- Computers & electronics
- Computer components
- System components
- Motherboards
- Vecow
- ECS-9755-440Q
- User manual
advertisement
ECS-9700/9600
Quad Core Intel
®
Xeon
®
/ Core
™
i7/ i5/ i3 Fanless Embedded System
High Performance, Rugged, Expandable, Extended Temperature
USER
Manual
1.1.0 Edition 20161114
Record of Revision
Version Date
1.0
11/14/2016
Page
All
Description
Official Release
Remark
ii
Disclaimer
This manual is released by Vecow Co., Ltd. for reference purpose only. All product offerings and specifications are subject to change without prior notice.
It does not represent commitment of Vecow Co., Ltd. Vecow shall not be liable for direct, indirect, special, incidental, or consequential damages arising out of the use of the product or documentation or any infringements upon the rights of third parties, which may result from such use.
Declaration of Conformity
FCC
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
CE
The products described in this manual complies with all applicable European
Union (CE) directives if it has a CE marking. For computer systems to remain CE compliant, only CE-compliant parts may be used. Maintaining CE compliance also requires proper cable and cabling techniques.
Copyright and Trademarks
This document contains proprietary information protected by copyright. No part of this publication may be reproduced in any form or by any means, electric, photocopying, recording or otherwise, without prior written authorization by Vecow Co., Ltd. The rights of all the brand names, product names, and trademarks belong to their respective owners.
iii
Order Information
Part Number Description
ECS-9710-505M ECS-9700, Quad Core Intel
®
Xeon
® w/ 4 PoE
+
32 Isolated DIO
E3-1505M v5, 6 GigE LAN
, 2 SSD Tray, 1 PCIe x16, 6 USB 3.0, 4 COM, 4 SIM,
ECS-9710-820Q ECS-9700, Quad Core Intel
®
4 PoE
+
Isolated DIO
Core™ i7-6820EQ, 6 GigE LAN w/
, 2 SSD Tray, 1 PCIe x16, 6 USB 3.0, 4 COM, 4 SIM, 32
ECS-9710-440Q ECS-9700, Quad Core Intel
®
4 PoE
+
Isolated DIO
Core™ i5-6440EQ, 6 GigE LAN w/
, 2 SSD Tray, 1 PCIe x16, 6 USB 3.0, 4 COM, 4 SIM, 32
ECS-9701-505M ECS-9700, Quad Core Intel
®
Xeon
® w/ 4 PoE
+
Isolated DIO
E3-1505M v5, 6 GigE LAN
, 2 SSD Tray, 1 PCI, 6 USB 3.0, 4 COM, 4 SIM, 32
ECS-9701-820Q ECS-9700, Quad Core Intel
® w/ 4 PoE
+
Isolated DIO
Core™ i7-6820EQ, 6 GigE LAN
, 2 SSD Tray, 1 PCI, 6 USB 3.0, 4 COM, 4 SIM, 32
ECS-9701-440Q ECS-9700, Quad Core Intel
® w/ 4 PoE
+
Isolated DIO
Core™ i5-6440EQ, 6 GigE LAN
, 2 SSD Tray, 1 PCI, 6 USB 3.0, 4 COM, 4 SIM, 32
ECS-9610-505M ECS-9600, Quad Core Intel
DIO
®
Xeon
®
E3-1505M v5, 2 GigE LAN,
2 SSD Tray, 1 PCIe x16, 6 USB 3.0, 4 COM, 4 SIM, 16 Isolated
ECS-9610-820Q ECS-9600, Quad Core Intel
DIO
®
Core™ i7-6820EQ, 2 GigE LAN,
2 SSD Tray, 1 PCIe x16, 6 USB 3.0, 4 COM, 4 SIM, 16 Isolated
ECS-9610-440Q ECS-9600, Quad Core Intel
DIO
®
Core™ i5-6440EQ, 2 GigE LAN,
2 SSD Tray, 1 PCIe x16, 6 USB 3.0, 4 COM, 4 SIM, 16 Isolated
ECS-9601-505M
ECS-9600, Quad Core Intel
®
Xeon
®
E3-1505M v5, 2 GigE LAN,
2 SSD Tray, 1 PCI, 6 USB 3.0, 4 COM, 4 SIM, 16 Isolated DIO
ECS-9601-820Q
ECS-9600, Quad Core Intel
®
Core™ i7-6820EQ, 2 GigE LAN,
2 SSD Tray, 1 PCI, 6 USB 3.0, 4 COM, 4 SIM, 16 Isolated DIO
ECS-9601-440Q
ECS-9600, Quad Core Intel
®
Core™ i5-6440EQ, 2 GigE LAN,
2 SSD Tray, 1 PCI, 6 USB 3.0, 4 COM, 4 SIM, 16 Isolated DIO iv
Order Accessories
Part Number
DDR4 16G
DDR4 8G
DDR4 4G
PWA-280WB-WT
PWA-160WB-WT
VESA Mount
DIN-RAIL
Rack Mount
TMK2-20P-100
TMK2-20P-500
TMB-TMBK-20P
3G Module
4G Module
WiFi & Bluetooth
Module
Description
Certified DDR4 16GB 2133MHz RAM
Certified DDR4 8GB 2133MHz RAM
Certified DDR4 4GB 2133MHz RAM
280W, 24V, 85V AC to 264V AC Power Adaptor with 3-pin
Terminal Block (7.62mm pitch), Wide Temperature -30°C to
+70°C
160W, 24V, 85V AC to 264V AC Power Adaptor with 3-pin
Terminal Block (7.62mm pitch), Wide Temperature -30°C to
+70°C
VESA Mounting Kit
DIN Rail Kit
2U Rackmount Kit
Terminal Block 20-pin to Terminal Block 20-pin Cable, 100cm
Terminal Block 20-pin to Terminal Block 20-pin Cable, 500cm
Terminal Board with One 20-pin Terminal Block Connector and DIN-Rail Mounting
Mini PCIe 3G/GPS Module with Antenna
Mini PCIe 4G/GPS Module with Antenna
Intel
®
Mini PCIe WiFi & Bluetooth Module with Antenna v
Table of Contents
CHAPTER 1
GENERAL INTRODUCTION
1.3.1 Specifications of ECS-9710
1.3.2 Specifications of ECS-9701
1.3.3 Specifications of ECS-9610
1.3.4 Specifications of ECS-9601
1.5.1 Dimensions of ECS-9710/9701
1.5.2 Dimensions of ECS-9610/9601
CHAPTER 2
GETTING TO KNOW YOUR ECS-9700/9600 13
2.2 Front Panel I/O & Functions
2.3 Rear Panel I/O & Functions
2.4 Main Board Expansion Connectors
2.5 Main Board Jumper & Deep Switch Settings
1
CHAPTER 3
SYSTEM SETUP
3.1 How to Open Your ECS-9700/9600
3.2 Installing DDR4 SO-DIMM Modules
52
vi
3.8 Mounting Your ECS-9700/9600
CHAPTER 4
BIOS SETUP
APPENDIX A : Isolated DIO Guide
APPENDIX B : Software Functions
APPENDIX C : RAID Installation Guide
APPENDIX D : Power Consumption
APPENDIX E : Supported Memory & Storage List
100
104
94
96
69
88
vii
1
GENERAL INTRODUCTION
1.1 Overview
Vecow ECS-9700/9600 Series is a high-performance, all-in-one integrated, expandable fanless embedded system. Powered by 6th generation Quad
Core Intel
Intel
®
Xeon
®
/ Core™ processor (Skylake-H) running with advanced
®
CM236 chipset, dual channel DDR4 2133MHz up to 32GB memory,
ECS-9700/9600 delivers up to 26% CPU performance improved than former generations with max 80% lower CPU power consumption; Cutting-edge Intel
®
HD Graphics P530/ 530 graphics engine supports DirectX 12, OpenGL 4.2 and
OpenCL 2.0 API, onboard dual DisplayPort and DVI-I display interface support up to Ultra HD 4K resolution, ECS-9700/9600 offers up to 22% improved graphics performance than the former generation; Multiple SATA III (6Gbps),
USB 3.0 (5Gbps), PoE (1Gbps) LAN and wireless connections make high-speed data conveying possible. Vecow ECS-9700/9600 Series Expandable Fanless
Embedded System brings you new generation system and power productivity to conquer demanding workloads in mission critical real-time embedded computing applications.
All-in-one and cable-less designs, fanless -25°C to 70°C operating temperature,
6 GigE LAN ports with 4 IEEE 802.3at (25.5W/ 48V) PoE
+
without additional power connections, 2 Front-access 2.5” SSD/ HDD trays, 4 SIM card sockets (3 front-access, 1 internal) for 3G/ 4G/ LTE/ WiFi/ GPRS/ UMTS, 1 Front-access
CFast socket, 4 SATA III supports software RAID 0, 1, 5, 10 function, 6 external
USB 3.0, 1 PCI/ PCIe x16 expansion slot, 4 COM RS-232/ 422/ 485, 4 Mini
PCIe sockets, 32 Isolated DIO, 6V to 36V wide range power input with 80V surge protection, configurable ignition power control, smart remote management features, remote power switch, EN50155 and EN50121-3-2 compliant, optional supports full function SUMIT A, B expansion, Vecow ECS-9700/9600 Series
Expandable Fanless Embedded System enables excellent performance, leading integration, user-friendly, smart manageability, mobile availability and rugged reliability possible for performance driven embedded applications.
With excellent performance, leading integrated features, smart manageability, superb mobile availability, secure power protection and rugged reliability,
Vecow ECS-9700/9600 Series Expandable Fanless Embedded System is your ideal choices for Machine Vision, Factory Automation, Robot Control, Smart
Manufacturing, Mobile DVR/ NVR, Intelligent Surveillance, Industry 4.0 and any Internet of Things (IoT) performance driven real-time embedded computing applications.
GENERAL INTRODUCTION
1
1.2 Features
• Quad Core Intel
®
Xeon
®
/ Core™ i7/ i5/ i3 Processor (Skylake-H) with CM236
Chipset supports up to 4K display
• 2 DDR4 2133MHz Memory, up to 32GB
• Fanless, -25°C to 70°C Operating Temperature
• 6 GigE LAN with 4 IEEE 802.3at PoE+ compliant, iAMT 11.0 supported
• 1 Easy-swap PCI/ PCIe x16 Expansion Slot
• 4 Mini PCIe Slot, 4 COM, 6 USB 3.0
• 4 SIM Card Socket (3 External) support 3G/ 4G/ LTE/ WiFi/ GPRS/ UMTS
• 2 Front-access 2.5" HDD/ SSD Tray, 1 CFast Socket
• 32 Isolated DIO
• Configurable Ignition Power Control
• 6V to 36V DC Power Input with 80V Surge Protection
1.3 Product Specification
1.3.1 Specifications of ECS-9710
System
Processor
Chipset
BIOS
SIO
Memory
Quad Core Intel
®
Xeon
®
E3-1505M v5/ Core™ i7-6820EQ/ i5-6440EQ Processor (Skylake-H)
Intel
®
CM236
AMI
IT8786E
• DDR4 2133MHz
• Up to 32GB
• 2 260-pin SO-DIMM Socket
I/O Interface
Serial
USB
Isolated DIO
LED
SIM Card
Expansion
Mini PCIe
4 COM RS-232/ 422/ 485 w/ auto flow control
• 6 USB 3.0 (External)
• 1 USB 2.0 (Internal)
32 Isolated DIO (16 DI, 16 DO)
Power, HDD, Wireless, PoE
4 SIM Card Socket (3 External, 1 Internal)
4 Mini PCIe Socket :
• 1 Mini PCIe Socket for PCIe/ USB/ Internal SIM Card/
Optional mSATA
• 3 Mini PCIe Socket for PCIe/ USB/ External SIM Card
©Vecow ECS-9700/ 9600 User Manual
GENERAL INTRODUCTION
2
Storage Device
Audio
Audio Codec
Audio Interface
Ethernet
LAN 1
LAN 2
PoE
LAN 3
LAN 4
LAN 5
LAN 6
Power
Input Voltage
Power Interface
Ignition Control
Remote Switch
Surge Protection
Others
TPM
Watchdog Timer
PCI/ PCIe
SUMIT A, B
Graphics
Graphics Processor
Interface
Storage
SATA mSATA
1 PCIe x16 Slot
2 SUMIT Slot (Optional)
Intel
®
HD Graphics P530/ 530
• VGA : Up to 1920 x 1200 @ 60Hz
• DVI-D : Up to 1920 x 1200 @ 60Hz
• DisplayPort 1 : Up to 4096 x 2304 @ 60Hz
• DisplayPort 2 : Up to 4096 x 2304 @ 60Hz
4 SATA III support software RAID 0, 1, 5, 10 :
• 3 SATA III (6Gbps)
• 1 SATA III co-lay with Mini PCIe (6Gbps)
4 mSATA connection :
• 3 SATA III (Mini PCIe Type, 6Gbps)
• 1 SATA III co-lay with SATA (Mini PCIe Type, 6Gbps)
• 1 CFast Socket, Push-in/ Push-out Ejector
• 2 Front-access 2.5" SSD/ HDD Tray
Realtek ALC892, 5.1 Channel HD Audio
1 Mic-in, 1 Line-out
Intel
®
I219 GigE LAN supports iAMT 11.0
Intel
®
I210 GigE LAN
GigE IEEE 802.3at (25.5W/48V) PoE
+
by Intel
®
I210
GigE IEEE 802.3at (25.5W/48V) PoE
+
by Intel
®
I210
GigE IEEE 802.3at (25.5W/48V) PoE
+
by Intel
®
I210
GigE IEEE 802.3at (25.5W/48V) PoE
+
by Intel
®
I210
6V to 36V, DC-in
3-pin Terminal Block : V+, V-, Frame Ground
16 Mode (Internal)
3-pin Terminal Block : On, Off, IGN
Up to 80V/1ms Transient Power
Optional Infineon SLB9665 supports TPM 2.0, LPC interface
Reset : 1 to 255 sec./min. per step
GENERAL INTRODUCTION
3
Smart Management
HW Monitor
Wake on LAN, PXE supported
Monitoring temperature, voltages. Auto throttling control when CPU overheats.
Software Support
OS Windows 10, Windows 8.1, Windows 7, Linux
Mechanical
Dimensions (WxDxH) 260mm x 215mm x 79mm (10.2" x 8.5" x 3.1")
Weight 3.5 kg (7.72 lb)
Mounting • Wallmount by mounting bracket
• DIN Rail Mount (Optional)
• 2U Rackmount (Optional)
Environment
Operating Temperature -25°C to 70°C (-13°F to 158°F)
Storage Temperature
Humidity
Relative Humidity
Shock
Vibration
EMC
-40°C to 85°C (-40°F to 185°F)
5% to 95% Humidity, non-condensing
95% at 70°C
• IEC 60068-2-27
• SSD : 50G @ Wallmount, Half-sine, 11ms
• IEC 60068-2-64
• SSD : 5Grms, 5Hz to 500Hz, 3 Axis
CE, FCC, EN50155, EN50121-3-2
1.3.2 Specifications of ECS-9701
System
Processor
Chipset
BIOS
SIO
Memory
Quad Core Intel
®
Xeon
®
E3-1505M v5/ Core™ i7-6820EQ/ i5-6440EQ Processor (Skylake-H)
Intel
®
CM236
AMI
IT8786E
• DDR4 2133MHz
• Up to 32GB
• 2 260-pin SO-DIMM Socket
©Vecow ECS-9700/ 9600 User Manual
GENERAL INTRODUCTION
4
I/O Interface
Serial
USB
Isolated DIO
LED
SIM Card
Expansion
Mini PCIe
PCI/ PCIe
SUMIT A, B
Graphics
Graphics Processor
Interface
Storage
SATA mSATA
Storage Device
Audio
Audio Codec
Audio Interface
Ethernet
LAN 1
LAN 2
PoE
LAN 3
LAN 4
4 COM RS-232/ 422/ 485 w/ auto flow control
• 6 USB 3.0 (External)
• 1 USB 2.0 (Internal)
32 Isolated DIO (16 DI, 16 DO)
Power, HDD, Wireless, PoE
4 SIM Card Socket (3 External, 1 Internal)
4 Mini PCIe Socket :
• 3 Full-size for PCIe/ USB/ External SIM Card/ mSATA
• 1 Full-size for PCIe/ Internal SIM Card/ mSATA
1 PCI Slot
2 SUMIT Slot (Optional)
Intel
®
HD Graphics P530/ 530
• VGA : Up to 1920 x 1200 @ 60Hz
• DVI-D : Up to 1920 x 1200 @ 60Hz
• DisplayPort 1 : Up to 4096 x 2304 @ 60Hz
• DisplayPort 2 : Up to 4096 x 2304 @ 60Hz
4 SATA III support software RAID 0, 1, 5, 10 :
• 3 SATA III (6Gbps)
• 1 SATA III co-lay with Mini PCIe (6Gbps)
4 mSATA connection :
• 3 SATA III (Mini PCIe Type, 6Gbps)
• 1 SATA III co-lay with SATA (Mini PCIe Type, 6Gbps)
• 1 CFast Socket, Push-in/ Push-out Ejector
• 2 Front-access 2.5" SSD/ HDD Tray
Realtek ALC892, 5.1 Channel HD Audio
1 Mic-in, 1 Line-out
Intel
®
I219 GigE LAN supports iAMT 11.0
Intel
®
I210 GigE LAN
GigE IEEE 802.3at (25.5W/48V) PoE
+
by Intel
®
I210
GigE IEEE 802.3at (25.5W/48V) PoE
+
by Intel
®
I210
GENERAL INTRODUCTION
5
LAN 5
LAN 6
Power
Input Voltage
GigE IEEE 802.3at (25.5W/48V) PoE
+
by Intel
®
I210
GigE IEEE 802.3at (25.5W/48V) PoE
+
by Intel
®
I210
Power Interface
Ignition Control
Remote Switch
Surge Protection
UPS
Others
TPM
6V to 36V, DC-in
3-pin Terminal Block : V+, V-, Frame Ground
16 Mode (Internal)
3-pin Terminal Block : On, Off, IGN
Up to 80V/1ms Transient Power
Supported (Optional)
Optional Infineon SLB9665 supports TPM 2.0, LPC interface
Watchdog Timer
Smart Management
HW Monitor
Reset : 1 to 255 sec./min. per step
Wake on LAN, PXE supported
Monitoring temperature, voltages. Auto throttling control when CPU overheats.
Software Support
OS Windows 10, Windows 8.1, Windows 7, Linux
Mechanical
Dimensions (WxDxH) 260mm x 215mm x 79mm (10.2" x 8.5" x 3.1")
Weight 3.5 kg (7.72 lb)
Mounting • Wallmount by mounting bracket
• DIN Rail Mount (Optional)
• 2U Rackmount (Optional)
Environment
Operating Temperature -25°C to 70°C (-13°F to 158°F)
Storage Temperature -40°C to 85°C (-40°F to 185°F)
Humidity
Relative Humidity
Shock
Vibration
EMC
5% to 95% Humidity, non-condensing
95% at 70°C
• IEC 60068-2-27
• SSD : 50G @ Wallmount, Half-sine, 11ms
• IEC 60068-2-64
• SSD : 5Grms, 5Hz to 500Hz, 3 Axis
CE, FCC, EN50155, EN50121-3-2
©Vecow ECS-9700/ 9600 User Manual
GENERAL INTRODUCTION
6
1.3.3 Specifications of ECS-9610
System
Processor
Chipset
BIOS
SIO
Memory
Quad Core Intel
®
Xeon
®
E3-1505M v5/ Core™ i7-6820EQ/ i5-6440EQ Processor (Skylake-H)
Intel
®
CM236
AMI
IT8786E
• DDR4 2133MHz
• Up to 32GB
• 2 260-pin SO-DIMM Socket
I/O Interface
Serial
USB
Isolated DIO
LED
SIM Card
Expansion
Mini PCIe
4 COM RS-232/ 422/ 485 w/ auto flow control
• 6 USB 3.0 (External)
• 1 USB 2.0 (Internal)
16 Isolated DIO (8 DI, 8 DO)
Power, HDD, Wireless
4 SIM Card Socket (3 External, 1 Internal)
PCI/ PCIe
SUMIT A, B
Graphics
Graphics Processor
Interface
4 Mini PCIe Socket :
• 3 Full-size for PCIe/ USB/ External SIM Card/ mSATA
• 1 Full-size for PCIe/ Internal SIM Card/ mSATA
1 PCIe x16 Slot
2 SUMIT Slot (Optional)
Intel
®
HD Graphics P530/ 530
• VGA : Up to 1920 x 1200 @ 60Hz
• DVI-D : Up to 1920 x 1200 @ 60Hz
• DisplayPort 1 : Up to 4096 x 2304 @ 60Hz
• DisplayPort 2 : Up to 4096 x 2304 @ 60Hz
Storage
SATA mSATA
Storage Device
4 SATA III support software RAID 0, 1, 5, 10 :
• 3 SATA III (6Gbps)
• 1 SATA III co-lay with Mini PCIe (6Gbps)
4 mSATA connection :
• 3 SATA III (Mini PCIe Type, 6Gbps)
• 1 SATA III co-lay with SATA (Mini PCIe Type, 6Gbps)
• 1 CFast Socket, Push-in/ Push-out Ejector
• 2 Front-access 2.5" SSD/ HDD Tray
GENERAL INTRODUCTION
7
Audio
Audio Codec
Audio Interface
Ethernet
LAN 1
LAN 2
Power
Input Voltage
Power Interface
Ignition Control
Remote Switch
Surge Protection
Others
TPM
Realtek ALC892, 5.1 Channel HD Audio
1 Mic-in, 1 Line-out
Intel
®
I219LM GigE LAN supports iAMT 11.0
Intel
®
I210 GigE LAN
6V to 36V, DC-in
3-pin Terminal Block : V+, V-, Frame Ground
16 Mode (Internal)
3-pin Terminal Block : On, Off, IGN
Up to 80V/1ms Transient Power
Watchdog Timer
Smart Management
HW Monitor
Software Support
OS Windows 10, Windows 8.1, Windows 7, Linux
Mechanical
Dimensions (WxDxH) 260mm x 215mm x 79mm (10.2" x 8.5" x 3.1")
Weight
Mounting
Wake on LAN, PXE supported
Monitoring temperature, voltages. Auto throttling control when CPU overheats.
3.5 kg (7.72 lb)
• Wallmount by mounting bracket
• DIN Rail Mount (Optional)
• 2U Rackmount (Optional)
Environment
Operating Temperature -25°C to 70°C (-13°F to 158°F)
Storage Temperature
Humidity
-40°C to 85°C (-40°F to 185°F)
5% to 95% Humidity, non-condensing
Relative Humidity
Shock
Vibration
EMC
Optional Infineon SLB9665 supports TPM 2.0, LPC interface
Reset : 1 to 255 sec./min. per step
95% at 70°C
• IEC 60068-2-27
• SSD : 50G @ Wallmount, Half-sine, 11ms
• IEC 60068-2-64
• SSD : 5Grms, 5Hz to 500Hz, 3 Axis
CE, FCC, EN50155, EN50121-3-2
©Vecow ECS-9700/ 9600 User Manual
GENERAL INTRODUCTION
8
1.3.4 Specifications of ECS-9601
System
Processor
Chipset
BIOS
SIO
Memory
Quad Core Intel
®
Xeon
®
E3-1505M v5/ Core™ i7-6820EQ/ i5-6440EQ Processor (Skylake-H)
Intel
®
CM236
AMI
IT8786E
• DDR4 2133MHz
• Up to 32GB
• 2 260-pin SO-DIMM Socket
I/O Interface
Serial
USB
Isolated DIO
LED
SIM Card
Expansion
Mini PCIe
4 COM RS-232/ 422/ 485 w/ auto flow control
• 6 USB 3.0 (External)
• 1 USB 2.0 (Internal)
16 Isolated DIO (8 DI, 8 DO)
Power, HDD, Wireless
4 SIM Card Socket (3 External, 1 Internal)
PCI/ PCIe
SUMIT A, B
Graphics
Graphics Processor
Interface
4 Mini PCIe Socket :
• 3 Full-size for PCIe/ USB/ External SIM Card/ mSATA
• 1 Full-size for PCIe/ Internal SIM Card/ mSATA
1 PCI Slot
2 SUMIT Slot (Optional)
Intel
®
HD Graphics P530/ 530
• VGA : Up to 1920 x 1200 @ 60Hz
• DVI-D : Up to 1920 x 1200 @ 60Hz
• DisplayPort 1 : Up to 4096 x 2304 @ 60Hz
• DisplayPort 2 : Up to 4096 x 2304 @ 60Hz
Storage
SATA mSATA
Storage Device
4 SATA III support software RAID 0, 1, 5, 10 :
• 3 SATA III (6Gbps)
• 1 SATA III co-lay with Mini PCIe (6Gbps)
4 mSATA connection :
• 3 SATA III (Mini PCIe Type, 6Gbps)
• 1 SATA III co-lay with SATA (Mini PCIe Type, 6Gbps)
• 1 CFast Socket, Push-in/ Push-out Ejector
• 2 Front-access 2.5" SSD/ HDD Tray
GENERAL INTRODUCTION
9
Audio
Audio Codec
Audio Interface
Ethernet
LAN 1
LAN 2
Power
Input Voltage
Power Interface
Ignition Control
Remote Switch
Surge Protection
Others
TPM
Realtek ALC892, 5.1 Channel HD Audio
1 Mic-in, 1 Line-out
Intel
®
I219LM GigE LAN supports iAMT 11.0
Intel
®
I210 GigE LAN
6V to 36V, DC-in
3-pin Terminal Block : V+, V-, Frame Ground
16 Mode (Internal)
3-pin Terminal Block : On, Off, IGN
Up to 80V/1ms Transient Power
Watchdog Timer
Smart Management
HW Monitor
Software Support
OS Windows 10, Windows 8.1, Windows 7, Linux
Mechanical
Dimensions (WxDxH) 260mm x 215mm x 79mm (10.2" x 8.5" x 3.1")
Weight
Mounting
Wake on LAN, PXE supported
Monitoring temperature, voltages. Auto throttling control when CPU overheats.
3.5 kg (7.72 lb)
• Wallmount by mounting bracket
• DIN Rail Mount (Optional)
• 2U Rackmount (Optional)
Environment
Operating Temperature -25°C to 70°C (-13°F to 158°F)
Storage Temperature
Humidity
-40°C to 85°C (-40°F to 185°F)
5% to 95% Humidity, non-condensing
Relative Humidity
Shock
Vibration
EMC
Optional Infineon SLB9665 supports TPM 2.0, LPC interface
Reset : 1 to 255 sec./min. per step
95% at 70°C
• IEC 60068-2-27
• SSD : 50G @ Wallmount, Half-sine, 11ms
• IEC 60068-2-64
• SSD : 5Grms, 5Hz to 500Hz, 3 Axis
CE, FCC, EN50155, EN50121-3-2
©Vecow ECS-9700/ 9600 User Manual
GENERAL INTRODUCTION
10
1.4 Supported CPU List
Processor No.
Xeon
®
E3-1575M v5
Xeon
®
E3-1545M v5
Xeon
®
E3-1535M v5
Xeon
®
E3-1515M v5
Xeon
®
E3-1505M v5
Xeon
®
E3-1505L v5
TDP
45W
45W
45W
45W
45W
25W
Cache
8M
8M
8M
8M
8M
8M
Core i7-6970HQ
Core i7-6920HQ
Core i7-6870HQ
Core i7-6820HQ
Core i7-6770HQ
Core i7-6700HQ
Core i7-6820EQ
Core i7-6822EQ
Core i5-6440HQ
Core i5-6350HQ
Core i5-6300HQ
Core i5-6440EQ
Core i5-6442EQ
45W
45W
45W
25W
45W
45W
45W
45W
45W
45W
45W
45W
45W
6M
6M
8M
8M
8M
8M
8M
8M
6M
6M
6M
6M
6M
Max. Frequency
Up to 3.00 GHz
Up to 2.90 GHz
Up to 2.80 GHz
Up to 2.80 GHz
Up to 2.80 GHz
Up to 2.00 GHz
Up to 3.70 GHz
Up to 3.80 GHz
Up to 3.60 GHz
Up to 3.60 GHz
Up to 3.50 GHz
Up to 3.50 GHz
Up to 3.50 GHz
Up to 2.80 GHz
Up to 3.50 GHz
Up to 3.20 GHz
Up to 3.20 GHz
Up to 3.40 GHz
Up to 2.70 GHz
Embedded
Yes
Yes
Yes
GENERAL INTRODUCTION
11
1.5 Mechanical Dimension
1.5.1 Dimensions of ECS-9710/9701
297.0 (11.69”)
282.0 (11.10”)
260.0 (10.24”)
1.5.2 Dimensions of ECS-9610/9601
297.0 (11.69”)
282.0 (11.10”)
260.0 (10.24”)
155.0 (6.10”) 215.0 (8.46”)
Unit: mm (inch)
155.0 (6.10”) 215.0 (8.46”)
Unit: mm (inch)
©Vecow ECS-9700/ 9600 User Manual
GENERAL INTRODUCTION
12
2
GETTING TO KNOW YOUR ECS-9700/9600
2.1 Packing List
Item Description
1 ECS-9700/9600 Expandable Fanless Embedded System
(According to the configuration you order, the ECS-9700/9600 series may contain SSD/HDD and DDR4 SO-DIMM. Please verify these items if necessary.)
2
3
ECS-9700-Accessory box, which contains
● Vecow Drivers & Utilities DVD
● Wall-mounting bracket
● KHS#6-32x6 screw for wall-mounting bracket
● M2.5x6 screw for Mini PCIe Slot
● Din-Rail-PH-M4x16.5-S Ni
● 3-pin pluggable terminal block
● 20-pin pluggable terminal block
● Foot Pad
● F-M3x4 for SSD/HDD screws
ECS-9600-Accessory box, which contains
● Vecow Drivers & Utilities DVD
● Wall-mounting bracket
● KHS#6-32x6 screw for wall-mounting bracket
● M2.5x6 screw for Mini PCIe Slot
● Din-Rail-PH-M4x16.5-S Ni
● 3-pin pluggable terminal block
● 20-pin pluggable terminal block
● Foot Pad
● F-M3x4 for SSD/HDD screws
Qty
1
2
4
4
2
4
4
4
1
2
1
4
4
2
4
4
4
1
2
GETTING TO KNOW YOUR ECS-9700/ 9600
13
2.2 Front Panel I/O & Functions
In Vecow ECS-9700/9600 series family, all I/O connectors are located on front panel and rear panel. Most of the general connections to computer device, such as USB, LAN Jack, Audio, VGA, Display, DVI-D and any additional storage, are placed on the front panel.
RST
SIM 1
1
WLAN
2
SIM 2
CFast
3
SIM 3
4
DVI-D
VGA
DP LAN 1
LAN 2
2.2.1 Power Button
RST
SIM 1
1
WLAN
2
SIM 2
CFast
3
SIM 3
4
DVI-D
VGA
DP LAN 1
LAN 2
The Power Button is a non-latched switch with dual color LED indication. It indicates power status: S0, S3 and S5. More detail LED indications are listed as follows:
LED Color
Solid Blue
Solid Orange
Power Status
S0
S3, S5
System Status
System working
Suspend to RAM, System off with standby power
To power on ECS-9700, press the power button and then the blue LED is lightened. To power off ECS-9700, you can either command shutdown by OS operation, or just simply press the power button.
If system error, you can just press the power button for 4 seconds to shut down the machine directly. Please do note that a 4-second interval between each
2 power-on/ power-off operation is necessary in normal working status. (For example, once turning off ECS-9700, you have to wait for 4 seconds to initiate another power-on operation).
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
14
2.2.2 Reset Tact Switch
RST
SIM 1
1
WLAN
2
SIM 2
CFast
3
SIM 3
4
DVI-D
VGA
DP LAN 1
LAN 2
It is a hardware reset switch. Use this switch to reset ECS-9700 without power off. Press the Reset Switch for a few seconds, then reset will be enabled.
2.2.3 CFast Card
RST
SIM 1
1
WLAN
2
SIM 2
CFast
3
SIM 3
4
DVI-D
VGA
DP LAN 1
LAN 2
There is a CFast socket on the front panel supporting Type-I/II Compact
Flash card. It is implemented by a SATA III Port from CM236 PCH. Be sure to disconnect the power source and unscrew the CFast socket cover before installing a CFast card. The ECS-9700 does not support the CFast hot swap and PnP (Plug and Play) functions. It is necessary to remove power source first before inserting or removing the CFast card.
The pinouts of CFast port are listed as follows:
Pin No.
S4
S5
S6
S1
S2
S3
S7
Description
GND
SATA_TXP5
SATA_TXN5
GND
SATA_RXN5
SATA_RXP5
GND
Pin No.
PC6
PC7
PC8
PC9
PC10
PC11
PC12
Description
NC
GND
CFAST_LED
NC
NC
NC
NC
GETTING TO KNOW YOUR ECS-9700/ 9600
15
Pin No.
PC1
PC2
PC3
PC4
PC5
Description
GND
GND
NC
NC
NC
2.2.4 PWR and HDD LED Indicator
Pin No.
PC13
PC14
PC15
PC16
PC17
Description
+3.3V
+3.3V
GND
GND
NC
RST
SIM 1
1
WLAN
2
SIM 2
CFast
3
SIM 3
4
DVI-D
VGA
DP LAN 1
LAN 2
HDD LED/ Yellow: A Hard Disk/ CFast LED. If the LED is on, it indicates ECS-
9700 storage is functional. If it is off, it indicates ECS-9700 storage is not functional. If it is flashing, it indicates data access activities.
Power LED/ Green: If the LED is solid green, it indicates ECS-9700 is powered on.
LED Color Power Status
Yellow
Green
HDD/ CFast
Power
System Status
• On/ Off : Storage status, function or not.
• Twinkling : Data transferring.
System power status (on/ off)
2.2.5 DVI-D Connector
RST
SIM 1
1
WLAN
2
SIM 2
CFast
3
SIM 3
4
DVI-D
VGA
DP LAN 1
LAN 2
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
16
The DVI-D connector on the front panel supports DVI display. This connector can output DVI signal. The DVI output mode supports up to 1920 x 1200 resolution and the DVI is automatically selected according to the display device connected. You will need a DVI-D cable when connecting to a display device.
2.2.6 VGA Connector
RST
SIM 1
1
WLAN
2
SIM 2
CFast
3
SIM 3
4
DVI-D
VGA
DP LAN 1
LAN 2
The VGA connector on the front panel supports VGA display. This VGA connector comes from eDP and the VGA output mode supports up to 1920 x
1200 resolution.
Remark: This VGA connector does not support Hot Plug function. If you would like to use the VGA connector, please remain the connection of VGA Display.
2.2.7 DisplayPort
RST
SIM 1
1
WLAN
2
SIM 2
CFast
3
SIM 3
4
DVI-D
VGA
DP LAN 1
LAN 2
Onboard Display Port supports auxiliary channel dual mode and the connection supports up to 4096x2304 resolution at 60 Hz.
Multi-Stream Transport Display Resolutions Table:
Multi-Stream Transport Display
One panel Display
Two panel Displays concurrently
Three panel Displays concurrently
Max. Resolution
4096x2304@60Hz
2880x1800@60Hz
2304x1440@60Hz
GETTING TO KNOW YOUR ECS-9700/ 9600
17
2.2.8 USB 3.0
RST
SIM 1
1
WLAN
2
SIM 2
CFast
3
SIM 3
4
DVI-D
VGA
DP LAN 1
LAN 2
There are 4 USB 3.0 connections available supporting up to 5GB per second data rate in the front side of ECS-9700/9600. It is also compliant with the requirements of Super Speed (SS), high speed (HS), full speed (FS) and low speed (LS).
2.2.9 Ethernet Port
RST
SIM 1
1
WLAN
2
SIM 2
CFast
3
SIM 3
4
DVI-D
VGA
DP LAN 1
LAN 2
There are 2 8-pin RJ-45 jacks supporting 10/100/1000 Mbps Ethernet connections in the front side. LAN 1 is powered by Intel i219 Ethernet Phy; LAN
2 is powered by Intel I210 Ethernet engine. When both LAN 1 and LAN 2 work in normal status, iAMT 11.0 function is enabled.
Using suitable RJ-45 cable, you can connect the system to other computers, or to any other devices with Ethernet connection; for example, a hub or a switch.
Moreover, both LAN 1 and LAN 2 support Wake on LAN and Pre-boot functions.
The pin-outs of LAN 1 and LAN 2 are listed as follows:
Pin No.
1
2
3
10/ 100Mbps
E_TX+
E_TX-
E_RX+
1000Mbps
MDI0_P
MDI0_N
MDI1_P
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
18
4
5
6
7
8
----
-----
E_RX-
-----
------
MDI2_P
MDI2_N
MDI1_N
MDI3_P
MDI3_N
Each LAN port is supported by standard RJ-45 connector with LED indicators to present Active/ Link/ Speed status of the connection.
The LED indicator on the right bottom corner lightens in solid green when the cable is properly connected to a 100 Mbps Ethernet network,and it lightens in solid orange when the cable is properly connected to a 1000Mbps Ethernet network. The left LED will keep twinkling/ off when Ethernet data packets are being transmitted/ received.
1 8
Right
Bottom Led
Left
Bottom Led
10Mbps
Off
Flash
Yellow
100Mbps
Solid
Green
Flash
Yellow
1000Mbps
Solid
Orange
Flash
Yellow
2.2.10 Audio Jack
RST
SIM 1
1
WLAN
2
SIM 2
CFast
3
SIM 3
4
DVI-D
VGA
DP LAN 1
LAN 2
There are 2 audio connectors, Mic-in and Line-out, in the front side of ECS-9700.
Onboard Realtek ALC892 audio codec supports 5.1 channel HD audio and fully complies with Intel
®
High Definition Audio (Azalia) specifications.
To utilize the audio function in Windows platform, you need to install corresponding drivers for both Intel CM236 chipset and Realtek ALC892 codec.
GETTING TO KNOW YOUR ECS-9700/ 9600
19
2.2.11 WLAN LED, Mini PCIe, SIM Card Comparison
RST
SIM 1
1
WLAN
2
SIM 2
CFast
3
SIM 3
4
DVI-D
VGA
DP LAN 1
LAN 2
Mini PCIe Slot/ SIM Slot/ WLAN LED Mapping Table :
Mini PCIe
Mini PCIe 1 / mSATA (CN12)
Mini PCIe 2 / mSATA (CN8)
Mini PCIe 3 / mSATA (CN10)
Mini PCIe 4 / mSATA (CN6)
SIM
SIM 1 (CN13)
SIM 2 (CN9)
SIM 3 (CN11)
SIM 4 (CN7)
LED
1
2
3
4
Mini PCIe 3
CN10
Mini PCIe 2
CN8
SIM4
CN6
Mini PCIe 4
CN6
Mini PCIe 1
CN12
SW2
SIM2
CN9
Note:
A. The SIM card sockets do not support hot-plug. Please make sure to unplug
the system power before inserting the SIM card(s).
SW2: Mini PCIe 1to 4; PCIe & mSATA Select SW
DIP Switch
SW2-1
Mini PCIe 1
SW2-2
Mini PCIe 2
Interface
ON Mini PCIe
OFF Auto Detection
(Default)
ON Mini PCIe
OFF Auto Detection
(Default)
DIP Switch
SW2-3
Mini PCIe 3
SW2-4
Mini PCIe 4
Interface
ON Mini PCIe
OFF Auto Detection
(Default)
ON Mini PCIe
OFF Auto Detection
(Default)
B. Mini PCIe 4 only supports PCIe interface SIM card module
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
20
2.2.12 SSD/ HDD Tray
RST
SIM 1
1
WLAN
2
SIM 2
CFast
3
SIM 3
4
DVI-D DP LAN 1
VGA
LAN 2
HDD 1
HDD 2
There are 2 front-access 2.5” SSD/ HDD trays in the front side of ECS-9700.
Just trigger to open the SSD/ HDD tray, up to 8TB is available.
HDD Tray
HDD 1
HDD 2
MB Connector
SATA1
SATA2
SATA3
SATA4
(Remark: By MB BOM Optional,
Default no signal link)
MB Power Connector
Power Conn 1
Power Conn 1
Power Conn 2
Power Conn 2
SATA3 SATA1
SATA4 SATA2
SATA Power Conn1
SATA Power Conn2
GETTING TO KNOW YOUR ECS-9700/ 9600
21
2.3 Rear Panel I/O & Functions
2.3.1 Power Terminal Block
DC-IN
V+ V-
IGN On | Off
COM 4
COM 2
COM 1
COM 3
PoE
LAN6
PoE
LAN5
PoE
LAN4
PoE
LAN3
20
DIO 2
Isolated
11 20
DIO 1
Isolated
11
10
PIN 1 ~ 8 D I
1
PIN 11 ~ 18 DO
10
PIN 1 ~ 8 D I
1
PIN 11 ~ 18 DO
This system supports 6V to 36V DC power input by terminal block in the rear side. In normal power operation, power LED lightens in solid green and supports up to 80V surge protection.
Pin No.
1
3
Definition
V+
Chassis Ground
Pin No.
2
Definition
V-
2.3.2 Remote Power On/ Off Switch & Ignition
DC-IN
V+ V-
IGN On | Off
COM 4
COM 2
COM 1
COM 3
PoE
LAN6
PoE
LAN5
PoE
LAN4
PoE
LAN3
20
DIO 2
Isolated
11 20
DIO 1
Isolated
11
10
PIN 1 ~ 8 D I
1
PIN 11 ~ 18 DO
10
PIN 1 ~ 8 D I
1
PIN 11 ~ 18 DO
It is a 5-pin power-on or power-off switch through Phoenix Contact terminal block. You could turn on or off the system power by using this contact. This terminal block supports dual function of soft power-on/ power-off (instant off or delay 4 second), and suspend mode.
Pin No.
1
3
Definition
Ignition
External Power Button V-
Pin No.
2
Definition
External Power Button V+
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
22
2.3.3 COM Ports
DC-IN
V+ V-
IGN
On | Off
COM 4
COM 2
COM 1
COM 3
PoE
LAN6
PoE
LAN5
PoE
LAN4
PoE
LAN3
20
DIO 2
Isolated
11 20
DIO 1
Isolated
11
10
PIN 1 ~ 8 D I
1
PIN 11 ~ 18 DO
10
PIN 1 ~ 8 D I
1
PIN 11 ~ 18 DO
Serial port 1 to 4 (COM 1 to 4) can be configured for RS-232, RS-422, or RS-
485 with auto flow control communication. The default definition of COM 1 and
COM 2 is RS-232. If you want to change to RS-422 or RS-485, you can find the setting in BIOS.
BIOS Setting Function
RS-232
COM 1
RS-422 (5-wire)
COM 2
RS-422 (9-wire)
COM 3
RS-485
COM 4
RS-485 w/z auto-flow control
The pin assignments are listed in the table as below:
Serial
Port
1 to 4
Pin No.
6
7
4
5
8
9
1
2
3
RS-232
DCD
RXD
TXD
DTR
GND
DSR
RTS
CTS
RI
RS-422
(5-wire)
TXD-
TXD+
RXD+
RXD-
GND
-----------
-----------
-----------
-----------
RS-422
(9-wire)
TXD-
TXD+
RXD+
RXD-
GND
RTS-
RTS+
CTS+
CTS-
RS-485
(3-wire)
DATA-
DATA+
-----------
-----------
GND
-----------
-----------
-----------
-----------
GETTING TO KNOW YOUR ECS-9700/ 9600
23
COM3 & COM 4 MB connector table:
COM Port
COM 3
MB Connector
CN27
COM 3 & COM 4 MB connector pin out:
CN
CN27(COM3)
CN28(COM4)
6
7
4
5
Pin No.
1
2
3
8
9
10
COM Port
COM 4
MB Connector
CN28
Signal Name
Chassis GND
GND
RI
DTR
CTS
TXD
RTS
RXD
DSR
DCD
CN27
COM3
CN28
COM4
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
24
2.3.4 Rear USB 3.0
DC-IN
V+ V-
IGN
On | Off
COM 4
COM 2
COM 1
COM 3
PoE
LAN6
PoE
LAN5
PoE
LAN4
PoE
LAN3
20
DIO 2
Isolated
11 20
DIO 1
Isolated
11
10
PIN 1 ~ 8 D I
1
PIN 11 ~ 18 DO
10
PIN 1 ~ 8 D I
1
PIN 11 ~ 18 DO
There are 2 USB 3.0 connections available supporting up to 5GB per second data rate in the front side of ECS-9700. It also compliant with the requirements of Super Speed (SS), high speed (HS), full speed (FS) and low speed (LS).
2.3.5 PoE (Power over Ethernet) Ports
DC-IN
V+ V-
IGN On | Off
COM 4
COM 2
COM 1
COM 3
PoE
LAN6
PoE
LAN5
PoE
LAN4
PoE
LAN3
20
DIO 2
Isolated
11 20
DIO 1
Isolated
11
10
PIN 1 ~ 8 D I
1
PIN 11 ~ 18 DO
10
PIN 1 ~ 8 D I
1
PIN 11 ~ 18 DO
There are 4 8-pin POE RJ-45 jacks supporting 10/100/1000 Mbps Ethernet connections in the front side powered by Intel I210 Ethernet engine. When both
LAN 1 and LAN 2 work in normal status, iAMT 11.0 function is enabled. Each
POE supports 30.4W
Using suitable RJ-45 cable, you can connect the system to other computers, or to any other devices with Ethernet connection; for example, a hub or a switch.
Moreover, both LAN 1 and LAN 2 support Wake on LAN and Pre-boot functions.
The pin-outs of LAN 1 and LAN 2 are listed as follows:
Pin No.
7
8
5
6
3
4
1
2
10/ 100 Mbps
E_TX+
E_TX-
E_RX+
----
-----
E_RX-
-----
------
1000 Mbps
MDI0_P
MDI0_N
MDI1_P
MDI2_P
MDI2_N
MDI1_N
MDI3_P
MDI3_N
PoE
PoE+
PoE+
PoE-
----
----
PoE-
----
----
GETTING TO KNOW YOUR ECS-9700/ 9600
25
Each LAN port is supported by standard RJ-45 connector with LED indicators to present Active/ Link/ Speed status of the connection.
The LED indicator on the right bottom corner lightens in solid green when the cable is properly connected to a 100 Mbps Ethernet network, and it lightens in solid orange when the cable is properly connected to a 1000 Mbps Ethernet network. The left LED will keep twinkling/ off when Ethernet data packets are being transmitted/ received.
LED Status 10Mbps 100Mbps 1000Mbps
1 8
Right
Bottom Led
Left
Bottom Led
Off
Flash
Yellow
Solid
Green
Flash
Yellow
Solid
Orange
Flash
Yellow
POE LED indicator:
LED Location
LAN3
LAN4
LAN5
LAN6
LED Color
Green
Green
Green
Green
Status
Green Light: PD installed & powered green
Off: Non PD
Green Light: PD installed & powered green
Off: Non PD
Green Light: PD installed & powered green
Off: Non PD
Green Light: PD installed & powered green
Off: Non PD
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
26
2.3.6 Isolated DIO
DC-IN
V+ V-
IGN
On | Off
COM 4
COM 2
COM 1
COM 3
PoE
LAN6
PoE
LAN5
PoE
LAN4
PoE
LAN3
20
DIO 2
Isolated
11 20
DIO 1
Isolated
11
10
PIN 1 ~ 8 D I
1
PIN 11 ~ 18 DO
10
PIN 1 ~ 8 D I
1
PIN 11 ~ 18 DO
There is a 32-bit (16-bit DI, 16-bit DO) with 2 DIO connectors in the rear side. DI
/ DIO support NPN(sink) and PNP(Source) mode, Each DI channel is equipped with a photocouper for isolated protection. Each DO with isolator chip is configured by a Jumper for each DIO connector. DO Safety-Related Certifications:
• 4242-VPK Basic Isolation per DIN V VDE V 0884-10
and DIN EN 61010-1
• 3-KVRMS Isolation for 1 minute per UL 1577
• CSA Component Acceptance Notice 5A, IEC
60950-1 and IEC 61010-1 End Equipment Standards
• GB4943.1-2011 CQC Certified
20
10
PIN 1 ~ 8
DIO
Isolated
D I
11
PIN 11 ~ 18
1
DO
DIO Connectors pin out:
DIO
DIO1
Pin No.
13
14
15
16
9
10
11
12
17
18
19
20
7
8
5
6
3
4
1
2
Definition
INPUT 0
INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT 5
INPUT 6
INPUT 7
DI1_COM
DIO1_GND
OUTPUT 0
OUTPUT 1
OUTPUT 2
OUTPUT 3
OUTPUT 4
OUTPUT 5
OUTPUT 6
OUTPUT 7
DIO1_GND
DIO1_VDC (6~48V Input)
Function
SIO_GPI80
SIO_GPI81
SIO_GPI82
SIO_GPI83
SIO_GPI84
SIO_GPI85
SIO_GPI86
SIO_GPI87
-
-
SIO_GPO70
SIO_GPO71
SIO_GPO72
SIO_GPO73
SIO_GPO74
SIO_GPO75
SIO_GPO76
SIO_GPO77
-
-
GETTING TO KNOW YOUR ECS-9700/ 9600
27
DIO
DIO2
Pin No.
13
14
15
16
9
10
11
12
17
18
19
20
7
8
5
6
3
4
1
2
DI reference circuit:
Sink Mode (NPN)
Power
Supply
6-48V DC
Definition
INPUT 8
INPUT 9
INPUT 10
INPUT 11
INPUT 12
INPUT 13
INPUT 14
INPUT 15
DI2_COM
DIO2_GND
OUTPUT 8
OUTPUT 9
OUTPUT 10
OUTPUT 11
OUTPUT 12
OUTPUT 13
OUTPUT 14
OUTPUT 15
DIO2_GND
DIO2_VDC (6~48V Input)
V+
DIO Connector
DI_COM (Pin 9)
Function
SIO_GPI37
SIO_GPI50
SIO_GPI51
SIO_GPI52
SIO_GPI56
SIO_GPI57
SIO_GPI64
SIO_GPI65
-
-
SIO_GPO11
SIO_GPO12
SIO_GPO15
SIO_GPO16
SIO_GPO32
SIO_GPO33
SIO_GPO35
SIO_GPO36
-
-
V-
DI (Pin1-8)
Source Mode (PNP)
Power
Supply
6-48V DC
V+
V-
DIO Connector
DI_COM (Pin 9)
DI (Pin1-8)
DO Jumper Setting Table:
DIO Jumper Setting
DIO1 JP10 1-2 (Default)
DIO1
DIO2
DIO2
JP10
JP11
JP11
2-3
1-2 (Default)
2-3
©Vecow ECS-9700/ 9600 User Manual
Status
NPN (Sink Mode):
Max. Input current 100mA / 6 ~48V
PNP (Source Mode):
Max. output current 100mA / 6 ~48V
NPN (Sink Mode):
Max. Input current 100mA / 6 ~48V
PNP (Source Mode):
Max. output current 100mA / 6 ~48V
GETTING TO KNOW YOUR ECS-9700/ 9600
28
JP11 JP10
DO reference circuit:
Sink Mode
(NPN, Default)
Device
6-48V DC
V+
IO
V-
Source Mode
(PNP)
Device
6-48V DC
V+
IO
V-
DIO Connector
DIO_VDC (Pin 20)
DO (Pin11-18)
DIO_GND (Pin10,19)
DIO Connector
DIO_VDC (Pin 20)
DO (Pin11-18)
DIO_GND (Pin10,19)
2.3.7 Add Card
DC-IN
V+ V-
IGN On | Off
COM 4
COM 2
COM 1
COM 3
PoE
LAN6
PoE
LAN5
PoE
LAN4
PoE
LAN3
20
DIO 2
Isolated
11 20
DIO 1
Isolated
11
10
PIN 1 ~ 8 D I
1
PIN 11 ~ 18 DO
10
PIN 1 ~ 8 D I
1
PIN 11 ~ 18 DO
Optional for PCIEx16 FHHL add on card or PCI card.
GETTING TO KNOW YOUR ECS-9700/ 9600
29
2.4 Main Board Expansion Connectors
2.4.1 Inside View of ECS-9700 Main Board With Connector Location
CN36
CN20
CN10
JP5 JP6
JP9
SATA3
SATA4
SATA1
SATA2
J3
J2
JP2
J9
U3 U2
CN1
CN8
J8
FN1
J7
JP11 JP10
SW3 SW4
JP7
JP8
J6
SW7
CN27 CN28
J1
CN5
CN3
SW2
JP1
CN7
CN6
JP3
JP4
J5
CN2
J10
SW5
BZ1
CN12
BAT
CFast
SW11
CN9
J11
SUMITB
SUMITA
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
30
2.4.2 UPS Power Connector
For UPS module optional, we use 4.2mm 2x2p power connector.
This system has a UPS power input connector for Optional part UPS Module.
CN36
Pin No.
1
3
Definition
Ground
+VDC_IN
(6~36V, Max.8A)
Pin No.
2
4
Definition
Ground
+VDC_IN
(6~36V, Max.8A)
2.4.3 Miscellaneous Pin Header
2.0mm 2x4p header
This pin header can be used as a backup for following functions, such as hard drive LED indicator, reset button, power LED indicator, and power-on/ off button, which already can be accessed by front panel and top panel. The pin-outs of
Miscellaneous port are listed in following table:
J11
GETTING TO KNOW YOUR ECS-9700/ 9600
31
Group
HDD LED
RESET BUTTON
POWER LED
POWER BUTTON
4
6
7
2
8
Pin No.
1
3
5
Description
HDD_LED_P
HDD_LED_N
FP_RST_BTN_N
Ground
PWR_LED_P
PWR_LED_N
FP_PWR_BTN_IN
Ground
2.4.4 DDR4 Slot
There are 2 DDR4 channel onboard and support DDR4 2133/1866, max 32GB.
(each channel 16GB)
U3 U2
Slot
Slot1 / U2
Description
DDR4 Channel A
Slot
Slot2 / U3
Description
DDR4 Channel B
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
32
2.4.5 BIOS Socket
If the BIOS needs to be changed, please contact the Vecow RMA service team.
CN1
2.4.6 SATA Connector
Standard 7 PIN SATA Connector
There are 4 onboard high performance Serial ATA III. It supports higher storage capacity with less cabling effort and smaller required space. SATA4 is only for
BOM option, default without function.
SATA3
SATA1
Pin No.
1
2
3
4
SATA4 SATA2
Definition
Ground
TX DP
TX DN
Ground
Pin No.
5
6
7
Definition
RX DN
RX DP
Ground
GETTING TO KNOW YOUR ECS-9700/ 9600
33
2.4.7 SATA Power Header
Standard, all form factor 1x4p power header
There are 2 HDD power header on board and each power header supports two
2.5” SATA HDD.
J3
J2
Pin No.
1
3
Description
+V5 (Max. 4A)
Ground
Pin No.
2
4
Description
Ground
+V12 (Max. 1.5A)
2.4.8 Internal USB2.0
Standard Vertical USB2.0 Connector.
ECS-9700 main board provides one expansion USB port using plug-and-play for dongle key or LCD touch panel. The USB interface supports 480 Mbps transfer rate complied with high speed USB specification Rev. 2.0.
The USB interface is accessed through one standard USB 2.0 connector. This
USB 2.0 does not support wake up function.
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
34
CN20
Pin No.
1
3
Definition
USB +VCC (+V5/Max. 0.5A)
DATA+
Pin No.
2
4
Definition
DATA-
Ground
2.4.9 SUMIT A, SUMIT B
This system has standard SUMIT A and SUMIT B for SUMIT type add on cards.
SUMITB
SUMITA
GETTING TO KNOW YOUR ECS-9700/ 9600
35
SUMIT A Pin Out:
37
39
41
43
29
31
33
35
45
47
49
51
21
23
25
27
13
15
17
19
Pin No.
1
3
9
11
5
7
USB_1+
USB_1-
+5V
USB_0+
USB_0-
GND
A_PET_P0
A_PET_N0
GND
PERST#
WAKE#
+5V
Function
+5V_AUX
+3.3V
+3.3V
Reserved
Reserved
USB_OC#
Reserved
+5V
USB_3+
USB_3-
+5V
USB_2+
USB_2-
+5V
38
40
42
44
30
32
34
36
46
48
50
52
22
24
26
28
14
16
18
20
Pin No.
2
4
10
12
6
8
Function
+12V
SMB_DATA
XMB_CLK
Reserved
SPI_MISO
SPI_MOSI
SPI_CLK
SPI_CS10
SPI_CS1#
Reserved
LPC_DRQ1#
LPC_AD0
LPC_AD1
LPC_AD2
LPC_AD3
LPC_FRAME#
SERIRQ#
Reserved
CLK_33MHz
GND
A_PER_P0
A_PER_N0
APRSNT#/A_PE_CLKREQ#
A_CLKP
A_CLKN
GND
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
36
SUMIT B Pin Out:
37
39
41
43
29
31
33
35
45
47
49
51
21
23
25
27
15
17
19
11
13
7
9
Pin No.
1
3
5
Function
GND
B_PET_P0
B_PET_N0
GND
C_CLKP
C_CLKN
CPRSNT#/C_PE_CLKREQ#
C_PET_P0
C_PET_N0
GND
C_PET_P1
C_PET_N1
GND
C_PET_P2
C_PET_N2
GND
C_PET_P3
C_PET_N3
GND
PERST#
Reserved
+5V
+5V
+5V
+5V
+5V
38
40
42
44
30
32
34
36
46
48
50
52
22
24
26
28
16
18
20
8
10
12
14
Pin No.
2
4
6
C_PER_N2
GND
C_PER_P3
C_PER_N3
GND
WAKE#
Reserved
Reserved
+3.3V
+3.3V
+3.3V
+5V_AUX
Function
GND
B_PER_P0
B_PER_N0
GND
B_CLKP
B_CLKN
GND
C_PER_P0
C_PER_N0
GND
C_PER_P1
C_PER_N1
GND
C_PER_P2
GETTING TO KNOW YOUR ECS-9700/ 9600
37
2.4.10 Mini PCIe/ mSATA Slot
CN10 CN8
SW2
CN6
CN12
No.
Conn.
SIM mSATA USB 2.0
Mini PCIe 1 CN12 SIM1 (CN13) SATA4
Mini PCIe 2 SIM2 (CN9)
Mini PCIe 3 CN10 SIM3 (CN11) SATA6
Mini PCIe 4
CN8
CN6 SIM4 (CN7)
SATA5
SATA7
V
V
V
-
Remark
Option with SATA4 HDD Connector
SIM Only support PCIe module
Mini PCIe and mSATA share the same form factor and similar electrical pinout assignments on their connectors. There is no clear mechanism to distinguish if a mSATA drive or a Mini PCIe device is plugged into the socket until recently that SATA I/O issued an ECN change (ECN #045) to redefine pin-43 on mSATA connector as “no connect” instead of “return current path” (or GND). When an mSATA drive is inserted, its pin-43 is “no connect”, and the respective pin on the socket is being pulled-up to logic 1. When a Mini PCIe device is inserted, its pin-
43 forces the respective pin on the socket to ground, or logic 0.
SW2 is for switching mSATA drive and Mini PCIe device.
DIP Switch
SW2-1
Mini PCIe 1
SW2-2
Mini PCIe 2
SW2-3
Mini PCIe 3
SW2-4
Mini PCIe 4
ON
OFF
ON
OFF
ON
OFF
ON
OFF
Interface
Mini PCIe
Auto Detection (Default)
Mini PCIe
Auto Detection (Default)
Mini PCIe
Auto Detection (Default)
Mini PCIe
Auto Detection (Default)
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
38
Pin Out:
31
29
27
25
37
35
33
23
21
19
17
45
43
41
39
Pin No.
51
49
47
5
3
9
7
1
15
13
11
GND
GND
PETp0
PETn0
GND
GND
PERn0 function
Reserved
Reserved
Reserved
Reserved
GND
+3.3Vaux
+3.3Vaux
PERp0
GND
Reserved
Reserved
GND
REFCLK+
REFCLK-
GND
CLKREQ#
Reserved
Reserved
WAKE#
Mechanical Key
16
14
12
24
22
20
18
6
4
10
8
2
32
30
28
26
38
36
34
46
44
42
40
Pin No.
52
50
48 function
+3.3Vaux
GND
+1.5V
Reserved
Reserved
Reserved
GND
USB_D+
USB_D-
GND
SMB_DATA
SMB_CLK
+1.5V
GND
+3.3Vaux
PERST# reserved
GND
UIM_VPP
UIM_RESET
UIM_CLK
UIM_DATA
UIM_PWR
1.5V
GND
3.3Vaux
GETTING TO KNOW YOUR ECS-9700/ 9600
39
2.4.11 RTC Battery
The system’s real-time clock is powered by a lithium battery. It is equipped with
Panasonic BR2032 190mAh lithium battery. It is recommended that you do not have to get the lithium battery on your own. If the battery needs to be changed, please contact the Vecow RMA service team.
BAT
2.4.12 FAN Header
Fan power connector supports for additional thermal requirements. The pin assignments of FAN 1 are shown in the following diagram:
FN1
Pin out:
Pin No.
1
3
Function
GND
Fan speed sensor
Pin No.
2
4
Function
+12V (1.5A max)
Fan PWM
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
40
2.4.13 LPC Port 80 Header
ECS-9700 provides a LPC Port 80 Header for debug card.
CN3
Pin out:
Pin No.
3
4
1
2
5
6
Function
SERIRQ
+3.3V
LA3
RESET#
LAD1
LAD2
2.4.14 LAN IEEE 1588 Header
ECS-9700 provides a LAN header for IEEE 1588.
LAN No.
Front LAN2
Rear POE LAN3
Rear POE LAN4
Rear POE LAN5
Rear POE LAN6
Function
Intel I210
Intel I210
Intel I210
Intel I210
Intel I210
Pin No.
7
8
9
10
11
12
Function
LFRAME#
LAD0
N/C
Ground
CLOCK
Ground
Function
J5
J6
J7
J8
J9
GETTING TO KNOW YOUR ECS-9700/ 9600
41
J9 J8 J7 J6
JP3
Pin out:
Pin No.
1
3
5
Function
SPD0
SPD2
Ground
Pin No.
2
4
6
Function
SPD1
SPD3
Ground
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
42
2.4.15 COM Port Header
ECS-9700 provides 4 COM port headers for internal COM port cable.
CN27 CN28
Pin out:
CN27:
Pin No.
5
6
3
4
1
2
9
10
7
8
Description
Ground_Frame
Ground
RI
DTR
CTS
TXD
RTS
RXD
DSR
DCD
Port
COM3
COM3
COM3
COM3
COM3
COM3
COM3
COM3
COM3
COM3
CN28:
Pin No.
5
6
3
4
1
2
9
10
7
8
Description
Ground_Frame
Ground
RI
DTR
CTS
TXD
RTS
RXD
DSR
DCD
Port
COM4
COM4
COM4
COM4
COM4
COM4
COM4
COM4
COM4
COM4
GETTING TO KNOW YOUR ECS-9700/ 9600
43
2.5 Main Board Jumper & Deep Switch Settings
2.5.1 Top View of ECS-9700 With Jumper and Deep Switch
CN36
CN20
CN10
JP5 JP6
JP9
SATA3
SATA4
SATA1
SATA2
J3
J2
JP2
J9
U3 U2
CN1
CN8
J8
FN1
J7
JP11 JP10
SW3 SW4
JP7
JP8
J6
SW7
CN27 CN28
J1
CN5
CN3
SW2
JP1
CN7
CN6
JP3
JP4
J5
CN2
J10
SW5
BZ1
CN12
BAT
CFast
SW11
CN9
J11
SUMITB
SUMITA
The figure below is the top view of ECS-9700 board, and it shows the location of the jumpers and the switches.
You may configure your card to match the needs of your application by setting jumpers. A jumper is a metal bridge used to close an electric circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper, please connect the pins with the clip. To “open” a jumper, please remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3. In this case you would connect either pins 1 and 2, or 2 and 3.
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
44
You may configure your card to match the needs of your application by DIP switch as shown below (the deep switch on and off)
ON ON ON
1 : OFF
2 : OFF
1 : ON
2 : OFF
1 : ON
2 : ON
1 2 1 2 1 2
2.5.2 USB Power Jumper
JP2
JP3 JP4
Jumper Setting
JP3
JP3
JP4
JP4
JP2
JP2
1:2
2:3
1:2
2:3
1:2
2:3
Function
Non Wake Up support
Supported Wake Up (Default)
Non Wake Up support
Supported Wake Up (Default)
Non Wake Up support
Supported Wake Up (Default)
USB Port
As front plane, blue mark
As front plane, blue mark
As front plane, red mark
As front plane, red mark
As rear plane, green mark
As rear plane, green mark
GETTING TO KNOW YOUR ECS-9700/ 9600
45
2.5.3 COM Port RI pin Select
JP5 JP6
JP7
JP8
Pin Header
COM1
JP5
Pin Header
COM2
JP6
Pin Header
COM3
JP7
Pin Header
COM4
JP8
Pin No.
1-2
3-4
5-6
Pin No.
1-2
3-4
5-6
Pin No.
1-2
3-4
5-6
Pin No.
1-2
3-4
5-6
©Vecow ECS-9700/ 9600 User Manual
Description
+5V (1A max.)
+12V (0.5A max.)
RI (Default)
Description
+5V (1A max.)
+12V (0.5A max.)
RI (Default)
Description
+5V (1A max.)
+12V (0.5A max.)
RI (Default)
Description
+5V (1A max.)
+12V (0.5A max.)
RI (Default)
GETTING TO KNOW YOUR ECS-9700/ 9600
46
2.5.4 COM Port RS-422/RS-485 Receiver Terminator
SW3 SW4
COM / DIP Switch
COM1 / SW3-1
COM / DIP Switch
COM2 / SW3-2
COM / DIP Switch
COM3 / SW4-1
COM / DIP Switch
COM4 / SW4-2
ON / OFF
ON
OFF
ON / OFF
ON
OFF
ON / OFF
ON
OFF
ON / OFF
ON
OFF
COM RS-422/485
Receiver Terminator
*Enable
Disable
COM RS-422/485
Receiver Terminator
*Enable
Disable
COM RS-422/485
Receiver Terminator
*Enable
Disable
COM RS-422/485
Receiver Terminator
*Enable
Disable
GETTING TO KNOW YOUR ECS-9700/ 9600
47
2.5.5 POE Power ON Select
JP9
Jumper
JP9
JP9
Setting
1:2
2:3
2.5.6 CMOS & ME Clear
Function
POE power on at standby power ready
POE power on after system power on (Default)
SW11
Function
CMOS Clear Setting
Function
ME Clear Setting
©Vecow ECS-9700/ 9600 User Manual
DIP Switch
SW 1-1
ON
OFF
DIP Switch
SW 1-2
ON
OFF
Description
Clear CMOS
*Normal
Description
Clear ME
*Normal
GETTING TO KNOW YOUR ECS-9700/ 9600
48
2.6 Ignition Control
ECS-9700 series provides ignition power control feature for in-vehicle applications. The built-in MCU monitors the ignition signal and turns on/off the system according to pre-defined on/off delay periods.
2.6.1 Adjust Ignition Control Modes
ECS-9700 series provides 16 modes of different power on/ off delay periods adjustable via SW5 switch. The default rotary switch is set to 0 in ATX/ AT power mode.
SW5
GETTING TO KNOW YOUR ECS-9700/ 9600
49
The modes are listed in the following table:
Item Power on delay Power off delay
0 ATX mode
5 seconds
10 seconds
10 seconds
10 seconds
10 seconds
10 seconds
10 seconds
No delay
No delay
No delay
No delay
5 seconds
5 seconds
5 seconds
5 seconds
B
C
9
A
D
E
F
6
7
4
5
8
1
2
3
1 hour
2 hours
4 hours
6 hours
8 hours
12 hours
24 hours
No delay
5 seconds
10 seconds
20 seconds
30 seconds
60 seconds
90 seconds
30 minutes
ON
1
ON
1
ON
1
ON
1
ON
1
ON
1
ON
1
ON
1
ON
1
ON
1
ON
1
ON
1
ON
1
1
ON
1
ON
1
Switch Position
ON
2 3 4
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
©Vecow ECS-9700/ 9600 User Manual
GETTING TO KNOW YOUR ECS-9700/ 9600
50
2.6.2 Ignition Control Wiring
To activate ignition control, you need to provide IGN signal via the 3-pin pluggable terminal block located in the back panel. It is below the general wiring configuration.
V+
IGN
Pin No.
1
2
3
Definition
Ignition (IGN)
External Power S/W +
External Power S/W +
For testing purpose, you can refer to the picture above to simulate ignition signal input controlled by a latching switch.
Note:
1. DC power source and IGN share the same ground.
2. ECS-9700/9600 supports 6V~36V wide range DC power input in ATX/AT mode. In Ignition mode, the input voltage is fixed to 12V/24V for car battery scenario.
3. For proper ignition control, the power button setting should be “Power down” mode.
In Windows, for example, you need to set “When I press the power button” to
"Shut down."
GETTING TO KNOW YOUR ECS-9700/ 9600
51
3
SYSTEM SETUP
3.1 How to Open Your ECS-9700/9600
Step 1 Remove hole plugs.
Step 2 Remove two F#6-32 screws (circled in red) and two F-M3 screws
(circled in yellow) on the bottom side.
©Vecow ECS-9700/ 9600 User Manual
HARDWARE INSTALLATION
52
Step 3 Finish Step1 and 2.
Step 4 Remove one KHS#6-32x6 screws(red) and cover(yellow).
HARDWARE INSTALLATION
53
Step 5 Open the module.
Step 6 Finish.
©Vecow ECS-9700/ 9600 User Manual
HARDWARE INSTALLATION
54
3.2 Installing DDR4 SO-DIMM Modules
Step 1 DDR4 RAM module into SO-DIMM slot.
Step 2 Make sure the RAM module is locked by the memory slot.
HARDWARE INSTALLATION
55
3.3 Installing Mini PCIe Card
Step 1 Install Mini PCIe card into the Mini PCIe socket.
Step 2 Fasten one M2.5 screw.
©Vecow ECS-9700/ 9600 User Manual
HARDWARE INSTALLATION
56
3.4 Installing CFast Card
Step 1 Remove 2 pcs F-M3x4 screws on CFast & SIM Card.
Step 2 Before Inserting CFast & SIM Card, make sure ECS-9700 power is not plugged.
Step 3 Insert CFast card and push to lock.
Step 4 Insert CF card and push to lock.
HARDWARE INSTALLATION
57
3.5 Installing SIM Card
Step 1 Remove 2 pcs F-M3x4 screws on CFast & SIM Card.
Step 2 Before Inserting CFast & SIM Card, make sure ECS-9700 power is not plugged.
Step 3 Insert CFast card and push to lock.
Step 4 Insert SIM card and push to lock.
©Vecow ECS-9700/ 9600 User Manual
HARDWARE INSTALLATION
58
3.6 Installing PCI/ PCIe Card
Step 1 Remove the M3 screw.
Step 2 Remove the bracket.
HARDWARE INSTALLATION
59
Step 3 Installing PCI/PCIe card.
Step 4 Fasten M3 screw.
©Vecow ECS-9700/ 9600 User Manual
HARDWARE INSTALLATION
60
3.7 Installing SSD/ HDD
Step 1 Trigger and open SSD/HDD tray.
Step 2 Insert 2.5” SSD/HDD in the tray and fasten two F-M3x4 screws.
HARDWARE INSTALLATION
61
Step 3 Finish.
Step 4 Installing SSD/HDD.
©Vecow ECS-9700/ 9600 User Manual
HARDWARE INSTALLATION
62
3.8 Mounting Your ECS-9700/9600
3.8.1 Wall Mount Bracket
Step 1 Ensure the screw holes on the right and left side of the upper
case match the ones on ECS-9700/9600 wall mount bracket.
HARDWARE INSTALLATION
63
Step 2 Fasten 4pcs KHS#6-32 screws then finish.
©Vecow ECS-9700/ 9600 User Manual
HARDWARE INSTALLATION
64
3.8.2 VESA Mount
Step 1 ECS-9700/9600 and VESA Mount.
Step 2 Take ECS-9700/9600 and VESA Mount with fasten 4pcs
KHS#6-32 screws.
HARDWARE INSTALLATION
65
Step 3 Fasten four KHS#6-32 screws and then finish.
Step 4 Finish.
Step 5 VESA size have 75x75mm(red) and 100x100mm(yellow).
©Vecow ECS-9700/ 9600 User Manual
HARDWARE INSTALLATION
66
3.8.3 Din Rail Kit
Step 1 ECS-9700/9600 and Din Rail Kit.
Step 2 Take ECS-9700/9600 and Din Rail Kit and fasten four KHS#6-32 screws in the four marked corners.
HARDWARE INSTALLATION
67
Step 3 Fasten four KHS#6-32 screws and then finish.
Step 4 Finish.
Step 5 ECS-9700/9600 With Din Rail.
©Vecow ECS-9700/ 9600 User Manual
HARDWARE INSTALLATION
68
4
BIOS SETUP
4.1 Entering BIOS SETUP
Figure 4-1: Entering Setup Screen
BIOS provides an interface for users to check and change system configuration.
The BIOS setup program is accessed by pressing the <Del> key when POST display output is shown.
BIOS AND DRIVER SETTING
69
4.2 Main
Figure 4-2: BIOS Main Menu
The main menu displays BIOS version and system information. There are two options on Main menu.
System Date
Set the date. Use <Tab> to switch between date elements.
System Time
Set the time. Use <Tab> to switch between time elements.
4.3 Advanced
Figure 4 3: BIOS Advanced Menu
Select advanced tab to enter advanced BIOS setup options, such as CPU configuration, SATA configuration, and USB configuration.
©Vecow ECS-9700/ 9600 User Manual
BIOS AND DRIVER SETTING
70
4.3.1 Trusted Computing
Figure 4 3-1: Trusted Computing
Control the TPM device status and display related information if TPM chip is present.
4.3.2 ACPI Settings
Figure 4 3-2: ACPI Settings
Enable Hibernation
Enables or disables system's ability to hibernate (OS/S4 sleep state). This option may not be effective with some OS.
ACPI Sleep State
Selects the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.
S3 Video Repost
Enables or disables S3 video repost.
ACPI Low Power S0 Idle
Enables or disables ACPI low power S0 idle support.
BIOS AND DRIVER SETTING
71
4.3.3 AMT Configuration
Figure 4 3-3: Intel AMT Settings
Intel AMT
Enables/disables Intel (R) Active Management Technology BIOS extension.
Note: iAMT H/W is always enabled. This option just controls the BIOS extension execution. If enabled, this requires additional firmware in the SPI device.
4.3.4 PCH-FW Configuration
Figure 4 3-4: PCH-FW Settings
ME Unconfig on RTC Clear State
Disabling this option will cause ME not to unconfigure on RTC clear.
ME State
Set ME to Soft temporarily disabled.
4.3.5 SMART Settings
Figure 4 3-5: SMART Settings
SMART Self Test
Run SMART self test on all HDDs during POST.
©Vecow ECS-9700/ 9600 User Manual
BIOS AND DRIVER SETTING
72
4.3.6 IT8786 Super IO Configuration
Figure 4-3-6-1: Super IO Settings
Figure 4-3-6-2: Serial Port Settings
Serial Port 1 to port 4 Configuration
Options for Serial Port 1 to Serial Port 4.
Entering the corresponding Port option then end user can change the settings such as I/O resource and UART mode.
Figure 4 3-6-3: GPIO Pin Input/Output Settings of SIO IT8786
Set the direction of the GPIO pins
Creates bios options for end user to change internal GPIO pin direction.
BIOS AND DRIVER SETTING
73
4.3.7 Hardware Monitor
Figure 4 3-7: Hardware Monitor Settings
The IT8786 SIO features an enhanced hardware monitor providing thermal, fan speed, and system voltages' status monitoring.
4.3.8 Serial Port Console Redirection
Figure 4 3-8: Serial Port Console Redirection Settings
Console Redirection
Console redirection enable or disable.
Console Redirection Settings
These settings specify how the host computer and the remote computer (which the user is using) will exchange data. Both computers should have the same or compatible settings.
©Vecow ECS-9700/ 9600 User Manual
BIOS AND DRIVER SETTING
74
4.3.9 CPU Configuration
Figure 4 3-9: CPU Function Settings
Hyper-threading
Enabled for Windows XP and Linux (OS optimized for Hyper-Threading
Technology) and disabled for other OS (OS not optimized for Hyper-Threading
Technology). When disabled only one thread per core is enabled.
Active Processor Cores
Number of cores to enable in each processor package.
Intel Virtualization Technology
When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology.
Hardware Prefetcher
To turn on/off the MLC streamer prefetcher.
Adjacent Cache Line Prefetch
To turn on/off prefetching of adjacent cache lines.
CPU AES
Enable/disable CPU Advanced Encryption Standard instructions.
Boot performance mode
Select the performance state that the BIOS will set before OS handoff.
Intel(R) SpeedStep(tm)
Allows more than two frequency ranges to be supported.
Turbo Mode
Turbo Mode.
BIOS AND DRIVER SETTING
75
CPU C state
Enable or disable CPU C states.
Enhanced C-states
Enable/disable C1E. When enabled, CPU will switch to minimum speed when all cores enter C-State.
Package C State limit
Package C State limit.
Intel TXT(LT) Support
Enables or disables Intel (R) TXT (LT) support.
4.3.10 Intel TXT Information
Figure 4 3-10: Intel TXT Information
Display Intel TXT information.
4.3.11 SATA Configuration
©Vecow ECS-9700/ 9600 User Manual
Figure 4 3-11: SATA Devices Settings
BIOS AND DRIVER SETTING
76
SATA Controller(s)
Enable or disable SATA Device.
SATA Mode Selection
Determines how SATA controller(s) operate.
Software Feature Mask Configuration
RAID OROM/RST driver will refer to the SWFM configuration to enable or disable the storage features.
Aggressive LPM Support
Enable PCH to aggressively enter link power state.
SATA Controller Speed
Indicates the maximum speed the SATA controller can support.
Options for each SATA port:
Port 0
Enable or disable SATA Port.
Spin Up Device
On an edge detect from 0 to 1, the PCH starts a COMRESET initialization sequence to the device.
SATA Device Type
Identifies that the SATA port is connected to solid state drive or hard disk drive.
4.3.12 Acoustic Management Configuration
Figure 4 3-12: Acoustic Management Settings
Acoustic Management Configuration
Option to enable or disable automatic acoustic management.
BIOS AND DRIVER SETTING
77
4.3.13 CSM Configuration
CSM Support
Enable/disable CSM support
Figure 4 3-13: CSM Settings
GateA20 Active
UPON REQUEST - GA20 can be disabled using BIOS services.
ALWAYS - do not allow GA20 to be disabled; this option is useful when any RT code is executed above 1MB.
Option ROM Messages
Set display mode for Option ROM.
INT19 Trap Response
BIOS reaction on INT19 trapping by Option ROM:
IMMEDIATE - execute the trap right away;
POSTPONED - execute the trap during legacy boot.
Boot option filter
This option controls Legacy/UEFI ROM's priority.
Network
Controls the execution of UEFI and Legacy PXE OpROM.
Storage
Controls the execution of UEFI and Legacy Storage OpROM.
Video
Allows more than two frequency ranges to be supported.
Other PCI devices
Determines OpROM execution policy for devices other than network, storage, or video.
©Vecow ECS-9700/ 9600 User Manual
BIOS AND DRIVER SETTING
78
4.3.14 USB Configuration
Figure 4 3-14: USB Settings
Legacy USB Support
Enables Legacy USB support.
AUTO option disables Legacy support if no USB devices are connected.
DISABLE option will keep USB devices available only for EFI applications.
XHCI Hand-off
This is a workaround for OS-es without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver.
USB Mass Storage Driver Support
Enable/disable USB mass storage driver support.
Port 60/64 Emulation
Enables I/O port 60h/64h emulation support. This should be enabled for the complete USB keyboard legacy support for non-USB aware OS-es.
USB transfer time-out
The time-out value for control, bulk, and interrupt transfers.
Device reset time-out
USB mass storage device start unit command time-out.
Device power-up delay
Maximum time the device will take before it properly reports itself to the Host
Controller. 'Auto' uses default value, for a root port it is 100 ms, for a hub port the delay is taken from the hub descriptor.
BIOS AND DRIVER SETTING
79
4.4 Chipset
Figure 4-4: BIOS Chipset Menu
System Agent (SA) Configuration
System Agent (SA) parameters.
PCH-IO Configuration
PCH parameters.
4.4.1 System Agent (SA) Configuration
Figure 4-4-1: System Agent Settings
VT-d
VT-d capability.
GMM Device (B0:D8:F0)
Enable/disable SA GMM device.
Above 4GB MMIO BIOS assignment
Enable/disable above 4GB MemoryMappedIO BIOS assignment. This is disabled automatically when aperture size is set to 2048MB.
©Vecow ECS-9700/ 9600 User Manual
BIOS AND DRIVER SETTING
80
4.4.2 Graphics Configuration of System Agent (SA)
Figure 4-4-2: Graphics Settings
Graphics Turbo IMON Current
Graphics turbo IMON current values supported (14-31).
Skip Scaning of External Gfx Card
If Enable, it will not scan for External Gfx Card on PEG and PCH PCIE Ports.
Primary Display
Select which of IGFX/PEG/PCI Graphics device should be Primary Display Or select SG for Switchable Gfx.
GTT Size
Select the GTT Size.
Aperture Size
Select the Aperture Size.
Note: Above 4GB MMIO BIOS assignment is automatically enabled when selecting 2048MB aperture. To use this feature, please disable CSM Support.
DVMT Pre-Allocated
Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the
Internal Graphics Device.
DVMT Total Gfx Mem
Select DVMT5.0 Total Graphic Memory size used by the Internal Graphics
Device.
Cd Clock Frequency
Select the highest Cd Clock frequency supported by the platform.
BIOS AND DRIVER SETTING
81
4.4.3 PEG Port Configuration (SA)
Figure 4-4-3: PEG Port Configuration
PEG port options for PCIe device.
4.4.4 Memory Information of System Agent (SA)
Figure 4-4-4: Memory Information
Displays memory information.
4.4.5 PCH-IO Configuration
©Vecow ECS-9700/ 9600 User Manual
Figure 4-4-5: PCH-IO Settings
BIOS AND DRIVER SETTING
82
PCH LAN Controller
Enable or disable onboard NIC.
Wake on LAN
Enable or disable integrated LAN to wake the system. (The wake On LAN cannot be disabled if ME is on at Sx state.)
Serial IRQ Mode
Configure serial IRQ mode.
State After G3
Specify what state to go to when power is re-applied after a power failure (G3 state).
S0 State: Always turn-on the system when power source plugged-in.
S5 State: Always turn-off the system when power source plugged-in.
4.4.6 PCI Express Configuration of PCH-IO
Figure 4-4-6: PCH-IO Settings
DMI Link ASPM Control
Enable/Disable the control of Active State Power Management on SA side of the
DMI Link.
SUMIT B x 1
Enable or disable PCIe device on SUMIT B.
Front-I210-LAN2
Enable or disable I210 LAN.
Rear-I210-LAN3 to LAN6
Enable or disable I210 LAN.
SUMIT A x 1
Bios options for PCIe device on SUMIT A.
Mini PCIe Slot 1 to 4
Bios options for PCIe devices on miniPCIe Slot.
BIOS AND DRIVER SETTING
83
4.4.7 BIOS Security Configuration of PCH-IO
Figure 4-4-7: BIOS Security Settings
BIOS Lock
Enable/disable the PCH BIOS Lock Enable (BLE bit) feature.
4.4.8 SB Porting Configuration of PCH-IO
Figure 4-4-8: RAID ROM Settings
SATA RAID ROM
Legacy ROM: Legacy option ROM
UEFI Driver: UEFI Raid Driver
Both: Run the Legacy Option ROM and UEFI driver.
©Vecow ECS-9700/ 9600 User Manual
BIOS AND DRIVER SETTING
84
4.5 Security
Administrator Password
Set administrator password.
Figure 4-5: BIOS Security Menu
User Password
Set user password.
4.5.1 HDD Security Configuration
Figure 4-5-1: HDD Security Settings
Set User Password
Set HDD user password.
*** Advisable to power cycle system after setting hard disk passwords ***
Discard or save changes option in setup does not have any impact on HDD when password is set or removed. If the 'Set HDD User Password' option is gray, do power cycle to enable the option again.
BIOS AND DRIVER SETTING
85
4.6 Boot
Figure 4-6: BIOS Boot Menu
Setup Prompt Timeout
Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting.
Bootup NumLock State
Select the keyboard NumLock state.
Quiet Boot
Enables or disables Quiet Boot option.
Boot Option
Sets the system boot order.
New Boot Option Policy
Controls the placement of newly detected UEFI boot options.
Hard Drive BBS Priorities
Set the order of the Legacy devices in this group.
©Vecow ECS-9700/ 9600 User Manual
BIOS AND DRIVER SETTING
86
4.7 Save & Exit
Figure 4-7: Bios Save and Exit Menu
Save Changes and Exit
Exit system setup after saving the changes.
Discard Changes and Exit
Exit system setup without saving any changes.
Save Changes and Reset
Reset the system after saving the changes.
Discard Changes and Reset
Reset system setup without saving any changes.
Save Changes
Save changes done so far to any of the setup options.
Discard Changes
Discard changes done so far to any of the setup options.
Default Options:
Restore Defaults
Restore/load default values for all the setup options.
Save as User Defaults
Save the changes done so far as user defaults.
Restore User Defaults
Restore the user defaults to all the setup options.
BIOS AND DRIVER SETTING
87
A
APPENDIX A : Isolated DIO Guide
A.1 I/O Pin Definition
GPIO Pin
10, 13, 14, 17
11, 12, 15, 16
20 ~ 27
30, 31, 34
32, 33, 35 ~ 37
40 ~ 47
50 ~ 52, 56, 57
53, 54
60 ~ 63, 66, 67
64, 65
70 ~ 77
80 ~ 87
Base Address
0xA00
0xA01
0xA02
0xA03
0xA04
0xA05
0xA06
0xA07
Usage
-----------
CN16-GPIO
-----------
-----------
CN16-GPIO
-----------
CN16-GPIO
-----------
-----------
CN16-GPIO
DO
DI
Appendix A
88 ©Vecow ECS-9700/ 9600 User Manual
A.2 Function Description
The ECS-9700 offers two 16-bit DIO (8-DI/ 8-DO) 20-pin terminal block connector. Each bit of DI and DO equipped with a photo-coupler for isolated protection. All IO pins are fixed by Hardware design and cannot change in/out direction in runtime process. The definition is listed as follows:
Definition
EXT_IN0
EXT_IN1
EXT_IN2
EXT_IN3
EXT_IN4
EXT_IN5
EXT_IN6
EXT_IN7
DI_COM
EGND
6
7
4
5
2
3
Pin
No.
1
8
9
10
Description
DI4
DI5
DI6
DI7
DI0
DI1
DI2
DI3
DI COM
DIO GND
18
19
20
16
17
14
15
Pin
No.
11
Definition
EXT_OUT0
12
13
EXT_OUT1
EXT_OUT2
EXT_OUT3
EXT_OUT4
EXT_OUT5
EXT_OUT6
EXT_OUT7
Reserved
E24V
Description
DO4
DO5
DO6
DO7
DO0
DO1
DO2
DO3
NC
External 24V DC
Appendix A
89
A.3 DIO Signal Circuit
DI reference circuit:
Sink Mode (NPN)
6-48V DC
V+
V-
Source Mode (PNP)
Power
Supply
6-48V DC
V+
V-
DIO Connector
DI_COM (Pin 9)
DI (Pin1-8)
DIO Connector
DI_COM (Pin 9)
DI (Pin1-8)
DO reference circuit:
Sink Mode
(NPN, Default)
Device
6-48V DC
V+
IO
V-
Source Mode
(PNP)
Device
6-48V DC
V+
IO
V-
DIO Connector
DIO_VDC (Pin 20)
DO (Pin11-18)
DIO_GND (Pin10,19)
DIO Connector
DIO_VDC (Pin 20)
DO (Pin11-18)
DIO_GND (Pin10,19)
©Vecow ECS-9700/ 9600 User Manual
Appendix A
90
A.4 Software Package contain
There are two folders with the following inside:
● Driver folder includes x32 & x64 versions
● Runtime folder includes DLL and header file for software developer
or system integration
● Sample folder includes sample program
A.5 Driver Install
In Driver folder, you can find the files below inside.
Please right click the batch file that is chosen by your OS version, and run as administrator.
Please press any key to install the Framework installation.
Appendix A
91
Please press any key to restart.
On Device Manager, “VECOW Embedded IO Access” will be added.
©Vecow ECS-9700/ 9600 User Manual
Appendix A
92
A.6 DIO Demo Tool
Execute DIO demo tool (ECS9K7.exe).
Operation on DIO demo tool utility.
Operation on DIO / WDT / PoE Demo tool utility.
Click “Read” Button to get value; Input any number in Write and Write Mask textbox, and click “Write” Button to set value.
On DIO Panel, Check the DO circuit for “NPN” / “PNP” mode.
On PoE Panel, Click “R” to disable PoE switch function (to auto disconnect mode); Click “W” to enable PoE switch function (to manual setting mode).
Appendix A
93
B
APPENDIX B : Software Functions
B.1 IOMem.Dll API
Kernel access for GPIO, WDT & POE.
int Outp(unsigned long Port, unsigned char Value);
Description: Set Byte-Data to Port.
Return: if success return 1; else return 0.
unsigned char Inp(unsigned int Port);
Description: Get Byte-Data from Port.
int Outpd(unsigned int Port, unsigned long Value);
Description: Set DWORD-Data to Port.
Return: if success return 1; else return 0.
unsigned long Inpd(unsigned int Port);
Description: Get DWORD-Data from Port.
B.2 Entry Functions
Functions for GPIO, WDT & POE.
int Get_DI1(unsigned char *DI);
Description: Get DI Data for DIO1.
Return: if success return 1; else return 0.
int Set_DO1(unsigned char DO);
Description: Set DO Data for DIO1.
Return: if success return 1; else return 0.
int Get_DI2(unsigned char *DI);
Description: Get DI Data for DIO2.
Return: if success return 1; else return 0.
int Set_DO2(unsigned char DO);
Description: Set DO Data for DIO2.
Appendix B
94 ©Vecow ECS-9700/ 9600 User Manual
Return: if success return 1; else return 0.
int Set_WDT(unsigned long time);
Description: Set WDT Time for WDT.
Return: if success return 1; else return 0.
int Get_POE(unsigned short *POEI, unsigned short *Func);
Description: Get POE Data.
Return: if success return 1; else return 0.
Mask [bit]=0 for disable; [bit]=1 for enable
int Set_POE(unsigned short POEO, unsigned short Func);
Description: Set POE Data.
Return: if success return 1; else return 0.
Mask [bit]=0 for disable; [bit]=1 for enable
Appendix B
95
C
APPENDIX C : RAID Installation Guide
C.1 SATA Mode for RAID
Please select SATA device to RAID mode on BIOS menu.
Advanced → SATA Configuration → SATA Mode Selection
C.2 OS Installation
ECS-9700/9600 is featured with eight SATA, option 1: include four internal
SATA, three mSATA and one CFast. Option 2: include three internal SATA, four mSATA and one CFast.
You can select one of SATA ports for OS installation
We used CFast card for Windows 10 OS installation as an example.
C.3 Install All Device Drivers of ECS-9700/9600 System
The instructions are as follows:
1. Install Chipset driver
2. Install Network driver
3. Install ME driver (if available)
4. Install Audio driver
5. Install VGA driver
©Vecow ECS-9700/ 9600 User Manual
Appendix C
96
C.4 Install “Intel Rapid Storage Technology” Software
You can get the software on ECS-9700 driver CD.
Also, you can find latest information and software directly from Intel website.
http://www.intel.com/p/en_US/support/highlights/chpsts/imsm
The RAID environment has been done if you completed the steps above.
C.5 Insert SATA HDD for RAID 1
Please notice, you can use six SATA ports for SATA HDD, except for the CFast port and mSATA slot.
C.6 Create RAID Volume on “Rapid Storage
Technology” Software
ECS-9700/9600 is featured with four SATA HDDs for RAID volume, so there are three options for choose on this page. Let’s take RAID 1 as example, please select ”RAID 1”.
Appendix C
97
C.7 Disk Management : Partition the Disk
After RAID 1 volume created, you can see the figure of SATA device allocation.
You will find “Volume_0000” in
SATA device at BIOS menu.
To start Disk Management tool, select "initialize disk."
Then add “Logical Device” for Windows access.
C.8 If One SATA HDD on RAID Volume is Out-of-use
After RAID 1 volume created, you can see the figure of SATA device allocation.
HDD CAUTION Sign
©Vecow ECS-9700/ 9600 User Manual
Appendix C
98
C.9 Recovery and Auto Re-build When Use the SAME
RAID HDD
C.10 Recovery and Auto Re-build When Use DIFFERENT
RAID HDD
There is a warning will pop-up to ask you if the disk is not a member of original
RAID volume.
If you press “Rebuild”, it will replace the broken SATA HDD to the last one SATA
HDD of RAID volume.
Appendix C
99
D
APPENDIX D : Power Consumption
Testing Board
RAM
USB-1
USB-2
USB-3
USB-4
CFAST
SATA 0
SATA 1
LAN 1 (i219)
LAN 2 (i210)
Graphics Output
Power Plan
Power Source
ECS-9700
16GB X 2
USB Keyboard Logitech K120
USB Mouse Microsoft 1113
USB Flash Transecnd 3.0 8GB
USB Flash Transecnd 3.0 8GB
Transcend Cfast CFX600 64GB
Transcedn SATA-3 SSD420 256GB
Seagate HDD 160GB
1.0 Gbps
1.0 Gbps
DP
Balance(Windows7 Power plan)
Chroma 62006P-100-25
©Vecow ECS-9700/ 9600 User Manual
Appendix D
100
D.1 Intel® Xeon® E3-1505M v5 (8M Cache, 2.80 GHz)
Power on and boot to Win 7 64-bit
CPU
Xeon
®
E3-
1505M v5
Xeon
®
E3-
1505M v5
Xeon
®
E3-
1505M v5
Xeon
®
E3-
1505M v5
Xeon
®
E3-
1505M v5
Power
Input
Standby Mode
Max
Current
Max
Consumption
06V 0.650A
03.90W
09V
12V
24V
36V
0.410A
0.310A
0.240A
0.230A
03.69W
03.72W
05.76W
08.28W
Sleep Mode
Max
Current
Max
Consumption
0.770A
04.62W
Idle Status :
CPU usage less 3%
Max
Current
Max
Consumption
3.800A
22.80W
0.500A
0.380A
0.280A
0.250A
04.50W
04.56W
06.72W
09.00W
2.540A
1.690A
1.040A
0.750A
22.86W
20.28W
24.96W
27.00W
CPU
Power
Input
Xeon
®
E3-
1505M v5
Xeon
®
E3-
1505M v5
Xeon
®
E3-
1505M v5
Xeon
®
E3-
1505M v5
Xeon
®
E3-
1505M v5
06V
09V
12V
24V
36V
Run 100% CPU usage without 3D
Max
Current
Max
Consumption
8.040A
48.24W
5.100A
3.780A
1.970A
1.380A
45.90W
45.36W
47.28W
49.68W
Run 100% CPU usage with 3D
Max
Current
Max
Consumption
8.390A
50.34W
5.520A
4.100A
2.060A
1.460A
49.68W
49.20W
49.44W
52.56W
Appendix D
101
D.2 Intel® Core™ i7-6820EQ (8M Cache, 2.80 GHz)
Power on and boot to Win 7 64-bit
CPU
Power
Input
Standby Mode
Max
Current
Max
Consumption
06V 0.640A
03.84W
Sleep Mode
Max
Current
Max
Consumption
0.790A
04.74W
Idle Status :
CPU usage less 3%
Max
Current
Max
Consumption
4.230A
25.38W
Core™ i7-
6820EQ
Core™ i7-
6820EQ
Core™ i7-
6820EQ
Core™ i7-
6820EQ
Core™ i7-
6820EQ
09V 0.400A
12V 0.310A
24V 0.240A
36V 0.220A
03.60W
03.72W
05.76W
07.92W
0.500A
0.390A
0.280A
0.250A
04.50W
04.68W
06.72W
09.00W
2.350A
1.780A
0.950A
0.690A
21.15W
21.36W
22.80W
24.84W
CPU
Power
Input
Core™ i7-
6820EQ
Core™ i7-
6820EQ
Core™ i7-
6820EQ
Core™ i7-
6820EQ
Core™ i7-
6820EQ
06V
09V
12V
24V
36V
Run 100% CPU usage without 3D
Max
Current
Max
Consumption
7.700A
46.20W
5.020A
3.760A
1.930A
1.340A
45.18W
45.12W
46.32W
48.24W
Run 100% CPU usage with 3D
Max
Current
Max
Consumption
8.250A
49.50W
5.660A
4.050A
2.180A
1.540A
50.94W
48.60W
52.32W
55.44W
©Vecow ECS-9700/ 9600 User Manual
Appendix D
102
D.3 Intel® Core™ i5-6440EQ (6M Cache, 2.70 GHz)
Power on and boot to Win 7 64-bit
CPU
Power
Input
Standby Mode
Max
Current
Max
Consumption
06V 0.630A
03.78W
Sleep Mode
Max
Current
Max
Consumption
0.800A
04.80W
Idle Status :
CPU usage less 3%
Max
Current
Max
Consumption
3.730A
22.38W
Core™ i5-
6440EQ
Core™ i5-
6440EQ
Core™ i5-
6440EQ
Core™ i5-
6440EQ
Core™ i5-
6440EQ
09V 0.400A
12V 0.310A
24V 0.230A
36V 0.210A
03.60W
03.72W
05.52W
07.56W
0.500A
0.400A
0.280A
0.240A
04.50W
04.80W
06.72W
08.64W
2.410A
1.860A
1.160A
0.830A
21.69W
22.32W
27.84W
29.88W
CPU
Power
Input
Core™ i5-
6440EQ
Core™ i5-
6440EQ
Core™ i5-
6440EQ
Core™ i5-
6440EQ
Core™ i5-
6440EQ
06V
09V
12V
24V
36V
Run 100% CPU usage without 3D
Max
Current
Max
Consumption
6.500A
39.00W
4.240A
3.350A
1.580A
1.100A
38.16W
40.20W
37.92W
39.60W
Run 100% CPU usage with 3D
Max
Current
Max
Consumption
8.240A
49.44W
5.070A
3.900A
2.140A
1.430A
45.63W
46.80W
51.36W
51.48W
Appendix D
103
E
APPENDIX E : Supported Memory &
Storage List
E.1 Supported Memory List
Testing Board
Memory Test
BurnInTest
ECS-9700/9600 version: 5.1
V8.1
E.2 Test Item
Channel
*2
*1(Socket 1)
*1(Socket 2)
Memtest
PASS
PASS
PASS
Bunin
PASS
PASS
PASS
Flash BIOS
PASS
N/A
N/A
Remove
Battery
PASS
PASS
PASS
©Vecow ECS-9700/ 9600 User Manual
Appendix E
104
E.3 NON-ECC
Brand
Transcend 8GB
Transcend 16GB
Info
8G 2Rx8 DDR4
2400 SO
16G 2Rx8 DDR4
2133 SO
NOTE & S\N
TS9CBSESE0000
C96645-0001
C96645-0002
TS0CASGSB0000
D20478-0004
D20478-0004
DSL DDR4 2133
4GB CL15
D4SS12081
SH21A-A
1614-35909
1614-35910
4GB innodisk
DDR4 SODIMM
M4S0-4GSSNCRG M0S11601080040001
M0S11601080040002
8GB innodisk
DDR4 2133 W/T
SODIMM
M4S0-8GSSO5RG
M0S21606010020001
M0S21606010020002
16GB innodisk
DDR4 2133 W/T
SODIMM
M4S0-AGS1O5RG
M0S11608040020001
M0S11608040020002
Kingston 16GB
2Rx8 2Gx64-Bit
PC4-2133
KVR21S15D8/16 BKMM1641607
BKMM1661618
Test Temp.
(Celsius)
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
Appendix E
105
E.4 ECC
Brand Info NOTE & S\N
Transcend 16GB
ECC Wild Temp.
Transcend 16GB
ECC
Transcend 4GB
ECC
DSL DDR4 2133
4GB CL15 ECC
DSL DDR4 2133
8GB CL15 ECC
DSL DDR4 2133
16GB CL15 ECC
4GB innodisk
DDR4 2133 ECC
8GB innodisk
DDR4 2133 ECC
16G 2Rx8 DDR4
2133 ECCSO
16G 2Rx8 DDR4
2133 ECCSO
M4D0-8GS1PCRG
8GB innodisk
DDR4 2133 ECC
MSD0-8GSSQCRG
16GB innodisk
DDR4 2133 ECC
4G 1Rx8 DDR4
2133 ECCSO
D4XS12081
SH21A-A
D4XS1G082
SH21A-B
D4XS12082
SH21A-A
M4D0-4GSSPCRG
M4D0-AGS1QCFG
C94147-0001
C94147-0002
C69768-0063
C69768-0064
C71337-0021
C71337-0022
1604-76367
1604-76368
1549-39956
1549-39961
1604-76363
1604-76362
M0S11601080080001
M0S11601080080002
M0S11601080100001
M0S11601080100002
M0S11601080090001
M0S11601080090002
M0S11601080110001
M0S11601080110002
Test Temp.
(Celsius)
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
85ºC
85ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
25ºC
©Vecow ECS-9700/ 9600 User Manual
Appendix E
106
E.5 Supported Storage Device List
Type mSATA
SATA SSD
SATA HDD
Brand
Intel innodisk
Transcend
Intel innodisk
TOSHIBA
HGST
Model
Intel-310 SSDMAEMC080G2 mSATA 3ME3 DEMSR-
64GD09BW2DC mSATA 3ME3 DEMSR-
A28D09BW2DC mSATA 3ME3 DEMSR-
B56D08BWBQC
SSD420 TS128GSSD420I
SSD420 TS256GSSD420I
SSD370 TS64GSSD370
SSD 540s SSDSC2KW180H6
SSD E 5400s SSDSC2KR120H6
SSD 530 SSDSC2BW120A4
3MG2-P DGS25-64GD81BW1QC
3MG2-P A28D81BW1QC
3MG2-P DGS25-B56D81BW3QC
MQ01ABF050
Z5K500.B-500
Capacity
80GB
64GB
128GB
256GB
128GB
256GB
64GB
180GB
120GB
120GB
64GB
128GB
120GB
500GB
500GB
** If more help is needed, please contact Vecow technical support **
Appendix E
107
For further support information, please visit www.vecow.com
This document is released for reference purpose only.
All product offerings and specifications are subject to change without prior notice.
No part of this publication may be reproduced in any form or by any means, electric, photocopying, or recording, without prior authorization from the publisher.
The rights of all the brand names, product names, and trademarks belong to their respective owners.
© Vecow Co., Ltd. 2016. All rights reserved.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project