5.3 playing a scene with the speed slider

5.3 playing a scene with the speed slider
DMX 512 CONTROLLER SERIES
TABLE OF CONTENTS
1. Safety Instructions……………………………………………………… …… 2
Before You Begin ……………………………………………………………... 2
What is included………………………………………………………………… 2
Unpacking Instructions…………………………………........................................ 2
2. Features………………………………………………………………………… 3
Introduction……………………………………………………………………… 3
Product overview (front)……………………………………………………… 4-5
Product 0verview (rear panel)……………………………………………………. 6
3. Operating Instructions………………………………………………………… 6
Initial Setup……………………………………………………………………… 6
Physical fader Assignment (optional setup)……………………………………… 7
4. Programming…………………………………………………………………
7
Entering program mode (record enable)…………………………………………… 7
Create a scene……………………………………………………………………… 8
Edit Enable ………………………………………………………………………… 8
Delete a Program Action…………….………………………………………………8
Delete All Scenes Action……………………………………………………………9
Record Clear Action……………………………………………………………… 9
Delete a step or steps……………………………………………………………….. 9
Insert a step or steps……………………………………………………………… 9
Modify a step or step………………………………………………………….
10
5. Playback…………………………………………………………………………. 10
Playing a Scene……………………………………………………………….….. 10
Playing a Scene to music………………………………………………………….. 10
Playing a Scene with the Speed slider………………………………… ………... 11
Plating a Scene with the Standard beat…………………………………………….. 11
Change the Speed mode between 5 & 10 minutes……………………………… 11
Auxiliary controls…………………………………………………………………...11
Setting MIDI IN……………………………………………………………... 12-13
Setting MIDI OUT………………………………………………………………… 13
Receiving MIDI File Dump…………………………………………………… …. 13
Sending MIDI File Dump……………………………………………………… ….14
6.Appendix……………………………………………………………………… … 14
DMX Primer……………………………………………………………………… 14
Fixture Linking…………………………………………………………………… 15
General Troubleshooting ……………………………………………………… 15-16
DMX Dip switch Quick Reference Chart…………………………………………..17
Technical Specifications…………………………………………………… …
18
Quick operation…………………………………………………………………… 19
USER MANUAL 1/19
DMX 512 CONTROLLER SERIES
1.1 Safety Instructions
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance of your fixture.
„
„
„
„
„
„
„
„
.
Please keep this User Guide for future consultation. If you sell the unit to another
user, be sure that they also receive this instruction booklet.
Always make sure that you are connecting to the proper voltage and that the line
voltage you are connecting to is not higher than that stated on decal or rear panel
of the fixture.
This product is intended for indoor use only! To prevent risk of fire or shock, do not
expose fixture to rain or moisture. Make sure there are no flammable materials close to
the unit while operating
In the event of serious operating problem, stop using the unit immediately. Never try
to repair the unit by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center. Always use the same type spare parts.
Don’t connect the device to a dimmer pack.
Make sure power cord is never crimped or damaged.
Never disconnect power cord by pulling on the cord.
Do not operate this device in more than 104F(40°C) ambient temperature conditions.
Caution! There are no user serviceable parts inside the unit. Do not open the housing
or attempt any repairs yourself. In the unlikely event your unit may require
service. Please contact us.
1.2 BERORE YOU BEGIN
What is include
1) DMX-512 dimming console
2) DC 9~12V 1000mA output
3) Manual
4) LED gooseneck lamp
1.3 Unpacking Instructions
Immediately upon receiving the fixture, carefully unpack the carton, check the contents
to ensure that all parts are present, and have been received in good condition. Notify the
shipper immediately and retain packing material for inspection if and parts appear damaged
from shipping or the carton itself shows signs of mishandling. Save the carton and all
packing materials. In the event that a fixture must be returned to the factory, it is important
that the fixture be returned in the original factory carton and packing.
USER MANUAL 2/19
DMX 512 CONTROLLER SERIES
2.1 Features
* 24-channel DMX-512 dimming console
* 4 pages with 12 scenes with total 48 playback faders (simultaneous playback)
* 4800 programmable steps
* 2 programmable AUX buttons
* Adjustable chase and fade time
* Re-assignable channels
* 3-pin and 5-pin DMX outputs
* Built-in cross fader, dark and kill buttons
* Direct audio input
* Sequential linking or simultaneous playback of chases
* Override chases on the fly
* Beat-active mode, tap sync mode and auto run
* 7U Rack mountable
2.2 INTRODUCTION
2.3
This dimmer console is a universal intelligent lighting controller. It allows the
control of 24 channels with 48 scene/chase playback faders. Each scene/chase can contain
up to 1000 individual steps, or looks. On the surface, when in the CHASE SCENE mode,
there are 12 physical faders for the playback of the saved programs. There are 4 pages of
scenes playback on page A. programs can be triggered by music, automatically or
manually. Channel assignments can be reprogrammed for ease of controlling different
fixtures. On the surface you will find various programming tools such as 24channel
faders. A/B master faders for cross mixing and Fade and Speed time faders for on the fly
adjustments. It also has an LCD display for easy navigation of controls and menu
functions.
USER MANUAL 3/19
DMX 512 CONTROLLER SERIES
22..44 Product Overview (front)
ITEM
Button or Fader
1
Channel Faders
Function
Channel faders 1-24
2
Flash button
0-100%dimming or DMX value of 255 for channels 1-12
3
4
Faders LEDs
Scene LEDs
Indicates selected channel 1-24
Indicates which scene is being playing back
5
Channel Flash buttons
0-100%dimming or DMX value of 255 for channels 13-24
6
Down/Beat Rev
7
Up/Chase Reverse
8
LCD display
9
Delete/Rev One
10
Aux 1
11
Insert % or 25
Down functions to modify a scene in edit mode, Beat Rev
is used to reverse the chasing of a program with regular
beat
Up function is to modify a scene in edit mode, chase
reverse is used to reverse the chasing direction of a
program under speed slider control.
Shows the current programming
Delete a step in a scene or reverse the chasing direction of
any program
Control a channel in 1 of 2 modes of Operation
Insert is to add 1 steps into a scene; %or255 is used to
change the display value cycle between % and 0-255
USER MANUAL 4/19
DMX 512 CONTROLLER SERIE
12
Aux 2
13
Edit/All Rev
14
Record/Shift
15
Audio
16
Blind
17
Dark
Used to temporarily blackout overall output
18
Home
Used to deactivate the Blind on a given channel
Used to select Single/Mix Chase, bring Channel
13-24 to full of current setting, or momentarily
program a scene into Master B slider depending
on the current mode
Used to activate the operating mode; Rec Speed
sets the speed of any programs chasing in Mix
mode
Repeatedly tapping this button will establish the
chase speed
Used the momentarily maintain current scene
Tap to select pages of scenes from 1-4(Page A)
Bring all channels (1-24) to full intensity
Used to go to the next step when the Speed slider
is 25 set in Show Mode or in Edit mode
In Add mode, multiple scenes or Flash buttons
will be on at the same time; In kill mode,
pressing any Flash button will kill any other
scenes or programs; Rec Exit is used to exit from
Program or Edit mode
Used to kill all output, with exception of Full On
19
Park
Control a channel in 1 of 2 modes of operation
Edit is used to activate Edit mode; All Rev is to
reverse the chasing direction of all programs
Record is used to activate Record mode or
program a step; Shift functions the alternate
function of other buttons only
Audio activate audio sync of a program
Take the channel out of a program temporarily in
Chase Scene mode
20
Mode Select/Rec Speed
21
Tap Sync
22
23
24
Hold
Page
Full On
25
Step
26
Add Kill/Rec exit
27
Blackout
28
Audio Level Fader
Adjusts the audio sensitivity when in Audio
trigger mode of scenes
29
Speed Fader
Adjust the speed of scenes/chases running 29
30
Fade Fader
Adjusts the fade-in, fade-out, and cross-fade
times
31
Master A-B
Adjusts overall output
USER MANUAL 5/19
DMX 512 CONTROLLER SERIES
2.5 Product Overview (rear panel)
ITEM
Button or Fader
Function
1
3 spin DMX Sockets
DMX output Sockets
2
USB Lamp Socket
For USB Lamp
3
Power ON/OFF switch
To turn the console on or off
4
Audio Input
This jack accepts a line level audio input
signal ranging from 100 mv to 1Vpp
5
Remote Input
Blackout and Full On may be controlled by a
remote control using a standard 1/4 jack
6
DC Input
DC 9v 1000ma
3. OPERATING INSTRUCTIONS
3.1 Initial setup
(1) Plug the AC to DC power supply into the system back panel and into the mains
outlet.
(2) Plug in your DMX cable(s)to your intelligent lighting as described in the respective
fixtures manual. For a quick overview of DMX see the DMX Primer on page 11
(3) Place the 24 CH dimmer console on a level surface Note! The console can also be
rack mounted, occupying six rack spaces (7u).
(4) Reset the system using the instructions on page 9 under ERASE ALL SCENES.
USE RMANUAL
6/19
DMX 512 CONTROLLER SERIES
3.2 PHYSICAL FADER ASSIGNMENT (Optional Setup )
Use this feature to combine or unify fixture control attributes for different fixtures.
For example: if you were controlling 4 moving mirrors and 4 moving yokes, the color,
gobo and dimmer channels may not line up ideally on the physical faders. Use this function
to re-assign the dimmer, color and gobo channels 1,2 and 3. From now on you will be able
to control the same attributes on all fixtures using the same fader location.
1. Press and hold RECORD button.
2.While holding the Record button. Press the Flash button 6,3 time.
3.Now press the Flash button that you wish to assign the DMX channel output to.
4.White holding Record button, press the Flash button corresponding to the DMX
output that you wish to assign the Fader to.
5.Repeat steps 2-3 as often as necessary
6.Press and hold Record & Rec Exit to exit the mod
For example: If you wish to assign Fader 1 to output to DMX channel 5
1. Hold the Record button & press Fader 6, 3 times
2. Press the Flash button 1.
3. While holding the Record button, press the Flash button 5.
NOTES:
Al physical faders can be re-assigned to output on a different DMX channel, Faders
are given a channel number and are printed on the surface of the controller as such.
You can check to see what the assignment is by pressing the Fader button of the
corresponding channel while in this mode.
Here is no limit to the amount of channels that can be assigned to a single fader. One
can assign up to all 24 channel while in this mode.
CHNO corresponds to the Physical Fader, while SLDNO corresponds to the DMX
output channel.
4. PROGRAMMING
4.1 ENTERING PROGRAM mode (RECORD ENABLE)
1. While holding the RECORD button, tap the FLASH buttons 1-5-6-8 in sequence.
2. Release the RECORD button. The Record LED will light up now
USE RMANUAL
7/19
DMX 512 CONTROLLER SERIES
4.2 CREATE A Scene.
A scene is a static lighting state. Scenes are stored in the temporary memory, until they
are transferred to one of the playback faders. You may create a single scene or a
succession of up to 999 steps per Scene.
1) Record enable.
2) Select the 1-24 Single mode by tapping the Mode Select button. This will give you
control of all 24 channels of the first page.
3) Compose a look by moving the FADERS. (Changes in fixture attribute such as
colors and gobos, or simply dimmer values).
4) Press Record to save the look into the temporary memory.
5) Repeat steps 2 ~ 4 until you have your desired scene.
6) Adjust the Speed and Fade sliders to achieve the desired amount of time a scene
will be held in a chase (speed) and the amount of time allowed for the fixtures to
move from one scene to the next (fade).
7) Select a Scene master to store your scene. Tap the Page button to select a page (1-4).
8) Press and hold the RECORD button & tap the Flash button for the scene that you
wish to store it to. All LEDs will flash indicating the scene has been programmed
into memory.
9) You can continue programming or exit. To exit program mode, press and hold the
RECORD button & tap the REC EXIT button.
4.3 EDIT ENABLE
1) Record enable.
2) Use the Page button to select the page the program you wish to edit is on.
3) Tap the Mode Select button to select Chase Scenes.
4) Press and hold the Edit button & tap the Flash button (13-24) of the Scene you
wish to edit.
5) Release the Edit button. The relevant Scene Led should light, indicating you are in
edit mode.
Notes
z When the EDIT mode is entered properly, the display will read EDITING.
z This mode is displayed here for only the initiation of EDIT mode. Please see the
following sections on the uses of this mode in detail
4.4 Delete a Program Action
1) Record enable.
2) Use the Page button to select the page the Scene you wish to delete.
3) Press and hold Record button & tap the Flash button (13-24) twice of Scene you
wish to delete
4) Release RECORD button and all LEDs should be lit to indicate the program is
delete.
USE RMANUAL
8/19
DMX 512 CONTROLLER SERIES
4.5 Delete All Scenes Action
1) Record enable
2) Press and hold RECORD button
3) While holding the record button tap the flash button in the following sequence: 1-3-23.Relese the RECORD button.
4) All LEDS should light indicating all program have been erases.
5) Press and hold RECORD & REX EXIT to exit the mode.
Warning: This will reset the controller to its factory setting
NOTES:
z You must be in record mode to reset the console.
z The LED over the record button will light up, indicating the Record mode
operation.
4.6 RECORD CLEAR ACTION
1) Record enable.
2) Record a scene with 1 or more steps.
3) If you are not satisfied with the scene, you may press and hold the Record button &
tap the Page/REC CLR button. All LEDs will flash, indicating the scenes have been cleared.
Notes
z All scenes be stored in the temporary memory of the controller will be erased by this
process.
z This process will not affect the scenes already programmed into a Scene fader.
4.7 DELETE A STEP OR STEPS
1) Enter the EDIT mode.
2) Tap the Step button to scroll to the step you wish to delete
3) Tap the Delete button when you reach the step. You wish to delete.
4) Repeat step 2 and 3 all of the unwanted steps have been deleted.
5) Press and hold the Record REC Exit button. The SCENE BUTTON LED will turn
off, indicating that the Edit mode has been exited.
4.8 INSERT STEP OR STEPS
1) Record a scene or scenes you wish to insert.
2) Be sure you are in Chase Scene and enter the EDIT mode.
3) Tap the Step button to scroll to the step you wish to insert the step before. You may
read the step from display.
4) Tap the INSERT button to insert the step you have created before.
5) Exit Edit mode.
NOTES:
„ Part of entering the Edit mode is selecting scene you wish to edit. See section on
Edit enable for further instruction.
„ AII LEDS will flash to indicating a successfully Insert of the step.
USER MANUAL
9/19
DMX 512 CONTROLLER SERIES
4.9 MODIFY A STEP OR STEPS
1) Enter EDIT mode.
2) Tap the STEP button to scroll to the step you wish to insert the step before. You may
read the step from display.
3) While holding the UP or DOWN button, tap the Flash button corresponding to the
DMX channel of the Scene you wish to modify until you reach the desire intensity
value read from the display. Then, you may tap the Flash buttons until you are
satisfied with the new Scene.
4) Repeat step2, 3 and 4 until all the steps have been modified.
5) Exit EDIT mode.
NOTES:
z Part of entering the Edit mode is selecting which scene you wish to edit. See section
on enable for further instructions.
z ALL LEDS will flash to indicate a successful insert of the step.
5. Playback
This controller uses the Channel Faders and Channel Flash buttons for multiple uses. In
this occurrence, Channel faders 13-24 are used playing back of scenes already recorded.
This is only when the controller is the Chase
scene mode. In this instance, Master
Fader A will control manual fader controls, whish Master Fader B will control the
Scenes being played back.
5.1 PLAYING A SCENE
1) Tap the MOPE SELECT button to select Chase SCENE mode indicated by the
red LED.
2) Tap the page to select the correct page the program you wish to run is located.
3) Push master Slider B to its maximum position (fully down)
4) Move the desired Channel slider (13-24) to its maximum position to trigger the
program, and the program will fade in depending upon current fade time. You may
press and hold down the relevant FLASH button (13-24) to trigger the program.
5) Move the channel Slider to adjust the output of the current program.
5.2 PLAYING A SCENE TO MUSIC
1) Use built-in microphone or plug the audio source into the RCA Audio jack
2) Select your program as described active.
3) Tap the Audio button until LED light, indicating AUDIO mode is active.
4) Tap the Audio Level slider to adjust the music sensitivity.
5) To return to normal mode, tap the Audio button a second time, causing its LED go
out. Audio mode is now disengaged.
USE RMANUAL 10/19
DMX 512 CONTROLLER SERIES
5.3 PLAYING A SCENE WITH THE SPEED SLIDER
1) Be sure the Audio mode is disengaged.
2) Select your program as described above.
3) Move the Speed slider to SHOW MODE position then tap the Flash button (13-24)
while pressing and holding down the REC SPEED button, the correspond ding
standard beat any longer.
4) Now, you may move the Speed slider to select your desired speed.
NOTES:
z The steep 3 is not necessary if the selected program is not recorded with the standard
Beat.
5.4 PLAYING A SCENE WITH THE STANDARD BEAT
1) Be sure the Audio is disengaged, the Mode select button to select Chase Scene
mode.
2) Tap the Park button to select Mix Chase mode. The LED lights at upper indicating the
selection.
3) Select your program as described above. You may tap the Tap sync button twice to
define your beat time.
4) Move the Speed slider until the segment display reads your desired value.
5) While pressing and holding down the Rec Speed button, tap the Flash button (13-24)
that stores the program. The Scene will now run with the set time or beat when
engaged.
6) Repeat steps 4 & 5 to set a new beat time
NOTES:
z Be sure AUDIO mode is disengaged. As an alternative to using the Speed slider to input
the speed, you may use the Tap sync button (2) times to define your beat
5.5 CHANGE THE SPEED MODE BETWEEN 5 & 10 MINUTES
1) Press and hold the Record button.
2) Tap the Flash button 5 or 10 three times while holding down the RECORD button.
3) The 5min or 10min LED should light up indicating the Speed slider is set to run in the
5 or 10 minute mode.
5.6 AUXILIARY CONTROLS
This is the process of assigning the Auxiliary controls. These will act as shortcuts and are
most commonly used for DMX strobe lights or DMX fog machines. However, they are not
limited to these functions and may be used for other uses such as pan/tilt
1) Press & hold RECORD & tap the Flash button 7 or 8 (3) times. The display should
indicate activation of the mode.
USE RMANUAL 11/19
DMX 512 CONTROLLER SERIES
2) There are 3 functions:
z FUNC1 states that the Auxiliary control is not assigned to any channel.
z FUNC2 refers o the auxiliary controls working much like the channel fader along
with the flash buttons.
z FUNC3 is somewhat different. The rotary knob acts to set the total output of the
flash button below it. (i.e. rotary control 0-8,flash button also 0-8)
3) While holding down the RECORD button, select the function you wish for the
auxiliary control by pressing the Flash button 1, 2, or 3 this Release the buttons.
4) To assign the auxiliary to a channel, press the Flash button for the channel you wish to
assign the auxiliary control to. This sets channel assignment. The corresponding Led
above the channel will light, indicating that the channel has ben assigned.
5) Record exit.
Notes
z
z
z
You may refer to the display for the functions being edited.
Press 7 three times for AUX 1 patching, and 8 three times for AUX 2 patching.
While assigning an auxiliary to mode 2, the Fader for that channel will not function.
It will act as moving the channel.
z While assigning an auxiliary to mode 3, the channel fader and the auxiliary controls
will both work for that channel on an HTP operating principle (highest takes
precedent).
Setting MIDI IN
Action
1) While holding down the RECORD button, simultaneously tap to Flash button #1 three
times. The display reads MIDI CHANNEL IN to indicate channel setup is available.
2) Select the MIDI control channel (1-16) by tapping Flash button 1-16.The relevant
channel LED lights indicating MIDI IN channel is est.
3) While holding down RECORD, tap the REC EXIT button to exit MIDI setting.
USE RMANUAL 12/19
DMX 512 CONTROLLER SERIES
MIDI NOTE
FUNCTION(TURN ON/OFF)
27-69
70-93
94
95
Tum on or off program 1-48
Activate Channel 1-24
FULL-ON
DARK(momentary blackout)
96
97
98
99
100
101
102
HOLD
Tum on or off AUDIO
Chase SCENE
MODE: 1-12A-1-12B
MODE: 1-24A
Step
BACKOUT
Notes: This is the Channel that the controller will receive MIDI note commands
Notes: When working with MIDI notes 22-93,you may simulate a fader increase and
decrease by adjusting the velocity of the note.
Setting MIDI OUT
Action
4) While holding down the RECORD button, simultaneously tap Flash button #2 three
times. The display reads MIDI CHANNEL OUT to indicate channel setup is
available.
5) Select the MIDI control channel (1-16) by tapping Flash button 1-16.The relevant
lights indicating MIDI OUT channel is set.
6) While holding down RECORD, tap the REC EXIT Button to exit MIDI setting.
Notes: This is the channel that the controller will transmit MIDI note commands.
Receiving MIDI File Dump
Action
7) While holding down the RECORD button, simultaneously Flash button #3 three times.
The display reads MIDI FILEDUMP RECVING 000%wen the device is in the
correct mode.
8) While holding down RECORD, tap the REC EXIT button to exit MIDI setting.
Notes: This is process of copying show to another same 48 CH dimmer console.
This will not work with any other device
This process can take several minutes to complete.
The console automatically being the FILE DUMP once the mode has been selected.
USE RMANUAL 13/19
DMX 512 CONTROLLER SERIES
Therefore, be sure that the other deceive has preciously been setup to receive the transfer.
During FILE DUMP, all other operation will cease to function.
If errors or power failure occurs, FILE DUMP will be interrupted and stop
Sending MIDI File Dump
Action
9) While holding down the RECORD button, simultaneously tap Flash #4 three times,
the display reads MIDI FILE DUMP SENDING 000%when the device is in correct
mode.
10) While holding down RECORD, tap the REC EXIT button exit MIDI setting.
Notes: This is the process of copying your entire show to another same
24CH dimmer console.
This will not work with any other device.
This process can take several minutes to complete.
The control will automatically being the FILE DUMP once the
mode has been selected.
Therefore, be sure that the other device has previously been setup
to receive the transfer.
During FILE DUMP, all other operations will cease to function.
If errors or power failure occurs, FILE DUMP will be interrupted and stop
6.APPEMDIX
DMX Primer
There are 512 channels in a DMX 512 connection. Channel may be assigned in any
manner. A fixture capable of receiving DMX 512 will require one or a number of
sequential channels. The user must assign beginning address on the fixture that
indicates the first channel reserved in the controller. There are many different types of
DMX controllable fixture and they all may vary in the total number of channels
required, Choosing a start address should be planned in advance, Channels should never
overlap. If they do, this will result in erratic operation of the fixture s whose starting
address is set incorrectly. You can however, control multiple fixture of the same type
using the same starting address as long as the intended result is that of unison
movement or operation, In other words, the fixture will be slaved together and all
respond exactly the same. DMX fixtures are designed to receive data though a serial
Daisy Chain. A Daisy Chain connection is where the DATA OUT of one fixture
connects to the DATA IN of the next fixture. The order in which the fixtures are
connected is not important and has no effect on how a controller communicates to each
fixture. Use an order that provides for the easiest and most direct cabling. Connect
fixtures using shielded two conductor twisted pair cable with three pin XLR male to
female connectors, The shield connection is pin 1, while pin 2 is Data Negative (S-) and
pin 3 is Data positive (S+)
USE RMANUAL 14/19
DMX 512 CONTROLLER SERIES
FIXTURE LINKING
Occupation of the XLR-connection:
120 ohm
PIN2
PIN3
Caution: At the last fixture, the DMX-cable has to be terminated with a
terminator. Solder a 120Ω resistor between Signal (-) and Signal (+) into a 3-pin
XLR-plug and plug it in the DMX-output of the last fixture.
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected
with a DMX terminator. This prevents electrical noise from disturbing and corrupting the DMX
control signals. The DMX terminator is simply an XLR connector with a 120W (ohm) resistor
connected across pins 2 and 3, which is then plugged into the output socket on the last projector
in the chain. The connections are illustrated below
If you wish to connect DMX-controllers with other XLR-outputs, you need to use adaptercable. The transform of the controller line of 3 pins and 5 pins (plug and socket)
Genera l Troubleshooting
Symptom
Auto shut off
Beam is very
dim Or nor
bright
Breaker/Fuse
Keeps blowing
Chase is too
slow
Solution(s)
Applies to
Lights
Check fan thermal
switch reset
Check optical system
or lamp Check
220V/110V switch for
proper setting
Check total load on
device
√
Check users manual
for speed adjustment
√
Fogs
& Snow
Consoles
Dimmers&
Chaser
√
√
√
√
USE RMANUAL 15/19
DMX 512 CONTROLLER SERIES
Check for power on main
Check device’s fuse.
(Internal and/or external)
Check DMX Dip switch
setting for Correct
Fixture is not
addressing. Check DMX
responding
cables Check polarity
Switch settings
Make sure you have the
audio mode on the
Fixture is on but correct
console.
If provide via ¼
There is no
jack,
make
a live
movement to the audio signalsure
exist.
audio
Adjust sound sensitivity
knob.
Possible bad lamp or
Lamp cuts off
fixture is Overheating.
Lamp may be lamp end of
Sporadically
its life.
Some discharge lamps
require a cooling off
Light will not
period before the
Come on after
electronics in the fixture
can kick. Start it again,
Power failure
wait 5 to 10 minutes
Before powering up.
Use only DMX cables
Install terminator.
Loss of signal
Note: Keep DMX cables
be separated from power
cable or black lights.
Check 200V/11V switch
Moves slow
for proper Setting.
Re-install bulb, may have
No flash
shifted in Shipping,
readjust
Bounce mirror motor may
No light output
have Shifted during
shipping
Check slip ring & brushes
No light output
For contact Install bulb
Call service technician
Check reset switch
Relay will not
work
Check cable connections
Remote does not Make sure connection is
work
firmly connected to device
All lighting fixtures
featuring Standalone
function do not require
Stand alone mode additional settings, simply
power the fixture and it
will automatically enter
into this mode
Device has no
Power
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
USE RMANUAL16/19
DMX 512 CONTROLLER SERIES
6.5 DMX Dipswitch Quick Reference Chart
Dip Switch Position
DMX DIP SWITCH SET
0=OFF
1=ON X=OFF
or ON
#1 #2 #3 #4 #5
0 0 0 0 0
1 0 0 0 0
0 1 0 0 0
1 1 0 0 0
0 0 1 0 0
1 0 1 0 0
0 1 1 0 0
1 1 1 0 0
0 0 0 1 0
1 0 0 1 0
0 1 0 1 0
1 1 0 1 0
0 0 1 1 0
1 0 1 1 0
0 1 1 1 0
1 1 1 1 0
0 0 0 0 1
1 0 0 0 1
0 1 0 0 1
1 1 0 0 1
0 0 1 0 1
1 0 1 0 1
0 1 1 0 1
1 1 1 0 1
0 0 0 1 1
1 0 0 1 1
0 1 0 1 1
1 1 0 1 1
0 0 1 1 1
1 0 1 1 1
0 1 1 1 1
1 1 1 1 1
#9
#8
#7
#6
Dip Switch Position
0
0
0
0
0
0
0
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
0
0
1
0
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
0
0
1
1
0
1
0
0
0
1
0
1
96 128 160
97 129 161
98 130 162
99 131 163
100 132 164
101 133 165
102 134 166
103 135 167
104 136 168
105 137 169
106 138 170
107 139 171
108 140 172
109 141 173
110 142 174
11 14 175
11 14 176
11 14 177
11 14 178
11 14 179
11 14 180
11 14 181
11 15 182
11 15 183
12 15 184
12 15 185
12 15 186
12 15 187
12 15 188
12 15 189
12 15 190
12 15 191
0
1
1
0
0
1
1
1
192 224
193 225
194 226
195 227
196 228
197 229
198 230
199 231
200 232
201 233
202 234
203 235
204 236
205 237
206 238
207 239
208 240
209 241
210 242
211 243
212 244
213 245
214 246
215 247
216 248
217 249
218 250
219 251
220 252
221 253
222 254
223 255
1
0
0
0
1
0
0
1
256 288
257 289
258 290
259 291
260 292
261 293
262 294
263 295
264 296
265 297
266 298
267 299
268 300
269 301
270 302
271 303
272 304
273 305
274 306
275 307
276 308
277 309
278 310
279 311
280 312
281 313
282 314
283 315
284 316
285 317
286 318
287 319
1
0
1
0
1
0
1
1
1
1
0
0
1
1
0
1
1
1
1
0
1
1
1
1
320 352 384 416 448 480
321 353 385 417 449 481
322 354 386 418 450 482
323 355 387 419 451 483
324 356 388 420 452 484
325 357 389 421 453 485
326 358 390 422 454 486
327 359 391 423 455 487
328 360 392 424 456 488
329 361 393 425 457 489
330 362 394 426 458 490
331 363 395 427 459 491
332 364 396 428 460 492
333 365 397 429 461 493
334 366 398 430 462 494
335 367 399 431 463 495
336 368 400 432 464 496
337 369 401 433 465 497
338 370 402 434 466 498
339 371 403 435 467 499
340 372 404 436 468 500
341 373 405 437 469 501
342 374 406 438 470 502
343 375 407 439 471 503
344 376 408 440 472 504
345 377 409 441 473 505
346 378 410 442 474 506
347 379 411 443 475 507
348 380 412 444 476 508
349 381 413 445 477 509
350 382 414 446 478 510
351 383 415 447 479 511
DMX Address
USER MANUAL 17/1 9
DMX 512 CONTROLLER SERIES
Technical Specifications
WEIGHT & DIMENSIONS
Length…………………………………………………………………. (485 mm)
Width…………………………………………………………………….(290 mm)
Height…………………………………………………………………….(98mm)
Weight ……………………………………………………………………… (5kg)
POWER
Operating……………………… ………DC 9V 1000ma 100-240v auto switching
Adapter……………………………………………………………... . 2-pinEdison
THERMAL
Maximum ambient temperature …………………………………….104°F (40°)
CONTROL &PROGRAMMING
3-pin DMX:
Data output……………………………… ………Locking 3-pin XLR female socket
Data pin configuration……………………..………...Pin 1 shield, pin 2 ㈠,pin 3(+)
Protocols……………………………………………………...... DMX-512 USITT
USER MANUAL 18/19
DMX 512 CONTROLLER SERIES
Appendix: Quick operation
Manual operation
1) Connect to power, Press BLACK OUT and yellow LED light OFF
2) Move sliders of MASTER A and FADE to top.
3) Use MODE SELECT to select 1-24 SINGLE mode
4) Move sliders to change DMX value to control lighting fixture
Program
1, Connect to power, Press BLACK OUT and yellow LED light OFF
2, Move slider of MASTER A channel and FADE channel to the top.
3, Use MODE SELECT to select 1-24 SINGLE mode
3.1 - Edit Scene
3.1.1: Keep pressing RECORD and press FLASH button 1-5-6-8 to enter
PROGRAM stat us. RECORD LED ON.
3.1.2: Move sliders of channels to get suitable effect
3.1.3: Press RECORD to save current effect (all LED lamps of slider area will
flash one time). LCD display bottom line show [STEP NO 001]
3.1.4: Repeat step 3.1.2 & 3.1.3 to program scene you need.
3.2 - Save scene to program slider:
3.2.1: Press PAGE to select program page -- total 1-4 pages, 12 program sliders
each page)
3.2.2: Keep pressing RECORD and correspond FLASH button of 13-24 sliders (all
LED lamps of slider area will flash one time). Then current scene will be saved to
selected program slider.
3.2.3: Repeat steps 3.1.2, 3.1.3, 3.1.4, 3.2.1, 3.2.2 to edit and save other program
sliders.
Run program
1, Press MODE SELECT button to get CHHASE
SCENES and select running
mode
2, Press PAGE button to select running program page.
3, Move sliders of correspondent running program channel (13-24) to top and it°
Os yellow LED lamp ON
4, Move SPEED slider to set program FADE IN time.
5, Press PARK B to select SINGLE CHASE (- Recycle mode and red LED lamp ON)
or MIX CHASE (- run all selected program at same time and yellow LED lamp light up)
USER MANUAL 19/19
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement