- Computers & electronics
- Computer components
- System components
- Motherboards
- ICOP Technology
- VDX-6372RD
- User manual
advertisement
VDX-6372RD/VDX-6372RD-Plus
DM&P Vortex86DX 600MHz
PC/104 CPU Module
with 2S/2USB/VGA/LCD/GPIO/PWMx16
128MB DDR2 Onboard
User’s Manual
(Revision 1.1A)
Copyright
The information in this manual is subject to change without notice for continuous improvement in the product. All rights are reserved. The manufacturer assumes no responsibility for any inaccuracies that may be contained in this document and makes no commitment to update or to keep current the information contained in this manual.
No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part, in any form or by any means without the prior written permission of the ICOP Technology Inc..
Copyright 2008 ICOP Technology Inc.
Manual No. IUM6372D000-01 Ver.1.0A May, 2010
Manual No. IUM6372D000-01 Ver.1.1A October, 2014
Trademarks Acknowledgment
Vortex86DX is the registered trademark of ICOP Technology Inc.
Other brand names or product names appearing in this document are the properties and registered trademarks of their respective owners. All names mentioned herewith are served for identification purpose only.
T a b l e o f C o n t e n t s
T a b l e o f C o n t e n t s ............................................................. iii
C h a p t e r 1 Introduction……………………………………………1
1.1 Packing List ............................................................ 1
1.2 Product Description ................................................ 1
1.3 Specifications ......................................................... 3
1.4 Board Dimension .................................................... 5
C h a p t e r 2 Installation……………………………………………..6
2.1 Board Outline ......................................................... 6
2.2 Connectors & Jumpers Location .................... ........7
2.3 Connectors & Jumpers Summary ........................... 9
2.4 Pin Assignments & Jumper Settings ..................... 10
2.5 System Mapping ................................................... 19
2.6 Watchdog Timer ................................................... 23
2.7 GPIO .................................................................... 24
2.8 SPI flash ............................................................... 25
2.9 PWM .................................................................... 26
3.0 IDE to SD ............................................................. 27
C h a p t e r 3 Driver Installation……………………………………28
Appendix ………………………………………………………………..29
A. TFT Flat Panel Data Output ...................................... 29
B. TFT Flat Panel Support List ....................................... 30
C. LVDS Flat Panel Support List .................................... 32
D. Flat Panel Hardware Setting ..................................... 33
E. Flat Panel Wiring and Lighting .................................. 34
F. TCP/IP library for DOS real mode .............................. 35
G. BIOS Default Setting ................................................. 36
Warranty ............................................................................................ 37
This page is blank
C h a p t e r 1
Introduction
1.1 Packing List
Product Name
VDX-6372RD
&
VDX-6372RD-Plus
Package
Embedded Vortex86DX CPU All-in-One Board
Manual & Drivers CD x 1
RS232 cable x 2
PRINT cable x1
IDE cable x 1
USB cable x 1
(USB port x 2
)
VGA cable x 1
GPIO cable x 1
PS/2 Mouse cable x 1
PS/2 Keyboard cable x 1
Screw Kit x 1
VDX-6372RD Vortex86DX
PC/104 CPU Module
1
1.2 Product Description
The VDX-6372RD family of low-power x86 embedded controller is designed to meet PC/104 specification, and integrated with the following features.
600 MHz Vortex86DX SoC
VGA, TFT/ LVDS LCD support up to
1280x1024 resolution
128MB DDR2 system memory
Enhanced IDE (UltraDMA-100/66/33)
2 USB 2.0 (host)
Up to 2 serial ports
Parallel port
16-bit GPIOs
PC/104-Plus expansion bus
Meet PC/104 stacking spec.
2 watchdog timer
PWM 16~24 channels
JTAG interface
AMI BIOS
Single voltage +5V DC
Support extended operating temperature range of -20°C to +70°C
The VDX-6372D PC/104 family of embedded controller is designed with backward compatibility in mind, to provide migration path for projects facing end-of-life challenges with their existing x86 based PC/104 controller. The VDX-6372D family of controller is designed as a plug in replacement, with backward compatibility to support legacy software to help extend existing product life cycle without heavy re-engineering.
VDX-6372D is suitable for broad range of data-acquisition, Industrial automation, Process control, Automotive controller, AVL, Intelligent Vehicle management devic,Medical device,
Human machine interface, Robotics, machinery control And more…application that required small footprint, low-power and low-cost hardware with open industry standard such as PC/104.
VDX-6372RD Vortex86DX
PC/104 CPU Module
2
1.3 Specifications
CPU
Features
Cache
BIOS
Bus Interface
System Memory
Watchdog Timer
VDX-6372RD
DM&P SoC CPU Vortex86DX- 600MHz
Real Time Clock with Lithium Battery Backup
L1:16K I-Cache, 16K D-Cache, L2 Cache 128KB
AMI BIOS
PC/104 Standard Compliant (Optional: PCI-104)
128MB DDR2 Onboard
VGA
I /O Interface
Connectors
Flash Disk Support
Software programmable from 30.5 us to 512 seconds x2 sets(Watchdog 1 fully compatible with M6117D)
XGI Volari Z9s Chipset
VGA and TFT Flat Panel Interface Support
LVDS Flat Panel Interface Support (Optional)
Onboard 32MB VGA Memory
Support resolution up to 1280 x 1024,16MB colors
Enhanced IDE port (UltraDMA-100/66/33) x1
RS-232 port x1
RS-232/422/485 port x1 (RS485: Auto Direction)
Parallel port x1
USB port x2 (USB 2.0 version)
16-bit GPIO port x1
2.00 mm
∅
44-pin box header for IDE x1
2.00 mm
∅
44-pin box header for LCD x 1
2.00 mm
∅
10-pin box header for VGA x1
2.00 mm
∅
10-pin box header for USB x1
2.00 mm
∅
26-pin box header for Print x1
2.00 mm
∅
20-pin box header for 16-bit GPIO x1
2.00 mm
∅
10-pin box header for RS-232 x2
2.54 mm
∅
5-pin box header for Keyboard x1
2.54 mm
∅
5-pin header for Mouse x1
2.54 mm
∅
4-pin header for DC-in x1
2.54 mm
∅
3-pin header for RS-485 x1
2.54 mm
∅
2-pin header for Reset x1
2.54 mm
∅
7-pin header for Redundancy x1(Opt)
2.54 mm
∅
2-pin header for SYS-Fail-SW- x1(Opt)
1.25 mm
∅
6-pin Wafer for JTAG x1
44-pin IDE Flash Disk( EmbedDisk 16MB or above)
44-pin IDE to Micro SD (Optional)
VDX-6372RD Vortex86DX
PC/104 CPU Module
3
PWM
Power Requirement
Dimension
Weight
Operating
Temperature
16~24 channels
Single Voltage +5V @ 600mA
90 X 96mm (3.54 x 3.77 inches)
80g
-20 o C ~ +70 o C
-40°C ~ +85°C (Optional)
VDX-6372RD Vortex86DX
PC/104 CPU Module
4
1.4 Board Dimension
VDX-6372RD Vortex86DX
PC/104 CPU Module
5
C h a p t e r 2
Installation
2.1 Board Outline
(Note1: COM2 RS232/422/485 is selected by BIOS setting)
(Note2: PCI-104 connector is optional)
(Note3: VI/O Default setting of PCI-104 connector is +5V)
(Note4: Redundancy Signal and System-Fail-SW are optional)
VDX-6372RD Vortex86DX
PC/104 CPU Module
6
2.2 Connectors & Jumpers Location
Connectors
VDX-6372RD Vortex86DX
PC/104 CPU Module
7
Jumpers & LEDs
VDX-6372RD Vortex86DX
PC/104 CPU Module
8
2.3 Connectors & Jumpers Summary
Summary Table
Nbr
J1
J2
J5
J6
IDE
USB
JTAG
Reset
Description Type of Connections Pin nbrs.
Box Header, 2.0
∅
,22x2
Box Header,2.0
∅
, 5x2
Wafer, 1.25
∅
, 6x1
Pin Header, 2,54
∅
,1x2
44-pin
10-pin
6-pin
2-pin
J7
Redundancy (Optional)
Pin Header, 2.54
∅
, 7x1
J8
System –Fail-Switch (Optional)
Pin Header, 2.54
∅
, 2x1
J9
PS/2 Keyboard
Box Header, 2,54
∅
,1x5
J10 PS/2 Mouse
Pin Header, 2,54
∅
,1x5
J11 COM1(TTL/GPIO-P4 / PWMx8)
Box Header, 2.0
∅
5x2
J12 COM2(RS232/422/485) Box Header, 2.0
∅
5x2
7-pin
2-pin
5-pin
5-pin
10-pin
10-pin
J13 GPIO ( Port 0 / 1 /PWMx16)
Box Header, 2.0
∅
,10x2
J15 RS-485 (Auto direction)
J16 Power Connector
J18 PRINT
J20 PC104 Connector – 64 pin
J21 PC104 Connector – 40 pin
J23 PC/104 + (Optional)
J24 VGA
J25 LCD Connector
Molex Header,2.54
∅
, 3x1
Terminal Block 5.0
∅
,2x1
Box Header, 2.0
∅
, 13x2
Box Header, 2.54
∅
32x2
Box Header, 2.54
∅
20x2
Box Header, 2.0
∅
, 30x4
Box Header, 2.0
∅
,5x2
Box Header,2.0
∅
,22x2
20-pin
3-pin
2-pin
26-pin
64-pin
40-pin
120-pin
10-pin
44-pin
PWR-
Power Active LED (Red)
LED-SMD
LED
IDE-
LED
IDE Active LED (Green )
MTBF-
MTBF-Out (Orange)
LED
LED-SMD
LED-SMD
VDX-6372RD Vortex86DX
PC/104 CPU Module
9
2.4 Pin Assignments & Jumper Settings
J1: IDE (44 Pins)
Pin # Signal Name Pin # Signal Name
1 IDERST 2 GND
3 IDED7 4 IDED8
33
35
37
39
25
27
29
31
41
43
17
19
21
23
5
7
9
11
13
15
IDED6
IDED5
IDED4
IDED3
IDED2
IDED1
IDED0
GND
18
20
IDEREQ 22
IDEIOW 24
6
8
10
12
14
16
IDED9
IDED10
IDED11
IDED12
IDED13
IDED14
IDED15
NC
GND
GND
IDEIOR 26
ICHRDY 28
IDEACK 30
IDEINT 32
GND
GND
GND
NC
IDESA1 34 IDECBLID
IDESA0 36 IDESA2
IDECS-0 38 IDECS1
IDELED 40 GND
VCC
GND
42
44
VCC
NC
J2: USB
Pin # Signal Name Pin # Signal Name
1 VCC 2 VCC
3 LUSBD3- 4 LUSBD2-
5
7
9
LUSBD3+ 6 LUSBD2+
GND 8 GND
GGND 10 GGND
VDX-6372RD Vortex86DX
PC/104 CPU Module
10
J5: JTAG
Pin # Signal Name Pin # Signal Name
1 VCC 2 GND
3
5
TCK
TDI
4
6
TDO
TMS
J6: RESET
Pin # Signal Name Pin # Signal Name
1 RST_SW 2 GND
J7: Redundancy (Optional)
Pin # Signal Name Pin # Signal Name
1 GND 2 SYS-FAIL-OUT
3
5
7
SYS-FAIL-IN
SYS-GPCS-IN
RXD9\
4
6
GPCS0
TXD9\
J8: System-Fail-Switch (Optional)
Pin # Signal Name
1
2
SYS-SW-IN
GND
J9: PS/2 Keyboard
Pin # Signal Name Pin # Signal Name
1
3
5
KBCLK
NC
VCC
2
4
KBDAT
GND
VDX-6372RD Vortex86DX
PC/104 CPU Module
11
J10: PS/2 Mouse
Pin # Signal Name Pin # Signal Name
1
3
5
MSCLK
NC
VCC
2
4
MSDATA
GND
J11: COM 1 (Optional: TTL/ GPIO-P4 / PWMx8)
Pin #
1
3
5
7
9
Signal
Name
DCD1
TXD1
GND
RTS1
RI1
Pin #
2
4
6
8
10
Signal
Name
RXD1
DTR1
DSR1
CTS1
NC
J12: COM2 RS232 / 422 / 485 (Optional: TTL)
Pin # Signal Name Pin # Signal Name
1 DCD2/ 422TX- / RS485- 2 RXD2 / 422TX+ / RS485+
7
9
3
5
TXD2 / 422RX+
GND
RTS2
RI2
4
6
8
10
DTR2 / 422RX-
DSR2
CTS2
NC
VDX-6372RD Vortex86DX
PC/104 CPU Module
12
J13: GPIO (Port 0 / 1/ PWMx16)
Pin # Signal Name Pin # Signal Name
1 GND 2 VCC
3
5
GP00
GP01
4
6
GP10
GP11
7
9
11
GP02
GP03
GP04
8
10
12
GP12
GP13
GP14
13
15
17
19
GP05
GP06
GP07
VCC
14
16
18
20
GP15
GP16
GP17
GND
J15: RS485 (Auto direction)
Pin # Signal Name
1 RS485+
2
3
RS485-
GND
J16: Power Connector (Terminal Block 5.0mm)
Pin # Signal Name
1 +5V
2 GND
J18: PRINT
Pin # Signal Name Pin # Signal Name
1 STB- 14 AFD-
2
3
PD0
PD1
15
16
ERR-
INIT-
4
5
6
PD2
PD3
PD4
17
18
19
SLIN-
GND
GND
VDX-6372RD Vortex86DX
PC/104 CPU Module
13
10
11
12
13
7
8
9
PD5
PD6
PD7
ACK-
BUSY
PE
SLCT
20
21
22
23
24
25
26
GND
GND
GND
GND
GND
GND
NC
J20: PC104 Connector – 64pin
41
43
45
47
49
51
53
55
57
25
27
29
31
33
35
37
39
Pin # Signal Name Pin # Signal Name
1 IOCHCHK * 2 GND
3
5
SD7
SD6
4
6
RESETDRV
VCC
17
19
21
23
7
9
11
13
15
SD5
SD4
SD3
SD2
SD1
SD0
AEN
SA19
8
10
12
14
16
18
IOCHRDY 20
22
24
IRQ9
-5V
DRQ2
-12V
OWS
+12V
GND
SMEMW *
SMEMR *
SA18
SA17
SA16
SA15
SA14
SA13
SA12
SA11
SA10
SA9
SA8
SA7
SA6
SA5
SA4
SA3
SA2
26
28
30
42
44
46
48
32
34
DRQ3
DACK1 *
36 DRQ1
38 REFRESH *
40 SYSCLK
50
52
54
56
58
IOW *
IOR *
DACK3 *
IRQ7
IRQ6
IRQ5
IRQ4
IRQ3
DACK2 *
TC
BALE
VCC
VDX-6372RD Vortex86DX
PC/104 CPU Module
14
59
61
63
SA1
SA0
GND
60
62
64
OSC
GND
GND
J21: PC104 Connector – 40pin
Pin # Signal Name Pin # Signal Name
19
21
23
25
27
29
31
33
35
37
39
7
9
11
13
15
17
1
3
5
GND
MEMCS16 * 4
IOCS16 *
IRQ10
IRQ11
IRQ12
IRQ15
DRQ7
VCC
GND
2
6
8
10
12
14
IRQ14 16
DACK0 * 18
32
34
MASTER * 36
GND 38
40
GND
SBHE *
SA23
SA22
SA21
SA20
SA19
SA18
SA17
DRQ0 20 MEMR *
DACK5 * 22 MEMW *
DRQ5 24
DACK6 * 26
DRQ6 28
DACK7 * 30
SD8
SD9
SD10
SD11
SD12
SD13
SD14
SD15
NC
VDX-6372RD Vortex86DX
PC/104 CPU Module
15
J23: PC/104 + (Optional)
VI/O Default setting: +5V
If you need to use VI/O as +3.3V, please see the page 19.
20
21
22
23
24
25
26
27
28
29
30
Pin #
1
A
GND
B
NC
2 VI/O(+5V) AD02
3 AD05 GND
4
5
6
7
C/BE0#
GND
AD07
AD09
C
+5V
AD01
AD04
GND
AD08
AD11 VI/O(+5V) AD10
AD14 AD13 GND
14
15
16
17
18
19
8
9
+3.3V
SERR#
10
11
12
GND
STOP#
+3.3V
13 FRAME#
GND
AD18
AD21
+3.3V
IDSEL0
AD24
C/BE1#
GND
GND
AD15
NC
PERR# +3.3V
+3.3V LOCK#
TRDY# GND
IRDY#
D
AD00
+5V
AD03
AD06
GND
GND
AD12
+3.3V
PAR
NC
GND
DEVSEL#
+3.3V
AD16
+3.3V
AD20
AD23
+3.3V
AD17
GND
AD22
C/BE2#
GND
AD19
+3.3V
GND IDSEL1 IDSEL2
C/BE3# VI/O(+5V) IDSEL3
GND
AD29
AD26
+5V
AD25
AD28
GND
AD27
+5V
REQ0#
GND
AD30
GND
REQ2#
GND
REQ1#
+5V
GNT1# VI/O(+5V) GNT2#
AD31
VI/O(+5V)
GNT0#
GND
+5V
CLK2
GND
+12V
-12V
CLK0
+5V
INTD#
INTA#
NC
GND
CLK3
+5V
INTB#
NC
CLK1
GND
RST#
INTC#
GND
VDX-6372RD Vortex86DX
PC/104 CPU Module
16
Please remove the 0 ohm (1206 type) of R212 and add 0 ohm (1206 type) on
R213
VDX-6372RD Vortex86DX
PC/104 CPU Module
17
J24: VGA
Pin #
1
3
Signal
Name
R OUT
G OUT
Pin #
2
4
5
7
B OUT
HSYNC
6
8
9 VSYNCD 10
Signal
Name
GND
GND
GND
GND
GND
J25: LCD (DVO) Connector
27
29
31
33
19
21
23
25
35
37
39
41
43
Pin # Signal Name Pin # Signal Name
1 +3.3V 2 +3.3V
3
5
7
9
LG2
LG4
NC
LR0
4
6
8
10
LG3
LG5
NC
LR1
11
13
15
17
LR2
LR4
GND
NC
12
14
16
18
LR3
LR5
NC
NC
NC
NC
LB0
LB2
LB4
NC
LG0
GND
NC
NC
NC
NC
20
22
24
26
28
30
32
34
36
38
40
42
GND
NC
LB1
LB3
LB5
NC
LG1
GND
LCLK
LDE
LHSYNC
LVSYNC
LBACKL 44 LVDDEN
(Please refer to Appendix A, for TFT Flat Panel Data Output)
VDX-6372RD Vortex86DX
PC/104 CPU Module
18
2.5 System Mapping
VDX-6372RD Vortex86DX
PC/104 CPU Module
19
VDX-6372RD Vortex86DX
PC/104 CPU Module
20
VDX-6372RD Vortex86DX
PC/104 CPU Module
21
2.6 Watchdog Timer
There are two watchdog timers in Vortex86SX/DX CPU. One is compatible with M6117D watchdog timer and the other is new. The M6117D compatible watchdog timer is called WDT0 and new one is called WDT1.
We also provide DOS, Linux and WinCE example for your reference. For more technical support, please visit: http://www.dmp.com.tw/tech or download the PDF file: http://www.dmp.com.tw/tech/vortex86dx/
VDX-6372RD Vortex86DX
PC/104 CPU Module
22
2.7 GPIO (General Purpose Input / Output)
40 GPIO pins are provided by the Vortex86SX/DX for general usage in the system. All GPIO pins are independent and can be configured as inputs or outputs, with or without pull-up/pull-down resistors.
We also offer DOS, Linux and WinCE example for your reference. For more technical support, please visit: http://www.dmp.com.tw/tech or download the PDF file: http://www.dmp.com.tw/tech/vortex86dx/
VDX-6372RD Vortex86DX
PC/104 CPU Module
23
2.8 SPI flash (Serial Peripheral Interface)
As SPI Flash
(
Serial Peripheral Interface) offers many benefits including: reduced controller pin count, smaller and simpler PCBs, reduced switching noise, less power consumption, and lower system cost
Many of users may consider using a formatted SPI flash to boot for the system or emulate SPI flash as Floppy (A: Driver or B: Driver). Then you must know how to set for this condition in
CMOS Setup and boot up under DOS 6.22, X-DOS, DR-DOS and Free DOS.
For more technical support, please visit: http://www.dmp.com.tw/tech or download the PDF file: http://www.dmp.com.tw/tech/vortex86dx/
VDX-6372RD Vortex86DX
PC/104 CPU Module
24
2.9 PWM (Pulse-width modulation)
Pulse-width modulation (PWM) of a signal or power source involves the modulation of its duty cycle, to either convey information over a communications channel or control the amount of power sent to a load.
The popular applications of pulse width modulation are in speed control of electric motors, volume control of Class D audio amplifiers or brightness control of light sources and many other power electronics applications.
The Vortex86DX SoC integrated 32 channels of PWM interface enabling the Automation, robotic industry to a New Age x86 SoC platform and we also offer the sample code of PWM which will guide the engineer to control the PWM functionality smoothly.
For more inquire of this sample code that please contact our sales team or mail to: [email protected]
VDX-6372RD Vortex86DX
PC/104 CPU Module
25
3.0 IDE to SD (Micro-SD)
Vortex86DX SoC also built-in simulation circuit to adapt SD to IDE in order to allow your system to recognize Micro-SD card as C: or D: Driver
SD-1917: 44 pins IDE to SD Adapter is an ideal solution for industrial PC or embedded system and 44 pins IDE to SD Adapter can be easily installed on all Vortex86DX-63xx CPU boards. You or your customers just do the BIOS setting and use SD-1917 to connect IDE connector of
Vortex86DX-63xx directly.
For further inquiries of SD-1917, please contact ICOP sales team or mail to: [email protected]
for your request.
<BIOS setting>
Get into the BIOS setup Utility
Choose Primary IDE Pin Select: SD card
Press “F10” to Save configuration changes and exit setup
SD-1917
SD-1917: http://www.icop.com.tw/pddetail.aspx?id=125&pid=4
VDX-6372RD Vortex86DX
PC/104 CPU Module
26
C h a p t e r 3
Driver Installation
VGA
The Vortex86DX processor also use external Display chip ““Volari™ Z9s” which is an ultra low powered graphics chipset with total power consumption at around 1-1.5 W. It is capable in providing VGA display output upto 1600x1200. With DVO interface, developers could easily connect flat Panel to support TFT and LVDS output.
Operating system support
The Vortex86DX-6372RD PC/104 CPU board supports Embedded software: Free DOS, DOS
6.22, PCDOS 7.1, DR-DOS, x-DOS, OS/2, Windows CE 6.0, Windows 98, Windows XP
Professional, Windows Embedded standard (XPE) and Windows 2000 (SP4).
Please get the drivers from the Driver CD which attached with the standard packing of
Vortex86DX-6372RD board or please get it from DMP official website: http://www.dmp.com.tw/tech/vortex86dx/
Vortex86DX-6372RD also supports most of the popular Linux distributions, for more detail information, please visit DMP official website: http://www.dmp.com.tw/tech/vortex86dx/
VDX-6372RD Vortex86DX
PC/104 CPU Module
27
Appendix
A. TFT Flat Panel Data Output
VDX-6372RD Vortex86DX
PC/104 CPU Module
28
B. TFT Flat Panel Support List
Size Brand Resolution
5.7” Data image 320x240
5.7” Optrex 320x240
5.7” TOSHIBA 320x240
5.7” Sharp 320x240 (QVGA / VGA)
5.7” Kyocera 320x240 (QVGA / VGA)
5.7” PVI 320x240 (QVGA / VGA)
5.7” Data image 640x480
5.7” Ampire 640x480
5.7” URT 640x480
5.7” Sharp 640x480
5.7” CPT 640x480
6.4” PVI 640x480
6.4” LG-PHILIPS 640x480
6.4” PVI 640x480
6.4” Sharp 640x480
7” AUO 800x480
7” Data image 800x480
7” LG-PHILIPS 800x480 (TFT 24 bits)
7” HITACHI 800x480
7” Samsung 800x480
7” PVI 800x480
7” URT 800x480
7” CHI HSIN 800x480
Model No.
FG050701DSSWBG01
55264GD057J-FW-ABN
LTA057A343F
LQ057Q3DC02
TCG057QV1AC-G10
PD057VU4 /U5
FG050710DSSWJG01/DG01
AM-640480GTMQW-T00H
UMSH-8004MD-T
LQ057V3DG01
CLAA057VA01
V16C6448AC
LB064V02
PD064VT2 /VT4 /VT5
LQ064V3DG01
C070VW02V0
FG0700A0DSSWBG01
LB070WV1
TX18D57VM2BAA
LMS700KF05
PM070WL4
UMSH-8173MD-1T
LW700AT9309
8” Sharp 640x480 LQ080V3DG01
VDX-6372RD Vortex86DX
PC/104 CPU Module
29
Brand
AUO
Sharp
PVI
NEC
NEC
NEC
Sharp
Sharp
Sharp
NEC
Size
8”
8.4”
10.4”
10.4”
10.4”
10.4”
10.4”
10.4”
11”
12.1”
Resolution
800x600 (TFT 24bits)
800x600
640x480
640x480
640x480
640x480
640x480
640x480
800x480
800x600
VDX-6372RD Vortex86DX
PC/104 CPU Module
Model No.
A080SN01 V0
LQ084S3DG01
PD104VT1/VT2
NL6448AC33-18
NL6448AC33-29
NL6448BC33-59
LQ104V1DG51/DG61
LQ10d368
LQ110Y3DG01
NL8060BC31-01
30
C. LVDS Flat Panel Support List
If you would like to use LVDS Flat Panel with Vortex86SX / Vortex86DX series, please contact our regional sales to get ICOP-0096 information or visit ICOP website: http://www.icop.com.tw/pddetail.aspx?id=65&pid=4
ICOP–0096
: 18-bit TFT to LVDS converter and Cable-LVDS-30: LVDS Cable 30cm
Size
Approved LVDS Flat Panel List
Brand Resolution Model No.
3.5” PVI 640x480 PD035VL1
5”
6.5”
8.4”
8.9”
8.9”
10.4”
12.1”
15”
PVI
AUO
AUO
AUO
CPT
AUO
AUO
AUO
640x480
640x480
800x600
1024x600
1024x600
800x600
800x600
1024x768
PD050VL1
G065VN01
G084SN03
A089SW01
CLAA089NA0ACW
G104SN02
G121SN01
G150XG01
VDX-6372RD Vortex86DX
PC/104 CPU Module
31
D. Flat Panel Wiring and Lighting
Hardware
Before you connect the TFT LCD Flat Panel with Vortex86DX-6372RD, please make sure the input Voltage of LCD is +3.3V or Not
BIOS
Please contact or e-mail our regional sales to get the special BIOS for the any TFT LCD
Flat Panels.
Wiring LCD Cable
Please refer to Page 19 ( J25: LCD connector ) and Page 29~34 . For more LCD lighting and integration service, please contact our regional sales or mail to [email protected]
if you have any questions.
VDX-6372RD Vortex86DX
PC/104 CPU Module
32
E. TCP/IP library for DOS real mode
DSock is a TCP/IP library for DOS real mode, which is used by RSIP. It provides simple C functions for programmer to write Internet applications. ICOP also provide Internet examples using DSock: BOOTP/DHCP, FTP server, SMTP client/server, HTTP server, TELNET server,
Talk client/server, etc.
DSock provides a lot of example source code. Programmer can add Internet functions to their project easily and save development time. With a utility "MakeROM”, programmer also can make a ROM image to fit their application, those examples can be seen in the following Application systems: Mity-Mite Serial Server, Web Camera Tiny Server and RSIP Serial Server.
DSock is free for All ICOP products using M6117D/Vortex86/Vortex86SX/Vortex86DX CPU and
ICOP also provide the business version of DSock for those customers who are using other x86
CPUs.
If you would like to use DSock or business version of DSock, Please mail to [email protected]
or contact your regional sales.
Please download the trial DSock software and Utilities from our website: http://www.dmp.com.tw/tech/dmp-lib/dsock/
VDX-6372RD Vortex86DX
PC/104 CPU Module
33
F. BIOS Default setting
If the system cannot be booted after BIOS changes are made, Please follow below procedures in order to restore the CMOS as default setting.
Press “End” Key, when the power on
Press <Del> to enter the AMI BIOS setup
Press “F9” to Load Optimized Defaults
Press “F10” to Save configuration changes and exit setup
VDX-6372RD Vortex86DX
PC/104 CPU Module
34
Warranty
This product is warranted to be in good working order for a period of one year from the date of purchase. Should this product fail to be in good working order at any time during this period, we will, at our option, replace or repair it at no additional charge except as set forth in the following terms. This warranty does not apply to products damaged by misuse, modifications, accident or disaster. Vendor assumes no liability for any damages, lost profits, lost savings or any other incidental or consequential damage resulting from the use, misuse of, originality to use this product. Vendor will not be liable for any claim made by any other related party. Return authorization must be obtained from the vendor before returned merchandise will be accepted.
Authorization can be obtained by calling or faxing the vendor and requesting a Return
Merchandise Authorization (RMA) number. Returned goods should always be accompanied by a clear problem description.
VDX-6372RD Vortex86DX
PC/104 CPU Module
35
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement