System Components
All Systems
One 9 volt battery
PG4 or PG88 Receiver
Internal Diversity Antenna System
AC Power supply User guide
Vocalist System
Microphone Head PG2 handheld transmitter
Instrument System
PG1 bodypack transmitter
Microphone clip
4-pin mini connector (TA4F) to
1/4” connector cable
Lavalier and Headworn System
PG1 bodypack transmitter
Microphone (choice of PG185, PG30)
Replacement Parts
All Systems Microphone Stand Adapter (PGX2)
System-Specific AC Adapter (120 VAC, 60 Hz)
AC Adapter 220 VAC, 50 Hz), Argentina
WA371
PS20
PS20AR
AC Adapter (230 VAC, 50/60 Hz, Europlug) PS20E
AC Adapter (230 VAC, 50/60 Hz, UK)
AC Adapter (100 VAC, 50/60 Hz)
PS20UK
PS20J
AC Adapter (220 VAC, 50 Hz, China)
AC Adapter (230 VAC, 50 Hz,, Australia)
AC Adapter (220 VAC, 60 Hz, Korea
PS20CHN
PS20AZ
PS20K
Optional
PG58 Head with Grille
Belt Clip
Universal Rack Tray
4-pin mini connector (TA4F) to 1/4” connector cable
RPW108
44A8035
URT
WA302
Technical Specifications
System
Working Range 75m (250 ft.) Note: actual range depends on RF signal absorption, reflection, and interference.
Audio Channel Response Minimum: 45 Hz.
Maximum: 15 kHz (overall system channel depends on microphone element).
Total Harmonic Distortion 0.5%, typical
Ref. +/– 33 kHz deviation, 1 kHz tone
Dynamic Range >100 dB A-weighted, typical
Operating Temperature
Range
–18°C (0°F) to +57°C (+135°F)
Note: battery characteristics may limit this range
Transmitter Audio Polarity Positive pressure on microphone diaphragm (or positive voltage to tip of
WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3 of low impedance output) and the tip of the high impedance 1/4-inch output.
PG1 Bodypack Transmitter
Audio Input Level
Gain Adjustment Range
Input Impedance
RF Transmitter Output
Dimensions
Weight
Housing
Power Requirements
Battery Life
–10 dBV maximum at “mic” gain position
+10 dBV maximum at 0dB gain position
+20 dBV maximum at –10dB gain position
30 dB
1mΩ
10 mW typical (dependent on applicable country regulations)
110 mm H x 64 mm W x 21 mm D (4.3 x 2.5 x 0.8 in.)
75 grams (2.6 oz.) without battery
Molded ABS
One 9V alkaline or rechargeable battery
>8 hours (alkaline)
PG2 Handheld Transmitter
Audio Input Level
Gain Adjustment Range
RF Transmitter Output
Dimensions
Weight
Housing
Power Requirements
Battery Life
+2 dBV maximum at –10dB position
–8 dBV maximum at 0dB position
10dB
10 mW typical (dependent on applicable country regulations)
223.52 L x 53.34 Dia. (8.8 in. x 2.10 in.)
218 grams (7.7 oz.) without battery
Molded ABS handle and battery cup
One 9V alkaline or rechargeable battery
>8 hours (alkaline)
Technical Specifications cont’d
PG4 and PG88 Receiver
Output Impedance XLR connector: 200 Ω 1/4 inch connector: 1kΩ
Audio Output Level Ref.
+/– 33 kHz deviation with
1 kHz tone
Sensitivity
Image Rejection
Dimensions
Dimensions - PG88
Weight
Weight - PG88
XLR connector (into 100K Ω load): –19 dBV, typical
1/4 inch connector (into 100K Ω load): –5 dBV, typical
–105 dBm for 12 dB SINAD, typical
>50 dB, typical
188 mm L x 103 mm W x 40 mm D (7.4 in. x 4.0 in. x 1.5 in.)
388 mm L x 116 mm W x 40 mm D (15.3 in. x 4 in. x 1.5 in.)
241 grams (8.5 oz)
429 grams (15.1 oz)
Housing Molded ABS
Power Requirements 12–18 Vdc at 160 mA (PG4), 320mA (PG88), supplied by external power supply
Regulatory Information
Regulatory Information for North America, Europe, and Australia
PG1 & PG2 Transmitters: Certified to FCC Part 74 (FCC ID: “DD4PG1” and “DD4PG2”).
Certified by IC in Canada under RSS-123 and RSS-102 (“IC: 616A-PG1” and “IC: 616A-
PG2”). Meets the essential requirements of the European R&TTE Directive 99/5/EC (ETSI EN
300-422 Parts 1 & 2, EN 301 489 Parts 1 & 9) and are eligible to carry the CE marking.
PG4 and PG88 Receiver: Authorized under Declaration of Conformity (DoC) provision of
0978 !
FCC Part 15. Certified under Industry Canada to RSS-123 (“IC: 616A-PG4”). This class B digital apparatus complies with Canadian ICES-003. Meets the essential requirements of the
European R&TTE Directive 99/5/ EC (EN 301 489 Parts 1 & 9, EN 300 422 Parts 1 & 2) and is eligible to carry the CE marking. Conforms to Australian EMC requirements and is eligible for C-Tick marking.
NOTE: This equipment has been tested and found to comply with the limits for a Class
N108
Z540
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio channel energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Caution
Changes or modifications not expressly approved by Shure Incorporated for compliance could void the user’s authority to operate the equipment. Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Patents
Patent numbers 6,597,301 and 6,296,565
PS20 Series Power Supplies: Conform to Safety Standard IEC 60065.
PS20E and PS20UK are eligible to bear CE marking.
A ministerial license may be required to operate this equipment in certain areas. Consult your national authority for possible requirements.
This radio equipment is intended for use in musical professional entertainment and similar applications.
SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414
Asia, Pacific:
Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055
