User Guide - Produkcija. Euro Baltronics

User Guide - Produkcija. Euro Baltronics
Technical Specifications
Power
AC 120V~60Hz
AC 230/240/250V~50/60Hz
Fuse
20mm Glass 6.3A Fast Blow
20mm Glass 5A Fast Blow
Lamp
ELC 24V 250W
Dimension
290mm x 330mm x 380mm
Weight
12 kg
BEGLEC CVA
‘t Hofveld 2 – B1702 Groot-Bijgaarden
WWW.BEGLEC.COM
Innovation , Quality , Performance
IMOVE-5S
IMOVE-5W
User Guide
Professional Entertainment Technology
7. Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater
accumulation of dirt on the unit’s optics.
y Clean with soft cloth using normal glass cleaning fluid.
y Always dry the parts carefully.
y Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
EC Declaration of Conformity
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
2A
EN55014-1: 1993, EN61000-3-2: 1995, EN61000-3-3:1995
EN55014-2: 1997 CATEGORY II
EN61000-4-2: 1995, EN61000-4-3: 1995, EN61000-4-4:1995
EN61000-4-5: 1995, EN61000-4-6: 1995, EN61000-4-11: 1994
&
Harmonized Standard
EN60598-1: 1993
Safety of household and similar electrical appliances
Part 1 : General requirements
Following the provisions of the Low Voltage Directive 73/23/EEC and 93/68/EEC.
EC Declaration of Conformity
We declare that our products (remote controller) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55015: 1993
EN50082-1: 1997
EN61000-3-2: 1995
EN61000-3-3: 1995
.
.
G. If The pan belt is broken
1. Turn off the main power.
2. Unscrew all the screws (A) and open the base-housing cover (B).
TABLE OF CONTENTS
3. Unplug all the connect wires (C) that from the arm to PC board and ignitor.
1. Safety Instruction
4. Unscrew the screws (D) that fix the axis gear (E).
5. Change a new belt (F) by going through all connect wires that from the arm to base,
2. Technical Specification
and through the bridge for correct position.
2.1 Beam Angel
6. Set up the gear axis to the bridge and screwed it. Note : do not press the belt.
3. Lamp
7. Put the belt around the axis gear and motor gear.
8. Plug all the connect wires (C) that form the arm to PC board and ignitor.
4. How To Set The Unit
9. Adjust the pan home position.
4.1 Control Panel
10. Screw the base-housing cover (B).
4.2 Main Function
3A
5. How To Control The Unit
5.1 Master/Slave Built-In Preprogrammed Function.
5.2 Easy Controller
5.3 iSolution Operation / Universal DMX Controller
5.4 DMX512 Configuration
5.5 DMX512 Connection
6. Troubleshooting
7. Fixture Cleaning
1. Safety Instruction
shock.
Please read carefully the instruction, which includes important information
6. Troubleshooting
about the installation, usage and maintenance.maintenance.
WARNING
Following are a few common problems that may occur during operation. Here are
♦
some suggestions for easy troubleshooting:
Please keep this User Guide for future consultation. If you sell the unit to another user,
be sure that they also receive this instruction booklet
♦
Unpack and check carefully there is no transportation damage before using the unit.
♦
Before operating, ensure that the voltage and frequency of power supply match the
1. Check the connection of power and main fuse.
power requirements of the unit.
2. Measure the mains voltage on the main connector.
The unit is designed for use with the ELC 24V 250W. Do not use any other type of
3. Check the power on LED.
♦
A. The unit does not work, no light and the fan does not work
lamp.
♦
♦
♦
B. Not responding to DMX controller
It’s important to ground the yellow/green conductor to earth in order to avoid electric
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
shock.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
The unit is for indoor use only. Use only in a dry location.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
♦
Disconnect main power before fuse/lamp replacement or servicing.
♦
Replace fuse/lamp only with the same type.
♦
Make sure there is no flammable materials close to the unit while operating as it is fire
hazard.
♦
Use safety cable when fixes this unit. Don’t handle the unit by taking its head only, but
always by taking its base.
♦
Maximum ambient temperature is TA: 40℃. Don’t operate it where the temperature is
higher than this.
♦
♦
Unit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand
of the unit or the previous one.
4A
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may
cause damage or interference to DMX interface circuit.
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the
master/ slave mode signal.
2. Wrong DMX address in the unit. Set the proper address.
D. No response to the sound
1. Make sure the unit does not receive DMX signal.
2. Check microphone to see if it is good by tapping the microphone
E. One of the channels is not working well
during its operation. Turn off the power and allow about 15 minutes for the unit to cool
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
down before replacing bulb or serving.
2. The motor’s drive IC on the PCB might be out of condition.
In the event of serious operating problem, stop using the unit immediately. Never try to
F. The lamp is cutting out intermittently
repair the unit by yourself. Repairs carried out by unskilled people can lead to damage
1. The lamp is not working well. Check the main voltage either too high or too low.
or malfunction. Please contact the nearest authorized technical assistance center.
2. Internal temperature may be too high. Check and if necessary replace the fan on the
Always use the same type spare parts.
♦
Don’t connect the device to any dimmer pack or power pack.
♦
Do not touch any wire during operation as high voltage might be causing electric
head.
.
5.5 DMX512 Connection
The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.
1
2
3
Warning
4
♦
To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
♦
Never touch bulb with bare fingers as it is very hot after using.
♦
Hot lamp explosion hazard. Do not open the unit within five minutes after switching off.
♦
Do not start on the unit without bulb enclosure or housing are damaged.
♦
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
COMMON
DMX512
1
INPUT
3
2
DMX +
DMX -
♦
120 ohm 1/4W
Do not look directly at the light while the bulb is on.
1
3
OUTPUT
Caution
2
Termination reduces signal errors and to avoid signal
transmission problems and interference. It is always
advisable to connect a DMX terminal.
(Resistance 120 ohm 1/4W) between pin2 (DMX-) and
pin3 (DMX+) of the last fixture.
There are no user serviceable parts inside the unit. Do not open the housing or attempt
3
adapter-cable.
2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in
the DMX-output of the last unit.
3. Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to the
input of the next unit. The cable can not branched or split to a `Y` cable. DMX512 is a
very high-speed signal. Inadequate or damaged cables, soldered joints or corroded
connectors can easily distort the signal and shut down the system.
4. The DMX output and input connectors are pass-through to maintain the DMX circuit,
when power is disconnected to the unit.
5. Each lighting unit needs to have an address set to receive the data sent by the controller.
6. The end of the DMX512 system should be terminated to reduce signal errors.
7. 3 pin XLR connectors are more popular than 5 pin XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
your nearest dealer.
2
1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin
The address number is between 0-511 (usually 0 & 1 are equal to 1).
any repairs yourself. In the unlikely event your unit may require service, please contact
1
5A
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the
unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
structure to which you are attaching the unit is secure and is able to support a weight of
20 kgs for each unit
2. Technical Specification
• Voltage:AC 120V~60Hz or 230V/240V/250V~50/60Hz
• Bulb:ELC 24V 250W
• The unit is DMX512 fixture. It features full DMX512 control. It can be also linked together
in master/slave connection, as many as required and run by built-in program chase
sequences automatically or by sound activation through an internal microphone to create
an intelligent effect.
• It can be operated by DMX512 control or can be used as an individual unit without a
controller.
• Consistent DMX channel enable iRock, iShow and iMove to be link together.
• Features different preprogrammed chase patterns.
• Please use a 3 pin XLR cable/plug when connecting units together.
• Accurate focusable optics system and ultra smooth stepping motors. Fan cooling.
• Pan : 540 deg. Tilt : 270 deg.
• Dimension : 290 x 330 x 380 mm
• Weight : 12 kg
IM-5S Independent gobo wheel with 14 gobos plus open and blackout, including 10 metal, 1
replaceable gobo, 2 glass and 1 effect gobos with shaking and shutter effect,
Independent color wheel with 11 dichroic colors with rainbow effect.
IM-5W Independent color wheel with 11 dichroic colors with rainbow effect and independent
shutter & dimmer.
2.1 Beam Angel
6A
5.4 DMX512 Configuration
IM-5S
Stand by
X/Y moving show mode Color/Gobo selection
Strobe
1. Hold on for gobo
1.Gobo/Color sync selection
( Show 1 ~ Show 4 )
change.
strobe
Please refer to Show mode 2. Press shortly for
2.Sync. strobe
in 4.2 Main Function..
color change.
3.Two-light strobe
X/Y moving setting
1.Pan position
2.Tilt position
First set Master unit,
then set Slave units’
position.
Mode
Sound 1
(LED off )
Position/ Latch
(LED fast blinking)
Stand by
Blackout the unit
Function
IM-5W
Blackout the unit
Function
Mode
Sound 2
(LED normal blinking)
Slow/Sound 3
(LED on)
X/Y moving show mode Color selection
Strobe
1.Gobo/Color sync selection
strobe
( Show 1 ~ Show 4 )
2.Sync. strobe
Please refer to Show mode
3.Two-light strobe
in 4.2 Main Function..
X/Y moving setting
1.Pan position
2.Tilt position
3.Dimmer
First set Master unit,
then set Slave units’
position.
Sound 1
(LED off )
Position/ Latch
(LED fast blinking)
Sound 2
(LED normal blinking)
Slow/Sound 3
(LED on)
5.3.1 iSolution Operation
♦
7A
Consistent DMX configuration enable iMove to be linked together with iRock and iShow
and controlled at the same time.
♦
DMX address can be set remotely by iLead controller ( please refer to the user manual
of iLead controller ). No need to calculate the DMX channels of each fixture in the chain.
♦
Automatic switching between DMX function and built-in stand alone programs.
5.3.2 DMX Controller
If you use a universal DMX controller to control the units, you have to set DMX address from
1 to 512 channel so that the units can receive DMX signal.
Press the MENU button up to when the
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press and keep ENTER button pressed up to when
the display stops blinking or storing automatically 8 seconds later. To go back to the
functions without any change press the MENU button again. Please refer to the following
diagram to address your DMX512 channel for the first 4 units.
DMX address can be setting remotely by IL-0824 controller. No need to calculate the DMX
Ch 1
Ch 2
Ch 3
Ch 4
Ch 5
IM-5S
Pan
Tilt
Shutter/Sharking
Gobo
Color
IM-5W
Pan
Tilt
Shutter
No function
Color
Ch 6
Ch 7
No function
Dimmer
channels of each fixture in the chain.
3. Lamp
4. How To Set The Unit
In case of replacement of the lamp or maintenance, do not open the
4.1 Control Panel
fixture within 15 minutes until the unit cools down after switching off.
Lamp :
ELC 24V 250W
1. Always switch off the main supply and never handle the lamp or luminaries when is
hot.
2. Do not touch the bulb with bare hands. If this happens, clean the lamp with denatured
alcohol and wipe it with a lint free cloth before installation.
Display
3. Never operate the lamp without appropriate shielding.
To show the various menus and the selected functions.
4. Make sure the lamp is located in the center for the best spot.
LED
Diagram for Lamp changing
8A
DMX
MASTER
SLAVE
SOUND
On
On
On
Flashing
DMX input present
Master Mode
Slave Mode
Sound activation
MENU
DOWN
UP
ENTER
To select the programming functions
To go backward in the selected functions
To go forward in the selected functions
To confirm the selected functions
Button
Remote controller input
By connect to the 1/4” microphone jack to control the unit for stand by, function and mode
Sensitivity
To adjust the sound sensitivity.
Microphone
To receive audio signal for sound activation.
DMX input/output
For DMX512 link, use 3-pin XLR plug cable to link the unit together.
5. How To Control The Unit
Display Inversion
You can operate the unit in three ways:
It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to
1. By master/slave built-in preprogram function
when the
2. By easy controller
is blinking on the display. Use the ENTER button to change to the mode
(display inversion), It will automatically store after 8 seconds. Or press the ENTER
3. By iLead controller ( please refer to the user guide of iLead ) or universal DMX
button again return to the mode
the MENU button again.
controller
(display normal). To go back to the functions press
No need to turn the unit off when you change the DMX address, as new DMX address
Display normal mode for the fixture putting on the floor.
setting will be effected at once. Every time you turn the unit on, it will show IM-5S/IM-5W on
Display inversion mode for the fixture fixing under ceiling.
the display and move all the motors to their ‘home’ position and you may hear some noises
for about 20 seconds. After that the unit will be ready to receive DMX signal or run the built
Focus Adjust
in programs.
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button, the unit will focus on tilt 90°, and then the unit will focus on pan 0°, pan 90°, pan180°,
5.1 Master/Slave Built In Preprogrammed Function
pan270° in every pressing ENTER button. To go back to the functions press the MENU
button again.
By linking the units in master/slave connection, the first unit will control the other units to
give an automatic, sound activated, synchronized light show. This function is good when you
and select
want an instant show. You have to set the first unit in master mode
(show 1) or
(show 2) or
(show 3) or
(show 4) mode. Its
DMX input jack will have nothing plugged into it, and Its master LED will be constantly on
and sound LED will flash to the music. The other units will have to set in slave mode
(normal) or
(2 light show) mode, Their DMX cables plugged into
and select
the DMX input jacks (daisy chain) and the slave led lights will constantly on.
9A
Self-Test
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and the unit will run self-test by built in program. To go back to the functions press the
MENU button again.
2-light show
Fixture Hours
In
(slave mode),
means the unit works normally and
means
on the second unit to
2-light show. In order to create a great light show, you can set
get contrast movement to each other, even if you have two units only.
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and the display will show the number of working hours of the unit. To go back to the
functions press the MENU button again.
5.2 Easy Controller
The easy remote control is used only in master/slave mode. By
Reset
connecting to the 1/4” microphone jack of the first unit, you will find
Press the MENU button up to when the
that the remote control on the first unit will control all the other units
button and all channels of the unit will return to their standard position. To go back to the
for Stand by, Strobe/Next and Fast/Slow function.
functions press the MENU button again.
is blinking on the display. Pressing ENTER
4.2 Main Function
Show Mode
To select any of the given functions, press the MENU button up to when the required
one is showing on the display. Select the function by ENTER button and the display will blink.
Press the MENU button up to when the
Use DOWN and UP button to change the mode. Once the required mode has been selected,
button and the display will blink. Use DOWN and UP button to select the
press the ENTER button to setup or it will automatically return to the main functions without
any change after idling 8 seconds. To go back to the functions without any change press the
(show 2) or
(show 3) or
(show 4) mode. Once the mode has
or
been selected, press the ENTER button to setup or automatically return to the main
MENU button. The main functions are showing below:
functions without any change after 8 seconds. To go back to the functions without any
is showing on the display. Pressing ENTER
(show 1)
change press the MENU button again.
Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210°.
Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90°.
Show 3 mode - Fixture is placed on the speaker, The spot is always projecting
to the audience’s direction; i.e in front of the stage. Pan movement angel ( left to
right to left ): 160°. Tilt movement angel: 90° ( 60° above horizon; 30° below
horizon.)
Show 4 mode - Fixture is fixed under ceiling. The spot is mainly projecting in
front of the stage. Pan movement angel ( left to right to left ) :160°. Tilt
movement angel: 90° ( vertically, front 75°; back 15° )
10A
Slave Mode
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(2 light show) mode. Once the mode has been selected, press the
(normal) or
ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
again.
Blackout Mode
DMX512 Address Setting
Press the MENU button up to when the
Press the MENU button up to when the
is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
Once the address has been selected, press the ENTER button to setup or automatically
(yes blackout) or
(no blackout) mode. Once the mode has been selected, press the
ENTER button to setup or automatically return to the main functions without any change
return to the main functions without any change after 8 seconds. To go back to the functions
after 8 seconds. To go back to the functions without any change press the MENU button
without any change press the MENU button again.
again.
Color Mode
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(split color) mode. Once the mode has been selected, press the
(normal) or
ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
again.
Pan Inversion
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(pan inversion) mode. Once the mode has been selected, press the
(normal) or
ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
again.
11A
Tilt Inversion
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(tilt inversion) mode. Once the mode has been selected, press the
(normal) or
ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
again.
Led Display
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(Led off) mode. Once the mode has been selected, press the ENTER
(Led on) or
button to setup or automatically return to the main functions without any change after 8
seconds. To go back to the functions without any change press the MENU button again.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement