOR(POSITIVE) >
THP941 1-801-671-11 THERMISTOR, POSITIVE
THP942 1-801-671-11 THERMISTOR, POSITIVE
< RELAY >
RY901
1-755-276-11 RELAY, POWER
**************************************************************
< TRANSFORMER >
A-4419-065-A SUB-TRANS BOARD, COMPLETE
*************************
*
! T901
< CAPACITOR >
**************************************************************
C901
C902
C903
C904
C962
1-126-935-11
1-126-933-11
1-113-925-11
1-164-159-11
1-128-576-11
ELECT
ELECT
CERAMIC
CERAMIC
ELECT
470uF
100uF
0.01uF
0.1uF
100uF
C963
C964
1-164-159-11 CERAMIC
1-126-948-11 ELECT
0.1uF
100uF
20%
20%
20%
20%
16V
16V
250V
50V
63V
20%
50V
35V
1-671-615-11 TRANS BOARD
***********
*
< CONNECTOR >
* CN991
* CN992
* CN994
< CONNECTOR >
* CN901
CN902
1-433-476-11 TRANSFORMER, POWER
1-564-687-11 PIN, CONNECTOR 3P
1-779-939-11 CONNECTOR, BOARD TO BOARD 7P
1-580-230-31 PIN, CONNECTOR (PC BOARD) 2P
1-568-226-11 PIN, CONNECTOR 2P
1-564-522-11 PLUG, CONNECTOR 7P
< FUSE >
! F991
1-532-465-31 FUSE (T3.15AL/250V)
< DIODE >
< DIODE >
D901
D902
D903
D904
D905
8-719-210-21
8-719-210-21
8-719-210-21
8-719-210-21
8-719-911-19
DIODE
DIODE
DIODE
DIODE
DIODE
11EQS04
11EQS04
11EQS04
11EQS04
1SS119-25
D906
D961
8-719-911-19 DIODE 1SS119-25
8-719-024-99 DIODE 11ES2-NTA2B
D951
D953
8-719-024-99 DIODE 11ES2-NTA2B
8-719-024-99 DIODE 11ES2-NTA2B
< FUSE HOLDER >
FH991
FH992
– 67 –
1-533-293-11 FUSE HOLDER
1-533-293-11 FUSE HOLDER
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
HCD-SD1
TRANS
Ref. No.
VOLUME
Part No.
Description
Remark
< THERMISTOR(POSITIVE) >
THP944 1-801-726-11 THERMISTOR, POSITIVE
THP945 1-801-726-11 THERMISTOR, POSITIVE
**************************************************************
1-671-610-11 VOLUME BOARD
************
*
< CAPACITOR >
C691
C692
1-162-306-11 CERAMIC
1-162-306-11 CERAMIC
0.01uF
0.01uF
20%
20%
16V
16V
< CONNECTOR >
* CLP691 1-690-880-31 LEAD (WITH CONNECTOR)
< SWITCH >
S691
1-418-012-11 ENCODER, ROTARY (VOLUME)
**************************************************************
MISCELLANEOUS
*************
15
16
53
54
! 57
1-769-940-11
1-769-972-11
1-790-305-11
1-693-408-11
1-575-651-91
WIRE (FLAT TYPE) (11 CORE)
WIRE (FLAT TYPE) (13 CORE)
WIRE (FLAT TYPE) (19 CORE)
TUNER
CORD, POWER
60
! 65
! 255
256
! CN904
1-773-108-11
1-770-019-11
8-848-379-31
1-769-069-11
1-526-794-11
WIRE (FLAT TYPE) (19 CORE)(100mm)
ADAPTOR, CONVERSION PLUG 3P (UK,HK)
OPTICAL PICK-UP KSS-213B/S-N
WIRE (FLAT TYPE) (16 CORE)
OUTLET, AC
FL601
M101
M102
M551
M904
1-517-805-11
X-4917-523-4
X-4917-504-1
1-698-997-21
A-4660-307-A
INDICATOR TUBE, FLUORESCENT
MOTOR ASSY (SPINDLE)
MOTOR ASSY (SLED)
FAN, D.C.
MOTOR (L) ASSY
! T991
1-433-478-11 TRANSFORMER, POWER
**************************************************************
*************
HARDWARE LIST
*************
#1
#2
#4
#5
#6
7-685-871-01
7-685-646-79
7-684-024-04
7-682-562-09
7-624-105-04
SCREW +BVTT 3X6 (S)
SCREW +BVTP 3X8 TYPE2 N-S
N 4, TYPE 2
SCREW +B 4X10
STOP RING 2.3, TYPE -E
#7
#8
7-685-234-19 SCREW +KTP 2.6X8 TYPE2NON-SLIT
7-621-775-10 SCREW +B 2.6X4
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
Sony Corporation
9-922-969-11
Home A&V Products Company
– 68 –
98L0953-1
Printed in Japan © 1998. 12
Published by Quality Assurance Dept.
(Shibaura)
Download PDF

advertising