Federal Communications Commission Statement(Class A)

Federal Communications Commission Statement(Class A)
ENGLISH
F e d e r a l C o m m u n i c a t i o n s C o m m i s s i o n S t a t e m e n t ( C l a s s A)
NOTE- This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by tuning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
ƒ Reorient or relocate the receiving antenna.
ƒ Increase the separation between the equipment and receiver.
ƒ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
ƒ Consult the dealer or an experienced radio/television technician for help.
Class A ITE:
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B ITE limits.
Such equipment should not be restricted in its sale but the following warning shall be included in the
instructions for use:
Warning - This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.
CE Class A (EMC)
This product is herewith confirmed to comply with the requirements set out in the Council
Directives on the Approximation of the laws of the Member States relating to Electromagnetic
Compatibility Directive 2004/108/EEC.
Warning - This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures to correct this interference.
D I S C L AI M E R
No warranty or representation, either expressed or implied, is made with respect to the contents of this
documentation, its quality, performance, merchantability, or fitness for a particular purpose. Information
presented in this documentation has been carefully checked for reliability; however, no responsibility is
assumed for inaccuracies. The information contained in this documentation is subject to change without
notice.
In no event will AVer be liable for direct, indirect, special, incidental, or consequential damages arising out of
the use or inability to use this product or documentation, even if advised of the possibility of such damages.
T R AD E M AR K S
AVerVision is registered trademarks of AVer Information Inc. IBM PC is a registered trademark of
International Business Machines Corporation. Macintosh is a registered trademark of Apple Computer, Inc.
Microsoft is a registered trademark and Windows is a trademark of Microsoft Corporation. All other products
or corporate names mentioned in this documentation are for identification and explanation purposes only,
and may be trademarks or registered trademarks of their respective owners.
COPYRIGHT
© 2011 by AVer Information Inc. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language in any form by any means without the written permission of AVer Information Inc.
ENGLISH
THE MARK OF CROSSED-OUT WHEELED BIN INDICATES THAT THIS PRODUCT
MUST NOT BE DISPOSED OF WITH YOUR OTHER HOUSEHOLD WASTE.
INSTEAD, YOU NEED TO DISPOSE OF THE WASTE EQUIPMENT BY HANDING IT
OVER TO A DESIGNATED COLLECTION POINT FOR THE RECYCLING OF WASTE
ELECTRICAL AND ELECTRONIC EQUIPMENT. FOR MORE INFORMATION ABOUT
WHERE TO DROP OFF YOUR WASTE EQUIPMENT FOR RECYCLING, PLEASE
CONTACT YOUR HOUSEHOLD WASTE DISPOSAL SERVICE OR THE SHOP
WHERE YOU PURCHASED THE PRODUCT.
Remote Control B a t t e r y S a f e t y I n f o r m a t i o n
-
Store batteries in any cool & dry place.
Do not dispose used batteries in domestic waste. Dispose batteries at special collection points
or return to stores if applies.
Remove the batteries if they are not in use for long period of time. Battery leakage and
corrosion can damage the remote control, dispose batteries safely.
Do not mix and use old and new batteries.
Do not mix and use different types of batteries: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
Do not dispose batteries in a fire.
Do not attempt to short circuit the battery terminals.
ENGLISH
Table of Contents
Package Contents ........................................................................... 1 Optional Accessories ..................................................................... 1 Get Familiar with the AVerVision F30 ............................................ 2 Right Panel ............................................................................................. 2 Rear Panel ............................................................................................. 3 Left Panel ............................................................................................... 3 Control Panel.......................................................................................... 4 Remote Control ...................................................................................... 6 Making the Connections ................................................................ 9 Set the TV-RGB Switch Setting .............................................................. 9 Connect to a Monitor or LCD/DLP Projector......................................... 10 Connect to a TV ................................................................................... 10 Connecting the Power ........................................................................... 11 Connect to a Computer ......................................................................... 11 Connect to a Computer via USB .......................................................... 12 Connect an External Microphone ......................................................... 12 Connect an Amplified Speaker ............................................................. 13 Connect to a Microscope ...................................................................... 13 Setting Up AVerVision F30 ........................................................... 14 Storing and Handling ............................................................................ 14 Shooting Area ....................................................................................... 15 Overhead Light ..................................................................................... 16 Infrared Sensor..................................................................................... 16 Anti-glare Sheet.................................................................................... 16 External Memory Storage ..................................................................... 17 d ........................................................................... 17 Insert an SD Car
Card
Insert a USB Flash Driv
e ................................................................ 17 Drive
OSD MENU ..................................................................................... 18 Navigate the Menu and Submenu ........................................................ 19 Image ................................................................................................... 19 Brightness ....................................................................................... 19 Contrast .......................................................................................... 19 Mode ............................................................................................... 20 Effect............................................................................................... 20 Mirror .............................................................................................. 20 Advanced ........................................................................................ 20 Auto Image ..................................................................................... 21 Exposure ........................................................................................ 21 White Balance................................................................................. 21 Focus .............................................................................................. 21 Presentation ......................................................................................... 22 Spotlight .......................................................................................... 22 Visor................................................................................................ 22 ENGLISH
PIP .................................................................................................. 23 Split Screen .................................................................................... 23 Timer............................................................................................... 24 Setting .................................................................................................. 24 Capture ........................................................................................... 24 Resolution ....................................................................................... 24 Quality ............................................................................................ 24 Type ................................................................................................ 25 Interval ............................................................................................ 25 Recording ....................................................................................... 25 Storage ........................................................................................... 25 Format ............................................................................................ 25 USB to PC ...................................................................................... 26 Flicker ............................................................................................. 26 System ................................................................................................. 26 Language ........................................................................................ 26 Output Display ................................................................................ 26 Backup ............................................................................................ 27 Save Setting ................................................................................... 27 Recall Setting.................................................................................. 27 Information ...................................................................................... 27 Default ............................................................................................ 27 Playback ............................................................................................... 28 Slide Show ...................................................................................... 28 Interval ............................................................................................ 28 Slide Show Effect ............................................................................ 28 Current Storage .............................................................................. 28 Delete All ........................................................................................ 28 Transfer Captured Images/Videos to a computer .............................. 29 Technical Specifications .............................................................. 29 Image .............................................................................................. 29 Optics ............................................................................................. 29 Power ............................................................................................. 30 Lighting ........................................................................................... 30 Input/Output .................................................................................... 30 Dimension ....................................................................................... 30 External Storage ............................................................................. 30 Using the RS-232 Interface .......................................................... 31 Connect to the Computer RS-232 ........................................................ 31 RS-232 Cable Specifications ................................................................ 31 RS-232 Transmission Specifications .................................................... 31 RS-232 Communication Format ........................................................... 32 RS-232 Send Command Table ............................................................. 32 RS-232 Get Command Table ............................................................... 37 Troubleshooting ............................................................................ 37 Limited Warranty ........................................................................... 38 ENGLISH
Packa ge Contents
Make sure the following items are included in the package.
RS-232/CVBS Cable
USB Cable
RCA Cable
Power Adapter (12V, 2A)
* The power adapter will vary
depending on the standard
power outlet of the country
where it is sold.
RGB Cable
AVerVision F30
RM- NM
Software & Manual CD
Remote Control
(batteries included)
Anti-glare Sheet
Optional Accessories
Microscope Adapter
28mm Rubber
Coupler
34mm Rubber
Coupler
1
Light Box
ENGLISH
G e t F a m i l i a r w i t h t h e AV e r V i s i o n F 3 0
(1)
(4)
(2)
(3)
(5)
(6)
(7)
(8)
(9)
(fig. 1.1)
Name
(1) Camera head
(2) Camera lens
(3) LED light
(4) Flexible arm
(5)
Left panel
(6)
(7)
Control panel
IR sensor
(8)
Rear panel
(9)
Right panel
Function
Contain the camera sensor.
Focus the image in the camera.
Provide light to enhance the lighting condition.
Provide adjustable viewing coverage.
Connections for microphone, speaker, USB flash drive/USB mouse,
and USB switch.
Easy access to various functions.
Receive remote control commands.
Connections for power, computer, RGB/RCA external display device,
RS-232, and USB to PC.
Connections for the camera head holder, SD card, TV-RGB display
output switch, and antitheft Kensington security lock compatible slot.
R ig ht Pa ne l
(2)
(3)
(1)
(4)
(fig. 1.2)
Name
(1) Camera Holder
(2) SD card slot
(3)
TV-RGB switch
(4)
Antitheft Slot
Function
Hold the camera head for storage.
Insert the SD card with the label facing up.
TV switch to output display video from RS232/CVBS (via RCA
connection), and RGB to RGB OUT port.
Attach a Kensington compatible security lock or antitheft device.
2
ENGLISH
Rear Pa nel
(1)
(2)
(5)
(4)
(3)
(fig. 1.3)
Function
Connect the power adapter into this port.
Input the signal from a computer or other sources and pass it
through to the RGB OUT port only. Connect this port to the
RGB/VGA output port of a computer or other sources.
Connect the AVerVision F30 to any display device with RGB
cable.
Connect the supplied RS-232/CVBS cable into this port. The
RCA jack outputs the video signal from the camera to a TV or
video equipment. The RS-232 jack is used to connect to
computer serial port or to any control panel or for centralized
control if desired.
Connect to a USB port of a computer with a USB cable and use
AVerVision F30 as a USB camera or transfer the captured
images from the memory source to computer.
Name
(1) DC12V
(2)
RGB INPUT port
(3)
RGB OUTPUT port
(4)
RS-232/CVBS port
(5)
Mini USB port
L eft P ane l
(1)
(2)
(3)
(4)
(fig. 1.4)
Name
(1)
Speaker port
(2)
MIC port
(3)
USB port
(4)
USB switch
Function
Connect to an amplified speaker to playback recorded audio &
video clip.
Connect a 3.5mm plug microphone. The built-in mic will be
disabled when an external MIC is connected to this port.
Insert a USB flash drive to save the captured images or recorded
video directly from the USB flash drive.
for saving the captured image and audio video
Switch to
when connecting
recording directly to the USB flash drive; and
AVerVision F30 to a computer using a USB cable from the rear
USB port.
3
ENGLISH
Cont rol Panel
(1)
(10)
(11)
OUTPUT
RGB
(2)
(3)
POWER
TV
RECORDING
CAMERA / PC
PLAYBACK
(12)
(4)
AUTO FOCUS
(5)
(6)
(7)
(13)
(8)
(14)
MENU
FREEZE
ROTATE
(9)
Name
(1) POWER
(2) OUTPUT LED
(3)
RECORDING
(4)
USB Switch LED
(5)
Shuttle Wheel
LAMP
CAP / DEL
(15)
(fig. 1.5)
Function
Turn the unit on/standby mode.
Indicate TV-RGB switch selection to show which port the video signal
is sent out.
ƒ TV indicates that the video signal is sent out thru RS232/CVBS
port via RCA connection.
ƒ RGB indicates the video signal is sent out thru RGB OUT port.
Start/Stop audio & video recording. Audio and video recording can be
saved on a SD card or an USB Flash drive only. See External
Memory Storage.
Indicate the USB switch selection to show which USB port is
activated.
ƒ
allowing you to use the AVerVision F30 as USB camera or
transfer the captured images from the memory source to computer.
ƒ
allowing you to save the images/video in the USB flash drive.
- Turn the shuttle wheel clockwise to zoom in and counter-clockwise
to zoom out the image in Camera and Playback mode only.
When it reaches the AVerZoom of 200%, you can still continue to
zoom in up to 8X digital zoom.
- Press the shuttle wheel ▲,▼,◄, &► to pan the image while in
zoom in mode, to make a selection on 16-thumbnail images or
move to the next or previous single full screen preview in Playback
mode, or to make a selection and adjustment on the OSD mainmenu and sub-menu (See Menu Functions for more details).
- Use ▲&▼ to increase and decrease the video playback volume.
- Use ◄&► to play the video backward and forward.
- Move the Spotlight frame and Visor screen cover.
4
ENGLISH
(1)
(10)
(11)
OUTPUT
RGB
(2)
(3)
POWER
TV
RECORDING
CAMERA / PC
PLAYBACK
(12)
(4)
AUTO FOCUS
(5)
(6)
(7)
(13)
(8)
(14)
MENU
FREEZE
ROTATE
(9)
LAMP
CAP / DEL
(15)
(fig. 1.5)
Name
(6)
(7)
FREEZE
(8) MENU
(9) ROTATE
(10) CAMERA / PC
Function
- Make a selection in Playback mode and OSD menu.
- Start/Pause video playback.
- Pause or resume image display in Camera mode.
- Stop audio & video playback in Playback mode.
Open and exit the OSD menu.
Turn the image by 90° in Camera and Playback mode.
Switch the video signal between camera or computer from the RGB
IN port.
(11) PLAYBACK
View & playback captured still images and video files.
(12) AUTO FOCUS
(13) LAMP
(14) CAP/DEL
Adjust the focus automatically.
Turn the overhead light on/off.
- Capture picture in Camera mode. In continuous capture mode,
press this button again to stop.
- Delete the selected picture/video in Playback mode.
Record audio when recording video clip. The recorded sound will be
in monophonic.
(15) Built-in MIC
5
ENGLISH
.
Remote Cont rol
The remote control requires two (2) “AAA” size batteries (supplied), make sure batteries
are installed properly before use. You can access all the features of AVerVision F30 with
the remote.
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(1)
(26 )
(25 )
(24 )
(23 )
(22 )
(21 )
(20 )
(19 )
(18 )
(14)
(17 )
(15)
(16)
Name
Function
(1)
(2)
POWER
CAMERA / PC
(3)
PLAYBACK
(4)
SPOTLIGHT
Turn the unit on/standby.
Switch between Camera and computer
mode.
- Camera mode displays the video
signal from the built-in camera.
- PC mode displays the video signal
from the RGB INPUT port of F30.
View the captured picture/video from
the memory in 16-thumbnail images.
Call the Spotlight submenu. Spotlight
overlays a box frame on the presentation
screen. You can adjust the box size and
move it around.
In the Spotlight submenu, the following
options are available.
RM-NM
ON/OFF – select to run/cancel the
(fig. 1.6)
Spotlight. Press
to move to the next
selection.
Shade – set the opacity level of the area
outside the box. The shaded area will
completely turns black when it is set to
to move to the next
level 100. Press
selection.
Color – select the Spotlight frame color.
Press
to move to the next selection.
OK – press
for the setting to take
effect. If you select ON, the frame will
appear and blink, use the ▲,▼,◄, & ►
buttons to adjust the frame size and
press
to set the desired size; and
OFF will close the submenu.
To turn off Spotlight, press
6
again.
ENGLISH
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(1)
(26 )
(25 )
(24 )
(23 )
(22 )
(21 )
(20 )
(19 )
(18 )
(14)
(17 )
(15)
(16)
Name
Function
(5)
Call the Visor submenu. Visor covers
part of the presentation screen and allow
presenter to reveal the material as
desire.
In the Visor submenu, the following
options are available.
VISOR
ON/OFF – select to run/cancel the Visor.
Press
to move to the next selection.
Shade – set the opacity level of the
covered area. The shaded area will
completely turns black when it is set to
RM-NM
level 100. Press
selection.
to move to the next
OK – press
for the setting to take
effect. If you select ON, upper part of the
presentation screen is slightly exposed.
Use the ▲,▼,◄, & ► buttons to reveal
more of the covered area; and OFF will
close the submenu.
(fig. 1.6)
(6)
SPLIT
SCREEN
(7)
PIP
(8)
SLIDE SHOW
(9)
TIMER
7
To turn off Visor, press
again.
Divide the screen into two. One side
displays the live image from the built-in
camera and the other side displays 8thumbnail size picture/video from the
memory.
Show a thumbnail size captured
picture/video from the memory at the
corner of the screen in Camera mode.
Start/Stop automatically showing the
captured picture/video one-by-one.
Call the Timer
submenu.
Select to
Start/Pause/St
op the timer
countdown
and set the
timer duration.
ENGLISH
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(1)
(26 )
(25 )
(24 )
(23 )
(22 )
(21 )
(20 )
(19 )
(18 )
(14)
(17 )
(15)
(16)
RM-NM
Name
Function
(10) CAPTURE
Capture still image in Camera mode. In
continuous capture mode, press this
button again to stop.
Start/Stop audio & video recording.
Video recording can only be saved
either in a SD memory card or a USB
flash drive.
Delete the selected picture/video in
Playback mode.
Automatically adjust and set the white
balance and exposure setting.
Adjust the brightness.
(11) RECORDING
(12) DEL
(13) AUTO IMAGE
(14) BRIGHTNESS
+/(15) DEFAULT
Reset at factory default setting.
(16) NEAR / FAR
Adjust the focus manually.
(17) ZOOM
RESET
(18) ZOOM +/-
Reset zoom level to 100%.
(fig. 1.6)
(19)
(20) ▲,▼,◄, & ►
(21) MENU
(22) AUTO
FOCUS
(23) FREEZE /
STOP
(24) ROTATE
8
- Increase/decrease the image
magnification in camera and picture
playback mode.
- Use to easily page up and page down
16-thumbnail picture preview.
- Make a selection in Playback mode
and OSD menu.
- Play/Pause video playback.
- Pan the image when image is above
10X zoom in live mode or in playback
captured image mode.
- Move the selection in Playback mode
and in OSD menu.
- Use ▲&▼ to increase and decrease
the video playback volume.
- Use ◄ &► to play the video backward
and forward.
- Move the Spotlight frame and Visor
screen cover.
Open and exit the OSD menu.
Adjust the focus automatically.
- Freeze live images.
- Stop video playback.
Rotate the image by 90° in Camera
mode and Playback mode.
ENGLISH
Name
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(1)
(26 )
(25 )
(24 )
(23 )
(22 )
(21 )
(20 )
(19 )
(18 )
(14)
(17 )
(15)
(16)
Function
(25) MODE
Select from 4 type of modes:
Sharp - adjust the contrast along
the edges making text appear more
visible.
Graphics - adjust the gradient of
image.
Motion - increase frame rate.
Sufficient lighting is required when
using this mode.
Microscope - automatically adjust
to the optimum zoom level for
microscopic viewing.
(26) LAMP
Turn the overhead light on/off.
RM-NM
(fig. 1.6)
Making the Connections
Before making the connection, make sure the power of all devices are turned off. If you
are not sure on where to connect, simply follow the illustrated connections below and also
refer to the user manual of the device you are connecting the AVerVision F30 with.
S e t t h e T V- R G B S w i t c h S e t t i n g
The TV-RGB switch determines the display output selection. Switch it to RGB (right) to
output signal using RGB connection and TV (left) to output signal using RCA connection.
(see fig. 1.2 # 3)
Switch
AVerVision Port
Display Device Port
RGB
RGB OUTPUT
RGB INPUT
To
TV
RS232/CVBS
VIDEO IN
(use RS-232/CVBS cable)
9
ENGLISH
Connect to a Monitor or LCD/DLP Pr ojector
Locate the RGB (VGA) input port of the graphics display device and connect it to RGB
OUT port of AVERVISION F30.
Make sure the TV/RGB switch is set to RGB.
RGB cable
LCD/DLP projector
RGB cable
LCD monitor
Connect to a TV
Locate the VIDEO or SCART RGB (if applicable) input port of the TV or Video equipment
(i.e., VCR) to record your presentation and connect it to RCA jack of RS-232/CVBS cable.
INPUT
RS-232/CVBS cable
Projector
VIDEO
Te l e v i s i o n
SCART
RCA cable
RCA to SCART cable
(not supplied)
VCR
10
ENGLISH
C o n n e c t i n g t h e Pow e r
Connect the power adapter to a standard 100V~240V AC power outlet. The unit
automatically in standby mode once the power is connected. Press
to turn on.
Power adapter
Wall outlet
Connect to a Computer
Locate the RGB (VGA) output port of the computer or laptop and connect it to RGB IN port
of AVerVision F30. The video signal from the RGB IN port is streamed to RGB OUT port.
- To display computer image, press Camera/PC button on the control panel
or remote control to switch AVerVision F30 to computer mode.
- For laptop to output display image, use the keyboard command (FN+F5)
to switch between the display modes. For different command, please refer
to your laptop manual.
Desktop
Laptop
RGB cable
11
ENGLISH
Connect to a Computer via USB
1.
Set the USB switch on the left panel to
and the
LED on the control panel will
light up. This enables you to use AVerVision
F30 as a USB Camera or to transfer the
captured pictures from the memory source and
to computer. Also see “Transfer File from
AVerVision F30 to PC”.
2.
Locate the USB port of the computer or laptop and connect it to PC port of
AVerVision F30.
Desktop
USB cable
Laptop
Connect an Exter nal Microphone
Plug a 3.5mm mono microphone to
port. The built-in microphone on the control panel
will be disabled when an external microphone is connected. The recorded audio will be in
monophonic sound.
Microphone
12
ENGLISH
C o n n e c t a n A m p l i f i e d S p e a ke r
Plug a 3.5mm plug amplified speaker to
supported.
port. Only the audio from the video playback is
We recommend connecting an amplified speaker to the Audio output port.
Take caution when using earphones. Adjust the volume down on the
remote to prevent hearing damage due to loudness.
Amplified Speaker
Connect to a Microscope
Connect the AVerVision F30 to a microscope enables you to examine microscopic objects
on a big screen.
1.
Change the image display mode to
Microscope. Press MENU > select
IMAGE tab > select MODE > select
(microscope) and press
.
2.
Aim the camera head at the farthest
point and press AUTO FOCUS.
3.
Adjust the focus of the microscope.
13
ENGLISH
4.
Select the appropriate rubber coupler
size for the microscope eyepiece and
insert it in the microscope adapter.
5.
Remove the microscope eyepiece from
the microscope and connect it to the
microscope adapter with the rubber
coupler inserted. Fasten the 3 bolts until
the adapter secures the eyepiece.
Microscope
Adapter
Microscope
eyepiece
For the eyepiece, we suggest using
15.5mm eye relief or higher.
6.
Attach the microscope adapter to the
AVerVision camera head. Then connect
it to the AVerVision and microscope.
Microscope
Make sure the arrow on the camera
head and microscope adapter are on
the same side to connect and twist
clockwise for the arrows to meet and
lock.
S e t t i n g U p AV e r V i s i o n F 3 0
This section provides useful tips on how to adjust the AVerVision F30 to meet your needs.
Storing and Handling
The gooseneck design allows you to freely bend the arm and store the camera head in the
camera holder. Once you have properly secured the camera head to the camera holder,
you may use the arm to carry AVerVision F30.
14
ENGLISH
Shooting Area
The shooting area can view an area of 420x297mm which allows you to show an A3
size landscape paper.
420
mm
mm
297
If the camera head is in upright position, press ROTATE on the control panel or remote
control twice to rotate the image in 180°.
To mirror the image, press MENU > select Mirror, press
15
, and select On.
ENGLISH
O ve r h e a d L i g h t
Press LAMP button on the control panel or remote control to turn on and off light.
Infrared Sensor
Aim the remote control at the infrared sensor to operate the unit.
Anti-glare Sheet
The anti-glare sheet is a special coated film that helps eliminate any
glare that maybe encountered while displaying very shiny objects or
glossy surfaces such as magazines and pictures. To use, simply
place the anti-glare sheet on top of the shiny document to reduce
reflected light.
16
ENGLISH
Exter nal Memor y Storage
AVerVision F30 supports both SD memory card and USB flash drive for more image
capture and audio & video recordings. AVerVision F30 can detect when there is an
external storage media and automatically switch to the last detected storage. If no
external storage is connected, all captured still images will be saved in the built-in memory.
Insert an SD Card
Insert the card with the contact facing down until it reaches the end. To remove
the card, push to eject and pull the card out. The supported SD card capacity is
from 1GB to 32GB (FAT32). We recommend using SDHC card with class-6 or
above for high quality recording.
SD Card
Insert a USB Flash Drive
1. Set the USB switch on the left panel
. AVerVision F30 will then
to
detect the USB flash drive and the
LED on the control panel will
light up.
2. Connect the USB flash drive in the USB slot. AVerVision F30 can support
USB flash drive from 2GB to 64GB (FAT32). Best to format the USB flash
drive using AVerVision F30 for better video recording.
USB Flash Drive
17
ENGLISH
OSD MENU
There are 4 tabs on the OSD menu: IMAGE, PRESENTATION, SETTING and SYSTEM.
In Playback mode, you can access PLAYBACK OSD menu to enable the Slide Show
feature and modify Slide Show interval and transition setting if desire.
For TV output, the RESOLUTION will be disabled in SETTING menu list.
IMAGE
PRESENTATION
SETTING
SYSTEM
PLAYBACK
18
ENGLISH
N avi g ate t h e Me n u a n d S u b m en u
1. Press MENU button on the remote or control
panel.
2. Press ► and ◄ to toggle between tabs
3. Press ▼ and ▲ to choose a selection in the
menu list.
to make a selection.
4. Press
5. Use ► and ◄ to adjust the setting or make a
selection.
6. Press
to enter submenu.
7. Press MENU to close the OSD menu.
Image
Menu Screen
Function
Brightness
Adjust brightness level manually between 0 and 63.
Contrast
Adjust the contrast level manually between 0 and 255
under bright and dark environments.
19
ENGLISH
Menu Screen
Function
Mode
Select from the various image display settings.
Sharp - adjust the contrast along the edges making
text appear more visible.
Graphics - adjust the gradient of image.
Motion - increase frame rate. Sufficient lighting is
required when using this mode.
Microscope - automatically adjust to the optimum
zoom level for microscopic viewing.
Effect
Convert the image into positive (true color), monochrome
(black and white) or negative.
Mirror
Select to flip the image in Camera mode.
Advanced
Select to set the Auto Image, Exposure, and White
Balance settings.
20
ENGLISH
Menu Screen
Function
Auto Image
Select ON or OFF to automatically adjust the white
balance and exposure setting, and correct the color and
exposure compensation.
This will also set the lamp to automatically turn on when
the light is not enough for the camera to adjust the focus.
Exposure
Select the exposure setting.
AUTO - automatically adjust the camera exposure and
the amount of light required.
MANUAL - manually adjust the exposure level. The
exposure can be adjusted up to 100.
White Balance
Select the White Balance setting for various light
conditions or color temperature.
AUTO - automatically adjust the white balance.
MANUAL - manually adjust the red and blue color level.
The color level can be adjusted up to 255.
Focus
Manually adjust the focus.
21
ENGLISH
Pr esentation
Menu Screen
Function
Spotlight
Spotlight overlays a frame on the presentation screen.
You can move the Spotlight around the presentation
screen using the ▲,▼,◄, & ► buttons. Select Execute
to call the Spotlight submenu.
In the Spotlight submenu, the following options are available.
ON/OFF – select to run/cancel the Spotlight. Press
to
move to the next selection.
Shade – set the opacity level of the area outside the box.
The shaded area will completely turns black when it is set
to level 100. Press
to move to the next selection.
Color – select the Spotlight frame color. Press
move to the next selection.
to
OK – press
for the setting to take effect. If you select
ON, the frame will appear and blink, use the ▲,▼,◄, &
► buttons to adjust the frame size and press
to set
the desired size; and OFF will close the submenu.
Visor
Visor covers the presentation
screen. The upper part of the
presentation screen is slightly
exposed. Use the ▲,▼,◄, & ►
buttons to reveal more of the
covered area. Select Execute to call
the Visor submenu.
22
ENGLISH
Menu Screen
Function
In the Visor submenu, the following options are available.
ON/OFF – select to run/cancel the Visor. Press
to move to
the next selection.
Shade – set the opacity level of the covered area. The shaded
area will completely turns black when it is set to level 100. Press
to move to the next selection.
OK – press
for the setting to take effect. If you select ON,
upper part of the presentation screen is slightly exposed. Use the
▲,▼,◄, & ► buttons to reveal more of the covered area; and
OFF will close the submenu.
PIP
Select the thumbnail playback screen location and show
the thumbnail playback screen at the corner of the
screen to recall the captured image from the memory in
Camera mode. Select OFF to cancel PIP.
Lower Left
Upper Left
Upper Right
Lower Right
Split Screen
Divide the screen into two parts. Half of the screen
displays the 8-thumbnail images and the other half
display the image from the AVerVision F30 camera.
Select the display location of the 8- thumbnail playback
images. Select OFF to cancel Split Screen.
Left
Right
Top
Below
23
ENGLISH
Menu Screen
Function
Timer
Start/Pause/Stop the timer and set the timer duration.
The timer automatically counts up after the count down
reaches zero to show the elapsed time. Even when you
switch between Playback, PC or Camera modes, the
timer will continue.
Setting
Menu Screen
Function
Capture
Select to set the capture resolution, quality, type and
interval settings.
Resolution
Select the capture size. In 3M setting, the capture
resolution size is 2592 X 1944.
Quality
Select the capture compression setting.
24
ENGLISH
Menu Screen
Function
Type
Select the capture type.
Single - capture one picture only.
Continuous - capture successive pictures.
Interval
Set the time interval for continuous capture. The length
can be set up to 600 sec (10 min).
Recording
Select the video recording compression setting.
Storage
Change the storage location. Audio & video recording
can only be saved in SD memory card or USB flash
drive.
Format
Format to delete all the data in the selected memory.
25
ENGLISH
Menu Screen
Function
USB to PC
Select the status of the AVerVision F30 when it is
connected to the computer via USB. Make sure the USB
switch on the left panel is set to
.
Camera - can be used as a computer webcam or with
our bundled software to record video and capture still
image.
Storage - transfer the captured pictures from the
memory to computer hard disk.
Flicker
Select between 50Hz or 60Hz. Some display devices
cannot handle high refresh rates. The image will flicker a
couple of times as the output is switched to another
refresh rate.
System
Menu Screen
Function
Language
Change and select different language.
Output Display
Set the resolution to display the image on screen. This
selection will be disabled in TV output mode.
26
ENGLISH
Menu Screen
Function
Backup
Copy the image from the built-in memory to SD card or
USB flash drive.
Save Setting
Save current setting in the selected profile number. Only
effect, mode, brightness and contrast settings can be
saved.
Recall Setting
Restore the setting back to the selected profile number.
Information
Display the product information.
Default
Restore all the settings into original factory default
setting.
27
ENGLISH
P l a y b a ck
Menu Screen
Function
Slide Show
Display all captured still pictures in an automated slide
show. The video file will be skipped.
Interval
Set the interval before displaying the next picture. The
length can be set up to 100 sec.
Slide Show Effect
Select the slide show transition effect.
Slide image
Wipe right
Checker down
Split Vertical Out
Wipe down
Split Horizontal In
Current Storage
Select the source of the images.
Delete All
Permanently delete all the data in selected memory
source. A Warning Message will appear. Select YES to
continue and NO to stop formatting the storage.
28
ENGLISH
Transfer Captured Images/Videos to a computer
This enables you to transfer the captured image from the built-in memory or SD to a
computer.
The instruction below MUST be read and followed BEFORE connecting
the USB cable.
1. Make sure to set the USB switch to
for the computer to detect AVerVision
F30.
2. MUST set the USB to PC as STORAGE before connecting the USB cable.
3. When “Mass Storage Start…” appears at the lower right corner of the presentation
screen, you may now connect the USB cable.
4. Upon connecting the USB cable, the system automatically detects the new removable
disk. You can now transfer the captured image(s) from the F30 built-in memory to the
computer hard disk.
Te c h n i c a l S p e c i f i c a t i o n s
Image
Sensor
1/2” CMOS
Pixel Count
3 megapixels
Frame Rate
30 fps (max.)
White Balance
Auto / Manual
Exposure
Auto / Manual
Image mode
Sharp / Graphics / Motion / Microscope
Effect
Color / B/W / Negative / Mirror / Rotate / Freeze
RGB output
1280x720, 1024x768
Image Capture
240 Frames(XGA) ; 80 Frames(3M Pixel)
Optics
Focusing
Auto / Manual
Shooting Area
420mm x 297mm
Zooming
16X (2X AVERZOOM™ + 8X Digital Zoom)
29
ENGLISH
Power
Power Source
DC 12V, 100-240V, 50-60Hz
Consumption
16.8 Watts (lamp off); 18 Watts (lamp on)
Lighting
Lamp Type
LED light
Input/Output
RGB Input
15-Pins D-sub (VGA)
RGB Output
15-Pins D-sub (VGA)
CVBS/RS-232
Mini-DIN Jack (use CVBS/RS-232 Adapter cable)
Composite Video
RCA Jack
USB
USB2.0
DC 12V Input
Power Jack
MIC
Phone Jack
Speaker
Phone Jack
Dimension
Operating
380mm x 200mm x 525mm (+/-2mm include rubber foot)
Folded
305mm x 230mm x 77mm (+/-2mm include rubber foot)
Weight
2.5 kg (about 5.513lbs)
External Storage
Secure Digital
(SDHC)
1GB ~ 32GB (FAT32)
USB Flash Drive
2GB ~ 64GB (FAT32)
30
ENGLISH
Using the RS-232 Interface
AVerVision F30 can be controlled using a computer or any centralized control panel
through RS-232 connection. The command code for RS-232 is provided for the system
integrator to be able to incorporate it with the system program.
Connect to the Computer RS-232
Locate the RS-232 port of the computer and connect it to RS-232 jack of RS-232/CVBS
cable.
RS-232/CVBS cable
RS-232 cable
(not supplied)
Desktop
Laptop
R S - 2 3 2 C a b l e Sp e c i fi c at i o n s
Make sure the RS-232 cable matches the cable specification design.
PC COM Port
DSUB-9P (Female)
5 4 3 2 1
9 8 7 6
CD 1
1
RXD 2
2 TXD
TXD 3
3 RXD
DTR 4
4
AVerVision RS-232 Port
5 SG
SG 5
DSR 6
6
RTS 7
7
CTS 8
8
RI (CI) 9
9
R S - 2 3 2 Tr a n s m i s s i o n S p e c i f i c a t i o n s
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
:1 bit
:8 bit
:1 bit
:None
:None
:9600bps
Start bit
Data bit
Stop bit
Parity bit
X parameter
Baud rate(Communication speed)
31
DSUB-9P (Female)
5 4 3 2 1
9 8 7 6
ENGLISH
R S - 2 3 2 C o m m u n i c a t i o n Fo r m a t
Send Device Code(1 Byte)
Type Code(1 Byte)
DataLength Code(1 Byte)
Data Code(1 Byte)
Data Code(2 Byte)
Data Code(3 Byte)
Receive Device Code(1 Byte)
CheckSum Code(1 Byte)
Format
Example
: 0x52
: 0x0B
: 0x03
: See the Command Table for reference.
: See the Command Table for reference.
: See the Command Table for reference.
: 0x53
: See the Command Table for reference.
: Start + Type + DataLength + Data + CheckSum
: 0x52 + 0x0B + 0x03+ 0x3 + 0x01 + 0x00 + 0x00 + 0x53 +
0x5A (Command Power)
R S - 2 3 2 S e n d C o m m a n d Ta b l e
Send Format︰0x52 + 0x0B + 0x03 + Data[0] + Data[1] + Data[2] + 0x53 + CheckSum
Receive Format︰0x53 + 0x00 + 0x02+ *2 + *3 + 0x52 + CheckSum
*1 :CheckSum = 0x0B xor 0x03 xor Data[0] xor Data[1] xor Data[2] xor 0x53
*2 :Receive data ok : 0x0B, ID error: 0x01, CheckSum error: 0x02, Not Command : 0x03,
Function fail = 0x04
*3 :Data[0], Return 0x00 if error
Function
data[0]
data[1]
data[2]
Checksum
POWER OFF
0x01
0x00
0x00
0x5a
POWER ON
0x01
0x01
0x00
0x5b
CAMERA MODE
0x02
0x00
0x00
0x59
PLAYBACK MODE
0x03
0x00
0x00
0x58
PC-1 PASS THROUGH
0x04
0x00
0x00
0x5f
IMAGE CAPTURE TYPE: SINGLE
0x05
0x00
0x00
0x5e
IMAGE CAPTURE TYPE: CONTINUOUS
0x05
0x01
0x00
0x5f
0x06
0x00
0x00
0x5d
0x06
0x01
0x00
0x5c
NORMAL IMAGE CAPTURE
0x07
0x00
0x00
0x5c
3M IMAGE CAPTURE
0x07
0x01
0x00
0x5d
TIMER START
0x08
0x00
0x00
0x53
IMAGE CAPTURE CONTINUOUS
INTERVAL INCREASE
IMAGE CAPTURE CONTINUOUS
INTERVAL DECREASE
32
ENGLISH
Function
data[0]
data[1]
data[2]
Checksum
TIMER PAUSE
0x08
0x01
0x00
0x52
TIMER STOP
0x08
0x02
0x00
0x51
*1
TIMER SET TIME
0x08
0x03
Value[ ?
~?]
PREVIEW MODE: SHARP
0x0A
0x00
0x00
0x51
PREVIEW MODE: GRAPHICS
0x0A
0x01
0x00
0x50
PREVIEW MODE: MOTION
0x0A
0x02
0x00
0x53
PREVIEW MODE: MICROSCOPE
0x0A
0x03
0x00
0x52
PREVIEW MODE CAPTURE
0x0B
0x00
0x00
0x50
PLAYBACK DELETE
0x0C
0x00
0x00
0x57
PLAYBACK FULL SCREEN
0x0D
0x00
0x00
0x56
MIRROR OFF
0x0E
0x00
0x00
0x55
MIRROR ON
0x0E
0x01
0x00
0x54
ROTATE 0
0x0F
0x00
0x00
0x54
ROTATE 90
0x0F
0x01
0x00
0x55
ROTATE 180
0x0F
0x02
0x00
0x56
ROTATE 270
0x0F
0x03
0x00
0x57
EFFECT: COLOR
0x10
0x00
0x00
0x4b
EFFECT: B/W
0x10
0x01
0x00
0x4a
EFFECT: NEGATIVE
0x10
0x02
0x00
0x49
CONTRAST INCREASE
0x11
0x00
0x00
0x4a
CONTRAST DECREASE
0x11
0x01
0x00
0x4b
CONTRAST VALUE
0x11
0x02
Value[ ?
~?]
*1
BRIGHTNESS INCREASE
0x12
0x00
0x00
0x49
BRIGHTNESS DECREASE
0x12
0x01
0x00
0x48
*1
BRIGHTNESS VALUE
0x12
0x02
Value[ ?
~?]
EXPOSURE: AUTO
0x13
0x00
0x00
0x48
EXPOSURE: MANUAL
0x13
0x01
0x00
0x49
EXPOSURE MANUAL INCREASE
0x14
0x00
0x00
0x4f
EXPOSURE MANUAL DECREASE
0x14
0x01
0x00
0x4e
33
ENGLISH
Function
data[0]
data[1]
data[2]
Checksum
WHITE BALANCE: AUTO
0x15
0x00
0x00
0x4e
WHITE BALANCE: MANUAL
0x15
0x01
0x00
0x4f
WHITE BALANCE BLUE INCREASE
0x16
0x00
0x00
0x4d
WHITE BALANCE BLUE DECREASE
0x16
0x01
0x00
0x4c
WHITE BALANCE RED INCREASE
0x17
0x00
0x00
0x4c
WHITE BALANCE RED DECREASE
0x17
0x01
0x00
0x4d
FLICKER: 50Hz
0x18
0x00
0x00
0x43
FLICKER: 60Hz
0x18
0x01
0x00
0x42
SPOTLIGHT: OFF
0x19
0x00
0x00
0x42
SPOTLIGHT: ON
0x19
0x01
0x00
0x43
SPOTLIGHT SHADE: 0% dark
0x1A
0x00
0x00
0x41
SPOTLIGHT SHADE: 50% dark
0x1A
0x01
0x00
0x40
SPOTLIGHT SHADE: 100% dark
0x1A
0x02
0x00
0x43
SPOTLIGHT COLOR: RED
0x1B
0x00
0x00
0x40
SPOTLIGHT COLOR: GREEN
0x1B
0x01
0x00
0x41
SPOTLIGHT COLOR: BLUE
0x1B
0x02
0x00
0x42
SPOTLIGHT RESIZE
0x1C
0x00
0x00
0x47
VISOR: OFF
0x1D
0x00
0x00
0x46
VISOR: ON
0x1D
0x01
0x00
0x47
VISOR SHADE: 50% dark
0x1E
0x00
0x00
0x45
VISOR SHADE: 100% dark
0x1E
0x01
0x00
0x44
PIP: OFF
0x1F
0x00
0x00
0x44
PIP: ON
0x1F
0x01
0x00
0x45
PIP POSITION: BOTTOM LEFT
0x20
0x00
0x00
0x7b
PIP POSITION: TOP LEFT
0x20
0x01
0x00
0x7a
PIP POSITION: TOP RIGHT
0x20
0x02
0x00
0x79
PIP POSITION: BOTTOM RIGHT
0x20
0x03
0x00
0x78
SPLITSCREEN: OFF
0x21
0x00
0x00
0x7a
SPLITSCREEN: ON
0x21
0x01
0x00
0x7b
SPLITSCREEN DIR: UPPER SCREEN
0x22
0x00
0x00
0x79
34
ENGLISH
Function
data[0]
data[1]
data[2]
Checksum
SPLITSCREEN DIR: LOWER SCREEN
0x22
0x01
0x00
0x78
SPLITSCREEN DIR: LEFT SCREEN
0x22
0x02
0x00
0x7b
SPLITSCREEN DIR: RIGHT SCREEN
0x22
0x03
0x00
0x7a
RECORD: OFF
0x23
0x00
0x00
0x78
RECORD: ON
0x23
0x01
0x00
0x79
MOVIE FAST REWIND
0x25
0x00
0x00
0x7e
MOVIE FAST FORWARD
0x25
0x01
0x00
0x7f
MOVIE VOL INC
0x26
0x00
0x00
0x7d
MOVIE VOL DEC
0x26
0x01
0x00
0x7c
RECORD QUALITY: NORMAL
0x27
0x00
0x00
0x7c
RECORD QUALITY: HIGH
0x27
0x01
0x00
0x7d
STORAGE: EMBEDDED
0x28
0x00
0x00
0x73
STORAGE: SD CARD
0x28
0x01
0x00
0x72
STORAGE: THUMB DRIVE
0x28
0x02
0x00
0x71
FORMAT: EMBEDDED
0x29
0x00
0x00
0x72
FORMAT: SD CARD
0x29
0x01
0x00
0x73
FORMAT: THUMB DRIVE
0x29
0x02
0x00
0x70
OUTPUT RESOLUTION: 1024x768
0x2F
0x01
0x00
0x75
OUTPUT RESOLUTION: 1280x720
0x2F
0x02
0x00
0x76
USB CONNECT: USB CAMERA
0x30
0x00
0x00
0x6b
USB CONNECT: MASS STORAGE
0x30
0x01
0x00
0x6a
BACKUP TO SD CARD
0x31
0x00
0x00
0x6a
BACKUP TO THUMBDRIVE
0x31
0x01
0x00
0x6b
PROFILE SAVE: PROFILE 1
0x32
0x00
0x00
0x69
PROFILE SAVE: PROFILE 2
0x32
0x01
0x00
0x68
PROFILE SAVE: PROFILE 3
0x32
0x02
0x00
0x6b
PROFILE RECALL: PROFILE 1
0x33
0x00
0x00
0x68
PROFILE RECALL: PROFILE 2
0x33
0x01
0x00
0x69
PROFILE RECALL: PROFILE 3
0x33
0x02
0x00
0x6a
SLIDESHOW: OFF
0x34
0x00
0x00
0x6f
35
ENGLISH
Function
data[0]
data[1]
data[2]
Checksum
SLIDESHOW: ON
0x34
0x01
0x00
0x6e
SLIDESHOW EFFECT: EFFECT 0
0x35
0x00
0x00
0x6e
SLIDESHOW EFFECT: EFFECT 1
0x35
0x01
0x00
0x6f
SLIDESHOW EFFECT: EFFECT 2
0x35
0x02
0x00
0x6c
SLIDESHOW EFFECT: EFFECT 3
0x35
0x03
0x00
0x6d
SLIDESHOW EFFECT: EFFECT 4
0x35
0x04
0x00
0x6a
SLIDESHOW EFFECT: EFFECT 5
0x35
0x05
0x00
0x6b
AUTO IMAGE:OFF
0x36
0x00
0x00
0x6d
AUTO IMAGE:ON
0x36
0x01
0x00
0x6c
CAPTURE QUALITY: STANDARD
0x37
0x00
0x00
0x6c
CAPTURE QUALITY: FINE
0x37
0x01
0x00
0x6d
CAPTURE QUALITY: FINEST
0x37
0x02
0x00
0x6e
AUTO FOCUS
0x40
0x00
0x00
0x1b
MENU
0x41
0x00
0x00
0x1a
ARROW - DOWN
0x42
0x00
0x00
0x19
ARROW – UP
0x42
0x01
0x00
0x18
ARROW - LEFT
0x42
0x02
0x00
0x1b
ARROW - RIGHT
0x42
0x03
0x00
0x1a
ENTER
0x43
0x00
0x00
0x18
FREEZE
0x44
0x00
0x00
0x1f
DEFAULT
0x45
0x00
0x00
0x1e
ZOOM -
0x46
0x00
0x00
0x1d
ZOOM +
0x46
0x01
0x00
0x1c
ZOOM RESET
0x47
0x00
0x00
0x1c
NEAR
0x48
0x00
0x00
0x13
FAR
0x48
0x01
0x00
0x12
LAMP OFF
0x49
0x00
0x00
0x12
LAMP ON
0x49
0x01
0x00
0x13
36
ENGLISH
R S - 2 3 2 G e t C o m m a n d Ta b l e
Send Format︰0x52 + 0x0A + 0x01 + Data[0] + 0x53 + CheckSum
Receive Format︰0x53 + 0x0C + 0x01 + ReData[0] + 0x53 + ReCheckSum
*1 :ReCheckSum = 0x0C xor 0x01 xor ReData[0] xor 0x52
Data[0]
CheckSum
Code
Red Value
0x02
0x5A
Value[ ? ~ ? ]
Blue Value
0x03
0x5B
Value[ ? ~ ? ]
Power Status
0x04
0x5C
0 : OFF
1: ON
Lamp Status
0x05
0x5D
0 : OFF
1: ON
Display Status
0x06
0x5E
0: Camera Mode
1: Playback Mode
2: PC-1 Pass Through
Video Output Status
0x07
0x5F
0: VGA 1: TV
Freeze Status
0x08
0x50
0 : OFF
Brightness Value
0x0A
0x52
Value[ ? ~ ? ]
Contrast Value
0x0B
0x53
Value[ ? ~ ? ]
LIGHT BOX Status
0x0C
0x54
0 : OFF
Function
ReData[0]
1: ON
1: ON
Tr o u b l e s h o o t i n g
This section provides many useful tips on how to solve common problems while using the
AVerVision F30.
There is no picture on the presentation screen.
1.
2.
3.
4.
Check all the connectors again as shown in this manual.
Check the on/off switch of the display output device.
Verify the setting of the display output device.
If you are presenting from a notebook or computer through the display output device, check the
cable connection from computer RGB (VGA) output to RGB input of AVerVision F30 and make
sure AVerVision F30 is in PC Mode.
I have set up the AVerVision F30 and checked all the connections as specified in
the manual but I cannot get a picture on the preferred presentation screen.
1. Once the power is connected the unit is set to standby mode. Press the POWER button to turn on.
2. If your display output device is on TV or any analog device, please switch the TV-RGB dip switch
to TV.
The picture on the presentation screen is distorted or the image is blurry.
1. Reset all changed settings, if any, to the original manufacturer default setting. Press MENU then
go to SYSTEM > Default and select YES in the OSD menu.
2. Use the Brightness and Contrast menu functions to reduce the distortion if applicable.
3. If you discover that the image is blurry or out of focus, press the Auto Focus button on the control
panel or remote control.
37
ENGLISH
There is no computer signal on presentation screen.
1. Check all the cable connections among the display device, AVerVision F30 and your PC.
2. Connect your PC to the AVerVision F30 first before you power on your computer.
3. For notebook, repeatedly press FN+F5 to toggles between display modes and display the
computer image on the presentation screen. For different command, please refer to your laptop
manual.
The presentation screen does not show the exact desktop image on my PC or
Notebook after I toggle from Camera to PC mode.
1. Return to your PC or Notebook, place the mouse on the desktop and right click, choose
“Properties”, choose “Setting” tab, click on “2” monitor and check the box “Extend my Windows
desktop onto this monitor”.
2. Then go back one more time to your PC or Notebook and place the mouse on the desktop and
right click again.
3. This time choose “Graphics Options”, then “Output To”, then “Intel® Dual Display Clone”, and
then choose “Monitor + Notebook”.
4. After you follow these steps, you should be able to see the same desktop image on your PC or
Notebook as well as on the presentation screen.
AVerVision F30 can’t detect the inserted USB flash drive.
Make sure the USB flash drive switch is set to
inserted.
and check if the USB flash drive is properly
Li m i ted War r anty
For a period of time beginning on the date of purchase of the applicable product and extending as set
forth in the “Warranty Period of AVer Product Purchased” section of the warranty card, AVer
Information Inc. (“AVer”) warrants that the applicable product (“Product”) substantially conforms to
AVer’s documentation for the product and that its manufacture and components are free of defects in
material and workmanship under normal use. “You” as used in this agreement means you individually
or the business entity on whose behalf you use or install the product, as applicable. This limited
warranty extends only to You as the original purchaser. Except for the foregoing, the Product is
provided “AS IS.” In no event does AVer warrant that You will be able to operate the Product without
problems or interruptions, or that the Product is suitable for your purposes. Your exclusive remedy
and the entire liability of AVer under this paragraph shall be, at AVer’s option, the repair or
replacement of the Product with the same or a comparable product. This warranty does not apply to
(a) any Product on which the serial number has been defaced, modified, or removed, or (b) cartons,
cases, batteries, cabinets, tapes, or accessories used with this product. This warranty does not apply
to any Product that has suffered damage, deterioration or malfunction due to (a) accident, abuse,
misuse, neglect, fire, water, lightning, or other acts of nature, commercial or industrial use,
unauthorized product modification or failure to follow instructions included with the Product, (b)
misapplication of service by someone other than the manufacturer’s representative, (c) any shipment
damages (such claims must be made with the carrier), or (d) any other causes that do not relate to a
Product defect. The Warranty Period of any repaired or replaced Product shall be the longer of (a) the
original Warranty Period or (b) thirty (30) days from the date of delivery of the repaired or replaced
product.
Limitations of Warranty
AVer makes no warranties to any third party. You are responsible for all claims, damages, settlements,
expenses, and attorneys’ fees with respect to claims made against You as a result of Your use or
misuse of the Product. This warranty applies only if the Product is installed, operated, maintained,
and used in accordance with AVer specifications. Specifically, the warranties do not extend to any
failure caused by (i) accident, unusual physical, electrical, or electromagnetic stress, neglect or
misuse, (ii) fluctuations in electrical power beyond AVer specifications, (iii) use of the Product with any
accessories or options not furnished by AVer or its authorized agents, or (iv) installation, alteration, or
38
ENGLISH
repair of the Product by anyone other than AVer or its authorized agents.
Disclaimer of Warranty
EXCEPT AS EXPRESSLY PROVIDED OTHERWISE HEREIN AND TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, AVER DISCLAIMS ALL OTHER WARRANTIES WITH
RESPECT TO THE PRODUCT, WHETHER EXPRESS, IMPLIED, STATUTORY OR OTHERWISE,
INCLUDING WITHOUT LIMITATION, SATISFACTORY QUALITY, COURSE OF DEALING, TRADE
USAGE OR PRACTICE OR THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE OR NONINFRINGEMENT OF THIRD PARTY RIGHTS.
Limitation of Liability
IN NO EVENT SHALL AVER BE LIABLE FOR INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
PUNITIVE, OR CONSEQUENTIAL DAMAGES OF ANY NATURE INCLUDING, BUT NOT LIMITED
TO, LOSS OF PROFITS, DATA, REVENUE, PRODUCTION, OR USE, BUSINESS INTERRUPTION,
OR PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES ARISING OUT OF OR IN
CONNECTION WITH THIS LIMITED WARRANTY, OR THE USE OR PERFORMANCE OF ANY
PRODUCT, WHETHER BASED ON CONTRACT OR TORT, INCLUDING NEGLIGENCE, OR ANY
OTHER LEGAL THEORY, EVEN IF AVER HAS ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. AVER’S TOTAL, AGGREGATE LIABILITY FOR DAMAGES OF ANY NATURE,
REGARDLESS OF FORM OF ACTION, SHALL IN NO EVENT EXCEED THE AMOUNT PAID BY
YOU TO AVER FOR THE SPECIFIC PRODUCT UPON WHICH LIABILITY IS BASED.
Governing Law and Your Rights
This warranty gives you specific legal rights; You may also have other rights granted under state law.
These rights vary from state to state.
For warranty period, please refer to the warranty card.
39
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising