ZIS420NH - PC Richard

ZIS420NH - PC Richard
Installation
Instructions
Side by Side Refrigerators
Design Guide
With Installation Instructions
31-49057-1
224D1889P015
10-14 GE
monogram.com
Safety Information
BEFORE YOU BEGIN
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
Skill Level – Installation of this refrigerator requires
basic mechanical, carpentry and plumbing skills.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not
covered under the GE Appliance Warranty.
See the Owner’s Manual for warranty information.
Read these instructions completely and carefully.
•
– Save these instructions for
local inspector’s use. Observe all governing codes
and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions with
your Owner’s Manual for future reference.
IMPORTANT
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These
words are defined as:
DANGER
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
WARNING
Electrical Shock Hazard.
Plug into a grounded 3-prong outlet.
Do not remove the ground prong.
Do not use an adapter.
Immediately replace electric cords that become frayed
or damaged.
WARNING
Do not use an extension cord with this appliance.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Follow the instructions in the section Grounding the
Refrigerator.
Tip Over Hazard.
These refrigerators are top heavy, especially with any doors open, and must be secured to prevent tipping
forward which could result in death or serious injury. Read and follow the entire installation instructions for
securing the refrigerator with the anti-tip system.
WARNING
Explosion Hazard.
Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can result in
fire, explosion, or death.
WARNING To reduce the risk associated with choking, do not allow children under 3 years of age to have
access to small parts during the installation of this product.
CAUTION
Lifting Hazard
This refrigerator is very heavy. To reduce the risk of person injury during maneuvering and installing this
refrigerator, 3 people are required for proper installation of 36” wide model and 4 people are required for proper
installation of a 42” or 48” wide model.
For Monogram local service in your area, call 1.800.444.1845.
For Monogram service in Canada, call 1.800.561.3344
For Monogram Parts and Accessories, call 1.800.626.2002.
www.monogram.com
2
Consignes de Sécurité
Ce symbole représente une alerte de sécurité. Ce symbole vous avise de dangers possibles pouvant causer la mort, des
blessures ou autres. Tous les messages de sécurité seront précédés du symbole d’alerte de sécurité ainsi que des mots «
DANGER », « AVERTISSEMENT » ou « MISE EN GARDE ». Ces messages sont les suivants :
DANGER
Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, entraînera des bles
sures graves, voire la mort.
AVERTISSEMENT
Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, peut entraîner des
blessures graves, voire la mort. .
Signale une situation qui présente un danger imminent et qui, si elle n’est pas évitée, peut entraîner des
ATTENTION blessures mineures ou graves.
AVERTISSEMENT
Risque de choc électrique.
Branchez l’appareil dans une prise triple avec terre.
Ne retirez pas la broche de terre.
N’utilisez pas d’adaptateur.
Le non-respect de ces instructions peut entraîner des
risques d’incendies, des chocs électriques ou la mort.
Remplacer immédiatement tout cordon électrique
effiloché ou endommagé.
AVERTISSEMENT
N’utilisez pas de rallonge avec cet appareil.
Le non-respect de ces instructions peut entraîner des
risques d’incendies, des chocs électriques ou la mort.
Suivez les instructions de la section Mise à la terre du
réfrigérateur.
Risque de basculement
Ces réfrigérateurs présentent une partie supérieure lourde, en particulier avec une porte ouverte; ils doivent donc
être fixés pour prévenir le basculement vers l’avant et le risque concomitant de blessure grave ou fatale. Lisez et
suivez les instructions d’installation complètes pour l’installation du système anti-basculement.
AVERTISSEMENT
Risque d’explosion.
Conservez les matériaux et vapeurs inflammables tels que l’essence à l’écart de votre réfrigérateur. Le nonrespect de cette instruction peut entraîner un risque d’incendie, d’explosion ou de décès.
Pour réduire le risque d’étouffement pendant l’installation de ce produit, ne pas laisser les
petites pièces à la portée des enfants âgés de moins de 3 ans.
AVERTISSEMENT
ATTENTION Risque associé à la manutention d’une charge lourde
Ce réfrigérateur est très lourd. Pour réduire le risque de blessure lors de la manutention de ce réfrigérateur, trois
(3) personnes sont nécessaires pour procéder à l’installation appropriée du modèle 36 pouces, quatre (4) pour
l’installation des modèles 42 ou 48 pouces.
3
Contents
Safety
Step 4. Household Water Filtration
Step 5. Install Side Panels
Step 6. Install Case Trim
Step 7. Anti-Tip Procedure
Step 8. Level Refrigerator
Step 9. Secure Refrigerator to Cabinetry
Step 10. Adjust Door Swing
Step 11. Remove Door Trim
Step 12. Layout Decorative Door Panels
Step 13. Attach Brackets to Panels
Step 14. Hang Decorative Door Panels
Step 15. Layout Decorative Hood Panel
Step 16. Install Hood Panel
Step 17. Adjust Decorative Panels
Step 18 Replace Trim
Step 19. Connect Water Supply
Step 20. Connect Power, Close Grille Panel
Step 21. Start Icemaker
Step 22. Install Toekick
Inspect Final Installation
2, 3
Planning Guide
The Installation Space
Dimensions and Clearances
Customization Basics
3/4” Overlay Panel Dimensions - Flush
1/4” Framed Panel Dimensions - Standard
3/4” Overlay Panel Dimensions - Standard
90° Door Swing
130° Door Swing
Dispenser Trim
Side Panels
5
5
6
7
8
9
10
11
12
13
Installation Instructions
Tools, Hardware, Materials
Parts Identification
Grounding the Refrigerator
Step 1. Remove Packaging
Step 2. Move Refrigerator into House
Step 3. Install Water Line
13
14
15
16
16
16
4
17
17
17
17-18
18
18
19
19
20-21
21
22
23
23
24-25
25
26
26
26
27
27
Design Guide
THE INSTALLATION SPACE
DIMENSIONS AND CLEARANCES
36" Models 12"
42" Models 18"
48" Models 20"
25-3/8" Framed Models
25-3/4" Stainless Steel Models
35", 41", or 47"
Case Width
* Shipping height.
The refrigerator can
be adjusted to fit
into a cutout that
is 84-1/2” in height.
*84"
Use leveling legs
From
and wheels for a
Floor
maximum 1” height
adjustment.
*Finished Width
84 1/2" max
Finished
Opening
6"
Electrical
Area
5"
24"
5" Water Supply 5"
*83-1/2"
at
Rear
75" From Floor
to Bottom
of Electrical
Area
3 1/2"
36", 42" or 48"
Frame to Frame
3 1/2"
*For standard installation, the finished cutout width
must be:
35-1/2” for 36” models
41-1/2” for 42” models
47-1/2” for 48” models
Depth Including Handles:
27-3/4" Stainless Steel Models
28-11/16" Professional Models
Product Clearances
These refrigerators are
equipped with a 3-position
door stop. The factory-set
115° door swing can be
adjusted to 90° if clearance
to adjacent cabinets or
walls is restricted. Only
standard installation can be
adjusted to 130°.
*For flush mount installation, the finished cutout width
must be:
39” for 36” models
45” for 42” models
51” for 48” models
Water And Electrical Locations
The opening must be prepared with the electrical
and the cold water supply located as shown.
115° Door Swing
90° Door Swing
130° Door Swing
B
A
The Cutout Depth Must Be 24” For Standard Installation
The refrigerator will project forward, slightly beyond
adjacent cabinetry for standard installation.
B
A
23-7/8"
Behind
Frame
The Cutout Depth Must Be 26-3/16” For Flush Installation
Wooden cleats are required for flush installation. See Side
Cleats on page 13.
C
Additional Specifications
• A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install
a properly grounded 3-prong electrical receptacle
recessed into the back wall. Electrical must be located
on the rear wall as shown.
NOTE: GFI (ground fault interrupter) is not recommended.
• The water line can enter the opening through the floor
or back wall. The water line should be 1/4” O.D. copper
tubing or GE SmartConnect™ kit between the cold
water line and water connection location, long enough
to extend to the front of the refrigerator. Installation of
an easily accessible shut-off valve in the water line is
required.
Models
36”
42”
48”
A
13”
13”
15”
B
15”
19”
20”
C
20-5/8”
26-5/8”
28-5/8”
*Min. Distance
to Wall
*4” Stainless and
Trimmed Models.
5” Pro Series
Allow minimum clearances for the freezer door
(Dimension A) and fresh food door (Dimension B) for a
full 130° door swing and to allow for pan removal.
For a 90° door swing, allow 4” min. clearance to a wall,
for framed and stainless steel models. Allow 5” min.
clearance for professional series models. If the 90° door
stop position is used, pan access is maintained, but pan
removal is restricted.
See the illustrations on pages 6 and 7 to determine door
swing interaction with adjacent cabinets or countertops.
5
Design Guide
CUSTOMIZATION BASICS:
Professional Style Stainless Steel Refrigerators
Stainless steel wrapped refrigerators have beveled edges and professional-style handles. These models are shipped ready
for installation.
Stainless Steel Wrapped Refrigerators
Stainless Steel wrapped refrigerators have wrapped doors and grille panel, beveled edges, and tubular stainless steel
handles that coordinate with other Monogram appliances. These models are shipped ready for installation.
Trimmed Refrigerators
Trimmed refrigerators are designed to be customized with decorative panels. Field installed custom door and grille panels
are required.
Optional Accessory Kits
ZKHSS2: Monogram Tubular Stainless Steel handles
designed to fit 3/4” overlay panels.
ZTK36SSH: Trim Kit for 36” Side-by-side refrigerator using
custom panels for standard installation.
ZKHPSS1: Professional Tubular Stainless Steel handles
designed to fit 3/4” overlay panels. Kit includes one
handle. Order 2 kits for side-by-side refrigerator models
from your Monogram supplier
ZTK42SSH: Trim kit for 42” Side-by-side refrigerator using
custom panels for standard installation.
ZTK48SSH: Trim kit for 48” Side-by-side refrigerator using
custom panels for standard installation.
CUSTOM HANDLE DESIGN GUIDE
(Flush Installation Only)
1-1/4”
For custom handle installation, counterbore holes in rear
of decorative panels may not exceed 1/4” depth to ensure
1/2” material thickness remains for handle support.
NOTE: The counterbore must not exceed 1” in diameter.
Minimum distance from handle
side edge to handle center
should be 1-1/4” as shown.
1/2”
1/4”
3/4”
6
1-1/4”
Design Guide
3/4” OVERLAY PANEL DIMENSIONS
(Flush Installation Only)
IMPORTANT NOTE – DISPENSER MODELS
The refrigerator is supplied with matching adjustable
dispenser trims. The overlay dispenser trim is designed to fit
a total panel thickness of 3/4” plus up to 1/8” adjustability.
• If the panel is less than 3/4” a noticeable gap may be
created around the dispenser trim.
• If the panel is more than 3/4” and fully adjusted away
from door face, the dispenser trim cannot be secured to
the door.
For a more custom appearance, overlay panels may be
installed to give a flush appearance with surrounding
cabinets. The overlay panel must be 3/4” thick. Panel
attaches to included brackets to provide mounting to the
appliance door.
NOTE: We recommend that decorative panels have inside
corners and edges rounded or beveled by cabinet maker to
avoid sharp edges on the panels. Edges to be treated should
include the top, bottom and hinge side edges.
Grille Panel
Dispenser
Cutout
IMPORTANT NOTE: Maximum total weight for the assembled
panels:
• Fresh food door panel – 75 lbs.
• Freezer door panel – 53 lbs.
15-3/8" • Grille Panel – 18 lbs.
Dispenser Cutout
A
B
F
Dispenser
Cutout
Position
9-5/8"
C
G
Freezer
Panel
Fresh
Food
Panel
D
E
1-1/4”
Refrigerator
A
B
C
D
E
F
G
36” Side-by-Side
(in inches)
38”
10-5/8” 68-13/16”
16-7/8”
20-7/8”
18”
3-7/16”
42” Side-by-Side
(in inches)
44”
10-5/8” 68-13/16”
16-7/8”
26-7/8”
18”
3-7/16”
48” Side-by-Side
(in inches)
50”
10-5/8” 68-13/16”
20-7/8”
28-7/8”
18”
5-7/16”
1”
WARNING
1/2”
Top/Bottom Hinge Clearance
Router 1/8” Deep
1/2”
1-1/4”
1”
7
Door Trim Pinch Point Hazard
Improper installation can lead to a finger pinch
point hazard between the side door trim and the
cabinets when operating the door, especially
with children. To minimize this risk you must
follow the installation instructions for cabinet
dimensions, trim assembly, and door stop angle.
Design Guide
1/4” FRAMED PANEL DIMENSIONS
(Standard Installation Only)
5/16"
Trim
Reveal
Door
If you choose to install framed panels, they must
be cut to the dimensions shown. The panels will slide
into the frame on the door and grille.
1/4"
Panel
Non-Dispenser Models
If the custom panel is less than 1/4” thick and it fits
loosely in the door frame it can be backed up with
a piece of filler material or foam tape to improve
the fit.
IMPORTANT NOTE: Maximum total panel weight:
• Fresh food door panel – 75 lbs.
• Freezer door panel – 53 lbs.
• Grille Panel – 18 lbs.
IMPORTANT NOTE – DISPENSER MODELS
The refrigerator is supplied with two dispenser trims,
one for framed panels and one for overlay panels.
• If the panel is less than 0.250” thick, a noticeable gap
may be created around the dispenser trim. Foam
tape may be applied on the door to improve the fit.
• If the panel is more than 0.250” thick, the dispenser
trim cannot be secured to the door.
See Dispenser Trim Fit Example, page 12.
Dispenser Cutout
A
Grille Panel
The framed panel must be 1/4” nominal
thickness to fit the dispenser trim.
B
15-3/8"
Dispenser
Cutout
F
9-5/8"
C
G
Freezer
Panel
Fresh
Food
Panel
D
E
Side-by-Side (in inches)
A
36” Models
33-7/8
42” Models
39-7/8
48” Models
45-7/8
Dispenser
Cutout Position
B
9
9-1/2
9-1/2
8
C
68-3/8
68-3/8
68-3/8
D
14-9/16
14-9/16
18-9/16
E
18-9/16
24-9/16
26-9/16
F
17-13/16
17-13/16
17-13/16
G
3-1/8
3-1/8
5-1/8
Design Guide
3/4” OVERLAY PANEL DIMENSIONS
(Standard Installation Only)
Overlay Panel
Door
For a more custom appearance, overlay panels may
be installed on trimmed models. The overlay panel must
be secured to a 1/4” thick backer panel which slides
into the trim. A spacer panel 0.10” thick must be placed
between the overlay and backer panel.
Assemble the panels with glue and screws:
• Center the spacer panel on the backer panel, left to
right and top to bottom. Secure the panels with glue.
• Center the spacer and backer panel on the overlay
panel and secure with glue and screws. Screws must
be countersunk into the backer panel.
3/4"
Overlay
Panel
Spacer Panel
Backer Panel
NOTE: Left-to-right offset is
not always equal to top-to1/4"
bottom offset.
.10"
Backer
Spacer
Panel
.250” + .10” + .750” = 1.100” Total Panel Thickness
IMPORTANT NOTE – DISPENSER MODELS
The refrigerator is supplied with two dispenser trims,
one for framed panels and one for overlay panels. The
overlay dispenser trim is designed to fit a total panel
thickness of 1.100”.
• If the panel is less than 1.100” a noticeable gap may
be created around the dispenser trim.
• If the panel is more than 1.100” the dispenser trim
cannot be secured to the door.
• The overlay panel must be constructed according to
the specifications shown to achieve the correct total
thickness.
• Alternative panel construction methods such as
securing a 3/4” panel to a 1/4” backer panel cannot
be used. Another method, routing a 3/4” thick panel
on all sides, cannot be used. These methods will not
result in the required 1.100” panel thickness.
See Dispenser Trim Fit Example, page 12.
Dispenser Cutout
A
Grille Panel
Dispenser
Cutout
B
*Cut the dispenser opening after the backer, spacer and overlay
panels have been assembled.
IMPORTANT NOTE: Maximum total weight for the assembled
panels:
15-3/8"
• Fresh food door panel – 75 lbs.
• Freezer door panel – 53 lbs.
• Grille Panel – 18 lbs.
F
*Dispenser
Cutout Position
9-5/8"
C
G
Freezer
Panel
D
Fresh
Food
Panel
E
36” Side-by-Side (in inches)
A
1/4” Backer Panel
33-7/8
.10” Spacer Panel
33
3/4” Overlay Panel 34-1/8
B
9
8-3/8
9-1/4
C
68-3/8
67
68-5/8
D
14-9/16
13-1/4
14-13/16
E
F
18-9/16
17-1/4
18-13/16 17-15/16
G
42” Side-by-Side (in inches)
A
1/4” Backer Panel
39-7/8
.10” Spacer Panel
39
3/4” Overlay Panel 40-1/8
B
9-1/2
8-5/8
9-3/4
C
68-3/8
67
68-5/8
D
14-9/16
13-1/4
14-13/16
E
F
24-9/16
23-1/4
24-13/16 17-15/16
G
48” Side-by-Side (in inches)
A
1/4” Backer Panel
45-7/8
.10” Spacer Panel
45
3/4” Overlay Panel 46-1/8
B
9-1/2
8-5/8
9-3/4
C
68-3/8
67
68-5/8
D
18-9/16
17-1/4
18-13/16
E
F
26-9/16
25-1/4
26-13/16 17-15/16
G
9
3-1/4
3-1/4
5-1/4
Design Guide
Frameless Cabinets:
The case trim overlaps
cabinets at the top
and sides. Therefore,
frameless cabinets may
require filler strips to
prevent interference
with cabinet door swing.
The opening must allow
for filler strips.
Refrigerator
Case Trim
23-7/8"
From Rear of
Refrigerator
1/4"
1/2"
3/4"
1"
1-1/4"
1-1/2"
Stainless Steel
Top View
90° DOOR SWING
(Standard Installation
Only)
Scale 1:1
Door
IMPORTANT NOTE –
FOR DISPENSER MODELS:
Dispenser models are supplied
with two dispenser trims, one to fit
framed panels and one for overlay
panels. Dispenser trim fit to the
custom panel depends on correct
panel thickness. Framed panels
must be 1/4” nominal. Overlay
panels should be constructed as
shown to accomplish a total 1.100”
thickness. See pages 9 and 10 for
details.
3/4" Overlay
Panel
(Nominal Size)
1/4"
1/2"
3/4"
1"
1-1/4"
10
Design Guide
Refrigerator
Frameless Cabinets: The case trim overlaps
cabinets at the top and sides. Therefore,
frameless cabinets may require filler strips
to prevent interfeence with cabinet door
swing. The opening must allow for filler strips.
23-7/8" From
Rear of
Refrigerator
Case
Trim
3/4"
1"
1-3/4"
2"
1-1/2"
1/2"
3"
2-1/2"
1-1/4"
1/4"
2-3/4"
2-1/4"
1/4"
1/2"
3/4"
1"
l
tee
sS
les
ain
St
3/4" Overlay
Panel
(Nominal Size)
Door
1/4"
Top View
130° DOOR SWING
(Standard Installation Only)
Scale 1:1
IMPORTANT NOTE –
FOR DISPENSER MODELS:
Dispenser models are supplied with two
dispenser trims, one to fit framed panels
and one for overlay panels. Dispenser trim
fit to the custom panel depends on correct
panel thickness. Framed panels must be
1/4” nominal. Overlay panels should be
constructed as shown to accomplish a total
1.100” thickness. See pages 9 and 10 for
details.
11
1/2"
3/4"
1"
1-1/4"
Design Guide
DISPENSER TRIM FIT EXAMPLES:
(NOT TO SCALE)
3/4” OVERLAY PANEL
(Flush Installation Only)
• The dispenser trim fits over the
custom panel and snaps into the
freezer door.
1/4” FRAMED PANEL
(Standard Installation
Only)
• The dispenser trim fits over the
custom panel and snaps into the
freezer door.
• The clips will not engage the door
if the panel is more than 0.250” thick.
• If the panel is less than 0.250” thick,
a noticeable gap may be created
around the dispenser trim.
3/4” OVERLAY PANEL
(Standard Installation
Only)
• The dispenser trim fits over the
custom panel and snaps into the
freezer door.
• The clips will not engage the door
if the panel is more than 1.100” thick.
• If the panel is less than 1.100” thick,
a noticeable gap may be created
around the dispenser trim.
12
Installation Instruction
24"
SIDE PANELS
Side panels must be used
whenever the sides of the
refrigerator will be exposed.
The 1/4” side panels will
slip into the side case trim.
Secure the panels to the
refrigerator with stick-on
*84"
hook and loop fastener
strips. Order the side
panels from the cabinet
manufacturer.
• Cut a notch in the top
front corner as shown
to allow clearance for
corner keys in the front
side trim.
TOOLS AND MATERIALS REQUIRED
• Tinsnips to cut banding
• Stepladder
• 1” Bit extension
• Tape measure
• Gloves
• 1/4” Drywall screws
• 5-Gal. Bucket with cover
• 6” Spirit level
• Appliance hand truck
• Tubing cutter
• 7/16” open-end wrench
• #2 Phillips screwdriver
• Drill and appropriate bits
• 5/16”, 7/16” socket
• Safety glasses
• 1-1/8” open end wrench
• Pliers
• 1/4”, 5/16” Combo Rachet
• 35” long 2x4 for Anti-Tip support
• 1/4” copper water line tubing or GE SmartConnect™
Refrigerator Tubing kits
• Water shut-off valve
• Custom panels for doors and grille panel
• Screws to secure refrigerator to cabinetry
• Stick-on hook and loop fastener strips for
1/4” side panels
3/16"
1-7/8"
*3" to 4"
2-9/16"
* Depending on installation height.
SIDE CLEATS
(Flush Installation Only)
Wood cleats are required to be installed vertically
down both sides of the cabinet opening to provide
depth stop for the refrigerator when installed into the
opening.
The front of the cleat should be installed 5-1/4” from
the front of the cabinet opening.
HARDWARE SUPPLIED
• Water filter bypass plug
• Toekick
• 1/4” nut and ferrule
• Dispenser trim for overlay panels (for use with
Custom Panel models).
• Flush inset panel bracket kit
• Case trim package
TOP VIEW
Finished
Cleat
5-1/4”
DOOR
3/4” Panel
1/2”
Case Trim
13
Installation Instruction
PARTS IDENTIFICATION:
Panel Bracket,
Top Right
Trim, Freezer
Bottom
Panel Bracket,
Bottom Left
Trim, Handle
Side Visor,
Fresh Food
Trim, Handle
Side Visor,
Freezer
Panel Bracket,
Bottom Right
Trim, Fresh
Food Handle
Side Cover
Trim, Fresh
Food Hinge
Side
Trim, Freezer
Handle Side
Cover
Panel Bracket,
Top Left
Panel Bracket,
Top (2)
Trim, Case,
RH Side
Trim, Fresh
Food Top
Panel Bracket,
Bottom (2)
Trim, Fresh
Food Bottom
Door Bracket
(4);
Installed on
door
Drill holes at top of freezer panel.
Fresh Food
Panel Template
Trim, Freezer
Hinge Side
Drill holes at bottom of freezer panel.
Drill holes at top of fresh food panel.
Freezer Panel
Template
Drill holes at bottom of fresh food panel.
Hood Template
Trim, Freezer
Top
14
Trim, Case,
LH Side
Installation Instruction
FLOORING
MISE À LA TERRE DU RÉFRIGÉRATEUR
For proper installation, this refrigerator must be placed
on a level surface of hard material that is at the same
height as the rest of the flooring. This surface should
be strong enough to support a fully loaded refrigerator,
or approximately 1,500 lbs.
NOTE: Protect the finish of the flooring. Cut a large
section of the cardboard carton and place under
the refrigerator where you are working.
AVERTISSEMENT
REFRIGERATOR LOCATION
• Do not install the refrigerator where the
temperature will go below 55°F (13°C). It will
not run often enough to maintain proper
temperatures.
• Do not install the refrigerator where
temperatures will go above 100°F (37°C). It will
not perform properly.
• Do not install the refrigerator in a location
exposed to water (rain, etc.) or direct sunlight.
• Install it on a floor strong enough to support it
fully loaded.
GROUNDING THE REFRIGERATOR
WARNING
Risque de choc électrique.
Le non-respect de ces instructions peut entraîner des
risques d’incendies, des chocs électriques ou la mort.
Le cordon d’alimentation de cet appareil est équipé
d’une fiche à trois broches (pour une mise à la terre)
qui s’adapte à la prise de courant standard à 3
broches (pour une mise à la terre) pour minimiser les
risques de chocs électriques par cet appareil.
Faites vérifier la prise murale et le circuit électrique par
un électricien qualifié pour s’assurer que le système est
correctement mis à la terre.
Dans le cas d’une prise biphasée, l’installateur a la
responsabilité et l’obligation de la remplacer par une
prise triphasée correctement mise à la terre.
NE COUPEZ PAS OU N’ENLEVEZ
PAS, SOUS AUCUN PRÉTEXTE,
LA TROISIÈME BROCHE DE
MISE À LA TERRE DU CORDON
D’ALIMENTATION.
N’UTILISEZ PAS D’ADAPTATEUR
POUR BRANCHER LE
RÉFRIGÉRATEUR À UNE PRISE BIPHASÉE.
N’UTILISEZ PAS DE RALLONGE AVEC CET APPAREIL.
Electrical Shock Hazard.
Failure to follow these instructions can result in death,
fire, or electrical shock.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall receptacle
to minimize the possibility of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly
grounded.
Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to have
it replaced with a properly grounded 3-prong wall
outlet.
DO NOT, UNDER ANY
CIRCUMSTANCES, CUT OR
REMOVE THE THIRD (GROUND)
PRONG FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT
THE REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.
15
Installation Instructions
STEP 1 REMOVE PACKAGING
WARNING
STEP 3 INSTALL WATER LINE
• A cold water supply is required for automatic icemaker
operation. The water pressure must be between 40 and
120 p.s.i.
• Route 1/4” OD copper or GE SmartConnect™ plastic
tubing between house cold water line and the water
connection location.
• The tubing should be long enough to extend to the
front of the refrigerator. Allow enough tubing to
accommodate the bend leading into the water line
connection.
Tip Over Hazard.
The refrigerator is much heavier at the top than at the
ERWWRP³EHFDUHIXOZKHQPRYLQJ:KHQXVLQJDKDQG
truck, handle from the side only.
AVERTISSEMENT
Risque de basculement
Le réfrigérateur est beaucoup plus lourd en haut qu’en
bas. Il faut être prudent lors des déplacements. Si un
diable est utilisé, il faut soulever le réfrigérateur sur le
côté seulement.
• Carefully cut banding at the top and bottom, remove
the outer carton.
• Slide out the back corner posts (2).
• Slide the carton off the top of the cabinet.
NOTE: IT IS NOT NECESSARY TO LAY THE CABINET DOWN
IN ORDER TO REMOVE THE SKID!
• The unit is secured to the
skid with 4 slotted tiedown straps. Remove the
six 7/16” bolts from the
base channels in the tiedowns.
• Remove the six 7/16” bolts
securing the straps to the
Remove
skid.
Tie Downs
NOTE: DO NOT ATTEMPT TO
ROLL UNIT OFF SKID.
• The support blocks on the
bottom of the refrigeration
case must be removed before the refrigerator is taken
off the skid or damage will occur. Carefully tilt the
refrigerator and slide the blocks out from beneath.
• Remove the toekick and set aside for final installation.
• Lift the refrigerator off the skid with an appliance dolly.
Handle from the sides.
Floor
Cold Water Line
Toekick
Templates
NOTE: The only GE approved plastic tubing is supplied
in the GE SmartConnect™ Refrigerator Tubing kits. Do
not use any other plastic water supply line because
the line is under pressure at all times. Other types of
plastic may crack or rupture with age and cause water
damage to your home.
GE SmartConnect™ Refrigerator Tubing Kits are
available in the following lengths:
2’ (.6 m)
WX08X10002
6’ (1.8 m) WX08X10006
15’ (4.6 m) WX08X10015
25’ (7.6 m) WX08X10025
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the line
of water.
• Install a shut-off valve between the icemaker water
valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be
easily accessible.
• Turn on the main water supply and flush debris.
Run about a quart of water through the tubing into a
bucket. Shut off the water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are included in many
water supply kits. Before purchasing, make sure a saddle
type valve complies with your local plumbing codes.
STEP 2 MOVE THE REFRIGERATOR
INTO THE HOUSE
• Re-use the corner posts from the packaging to protect
stainless steel models. Run the appliance dolly straps
over the posts and under the handles.
• Leave the protective film on the refrigerator until
installation is complete.IMPORTANT: Never lift the
refrigerator by the handle or push against the grill
panel; this could cause damage or misalignment.
• Avoid laying the unit on its back or side to prevent
sealed system restrictions.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves
are illegal and use is not permitted in Massachusetts.
Consult with your licensed plumber.
16
Installation Instructions
STEP 7 ANIT-TIP PROCEDURE
STEP 4 INSTALLATION WITH
HOUSEHOLD WATER
FILTRATION SYSTEM
WARNING
Tip Over Hazard.
These refrigerators are top heavy, especially
with any doors open, and must be secured to
prevent tipping forward which could result in
death or serious injury. Read and follow the
entire installation instructions for securing the
refrigerator with the anti-tip system.
Skip this step if you do not have a household water
filtration system
If the water supply to the refrigerator is from any
household water filtration system, the filter cartridge
should be removed. For better ice and water
performance, remove the filter and install the filter bypass
plug.
AVERTISSEMENT
Risque de
basculement
Rotate Counterclockwise To
Remove
Ces réfrigérateurs présentent une partie
supérieure lourde, en particulier avec une porte
ouverte; ils doivent donc être fixés pour prévenir le
basculement vers l’avant et le risque concomitant
de blessure grave ou fatale. Lisez et suivez
les instructions d’installation complètes pour
l’installation du système anti-basculement.
Filter Bypass
Plug
Flush Installation Only
STEP 5 INSTALL SIDE PANELS
• Cut a 1/2” x 4” block, 35” long.
• Measure and mark under the soffit, 5-1/4” from the
front edge of the cabinet.
• Secure the wood block to under the soffit. From
the bottom of the block to the finished floor should
measure 84”. See the illustration.
Skip this step when not using side panels.
If you are using 1/4” side panels, they should be
inserted into the case trim. Fasten the panels to the
refrigerator with stick-on hook and loop fastener strips
before setting the refrigerator in place.
STEP 6 INSTALL CASE TRIM
Install case trim using supplied right hand and left hand
case trim pieces and case trim screws. Attach case trim
to each side of case as shown in illustration using case
trim screws in holes provided down each side of case.
17
Installation Instructions
STEP 8 LEVEL REFRIGERATOR
STEP 7 ANTI-TIP PROCEDURE (Cont.)
All models have 4-point leveling. The front is supported
by leveling legs, the rear is supported by adjustable
wheels. Both are accessible from the front of the
refrigerator.
• To level the back of the refrigerator, turn the 7/16”
hex nut located above
the front wheels. Turn
clockwise to raise or
counterclockwise to lower
the refrigerator.
• For front leveling, use
a
1-1/4” open-end wrench.
• Adjust height of
refrigerator to match
installation cutout opening
84-1/2”. The refrigerator should be level and plumb
with cabinetry.
NOTE (Flush Installation Only): Raise refrigerator until
the case top comes in contact with the 1/2” spacer
block mounted to the underside of the cabinet soffit.
Refrigerator should be level at fully raised position.
NOTICE: The rear leveling wheels and front leveling
legs are limited to a maximum height adjustment of 1”.
If the installation requires more than 84-1/2” height,
the installer should elevate the refrigerator on a sheet
of plywood or runners. Cabinetry trim could also be
added across the top of the opening to shorten the
opening. If you attempt to raise the refrigerator more
than 1”, you will damage the front leveling legs and
the rear leveling wheels. Make adjustments in small
increments.
Standard Installation Only
• Cut a 2” x 4” block, 35” long and secure the block to
the mounting brackets provided using #12 or #14
wood screws.
• Secure the bracket with wood block to the back wall
so that it is 84” from the finished floor. Use #12 or #14
wood screws. See the illustration.
• The screws must penetrate at least one inch into the
vertical wall studs.
IMPORTANT NOTE FOR STANDARD INSTALLATION:
When the refrigerator is installed under a soffit or if
there is not enough height for this method of security,
brackets cannot be used. Proceed to step 8 to level the
refrigerator and then to step 9 to secure refrigerator to
cabinets. See step 8 if you have metal wall studs. The
STEP 9 SECURE REFRIGERATOR
TO CABINETRY
Whenever possible, perform this step for anti-tip
security, or when anti-tip brackets cannot be used.
The refrigerator must be secured to prevent tipping.
• Raise the grille panel to access the machine
compartment.
• For flush inset installation only, drill a hole in the case
top and drive a screw through the top into the adjacent
1/2” block.
refrigerator must be secured to prevent tipping.
Connect power cord:
• Before pushing the refrigerator into the opening, plug
the power cord into the receptacle. Open the grille
panel and reach into the opening at the back to grasp
the power cord. Pull the power cord into the opening
as you push the refrigerator back.
• Gently push refrigerator into the opening with hands
against front corners.
18
Installation Instructions
STEP 10 ADJUST DOOR SWING
NOTE: This refrigerator has a 3-position door stop.
When space does not allow the door to swing open
fully to 115°, you may change the door swing to a
90° opening. A 130° door swing option is available
for standard installation only. Skip this step if door
opening is satisfactory for your installation situation.
• Open the door to view the bottom hinge.
Note the door stop pin locations. The pin is factory
installed in the 130° position.
• Close the door. From below, use pliers to unscrew
the door stop and reinstall into the 90° position.
STEP 11 REMOVE DOOR TRIM - FLUSH INSTALLATION ONLY
Use the supplied Torx wrench or T10 Torx head driver to
remove all exposed trim screws securing aluminum trim
to refrigerator doors. Save all trim and screws as they
will be replaced in a later step.
1. Remove screws from door hinge side of both left and
right doors. Once screws are removed, remove trim
from hinge side of each door.
2. Remove 4 trim screws on vertical handle side on each
door to release handle cover trim. Remove the handle
cover trim from the handle side of each door to expose
handle visor trim underneath.
3 Remove 4 additional trim screws from handle visor
trim on each door. Once screws have been removed,
remove handle visor trim from each door.
Handle
visor trim
Handle
side trim
Hinge side
trim
Hinge side
trim
19
Installation Instructions
STEP 12 LAYOUT DECORATIVE DOOR PANELS - FLUSH INSTALLATION ONLY
Decorative wood panels must be cut to a thickness of
3/4”. The dimensions of each panel can be determined by
referring to the specs provided with refrigerator. Panels
must be predrilled to prevent accidental splitting or
cracking of wood when attaching to door brackets in the
next step.
1. Cut Freezer (left) side and Fresh food (right) side panels
to specified dimensions (as noted on page 11 under
Design Guide).
2. Lay the Freezer and Fresh Food panels face down on a
non-scratch surface.
3. Mark a vertical centerline on the backside of the Freezer
and Fresh Food panels.
4. Lay supplied Fresh Food panel TEMPLATE (attached
to side case of refrigerator) on the back of the Fresh
Food panel with the lettering face up. See illustration
to ensure proper template has been selected. Align the
top, side, and centerline of the template with the top,
side and centerline of the door. Tape the template to
the panel using masking tape to temporarily secure it in
place.
5. Repeat previous step on the Freezer door panel using
the Freezer panel Template.
Template is
aligned with
top of FZ panel.
7. Using a pencil, trace the outline of the notch out of the
template at the top corner of each door. This mark will
provide a guide for routing wood to provide relief for
door hinge at top of door panel.
8. Remove the tape from each panel. Slide the templates
to the bottom of each panel aligning the bottom, sides,
and centerline of the panel with the bottom, sides and
centerline of the templates. Tape in place.
Move the
templates from
the tops to the
bottoms on the
back side of the
door panels.
Panel is face down
on a non-scratch
surface. You will be
drilling on the BACK
of the panel.
9. Using a 1/8” wood drill bit, drill pilot holes into the door
panels 1/4” deep through only the bottom group of
holes in the templates. Four holes will be drilled into the
bottom corners of each door.
Template is
aligned with
top of FF panel.
Panel is face down on a nonscratch surface. You will be drilling
on the BACK of the panel.
6. Using a 1/8” wood drill bit, drill pilot holes into the door
panels 1/4” deep through only the top group of holes
in the templates. Four holes will be drilled into the upper
corners of each door panel.
20
Installation Instructions
STEP 12 LAYOUT DECORATIVE DOOR PANELS - FLUSH INSTALLATION ONLY (Cont.)
10. Using a pencil, trace the outline of the notch out of the
template at the bottom corner of each door. This mark
will provide a guide for routing wood to provide relief for
door hinge at bottom of door panel.
11. Route out the traced areas on the rear of each panel
1/4” deep and discard the door panel templates.
Preparation for handles
1. Lay out the location of the custom handle on the back
of the door panel.
2. Counter-sink the handle screw locations on back of
the pane to avoid interference with the door frame.
Countersink 1/4” to maintain 1/2” minimum material
thickness.
STEP 13 ATTACH BRACKETS TO PANELS - FLUSH INSTALLATION ONLY
Locate wood panel brackets and wood panel screws in
Flush Inset Hardware Kit located inside the refrigerator
drawer. These brackets will install to rear of decorative
wood panels to provide attachment to refrigerator door
brackets already installed on doors.
1. Align the four tapered holes in the top left hand panel
bracket with the four pilot holes at the top hinge side of
the Freezer panel. Fasten the bracket using four screws.
2. Align the four tapered holes in the top right hand panel
bracket with the four pilot holes at the top hinge side of
the Fresh Food panel making sure the angled portion of
the bracket is facing the perimeter of the door. Fasten
the bracket using four screws.
3. Align the four tapered holes in the bottom left hand
panel bracket with the four pilot holes at the bottom
hinge side of the Freezer panel making sure the angled
portion of the bracket is facing the perimeter of the
door. Fasten the bracket using four screws.
Top Right
Panel Bracket
Top Left
Panel
Bracket
Top Right
Panel
Bracket
4. Align the four tapered holes in the bottom right hand
panel bracket with the four pilot holes at the bottom
hinge side of the Freezer panel making sure the angled
portion of the bracket is facing the perimeter of the
door. Fasten the bracket using four screws.
5. Align the four tapered holes in one of the top panel
brackets with the four holes in the top of the Freezer
door panel. Fasten the bracket using four screws.
Repeat with the Fresh Food panel.
6. Align the four tapered holes in one of the bottom
panel brackets with the four holes in the bottom of the
Freezer door panel making sure the angled portion of
the bracket is facing the perimeter of the door. Fasten
the bracket using four screws. Repeat with the Fresh
Food panel.
7. Install the custom handle on the front side of the door
panel. A washer should be used in the countersink hole
on the back of the panel.
Top
The Freezer Panel is
face down on a nonscratch surface.
Top Left Panel
Bracket
Bottom Right
Panel Bracket
Top
Bottom Left
Panel Bracket
The Fresh Food Panel
is face down on a
non-scratch surface.
Bottom Left
Panel Bracket
Bottom Right
Panel Bracket
21
Installation Instructions
STEP 14 HANG DECORATIVE DOOR PANELS - FLUSH INSTALLATION ONLY
Panels with attached brackets will mate with steel
brackets already attached to top, sides, and bottom of
refrigerator doors. Each bracket attached to the door
will have two machined screws recessed inside the door
to provide anchoring points for wood panel brackets to
install onto the doors.
1. Lift the Fresh Food door panel to hang the panel on the
fresh food door. Angle the bottom of the panel slightly
away from the fresh food door. The brackets mounted
at the top of the door panel will lay over the top of the
brackets mounted at the top of the fresh food door.
Allow the flanges of the door brackets to slide into the
slot at the top of the panel brackets and gently allow
the bottom edge of the panel to lay against the fresh
food door as it hangs freely.
Each screw should be tightened until snug, and then
backed off 2-3 turns to allow for fine tuning adjustment.
NOTE: If screws are fully tightened at this stage,
further panel adjustment will not be possible.
5. Thread set screws into each of the panel brackets
attached to the doors. Hinge side brackets will have 2
set screws each, going into the door. The handle side
brackets will each have 1 set screw going into the door.
Each panel bracket has a tab that is aligned with a tab
on the door bracket. Each of these will have a set screw
threaded into them (see illustration).
2. Repeat previous step with the freezer door panel. The
brackets mounted at the top of the freezer door panel
will lay over the top of the bracket mounted on the top
of the freezer door.
3. Adjust the panels on each door by pushing it flush
against the doors. Push each panel toward the center of
the refrigerator so the panels are as close to touching
each other as possible.
4. Using supplied washer-head screws, secure panel
brackets mounted to the rear of the wooden panels to
the refrigerator door; top, side and bottom.
22
Installation Instructions
STEP 15 LAYOUT DECORATIVE GRILLE
PANEL - FLUSH INSTALLATION
ONLY
STEP 16 INSTALL GRILLE PANEL - FLUSH
INSTALLATION ONLY
1. Pull grille panel bracket in an outward motion allowing
it to swing out and up to the fully open position.
2. Lay the grille panel on top of the grille panel bracket
and align the pilot holes with the bracket holes from the
underside.
3. Fasten the grille panel to the grille panel bracket using
provided screws in bracket hardware kit.
Grille area will also have decorative wood panel
attached to installed steel bracket. Pilot holes are
necessary to prevent splitting and cracking of wood
panel.
1. Cut wooden grille panel to specified dimensions as
noted on page 11.
2. Lay the grille panel face down on a non-scratch
surface.
3. Mark a vertical centerline on the back side of the grille
panel.
4. Lay supplied TEMPLATE to the back of the grille
panel with the lettering face up. Align the top, side,
and centerline of the template with the top side and
centerline of the door. Tape the template in place
using masking tape.
5. Using a 1/8” wood drill bit, drill pilot holes into the grille
panel 1/4” deep.
6. Remove tape and discard template.
23
Installation Instructions
STEP 17 ADJUST DECORATIVE PANELS - FLUSH INSTALLATION ONLY
Each door panel can be adjusted approximately 1/8”
both left and right, up and down, as well as outward
from the door to provide planar appearance with
cabinets.
NOTICE: Misaligned door panels from incorrect drilling
or incorrect cut dimensioning may result in less possible
adjustment as well as possible interferences with other
attached panels and/or hardware.
1. The gap between the outside edge of the door panels
and the cabinet opening should be 9/16”. Adjust panels
until specified gap is maintained.
3. Check that the fresh food and freezer door panels are
in plane with the face of the cabinets. The panel can be
adjusted outward by turning the set screw threaded into
the tab of the door bracket at the top and bottom of the
door clockwise until the face of the panel is in the same
plane as the cabinetry.
Turn set screws on tabs at
top and bottom of door to
move panel in or out to be
flush with cabinetry.
Door panels and hood panel should be
flush with the fronts of the cabinets.
9/16”
9/16”
4. Check the flushness of the panel with the cabinetry.
If the grille is not flush, adjustments can be made by
loosening the screws in the slots on the hinge and
moving the panel in or out. Once all adjustments are
made, retighten screws and close the grille.
Use these screws
to adjust the grille
panel in or out both sides.
2. Turn the set screw at the hinge side (top and bottom)
of the refrigerator clockwise to adjust the door panel
toward the edge of the door opening. Check the gap by
closing the door.
Turn set screw on
hinge side, top and
bottom, clockwise
to move toward the
door opening.
24
Installation Instructions
STEP 17 ADJUST DECORATIVE PANELS
- FLUSH INSTALLATION ONLY
(Cont)
STEP 18 REPLACE TRIM - FLUSH
INSTALLATION ONLY
1. Replace trim and 6 screws on hinge side of each door.
2. Replace handle visor trim and four screws on the
handle side of each door.
3. Replace trim cover and four screws over visor trim on
the handle side of each door.
5. Make the final vertical adjustment of the fresh food
and freezer door panels. Using the set screw at the
top of the door, turn clockwise until the desired gap
between the grille panel bottom and top panels of
doors appear satisfactory.
Hinge side
trim
Turn set screws on top and bottom
of door to move panel up or down
for desired gap with grille panel
bottom.
Handle
visor trim
Handle
side trim
Hinge side
trim
6. Tighten all washer-head screws (NOT SET SCREWS)
firmly to secure brackets and adjustments in place.
Start with bottom edge washer-head screws to
provide support of the door panel. Next, moving on to
top edge to prevent panel from moving from aligned
position. Finish by tightening hinge side washer-head
screws. NOTE: Over tightening washer-head screws
may result in bending wood panel brackets as well as
misaligning wood door
panels.
7. Drive the door anchor
screws through the
two white plastic
pockets in the side of
each door and into
the door panel (4 each
door) to prevent panel
warping over time.
25
Installation Instructions
STEP 20 CONNECT POWER, CLOSE
GRILLE PANEL
STEP 19 CONNECT WATER SUPPLY
• Open the grill panel.
• Plug in the power cord (if necessary) by reaching into
the opening next to the water filter. If access is too
tight, remove the 2 screws holding the water filter
bracket and move aside. Plug in the power cord and
secure the bracket with the original screws.
Refrigerator
Water Supply
Bracket
Screws
House
Water Supply
Master Light
Switches
• Locate and bring the tubing to the front of the cabinet.
• Turn the water on to flush debris from the line. Run
about a quart of water through the tubing into a
bucket, then shut off the water.
Electrical
Outlet Access
• Check to make sure power to refrigerator is on by
opening refrigerator door to see if interior lights are
on.
• The temperature controls are preset at 37°F for the
fresh food section and 0°F for the freezer.
• Allow 24 hours to stabilize before making
adjustments.
Copper Tubing:
• Slip a 1/4” nut and ferrule (provided) over both ends of
the copper tubing. Insert the tube into the union fitting
on the unit and tighten the nut to the union.
• Turn on the water to check for leaks.
GE SmartConnect™ Tubing:
NOTE: The only GE-approved plastic tubing is supplied
in the GE SmartConnect™ Refrigerator Tubing kits. Do
not use any other plastic water supply line because
the line is under pressure at all times. Other types of
plastic may crack or rupture with age and cause water
damage to your home.
STEP 21 START ICEMAKER
Icemaker
GE SmartConnect™ Refrigerator Tubing Kits are
available in the following lengths:
2’ (.6 m)
WX08X10002
8’ (2.4 m) WX08X10006
15’ (4.6 m) WX08X1 0015
25’ (7.6 m) WX08X10025
Power
Switch
• Insert the molded end of the tubing into the
refrigerator connection. Tighten the compression nut
until it is just hand tight.
• Tighten one additional turn with a wrench.
Overtightening can cause leaks!
• Turn on the water to check for leaks.
Feeler Arm
• Slide the switch to ON. The icemaker will begin
operation automatically.
• Be sure nothing interferes with the sweep of the feeler
arm.
• Discard the first full bucket of ice cubes.
• To turn the icemaker off, slide the switch to OFF.
NOTE: Make sure excess tubing length does not
interfere with the toekick installation.
26
Installation Instructions
STEP 22 INSTALL TOEKICKS
INSPECT FINAL INSTALLATION
• Locate the supplied toekicks (shipped taped to the
side of the refrigerator.
• Attach the LARGER toekick to the refrigerator using
ONLY the top center hole (1).
• Attach the toekick skirt to the refrigerator using the
three lower slots (2).
Check door alignment. Stand back away from the
refrigerator to inspect the final installation.
• Check to be sure the handles are evenly aligned with
each other at the top. To adjust, loosen the handle
screws and slide up or down. Tighten the screws.
• Shipping or the addition of heavy door panels may
have caused the doors to move slightly out of
alignment.
Door Out of
Alignment
1
2
Bushing
• A custom toekick can be installed to match or
complement the surrounding cabinetry. Use the
supplied toekick as a template to cut the shape.
Door H
inge
Case Hing
e
Raise
5/16" Wrench
• If necessary, the fresh food door may be adjusted up
or down to align with the freezer door.
• Use a 5/16” wrench to adjust the hinge pin as shown.
27
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
For Monogram® local service in your area, call
1.800.444.1845.
NOTE: Product improvement is a continuing endeavor at
General Electric. Therefore, materials, appearance and
specifications are subject to change without notice.
31-49057-1
224D1889P015
10-14 GE
Printed in the United States
GE
Appliances
Appliance Park
Louisville, KY 40225
GEAppliances.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement