Sony | WX-4500X | Installation instructions | Sony WX-4500X Installation Instructions

2
A
Changer Control
Audio Master
SUBWOOFER OUT
(MONO)
Installation/Connections
B
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
Source selector*
*
*
WX-4500X
Sony Corporation © 2001 Printed in Japan
BUS CONTROL IN
* not supplied
1
3 To AMP REMOTE IN of an optional power
1
2
×6
Cautions
3
• This unit is designed for negative ground 12 V
DC operation only.
• Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
• Before making connections, turn the car
ignition off to avoid short circuits.
• Connect the yellow and red power input leads
only after all other leads have been connected.
• Run all ground wires to a common ground
point.
• Be sure to insulate any loose unconnected
wires with electrical tape for safety.
• The use of optical instruments with this
product will increase eye hazard.
×6
4
For NISSAN cars only
Notes on the power supply cord (yellow)
• When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Equipment used in illustrations (not supplied)
Front speaker
Parts Iist (1)
Power amplifier
The numbers in the list are keyed to those in the
instructions.
Rear speaker
Active subwoofer
Connection example (2)
CD/MD changer
Tip (2-B- )
For connecting two or more changers, the source
selector XA-C30 (optional) is necessary.
Connection diagram (3)
Rotary commander RM-X4S
When insert the each connector, be sure to insert
it securely, as vibration through driving may
cause a poor connection.
1 To a metal surface of the car
2
*I-3-229-007-11*
(1)
First connect the black ground lead, then
connect the yellow and red power input leads.
To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there
is no power antenna or antenna booster, or
with a manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
4
5
6
7
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
To the interface cable of a car telephone
To a car’s illumination feed
Be sure to connect the black ground lead to it
first.
To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black ground lead to it
first.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
To the +12 V power terminal which is energised
at all times
Be sure to connect the black ground lead to it
first.
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies
+12 V DC when you turn on the tuner.
• When your car has built-in FM/AM antenna in the
rear/side glass, connect the power antenna control
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing antenna
booster. For details, consult your dealer.
• A power antenna without relay box cannot be
used with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
• Do not connect the ground lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker wires installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
• Do not connect the unit’s speaker cords to each
other.
3
Source selector*1
*1
*1
Supplied with XA-C30
BUS CONTROL IN
SUBWOOFER OUT
(MONO)
BUS AUDIO IN
Supplied with the CD/MD changer
REMOTE IN
MONO
MONO
*1
*2
L
R
SUB WOOFER OUT BUS AUDIO IN
*1
*2
RCA pin cord (not supplied)
*
2
*1
*2
Fuse (10 A)
4
Black
Blue
ANT REM
1
Max. supply current 0.1 A
2
Blue/white striped
White
AMP REM
Left
Max. supply current 0.3 A
White/black striped
3
Light blue
ATT
Gray
4
Right
Gray/black striped
Orange/white striped
ILLUMINATION
5
Green
Red
Left
Green/black striped
Purple
6
Yellow
Right
7
Purple/black striped
3
•
•
3
4
5
•
6
•
•
4
5
•
•
•
•
•
•
6
•
•
7
•
•
•
7
•
•
•
1
•
•
•
•
•
•
1
2
2
2
•
2
3
•
•
1
•
2
3
•
•
•
•
•
1
2
•
•
•
•
•
•
•
•
•
•
•
not supplied
Connect the Bus cable to its
terminal with the unit’s V mark
and the Bus cable’s v mark
aligned.
4 A
B
TOYOTA/MITSUBISHI
NISSAN
This illustration is for TOYOTA cars.
Bracke
1 or 2
1 or 2
max. size
5 × 8 mm (7/32 × 11/32 in.)
1
max. size
5 × 8 mm (7/32 × 11/32 in.)
to dashboard/center console
2
1
2
Bracket
3
1 or 2
Existing parts supplied with your car
max. size
5 × 8 mm (7/32 × 11/32 in.)
1
Existing parts
2
Bracket
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
When mounting this unit to the preinstalled
brackets of your car, use the supplied screws 1
or 2 in the appropriate screw holes, according
to your vehicle: T for TOYOTA, M for
MITSUBISHI, and N for NISSAN.
1
2
•
•
T
N
M
M
T
N
M
T
T
•
N
T
M
N
T
T
N
T
N
N
T
T
Mounting angle adjustment
N
N
M
N
M
Adjust the mounting angle to less than 20°.
Frequency select switch
The AM (FM) tuning interval is factory-set to the
9 k (50 k) position. If the frequency allocation
system of your country is based on 10 kHz (200
kHz) interval, set the switch on the left side of
the unit to the 10 k (200 k) position before
making connections.
After the frequency select switch is set, you
must press the reset button to reset the unit.
T
N
M
M
T
N
T
T
N
N
T
N
•
Notes
• Use the screws 1 or 2 depending on the make of
car. When this unit is attached to a MITSUBISHI car,
use the supplied screws 2.
• To prevent malfunction, be sure to install using
brackets and the supplied screws 1 or 2.
• Do not apply excessive force to the buttons of the
unit.
• Do not push on the display window.
• Before mounting, make sure there is nothing on
the top of the unit.
1
2
2
•
1
2
•
•
•
T
N
M
M
T
N
T
T
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
N
N
T
N
M
(OFF)
(OFF)
M
Be sure to press (OFF) on the unit for two
seconds to turn off the clock display after
turning off the engine.
When you press (OFF) only momentarily, the
clock display does not turn off and this causes
battery wear.
CD
To set the frequency select switch, use a
pointed object, such as a ball-point pen, to
gently slide the switch.
DSO
Reset button
Mounting the unit in a Japanese
car (4)
CD
DSO
EQ7
DSPL
SCRL
OFF
SOUND
MENU
MD
ATT
SA
SEEK/AMS
DSPL
SCRL
OFF
When the installation and connections are
completed, be sure to press the reset button with
a ball-point pen, etc.
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
EQ7
SEEK/AMS
MODE
SOURCE
Reset button
Note
When you connect the power supply cord to the
unit or reset the unit, wait for about 10 seconds
before you insert a disc. If you insert a disc within
these 10 seconds, the unit will not be reset, and you
will have to press the reset button again.
4
SEEK/AMS
SOUND
MENU
MD
ATT
SA
SEEK/AMS
MODE
SOURCE
B
NISSAN
Bracket
1 or 2
max. size
5 × 8 mm (7/32 × 11/32 in.)
rd/center console
1
to dashboard/center console
2
3
1 or 2
1 or 2
max. size
5 × 8 mm (7/32 × 11/32 in.)
1
max. size
5 × 8 mm (7/32 × 11/32 in.)
Existing parts supplied with your car
2
1
Bracket
2
Bracket
1
2
T
N
•
•
T
N
M
M
M
T
N
T
M
T
•
•
•
•
T
N
T
N
N
T
N
N
M
T
N
T
N
M
•
1
•
•
•
•
•
2
2
•
1
T
N
2
M
•
•
•
M
T
N
T
T
N
N
T
N
M
T
N
M
M
T
N
T
T
N
N
T
N
M
(OFF)
(OFF)
CD
DSO
EQ7
DSPL
SCRL
OFF
SEEK/AMS
SOUND
4
CD
DSO
EQ7
DSPL
SCRL
OFF
4
SEEK/AMS
SOUND
MENU
MD
ATT
SA
SEEK/AMS
MODE
SOURCE
MENU
MD
ATT
SA
SEEK/AMS
MODE
SOURCE
ket
to dashboard/center console
3
1 or 2
max. size
5 × 8 mm (7/32 × 11/32 in.)
s supplied with your car
1
2
Bracket
T
N
•
•
•
M
M
T
N
T
T
N
N
T
N
M
•
•
•
•
•
T
N
M
M
T
N
T
T
N
N
T
N
M
CD
DSO
EQ7
DSPL
SCRL
OFF
SEEK/AMS
SOUND
4
MENU
MD
ATT
SA
SEEK/AMS
MODE
SOURCE
Download PDF

advertising