User Manual - Mitsubishi Electric Display Solutions

User Manual - Mitsubishi Electric Display Solutions
LAN Control Utility (ProjectorView Global+/ProjectorView)
User Manual
(for WL7200U/XL7100U/UL7400U/WL7050U/XL7000U)
Contents
1. Introduction ............................................................................................................ 2
1.1. Preparing to use network features .......................................................................................... 2
1.2. Functions and features ............................................................................................................ 2
1.3. Operation environment ............................................................................................................ 2
2. Setup ...................................................................................................................... 4
2.1. Installation of “ProjectorView Global+”.................................................................................... 4
2.2. When deleting “ProjectorView Global+” (Uninstallation) ......................................................... 5
3. Main screen ............................................................................................................ 6
3.1. System settings ....................................................................................................................... 8
4. Projector registration .............................................................................................. 9
4.1.
4.2.
4.3.
4.4.
4.5.
Connection............................................................................................................................... 9
Registration of projector to “ProjectorView Global+” ............................................................ 10
When changing the projector IP settings .............................................................................. 12
When changing projector settings......................................................................................... 13
When deleting projector registration ..................................................................................... 13
5. Operation of projector .......................................................................................... 14
5.1. Operation of projector by remote controller .......................................................................... 14
5.2. Confirmation of projector status ............................................................................................ 15
6. Schedule setting................................................................................................... 16
6.1. Creation of projector group ................................................................................................... 16
6.2. When changing schedule setting .......................................................................................... 17
6.3. When deleting group.............................................................................................................. 18
7. E-mail setting........................................................................................................ 19
7.1. Connection with E-mail server............................................................................................... 19
7.2. E-mail setting ......................................................................................................................... 19
7.3. Sending test E-mail................................................................................................................ 19
8. ProjectorView ....................................................................................................... 20
8.1.
8.2.
8.3.
8.4.
8.5.
8.6.
Main functions ....................................................................................................................... 20
Starting ProjectorView ........................................................................................................... 20
Entering projector information ............................................................................................... 23
Setting the network password ............................................................................................... 24
Resetting the network settings .............................................................................................. 24
Alert E-mail setting ................................................................................................................ 25
8.6.1. Alert E-mail function .......................................................................................................................... 25
8.6.2. E-mail setting ..................................................................................................................................... 26
8.6.3. Sending test E-mail ........................................................................................................................... 27
9. Visual PA2 (Visual PA2 enabled projectors only) .................................................. 28
9.1.
9.2.
9.3.
9.4.
9.5.
Starting Visual PA2 ................................................................................................................ 28
Saving messages entered and settings specified in Visual PA2 ........................................... 29
Loading saved data in Visual PA2 ......................................................................................... 29
Deleting data from Visual PA2 ............................................................................................... 29
Configuring the Schedule function of Visual PA2 .................................................................. 30
10. Telnet setup (Telnet enabled projectors only) ....................................................... 31
11. Others................................................................................................................... 32
11.1. Troubleshooting ..................................................................................................................... 32
11.2. Supported Projectors ............................................................................................................ 32
1. Introduction
1.1. Preparing to use network features
This projector is equipped with the network function to control and monitor the projector’s operations and to
send e-mail notification.
Before using the network function, perform the following three preparation steps.
t *OTUBMMJOHUIF1SPKFDUPS7JFX(MPCBM
t "TTJHOJOHUIFQSPKFDUPS*1BEESFTT
t $POmHVSJOHTFUUJOHTTVDIBT1"44803%&NBJM4FUUJOH-BOHVBHFBOE$FSUJmDBUJPO4FUUJOHCZSVOOJOH
Telnet (Telnet enabled projectors only) or using ProjectorView
The projector IP address, password, and certification can be configured on the projector main screen. For more
information, see the section describing network settings provided in the projector's User Manual.
1.2. Functions and features
ProjectorView Global+
t
t
t
t
t
t
t
VOJUTPGQSPKFDUPSTDBOCFSFNPUFDPOUSPMMFEBUUIFNBYJNVN
4FUUJOHTTVDIBTUIF*1BEESFTTPGUIFQSPKFDUPSDBOCFDPOmHVSFE
:PVDBOSFHJTUFSNVMUJQMFQSPKFDUPSTJOBHSPVQBOEDPOUSPMUIFNDPMMFDUJWFMZ
7BSJPVTDPOEJUJPOTPGDPOOFDUFEQSPKFDUPSTDBOCFNPOJUPSFE
4DIFEVMFPGUIFQPXFSTVQQMZ0/0''DBOCFTFUFWFSZHSPVQ
4DIFEVMFPGUIFQPXFSTVQQMZ0/0''DBOCFTFUFWFSZEBZ
8IFOUIFDPNNVOJDBUJPOXJUIUIFQSPKFDUPSNPOJUPSFECZUIFUIFGUEFUFDUPSJTEJTSVQUFEXBSOJOH&NBJMJT
issued to the designated address.
t .FTTBHFDBOCFEJTQMBZFEPOUIFTDSFFOPGUIFPQFSBUJOHQSPKFDUPS7JTVBM1"FOBCMFEQSPKFDUPSTPOMZ
t 5IFQSPKFDUPSJTDBQBCMFPGSFBEJOHBMPVEPOTDSFFONFTTBHFT5FYU4QFFDIFOBCMFEQSPKFDUPSTPOMZ
ProjectorView
t &BDIQSPKFDUPSDBOCFDPOUSPMMFETFQBSBUFMZVTJOHB8FCCSPXTFS
t 8IFOBOFSSPSPSXBSOJOHPDDVSTXJUIUIFQSPKFDUPSXBSOJOH&NBJMJTJTTVFEUPUIFEFTJHOBUFEBEESFTT
1.3. Operation environment
t 4VQQPSUFE04
Windows XP, Windows Vista and Windows 7 (Operation of the projector isn’t guaranteed in a 64-bit version of
any operating system.)
t $16
Higher than the minimum specifications for the above operating systems to work
t .FNPSZ
More than the minimum specifications for the above operating systems to work
t 'SFF)%%TQBDF
32 MB or more (recommended)
t 8FCCSPXTFS8IFOVTJOH1SPKFDUPS7JFX
*OUFSOFU&YQMPSFS7FS7FSBOE7FSSFDPNNFOEFE
(Java Plug-in *1 must be installed and JavaScript must be enabled.)
*1 Installing Java Plug-in:
(1) Download JRE6 from the JAVA download center on the Oracle Web site
IUUQKBWBTVODPNKBWBTFEPXOMPBETJOEFYKTQ
(When this file URL is not a valid location, search for “JRE6 download” using a search engine and access
the download site.)
&YFDVUFUIFEPXOMPBEFEmMF
(3) After installation is complete, disable the cache settings as following procedures.
1. Select [Start] - [Control Panel] - [Java].
2. Select [General] tab and click [Settings...].
3. Click [Delete Files...].
4. Click [OK] in the Delete Temporary Files window.
EN-2
1. Introduction
Microsoft® and Windows® are the registered trademark or trademark of Microsoft Corporation in the United
States and other countries.
(The official name of Windows is Microsoft Windows Operating System.)
Other company names and product names described in this document are the registered trademark or trademark
of the respective holders.
Furthermore, “®” mark and “TM” mark are omitted in this document.
t 8JOEPXT91JTSFGFSSFEUPBT.JDSPTPGU8JOEPXT91)PNF&EJUJPO1SPGFTTJPOBM
t 8JOEPXT7JTUBJTSFGFSSFEUPBT.JDSPTPGU8JOEPXT7JTUB)PNF#BTJD)PNF1SFNJVN#VTJOFTT&OUFSQSJTF
Ultimate.
t 8JOEPXTJTSFGFSSFEUPBT.JDSPTPGU8JOEPXT)PNF#BTJD)PNF1SFNJVN1SPGFTTJPOBM&OUFSQSJTF
Ultimate.
EN-3
2. Setup
2.1. Installation of “ProjectorView Global+”
#FGPSFTUBSUJOHJOTUBMMBUJPOCFTVSFUPSFBEi3FBE.FUYUwDPOUBJOFEJOUIF$%30.
Copy “ProjectorView Global+v3_2.msi” contained in the Tools folder of CD-ROM to the hard disk of your
personal computer.
(1) Double click “ProjectorView Global+v3_2.msi”, and start up the installer of “ProjectorView
Global+”.
(2) The setup window is displayed. Click [Next].
(3) Select the folder to be installed, and click [Next].
<Note>
t 8IFOJOTUBMMJOHi1SPKFDUPS7JFX(MPCBMwUP8JOEPXT7JTUBPS8JOEPXTEPOPUDIBOHFUIFJOTUBMMBUJPO
destination folder.
(4) Click [Next].
t *OTUBMMBUJPOJTTUBSUFE
EN-4
2. Setup
(5) When the installation has been completed, click [Close].
2.2. When deleting “ProjectorView Global+” (Uninstallation)
<Note>
t 8IFOVOJOTUBMMJOHi1SPKFDUPS7JFX(MPCBMwi1SPKFDUPS7JFX(MPCBMwTIPVMECFFOEFEJOBEWBODF*GUIF
application continues operating, uninstallation can not be performed normally.
(1) Double click “ProjectorView Global+v3_2.msi”, and start up the installer of “ProjectorView
Global+”.
(2) Select “Remove ProjectorView Global+”, and click [Finish].
t 5IFVOJOTUBMMBUJPOJTTUBSUFE
(3) When the uninstallation has been completed, click [Close].
t -PHTBOETFUUJOHmMFTBSFOPUBVUPNBUJDBMMZEFMFUFE%FMFUFUIFNNBOVBMMZ
EN-5
3. Main screen
Menu bar
Configuration
:PVDBOTQFDJGZUIFGPMMPXJOHTFUUJOHT
"EE/FX(SPVQ
:PVDBODSFBUFBOFXHSPVQ
&EJU4DIFEVMF4FUUJOH
:PVDBOFEJUTDIFEVMFTFUUJOHTTFUGPSFYJTUJOHHSPVQT
Search Projector:
Automatically searches available projectors.
"TTJHO*1
:PVDBODPOmHVSF*1TFUUJOHTPGUIFQSPKFDUPS
&EJU1SPKFDUPS4FUUJOH
:PVDBOFEJUQSPKFDUPSTFUUJOHT
&EJU&NBJM4FUUJOH
:PVDBODPOmHVSF&NBJMTFUUJOHTVTFEGPSUIJTBQQMJDBUJPO
4FBSDI1SPKFDUPS4FUUJOH
:PVDBOTQFDJGZBTFBSDISBOHFGPSDPNNVOJDBUJPOXJUIUIFQSPKFDUPSWJBB
router.
4ZTUFN$POmHVSBUJPO
:PVDBODPOmHVSFTZTUFNTFUUJOHTPGUIJTBQQMJDBUJPO
Help
The version information is displayed.
Tool bar
ProjectorView
Telnet
Visual PA2
Remote Controller
Refresh Status
Select All
Exit
:PVDBODPOUSPMFBDIQSPKFDUPSTFQBSBUFMZVTJOHB8FCCSPXTFS*ODBTFPGBOFSSPSJO
the projector, the details of the error are displayed. For details, see page 20.
:PVDBONBLFWBSJPVTTFUUJOHTVTJOH5FMOFU5FMOFUFOBCMFEQSPKFDUPSTPOMZ
:PVDBOTFUUIFQBTTXPSE1SPKFDUPS7JFXEJTQMBZMBOHVBHF-"/DPOUSPMBOE
certification. For details, see page 31.
:PVDBOEJTQMBZBMJOFPGBOZUFYUPOUIFQSPKFDUPSTDSFFO7JTVBM1"FOBCMFE
projectors only). For details, see page 28.
3FNPUF$POUSPMMFSXJOEPXDBOCFEJTQMBZFEUPPQFSBUFUIFQSPKFDUPS:PVDBOUVSO
POPGGUIFQPXFSBOETFMFDUUIFJOQVUTPVSDF
The current status of Power, Input Source, AV Mute, and Lamp Time (Low) of the
projectors being displayed in the projector list can be reacquired. The status of Input
Source and AV Mute will not be obtained under the following conditions:
t XIFOUIFQSPKFDUPSJTQPXFSFEPGG
t EVSJOHXBSNVQPSDPPMEPXO
"MMQSPKFDUPSTDVSSFOUMZEJTQMBZFEPOUIFQSPKFDUPSMJTUDBOCFTFUUPTFMFDUFEOPO
selected state.
:PVDBOFYJUi1SPKFDUPS7JFX(MPCBMw)PXFWFSZPVDBOOPUFYJUUIFBQQMJDBUJPO
during the automatic projector search and the projector status refreshing. Even
EVSJOHUIFQSPKFDUPSTUBUVTBDRVJTJUJPOZPVDBOFYJUUIFBQQMJDBUJPOGPSDFGVMMZCZ
clicking the
button at the upper right corner of the main screen. In this case,
Windows warning message is displayed.
EN-6
3. Main screen
Group Name
Group of the projector can be selected. When you select “All”, all the registered
projectors are displayed. Newly created group(s) are added to the list. When you
select your choice of group, all projectors that belong to the selected group are
displayed.
Status tag
Property and status of the projector can be indicated. When clicking each tag button
FYDFQUUIF."$BEESFTT
UIFMJTUDBOCFSFBSSBOHFETPSUFE
Projector list display column
List of the projector which belongs to the selected group can be displayed. Status of
the projector can also be displayed. The display color changes as follows depending
on the condition of the projector:
Black:
In normal condition
Red:
In abnormal condition ( Check the abnormal condition by ProjectorView.
When the communication fails, see “11.1. Troubleshooting.”)
Black (yellow background):
Warning about the lamp lifetime
White (red background):
The communication with the projector monitored by the theft detector has
been disrupted. ( Check the condition. There is a possibility of theft.)
Gray:
In communication inoperable condition
Error Message
Error messages detected in communicating with the projector can be displayed.
Operation status display column
Operation status of “ProjectorView Global+” can be indicated. Operation status
during communication processing by remote-controlling and schedule can be
indicated.
EN-7
3. Main screen
3.1. System settings
(1) Select “System Configuration” from “Configuration” of the menu bar on the main screen.
t i4ZTUFN$POmHVSBUJPOwXJOEPXJTEJTQMBZFE%FGBVMUTFUUJOHTBSFTIPXOJOUIFGPMMPXJOHFYBNQMF
Item
Description
-BOHVBHF
3FGSFTI4UBUVT$ZDMF
:PVDBOTFMFDUUIFVTFSJOUFSGBDFMBOHVBHF+BQBOFTFPS&OHMJTI
:PVDBOTFUUIFDZDMFUPPCUBJOUIFQSPKFDUPSTUBUVT4FMFDUBOJOUFHFSWBMVFXJUI
no decimal part from 1 to 60 minutes.
(2) Change the settings as needed and click [Save].
t 5PVQEBUFUIFTFUUJOHTZPVDIBOHFEJUJTOFDFTTBSZUPSFTUBSUi1SPKFDUPS7JFX(MPCBMw
EN-8
4. Projector registration
4.1. Connection
Connect the controller PC and the projector, which have installed “ProjectorView Global+”, to a commercially
available LAN cable.
When connecting multiple projectors, use a commercially available hub.
t "-"/UFSNJOBMJTSFRVJSFEGPSUIFDPOUSPMMFS1$
t 6TFB-"/DBCMFDPNQBUJCMFXJUI$BUFHPSZBOE#"4&5
6TFBDSPTTPWFS-"/DBCMFJOUIFDBTFPGDPOOFDUJPOFYBNQMFBOEVTFBTUSBJHIUUISPVHI-"/DBCMFJOUIF
DBTFPGDPOOFDUJPOFYBNQMF
*OUIFDBTFPGDPOOFDUJPOFYBNQMFTFFUIFJOTUSVDUJPONBOVBMPGUIFSPVUFS
t %POPUUPVDINFUBMQBSUTPGUIF-"/UFSNJOBMBOE-"/DBCMFCZIBOETDIBSHFEPGTUBUJDFMFDUSJDJUZ%JTDIBSHF
of static electricity may cause a failure of the projector.
t 6QUPVOJUTPGUIFQSPKFDUPSTDBOCFSFHJTUFSFEBUUIFNBYJNVN
<Note>
t 5IF-"/GVODUJPONBZCFVOBWBJMBCMFEFQFOEJOHPOUIFTUBOECZNPEFTFUUJOHPGUIFQSPKFDUPS5PFOBCMFUIF
LAN function, change the setting referring to the User Manual of your projector.
Connection example 1
Controller PC
Projector
Commercially available LAN cable
(Crossover cable)
Connection example 2
Projector
Controller PC
&YUFSOBMIVC
Commercially available LAN cable
(Straight-through cable)
Connection example 3
Projector
Router
Projector
Controller PC
&YUFSOBMIVC
&YUFSOBMIVC
EN-9
4. Projector registration
4.2. Registration of projector to “ProjectorView Global+”
5IFQSPDFEVSFTUPSFHJTUFSQSPKFDUPSTWBSZBNPOHUIFGPSFHPJOHDPOOFDUJPOFYBNQMFT
t *ODPOOFDUJPOFYBNQMFTBOEXIFSFQSPKFDUPSTBSFJOTUBMMFEXJUIJOUIFTBNFMPDBMOFUXPSL
UIFQSPKFDUPST
within such network are automatically detected and registered. For details, see procedure A below.
t *ODPOOFDUJPOFYBNQMFXIFSFQSPKFDUPSTBSFJOTUBMMFEWJBBSPVUFS
TQFDJGZUIFSBOHFPGUIFQSPKFDUPST*1
addresses and then carry out automatic projector search within the range to register projectors. For details,
see procedure B below.
t 6QUPVOJUTPGQSPKFDUPSTDBOCFSFHJTUFSFEBUUIFNBYJNVN
t 1SPKFDUPSTUIBUIBWFKVTUCFFOSFHJTUFSFECZUIFBVUPNBUJDQSPKFDUPSTFBSDIBSFOUCFMPOHJOHUPBOZHSPVQ
When the projectors you registered aren’t displayed on the projector list on the main screen, select “All” from
the group select pull-down menu.
Procedure A - For connection examples 1 and 2 (where projectors are installed within the
same local network)
(1) Start up “ProjectorView Global+”.
(2) Select “Search Projector” from “Configuration” of the menu bar on the main screen.
t 5IFQSPKFDUPSTDPOOFDUFEUP-"/BSFTFBSDIFEBVUPNBUJDBMMZ
t 4PNFQSPKFDUPSTNBZSFRVJSFZPVUPFOUFSUIFQBTTXPSEXIFOFTUBCMJTIJOHQSPKFDUPSDPOOFDUJPOTGPSUIFmSTU
time. If the projector password is changed, you need to enter that new password.
<Note>
t &OTVSFUIBUUIF*1BEESFTTPGUIF1$BOEUIBUPGUIFQSPKFDUPSBSFJOUIFTBNFOFUXPSLHSPVQ5IFMBTUPDUFU
of the IP address should contain a different value.)
t #FTVSFUPNBLFBOPUFPGUIF*1BEESFTTFTZPVTFU*GZPVGPSHFUUIF*1BEESFTTFTZPVNBZOPUCFBCMFUP
detect the projectors again.
t "UJOJUJBMTFUVQ%)$1PS"VUP*1UISPVHI
BVUPNBUJDBMMZBTTJHOTBO*1BEESFTT
Note that a different IP address may be assigned every time you start the projectors. If a connection cannot
CFFTUBCMJTIFEFYFDVUFi4FBSDI1SPKFDUPSw
t *GZPVDIBOHFUIF*1BEESFTTJOUIFQSPKFDUPSNFOVBGUFSUIFQSPKFDUPSTIBWFCFFOEFUFDUFEFYFDVUFi4FBSDI
Projector” again.
t *UJTSFDPNNFOEFEUIBUZPVBTTJHOBO*1BEESFTTPGUIFQSPKFDUPSUPUIFmYFE*1BEESFTT
t *GTFWFSBMQSPKFDUPSTXJUIUIFTBNF*1BEESFTTBSFSFHJTUFSFEEFMFUFUIFPOFTXIJDIBSFOPUDPOOFDUFEUPUIF
network from “Edit Projector Setting”.
EN-10
4. Projector registration
Procedure B - Connection example 3 (where projectors are installed via a router)
To automatically detect projectors connected via a router, confirm the IP address in the projector network menu
and specify a range of IP addresses to search that particular IP address using “Search Projector Setting”.
<Note>
If you want to connect a projector via a router after automatically detecting it, you need to specify a search range
of IP addresses that includes the projector's IP address in advance.
(1) Start up “ProjectorView Global+”.
(2) Select “Search Projector Setting” from “Configuration” of the menu bar.
t i4FBSDI1SPKFDUPS4FUUJOHwXJOEPXJTEJTQMBZFE
Item
Description
Start IP Address
Specify the IP address that is the start of the search range.
:PVDBOOPUTQFDJGZBO*1BEESFTTUIBUDPOUBJOTBSBOHFPUIFSUIBOUPGPS
the first and last octets and a range other than 0 to 255 for the second and third
octets.)
4QFDJGZUIFMBTUPDUFUPGUIF*1BEESFTTUIBUJTUIFFOEPGUIFTFBSDISBOHF:PV
cannot specify a value that contains a number other than 1 to 254. In addition,
you cannot specify a value that is smaller than the last octet of the search start IP
address specified in step .)
The settings you made are saved and then the automatic projector search is
performed.
&OE*1"EESFTT
Search Projector
(3) Specify the projector search range by IP address ( and ).
t 6QUPTFBSDISBOHFTDBOCFTFU4FUUJOHTDBOCFDPOmHVSFEGPSFBDIMJOFPGUIFTFBSDISBOHF
(4) To save the settings, click [Save]. To continue the projector search, click [Search Projector].
t 8IFOZPVDMJDL<4BWF>UIFTFBSDISBOHFTZPVTQFDJGZBSFTBWFEBOEUIFi4FBSDI1SPKFDUPS4FUUJOHwXJOEPX
is closed.
t 8IFOZPVEPOhUXBOUUPTBWFUIFTFBSDISBOHFTDMJDL<$BODFM>UPDMPTFUIFi4FBSDI1SPKFDUPS4FUUJOHw
window.
t "GUFSTBWJOHUIFTFUUJOHTCZTFMFDUJOHi$POmHVSBUJPOwPOUIFNFOVCBSBOEUIFOTFMFDUJOHi4FBSDI
Projector”, you can perform automatic projector search within the search ranges you saved.
t 4PNFQSPKFDUPSTNBZSFRVJSFZPVUPFOUFSUIFQBTTXPSEXIFOFTUBCMJTIJOHQSPKFDUPSDPOOFDUJPOTGPSUIF
first time. Authentication is automatically performed from the second time onwards unless projectors are
deleted from the list.
EN-11
4. Projector registration
<Note>
t 4FUUIFEFGBVMUHBUFXBZTPGUIFQSPKFDUPSTBOE1$DPSSFDUMZ'PSEFUBJMTDPOUBDUZPVSOFUXPSLBENJOJTUSBUPS
t #FTVSFUPNBLFBOPUFPGUIF*1BEESFTTFTBOEEFGBVMUHBUFXBZTZPVTFU*GZPVGPSHFUUIFTFUUJOHWBMVFTZPV
may not be able to detect the projectors again.
t "UJOJUJBMTFUVQ%)$1PS"VUP*1UISPVHI
BVUPNBUJDBMMZBTTJHOTBO*1BEESFTT
Note that a different IP address may be assigned every time you start the projectors. If a connection cannot
CFFTUBCMJTIFEFYFDVUF4FBSDI1SPKFDUPS
t *GZPVDIBOHFUIF*1BEESFTTJOUIFQSPKFDUPSNFOVBGUFSUIFQSPKFDUPSTIBWFCFFOEFUFDUFEFYFDVUFi4FBSDI
Projector” again.
t *UJTSFDPNNFOEFEUIBUZPVBTTJHOBO*1BEESFTTPGUIFQSPKFDUPSUPUIFmYFE*1BEESFTT
4.3. When changing the projector IP settings
:PVDBODIBOHFUIFQSPKFDUPS*1TFUUJOHT
(1) Select the projector which you like to change from the projector list on the main screen.
(2) Select "Assign IP" from “Configuration” of the menu bar on the main screen.
t i"TTJHO*1wXJOEPXJTEJTQMBZFE
(3) To automatically assign an IP address, select [Auto] and then select DHCP. To manually
assign an IP address, select [Manual] and enter values for IP Address, Subnet Mask, and
Default Gateway.
Item
Description
DHCP
IP Address
Subnet Mask
Default Gateway
Obtain an IP address via a DHCP server.
Enter an IP address.
Enter the subnet mask.
Enter the default gateway address.
<Note>
t "OFSSPSEJBMPHGPSUIFGUEFUFDUJPONBZCFEJTQMBZFEBGUFSUIF*1TFUUJOHTIBWFCFFODIBOHFE
t *GBDPOOFDUJPODBOOPUCFFTUBCMJTIFEBGUFSUIF*1TFUUJOHTIBWFCFFODIBOHFEFYFDVUFi4FBSDI1SPKFDUPSw
t *GZPVXBOUUPDIBOHFUIF*1BEESFTTPGBQSPKFDUPSDPOOFDUFEWJBBSPVUFSZPVOFFEUPTQFDJGZBTFBSDISBOHF
of IP addresses that includes the new IP address in “Search Projector Setting”.
t $POTVMUZPVSOFUXPSLBENJOJTUSBUPSBCPVUUIFTVCOFUNBTLBOEEFGBVMUHBUFXBZJOBEWBODF
EN-12
4. Projector registration
4.4. When changing projector settings
(1) Select the projector which you like to change from the projector list on the main screen.
(2) Select “Edit Projector Setting” from “Configuration” of the menu bar.
t i&EJU1SPKFDUPS4FUUJOHwXJOEPXJTEJTQMBZFE
(3) Set the Projector Name and its group and the theft detector.
Item
Description
Projector Name
MAC Address
IP Address
Enter the projector name within 64 characters in one-byte alphanumeric symbol.
The MAC address is displayed. The displayed address cannot be changed.
The IP address is displayed. The displayed address cannot be changed. When it
is required to change the IP address, use [Assign IP].
From the pull-down menu, select the group to which the projector is belonging.
(A new group can be created by clicking [Add New Group]. See “6.1. Creation
of projector group”.)
Turn on or off the theft detector.
Group Name
Theft Check
<Note>
In right-click menu also, the setting of the projector can be changed. (Multiple projectors can be selected.)
t "EEUP/FX(SPVQ
"EEJUJPOUPBOFXMZDSFBUFEHSPVQ
t "EEUP&YJTUJOH(SPVQ $IBOHFPGUIFCFMPOHJOHHSPVQ
t 5IFGU$IFDL4FUUJOH
$IBOHFPGUIFGUEFUFDUPSTFUUJOH0/0''
4.5. When deleting projector registration
(1) Select the projector which you like to delete from the projector list on the main screen.
(2) Select “Edit Projector Setting” from “Configuration” of the menu bar.
t i&EJU1SPKFDUPS4FUUJOHwXJOEPXJTEJTQMBZFE
(3) Click [Delete].
t 5IFTFMFDUFEQSPKFDUPSJTEFMFUFE
EN-13
5. Operation of projector
5.1. Operation of projector by remote controller
Group or single unit of projector can be operated.
(1) Select the projector which you like to operate from the projector list on the main screen.
t 8IFOTFMFDUJOHNPSFUIBOPOFQSPKFDUPSTJNVMUBOFPVTMZTFMFDUXIJMFQSFTTJOHUIF$USMLFZ
(2) Click [Remote Controller] of the tool bar on the main screen or when you like to operate a
certain projector, double click the projector on the projector list on the main screen.
t i3FNPUF$POUSPMMFSwXJOEPXJTEJTQMBZFE
(3) Operate the projector by selecting each operating button on the window.
Command
Button
Description
Power
Power ON
Power OFF
Turn on the power supply of the projector.
Turn off the power supply of the projector.
Input Source
COMPUTER 1
COMPUTER 2
VIDEO
S-VIDEO
HDMI *1
DVI-D *1
DIGITAL 3
NETWORK
STORAGE 1
STORAGE 2
COMPONENT
Change the input signal to COMPUTER 1.
Change the input signal to COMPUTER 2.
Change the input signal to VIDEO.
Change the input signal to S-VIDEO.
Change the input signal to HDMI *1.
Change the input signal to DVI-D *1.
Change the input signal to DIGITAL 3.
Change the input signal to NETWORK.
Change the input signal to STORAGE 1.
Change the input signal to STORAGE 2.
Change the input signal to COMPONENT.
&YJU
$MPTFUIF3FNPUF$POUSPMMFSXJOEPX
*1 HDMI and DVI-D are displayed with DIGITAL 1 or DIGITAL 2 by a connected projector.
<Note>
t 5IFOFYUPQFSBUJPODBOOPUCFQFSGPSNFEVOUJMUIFQSFWJPVTPQFSBUJPOIBTCFFODPNQMFUFE
t 5IFPQFSBUJPODBOOPUCFQFSGPSNFEEVSJOHSFPCUBJOJOHSFGSFTIJOH
UIFQSPKFDUPSTUBUVT
t "WBJMBCMFJOQVUTPVSDFTWBSZEFQFOEJOHPOUIFUZQFPGQSPKFDUPST:PVDBOOPUTFMFDUJOQVUTPVSDFTUIBUBSFOU
supported by the projector.
EN-14
5. Operation of projector
5.2. Confirmation of projector status
The status of the projector is displayed on the projector list on the main screen.
Item
Description
$IFDL
No.
Projector Name
MAC Address
IP Address
1PXFS
Input Source *1
5IFGUEFUFDUPSTFUUJOH0/0''
Projector list registration number
Projector name set in the application
MAC address of the projector
IP address of the projector
1PXFSTVQQMZTUBUVTPGUIFQSPKFDUPS0/0''
*OQVUTJHOBMPGUIFQSPKFDUPS$0.165&3$0.165&37*%&047*%&0
)%.*)%.*)%.*
%7*%4%*1$-FTT1SFTFOUBUJPO64#%JTQMBZ-"/%JTQMBZ
COMPONENT)
.VUFTUBUVTPGUIFQSPKFDUPS0/0''
-BNQJMMVNJOBUJOHUJNF))))..
In the case of the projector equipped with two lamps, illuminating time for
the lamp 1 is displayed in the left side and illuminating time for the lamp 2 is
displayed in the right side.
The belonging group of projector
"7.VUF
-BNQ5JNF-PX
Group Name
*1 HDMI and DVI-D are displayed with DIGITAL 1 or DIGITAL 2 by a connected projector.
t 5IFQSPKFDUPSTUBUVTJTSFPCUBJOFESFGSFTIFE
BVUPNBUJDBMMZBOEQFSJPEJDBMMZCVUUIFQSFTFOUTUBUVTDBO
also be obtained by the user’s instruction. When clicking [Refresh Status] of the tool bar on the main screen,
1PXFS*OQVU4PVSDF"7.VUFBOE-BNQ5JNF-PX
TUBUVTPGFBDIQSPKFDUPSJTSFPCUBJOFE
t 5IFTUBUVTPG*OQVU4PVSDFBOE"7.VUFXJMMOPUCFPCUBJOFEVOEFSUIFGPMMPXJOHDPOEJUJPOT
- when the projector is powered off
- during warm-up or cool-down.
t 8IFODMJDLJOHUIFTUBUVTUBHPGUIFQSPKFDUPSMJTUFYDFQUUIF."$BEESFTT
UIFMJTUDBOCFSFBSSBOHFETPSUFE
The list can be rearranged in reversed order by pressing one more time.
t 8IFODMJDLJOH<4FMFDU"MM>PGUIFUPPMCBSBMMQSPKFDUPSTJOUIFQSPKFDUPSMJTUCFDPNFTFMFDUFEOPOTFMFDUFE
state.
t *GBOZBCOPSNBMTUBUFPGUIFQSPKFDUPSJTEFUFDUFECZBDRVJSJOHUIFQSPKFDUPSTUBUVTBOFSSPSNFTTBHFXJMMCF
displayed on the error message display column at the lower part of the screen.
<Note>
t 5IFEFGBVMUDZDMFPGUIFBVUPNBUJDSFBDRVJTJUJPOJTNJOVUFT5PDIBOHFUIJTDZDMFTFFi4ZTUFN
settings.”
t 8IFONVMUJQMFQSPKFDUPSTBSFDPOOFDUFEJUNBZUBLFUJNFUPBDRVJSFUIFTUBUVT%VSJOHBDRVJSJOHUIFTUBUVT
the status bar at the lower part of the main screen becomes “Getting status...”, and it becomes “Done” when
the acquisition has been completed.
EN-15
6. Schedule setting
6.1. Creation of projector group
Multiple projectors can be controlled and batched by sorting groups.
"MTPFBDIHSPVQDBOTFUFBDIUJNFPGUIFQPXFSTVQQMZ0/0''FWFSZEBZ
4JODFUIFTDIFEVMFPGUIFQPXFSTVQQMZ0/0''JTQFSGPSNFECZFBDIHSPVQUIFQSPKFDUPSXIJDIZPVMJLFUP
operate at the same schedule should be integrated into the same group.
When Power ON and Power OFF are enabled, their time settings are indicated on the schedule list.
[Example] When setting the schedule for the group “group 1” to turn the power supply ON at 9:00 on Monday,
turning OFF at 17:00 on the same day, ON at 8:30 on Thursday, and OFF at 17:40 on Friday.
Group name
Day of the week
Time of power supply ON
Time of power supply OFF
When validating the setting,
QVUBDIFDLNBSLJOUIFCPY
Schedule list
5JNFPGQPXFSTVQQMZ0/0''
(1) Select “Add New Group” from “Configuration” of the menu bar.
t i"EE/FX(SPVQwXJOEPXJTEJTQMBZFE
(2) Input the group name to be created in the “Group Name” column (within 16 characters in
one-byte alphanumeric symbol).
(3) Select the day of the week to be set for the time of the power supply ON/OFF.
(4) Only when setting the time of the power supply ON, set the time in the “Power ON” column,
and put a check mark in the “Enable” box.
(5) Only when setting the time of power supply OFF, set the time in the “Power OFF” column,
and put a check mark in the “Enable” box.
(6) When there are more than one day of the week to be set for the power supply ON/OFF
schedule, repeat the procedure (3) to (5).
(7) Click [Add].
EN-16
6. Schedule setting
<Note>
t 5IFQPXFSTVQQMZ0/BOEUIFQPXFSTVQQMZ0''DBOOPUCFTFMFDUFEBUUIFTBNFUJNFPGUIFTBNFEBZPGUIF
week.
t 5IF4DIFEVMF4FUUJOHXJMMCFFYFDVUFEXIJMFi1SPKFDUPS7JFX(MPCBMwJTJOPQFSBUJPO
t %FQFOEJOHPOVTBHFDPOEJUJPOTTVDIBTXIFOUIFSFBSFTPNBOZQSPKFDUPSTUIBUZPVOFFEUPDPOUSPMUIFUJNF
UPCFFYFDVUFECZUIFQPXFSTVQQMZDPOUSPMNBZEFWJBUFGSPNUIFTFUUJOHUJNFPGUIFTDIFEVMF
t 8IFOVUJMJ[JOHUIF/FUXPSL5JNF1SPUPDPM/51
GVODUJPOPOUIF*OUFSOFUUIFTDIFEVMFPQFSBUJPONBZOPUCF
FYFDVUFECFDBVTFUIFTFUUJOHUJNFPGUIFTDIFEVMFKVNQTPWFS
t 8IFOUIFBVUPNBUJDUJNFBEKVTUNFOUCZTVNNFSUJNFJTWBMJEUIFTDIFEVMFPQFSBUJPONBZOPUCFFYFDVUFE
because the time is automatically adjusted before and after switching over.
6.2. When changing schedule setting
(1) Select a group which you like to change from the Group select pull-down menu on the main
screen.
(2) Select “Edit Schedule Setting” from “Configuration” of the menu bar.
t i&EJU4DIFEVMF4FUUJOHwXJOEPXJTEJTQMBZFE
(3) Change the contents which you like to correct, and click [Save].
t $PSSFDUFEDPOUFOUTBSFSFnFDUFE
EN-17
6. Schedule setting
6.3. When deleting group
(1) Select the group which you like to delete from the Group select pull-down menu on the main
screen.
(2) Select “Edit Schedule Setting” from “Configuration” of the menu bar.
t i&EJU4DIFEVMF4FUUJOHwXJOEPXJTEJTQMBZFE
(3) Click [Delete].
t 5IFTFMFDUFEHSPVQJTEFMFUFE
<Note>
t 8IFOEFMFUJOHBHSPVQUIFQSPKFDUPSXIJDIIBTCFMPOHFEUPUIFSFMFWBOUHSPVQXJMMOPUCFMPOHUPBOZHSPVQ
Set a new group to belong again on “Edit Projector Setting” window.
EN-18
7. E-mail setting
When the communication with the projector monitored by the theft detector is disrupted, a warning E-mail can be
sent to the designated address, enabling to serve for early detection of the projector theft.
The E-mail setting can not be set at every projector and every group. The same setting should be set for all
projectors.
7.1. Connection with E-mail server
Connect the E-mail server to the network to which the controller PC and the projector are connected that
“ProjectorView Global+” is operating.
7.2. E-mail setting
Designate the address of the E-mail server and the address of the destination to be sent.
<Note>
t "TGPSUIFOFUXPSLFOWJSPONFOUDPOmSNUPUIFOFUXPSLBENJOJTUSBUPS
(1) Select “Edit E-mail Setting” from “Configuration” of the menu bar on the main screen.
t i&EJU&NBJM4FUUJOHwXJOEPXJTEJTQMBZFE
(2) Input the setting item for the network environment, and click [Save].
Item
&NBJM4FSWFS4.51
Description
Destination E-mail Address
&
OUFSUIF*1BEESFTTPGUIF&NBJMTFSWFS&YBNQMF
PS
JOQVUUIFTFSWFSOBNF&YBNQMFNBJMFYBNQMFDPN
Enter the destination E-mail address using up to 64 single-byte
DIBSBDUFST6QUPQMBDFTDBOCFEFTJHOBUFEBUUIFNBYJNVN
7.3. Sending test E-mail
After completing the setting of the each item on the E-mail Setting window, a test E-mail can be sent to confirm
whether the E-mail is correctly delivered to the destination. When clicking [Test E-mail] at the upper right on
the Email Setting window, the test E-mail is issued. Confirm whether the E-mail is correctly delivered to the
destination address.
<Note>
t 5IF&NBJMGVODUJPOXJMMCFFYFDVUFEXIJMFi1SPKFDUPS7JFX(MPCBMwJTJOPQFSBUJPO
t *GUIFUFTU&NBJMJTOPUDPSSFDUMZSFDFJWFEDPOmSNUIFBEESFTTPGUIF&NBJMTFSWFSBOEUIFEFTUJOBUJPOBOE
the connection status of the network. For details, make an inquiry to the network administrator.
t 5IF&NBJMNBZQPTTJCMZOPUCFEFMJWFSFEEFQFOEJOHPOUIFDFSUJmDBUJPOGVODUJPOPGUIF&NBJMTFSWFS'PS
details, make an inquiry to the network administrator.
t 8IFOUIFDPNNVOJDBUJPOXJUIUIFQSPKFDUPSNPOJUPSFECZUIFUIFGUEFUFDUPSJTEJTSVQUFEBUIFGUDIFDLFSSPS
dialog is displayed.
However, the projector list isn’t updated at the same time because it takes some time to update the list.
EN-19
8. ProjectorView
ProjectorView is a web-browser based remote control and monitoring tool for network projectors. If you use the
projectors listed in page 32, see ProjectorView in “LAN Control Utility” User Manual included with the projector.
<Note>
t 8IFO$3&4530/JTTFMFDUFEXJUIUIFOFUXPSLNFOVJUCFDPNFTUIF8FCDPOUSPMGPS$3&4530/
8.1. Main functions
t *UEJTQMBZTUIFTUBUVTPGOFUXPSLQSPKFDUPSTTVDIBTUIFOBNFPGUIFQSPKFDUPSMBNQUFNQFSBUVSFMBNQIPVST
errors and alerts).
t *UDPOUSPMTOFUXPSLQSPKFDUPSTTVDIBTQPXFSJOHPOBOEPGGOFUXPSLQSPKFDUPSTBOETXJUDIJOHJOQVUPSMBNQ
modes).
t *UTFOETBO&NBJMOPUJmDBUJPOXIFOBOFSSPSPSXBSOJOHPDDVST
8.2. Starting ProjectorView
(1) Select the projector that you want to operate from the list of projectors on the main screen.
t 4UBSU1SPKFDUPS7JFXGPSPOFQSPKFDUPSBUBUJNF:PVDBOOPUDPODVSSFOUMZVTF1SPKFDUPS7JFXGPSNVMUJQMF
projectors.
(2) Click [ProjectorView] in the tool bar on the main screen.
t 5IF8FCCSPXTFSMBVODIFTBVUPNBUJDBMMZ5IFQBTTXPSEFOUSZXJOEPXJTUIFOEJTQMBZFE
<Note>
t :PVDBOTUBSU1SPKFDUPS7JFXCZNBOVBMMZUZQJOHUIFQSPKFDUPS*1BEESFTTJOZPVSXFCCSPXTFSTBEESFTT
bar.
t *GZPVBSFVTJOHBQSPYZTFSWFSEPOPUFOBCMFQSPYZTFUUJOHTXIFOBDDFTTJOHUIFQSPKFDUPS*1BEESFTT
t 6QUPUISFF1SPKFDUPS7JFXVOJUTDBOCFVTFEUPDPOUSPMBTJOHMFQSPKFDUPS
(3) Enter the password and click [OK]. (The default password is “admin”.)
t i1SPKFDUPS7JFXwNBJOXJOEPXJTEJTQMBZFE
<Note>
t 5IFDPOOFDUJPOXJMMUVSOPGGJOmWFNJOVUFTBGUFSUIFQBTTXPSEFOUSZXJOEPXJTEJTQMBZFE:PVDBOOPUFOUFS
the password then. If this happens, restart the ProjectorView.
EN-20
8. ProjectorView
ProjectorView main window (PROJECTOR INFORMATION)
When you click PROJECTOR INFORMATION, the Projector Information window is displayed. To display the
information, enter data in the Setup window.
Click [PROJECTOR INFORMATION]
to display the window on the left.
Click [REMOTE CONTROL] to
display the main window (REMOTE
CONTROL).
Click [ALERT E-MAIL] to display the
main window (ALERT E-MAIL).
Click [SETUP] to display the Setup
window. (See page 23.)
If there is something wrong with the
projector, the red warning indicator
lights.
Details are displayed in the column
below by pointing the cursor to the
contents of failures.
“Filter change advice” works only
PO8-69-66-6
<Note>
See your projector User Manual for
the information on when you should
replace the lamp.
<Note>
t *GMBNQNPEFJTTFUUPi45"/%"3%wi-BNQUJNFwEJTQMBZFENBZCFMPOHFSUIBOi0QFSBUJPOUJNFw
ProjectorView main window (REMOTE CONTROL)
8IFOZPVDMJDL3&.05&$0/530-UIF3FNPUF$POUSPMXJOEPXJTEJTQMBZFE:PVDBODMJDLUIFCVUUPOT
EJTQMBZFEJOUIFXJOEPXUPSFNPUFMZDPOUSPMUIFQSPKFDUPS#VUUPOTXJUISFEUFYUTIPXUIFQSPKFDUPSTDVSSFOU
TUBUVT5IFTUBUVTEJTQMBZFEJOUIJTXJOEPXJTVQEBUFEJOSFHVMBSJOUFSWBMT:PVDBOBMTPNBOVBMMZVQEBUFUIF
status by clicking GET STATUS.
Click [REMOTE CONTROL] to
display the window on the left.
Click [PROJECTOR INFORMATION]
to display the main window
(PROJECTOR INFORMATION).
Click [ALERT E-MAIL] to display the
main window (ALERT E-MAIL).
Click to obtain the status of the
projector. The window is updated
simultaneously.
<Note>
It may take time to update the
window.
These are virtual remote control
buttons.
For details, see the description of
UIFSFNPUFDPOUSPMCVUUPOLFZJO
User Manual.
These buttons are used to control the projector’s power, input source, and lamp mode.
The number of input switches that can be displayed vary depending on the type of projector you use.
See your projector User Manual for more information.
Lamp mode cannot be switched when the projector is muted.
EN-21
8. ProjectorView
ProjectorView main window (ALERT E-MAIL)
When you click ALERT E-MAIL, the Alert E-mail window is displayed.
To display the settings of the alert E-mail, configure the settings on the Alert E-mail Setup window.
Click [ALERT E-MAIL] to display the
window on the left.
Click [PROJECTOR INFORMATION]
to display the main window
(PROJECTOR INFORMATION).
Click [REMOTE CONTROL] to
display the main window (REMOTE
CONTROL).
Click [SETUP] to display the Alert
E-mail Setup window. (See “8.6.
Alert E-mail setting”.)
Click to send a test E-mail.
EN-22
8. ProjectorView
8.3. Entering projector information
(1) Click [SETUP] in the ProjectorView main window (PROJECTOR INFORMATION).
t 4FUVQXJOEPXJTEJTQMBZFE
<Note>
t #FTVSFUPFOUFSEBUBXJUIJOmWFNJOVUFTBGUFSUIF4FUVQXJOEPXJTEJTQMBZFE$MJDL0,UPTBWFDIBOHFT
The connection will turn off in five minutes after the window is displayed so you need to go back to the
main window (PROJECTOR INFORMATION) to access the Setup window.
(2) Enter data in each field, choose Language between Japanese and English, set Certification
setting to ON or OFF, specify Password setting, and choose to [RESET] Network setting
reset.
<Note>
t 8IFOZPVDIBOHFUIF-BOHVBHFTFUUJOHCFTVSFUPSFTUBSUUIF1SPKFDUPS7JFXGPSUIFDIBOHFTUPUBLFFGGFDU
5IFGPMMPXJOHUBCMFFYQMBJOTFBDIJUFN
Item
Description
Projector name
Installed date *1
Installed location *1
Last lamp replaced date *1
Last maintenance date *1
Language
Certification setting
Password setting
Enter a unique name to identity the projector.
Enter the date when the projector is installed.
Enter the place where the projector is located.
Enter the date when the last change of lamp was made.
Enter the date when the last maintenance was done.
Choose the display language of ProjectorView (Japanese or English).
Choose whether to set the network certification setting.
Click [PASSWORD] to access the network password setting window. (For
details, see “8.4. Setting the network password”.)
Click [RESET] to access the network settings reset window. (For details, see
“8.5. Resetting the network settings”.)
Network setting reset
*1 'PSEBUBFOUSZVTFTJOHMFCZUFBMQIBOVNFSJDBMDIBSBDUFSTBOETZNCPMT@ ]<>\
^' @ ).
EN-23
8. ProjectorView
8.4. Setting the network password
(1) Click [PASSWORD] in the Setup window.
t 5IFXJOEPXBQQFBSTUPFOUFSUIFDVSSFOUOFUXPSLQBTTXPSE
(2) Enter the current network password and click [OK]. (The default is "admin".)
t *GUIFQBTTXPSEJTDPSSFDUBOPUIFSXJOEPXBQQFBSTUPFOUFSBOFXPOF
t *GUIFQBTTXPSEJTXSPOHBOFSSPSNFTTBHFJTEJTQMBZFE8IFOZPVDMJDL<0,>UIFDVSSFOUOFUXPSL
password window reappears.
(3) Enter the New network password and Confirm network password, and then click [OK].
t *GQBTTXPSETFOUFSFENBUDIUIFXJOEPXDMPTFTUPTBWFUIFDIBOHFT
t *GQBTTXPSETFOUFSFEEPOPUNBUDIBOFSSPSNFTTBHFJTEJTQMBZFE8IFOZPVDMJDL<0,>UIFOFXOFUXPSL
password window reappears.
8.5. Resetting the network settings
When you reset the network settings, all data and settings specified in 8.3. Entering projector information will be
reverted to factory defaults. Each field will go blank, Alert e-mail service will be set to OFF, Language to English,
$FSUJmDBUJPOTFUUJOHUP0/BOE1BTTXPSETFUUJOHUPBENJO
(1) Click [RESET] in the Setup window.
t 5IFXJOEPXBQQFBSTUPSFTFUUIFOFUXPSLTFUUJOHT
(2) Click [OK] to revert the network settings to factory defaults.
t *GZPVDMJDL<$"/$&->UIFXJOEPXDMPTFTXJUIPVUSFTFUPGUIFOFUXPSLTFUUJOHT
EN-24
8. ProjectorView
8.6. Alert E-mail setting
8.6.1. Alert E-mail function
When there is something wrong with the projector, an E-mail is automatically sent to the designated address to
notify the error status.
To use this function, it is necessary to change the settings in the Alert E-mail Setup window appropriately.
<Note>
Once you have configured the above settings, the E-mail function remains enabled even after you close the web
CSPXTFS1SPKFDUPS7JFX
'VSUIFSNPSFXIFOZPVTFU$0/530-4:45&.JOUIF/&5803,NFOVUP$3&4530/
the ProjectorView becomes disabled, however, the alert E-mail function remains enabled.
An example: Sending an alert message when the lamp change required.
ProjectorView Alert:
5IFMBNQIBTSFBDIFEUIFNBYJNVNVTBHFUJNF
Replace the lamp and reset the lamp counter.
Please see the user manual for detailed instructions.
Projector name : abc
1SPKFDUPSNPEFM9:
Serial number : 12345
*OTUBMMFEEBUF
Installed location : 10Factory-5F
Operation time : 2146 hours, 43 minutes
Lamp time : 4000 hours, 0 minutes
-BTUMBNQSFQMBDFEEBUF
-BTUNBJOUFOBODFEBUF
“Projector model” varies depending on the type of projectors.
EN-25
8. ProjectorView
8.6.2. E-mail setting
(1) Click [SETUP] button in the ProjectorView main window (ALERT E-MAIL).
t "MFSU&NBJM4FUVQXJOEPXJTEJTQMBZFE
<Note>
t #FTVSFUPFOUFSEBUBXJUIJOmWFNJOVUFTBGUFSUIF"MFSU&NBJM4FUVQXJOEPXJTEJTQMBZFE$MJDL0,UPTBWF
changes. The connection will turn off in five minutes after the window is displayed so you need to go back
to the main window (ALERT E-MAIL) to access the Alert E-mail Setup window.
(2) Set each item referring to the explanation described below.
5IFGPMMPXJOHUBCMFFYQMBJOTFBDIJUFN
Regarding the settings, consult your network administrator or check the settings of your E-mail server.
Item
Description
"MFSUFNBJMTFSWJDF
SMTP Server *1
5VSO0/0''UIFTFOEJOHPGBOBMFSU&NBJM
Enter the name of the SMTP server that is used for sending an E-mail. (Designate by
URL or IP address.)
Port *2
Enter the port number of the SMTP server. (Default value: 25)
DNS Server *3
Enter the name of the DNS server when you designate the SMTP server or POP
server using an URL. (Designate by IP address.) For details, consult your network
administrator.
&NBJMBEESFTT4
&OUFSUIFEFTUJOBUJPOBEESFTTPGUIFBMFSU&NBJMFHBENJOJTUSBUPS!YYYYYYYYY
(Up to 64 characters) (Up to 3 addresses can be designated.)
E-mail from *4
&OUFSUIFTPVSDFBEESFTTPGUIFBMFSU&NBJMFH1+7JFX!YYYYYYYYY
Authentication settings
Configure the following settings when you use the SMTP server having the
authentication function.
Authentication method
Select the authentication method for sending an E-mail.
OFF:
No authentication for sending an E-mail.
SMTP-Auth:
To use this method, enter User name, Password, and SMTPAuth method.
POP before SMTP: To use this method, enter User name, Password, POP Server
name, and Port number.
User name *4
(When you select the SMTP authentication) Enter the user name and password
registered on the SMTP server.
Password *4
(When you select the POP before SMTP) Enter the user name and password
registered on the POP server.
SMTP-Auth method
Select the SMTP authentication method.
Plain:
Password is sent to the SMTP server unencrypted.
Login:
Password is sent to the SMTP server unencrypted.
CRAM-MD5: Password is sent encrypted.
POP server *1
Enter the POP server name that is used for the POP before SMTP authentication.
(Designate by URL or IP address.)
Port *2
Enter the port number of the POP server. (Default: 110)
*1 Use only alphanumeric characters and marks (- _ . ˜).
*2 For data entry, use alphanumeric characters.
*3 For data entry, use alphanumeric characters and mark (.).
*4 'PSEBUBFOUSZVTFBMQIBOVNFSJDDIBSBDUFSTBOENBSLT@ ]<>\^' @).
EN-26
8. ProjectorView
8.6.3. Sending test E-mail
After completing the setting on the Alert E-mail Setup window, a test E-mail can be sent to confirm whether the
E-mail is correctly delivered to the destination. When clicking [SEND] on the main window (ALERT E-MAIL), the test
E-mail is sent. Confirm whether the E-mail is correctly delivered to the destination address.
<Note>
t *GUIFUFTU&NBJMJTOPUDPSSFDUMZSFDFJWFEDPOmSNUIFBEESFTTPGUIF&NBJMTFSWFSBOEUIFEFTUJOBUJPOBOE
the connection status of the network. For details, make an inquiry to the network administrator.
t 8IFOBOFSSPSPDDVSTJOUIF-"/GVODUJPOUIFBMFSU&NBJMNBZOPUCFTFOU
EN-27
9. Visual PA2 (Visual PA2 enabled projectors only)
Visual PA2 is a feature to display messages on the projector screen.
It can be used for all active Visual PA2 enabled projectors.
"EEJUJPOBMMZUIFQSPKFDUPSJTDBQBCMFPGSFBEJOHBMPVEPOTDSFFONFTTBHFTVTJOHUIF5FYU4QFFDIGVODUJPO/PUF
that some projectors may not have this function. See your projector User Manual for more information.
<Note>
t 5IJTQSPKFDUPSEPFTOPUTVQQPSUUIF5FYU4QFFDIGVODUJPO
Visual PA2 is not available when using the projectors listed in page 32.
5IJTGFBUVSFPQFSBUFTCZSFGFSFODJOHUIFJOGPSNBUJPOEJTQMBZFEJOUIFQSPKFDUPSMJTU:PVOFFEUPDMJDL<3FGSFTI
Status] to update the list before using this feature.
9.1. Starting Visual PA2
(1) Click [Visual PA2] in the tool bar on the main screen.
t i7JTVBM1"wXJOEPXJTEJTQMBZFE
&OUFSUFYUUPEJTQMBZNFTTBHFT
on the projector screen.
$MJDLUPFYJU7JTVBM1"
Choose the color and font.
:PVDBOBMTPDIPPTFUIFnBTI
UFYUPQUJPO
Choose the color and pattern of
the frame.
Specify the location of
messages. Choose between
)PSJ[POUBMBOE7FSUJDBMBOEUIFO
choose the relative position.
Click to stop displaying
messages.
Click to delete
FOUFSFEUFYUJOUIF
5FYUCPY
$MJDLUPEJTQMBZNFTTBHFTFOUFSFEJOUIF5FYUCPY
$MJDLUPTBWFNFTTBHFTFOUFSFEJO5FYUCPY4FUUJOHTTQFDJmFEGPS
5FYU'SBNF-PDBUJPOBOE5FYU4QFFDIDBOBMTPCFTBWFE
Click to load saved messages.
Select to set Schedule On or Off. When you click Edit, the Visual PA2
Schedule window is displayed. (See page 30.)
(2) Specify Text, Frame, Location, and Text Speech, enter text, and then click [Send].
t "MQIBOVNFSJDBMDIBSBDUFSTTQBDFBOETZNCPMTJODMVEJOHi
!<>DBOCFVTFE
(3) Click [Stop] to stop displaying the message on the projector screen.
<Note>
t *GZPVFYJU7JTVBM1"XIJMFUIFNFTTBHFJTCFJOHEJTQMBZFEPOUIFQSPKFDUPSTDSFFOBDPNNVOJDBUJPOFSSPS
may occur, and an error window may appear. If this happens, restart Visual PA2 and click [Stop].
EN-28
9. Visual PA2 (Visual PA2 enabled projectors only)
9.2. Saving messages entered and settings specified in Visual PA2
:PVDBOTBWFNFTTBHFTFOUFSFEJO5FYUCPYBTXFMMBTTFUUJOHTTQFDJmFEGPS5FYU'SBNF-PDBUJPOBOE5FYU
Speech.
These must be saved before you activate the Schedule function in the Visual PA2 window.
(1) Enter text in Textbox, specify settings for Text, Frame, Location, and Text Speech, and then
click [Save].
t i4BWF%BUBwXJOEPXJTEJTQMBZFE
(2) Enter the Data name in Save Data name and click [Save].
t 6QUPEBUBDBOCFTBWFE
9.3. Loading saved data in Visual PA2
(1) Click [Load].
t i-PBE%BUBwXJOEPXJTEJTQMBZFE
(2) Select the data you want to load and click [Load].
9.4. Deleting data from Visual PA2
(1) Click [Load].
t i-PBE%BUBwXJOEPXJTEJTQMBZFE
(2) Select the data you want to delete and click [Delete].
EN-29
9. Visual PA2 (Visual PA2 enabled projectors only)
9.5. Configuring the Schedule function of Visual PA2
By using the Visual PA2’s Schedule function, your intended messages can be displayed on the screen at a set
time.
(1) Click [Edit] in the Schedule area.
t 7JTVBM1"4DIFEVMFXJOEPXJTEJTQMBZFE5IFXJOEPXCFMPXTIPXTUIFFYBNQMFXIFOUIFTDIFEVMFT
have been entered in three rows.)
Item
Description
Enable
Day
Enables the Schedule function for a particular day or period in each row.
From the pull-down menu, selects the day or period during which the Schedule
GVODUJPOJTFOBCMFE:PVDBOTFMFDUZPVSDIPJDFGSPN4VO.PO5VF8FE5IV
Fri, Sat, Mon-Fri, Mon-Sat, Sat-Sun, and Everyday.)
From the pull-down menu, sets the start time in the Schedule function.
From the pull-down menu, sets time period during which a message is displayed.
From the pull-down menu, selects the message to be displayed on the screen
when the Schedule function is enabled.
(More than one message should be saved in advance. See “9.2. Saving
messages entered and settings specified in Visual PA2” on page 29.)
Clears all entries from the selected row.
4BWFTDIBOHFTBOEDMPTFTUIFXJOEPX
Turn-on Time
Period
Data Name
Clear
&YJU
(2) Configure settings ( through ) and check/uncheck the checkboxes for .
t 6QUPUFOTDIFEVMFTDBOCFDPOmHVSFEVTJOHUIFGPVSSPXTJOUIFUBCMF:PVDBODPOmHVSFBTDIFEVMFGPS
each row.)
t #ZEFGBVMUXIFOOPTDIFEVMFJTFOUFSFEUIFUBCMFIBTPOMZPOFSPX"OFXSPXJTBVUPNBUJDBMMZ
added when you enter the items for , , , and in the first row. In this manner, up to ten rows are
automatically added to the table.
(3) Click [Exit] to close the window.
<Note>
t 0ODFBTDIFEVMFIBTCFFODPOmHVSFEJUJTFYFDVUFEBVUPNBUJDBMMZFWFOJGUIF7JTVBM1"XJOEPXJTOPU
displayed.
t *GZPVTFOENFTTBHFTNBOVBMMZGSPN7JTVBM1"XIFOBTDIFEVMFJTCFJOHFYFDVUFEUIFTFNFTTBHFTIBWF
IJHIFSQSJPSJUZPWFSUIBUTDIFEVMF*OBEEJUJPOXIFOUIFTFUUJOHTPGBTDIFEVMFDVSSFOUMZCFJOHFYFDVUFEBSF
reconfigered, the Visual PA2 window will close automatically.
t .PSFUIBOPOFTDIFEVMFDBOOPUCFDPOmHVSFEBUUIFTBNFUJNFPOUIFTBNFEBZ
t 5IF4DIFEVMF4FUUJOHXJMMCFFYFDVUFEXIJMFi1SPKFDUPS7JFX(MPCBMwJTJOPQFSBUJPO
t %FQFOEJOHPOVTBHFDPOEJUJPOTTVDIBTXIFOUIFSFBSFTPNBOZQSPKFDUPSTUPDPOUSPMUJNFMBQTFTNBZPDDVS
between the start time of Visual PA2 and the start time of a schedule.
t 8IFO/FUXPSL5JNF1SPUPDPM/51
JTVTFEUPBVUPNBUJDBMMZTZODISPOJ[FXJUIBO*OUFSOFUUJNFTFSWFSUIFTUBSU
time of a pre-configured schedule may not match the clock of the projector, and the schedule may not be
FYFDVUFE
t 8IFOUIFBVUPNBUJDUJNFBEKVTUNFOUCZTVNNFSUJNFJTWBMJEUIFTDIFEVMFPQFSBUJPONBZOPUCFFYFDVUFE
because the time is automatically adjusted before and after switching over.
EN-30
10.Telnet setup (Telnet enabled projectors only)
:PVDBOTFUUIFQBTTXPSEGPS1SPKFDUPS7JFXBXFCCBTFESFNPUFDPOUSPMBOENPOJUPSJOHUPPMGPSOFUXPSL
projectors, and the industry standard protocol PJLink based remote projector management tool, the display
language on the ProjectorView, the LAN controlled mode, and the PJLink certification mode by running Telnet on
the projector screen.
Telnet is not available when using other than the projectors listed in page 32. Configure the above settings in
ProjectorView in this case.
<Note>
t #ZEFGBVMU5FMOFUJTEJTBCMFEPO8JOEPXT7JTUBPS8JOEPXT5PFOBCMF5FMOFUHPUP$POUSPM1BOFMBOETFMFDU
<1SPHSBNTBOE'FBUVSFT>*OUIFMFGUDPMVNOTFMFDU<5VSO8JOEPXTGFBUVSFTPOPSPGG>BOEUIFODIFDLUIFCPY
OFYUUPUFMOFU
(1) Select the projector that you want to configure on Telnet from the list of projectors on the
main screen.
t 3VO5FMOFUPOPOFQSPKFDUPSBUBUJNF.VMUJQMFQSPKFDUPSTDBOOPUCFTFUTJNVMUBOFPVTMZ
(2) Click [Telnet] in the toolbar on the main screen.
t "DPNNBOEQSPNQUTUBSUT
t "OFSSPSNFTTBHFBQQFBSTJGUIFTFMFDUFEQSPKFDUPSJTOPU5FMOFUFOBCMFE*GUIJTIBQQFOTDPOmHVSFUIF
projector from ProjectorView.
(3) Press the [Enter] key when the above screen appears.
<Note>
t 1SFTTUIF<&OUFS>LFZXJUIJOmWFTFDPOET*GOPUUIFDPOOFDUJPOJTUFSNJOBUFEBOEUIF<&OUFS>LFZJTOPU
SFDPHOJ[FE*GUIJTIBQQFOTFYJUUIFDPNNBOEQSPNQUBOETUBSUJUBHBJO
(4) Setup menus appear.
For more information on telnet, see the LAN Control Utility manual that comes with the projector.
EN-31
11.Others
11.1. Troubleshooting
t 5IFQSPKFDUPSDBOOPUCFSFDPHOJ[FE
5IFQSPKFDUPSNBZOPUCFSFDPHOJ[FEBVUPNBUJDBMMZEVFUPUIFTFUUJOHPGmSFXBMM*OTVDIDBTFUIF
DPNNVOJDBUJPOPGi1SPKFDUPS7JFX(MPCBMwTIPVMECFSFHJTUFSFEBTBOFYDFQUJPOUPUIFmSFXBMM'PSUIF
setting of the fire wall, see the manual of the software that configures the fire wall.
t 0QFSBUJPOCZUIFSFNPUFDPOUSPMMFSDBOOPUCFQSPQFSMZQFSGPSNFE
The operation may not be performed until the last operation has been completed. In such case, wait for a
while and perform the operation again. In addition, confirm whether the network setting such as IP address is
correct.
t "QQMJDBUJPOCFDPNFTi/PSFQMZw
Since it may take time for processing of the automatic status acquisition, the application can not be operated
during that time, and “No reply” may be displayed. Wait for a while until the processing has been ended.
t "QQMJDBUJPODBOOPUCFPQFSBUFETPNFUJNFT
The application cannot be operated during the acquisition of the projector status. When the main power of the
projector is off or projectors not actually connected are registered, the projector status acquisition may take
longer time to complete because it waits until time out. In this case, you can reduce the acquisition time by
deleting unnecessary registered projectors.
t 1SPKFDUPSTDBOOPUCFDPOUSPMMFE1SPKFDUPSTUBUVTJTOUEJTQMBZFE
3FTUBSUUIFBQQMJDBUJPO*GUIFQSPCMFNQFSTJTUTi*OJUJBMJ[F/FUXPSL$POmHVSBUJPOwPOUIFTFUVQTDSFFOPSUSZ
“7 factory defaults” using a Telnet connection. In that case, you need to make settings of the projector again,
because they are reset to the default values.
11.2. Supported Projectors
t i5FMOFUwJTBWBJMBCMFJOUIFGPMMPXJOHUZQFTPGQSPKFDUPST'PSEFUBJMTTFFi-"/$POUSPM6UJMJUZw6TFS.BOVBM
included with the projector.
t i7JTVBM1"wJTOPUBWBJMBCMFJOUIFGPMMPXJOHUZQFTPGQSPKFDUPST
t *GZPVVTF1SPKFDUPS7JFXJOUIFGPMMPXJOHUZQFTPGQSPKFDUPSTTFFi-"/$POUSPM6UJMJUZw6TFS.BOVBMJODMVEFE
with the projector.
XD2000U, XD1000U, WD2000, XL550U, XL650U, HL650U, WL639U, XL1550U, XL2550U, WL2650U,
HL2750U, MH2850U, FL7000U, WL6700U, XL6600U, XL6500U, FL7000U(BL), FL7000LU, WL6700LU,
XL6600LU, XL6500LU, HD8000, FL6900U, XD3200U, WD3300U, XD3500U, XD221U, XD221U-ST
XD2000U(K), WD2000(K), XL550U(K), XL650U(K), HL650U(K), WL639U(K), XL1550U(K), XL2550U(K),
WL2650U(K), FL7000U(K), WL6700U(K), XL6600U(K), XL6500U(K), XD221U(K)
EN-32
Ver.3.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising