TE-LPC TE-LPC - iBEAM, Vehicle Safety Systems

TE-LPC TE-LPC - iBEAM, Vehicle Safety Systems
TE-LPC
Product Manual
800.221.0932
iBeamUSA.com
460 Walker Street, Holly Hill, FL 32117
TE-LPC
Product Manual
800.221.0932
iBeamUSA.com
460 Walker Street, Holly Hill, FL 32117
I. Specifications
II. Connection
Parking line loop (White)
SENSOR
CMOS II
Effective Pixel
656 X 492
Reverse Lights
RED (+)
BLACK (Ground)
TV
Red (Reverse Switch)
Reverse Wire on Radio (Trigger)
Reverse image loop (Blue)
Horizontal Sync Frequency
15625KHZ
Vertical Sync Frequency
PAL50HZ / NTSC 60HZ
Scanning System
2 : 1 Interlace
Sync System
Internal
AGC
Auto
BLC
Auto
Resolution
420 TV Lines
S/N Ratio
More Than 48dB
4) Connect the BLACK wire to ground (a metal, non-painted surface).
Current Consumption
No More 150mA
5) Run video cable though vehicle, up to video display. (Avoid placing video
cable where it can get pinched or damaged).
Power Supply
DC12V ± 10%
Operating Temperature
-22°
Video (in)
1) Find a suitable location to surface mount install the camera. Make sure the
camera’s view is unobstructed and be careful not to drill into any wires that
might damage the vehicle, insure you have enough depth and accessibility to
attach the supplied nut on the post to secure the camera. When all connections
have been made and before mounting the camera, verify the camera is working
and has good view of the area.
2) Treaded post should be installed in the upward position. Use a 3/8” bit to drill
a hole for surface mounting of camera, then install camera.
Storage Tempurature
~
-40° ~ 176° F
Viewing Angle
170°
Water-Proof
IP67
Minimum Illumination
0.5Lux/F1.2(0Lux with LED)
176° F
3) Connect the RED wire to the +12 volt reverse wire
6) A
ttach the YELLOW video rca to the reverse camera input of the radio or
video display; connect the RED wire coming from the YELLOW video rca to
the reverse trigger wire on the radio or video display.
NOTE: The camera comes with the parking assist lines and a normal image view
active. If you want to remove the parking lines or change the image to reverse
image, follow the steps below:
A) Disconnect power to the camera
B) Cut the WHITE loop to remove the parking assist lines, isolate and tape the wires
C) Cut the BLUE loop to reverse the image, isolate and tape the wires
D) Reconnect power to the camera
If the parking assist lines are wanted or the image needs to go back to normal,
just follow the steps above and reconnect the wires.
I. Specifications
II. Connection
Parking line loop (White)
SENSOR
CMOS II
Effective Pixel
656 X 492
Reverse Lights
RED (+)
BLACK (Ground)
Red (Reverse Switch)
Reverse Wire on Radio (Trigger)
Reverse image loop (Blue)
TV
Video (in)
Horizontal Sync Frequency
15625KHZ
Vertical Sync Frequency
PAL50HZ / NTSC 60HZ
Scanning System
2 : 1 Interlace
Sync System
Internal
AGC
Auto
BLC
Auto
Resolution
420 TV Lines
S/N Ratio
More Than 48dB
4) Connect the BLACK wire to ground (a metal, non-painted surface).
Current Consumption
No More 150mA
5) Run video cable though vehicle, up to video display. (Avoid placing video
cable where it can get pinched or damaged).
Power Supply
DC12V ± 10%
Operating Temperature
-22°
Storage Tempurature
~ 176° F
-40° ~ 176° F
Viewing Angle
170°
Water-Proof
IP67
Minimum Illumination
0.5Lux/F1.2(0Lux with LED)
1) Find a suitable location to surface mount install the camera. Make sure the
camera’s view is unobstructed and be careful not to drill into any wires that
might damage the vehicle, insure you have enough depth and accessibility to
attach the supplied nut on the post to secure the camera. When all connections
have been made and before mounting the camera, verify the camera is working
and has good view of the area.
2) Treaded post should be installed in the upward position. Use a 3/8” bit to drill
a hole for surface mounting of camera, then install camera.
3) Connect the RED wire to the +12 volt reverse wire
6) A
ttach the YELLOW video rca to the reverse camera input of the radio or
video display; connect the RED wire coming from the YELLOW video rca to
the reverse trigger wire on the radio or video display.
NOTE: The camera comes with the parking assist lines and a normal image view
active. If you want to remove the parking lines or change the image to reverse
image, follow the steps below:
A) Disconnect power to the camera
B) Cut the WHITE loop to remove the parking assist lines, isolate and tape the wires
C) Cut the BLUE loop to reverse the image, isolate and tape the wires
D) Reconnect power to the camera
If the parking assist lines are wanted or the image needs to go back to normal,
just follow the steps above and reconnect the wires.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising