Sony | SRX-R105CE | User's Manual | Sony SRX-R105CE User's Manual

Sony SRX-R105CE User's Manual
SXRD 4K Ultra High Resolution Projectors
SRX-R110CE / SRX-R105CE
SRX-S110 / SRX-S105
www.sonybiz.net/4k
Amazing 4K resolution images
for large-venue applications
2
Sony is proud to introduce a series of SXRD™ ultra
high-resolution projectors, which offer supreme
picture quality and reality for applications that require
highly sophisticated visuals. This state-of-the-art
Sony projector series, comprising the SRX-S110,
SRX-S105, SRX-R110CE, and SRX-R105CE models,
provides a new solution for applications such as
command & control, simulations, computer
visualisations, planetarium and museum exhibitions,
and much more.
Each model is equipped with three Silicon X-tal
Reflective Display (SXRD) imaging devices and
delivers an amazing resolution of 4096 x 2160 pixels
(H x V) – more than four times the resolution of HD
(1920 x 1080, 16:9 wide screen format).
The ultra high resolution capability enables a single
HD or 2K image to be internally up-converted by the
projector and displayed as a 4K image for a stunning
image. Aternatively the projector's multiple screen
mode allows full HD images to be displayed
simultaneously in four quadrants or in a twin
"side by side" display.
The projectors also offer a contrast ratio of more than
1800:1. In addition, the SRX-S110 and SRX-R110CE
models provide a high brightness of 10,000 ANSI
lumens*, while the SRX-S105 and SRX-R105CE
models offer a brightness of 5,000 ANSI lumens.
The use of twin Xenon lamps combined with multiple
gamma curves of 1.8, 2.2, and 2.6 means they offer
pure, high-quality colour tonal reproduction.
The SRX-S110 and SRX-S105 models – each
with one fixed DVI input module – have a 1080/60P
display capability available only with these units,
making them ideal for high-end computer graphicbased projection applications. On the other hand, the
SRX-R110CE and SRX-R105CE models – supplied
with one removable analogue input board– are more
suited to video-based projection applications.
Sony SXRD 4K projectors are the ultimate tool for
image display in a variety of critical applications from
high resolution visualisation systems to large-venue
projection.
is a measuring method of the American National Standards
* ANSI lumens
Institute
IT 7.228. Since there is no uniform method of measuring brightness,
specifications will vary among manufacturers.
3
State-of-the-art technology
for fantastic picture quality
Shown: ApolloWall-Pro from HoloVis (www.holovis.com)
Silicon X-tal Reflective Display (SXRD)
imaging device
The SXRD device used by the SRX-Series projectors is a 1.55-inch*
Liquid Crystal on Silicon based imager developed by Sony using
cutting-edge manufacturing technology. High-quality, accurate visuals
are created using this brilliant imaging device.
High 1800:1 contrast ratio
The SRX-Series projectors offer a high contrast ratio of more
than 1800:1* through the use of Sony’s unique SXRD device.
The SXRD imaging device itself achieves a contrast ratio of over
4000:1. This stunning picture quality makes the projectors ideal for
applications in which dynamic range is essential.
The high contrast ratio has been achieved through two key technologies – the exclusive ‘Vertically Aligned Liquid Crystal’ system and an
extremely thin liquid crystal cell gap.
*Measured diagonally.
*The contrast ratio is measured from a screen offering a gain of 1.0.
Vertically Aligned Liquid Crystal system
In every type of projector system, displaying absolute black is a major
issue in order to achieve a high contrast ratio. In other words, the contrast ratio of a projector depends on how effectively the light from the
source can be blocked so it does not leak through the imager.
4K resolution
Sony SXRD display devices deliver the exceptionally high resolution
of 4K (4096 H x 2160 V pixels at 1.896:1 aspect ratio), more than four
times as many pixels as full HDTV (1920 x 1080, 16:9 wide screen
format).
The SXRD device helps to achieve this resolution by incorporating
nearly 8.85 million pixels per imager at a narrow pitch of 8.5 micrometres. These high-density pixels, which are one quarter the size
of pixels projected using typical 2K resolution projection systems (2.2
million pixels), provide an amazing picture. Even in multi-screen mode,
full HD and 2K resolution per quadrant is possible. The resolution
available from the Sony SRX-Series projectors enables a new level of
visual projection.
2K
full HDTV
(1920 x 1080,
16:9 wide screen format)
(2048 H x 1080 V)
4K
(4096 H x 2160 V pixels at 1.896:1 aspect ratio)
State-of-the-art technology
4
All Liquid Crystal Display (LCD) devices control the amount of light to
be projected by applying an electric field to the liquid crystal gap. In
typical LCD devices, black is produced when an electric field is
applied across the liquid crystal cell gap. However molecules near the
surface of the glass substrate may not be accurately controlled due to
the influence of the alignment film. This is not an issue for bright
images. However, when displaying dark images, light may tend to leak
from the LCD device, since the molecules near the surface are less
accurately controlled. This results in a creamy black instead of a deep
black.
The SXRD device does not exhibit these characteristics. This is
because the Vertically Aligned Liquid Crystal system displays black
when the electric field is not applied. And because all molecules are
in the correct alignment, the polarised light alignment is also
optimised. The direct result is a far deeper black level, leading to a high
contrast ratio.
High-speed Image Display
Thin liquid crystal cell gap
Short response time
Another important contributing factor in the high contrast of the SXRD
projectors is the SXRD device’s ultra thin cell gap of less than
2 micrometres. With conventional Vertically Aligned Liquid Crystal systems, a thin cell gap could not be achieved. Sony has overcome this
difficulty through the use of innovative planarisation technology in the
silicon backplane structure and an advanced silicon wafer-based
assembly process.
The thin cell gap structure in SXRD devices also contributes to an
ultra-fast response time of 5 milliseconds. The SXRD device reacts
promptly to an instantaneous change of picture content, enabling
them to display a smooth motion.
The SXRD device also adopts a structure that does not use “spacers”.
These are columns found in conventional reflective liquid crystal
devices to maintain a constant gap between the liquid cell floor and
the top of the device. Spacers tend to both scatter and reflect light,
which can impair high contrast pictures. In the spacerless SXRD
device, these artifacts are no longer seen.
Consequently, the SRX-Series projectors virtually eliminate motion
blur. This is a particularly significant benefit for visuals that include
fast-moving objects.
Reliable imaging device
The SRX-Series projectors use high-power, bright lamps.
Consequently, special attention has been paid to the reliability of the
SXRD device. The inorganic materials utilised for the alignment layer
of the SXRD device are resistant to deterioration or deformities
that could occur due to the intense heat and light generated by the
powerful twin lamp system.
SXRD Cross-Section view
Light
Glass Substrate
Thin Cell Gap (2.0 µm) Space-less
• Short reponse time < 5 msec
• High Device Contrast ratio 4000:1
Inorganic Alignment Layer
• High reliability
Vertically Aligned
Liquid Crystal
Aluminium Pad
Silicon Backplane
Hight-Density Pixel Pitch 8.5 µm
• 4K x Full HD
(4096 H x 2160 V pixels)
Narrow Inter-Pixel
Spacing (0.35 µm)
• High fill factor 92 %
• High reflectivity
State-of-the-art technology
5
Highly pure, superb
colour tonal reproduction
Wide Colour Range
Xenon lamp provides highly bright and pure light
Colour Space Conversion (CSC) function
The SRX-S110 and SRX-R110CE models provide high brightness
of 10,000 ANSI lumens* from two 2kW Xenon lamps, while the
SRX-S105 and SRX-R105CE models offer brightness of 5,000 ANSI
lumens from two 1 kW Xenon lamps.
The SRX-Series projectors feature a CSC function to help users
easily adjust the projector’s colour space to that defined by either the
ITU*-R BT.709-3 standards for digital HDTV studio colour space, or
the new DCDM colour space.
The Xenon lamps in SRX-Series projectors achieve a wide colour
range by dispersing a very flat and wide light spectrum.
The latter is significantly wider than ITU 709 and takes advantage of
the spectrum emitted by the Xenon lamp. The target colour gamut
parameters satisfying the ITU-R BT. 709-3 standard or DCDM
specification are automatically calculated from settings on the
supplied SRX Controller software, and then applied to the projector.
The internal test generator simplifies adjustment and lets the operator
align the projector in minutes. White point and colour primary points
can be aligned to either of these standards or to the customer’s application needs.
*Measured under conditions with the lamp power at 100% in dual-lamp mode.
0.9
*International Telecommunication Union
0.8
Film
0.7
Xenon
0.6
TV
0.5
0.4
0.3
12-bit LCD driver
0.2
The SRX-Series projectors use a 12-bit imager driver to reproduce
extremely natural-looking images. This eliminates quantising and edge
errors that take away from the real resolution that these projectors can
achieve.
0.1
Gamma curve selection
0.0
0.1
0.2
0.3
0.4
0.5
CIE chart
Highly pure, superb colour tonal reproduction
6
0.6
0.7
0.8
The SRX-Series projectors provide three preset gamma curve values.
Users can select an optimum value from 1.8, 2.2, and 2.6 according
to the desired grey scale.
Operational
versatility
Dual-lamp system with selectable lamp modes
Zoom/Focus memory function
The SRX-Series projectors have a unique lamp system that uses
two lamps for reliable, flexible and efficient use of light sources. With
this system, users can operate the projector using both lamps for full
brightness or can select single lamp operations.
The SRX-Series projectors are equipped with Zoom and Focus
Memory functions that make it easy to switch the projection between
two types of aspect ratios. When used with the optional LKRL-Z117,
LKRL-Z119 and LKRL-Z122 Zoom Lenses, any seven zoom and
focus positions can be memorised and instantly recalled via the SRX
Controller software. This allows full screen display regardless of the
aspect ratio. An electronic vertical alignment feature is included in the
same memory to compensate for vertical changes in the image should
the projector be mounted at a down angle.
The dual-lamp mode provides maximum lamp power, and at the same
time enables virtually fail-safe operation; if one bulb burns out the
other continues to project images.
In the single-lamp mode, users can select either of the two lamps
manually, or the projector can automatically select a lamp based on
each lamp’s operating time. Another automatic mode is provided to
make the lamps operate
alternately at user-defined
intervals selectable from four
hours to twelve hours (in
increments of one hour).
This feature is useful for the
application where “24/7”
operation is required, but
lamp life needs to be maximised.
Multiple screen capability
The SRX-Series projectors provide single-mode, dual-mode and
quad-mode display. In quad mode, four quadrants of full 2K images
(2048 x 1080 pixels) can be projected simultaneously. The projector
can additionally internally up-convert a single HD or 2K input.
To obtain a 4K image of 4096 x 2160 pixels, 4 inputs of full 2K images
are input and stitched together internally in the projector.
The lamp power can be set
between 100 % and 51 %, in
eight steps. This function,
combined with the selectable
lamp modes, contributes to
achieving longer lamp life.
Single-mode
Variety of lenses
Four optional zoom lenses and a short throw prime lens are available
for the SRX-Series projectors. They are designed to project images of
extreme resolution and contrast with minimal chromatic aberration
from 1,829 mm to 15,497 mm in screen width. The short throw lens
works in special applications, such as rear projection, where minimal
space behind the screen is desired.
A
Dual-mode
Available lenses
LKRL-90: 0.9x fixed focal length projection lens
LKRL-Z115: 1.5 to 1.9x projection zoom lens
LKRL-Z117: 1.73 to 2.41x projection zoom lens
LKRL-Z119: 1.81 to 2.94x projection zoom lens
LKRL-Z122: 2.31 to 3.92x projection zoom lens
LKRL-Z140: 4.0 to 7.0x projection zoom lens
A
B
A
B
C
D
Quad-mode
Operational versatility
7
Option slots
LKRI-001
Analogue Input Board (Supplied
with SRX-R105CE/R110CE)
LKRI-002
HD-SDI (4:2:2) Input Board
LKRI-003
Dual-link HD-SDI Input Board
LKRI-004
DVI Interface Board
Input signal flexibility
To increase the configuration flexibility of the SRX-Series projectors,
slots are available to accommodate different optional boards that
connect to various types of signal format.
The SRX-S110 and SRX-S105 models are equipped with a DVI signal
input as standard, which provides the 1080/60P input capability
available only with these units.
In addition to the standard DVI input, three slots are available for
the installation of other optional input modules. Meanwhile, the
SRX-R110CE and SRX-R105CE models have four available slots for
even more flexible input configurations.
The SRX-R105CE and SRX-R110CE are supplied with one removable
LKRI-001 input board and the four option board slots can
accomodate any combination of input boards. Users can select the
screen mode from single, dual, and quad mode, and assign the
appropriate signal board to each quadrant.
• The LKRI-001 Analogue input board has 5 BNC connectors that
accept 0.7 volt analogue signal levels as RGBS, RGB sync on G,
RGBHV or YUV formats.
• The LKRI-002 HD-SDI (4:2:2) input board accepts both SMPTE
259M SD digital 525/625 line video and SMPTE 292M 1080 4:2:2
Y-Pb-Pr serial picture data. Switching is automatic by detection of
the input signal frequency.
• The LKRI-003 Dual-link HD-SDI input board accepts any of the
following signals: SMPTE 372M dual-link HD-SDI (4:4:4), SMPTE
292M HD-SDI (4:2:2), dual-link DC-SDI (RGB 4:4:4), DC-SDI (YPbPr
4:2:2), or 12-bit (X’Y’Z’ 4:4:4) signals. With four LKRI-003 boards,
the SRX-R110CE or SRX-R105CE can project 4096 x 2160 4K
images.
Operational versatility
8
• The LKRI-004 DVI interface board accepts DVI-D signals up to
2048 x 1080 and the following table illustrates the range of input
signals handled by each projector.
Resolution
SRX-S110/S105 SRX-R110CE/R105CE
Remarks
1
1024 x 768 at 60 Hz (XGA)
YES
YES
VESA
2
1280 x 960 at 60 Hz (SXGA)
YES
YES
VESA
3
1280 x 1024 at 60 Hz (SXGA)
YES
YES
VESA
4
1400 x 1050 at 60 Hz (SXGA+)
YES
YES
VESA
5
1600 x 1200 at 60 Hz (UXGA)
YES
YES
VESA
6
2048 x 1080 at 60 Hz
YES
NO
—
7
1920 x 1080 at 24 Hz
YES
YES
—
8
2048 x 1080 at 24 Hz
YES
YES
—
9
1920 x 1200 at 59.95 Hz Reduced Blanking (WUXGA)
YES
NO
VESA
10
1920 x 1080 at 60 Hz
YES
NO
EIA/CEA-861B
11
2048 x 1080 at 48 Hz
YES
YES
—
Simple Installation
SRX-Series projectors can be installed easily into almost any environment. Compared with conventional projectors in the ultra-high resolution class, they are highly compact and lightweight. Plus, their
power requirements are also reasonable – due to the use of singlephase power, which allows for remarkably low power consumption
and simpler installation.
To aid effective cooling, an optional exhaust duct adaptor is available,
which allows the projectors to be easily connected to a common
8-inch type duct system.
Large Venue Projection
Simple remote controller unit
Each SRX-Series projector is supplied with a remote controller unit that can perform various simple functions such
as turning the lamp power on/off, adjusting the
zoom/focus, and controlling the lens shift.
Easy setup on a PC using supplied software
The SRX-Series projectors come equipped with the SRX Controller
software that allows easy setup and adjustments via its intuitive GUIs
on a PC*. These projectors can be controlled through either Ethernet
or RS-232C interfaces, and multiple projectors can be controlled from
a single PC**. A comprehensive range of setup parameters including
input configurations, colorimetry controls, installation adjustments and
maintenance settings can be controlled via this software.
Installation
settings
®
* System requirements for the setup software OS: Microsoft Windows XP Professional.
PC is not supplied.
** When using an Ethernet connection.
Ethernet
PC
SRX-Series
Projector
SRX-Series
Projector
SRX-Series
Projector
Colorimetry
settings
RS-232C
PC
SRX-Series
Projector
Easy maintenance
Special consideration for maintenance issues was given in the
development of the SRX-Series projectors. The supplied setup
software is another convenient tool for maintenance. This allows operators to easily verify the lamps’ operating time. Automatic email alerts
from the projector provide operators with maintenance reminders as
well as error messages.
Maintenance
settings
Operational versatility
9
Dimensions
Unit=mm (inches)
1116 (44)
1326 (52 1⁄4)
357 (14 1⁄8)
167
(6 5⁄8)
740 (29 1⁄4)
320 (12 5⁄8)
498 (19 5⁄8)
500 (21 3⁄4)
754.5 (29 3⁄4)
395 (15 5⁄8)
Accessories
LKRL-90 Fixed Lens
LKRL-Z115 Zoom Lens
LKRL-Z117 Zoom Lens
LKRL-Z119 Zoom Lens
LKRL-Z122 Zoom Lens
0.9x Fixed Focal Length
Projection lens
1.5 to 1.9*x zoom lens
1.73 to 2.41x zoom lens
1.81 to 2.94x zoom lens
2.31 to 3.92x zoom lens
LKRI-004 DVI Interface Board
*The number denotes the ratio of the projection distance to the screen width.
10
LKRL-Z140 Zoom Lens
4.0 to 7.0x zoom lens
LKRI-001 Analogue Input
Board (Supplied with
SRX-R105CE/R110CE)
LKRI-002 HD-SDI (4:2:2)
LKRI-003 Dual-link HD-SDI
Input Board
Input Board
LKRX-105 1kW Xenon lamp
bulb for replacement
(for SRX-R105CE and SRX-S105)
LKRX-B105 1kW Xenon
lamp house unit
(for SRX-R105CE and SRX-S105)
LKRX-110 2kW Xenon lamp
bulb for replacement
(for SRX-R110CE and SRX-S110)
LKRX-B110 2kW Xenon
lamp house unit
(for SRX-R110CE and SRX-S110)
LKRA-001 8-inch Exhaust
Duct Adaptor
Specifications
Power requirements
AC 200 to 240 V, 50/60 Hz (SRX-R110CE/S110)
AC 100 to 240 V, 50/60 Hz (SRX-R105CE/S105)
Operating temperature
+5 ºC to +35 ºC (+41 ºF to +90 ºF)
Storage temperature
-20 ºC to +60 ºC (-4 ºF to +140 ºF)
Operating humidity
35 % to 85 % (without condensation)
Storage humidity
10 % to 90 %
Dimensions (W x H x D)
Approx. 740 x 500 x 1330mm
(29 4⁄5 x 19 4⁄5 x 52 3⁄5 inchs)
Mass
Approx. 110 kg (242 lb 8oz)
SXRD Device Main Specifications
Display device
SXRD (Silicon X-tal Reflective Display)
Size
1.55-inch across Diagonal
Resolution
4096(H) X 2160(V) Pixels
Reflectivity
72%
Contrast (as device)
More than 4000 : 1
Pixel pitch
8.5 µm
Width (between pixels)
0.35 µm
Response speed
5 msec (tr + tf)
Liquid crystal mode
Vertical Aligned Mode
Alignment layer
Inorganic Thin Film
Backplane process
0.35 µm MOS Process
Liquid crystal cell gap
Less than 2 µm
Input/Output
Input A
DVI-D interface board (SRX-S110/SRX-S105)
Open for optional signal interface board
(SRX-R110/SRX-R 105)
Input B
Open for optional signal interface board
Input C
Open for optional signal interface board
Input D
Open for optional signal interface board
Remote interface
D-sub 9-pin, RS-232C (female) x 1
Ethernet terminal, 10Base-T/100Base-TX x 1
Optical
Projection system
3-SXRD panel, prism colour integrated system
Imaging device
SXRD, 1.55-inch (diagonal), 4096(H) x 2160(V)
pixels on each chip
Lamp
2 kW Xenon lamp x 2 (SRX-R110CE)
1 kW Xenon lamp x 2 (SRX-R105CE)
Screen coverage
Approx. 4.5 m to 15.5 m (viewable area,
measured horizontally)
Light output
10,000 ANSI lumens ±10 % (SRX-R110CE/S110)*
5,000 ANSI lumens ±10 % (SRX-R105CE/S105)
Input Boards
LKRI-001
Analogue input board
BNC x 5, HD/SD analogue video input,
RGB/Y • Cb • Cr selectable
Computer signals
R: 0.7 Vp-p ±2 dB positive, 75 Ω
G: 0.7 Vp-p ±2 dB positive, 75 Ω
B: 0.7 Vp-p ±2 dB positive, 75 Ω
Sync
HD Horizontal: TTL level, high impedance,
sync positive/negative
HD Vertical: TTL level, high impedance,
sync positive/negative
Standard definition video (Y • Cb • Cr)
Y; 1.0 Vp-p ±2 dB sync negative, 75 Ω
Cb: 0.7 Vp-p ±2 dB positive, 75 Ω
Cr: 0.7 Vp-p ±2 dB positive, 75 Ω
High definition video (RGB)
R: 0.7 Vp-p ±2 dB positive, 75 Ω
G: with sync 1.0 Vp-p ±2 dB, 75 Ω,
Tri-level sync: ±0.3 Vp-p / Bi-level sync: 0.3 Vp-p
B: 0.7 Vp-p ±2 dB positive, 75 Ω
High definition video (Y • Pb • Pr)
Y: 1.0 Vp-p ±2 dB, 75 Ω,
Tri-level sync: ±0.3 Vp-p / Bi-level sync: 0.3 Vp-p
Pb: ±0.35 Vp-p ±2 dB, positive 75 Ω
Pr: ±0.35 Vp-p ±2 dB, positive 75 Ω
LKRI-002 HD-SDI (4:2:2) input board
BNC x 2 (Input x 1,Loop-through out x 1)
HD-SDI (SMPTE-292M / ITU-R.BT709 / BTA-S004)
SDI (SMPTE-259M / ITU-R.BT601)
General
White reference
Xenon white reference
White reference
Y: 0.3510 / X: 0.3140
Contrast
more than 1800:1
Resolution
600 TV lines (SDI input/SMPTE-259M)
1920 x 1080 pixels (HD-SDI input, SMPTE-292M)
4096 x 2160 pixels (RGB)
Signal specifications
SRX-S110 / SRX-S105
Video:
Component (Y • Cb • Cr),
HD (G • B • R/Y • Pb • Pr)
Computer: XGA, SXGA, UXGA
DVI-D: XGA, Quad-VGA, SXGA, UXGA,
WUXGA, 1920 x 1080, 2048 x 1080
SRX-R110CE / SRX-R105CE
Video:
Component (Y • Cb • Cr),
HD (G • B • R/Y • Pb • Pr)
Computer: XGA, SXGA, UXGA
LKRI-003 Dual-link HD-SDI input board
BNC x 4 (Input x 2,Loop-through out x 2)
HD-SDI (Single-link, HD-SDI/4:2:2,SMPTE292M):Y • Pb • Pr,
DC-SDI (Single-link, DC-SDI/4:2:2):Y • Pb • Pr,
Dual-link HD-SDI (Dual-link HD-SDI/4:4:4,
SMPTE-372M):RGB,
Dual-link DC-SDI (Dual-link DC-SDI/4:4:4):RGB
LKRI-004 DVI Interface Board
SRX-S110/SRX-S105:
1024 x 768 at 60 Hz (XGA),
1280 x 960 at 60 Hz (SXGA),
1280 x1024 at 60 Hz(SXGA),
1400 x 1050 at 60 Hz (SXGA+),
1600 x 1200 at 60 Hz (UXGA),
2048 x 1080 at 60 Hz,
1920 x 1080 at 24 Hz,
2048 x 1080 at 24 Hz,
1920 x 1200 at 59.95 Hz Reduced Blanking (WUXGA)
1920 x 1080 at 60 Hz,
2048 x 1080 at 48 Hz
SRX-R110/SRX-R105:
1024 x 768 at 60 Hz (XGA),
1280 x 960 at 60Hz (SXGA),
1280 x 1024 at 60 Hz (SXGA),
1400 x 1050 at 60 Hz (SXGA+),
1600 x 1200 at 60 Hz (UXGA),
1920 x 1080 at 24 Hz,
2048 x 1080 at 24 Hz
Others
Safety regulations
(UL60950 listed), (cUL60950), (FCC Class A), (IC
Class A), (VCCI Class A), (EN60950), (CE Class A),
(C-tick), (GB4943), (GB9254), (K60950),
(CISPR22), (CISPR24)
Supplied Accessories
Remote controller x 1
CD-ROM x 1 (Remote control application for
Windows® XP Professional Edition)
Dry cell (AA size) x 2
Ethernet Cross Cable (3 m) x 1
Operation instructions x 1 (SRX-S110/SRX-S105)
Installation manual x 1 (SRX-R110/SRX-R105)
Optional Accessories
LKRL-90: 0.9x Fixed Focal Length Projection lens
LKRL-Z115: 1.5 to 1.9x zoom lens
LKRL-Z117: 1.73 to 2.41x zoom lens
LKRL-Z119: 1.81 to 2.94x zoom lens
LKRL-Z122: 2.31 to 3.92x zoom lens
LKRL-Z140: 4.0 to 7.0x zoom lens
LKRI-001: Analogue input board
LKRI-002: HD-SDI (4:2:2) input board
LKRI-003: Dual-link HD-SDI input board
LKRI-004: DVI interface board
LKRX-105: 1kW Xenon lamp bulb for replacement
(for SRX-R105CE)
LKRX-B105: 1kW Xenon lamp house unit for
replacement (for SRX-R105CE)
LKRX-110: 2kW Xenon lamp bulb for replacement
(for SRX-R110CE)
LKRX-B110: 2kW Xenon lamp house unit for
replacement (for SRX-R110CE)
LKRA-001: 8-inch Exhaust Duct adaptor
Preset Data of Input Signals
No Signal Number
0
3
4
5
23
24
25
26
32
33
36
37
NO INPUT
VIDEO 60 (480 60i)
VIDEO 50 (575 50i)
HDTV (1080 60i)
1024 x 768 VESA60
1024 x 768 VESA70
1024 x 768 VESA75
1024 x 768 VESA85
1280 x 960 VESA60
1280 x 960 VESA75
1280 x 1024 VESA60
1280 x 1024 VESA75
fH
0
15.73
15.63
33.75
48.36
56.48
60.02
68.68
60.00
75.00
63.97
79.98
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
fV
0
59.94
50.00
60.00
60.00
70.07
75.03
85.00
60.00
75.00
60.01
75.03
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
Aspect Horizontal Vertical
Sampling Sampling
4:3
4:3
16:9
4:3
4:3
4:3
4:3
4:3
4:3
5:4
5:4
1280
1280
1920
1024
1024
1024
1024
1280
1280
1280
1280
480
570
1080
768
768
768
768
960
960
1024
1024
No Signal Name
38
39
45
47
48
49
(75)
(76)
(77)
1280 x 1024 VESA85
1600 x 1200 VESA60
1080 50i
720 60P
720 50P
1080 48I (24PsF)
1080 60i
1080 25PsF
1080 30PsF
fH
91.15
75.00
31.25
45.00
37.50
27.00
33.75
31.25
33.75
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
fV
85.02
60.00
50.00
60.00
50.00
48.00
60.00
50.00
60.00
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
kHz
Aspect Horizontal
Sampling
5:4
1280
4:3
1600
16:9 1920
16:9 1280
16:9 1280
16:9 1920
16:9 1920
16:9 1920
16:9 1920
Vertical
Sampling
1024
1200
1080
720
720
1080
1080
1080
1080
Note:
* When a signal other than the preset signals shown above is fed into this projector, the images may not
be projected properly.
11
© 2007 Sony Corporation. All rights reserved. Reproduction in whole
or in part without permission is prohibited. Features and specifications
are subject to change without notice. All non-metric weights
and measurements are approximate. Sony, CineAlta 4K, SXRD,
and SXRD logo are trademarks of Sony Corporation. Windows
is a registered trademark of Microsoft Corporation. Pentium is a
registered trademark of Intel Corporation.
CA SRX-Series/GB- / /2007
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising