Sony | Xplod CDX-M800 | User's Manual | Sony Xplod CDX-M800 User's Manual

CDX-M800
SERVICE MANUAL
US Model
Canadian Model
AEP Model
UK Model
E Model
Ver 1.0 2003. 01
• The tuner and CD sections have no adjustments.
SPECIFICATIONS
Model Name Using Similar Mechanism
CDX-L410X/L490X
CD Drive Mechanism Type
MG-393XC-121//K
Optical Pick-up Name
KSS-721A
MW/LW (AEP, UK, E model)
Tuning range
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Aerial terminal
External aerial connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
MW: 30 µV
LW: 40 µV
AUDIO POWER SPECIFICATIONS (US MODEL)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
CD player section
Signal-to-noise ratio
Frequency response
Wow and flutter
90 dB
10 – 20,000 Hz
Below measurable limit
Power amplifier section
Outputs
Speaker outputs (sure seal connectors)
Speaker impedance
4 – 8 ohms
Maximum power output 52 W × 4 (at 4 ohms)
Tuner section
FM
Tuning range
General
87.5 – 107.9 MHz (US, Canadian model)
87.5 – 108.0 MHz (AEP, UK, E model)
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
67 dB (stereo),
69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo),
0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
Outputs
Audio outputs (front/rear)
Subwoofer output (mono)
Power antenna relay
control terminal (US, Canadian model)
Power aerial relay
control terminal (AEP, UK, E model)
Power amplifier control
terminal
– Continued on next page –
AM (US, Canadian model)
Tuning range
530 – 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
30 µV
FM/AM COMPACT DISC PLAYER
US, Canadian Model
FM/MW/LW COMPACT DISC PLAYER
AEP, UK, E Model
9-874-299-01
Sony Corporation
2003A0400-1
© 2003. 01
e Vehicle Company
Published by Sony Engineering Corporation
1
CDX-M800
Inputs
Tone controls
Loudness
Power requirements
Dimensions
Mounting dimensions
Mass
Supplied accessories
Telephone ATT control
terminal
Illumination control terminal (US, Canadian model)
BUS control input terminal
BUS audio input or AUX IN terminal
Antenna input terminal (US, Canadian model)
Aerial input terminal (AEP, UK, E model)
US, Canadian model:
Bass ±10 dB at 62 Hz
Treble ±10 dB at 16 kHz
AEP, UK, E model:
Bass ±8 dB at 100 Hz
Treble ±8 dB at 10 kHz
+8 dB at 100 Hz
+2 dB at 10 kHz
12 V DC car battery
(negative ground)
Approx. 178 × 50 × 186 mm
(7 1/8 × 2 × 7 3/8 in.)
(w/h/d)
Approx. 182 × 53 × 163 mm
(7 1/4 × 2 1/8 × 6 1/2 in.)
(w/h/d)
Approx. 1.5 kg (2 lb. 10 oz.)
Parts for installation and
connections (1 set)
Card remote commander
RM-X110 (US, Canadian model)
RM-X111 (AEP, UK, E model)
SERVICE NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
Note
This unit cannot be connected to a digital preamplifier or an equalizer.
Design and specifications are subject to change without
notice.
US, Canadian model:
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical
pick-up block.
optical pick-up block
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
2
semi-fixed resistor
CDX-M800
AEP, UK, E model:
Notes on CD-R/CD-RW discs
• You can play CD-Rs (recordable CDs)/CD-RWs (rewritable CDs)
designed for audio use on this unit.
Look for these marks to distinguish CD-Rs/CD-RWs for audio
use.
This label is located on the bottom of the chassis.
These marks denote that a disc is not for audio use.
• Some CD-Rs/CD-RWs (depending on the equipment used for
its recording or the condition of the disc) may not play on this
unit.
• You cannot play a CD-R/a CD-RW that is not finalized∗.
This label is located on the drive unit’s internal chassis.
When replacing the chassis (T) of mechanism deck which have
the “CAUTION LABEL” attached, please be sure to put a new
CAUTION LABEL (3-223-913-11) to the chassis (T).
∗ A process necessary for a recorded CD-R/CD-RW disc to be
played on the audio CD player.
NOTE FOR THE OPENING OF THE FRONT PANEL
In this set, the front panel is lowered to below the bottom face when
it is opened.
When servicing the set, place it on a stand having a height of about
2 cm.
stand
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following
test discs should be used to check the capability:
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1)
CD-RW test disc TCD-W082L (Part No. J-2502-063-2)
3
CDX-M800
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
• Connect the MAIN board (CNP301) and the SERVO board (CN1)
with the extension cable (Part No. J-2502-062-1).
MAIN BOARD CNP301
SERVO BOARD CN1
4
CDX-M800
TABLE OF CONTENTS
1. GENERAL
Location of Controls ................................................................ 6
Connection example (US, Canadian Model) ........................... 6
Connections (US, Canadian Model) ........................................ 7
2. DISASSEMBLY
2-1. Front Panel Assy ................................................................. 8
2-2. CD Mechanism Block, Front Panel Assy ............................ 9
2-3. Sub Panel (CD) Sub Assy ................................................... 9
2-4. Motor Block Assy, Cam (R) Assy ..................................... 10
2-5. Main Board ....................................................................... 10
2-6. Heat Sink ........................................................................... 11
2-7. Chassis (T) Sub Assy ........................................................ 11
2-8. Lever Section, In Self SW Board ...................................... 12
2-9. Servo Board ....................................................................... 12
2-10. Shaft Roller Assy, Load SW Board ................................... 13
2-11. Floating Block Assy .......................................................... 13
2-12. Optical Pick-up Block ....................................................... 14
3. PHASE ALIGNMENT
3-1.
3-2.
3-3.
3-4.
Arm (A-L) Assy, Arm (B-L) Assy ..................................... 15
Cam (L) ............................................................................. 15
Motor Block ...................................................................... 16
Alignment between Arm (A-L) Assy
and Arm (B-L) Assy .......................................................... 16
3-5. Arm (A-R) Assy, Arm (B-R) Assy .................................... 17
3-6. Cam (R) ............................................................................. 17
4. DIAGRAMS
4-1. IC Pin Descriptions ........................................................... 18
4-2. Block Diagram –CD Section– ........................................... 21
4-3. Block Diagram –Tuner Section– ....................................... 22
4-4. Block Diagram –Display Section– .................................... 23
4-5. Circuit Boards Location .................................................... 24
4-6. Schematic Diagram –CD Mechanism Section– ................ 25
4-7. Printed Wiring Boards –CD Mechanism Section– ............ 26
4-8. Printed Wiring Boards –Main Section– ............................ 28
4-9. Schematic Diagram –Main Section (1/2)– ........................ 30
4-10. Schematic Diagram –Main Section (2/2)– ........................ 31
4-11. Printed Wiring Board –Sub Section– ................................ 32
4-12. Schematic Diagram –Sub Section– ................................... 33
4-13. Printed Wiring Board –Display Section– .......................... 34
4-14. Schematic Diagram –Display Section– ............................. 35
4-15. IC Block Diagrams ............................................................ 36
5. EXPLODED VIEWS
5-1.
5-2.
5-3.
5-4.
5-5.
5-6.
5-7.
Chassis Section ................................................................. 39
Cam Section ...................................................................... 40
Main Board Section .......................................................... 41
Front Panel Section ........................................................... 42
CD Mechanism Section (1) ............................................... 43
CD Mechanism Section (2) ............................................... 44
CD Mechanism Section (3) ............................................... 45
6. ELECTRICAL PARTS LIST ......................................... 46
5
CDX-M800
SECTION 1
GENERAL
This section is extracted
from instruction manual.
Main display side
Location of controls (US, Canadian Model)
Card remote commander RM-X110
(DISC) (M):
to select upwards
OPEN/CLOSE
SCRL
DSPL
REP
SHUF
1
2
4
DISC +
(SEEK) (<):
to select
leftwards
3
5
6
EQ7
MODE
DSO
MENU
DISC +
LIST
SEEK–
SOUN
D
OFF
SOURCE
DISC –
+
SEEK+
(SEEK) (,):
to select
rightwards
DISC –
(DISC) (m):
to select downwards
SEEK+
ENTE
SEEK–
SOURCE
In menu mode, the currently selectable button(s) of
these four are indicated with a “ v” in the display.
Operation side
R
ATT
VOL
–
Note
If the display disappears by pressing (OFF), it cannot
be operated with the card remote commander unless
(SOURCE) on the unit is pressed, or a disc is inserted
to activate the unit first.
Tip
Refer to “Replacing the lithium battery” for details on
how to replace the batteries (page 22).
Refer to the pages listed for details.
a SCRL (scroll) button 10
b DSPL (display mode change) button
10, 12
c Number buttons
(1) REP 11
(2) SHUF 11
To store stations/receive stored stations.
d EQ7 button 18
e MENU button
To display the menus.
f SOURCE (Power on/Radio/CD/MD*1/
AUX*2) button
To select the source.
g SEEK (</,) buttons
To skip tracks/fast-forward, reverse a track/
tune in stations automatically, find a station
manually/select a setting.
h SOUND button 16
i OFF (Stop/Power off) button 9, 21
j VOL (+/–) buttons
To turn up or down the volume.
k OPEN/CLOSE button 9
l MODE button
To change the operation.
m DSO button 19
n LIST button 13, 16
o DISC (M/m) buttons
To receive preset stations/change the disc*3,
skip albums*4/select a menu.
p ENTER button
To enter a setting.
q ATT button 17
*1 When an optional MD unit is connected.
*2 Available only when an optional Sony portable
device is connected to BUS AUDIO IN of the unit.
You cannot connect any optional CD/MD units at
the same time.
*3 When an optional CD/MD unit is connected.
*4 Available only when an optional CD unit with the
MP3 file control function is connected, and MP3 file
is played.
4
CDX-M800
The buttons on the unit share the same
functions as those on the card remote
commander.
a
b
c
d
e
f
g
h
i
j
k
m
o
OPEN button 9
Main display window
IMAGE button 20
qf Receptor for the card remote
commander
qs RESET button 8
OFF (Stop/Power off) button*1
SCRL (scroll) button
DSPL (display mode change) button
Sub display window
SEEK/AMS (.m/M>) button
MENU button
LIST/CAT*2 button
CLOSE (front panel close) button 9
p
q
r
s
t
u
v
w
x
SOURCE button
MODE button
VOL (–/+) button
DSO button
EQ7 button
SOUND button
DISC (+/–) buttons
ENTER button
Z (eject) button 9
continue to next page t
5
Connection example (US, Canadian Model)
Connection example (2)
Notes (2-A)
• Be sure to connect the ground cord before connecting
the amplifier.
• If you connect an optional power amplifier and do not
use the built-in amplifier, the beep sound will be
deactivated.
Tip (2-B-
2
A
AUDIO OUT
FRONT
)
For connecting two or more CD/MD changers, the source
selector XA-C30 (optional) is necessary.
SUB OUT (MONO)
Exemple de raccordement (2)
Remarques (2-A)
• Raccordez d’abord le fil de masse avant de raccorder
l’amplificateur.
• Si vous raccordez un amplificateur de puissance en
option et que vous n’utilisez pas l’amplificateur intégré,
le bip sonore est désactivé.
Conseil (2-B-
AUDIO OUT
REAR
)
Dans le cas du raccordement de deux changeurs de
CD/MD ou plus, le sélecteur de source XA-C30 (en option)
est requis.
Ejemplo de conexiones (2)
Notas (2-A)
• Asegúrese de conectar primero el cable de puesta a masa
antes de realizar la conexión al amplificador.
• Si conecta un amplificador de potencia opcional y no utiliza
el incorporado, los pitidos se desactivarán.
Consejo (2-B-
B
BUS AUDIO IN
)
Cuando desee conectar dos o más cambiadores de CD/MD,
necesitará un selector de fuente XA-C30 (opcional).
BUS CONTROL IN
BUS AUDIO IN
Source selector*
Sélecteur de source*
Selector de fuente*
XA-C30
BUS CONTROL IN
6
* not supplied
non fourni
no suministrado
CDX-M800
Connections (US, Canadian Model)
3
*1
Source selector
(not supplied)
Sélecteur de source
(non fourni)
Selector de fuente
(no suministrado)
*4
*3
XA-C30
*2
from car antenna
à partir de l’antenne de la voiture
desde la antena del automóvil
BUS AUDIO IN
/AUX IN *5
Supplied with the CD/MD changer
Fourni avec le changeur de CD/MD
Suministrado con el cambiador de CD/MD
AUDIO OUT
FRONT
*1 RCA pin cord (not supplied)
Cordon à broche RCA (non fourni)
Cable con terminales RCA (no
suministrado)
L
*2 Supplied with XA-C30
Fourni avec le XA-C30
Suministrado con el XA-C30
R
BUS
AUDIO IN
AUX IN
*1
SUB OUT (MONO)
3
AMP REM
REAR
FRONT
AUDIO OUT
Fuse (10 A)
Blue/white striped
Fusible (10 A)
Rayé bleu/blanc
Fusible (10 A)
Con rayas azules y blancas
Max. supply current 0.3 A
Courant max. fourni 0,3 A
Corriente máx. de alimentación de 0,3 A
Left
Gauche
Izquierdo
Right
Droit
Derecho
Left
Gauche
Izquierdo
Right
Droit
Derecho
White
Blanc
Blanco
White/black striped
Rayé blanc/noir
Con raya blanca/negra
Gray
Gris
Gris
Gray/black striped
Rayé gris/noir
Con raya gris/negra
Green
Vert
Verde
Green/black striped
Rayé vert/noir
Con raya verde/negra
Purple
Mauve
Morado
*3 Auxiliary optional equipment such as
portable DVD player (not supplied)
Appareil auxiliaire en option, par
exemple un lecteur de DVD (non
fourni)
Equipo opcional auxiliar como un
reproductor de DVD portátil (no
suministrado)
BUS
CONTROL IN
AUDIO OUT
REAR
4
Black
Noir
Negro
1
Blue
Bleu
Azul
ANT REM
Light blue
Bleu ciel
Azul celeste
Max. supply current 0.1 A
Courant d’alimentation max. 0,1 A
Corriente máx. de alimentación de 0,1 A
Orange/white striped
Rayé orange/blanc
Con rayas naranjas y blancas
ATT
Red
Rouge
Rojo
Yellow
Jaune
Amarillo
Purple/black striped
Rayé mauve/noir
Con raya violeta/negra
Schéma de raccordement (3)
Diagrama de conexión (3)
1 To a metal surface of the car
1 À un point métallique de la voiture
1 A una superficie metálica del automóvil
2 To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there is no
power antenna or antenna booster, or with a
manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control and
power supply leads.”
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4 To the interface cable of a car telephone
5 To a car’s illumination signal
Be sure to connect the black ground lead to a metal
surface of the car.
6 To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessoryposition, connect to the +12
V power (battery) terminal which is energized at
all times.
Be sure to connect the black ground lead to a
metal surface of the car.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control and
power supply leads.”
7 To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground lead to a metal
surface of the car.
Notes on the control and power supply leads
• The power antenna control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM antenna in the rear/
side glass, connect the power antenna control lead
(blue) or the accessorypower input lead (red) to the
power terminal of the existing antenna booster. For
details, consult your dealer.
• A power antenna without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected, power
will always be supplied to the memory circuit even when
the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and
with adequate power handling capacities to avoid its
damage.
• Do not connect the speaker terminals to the car
chassis,or connect the terminals of the right speakers
with those of the left speaker.
• Do not connect the ground lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in speaker
wires installed in your car if the unit shares a common
negative (–) lead for the right and left speakers.
• Do not connect the unit’s speaker cords to each other.
Note on connection
If speaker and amplifier are not connected correctly,
“Failure” appears in the display. In this case, make sure
the speaker and amplifier are connected correctly.
Branchez d‘abord le fil de masse noir et, ensuite, les fils d‘entrée
d‘alimentation jaune et rouge.
2 Vers le fil de commande de l‘antenne électrique ou le fil
fuente de alimentación del amplificador de antena
Notas
• Si no se dispone de antena motorizada ni de amplificador de
antena, o se utiliza una antena telescópica accionada
manualmente, no será necesario conectar este cable.
• Si el automóvil incorpora una antena de FM/AM en el cristal
trasero o lateral, consulte “Notas sobre los cables de control y
de fuente de alimentación”.
puissanceen option
4 Vers le cordon de liaison d’un téléphone de voiture
5 Vers le connecteur du signal d’éclairage de la voiture
Raccordez d‘abord le fil de masse noir à un point métallique de
la voiture.
6 À la borne +12 V qui est alimentée quand la clé de contact
est sur la position accessoires
Remarques
• S'il n'y a pas de position accessoires,raccordez la borne
d'alimentation (batterie) +12 V qui est alimentée en
permanence.
Raccordez d‘abord le fil de masse noir à un point métallique
de la voiture.
• Si votre voiture est équipée d'une antenne FM/AM intégrée
dans la vitre arrière/latérale, voir “Remarques sur les fils de
commande et d'alimentation”.
7 À la borne +12 V qui est alimentée en permanence
Raccordez d‘abord le fil de masse noir à un point métallique de
la voiture.
Remarques sur les fils de commande et d'alimentation
• Le fil de commande de l’antenne électrique (bleu) fournit une
alimentation de + 12 V CC lorsque vous mettez la radio sous
tension.
• Lorsque votre voiture est équipée d’une antenne FM/AM intégrée
dans la vitre arrière/latérale, raccordez la sortie de commande de
l’antenne (bleu) ou l’entrée d’alimentation des accessoires(rouge)
à la borne de l’amplificateur d’antenne existant. Pour plus de
détails, consultez votre détaillant.
• Une antenne électrique sans boitier de relais ne peut pas être
utilisée avec cet appareil.
Raccordementpour la conservation de la mémoire
Lorsque le fil d’entrée d’alimentation jaune est raccordé, le circuit
de la mémoire est alimenté en permanence même si la clé de
contact est sur la position d’arrêt.
Remarques sur le raccordement des haut-parleurs
• Avant de raccorder les haut-parleurs, mettez l’appareil hors
tension.
• Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms
avec une capacité électrique adéquate pour éviter de les
endommager.
• Ne raccordez pas les bornes du système de haut-parleur au châssis
de la voiture et ne raccordez pas les bornes du haut-parleur droit
à celles du haut-parleur gauche.
• Ne raccordez pas le câble de masse de cet appareil à la borne
négative (–) de l’enceinte.
• N’essayez pas de raccorder les haut-parleurs en parallèle.
• Raccordez uniquement des haut-parleurs passifs. Le raccordement
de haut-parleurs actifs (avec amplificateurs intégrés) aux bornes
des haut-parleurs peut endommager l’appareil.
• Pour éviter tout dysfonctionnement, n’utilisez pas les fils des hautparleurs intégrés installés dans votre voiture si l’appareil partage
un fil négatif commun (–) pour les haut-parleurs droit et gauche.
• Ne raccordez pas entre eux les cordons des haut-parleurs de
l’appareil.
Remarque sur le raccordement
Si les enceintes et l’amplificateur ne sont pas raccordés
correctement, le message “Failure” s’affiche. Dans ce cas, assurezvous que les enceintes et l’amplificateur sont bien raccordés.
6
7
Conecte primero el cable de puesta a masa negro, y después los
cables amarillo y rojo de entrada de alimentación.
• Il n'est pas nécessaire de raccorder ce fil s'il n'y a pas
d'antenne électrique ni d'amplificateur d'antenne, ou avec
une antenne télescopique manuelle.
• Si votre voiture est équipée d'une antenne FM/AM intégrée
dans la vitre arrière/latérale, voir “Remarques sur les fils de
commande et d'alimentation”.
Ce raccordement s’applique uniquement aux amplificateurs. Le
branchement de tout autre système risque d’endommager
l’appareil.
5
*5 Be sure to match the color-coded code
for audio to the appropriate jacks from
the unit. If you connect an optional CD/
MD unit, you cannot use AUX IN
terminal.
Veillez à faire correspondre le code
couleur audio aux fiches de l’appareil.
Si vous raccordez un appareil CD ou
MD en option, vous ne pouvez pas
utiliser la borne AUX IN.
Asegúrese de hacer coincidir el código
codificado con colores para audio con
las tomas apropiadas de la unidad. Si
conecta una unidad de CD/MD
opcional, no podrá utilizar el terminal
AUX IN.
2 Al cable de control de la antena motorizada o al cable de
d‘alimentation de l‘amplificateur d‘antenne
Remarques
3 Au niveau du AMP REMOTE IN de l’amplificateur de
4
ILLUMINATION
Connection diagram (3)
First connect the black ground lead, then connect
the yellow and red power input leads.
2
*4 Supplied with the auxiliary equipment
Fourni avec l’appareil auxiliaire
Suministrado con el equipo auxiliar
3 Para conectar a AMP REMOTE IN del amplificador de
potencia opcional
Esta conexión es sólo para amplificadores.
La conexión de cualquier otro sistema puede dañar la unidad.
4 Al cable de interfaz de un teléfono para automóvil
5 A una señal de iluminación del automóvil
Asegúrese de conectar primero el cable de tierra negro a una
superficie metálica del automóvil.
6 Al terminal de alimentación de +12 V que recibe energía en
la posición de accesoriodel interruptor de la llave de
encendido
Notas
• Si no hay posición de accesorio, conéctelo al terminal de
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de tierra negro a una
superficie metálica del automóvil.
• Si el automóvil incorpora una antena de FM/AM en el cristal
trasero/lateral, consulte “Notas sobre los cables de control y de
fuente de alimentación”.
7 Al terminal de alimentación de +12 V que recibe energía sin
interrupción
Asegúrese de conectar primero el cable de tierra negro a una
superficie metálica del automóvil.
Notas sobre los cables de control y de fuente de alimentación
• El conductor de control de la antena motorizada (azul) suministrará
+ cc 12 V cuando conecte la alimentación del sintonizador.
• Si el automóvil dispone de una antena de FM/AM incorporada en el
cristal trasero o lateral, conecte el cable de control de antena
motorizada (azul) o el cable de entrada de alimentación auxiliar
(rojo) al terminal de alimentación del amplificador de antena
existente. Para obtener información detallada, consulte a su
proveedor.
• Con esta unidad no es posible utilizar una antena motorizada sin
caja de relé.
Conexión para protección de la memoria
Si conecta el conductor de entrada amarillo, el circuito de la memoria
recibirá siempre alimentación, aunque ponga la llave de encendido
en la posición OFF.
Notas sobre la conexión de los altavoces
• Antes de conectar los altavoces, desconecte la alimentación de la
unidad.
• Utilice altavoces con una impedancia de 4 a 8 Ω con la capacidad de
potencia adecuada para evitar que se dañen.
• No conecte los terminales de altavoz al chasis del automóvil, ni
conecte los terminales del altavoz derecho con los del izquierdo.
• No conecte el cable de puesta a masa de esta unidad al terminal
negativo (–) del altavoz.
• No intente conectar los altavoces en paralelo.
• Conecte solamente altavoces pasivos. Si conecta altavoces activos
(con amplificadores incorporados) a los terminales de altavoz,
puede dañar la unidad.
• Para evitar fallos de funcionamiento, no utilice los cables de altavoz
incorporados instalados en el automóvil si su unidad comparte un
cable negativo común (–) para los altavoces derecho e izquierdo.
• No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión
Si el altavoz y el amplificador no están conectados correctamente,
aparecerá “Failure” en la pantalla. Si es así, compruebe la
conexión de ambos dispositivos.
7
CDX-M800
SECTION 2
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
SET
2-1.
FRONT PANEL ASSY
(Page 8)
2-2.
CD MECHANISM BLOCK,
FRONT PANEL ASSY
(Page 9)
2-7.
CHASSIS (T) SUB ASSY
(Page 11)
2-8.
LEVER SECTION,
IN SELF SW BOARD
(Page 12)
2-9.
SERVO BOARD
(Page 12)
2-3.
SUB PANEL (CD) SUB ASSY
(Page 9)
2-4.
MOTOR BLOCK ASSY,
CAM (R) ASSY
(Page 10)
2-10.
SHAFT ROLLER ASSY,
LOAD SW BOARD
(Page 13)
2-5.
MAIN BOARD
(Page 10)
2-11.
FLOATING BLOCK ASSY
(Page 13)
2-6.
HEAT SINK
(Page 11)
2-12.
OPTICAL PICK-UP BLOCK
(Page 14)
Note : Follow the disassembly procedure in the numerical order given.
2-1. FRONT PANEL ASSY
2 screw (panel)
3
flexible board
4 front panel assy
(Take care not to pull the
flexible board excessively)
8
1 screw (panel)
CDX-M800
2-2. CD MECHANISM BLOCK, FRONT PANEL ASSY
7 bracket (CD)
5 CD mechanism block
6 PTT 2.6x6
8 tension spring (flexible)
0 cover (flexible)
9 slider (flexible)
3 PTT 2.6x4
qa CNP909
slider (flexible)
flexible board
2 PTT 2.6x4
Note: When installing
the flexible board,
make the board slack
as illustrated.
1 PTT 2.6x6
4 CNP301
qs front panel assy
2-3. SUB PANEL (CD) SUB ASSY
1 CNP805
3 claws
2 claws
4 sub panel (CD) sub assy
9
CDX-M800
2-4. MOTOR BLOCK ASSY, CAM (R) ASSY
Note : Install the motor block assy and cam (R) assy in this roder.
For phase alignment between cams (L) and (R), see page 15 and 17.
1 PTT 2.6x6
4 PTT 2.6x6
5 motor block assy
Note: Install the cam (R) assy with
the cam fully rotated in the
direction of the arrow A.
A
2 cam (R) assy
3 CNP902
2-5. MAIN BOARD
5 MAIN board
4 PTT 2.6x6
ground point
3 PTT 2.6x6
ground point
2 PTT 2.6x6
1 PTT 2.6x6
10
CDX-M800
2-6. HEAT SINK
5 heat sink
4 PTT 2.6x6
3 PTT 2.6x12
1 PTT 2.6x6
2 PTT 2.6x6
2-7. CHASSIS (T) SUB ASSY
2 P 2x3
3 P 2x3
1 Unsolder the
lead wires.
4 chassis (T) sub assy
black
red
white
11
CDX-M800
2-8. LEVER SECTION, IN SELF SW BOARD
5 guide (disc)
6 lever (R)
3 tension spring (LR)
7 lever (L)
1 special screw
2 IN SELF SW board
4 claws
2-9. SERVO BOARD
8 SERVO board
7 special screw
6 special screws
2 Removal the solders.
9 FLEXIBLE board
1 CN3
4 P 2x3
3 Unsolder the
lead wires.
black
5 loading motor assy
yellow
optical pick-up block
12
CDX-M800
2-10. SHAFT ROLLER ASSY, LOAD SW BOARD
3 retaining ring (RA)
4 shaft retainer (roller)
shaft retainer (roller)
washer
retaining
arm
ring (RA)
arm
washer
shaft retainer
(roller)
Fig. 1
6 special screw
5 shaft roller assy
2 arm (roller)
7 LOAD SW board
1 tension spring (RA)
2-11. FLOATING BLOCK ASSY
6 floating block assy
7 compression spring (FL)
1 tension spring (KF1)
8 compression spring (FL)
4 Fit lever (D) in the
direction of the arrow.
5 Turn loading ring in the
direction of the arrow.
2 damper (T)
3 damper (T)
13
CDX-M800
2-12. OPTICAL PICK-UP BLOCK
1 P 2x3
4 screw
5 plate spring (feed)
2 sled motor assy
6 shaft (feed) assy
14
3 optical pick-up block
CDX-M800
SECTION 3
PHASE ALIGNMENT
3-1. ARM (A-L) ASSY, ARM (B-L) ASSY
3 arm (A-L) assy
4 type-E stop ring 1.5
2 type-E stop ring 1.5
1 arm (B-L) assy
bracket (L) assy
3-2. CAM (L)
1 Move the arm (B-L) assy in the direction of the
arrow A and the arm (A-L) assy in the direction of
the arrow B fully (full open state).
2 Align the hole (large) on the cam (L) with part C and
install the cam.
4 Turn the cam (L) clockwise and counterclockwise to
verify that both the arms are operated.
3 type-E stop ring 1.5
hole (large)
cam (L)
C
line
A
arm (B-L) assy
arm (A-L) assy
B
15
CDX-M800
3-3. MOTOR BLOCK
1 Turn the cam (L) and position the cam so that part A
does not touch the SW board SW900.
3 PTT 2.6x6
4 PTT 2.6x6
2 motor block
SWITCH board
5 PTT 2.6x6
SW900
cam (L)
A
3-4. ALIGNMENT BETWEEN ARM (A-L) ASSY
AND ARM (B-L) ASSY
1 Input 9V DC to the motor terminal until the cam (L)
stops rotating.
Take care to avoid overload of the motor.
2 Verify that the arm (A-L) assy and arm (B-L) assy
are positioned as shown below (full open).
motor
arm (B-L) assy
+B
DC 9V
GND
arm (A-L) assy
16
CDX-M800
3-5. ARM (A-R) ASSY, ARM (B-R) ASSY
3 arm (A-R) assy
4 type-E stop ring 1.5
2 type-E stop ring 1.5
1 arm (B-R) assy
bracket (R) assy
3-6. CAM (R)
3 type-E stop ring 1.5
1 Move the arm (B-R) assy in the direction of the
arrow A and the arm (A-R) assy in the direction of
the arrow B fully (full open state).
2 Align the hole (large) on the cam (R) with part C and
install the cam.
4 Turn the cam (R) clockwise and counterclockwise to
verify that both the arms are operated.
hole (large)
cam (R)
arm (B-R) assy
A
C
line
B
arm (A-R) assy
5 oil damper
6 screw (P 2x4)
17
CDX-M800
SECTION 4
DIAGRAMS
4-1. IC PIN DESCRIPTIONS
• IC303 M30626FHPGP-052 (US, Canadian model) (SYSTEM CONTROL) (MAIN Board (2/2))
• IC303 M30626FHPGP-053 (AEP, UK, E model) (SYSTEM CONTROL) (MAIN Board (2/2))
Pin No.
Pin Name
I/O
Pin Description
1
SIRCS
I
Remote control data input
18
2
3
FP CTRL
CD SO/TSO
O
O
Front panel open/close speed control signal
CD servo serial data output
4
5
CD SI/TSI
CD CKO/TCKO
I
O
CD servo serial data input
CD servo serial clock output
6
7
BYTE
CNVSS
I
I
L fixed terminal
Flash write-in signal input
8
9
XIN
XOUT
I
O
Sub clock signal input (32kHz)
Sub clock signal output (32kHz)
10
11
RESET
OSC OUT
I
O
CPU reset signal input
Main clock signal output (6MHz)
12
13
VSS
OSC IN
—
I
Ground
Main clock signal input (6MHz)
14
15
VCC1
NMI
—
I
Power supply pin (+5V)
Non maskable interrupt signal input
16
17
CD PACK
DAVN
I
I
CD text pack synchronized signal input
RDS data acquisition detect signal
18
19
BU IN
NS MASK
I
O
Back-up power detect signal
Not used. (Open)
20
21
BEEP
FLW IN
O
I
Beep signal output
OSC frequency shift signal for DC/DC conv.
22
23
24
NCO
SA CLK
TEL ATT
O
O
I
Not used. (Open)
Spectrum analyzer clock signal output
telephone mute detect signal input
25
26
ATT
VOL ATT
O
O
Mute signal output
Electronic volume mute signal output
27
28
I2C CKO
I2C SIO
O
O
Tuner/E-volume BUS clock output
Tuner/E-volume BUS data output
29
30
UNI SO
UNI SI
O
I
SONY BUS data output
SONY BUS data input
31
32
UNI CKO
TUNER ATT
O
O
SONY BUS clock output
Tuner attenuate signal output
33
34
EESIO
EECKO
I/O
O
EEPROM data input/output
EEPROM clock output
35
36
NCO
ADSO1
O
O
Not used. (Open)
Not used. (Open)
37
38
ADSO2
NCO
O
O
Not used. (Open)
Not used. (Open)
39
40
HOLD
AMP DIAG
I
I
Flash write-in signal input
Amplifier diagnosis signal input
41
42
AMP STB
AMP ON
O
O
Amplifier strobe signal output
Not used. (Open)
43
44
TUNER ON
WRI/WR
O
I
Not used. (Open)
Flash write-in signal input
45
46
CD LIMIT
CD D SW
I
I
CD limit detect signal input
CD disc SW detect signal input
47
48
CD PH1
CD INSW/PH2
I
I
CD PH1 detect signal input
CD IN SW/PH2 detect signal input
49
50
PH3
DST SEL1
I
I
CD PH3 detect signal input
Destination select signal input
CDX-M800
Pin No.
51
Pin Name
DST SEL2
I/O
I
Pin Description
52
53
CD LM LO
CD LM EJ
O
O
CD loading motor control signal output
CD eject motor control signal output
54
55
CD RST
CD AO
O
O
CD servo reset signal output
CD servo command/parameter discri. output
56
57
CD STB
CD TSTB
O
O
CD servo data strobe signal output
CD servo text strobe signal output
58
59
CD RFOK
CD XTALEN
I
O
CD servo RFOK signal input
CD servo crystal OSC control signal output
60
61
VCC2
RESET OUT
—
O
Power supply pin (+5V)
Display CPU reset signal output
62
63
VSS
TEST IN
—
I
Ground
Test mode setting detect signal input
64
65
BUS ON
SYS RST
O
O
BUS ON control signal output
System reset signal output
66
67
BUS/AUX
LINK OFF
O
O
BUS/AUX select control signal output
Link OFF control signal output
68
69
ACC IN
ILL IN
I
I
Accessory key ON detect signal input
Ilumination line detect signal input
70
71
RC IN1
NCO
I
O
Rotary commander signal input 1
Not used. (Open)
72
73
CD SELF SW
TU ATT IN
I
I
CD self SW detect signal input
Tuner mute control signal input
74
75
76
CLOSE SW
OPEN SW
I-DET
I
I
I
Front panel close detect signal input
Front panel open detect signal input
Front panel current detect signal input
77
78
MOT–
MOT+
O
O
Front panel open/close control signal output
Front panel open/close control signal output
79
80
ROMC EN
QUALITY
I
I
ROM correction enable signal input
Tuner noise detect signal input
81
82
MPTH
VSM
I
I
Tuner multi-path signal input
S-meter signal input
83
84
SA IN
KEY IN1
I
I
SA data input
Key signal input 1
85
86
KEY IN0
RC IN0
I
I
Key signal input 0
Rotary commander signal input 0
87
88
KEY ACK2
KEY ACK0
I
I
Key acknowledge detect signal input 2
Key acknowledge detect signal input 0
89
90
KEY ACK1
OPEN KEY
I
I
Key acknowledge detect signal input 1
Open key detect signal input
91
92
RAM BU
FLD ON
I
O
RAM reset detect signal input
FL driver power supply ON/OFF signal output
93
94
FL ON
AVSS
O
—
FL power supply ON/OFF signal
Ground
95
96
DISP CE
VREF
O
—
Display CPU chip enable output
A/D converter reference voltage (+5V)
97
98
AVCC
DISP SI/RX
—
I
Power supply pin (+5V)
Display CPU BUS data input
99
100
DISP SO/TX
DISP CKO
O
O
Display CPU BUS data output
Display CPU BUS clock output
Destination select signal input
19
CDX-M800
• IC2 M30833FJGP-066 (DISPLAY SYSTEM CONTROL) (DISPLAY Board)
Pin No.
Pin Name
I/O
Pin Description
1
SYS RST
I
Main chip enable input
2
3
NC
FL DATA3
I
O
Not used. (Open)
FL serial data output
4
5
NC
FL CLK IN
O
I
Not used. (Open)
FL serial clock input
6
7
BYTE
CNVSS
I
I
L fixed terminal
Flash write-in signal input
8
9
NC
NC
O
O
Not used. (Open)
Not used. (Open)
10
11
RESET
XOUT
I
O
CPU reset signal input
Main clock signal output (30MHz)
12
13
VSS
XIN
—
I
Ground
Main clock signal input (30MHz)
14
15
VCC
NMI
—
I
Power supply pin (+5V)
Non maskable interrupt signal input
16
17
NC
NC
O
O
Not used. (Open)
Connecting to pin 20.
18
19
NC
NC
O
O
Not used. (Open)
Not used. (Open)
20
21
NC
LAT
O
O
Connecting to pin 17.
FL data LAT output
22
23
BK
GCP2
O
O
FL BK output
FL GCP2 outpit
24
25
NC
GCP1
O
O
Not used. (Open)
FL GCP1 output
26
27
NC
GCP4
O
O
Not used. (Open)
FL GCP4 output
28
29
GCP3
SYS SO
O
O
FL GCP3 output
Main BUS data output
30
31
SYS SI
SYS CLK
I
O
CPU BUS data input
Main BUS clock input
32
33
NC
FL DAT1
O
O
Not used. (Open)
FL serial data output
34
35
NC
FL CLK
O
O
Not used. (Open)
FL serial clock output
36
37
LCD CE
LCD INH
O
O
LCD driver chip enble output
LCD driver inhibit output
38
39
NC
HOLD
O
I
Not used. (Open)
Flash write-in signal input
40 – 43
44
NC
WRI/WR
O
I
Not used. (Open)
Flash write-in signal input
45 – 59
60
NC
VCC
O
O
Not used. (Open)
Power supply pin (+5V)
61
62
NC
VSS
O
O
Not used. (Open)
Ground
63 – 93
94
NC
AVSS
O
—
Not used. (Open)
Ground
95
96
NC
VREF
O
—
Not used. (Open)
Power supply pin (+5V)
97
98
AVCC
RXD1
—
—
Power supply pin (+5V)
Not used. (Open)
99
100
FL DATA2
FL CLK IN
O
I
FL serial data output
FL serial clock input
20
CDX-M800
4-2. BLOCK DIAGRAM — CD SECTION —
RF AMP,DIGITAL SERVO
DIGITAL SIGNAL PROCESSOR
IC1
OPTICAL PICK-UP
KSS-721A
A
84
C
85
(Page 22)
TUNER
SECTION
B
D
RF
EQ
A
B
82
DSUB CODE
PROCESS
C
I-V
CONV.
D
LOUT
16
ROUT
12
D/A
CONV
EFM
DEMOD
83
FORCUS
ERROR
I/F
E
E
87
F
86
PD
97
LD
DRIVE
Q1
PD
SERVO
CTL
A+5V
XTALEN
62 63 64 65
23
FOCUS/TRACKING COIL DRIVE,
SLED/SPINDLE/LOADING MOTOR DRIVE
IC2
FCSFOCUS
COIL
FCS+
TRK+
TRACKING
COIL
TRK-
15
16
17
18
FOCUS
COIL
DRIVE
TRACKING
COIL
DRIVE
26
23
M
M901
(SPINDLE)
M
M903
(LOADING)
M
SL-
SLED
MOTOR
DRIVE
5
12
SPINDLE
MOTOR
DRIVE
6
9
LD+ 10
LOADING
MOTOR
DRIVE
SL+
SP+
SP-
13
14
11
SYSTEM CONTROL
IC303 (1/3)
3 CD TSO
4 CD TSI
5 CD TCKO
57 CD TSTB
55 CD A0
54 CD RST
2
58 CD RFOK
9
59 CD XTAL EN
24
X1
16.9344MHz
FD
SW5
(DOWN)
SW2
(SELF)
TD
SW3
(DISC IN)
M902
(SLED)
A
MD
SD
98
TD
OSC
LD
PACK
52
TSTB
56
TSCK
55
TSI
54
SI
8
SO
7
SCK
6
STB
5
AO
4
RST
3
RFOK
APC
FD
LD
F
TRACKING
ERROR
CDL
R-CH
SW4
(LIMIT)
SD
46 CD D SW
72 CD SELF SW
48 CD IN SW
45 CD LIMIT
MD
• Signal path
LD-
1
LOAD
52 CD LM LO
EJECT
2
53 CD LM EJ
:CD
• R-ch is omitted due to
same as L-ch.
21
21
CDX-M800
4-3. BLOCK DIAGRAM — TUNER SECTION —
PJ401
–1
L
ELECTRONIC VOLUME
IC401
Q408
CD
SECTION
A
(Page 21)
CDL
4 PDL
42 MDL
CN503
(ANTENNA)
–2
R
R-CH
–5
L
–6
R
R-CH
–3
L
–4
R
LF 25
32 AC OUT L
TUNER UNIT
TUX501
R-CH
Q171
31 AC IN L
OUT LR 24
1 ANT
L 4
R 3
40 AML
Q181
AM
12 SDA
13 SCL
OUT SW 17
SA CLK 14
SA OUT 16
15 MUTE
MUTE DRIVE
Q401,402
POWER AMP/POWER SUPPLY
IC201
FL
16 FM DET
4 OSCD
5 OSCI
12
SYSTEM CONTROL
IC303 (2/3)
9
FL–
3
2
RDS DECODER
IC502
SDA 9
SCL 10
DAVN 8
26 VOL ATT
SA IN 43
28 I2C SIO
27 I2C CKO
SA CLK 23
BUS/AUX 66
17 DAVN
X501
4.3MHz
QUALITY 5
80 QUALITY
TU MUTE 7
MUTE CONDITION 8
S-METER 6
32 TUNER ATT
73 TU ATT IN
82 VSM
ATT
BEEP
AMP STB
AMPDIAG
SDA 17
SCL 16
33 EESIO
34 EECKO
11
10
2 SDA
RL–
7
4 SCL
16
22 STB
25 DIAG
+10V
AU+8V
XOUT 9
XIN 8
RL+
9
RL
25
20
41
40
OSCOUT 11
EEPROM
X301
32.768kHz
+5V
DR+6V
A+5V
AU+5V
X302
6MHz
OSCIN 13
Q103
D+5V
34
30
37
33
DISP;B
AU8V
U-COM
MECHA
31 SERVO
R-CH
AU +8V
+5V REG
Q501
TU+5V
ILL IN 69
: AM/MW
ACC DET
Q102
ACC IN 68
: CD
TEST IN 63
19
17
VP 35
18
16
13
7
F901
BATT
ATT
ILL
ACC
15
TEST
• R-ch is omitted due to
same as L-ch.
22
AMP REM
ANT REM
VP1 20
14
: FM
FR+
FR–
RR+
RR–
VP2 6
BATT
ILLUMI
CHECK
Q907
4
12
3
11
5
6
SW1 29
SW2 27
TEL ATT 24
• Signal path
AUDIO OUT
REAR
CNP101
1
FL+
5
AEP,UK,E MODEL
RDS 9
AUDIO OUT
FRONT
CN401
(SUB OUT(MONO))
Q470
SDA 14
SCL 13
BUS AUDIO
IN
22
CDX-M800
4-4. BLOCK DIAGRAM — DISPLAY SECTION —
BUS INTERFACE
IC301
CNP102
(BUS CONTROL IN)
6
5
4
30 UNI SI
8
DATA
8
SYSTEM CONTROL
IC303 (3/3)
3
2
1
CLK
9
29 UNI SO
11
31 UNI CKO
BUS
ON
12
64 BUS ON
RESET
13
D513
4
7
1
BATT
2
BATT
3
BATT
CHECK
65 SYSRST
10
18 BU IN
BATT DET
Q101
BATT
LCD DRIVER
IC1
LED CONTROL LED SW1
105
Q907,908
DIMMER
LCD2
INH
CF
CLK
DATA
13 XIN
SYS CE
37 LCD INH
SYS SO
36 LCD CE
SYS SI
35 FL CLK
SYS CLK
33 FL DAT1
117
118
119
120
KEY IN0 85
KEY IN1 84
KEY IN
MATRIX
AEP,UK,E MODEL
RC IN1 70
RC IN0 86
CNJ101
(REMOTE IN)
IC302
1 RESET 2
RESET 10
11 XOUT
X301
30MHz
IR
7 RECEIVE 1
IC503
KEY ACK2 87
KEY ACK0 88
KEY ACK1 89
SUB SYSTEM CONTROL
IC2
SEG1
1
I
I SEG95
103 COM1
I
COM8
1
29
30
31
CNVSS 7
95
98
99
100
DISP CE
DISP SI/RX
DISP SO/TX
DISP CKO
DIMMER
CONTROL
Q905
FL 900
GCP
FL CONTROL
IC301
11
5
4
2
1
T800
S932
(RESET)
7 CNVSS
LAT
BK
FL DAT2
FL DAT3
BATT
23
25
27
28
GCP2
GCP1
GCP4
GCP3
DC-DC CONVERTER
IC800
FL POWER
CONTROL
Q801,802
1
SW501
RESET
MOTOR+B REG
3
IC306
2
MT+B
M601
(OPEN/CLOSE9
MOT+ 78
11
MOT- 77
6
MOTOR
DRIVE
IC307
12
MT+B
VREF
CONTROL
Q306,307
FP CTRL 2
I-DET 76
OPEN SW 75
CLOSE SW 74
93 FL ON
FL+
FLFLVDD
21
22
99
3
+5V
RAM BU 91
104 106
LED CONTROL LED SW2
Q903,904
D70
IR
7 RECEIVE 1
IC62
SIRCS 1
6
I-DET
Q305
SW900
(OPEN/CLOSE)
LED CONTROL
Q503,504
BATT
OPEN KEY 90
23
23
S931
(OPEN)
7 I-DET
IC308
D512
(DISC IN)
3
3
14
16
CDX-M800
4-5. CIRCUIT BOARDS LOCATION
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
IN SELF SW board
SL SW board
for schematic diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
%
: indicates tolerance.
f
•
: internal component.
• C : panel designation.
Note:
Note:
The components identi- Les composants identifiés par
fied by mark 0 or dotted une marque 0 sont critiques
line with mark 0 are criti- pour la sécurité.
Ne les remplacer que par une
cal for safety.
Replace only with part piéce portant le numéro
spécifié.
number specified.
SERVO board
SWITCH board
tuner unit
(TUX501)
LOAD SW board
• A : B+ Line.
• Power voltage is dc 14.4V and fed with regulated dc power
supply from ACC and BATT cords.
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : FM
f : AM/MW/LW
J : CD
• Abbreviation
CND : Canadian model
MAIN board
DISPLAY board
SUB board
• Waveforms
— Servo Board —
• Waveforms
— Main Board —
• Waveform
— Display Board —
(MODE: CD PLAY)
(MODE: FM)
(MODE: FM)
1
1
1
2Vp-p
3.2Vp-p
16.9344MHz
IC1
wd
1.5Vp-p
30MHz
4.3MHz
(XTAL)
IC502
2
4
(OSCD)
IC2
qa
(XOUT)
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
2
1.8Vp-p
5Vp-p
3.2msec
IC1
ts
32.768kHz
(PACK)
IC303
3
9
for printed wiring boards:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
x
: parts mounted on the conductor side.
a
•
: Through hole.
•
: Pattern from the side which enables seeing.
(The other layer’s patterns are not indicated.)
• Abbreviation
CND : Canadian model
(XOUT)
3
3.6Vp-p
1.2Vp-p
6MHz
IC1
uj
(RFO)
IC303
qa
(OSCOUT)
4
0V
Approx. 100mVp-p
IC1
oa
(FEO)
5
0V
Approx. 100mVp-p
IC1
od
Parts on the pattern face side seen from the
pattern face are indicated.
Parts on the parts face side seen from the
parts face are indicated.
(TEO)
24
24
CDX-M800
• Refer to page 24 for Waveforms.
4-6. SCHEMATIC DIAGRAM — CD MECHANISM SECTION — • Refer to page 36 for IC Block Diagram.
CN2
TP8
C20
C19
TP77
R29
TP78
R30
R3
R26
C23
C24
R9
C43
C3
C4
C6
TP89
TP79
TP80
C35
R8
C5
TP22
C18
C1
TP88
TP9
TP23
TP24
TP25
Q1
C14
TP81
TP82
TP45
TP10
TP83
TP84
C13
TP44
TP43
C11
TP42
TP41
R5
TP40
TP39
TP38
TP37
SW4
TP7
C15
IC1
TP46
C10
TP36
C38
TP12 C9
TP11
CN13
CN3
C8
TP85
TP35
TP34
M902
C16
C36
M901
IC B/D
C44
C25
TP92
C29
CN1
C17
FB1
C40
X1
R18
TP75
TP59
C45
C26
C27
C41
TP1
TP5
SW5
C34
TP61
TP76
TP60
R19
R20
TP6
R17
TP74
TP58
TP73
TP57
TP72
TP56
TP71
TP55
TP70
TP54
TP69
TP4
TP2
SW2
TP53
TP68
TP30
TP32
TP52
TP66
SW3
TP3
R7
R15
TP21
TP51
R12
R22
TP18
TP50
R14
TP64
TP49
R10
C22
IC2
R21
C21
TP90
C30
TP17
TP27
TP20
TP16
TP29
TP26
TP19
TP28
TP87
M903
TP86
Note:
• Voltage is dc with respect to
ground under no-signal conditions.
no mark : CD PLAY
25
25
TP91
TP48
TP63
TP47
TP62
C37
IC B/D
(Page 31)
CDX-M800
4-7. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 24 for Circuit Boards Location.
12
11
10
9
8
7
6
5
4
3
2
1
A
2
13
CN
14
B
C
D
E
F
G
H
I
J
26
26
CDX-M800
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
TP63
R30
C5
C1
B
TP78
TP77
TP7
TP62
TP82
C4
R29
TP48
C43
TP59
CN1
TP71
TP70
R5
R8
C24
TP22
TP24
TP25
C25
TP23
R19
IC1
C34 C45
C27
TP61
R9
C41
C40
TP72
TP58
C20
C19
C17
FB1
R17
E
C16
R18
TP56
TP89
TP76
TP74
(Page 29)
SW2
TP88
C29
R21
D
C15
C8
TP51
SW5
TP10
C10
C23
C9
C18 C13
TP8
TP52
SW3
TP12
C11
R22
TP64
TP83
TP81
TP11
C14
TP50
TP47
TP9
R26
R3
TP60
C6
C
TP79 C3
TP80
TP66
TP84
Q1
TP69
X1
TP68
C35
TP46
C38
TP92
C26
TP45
TP37
TP41
TP39 TP40
C44
R20
TP35
TP34
TP36
TP49
TP57
F
C36
TP38
TP75
SW4
TP44
TP43
TP42
TP18
TP21
TP85
TP55
TP30
TP32
TP73
TP6
R7
R10 R12
R15
TP53
TP91
TP86
C22
TP87
IC2
TP26
TP4
TP29
TP19
C30
TP20
TP54
TP5
C37
C21
H
TP90
R14
G
TP28
TP17 TP16
TP27
I
TP3
TP2
CN3
TP1
J
27
27
CDX-M800
4-8. PRINTED WIRING BOARDS — MAIN SECTION — • Refer to page 24 for Circuit Boards Location.
14
13
12
11
10
9
8
7
6
5
4
3
2
1
A
B
C178
R275 R175
C218
C219
C288
R285
C242
C188
R185
Q171
Q271
C
Q181
Q281
R174
C142
R142
R242
C207
R284
C206
R204
R205
R206
R184
R243
R143
R920
R433
R435
R429
D909
C903
R922
R431
R112
R921
Q470
D
R407
R929
R182
R272
R172
R282
Q907
E
R478
R320
C428
C426
C423
R419
R421
C430
C526
C525
C528
R518
R416
C521
R415
R414
IC401
F
C520
IC502
R519
C421
C424
R425
C527
R418
R417 C427
C429
R422
JR300
C431
R420
C416
IC301
R901
C417
R346
): SIDE B
R903
G
C810
R902
R906
D904
T800
R910
R907
C809
IC306
C342
X302
C323
C322
IC307
R372
R338
R378
R373
C335
R318
IC303
R325
R364
R368
R377
C336
R369
D303
H
IC800
D302
L800
C802
I
JR301
R915
D826
CNP909
D831
D829
D827
D828
D808
D825
D810
D819
C318
R324
JR302
R335
C319
D305
C320
R319
Q305
R326
R350
R351
E-10
E-9
F-9
C-4
C-3
C-4
C-3
H-8
I-9
H-9
G-10
F-5
E-5
E-2
D-3
E-1
I-4
H-4
D-8
F-11
F-10
E-10
C278
R203
R274
B-6
F-9
H-8
H-8
H-10
I-10
I-10
F-3
F-2
H-5
C339
(
Location
I-8
I-4
G-7
F-10
I-8
D-8
C310
• Semiconductor Location
Ref. No. Location
Ref. No.
(D832)
(D101)
E-10
(D843)
(D102)
E-10
D904
(D103)
E-10
(D905)
(D104)
E-10
(D907)
(D105)
E-10
D909
(D106)
C-9
(D109)
D-9
(IC201)
(D110)
B-8
IC301
(D111)
D-8
(IC302)
(D112)
B-8
IC303
(D113)
D-7
IC306
(D114)
D-8
IC307
(D115)
C-8
(IC308)
(D116)
D-8
IC401
(D117)
C-8
IC502
(D118)
F-9
IC800
(D119)
F-9
(D120)
E-8
(Q101)
(D121)
E-8
(Q102)
(D122)
B-2
(Q103)
D302
H-9
Q171
D303
H-10
Q181
D305
I-9
Q271
(D401)
E-5
Q281
(D501)
E-2
(Q301)
(D802)
I-3
Q305
(D803)
I-3
(Q306)
(D804)
H-2
(Q307)
(D805)
H-2
(Q401)
(D806)
H-3
(Q402)
D808
J-7
(Q408)
D810
J-7
Q470
D819
J-6
(Q501)
(D820)
I-4
(Q801)
D825
J-7
(Q802)
D826
J-5
Q907
D827
J-7
(Q914)
D828
J-7
(Q915)
D829
J-7
(Q916)
D831
J-6
J
(Page 34)
28
28
CDX-M800
1
2
3
4
5
6
7
8
9
10
11
12
13
PJ401
A
CNJ101
C199
CN904
CN903
TH100
JW1
C104
D116
D114
C226
JW2
C103
D113
C221
C223
JW11
C273
C173
C283
C183
C503
C506
D117
D115
JW14
R502
R103
D106
C442
C505
C101
JW8
R440 R443
JW7
R442
JW9
CN401
C
R441
R408
R446
R410
CN503
F901
D112
D110
R445
TUX501
IC201
R439
FB102
CNP101
C215
D122
FB101
R444
B
JW10
CNP102
D109
BATT
L101
R105
R110
JW17
D118
D119
Q915
R912
C930
L302
R317
C305
R322
R307
C312
R323
R911
R308
C334
R367
Q307
C313
CNP902
Q301
IC302
R374
R805
X301
C807
SW900
R366
Q306
C338
R375
R334
C315
R343
R370
R812
C823
R833
R811
R356
R327
R845
D820
D843
SW900
C341
R332
R333
D802
R866
IC308
R328
R301
C316
R808
C317
Q801
C321
R806
R804
R809
R801
R800
C803
D803
I
Q802
R365
R336
R361
R376
R807
D805
R803
H
D806
R357
CNP805
D832
D907
J
(Page 32)
29
29
C311
D804
R337
R371
R341
R339
C523
C420
R305
R310
(Page 27)
R309
C337
R520
R306
US,CND,E model
JW18
R311
Q103
R302
R312
X501
R316
Q914
D905
C901
C303
C308
C425
R304
R909
C422
D104
D101
R949
R950
R109
R313
C418
R101
R102
JW3
JW6
L301
R104
Q102
C928
R908
C419
CN601
Q916
D102
D103
C309
C433
C522
D105
R106
R340
C435
F
L303
C304
FB303
FB501
JW16
C306
C301
Q401
CNP301
FB302
C434
C524
C432
FB301
C402
C401
Q402
Q101
D120
C307
D401
R424
R521
JW15
R401
C302
R505
D121
R108
L401
R303
E
R107
C201
Q408
C102
R111
R201
C501
R501
C203
C202
D501
Q501
JW5
C204
R202
JW13
C212
C443
C214
C502
R504
JW12
R402
G
C105
D111
R503
JW4
D
AEP,UK model
14
CDX-M800
4-9. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) —
• Refer to page 24 for Waveform.
• Refer to page 36 for IC Block Diagrams.
C278
R440
R444
R439
R443
C288
R442
R446
C242
R441
R445
C206
C207
R203
C178
C212
R204
PJ401
C188
C214
C199
C142
C215
R242
R142
D122
C204
C203
R243
R143 R408
R410
R202
Q402
R401 D401
C202
Q470
C402
R201
R407
C442
CN401
C401
Q401
R272 R429
C273
R274
Q271
Q281
R282 R431
R205 C218 R206 C219
D121
D120
R172 R435
IC201
C221
C223
C283
CN503
R275
R285
C506
C505
C503
C201
R284
C173
C226
R174
R502
R175
Q171
IC B/D
Q181
R182 R433
CNP101
C183
R185
TUX501
R184
R503
R504
L401
C417
C418
R505
C420
C419
C416
R424
Q408
C423
F901
C421
R425
C433
C422
C435
Q501
D110
D111
D112
D113
D114
D115
D116
D117
D118
C104
D119
C105
C424
L101
IC401
C501
IC B/D
C434
FB501
C425
R921
C502
R414
C426 R415
D109
D501
R501
C103
C524
R920
C526
C527
C525
R416
R103
D909
D106
C528
R521
R417
Q907
R111
R922
C427
Q103
R110
C903
R109
Q102
R418
C428
R108 C102
R106 R104
C429
R422
R105
R421
R107
IC502
IC B/D
C432
R112
R419
R929
R420
C430
C431
R478
C443
R402
R518
C521
R519
R520
X501
C523
C520 C522
(Page 31)
Note:
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
(
) : AM/MW/LW
<
> : CD PLAY
30
30
CDX-M800
• Refer to page 24 for Waveform.
4-10. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 36 for IC Block Diagrams.
(Page 30)
C304
L303
D105
D104
R102
(Page
25)
FB301
IC301
CNP102
TH100
R101
C101
R303
CNP301
C307
C306
D101
L301
Q101
C308
C301 C302
JR300 R320
C310
FB303
FB302
D103
D102
C303
IC B/D
C309
R908
R909
C305
IC B/D
Q305
R302
R368
R369
D302
R338
R318
R313
C337
R339
C335
Q306
D303
IC306
IC308
Q307
IC307
R334
R337
C338
R336
C336
R371
R340
R341
C321
R370
C339
C341
C342
C334
R377
R306
D901
R328
R327
M601
R373
R325
R310
R309
R308
R911
R316
R903
R901
CNP902
Q801
R808
SW900
D832
R372
R307
R912
R902
R809
R361
L800
Q802
CNP805
R907
JR301
R906
R312
R335
R311
R811
R866
IC B/D
JR302
IC800
D805
T800
C318
R366
C802
(Page 33)
D804
R346
R324
R365
IC303
D803
D806
US, CND
AEP, UK, E
R319
C803
R801 R800
D802
CN601
R805
D826
D829
R803
CNP909
R323
R322
D904
C313
R305
R317
R304
R357
X301
R378
X302
R301
C317
R364
R326
D907
C320
D305
R910
R333
R356
Q914
R950
C322 C323 C315C316
R376
Q915
C901
R949
(Page 35)
Q301
R374
D825
D905
R375
Q916
C928
C312
C930
R367
C311
R351
R350
IC302
C319
R804
R806
C809
D831
C810
D827
L302
R915
C807
D828
R807
D843
D808
D820
C823
D810
D819
R845
R833
R812
R332 R343
FB102
CNJ101
FB101
31
31
Note:
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
(
<
∗
) : AM/MW/LW
> : CD PLAY
: Impossible to measure
CDX-M800
4-11. PRINTED WIRING BOARD — SUB SECTION — • Refer to page 24 for Circuit Boards Location.
2
1
3
4
5
6
7
8
9
10
11
12
13
14
A
C535
C536
Q503
D512
R533
R531
R536
C539
C533
Q504
D514
C537
R538
C540
R509
C538
D506
R532
R534
D511
D507
B
FB503
SW501
IC503
C
(Page 29)
D
CN501
E
D513
F
C535
CN502
G
• Semiconductor
Location
Ref. No.
D506
D507
D511
D512
D513
D514
Location
B-10
B-6
C-8
C-8
E-13
C-10
IC503
B-13
Q503
Q504
C-9
B-10
32
32
CDX-M800
4-12. SCHEMATIC DIAGRAM — SUB SECTION — • Refer to page 37 for IC Block Diagrams.
CN502
Q503
R532
R531
R534
R533
D511
Q504
D512
SW501
D513
D514
C536
(Page 31)
R536
R538
CN501
C533
C537
R509
C535
FB503
C538
C539
D506
C540
D507
IC B/D
IC503
Note:
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
33
33
CDX-M800
4-13. PRINTED WIRING BOARD — DISPLAY SECTION — • Refer to page 24 for Circuit Boards Location.
2
1
3
4
5
6
7
8
9
10
11
12
13
14
FL900
A
R971
C905
LED931
C908
R947
FL919
FB901
X301
FB905
FB904
FB923
FB921 C960
C961 C970
FB971
R954
C964
R956
R992
Q903
Q904
R951
R929
IC301
R944
R970
FB917
FB906
R967
IC1
R991
R982
R984
FB902
R965
FB925
R939
FL924
R985
C910
R964
C963
FL910
FB909
FB908
FB907
FB922
R968
C911
C902
R969
C
FB911
FB915
FB916
R986
D908
FB912
IC2
R987
FB60
C903
IC62
C912
FB913
C909
FB920 FL918
C904
D902
C907
C983
C914
C901
D901
R916
S931
B
S909
C973
FB914
R981
C913
R940
R994
C962
FB926
R941
R906
R945
LED909
R988
R928
S932
FB903
D
(Page 28)
E
S916
Q905
LED901
R959
6
LED
905
906
R980
LED956
R942
R950
R936
S9
15
S922
LED916
LED955
LE
LED917
D9
15
R990
S914
LED958
S918
S904
S907
G
R920
R911
LED957
R912
R918
R935
R917
LED
R919
S917
R979
R978
D70
R913
S901
R962
F
LED922
CNP908
S90
5
S90
R921
LCD2
R953
Q908
S90
Q907
LED903
902
908
LED
8
9
S 0
2
S9
S919
LED919
LED920
R946
R915
S920
• Semiconductor Location
Ref. No.
D70
D901
D902
D908
Location
F-2
B-1
B-4
B-10
IC1
IC2
IC62
IC301
C-8
B-6
C-2
C-7
Ref. No.
LED901
LED902
LED903
LED905
LED906
LED908
LED909
LED911
LED912
LED913
Location
F-2
H-2
H-1
F-3
F-4
H-4
A-13
H-14
H-12
H-12
Ref. No.
LED915
LED916
LED917
LED919
LED920
LED921
LED922
LED931
LED955
LED956
Location
F-12
F-12
F-11
H-5
H-9
H-11
F-13
A-2
F-9
F-6
21
21
Ref. No.
LED957
LED958
Location
G-4
G-13
Q903
Q904
Q905
Q907
Q908
C-11
C-10
F-4
H-2
H-2
34
34
R914
R925
LE
LED912
D9
13
R922
R961
D9
R955
R960
R901
R909
R952
H
LED
R907
S903
R957
R902
R958
LE
R908
R910
S9
S912
R923
S911
13
LED911
CDX-M800
• Refer to page 24 for Waveform.
4-14. SCHEMATIC DIAGRAM — DISPLAY SECTION — • Refer to page 37 for IC Block Diagrams.
R946
R950
R936
Q903
R952
R945
R951
R954
R953
R956
R958
R955
R960
R957
R961
R959
R962
R929
LED917
LED911
LED921
LED908
LED901
LED916
LED913
LED920
LED902
LED905
LED915
LED919
LED903
LED906
LED955
LED957
R928
LED956
LED912
Q905
Q904
LED958
R990
R935
CNP908
LED922
S932
IC62
R994
Q907
IC B/D
C914
D70
S931
R901
R964
R965
R967
R988
R968
FB60
R902
C902
LED931
(Page 31)
C983
LED909
C912
Q908
D901
D902
C901
D908
C904
R969
C903
C905
FB914
IC1
C913
C907
C908
C909
C910
FB926
R941
R942
R940
S901
IC2
R913
R912
S902
S911
S903
S912
S904
S913
S905
S914
S906
S915
S907
S916
R923
FB909
FB908
FB907
FB906
FB905
R922
FB916
R910
R909
R982
FL910
FB915
R911
C911
R981
R980
R979
R978
FB913
FB912
FB911
R987
R986
R985
R984
R921
R992
R920
S909
S918
S919
S920
S921
R917
FB904
FB903
C961
FB922
FB921
C960
X301
FB920
S917
R939
C970
R947
R944
FB971
IC301
R916
IC B/D
R915
C963
R914
C973
C964
R925
C962
R906
S908
R918
FL918
FB917
R907
FB923
R970
FB901
FB902
FB925
FL919
R919
FL924
R991
R908
S922
R971
LCD2
FL900
35
35
Note:
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
CDX-M800
4-15. IC BLOCK DIAGRAMS
SD
TD
FD
AGND
ATEST
TEST1
TEST0
DGND
TSTB
TSCK
TSI
TSO
PACK
DVDD
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
MICROCOMPUTER INTERFACE
CD-TEXT DECODER
EFM
D/A
EQ1 79
FD/TD/SD/MD
CONTROLLER
48 C2D1
6
PREVCC
7
POWVCC12
(CH1.CH2)
41 LOCK
POWVCC
8
VOL–
9
+
+
+
+
39 TSOI
TE2 94
DE-EMPHASIS CIRCUIT
TRACKING
REGISTER
FOCUS
REGISTER
TEO
AGND 96
OCTUPLED
OVERSAMPLING DIGITAL FILTER
COMPARATOR
PD 97
NOISE SHAVER
VO2+ 12
VO1– 13
LEVEL
SHIFT
VO1+ 14
17 VO3+
10k
10k
–
10k
–
LEVEL
SHIFT
LEVEL
SHIFT
–
10k
18 VO3–
10k
10k
10k
32 SCKO
31 SCKIN
LEVEL
SHIFT
–
10k
10k
–
10k
33 LRCKIN
10k
10k
–
+
FEO
TEC 95
MIRENV
35 HOLD/WDCK
10k
16 VO4–
+
MIRR
VO2– 11
34 LRCK
OUTPUT PROCESSOR
A3T
TEO 93
RFENV
36 TX
+
A/D CONVERTER
FOK
TE- 92
37 DGND
+
FEO 91
D/A
INTERFACE
CIRCUIT
19 GND
VOL+ 10
+
DIGITAL
AUDIO
INTERFACE
DEFECT
COMPARATOR
DEFECT
20 POWVCC
38 C16M
SWITCH
FE- 90
21 MUTE
15 VO4+
–
REFOUT 89
CH1-4
MUTE
+
CLV
PROCESSOR
AVDD 88
22 OPOUT3
POWVCC34
(CH3,CH4)
40 DVDD
EFM
E 87
24 OPIN3+
23 OPIN3–
–
–
F 86
25 OPOUT4
PREVCC
(PRE.LOADING)
42 RFCK
TIMING GENERATOR
ROM
DECODER
SVROM
5
IN2
POWER
SAVE
–
RF
AMP BLOCK
D 85
SVCRAM
MULTIPLIER
IN1
44 PLCK
43 MIRR/WFCK
SVDRAM
TEOFS
4
–
DIGITAL PLL
EFM DEMODULATOR
FEOFS
B 84
PS
27 OPIN4+
26 OPIN4–
–
X3
47 C1D2
45 DGND
ADDER
C 83
3
46 C1D1
AGND 81
A 82
LDCONT
LOADING PRE
FWD REV
+
AUTO GAIN
CONTROLLER
RF- 80
SUB-CODE PROCESSOR
16K
SRAM
MEMORY
PROCESSOR
49 C2D2
2
–
EQ2 78
REV
28 BIAS
16k
COMPARATOR
RFO 77
50 C2D3
ERROR
CORRECTION
PROCESSOR
EFM
1
+
AGCI 76
FWD
+
MD
67
+
7F DAC0
68
16k
7C DAC1
69
16k
7D DAC2
70
7.5k
7E DAC3
71
7.5k
AVDD
72
7.5k
EFM
73
–
ASY
74
16k
C3T
75
7.5k
RFI
IC2 BA5810FP-E2 (SERVO Board)
AGCO
IC1 µPD63711GC-8EU (SERVO Board)
10k
10k
10k
30 DOUT
29 DIN
NOISE SHAVER
LD 98
28 FLAG
OUTPUT BUFFER OUTPUT BUFFER
27 EMPH
PN 99
MICROCOMPUTER INTERFACE
SCF
26 DVDD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
DGND
RFOK
RST
A0
STB
SCK
SO
SI
XTALEN
DVDD
DAVDD
ROUT
DAGND
REGC
DAGND
LOUT
DAVDD
R+
R–
L–
L+
XVDD
XTAL
XTAL
XGND
OSC
CIN
SCOUT
VREF
MPX
VSSA
VDDA
AFIN
MAD
PSWN
IC301 BA8270F (MAIN Board (2/2))
LVIN
IC502 SAA6588T (MAIN Board (1/2))
20
19
18
17
16
15
14
13
12 11
PAUSE
DETECTOR
POWER SUPPLY
& RESET
MULTI
PATH
DETECTOR
57kHz
8th ORDER
BAND-PASS FILTER
CLOCKED
COMPARATOR
BUSON 1
RST 2
BATT 3
BUS ON
SWITCH
RESET
SWITCH
BATTERY
SWITCH
GND 1
14 VCC
NC 2
RST
BUSON
CLK-IN
B/U-C
5
CLOCK
RDS/RDBS
DEMODULATOR
RDS/RDBS
DECODER
CLK 4
VREF 5
DATA 6
I/O
4
POWER
SAVE
CLOSE 6
GND 7
DATA
NC 8
15 NC
14 OUT2
13 NC
CURRENT LIMIT,
THERMAL LIMIT,AND
UNDERVOLTAGE SHUTDOWN
DRIVER
STAGE
LOGIC
12 VREF
11 OPEN
NC 7
CLOCK
INTERFACE
REGISTER
DRIVER
DRIVER
M BATT 4
VCC 5
IC800 LM2577SX-ADJ (MAIN Board (2/2))
16 RNF
OUT1 3
13
12
11
10
SIGNAL QUALITY
DECODER
4
IC307 BA6288FS (MAIN Board (2/2))
CONTROL
LOGIC
AVDD 100
52kHz
OSCILLATION
TSD
∑
9 NC
9 DATA IN
8 DATA OUT
SOFT
START
6
7
8
9
10
36
36
TCON
OSCO
OSCI
VSSD
VDDD
DAVN
SDA
SCL
3
4
5
VDD
5
2
SWITCH
4
1
GND
3
2.5V
REGULATOR
CURRENT
SENSE
REGISTOR
ERRIN
1 2
MRO
MPTH
IIC BUS SLAVE
TRANSCEIVER
1.25V
REF.
ERROR
AMP
ERROUT
OSCILLATOR
& CLOCK
AMP
CURRENT
SENSE
VOLTAGE
COMPARATOR
DATA
TEST
CONTROL
CORRECTIVE
RAMP VOLTAGE
10 NC
CDX-M800
IC201 TDA8588J/N1 (MAIN Board (1/2))
TAB 1
2 SDA
FL- 3
I2C BUS
4 SCL
FL
FL+ 5
6 VP2
RL- 7
RL
8 PGND3
RL+ 9
10 SVR
MUTE
IN_RL 11
SGND 13
12 IN_FL
14 IN_FR
MUTE
PROTECTION
DIAGNOSTIC
IN_RR 15
16 ACGND
VP
RR+ 17
RR
18 PGND2
RR- 19
20 VP1
FR+ 21
STANDBY
MUTE
FR
FR- 23
22 STB
CHIP DETECT
DIAGNOSTIC
24 PGND1
BATTERY
DETECTION
DIAG 25
TEMPERATURE
PROTECTION
ENABLE
LOGIC
26 RST
SW2 27
SWITCH
SW1 29
SWITCH
28 CRES
REGULATOR
30 AU8V
SERVO 31
MECHA 33
32 GND
34 DISP+B
VP 35
REFERENCE
VOLTAGE
U-COM 37
36 CBU
LOADDUMP
PROTECTION
REGULATOR
BACK-UP
SWITCH
IC503 RRX9000-0601 (SUB Board)
IC62 RRX9000-0601 (DISPLAY Board)
VIN
16
GND A
15
INPUT
SLAGE
VIN
14
INS GND VCO NC
12 11 10 9
VAGC
13
320kHz
320kHz
/500kHz
NOISE
SUPPRESSION
PULSE
COUNTER
AGC
PULSE
FORMER
BANDGAP
REFERENCE
1 2
LIN GND
3
VSTAB
4
VCC
5
NC
6
NC
7
VPO
8
NC
37
CDX-M800
NC
ACOUTR
ACINSW
ACOUTSW
ACOUTL
ACINL
VREFOUT
VDD
AC2INL
AC2OUTL
FILOL
OUTLF
OUTLR
33
32
31
30 29
28 27 26
25
24 23
HIGH PASS
FILTER2
MIXER
NC
ACINR
IC401 TDA7416 (MAIN Board (1/2))
SOFT STEP
FADER
34
35
36
37
SOFT STEP
FADER
HIGH PASS
FILTER
SUB
WOOFER
FILTER
MIXER
22 OUTRF
SOFT STEP
FADER
21 OUTRR
7 BAND
EQUALIXER
SOFT STEP
FADER
MAIN
VOLUME
HIGH
PASS
FILTER2
SOFT STEP
FADER
SOFT
MUTE
20 AC2INR
19 AC2OUTR
18 FILOR
17 OUTSW
16 SAOUT
15 MUTE
ZERO
CROSS
LOUDNESS
SPECTRUM
ANALIZER
14 SAIN
IN-GAIN
FADER
INPUT
MULTIPLEXER
1 2 3 4 5
6 7
8
9 10 11
NC
GND
NC
POWER
SUPPLY
MIC
40
41
42
43
44
REAR
SELECTOR
NC
PDR+
AML
AMR
MDL
MDR
AUXL
MAIN
SOURCE
SELECTOR
NC
NC
AUXR
PDL+
PD-
CREF 38
NC 39
IC301 TC74VHC32FT(EL) (DISPLAY Board)
1A 1
1B 2
1Y 3
2A 4
2B 5
2Y 6
GND 7
38
14 VCC
13 4B
12 4A
11 4Y
10 3B
9 3A
8 3Y
II2CBUS
13 SCL
12 SDA
CDX-M800
SECTION 5
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
• Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
R
R
Parts Color Cabinet’s Color
• Accessories are given in the last of this
parts list.
• Abbreviation
CND: Canadian model
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
5-1. CHASSIS SECTION
10
9
8
#1
#2
MG-393XC-121//K
not supplied
#1
7
3
4
6
5
#1
A
1
not supplied
A
Ref. No.
#2
2
Part No.
Description
Remark
1
1
2
3
4
X-3382-819-1
X-3382-825-1
1-783-268-11
1-687-950-11
3-232-857-01
PANEL (CD) SUB ASSY, SUB (US,CND)
PANEL (CD) SUB ASSY, SUB (AEP,UK,E)
CABLE, FLAT (FFC) 11P
SUB BOARD
SHEET (SUB PANEL), ELECTROSTATIC
5
6
7
3-248-826-01 COVER (FLEXIBLE)
3-230-516-01 SPRING (FLEXIBLE), TENSION
3-045-756-01 SCREW (PANEL)
7
Ref. No.
8
Part No.
Description
Remark
9
10
#1
1-776-207-72 CORD (WITH CONNECTOR) (POWER)
(US,CND,E)
1-776-527-71 CORD (WITH CONNECTOR) (ISO) (POWER)
(AEP,UK)
3-223-913-11 LABEL (OP CAUTION) (AEP,UK,E)
3-248-858-01 BRACKET (CD)
7-685-790-09 SCREW +PTT 2.6X4 (S)
#2
7-685-792-09 SCREW +PTT 2.6X6 (S)
8
39
CDX-M800
5-2. CAM SECTION
59
58
55
57
#5
56
#2 #2
61
60
M601
#4
#2
#5
#2
58
64 #2
#2
54
65
63
#5
62
53
#7
51
#5
#5
#5
52
Ref. No.
Part No.
Description
51
52
53
54
55
3-230-495-01
X-3380-549-1
X-3380-544-2
X-3380-548-1
X-3382-822-1
CAM (L)
ARM (B-R) ASSY
BRACKET (L) ASSY
ARM (B-L) ASSY
ARM (A-L) ASSY
56
57
58
59
60
3-376-464-11
3-045-714-01
3-342-940-01
3-045-713-01
A-3326-298-A
SCREW (+PTT 2.6X6), GROUND POINT
GEAR (B)
WASHER (M)
GEAR (A)
SWITCH BOARD, COMPLETE
* 61
40
X-3378-711-4 BRACKET (MOTOR) ASSY
Remark
Ref. No.
66
Part No.
Description
62
63
64
65
66
3-230-494-01
3-230-496-01
X-3380-545-2
3-030-909-11
X-3382-823-1
GEAR (C)
CAM (R)
BRACKET (R) ASSY
DAMPER, OIL
ARM (A-R) ASSY
M601
#2
#4
#5
#7
X-3378-769-1
7-685-792-09
7-627-553-28
7-624-102-04
7-621-772-18
MOTOR ASSY (OPEN/CLOSE)
SCREW +PTT 2.6X6 (S)
SCREW, PRECISION +P 2X2.5
STOP RING 1.5, TYPE -E
SCREW +P 2X4
Remark
CDX-M800
5-3. MAIN BOARD SECTION
107
#2
#2
106
105
#2
not
supplied
108
#3
#2
#2
#2
#2
not supplied
#2
#2
102
TUX501
103
104
105
103
F901
102
101
101
not supplied
not supplied
Ref. No.
Part No.
Description
101
102
103
104
105
3-230-493-01
3-230-444-01
3-040-692-01
3-045-721-01
3-376-464-11
GEAR (DRIVE SHAFT)
GUIDE (DRIVE SHAFT)
RING, CE TYPE RETAINING
SHAFT, DRIVE
SCREW (+PTT 2.6X6), GROUND POINT
106
106
A-3274-749-A MAIN BOARD, COMPLETE (US,CND)
A-3274-769-A MAIN BOARD, COMPLETE (AEP,UK,E)
Remark
Ref. No.
Part No.
Description
Remark
107
108
F901
TUX501
#2
1-777-246-41
1-790-375-22
1-532-877-11
A-3220-887-A
7-685-792-09
CORD (WITH CONNECTOR) (ANTENNA)
CORD (WITH CONNECTOR) (SUB OUT (MONO))
FUSE (BLADE TYPE) (AUTO FUSE) 10A
TUNER UNIT (TUX-030)
SCREW +PTT 2.6X6 (S)
#3
7-685-795-09 SCREW +PTT 2.6X12 (S)
41
CDX-M800
5-4. FRONT PANEL SECTION
166
164
174
not supplied
FL900
165
163
164
#6
167
#6
171
172
162
LCD2
160
154
161
170
159
168
173
157
not supplied
158
156
169
154
155
151
153
152
Ref. No.
Part No.
Description
Part No.
Description
151
151
152
153
153
X-3382-818-1
X-3382-824-1
3-238-816-01
3-238-820-01
3-238-820-11
PANEL (KEY) ASSY, FRONT (US,CND)
PANEL (KEY) ASSY, FRONT (AEP,UK,E)
BUTTON (EJECT)
BUTTON (ENTER) (US,CND)
BUTTON (ENTER) (AEP,UK,E)
164
165
166
167
168
3-248-791-01
3-248-789-01
2-626-869-01
1-687-952-11
X-3381-646-1
BUTTON (OPEN)
BUTTON (RESET-DSPL)
SCREW (M2X3), SERRATION (US,CND)
FLEXIBLE BOARD
BRACKET (PANEL) ASSY
154
155
156
157
158
3-238-814-01
X-3381-650-1
3-238-821-01
3-238-819-01
3-238-817-01
HOLDER (REFLECTION), BUTTON
BUTTON (SEEK/AMS) ASSY
BUTTON (DISC)
BUTTON (SOUND)
BUTTON (DSO)
169
169
170
171
172
A-3274-753-A
A-3274-766-A
3-238-827-01
3-238-826-01
1-694-925-11
DISPLAY BOARD, COMPLETE (US,CND)
DISPLAY BOARD, COMPLETE (AEP,UK,E)
PLATE (LCD KEY), LIGHT GUIDE
SHEET (KEY), DIFFUSION
CONDUCTIVE BOARD, CONNECTION
159
159
160
161
162
3-238-818-01
3-238-818-11
X-3381-649-1
3-238-815-01
3-239-338-01
BUTTON (MODE) (US,CND)
BUTTON (MODE) (AEP,UK,E)
BUTTON (VOL) ASSY
BUTTON (CLOSE)
BUTTON (SOURCE)
173
174
FL900
LCD2
#6
1-694-926-11
X-3383-210-1
1-518-879-11
1-804-636-21
7-685-104-19
CONDUCTIVE BOARD, CONNECTION
PANEL (MAIN) ASSY, FRONT
INDICATOR TUBE, FLUORESCENT
DISPLAY PANEL, LIQUID CRYSTAL
SCREW +P 2X6 TYPE2 NON-SLIT
163
3-248-825-01 PLATE (FL), GUIDE
42
Remark
Ref. No.
Remark
CDX-M800
5-5. CD MECHANISM SECTION (1)
(MG-393XC-121//K)
202
#8
#8
204
203
207
209
201
#9
216
218
214
215
206
211
205
214
217
205
C
213
210
C
#10
M903
212
#9
#9
208
Ref. No.
Remark
Ref. No.
#8
Part No.
Description
Part No.
Description
201
202
203
204
205
1-683-283-11
3-040-039-03
3-040-038-01
3-040-050-01
3-040-022-01
IN SELF SW BOARD
CHASSIS (T)
SPRING (LR), TENSION
LEVER (L)
RETAINER (ROLLER), SHAFT
212
213
214
215
216
3-221-779-02
3-040-034-01
3-040-042-01
3-043-880-01
3-044-206-11
BRACKET (MOTOR)
SPRING (RA), TENSION
WASHER
RING (RA), RETAINING
SCREW, SPECIAL
206
207
208
209
210
3-040-044-01
3-040-067-01
A-3301-980-A
3-040-037-01
3-040-040-03
ROLLER (S)
LEVER (R)
SHAFT ROLLER ASSY
GUIDE (DISC)
ARM (ROLLER)
217
218
M903
#8
#9
1-683-284-11
1-685-337-11
A-3315-039-A
7-627-553-37
7-628-253-00
FLEXIBLE BOARD
LOAD SW BOARD
MOTOR SUB ASSY, LO (LOADING)
SCREW, PRECISION +P 2X3 TYPE3
SCREW, SPECIAL
211
A-3283-233-A SERVO BOARD, COMPLETE
#10
7-627-553-17 SCREW, PRECISION +P 2X2 TYPE3
Remark
43
CDX-M800
5-6. CD MECHANISM SECTION (2)
(MG-393XC-121//K)
254
251
256
257
257
258
D
260
264
not supplied
262
253
255
263
261
D
259
252
252
252
Ref. No.
Part No.
Description
251
252
253
254
255
3-040-025-02
3-040-031-01
3-040-056-01
3-040-024-01
3-040-054-01
ARM, CHUCKING
DAMPER (T)
LEVER (D)
RETAINER (DISC)
WHEEL (LW), WORM
256
257
3-040-026-01 SPRING (CH), TENSION
3-040-032-01 SPRING (FL), COMPRESSION
44
Remark
Ref. No.
Part No.
Description
258
259
260
261
262
3-040-033-01
A-3307-422-A
3-040-059-01
3-040-057-01
3-040-058-01
SPRING (KF1), TENSION
CHASSIS (M) COMPLETE ASSY
SPRING (TR), TENSION
LEVER (LOCK)
GEAR (MDL)
263
264
3-040-052-01 WHEEL (U), WORM
3-040-051-02 LEVER (TR)
Remark
CDX-M800
5-7. CD MECHANISM SECTION (3)
(MG-393XC-121//K)
301
M901
307
302
M902
303
308
#11
309
310
#8
304
305
306
309
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Ref. No.
Part No.
Description
301
302
303
304
305
X-3378-480-1
3-040-029-01
3-040-045-01
3-040-194-01
A-3301-983-A
CHASSIS (OP) ASSY (including M901)
SPRING (SL), TORSION
BASE (DRIVING)
GEAR (MIDWAY)
SHAFT (FEED) ASSY
306
307
3-040-030-01 SPRING (FEED), PLATE
1-823-641-11 CABLE, FLEXIBLE FLAT (6 CORE)
Remark
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
Ref. No.
Part No.
Description
308
309
0 310
M902
#8
1-683-282-11
3-909-607-01
8-820-165-06
A-3301-985-A
7-627-553-37
SL SW BOARD
SCREW
OPTICAL PICK-UP KSS-721A/C-RP
MOTOR ASSY, SLED (SLED)
SCREW, PRECISION +P 2X3 TYPE3
#11
Remark
7-627-850-28 SCREW, PRECISION +P 1.4X3
45
CDX-M800
SECTION 6
ELECTRICAL PARTS LIST
DISPLAY
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
• Abbreviation
CND: Canadian model
Ref. No.
Part No.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORS
uF : µF
• COILS
uH : µH
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
When indicating parts by reference
number, please include the board.
Description
Remark
A-3274-753-A DISPLAY BOARD, COMPLETE (US,CND)
A-3274-766-A DISPLAY BOARD, COMPLETE (AEP,UK,E)
************************
1-694-925-11
1-694-926-11
3-238-826-01
3-238-827-01
3-248-825-01
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
CONDUCTIVE BOARD, CONNECTION
CONDUCTIVE BOARD, CONNECTION
SHEET (KEY), DIFFUSION
PLATE (LCD KEY), LIGHT GUIDE
PLATE (FL), GUIDE
< CAPACITOR >
Ref. No.
Part No.
Description
Remark
FB902
FB903
FB904
FB905
FB906
1-216-864-11
1-216-864-11
1-216-864-11
1-500-329-21
1-500-329-21
METAL CHIP
0
METAL CHIP
0
METAL CHIP
0
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
5%
5%
5%
1/10W
1/10W
1/10W
FB907
FB908
FB909
FB911
FB912
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-500-329-21
METAL CHIP
0
METAL CHIP
0
METAL CHIP
0
METAL CHIP
0
INDUCTOR, FERRITE BEAD
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
C901
C902
C903
C904
C905
1-125-837-11
1-125-837-11
1-162-959-11
1-127-760-11
1-124-778-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
1uF
1uF
330PF
4.7uF
22uF
10%
10%
5%
10%
20%
6.3V
6.3V
50V
6.3V
6.3V
FB913
FB914
FB915
FB916
FB917
1-500-329-21
1-500-329-21
1-500-329-21
1-500-329-21
1-500-329-21
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
C907
C908
C909
C910
C911
1-164-004-11
1-165-176-11
1-165-176-11
1-165-176-11
1-115-412-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.047uF
0.047uF
0.047uF
680PF
10%
10%
10%
10%
5%
25V
16V
16V
16V
25V
FB920
FB921
FB922
FB923
FB925
1-500-329-21
1-500-329-21
1-500-329-21
1-500-329-21
1-500-329-21
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
C912
C913
C914
C960
C961
1-164-004-11
1-164-004-11
1-162-970-11
1-162-908-11
1-162-907-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.01uF
3PF
2PF
10%
10%
10%
0.25PF
0.25PF
25V
25V
25V
50V
50V
FB926
FB971
1-500-329-21 INDUCTOR, FERRITE BEAD
1-500-329-21 INDUCTOR, FERRITE BEAD
C962
C963
C964
C970
C973
1-164-156-11
1-165-319-11
1-126-601-11
1-164-156-11
1-165-319-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
2.2uF
0.1uF
0.1uF
20%
25V
50V
50V
25V
50V
C983
1-125-837-11 CERAMIC CHIP
1uF
10%
< FLUORESCENT INDICATOR >
FL900
6.3V
1-518-879-11 INDICATOR TUBE, FLUORESCENT
< JUMPER RESISTOR >
FL910
FL918
FL919
FL924
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
< CONNECTOR >
IC1
IC2
IC62
IC301
< DIODE >
8-719-083-14
8-719-978-33
8-719-069-54
8-719-056-85
DIODE
DIODE
DIODE
DIODE
RRX9000-0501
DTZ-TT11-6.8B
UDZS-TE-17-5.1B
UDZ-TE-17-8.2B
46
1-500-329-21 INDUCTOR, FERRITE BEAD
1-216-864-11 METAL CHIP
0
5%
5%
5%
5%
6-701-630-01
6-802-887-01
8-759-830-18
8-759-523-94
IC
IC
IC
IC
LC75848T-E
M30833FJGP-066
RRX9000-0601#1
TC74VHC32FT(EL)
< LIQUID CRYSTAL DISPLAY >
LCD2
< FERRITE BEAD >
FB60
FB901
0
0
0
0
< IC >
CNP908 1-774-678-21 CONNECTOR, FPC (ZIF) 24P
D70
D901
D902
D908
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1-804-636-21 DISPLAY PANEL, LIQUID CRYSTAL
< DIODE >
5%
1/10W
LED901 8-719-053-09 LED SML-310VT-T86 (OFF)
LED902 8-719-053-09 LED SML-310VT-T86 (SOURCE)
1/10W
1/10W
1/10W
1/10W
CDX-M800
DISPLAY
Ref. No.
Part No.
Description
Part No.
Description
LED903
LED905
LED906
LED908
LED909
8-719-053-09
8-719-053-09
8-719-053-09
8-719-053-09
8-719-080-04
LED
LED
LED
LED
LED
SML-310VT-T86 (CLOSE)
SML-310VT-T86 (SCRL)
SML-310VT-T86 (DSPL)
SML-310VT-T86 (MODE)
CL-190UB-X-T (IMAGE)
Remark
R944
R945
R946
R947
R950
1-216-845-11
1-216-048-11
1-216-035-11
1-216-845-11
1-216-033-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
910
270
100K
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
LED911
LED912
LED913
LED915
LED916
8-719-053-09
8-719-053-09
8-719-053-09
8-719-053-09
8-719-053-09
LED
LED
LED
LED
LED
SML-310VT-T86 (Z)
SML-310VT-T86 (DISC –)
SML-310VT-T86 (ENTER)
SML-310VT-T86 (LIST)
SML-310VT-T86 (DISC +)
R951
R952
R953
R954
R955
1-216-040-11
1-216-035-11
1-216-040-11
1-216-048-11
1-216-040-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
430
270
430
910
430
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
LED917
LED919
LED920
LED921
LED922
8-719-053-09
8-719-053-09
8-719-053-09
8-719-053-09
8-719-053-09
LED
LED
LED
LED
LED
SML-310VT-T86 (MENU)
SML-310VT-T86 (DSO)
SML-310VT-T86 (EQ7)
SML-310VT-T86 (SOUND)
SML-310VT-T86 (TA) (AEP,UK,E)
R956
R957
R958
R959
R960
1-216-040-11
1-216-040-11
1-216-040-11
1-216-040-11
1-216-040-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
430
430
430
430
430
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
LED931
LED955
LED956
LED957
LED958
8-719-080-04
8-719-076-58
8-719-076-58
8-719-079-10
8-719-079-10
LED
LED
LED
LED
LED
CL-190UB-X-T (OPEN)
NSSW440-BRS (LCD BACK LIGHT)
NSSW440-BRS (LCD BACK LIGHT)
CL-220UB-X-TS (VOL)
CL-220UB-X-TS (SEEK/AMS)
R961
R962
R964
R967
R968
1-216-040-11
1-216-040-11
1-218-288-11
1-216-805-11
1-216-850-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
430
430
300
47
270K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R969
R970
R971
R978
R979
1-216-846-11
1-216-818-11
1-216-009-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
120K
560
22
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R980
R981
R982
R984
R985
1-216-809-11
1-216-821-11
1-216-841-11
1-216-825-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
1K
47K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R986
R987
R988
R990
1-216-825-11
1-216-825-11
1-216-035-11
1-216-025-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
2.2K
2.2K
270
100
5%
5%
5%
5%
R991
1-218-855-11 RES-CHIP
2.2K
2%
1/10W
1/10W
1/10W
1/10W
(US,CND)
1/16W
R992
R994
1-218-855-11 RES-CHIP
1-216-864-11 METAL CHIP
2.2K
0
2%
5%
1/16W
1/10W
< TRANSISTOR >
Q903
Q904
Q905
Q907
Q908
8-729-106-60
8-729-900-53
8-729-904-66
8-729-216-22
8-729-900-53
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SB1115A
DTC114EK
DTD113EK-T-146
2SA1162-G
DTC114EK
< RESISTOR >
R901
R902
R906
R907
R908
1-216-833-11
1-216-829-11
1-218-855-11
1-218-855-11
1-218-851-11
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
4.7K
2.2K
2.2K
1.5K
5%
5%
2%
2%
2%
1/10W
1/10W
1/16W
1/16W
1/16W
R909
R910
R911
R912
R913
1-218-851-11
1-218-847-11
1-219-286-11
1-219-286-11
1-219-286-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1.5K
1K
680
680
680
2%
2%
2%
2%
2%
1/16W
1/16W
1/16W
1/16W
1/16W
R914
R915
R916
R917
R918
1-218-867-11
1-218-863-11
1-218-859-11
1-218-855-11
1-218-851-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
6.8K
4.7K
3.3K
2.2K
1.5K
2%
2%
2%
2%
2%
1/16W
1/16W
1/16W
1/16W
1/16W
R919
R920
R921
R922
R923
1-218-851-11
1-218-847-11
1-219-286-11
1-219-286-11
1-219-286-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1.5K
1K
680
680
680
2%
2%
2%
2%
2%
1/16W
1/16W
1/16W
1/16W
1/16W
R925
1-218-871-11 RES-CHIP
10K
2%
R928
R929
R935
R936
1-216-829-11
1-216-833-11
1-216-033-00
1-216-033-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
4.7K
10K
220
220
5%
5%
5%
5%
1/16W
(AEP,UK,E)
1/10W
1/10W
1/10W
1/10W
R939
R940
R941
R942
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
100K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
Ref. No.
Remark
< SWITCH >
S901
S902
S903
S904
S905
1-771-884-31
1-771-884-31
1-771-884-31
1-771-884-31
1-771-884-31
SWITCH, TACTILE (WITH LED) (OFF)
SWITCH, TACTILE (WITH LED) (SOURCE)
SWITCH, TACTILE (WITH LED) (CLOSE)
SWITCH, TACTILE (WITH LED) (VOL –)
SWITCH, TACTILE (WITH LED) (SCRL)
S906
S907
S908
S909
S911
1-771-884-31
1-771-884-31
1-771-884-31
1-771-884-31
1-771-884-31
SWITCH, TACTILE (WITH LED) (DSPL)
SWITCH, TACTILE (WITH LED) (VOL +)
SWITCH, TACTILE (WITH LED) (MODE)
SWITCH, TACTILE (WITH LED) (IMAGE)
SWITCH, TACTILE (WITH LED) (Z)
S912
S913
S914
S915
S916
1-771-884-31 SWITCH, TACTILE (WITH LED) (DISC –)
1-771-884-31 SWITCH, TACTILE (WITH LED) (ENTER)
1-771-884-31 SWITCH, TACTILE (WITH LED)
(SEEK/AMS > M)
1-771-884-31 SWITCH, TACTILE (WITH LED) (LIST)
1-771-884-31 SWITCH, TACTILE (WITH LED) (DISC +)
S917
1-771-884-31 SWITCH, TACTILE (WITH LED) (MENU)
47
CDX-M800
DISPLAY
Ref. No.
S918
IN SELF SW
Part No.
LOAD SW
Description
Remark
S919
S920
S921
S922
1-771-884-31 SWITCH, TACTILE (WITH LED)
(SEEK/AMS . m)
1-771-884-31 SWITCH, TACTILE (WITH LED) (DSO)
1-771-884-31 SWITCH, TACTILE (WITH LED) (EQ7)
1-771-884-31 SWITCH, TACTILE (WITH LED) (SOUND)
1-771-884-21 SWITCH, TACTILE (WITH LED) (TA) (AEP,UK,E)
S931
S932
1-771-884-31 SWITCH, TACTILE (WITH LED) (OPEN)
1-771-884-31 SWITCH, TACTILE (WITH LED) (RESET)
< VIBRATOR >
X301
1-795-818-21 VIBRATOR, CRYSTAL (30MHz)
*************************************************************
1-683-283-11 IN SELF SW BOARD
****************
*************************************************************
1-685-337-11 LOAD SW BOARD
***************
*************************************************************
A-3274-749-A MAIN BOARD, COMPLETE (US,CND)
A-3274-769-A MAIN BOARD, COMPLETE (AEP,UK,E)
*********************
7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT
7-685-792-09 SCREW +PTT 2.6X6 (S)
7-685-795-09 SCREW +PTT 2.6X12 (S)
< CAPACITOR >
C101
C102
C103
C104
C105
1-126-940-11
1-104-942-11
1-135-473-21
1-162-964-11
1-162-964-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
330uF
1uF
3300uF
0.001uF
0.001uF
20%
20%
20%
10%
10%
16V
50V
16V
50V
50V
C142
C173
C178
C183
C188
1-162-927-11
1-128-428-11
1-162-927-11
1-128-428-11
1-162-927-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
100PF
10uF
100PF
10uF
100PF
5%
20%
5%
20%
5%
50V
35V
50V
35V
50V
C199
C201
C202
C203
C204
1-162-927-11
1-115-467-11
1-162-923-11
1-124-257-00
1-124-234-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
100PF
0.22uF
47PF
2.2uF
22uF
5%
10%
5%
20%
20%
50V
10V
50V
50V
16V
C206
C207
C212
C214
C215
1-125-891-11
1-125-891-11
1-104-396-11
1-104-396-11
1-125-891-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
0.47uF
0.47uF
10uF
10uF
0.47uF
10%
10%
20%
20%
10%
10V
10V
16V
16V
10V
C218
C219
C221
C223
C226
1-125-891-11
1-125-891-11
1-104-396-11
1-104-396-11
1-104-396-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
0.47uF
0.47uF
10uF
10uF
10uF
10%
10%
20%
20%
20%
10V
10V
16V
16V
16V
C242
C273
C278
C283
C288
1-162-927-11
1-128-428-11
1-162-927-11
1-128-428-11
1-162-927-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
100PF
10uF
100PF
10uF
100PF
5%
20%
5%
20%
5%
50V
35V
50V
35V
50V
48
MAIN
Ref. No.
Part No.
Description
C301
C302
C303
C304
C305
1-128-057-11
1-162-964-11
1-124-584-00
1-162-964-11
1-124-234-00
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
330uF
0.001uF
100uF
0.001uF
22uF
20%
10%
20%
10%
20%
6.3V
50V
10V
50V
16V
Remark
C306
C307
C308
C309
C310
1-124-234-00
1-162-927-11
1-104-942-11
1-104-942-11
1-162-970-11
ELECT
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
22uF
100PF
1uF
1uF
0.01uF
20%
5%
20%
20%
10%
16V
50V
50V
50V
25V
C311
C312
C313
C315
C316
1-128-647-11
1-124-584-00
1-164-156-11
1-162-918-11
1-162-918-11
DOUBLE LAYERS
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1F
100uF
0.1uF
18PF
18PF
C317
C318
C319
C320
C321
1-162-970-11
1-162-968-11
1-125-837-11
1-125-837-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.0047uF
1uF
1uF
0.1uF
10%
10%
10%
10%
25V
50V
6.3V
6.3V
25V
C322
C323
C334
C335
C336
1-164-160-11
1-162-917-11
1-164-156-11
1-164-156-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
20PF
15PF
0.1uF
0.1uF
0.001uF
5%
5%
50V
50V
25V
25V
50V
C337
C338
C339
C341
C342
1-164-156-11
1-164-156-11
1-164-156-11
1-124-589-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
47uF
0.1uF
C401
C402
C416
C417
C418
1-124-589-11
1-125-889-11
1-125-837-11
1-125-837-11
1-104-396-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
47uF
2.2uF
1uF
1uF
10uF
20%
10%
10%
10%
20%
16V
10V
6.3V
6.3V
16V
C419
C420
C421
C422
C423
1-125-891-11
1-125-891-11
1-125-837-11
1-124-584-00
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.47uF
0.47uF
1uF
100uF
0.01uF
10%
10%
10%
20%
10%
10V
10V
6.3V
10V
25V
C424
C425
C426
C427
C428
1-162-965-11
1-136-154-00
1-162-927-11
1-162-927-11
1-162-927-11
CERAMIC CHIP
FILM
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0015uF
0.012uF
100PF
100PF
100PF
10%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C429
C430
C431
C432
C433
1-162-927-11
1-162-965-11
1-162-927-11
1-136-154-00
1-104-942-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
FILM
ELECT
100PF
0.0015uF
100PF
0.012uF
1uF
5%
10%
5%
5%
20%
50V
50V
50V
50V
50V
C434
C435
C442
C443
C501
1-104-942-11
1-104-942-11
1-162-927-11
1-128-428-11
1-162-970-11
ELECT
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
1uF
1uF
100PF
10uF
0.01uF
20%
20%
5%
20%
10%
50V
50V
50V
35V
25V
C502
C503
1-104-396-11 ELECT
1-124-259-11 ELECT
10uF
4.7uF
20%
20%
20%
5%
5%
10%
20%
5.5V
10V
25V
50V
50V
25V
25V
25V
16V
25V
16V
16V
(AEP,UK,E)
CDX-M800
MAIN
Ref. No.
Part No.
Description
Remark
C505
1-162-964-11 CERAMIC CHIP
0.001uF
10%
50V
(AEP,UK,E)
10%
50V
(AEP,UK,E)
10%
50V
(AEP,UK,E)
25V
(AEP,UK,E)
5%
50V
(AEP,UK,E)
C506
1-162-964-11 CERAMIC CHIP
0.001uF
C520
1-162-964-11 CERAMIC CHIP
0.001uF
C521
1-164-156-11 CERAMIC CHIP
0.1uF
C522
1-162-920-11 CERAMIC CHIP
27PF
C523
1-162-920-11 CERAMIC CHIP
27PF
C524
1-126-786-11 ELECT
47uF
C525
1-164-156-11 CERAMIC CHIP
0.1uF
C526
1-162-959-11 CERAMIC CHIP
330PF
C527
1-135-834-11 CERAMIC CHIP
2.2uF
C528
1-164-739-11 CERAMIC CHIP
560PF
C802
C803
C807
C809
1-165-874-21
1-128-576-11
1-110-501-11
1-164-156-11
ELECT CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
120uF
100uF
0.33uF
0.1uF
C810
C823
C928
C901
C903
1-104-607-21
1-126-924-11
1-164-156-11
1-124-234-00
1-164-156-11
ELECT CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
47uF
330uF
0.1uF
22uF
0.1uF
20%
20%
C930
1-124-234-00 ELECT
22uF
20%
50V
(AEP,UK,E)
20%
16V
(AEP,UK,E)
25V
(AEP,UK,E)
5%
50V
(AEP,UK,E)
6.3V
(AEP,UK,E)
Ref. No.
Part No.
Description
D113
D114
D115
D116
D117
6-500-508-01
6-500-508-01
6-500-508-01
6-500-508-01
6-500-508-01
DIODE
DIODE
DIODE
DIODE
DIODE
RR263M-400FTR
RR263M-400FTR
RR263M-400FTR
RR263M-400FTR
RR263M-400FTR
D118
D119
D120
D121
D122
8-719-053-18
8-719-053-18
8-719-053-18
8-719-053-18
8-719-978-33
DIODE
DIODE
DIODE
DIODE
DIODE
1SR154-400TE-25
1SR154-400TE-25
1SR154-400TE-25
1SR154-400TE-25
DTZ-TT11-6.8B
D302
D303
D305
D401
D501
8-719-914-43
8-719-914-44
8-719-988-61
8-719-404-50
8-719-069-55
DIODE
DIODE
DIODE
DIODE
DIODE
DAN202K
DAP202K
1SS355TE-17
MA111-TX
UDZS-TE-17-5.6B
D802
D803
D804
D805
D806
8-719-053-18
8-719-053-18
8-719-055-30
8-719-055-30
8-719-055-33
DIODE
DIODE
DIODE
DIODE
DIODE
1SR154-400TE-25
1SR154-400TE-25
D1FS4A-TA
D1FS4A-TA
D1FL40
D808
D810
D819
D820
D825
8-719-978-33
8-719-978-33
8-719-978-33
8-719-978-33
8-719-978-33
DIODE
DIODE
DIODE
DIODE
DIODE
DTZ-TT11-6.8B
DTZ-TT11-6.8B
DTZ-TT11-6.8B
DTZ-TT11-6.8B
DTZ-TT11-6.8B
D826
D827
D828
D829
D831
8-719-978-33
8-719-978-33
8-719-978-33
8-719-978-33
8-719-978-33
DIODE
DIODE
DIODE
DIODE
DIODE
DTZ-TT11-6.8B
DTZ-TT11-6.8B
DTZ-TT11-6.8B
DTZ-TT11-6.8B
DTZ-TT11-6.8B
D832
D843
D904
D905
D907
8-719-988-61
8-719-978-33
8-719-988-61
8-719-069-54
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
1SS355TE-17
DTZ-TT11-6.8B
1SS355TE-17
UDZS-TE-17-5.1B
1SS355TE-17
D909
8-719-988-61 DIODE 1SS355TE-17
Remark
5%
5%
50V
(AEP,UK,E)
20%
6.3V
20%
63V
10%
16V
25V
20%
16V
10V
25V
16V
25V
16V
< CONNECTOR >
* CN401
* CN503
* CN601
CNP101
CNP102
1-506-985-11
1-506-984-11
1-506-985-11
1-774-701-21
1-580-907-31
PIN, CONNECTOR (PC BOARD) 3P
PIN, CONNECTOR (PC BOARD) 2P
PIN, CONNECTOR (PC BOARD) 3P
PIN, CONNECTOR 16P
PLUG, CONNECTOR (BUS CONTROL IN)
CNP301
CNP805
* CNP902
CNP909
1-815-260-11
1-563-614-31
1-568-954-11
1-774-677-21
CONNECTOR, BOARD TO BOARD 30P
CONNECTOR, FLEXIBLE 11P
PIN, CONNECTOR 5P
CONNECTOR, FPC (ZIF) 24P
< FERRITE BEAD >
< JACK >
CNJ101 1-764-270-11 JACK, STEREO MINIATURE (DIA.3.5)
(REMOTE IN) (AEP,UK,E)
FB101
FB102
FB301
FB302
FB303
1-414-813-11
1-414-813-11
1-216-295-11
1-216-295-11
1-414-813-11
FERRITE, EMI (SMD) (AEP,UK,E)
FERRITE, EMI (SMD) (AEP,UK,E)
SHORT CHIP
0
SHORT CHIP
0
FERRITE, EMI (SMD)
FB501
1-414-813-11 FERRITE, EMI (SMD) (AEP,UK,E)
< IC >
< DIODE >
D101
D102
D103
D104
D105
8-719-083-66
8-719-083-66
8-719-420-51
8-719-069-56
8-719-083-66
DIODE
DIODE
DIODE
DIODE
DIODE
UDZS-TE-17-18B
UDZS-TE-17-18B
MA729
UDZS-TE-17-6.2B
UDZS-TE-17-18B
D106
D109
D110
D111
D112
8-719-978-33
8-719-049-38
6-500-508-01
6-500-508-01
6-500-508-01
DIODE
DIODE
DIODE
DIODE
DIODE
DTZ-TT11-6.8B
1N5404TU
RR263M-400FTR
RR263M-400FTR
RR263M-400FTR
IC201
IC301
IC302
IC303
IC303
6-703-375-01
8-759-449-89
8-759-658-25
6-802-884-01
6-802-885-01
IC
IC
IC
IC
IC
TDA8588J/N1
BA8270F-E2
PST3432UL
M30626FHPGP-052 (US,CND)
M30626FHPGP-053 (AEP,UK,E)
IC306
IC307
IC308
IC401
IC502
8-759-668-14
8-759-580-33
8-759-701-01
6-703-303-01
6-703-809-01
IC
IC
IC
IC
IC
PQ09DZ1U
BA6288FS-E2
NJM2904M
TDA7416
SAA6588T/V2-518 (AEP,UK,E)
IC800
8-759-598-63 IC LM2577SX-ADJ
49
CDX-M800
MAIN
Ref. No.
Part No.
Description
Remark
< JUMPER RESISTOR >
JR300
JR301
1-216-864-11 METAL CHIP
1-216-864-11 METAL CHIP
0
0
5%
5%
JR302
1-216-864-11 METAL CHIP
0
5%
1/10W
1/10W
(AEP,UK,E)
1/10W
(US,CND)
< COIL >
L101
L302
L303
L800
1-419-476-31
1-414-185-51
1-412-006-31
1-424-911-11
COIL, CHOKE
INDUCTOR
INDUCTOR
COIL, POWER
250uH
22uH (US,CND)
10uH
100uH
< JACK >
PJ401
1-774-700-11 JACK, PIN 6P (BUS AUDIO IN/AUX-IN,
AUDIO OUT REAR/FRONT)
< TRANSISTOR >
Q101
Q102
Q103
Q171
Q181
8-729-900-53
8-729-901-81
8-729-901-81
8-729-920-21
8-729-920-21
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114EK
2SC2412K-T-146-R
2SC2412K-T-146-R
DTC314TK-T-146
DTC314TK-T-146
Q271
Q281
Q301
Q305
Q306
8-729-920-21
8-729-920-21
8-729-901-81
8-729-901-00
8-729-216-22
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC314TK-T-146
DTC314TK-T-146
2SC2412K-T-146-R
DTC124EK
2SA1162-G
Q307
Q401
Q402
Q408
Q470
8-729-901-81
8-729-900-53
8-729-027-23
8-729-053-84
8-729-920-21
TRANSISTOR 2SC2412K-T-146-R
TRANSISTOR DTC114EK
TRANSISTOR DTA114EKA-T146
FET SSM3KO9FU(T5LSONY1)
TRANSISTOR DTC314TK-T-146
Q501
Q801
Q802
Q907
Q914
8-729-106-68
8-729-054-36
1-801-806-11
8-729-901-81
8-729-027-31
TRANSISTOR 2SD1615A-GP
FET UPA1716G-E2
TRANSISTOR DTC144EKA
TRANSISTOR 2SC2412K-T-146-R
TRANSISTOR DTA124EKA-T146
Q915
Q916
8-729-015-11 TRANSISTOR 2SD1802FAST-TL
8-729-901-00 TRANSISTOR DTC124EK
< RESISTOR >
R101
R102
R103
R104
R105
1-216-835-11
1-216-821-11
1-216-821-11
1-216-829-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
15K
1K
1K
4.7K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R106
R107
R108
R109
R110
1-216-841-11
1-216-073-00
1-216-073-00
1-216-833-11
1-216-833-11
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
47K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R111
R112
R142
R143
R172
1-216-841-11
1-216-821-11
1-216-825-11
1-216-833-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
1K
2.2K
10K
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
50
Ref. No.
Part No.
Description
R174
R175
R182
R184
R185
1-216-809-11
1-216-841-11
1-216-864-11
1-216-809-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
47K
0
100
47K
5%
5%
5%
5%
5%
Remark
1/10W
1/10W
1/10W
1/10W
1/10W
R201
R202
R203
R204
R205
1-216-841-11
1-216-809-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
100
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R206
R242
R243
R272
R274
1-216-821-11
1-216-825-11
1-216-833-11
1-216-864-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
2.2K
10K
0
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R275
R282
R284
R285
R301
1-216-841-11
1-216-864-11
1-216-809-11
1-216-841-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
0
100
47K
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R302
R303
R304
R305
R306
1-216-864-11
1-216-864-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R307
R308
R309
R310
R311
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R312
R313
R316
R317
R318
1-216-845-11
1-216-845-11
1-216-845-11
1-216-809-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
100
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R319
R320
R322
R323
R324
1-216-821-11
1-216-809-11
1-216-823-11
1-216-823-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
100
1.5K
1.5K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R325
R326
R327
R328
R332
1-216-845-11
1-216-853-11
1-216-845-11
1-216-845-11
1-218-871-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
470K
100K
100K
10K
5%
5%
5%
5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
(AEP,UK,E)
R333
1-216-809-11 METAL CHIP
100
5%
R334
R335
R336
R337
1-216-097-11
1-216-837-11
1-216-836-11
1-216-073-00
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
100K
22K
18K
10K
5%
5%
5%
5%
1/10W
(AEP,UK,E)
1/10W
1/10W
1/10W
1/10W
R338
R339
R340
R341
R343
1-216-837-11
1-216-085-11
1-216-298-00
1-216-298-00
1-216-809-11
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
22K
33K
2.2
2.2
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R346
1-216-833-11 METAL CHIP
10K
5%
1/10W
CDX-M800
MAIN
Ref. No.
Part No.
Description
R350
R351
R356
R357
R361
1-216-809-11
1-216-809-11
1-218-871-11
1-218-871-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
R364
Remark
100
100
10K
10K
0
5%
5%
0.5%
0.5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
(AEP,UK,E)
1-216-845-11 METAL CHIP
100K
5%
R365
R366
R367
R368
1-216-845-11
1-216-845-11
1-216-845-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
100
5%
5%
5%
5%
1/10W
(AEP,UK,E)
1/10W
1/10W
1/10W
1/10W
R369
R370
R371
R372
R373
1-216-809-11
1-216-829-11
1-216-298-00
1-216-809-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
4.7K
2.2
100
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R374
R375
R376
R377
R378
1-216-841-11
1-216-841-11
1-216-841-11
1-216-845-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
47K
100K
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R401
R402
R407
R408
R410
1-216-017-11
1-216-809-11
1-216-841-11
1-216-809-11
1-216-295-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
47
100
47K
100
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R414
R415
R416
R417
R418
1-216-833-11
1-216-833-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R419
R420
R421
R422
R424
1-216-809-11
1-216-833-11
1-216-833-11
1-216-813-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
10K
10K
220
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R425
R429
R431
R433
R435
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R439
R440
R441
R442
R443
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R444
R445
R446
R478
R501
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R502
R503
R504
R505
R518
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-797-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
10
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
(AEP,UK,E)
Ref. No.
Part No.
Description
Remark
R519
1-216-817-11 METAL CHIP
470
5%
R520
1-216-832-11 METAL CHIP
8.2K
5%
R521
1-216-797-11 METAL CHIP
10
5%
R800
R801
1-216-230-00 RES-CHIP
1-216-230-00 RES-CHIP
22K
22K
5%
5%
R803
R804
R805
R806
R807
1-218-871-11
1-218-754-11
1-216-296-11
1-216-057-00
1-218-704-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
10K
120K
0
2.2K
3.3K
0.5%
0.5%
1/10W
1/10W
5%
0.5%
1/10W
1/10W
R808
R809
R811
R812
R833
1-216-833-11
1-216-864-11
1-216-845-11
1-216-845-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
0
100K
100K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R845
R866
R901
R902
R903
1-216-821-11
1-216-821-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
0
0
0
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R906
R907
R908
R909
R910
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
0
0
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R911
1-216-809-11 METAL CHIP
100
5%
R911
1-216-864-11 METAL CHIP
0
5%
R912
R915
R920
1-216-864-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-073-00 RES-CHIP
0
100K
10K
5%
5%
5%
1/10W
(AEP,UK,E)
1/10W
(US,CND)
1/10W
1/10W
1/10W
R921
R922
R929
R949
R950
1-216-073-00
1-216-845-11
1-216-837-11
1-216-057-00
1-216-057-00
10K
100K
22K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1/10W
(AEP,UK,E)
1/10W
(AEP,UK,E)
1/10W
(AEP,UK,E)
1/8W
1/8W
< TRANSFORMER >
T800
1-439-812-11 TRANSFORMER, DC-DC CONVERTER
< THERMISTOR (POSITIVE) >
TH100
1-801-792-21 THERMISTOR, POSITIVE
< TUNER >
TUX501 A-3220-887-A TUNER UNIT (TUX-030)
< VIBRATOR >
X301
1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz)
X302
1-767-419-21 VIBRATOR, CRYSTAL (6MHz)
X501
1-579-900-21 VIBRATOR, CRYSTAL (4.3MHz) (AEP,UK,E)
*************************************************************
51
CDX-M800
SERVO
Ref. No.
SL SW
Part No.
SUB
Description
Remark
Ref. No.
Part No.
Description
Remark
< RESISTOR >
A-3283-233-A SERVO BOARD, COMPLETE
**********************
1-683-284-11 FLEXIBLE BOARD
< CAPACITOR >
C1
C3
C4
C5
C6
1-162-970-11
1-162-970-11
1-104-609-11
1-162-970-11
1-125-837-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
100uF
0.01uF
1uF
10%
10%
20%
10%
10%
25V
25V
4V
25V
6.3V
C8
C9
C10
C11
C13
1-107-826-11
1-162-924-11
1-162-924-11
1-162-909-11
1-162-916-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
56PF
56PF
4PF
12PF
10%
5%
5%
0.25PF
5%
16V
50V
50V
50V
50V
C14
C15
C16
C17
C18
1-125-837-11
1-162-970-11
1-162-970-11
1-162-970-11
1-162-966-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.01uF
0.01uF
0.01uF
0.0022uF
10%
10%
10%
10%
10%
6.3V
25V
25V
25V
50V
C19
C20
C21
C22
C23
1-107-826-11
1-107-826-11
1-162-970-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
16V
16V
25V
25V
25V
C24
C25
C26
C27
C29
1-162-970-11
1-162-970-11
1-126-391-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
47uF
0.01uF
0.01uF
10%
10%
20%
10%
10%
25V
25V
6.3V
25V
25V
C30
C34
C35
C36
C37
1-162-970-11
1-162-970-11
1-162-970-11
1-162-970-11
1-126-393-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.01uF
0.01uF
0.01uF
0.01uF
33uF
10%
10%
10%
10%
20%
25V
25V
25V
25V
10V
C38
C40
C41
C43
C44
1-162-970-11
1-107-826-11
1-162-970-11
1-162-967-11
1-125-837-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.01uF
0.0033uF
1uF
10%
10%
10%
10%
10%
25V
16V
25V
50V
6.3V
C45
1-162-970-11 CERAMIC CHIP
0.01uF
10%
25V
R3
R5
R7
R8
R9
1-216-797-11
1-218-344-11
1-216-839-11
1-216-833-11
1-216-840-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10
7.5K
33K
10K
39K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R10
R12
R14
R15
R17
1-216-835-11
1-216-837-11
1-216-841-11
1-216-841-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
15K
22K
47K
47K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R18
R19
R20
R21
R22
1-216-809-11
1-216-809-11
1-216-809-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R26
R29
R30
1-216-797-11 METAL CHIP
1-216-833-11 METAL CHIP
1-216-833-11 METAL CHIP
10
10K
10K
5%
5%
5%
1/10W
1/10W
1/10W
< VIBRATOR >
X1
1-795-520-11 VIBRATOR, CERAMIC (16.9344MHz)
*************************************************************
1-683-282-11 SL SW BOARD
************
*************************************************************
1-687-950-11 SUB BOARD
**********
1-783-268-11 CABLE, FLAT (FFC) 11P (CN501)
< CONNECTOR >
CN1
CN3
1-815-352-11 CONNECTOR, BOARD TO BOARD 30P
1-816-275-21 CONNECTOR, FFC/FPC 6P
< CAPACITOR >
C533
C535
C536
C537
C538
1-125-837-11
1-125-837-11
1-162-970-11
1-125-837-11
1-162-959-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
C539
C540
1-164-156-11 CERAMIC CHIP
1-127-760-11 CERAMIC CHIP
1uF
1uF
0.01uF
1uF
330PF
10%
10%
10%
10%
5%
6.3V
6.3V
25V
6.3V
50V
0.1uF
4.7uF
10%
25V
6.3V
< DIODE >
D506
D507
D511
D512
D513
8-719-069-54
8-719-978-33
8-719-083-66
8-719-079-10
8-719-083-14
DIODE UDZS-TE-17-5.1B
DIODE DTZ-TT11-6.8B
DIODE UDZS-TE-17-18B
LED CL-220UB-X-TS (DISC IN)
DIODE RRX9000-0501
D514
8-719-988-61 DIODE 1SS355TE-17
< JUMPER RESISTOR >
FB1
1-216-864-11 METAL CHIP
0
5%
1/10W
< FERRITE BEAD >
< IC >
FB503
IC1
IC2
8-759-699-98 IC uPD63711GC-8EU
8-759-658-87 IC BA5810FP-E2
< TRANSISTOR >
Q1
52
8-729-904-87 TRANSISTOR 2SB1197K-R
1-500-329-21 INDUCTOR, FERRITE BEAD
< IC >
IC503
8-759-830-18 IC RRX9000-0601#1
CDX-M800
SUB
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
1-216-864-11 METAL CHIP
0
5%
Remark
1/10W
1-476-546-12
1-476-546-22
3-230-549-01
3-251-123-11
REMOTE COMMANDER (RM-X111) (AEP,UK,E)
REMOTE COMMANDER (RM-X110) (US,CND)
LID, BATTERY CASE (for RM-X110/X111)
MANUAL, INSTRUCTION (ENGLISH,FRENCH,
SPANISH) (US,CND)
3-251-123-21 MANUAL, INSTRUCTION (ENGLISH,GERMAN,
FRENCH,ITALIAN,DUTCH) (AEP,UK)
< TRANSISTOR >
Q503
Q504
Description
ACCESSORIES
************
< JUMPER RESISTOR >
JR552
SWITCH
8-729-216-22 TRANSISTOR 2SA1162-G
8-729-900-53 TRANSISTOR DTC114EK
< RESISTOR >
R509
R531
R532
R533
R534
1-216-846-11
1-216-833-11
1-216-845-11
1-216-825-11
1-216-035-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
120K
10K
100K
2.2K
270
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R536
R538
1-216-288-11 METAL CHIP
1-216-850-11 METAL CHIP
300
270K
5%
5%
1/10W
1/10W
3-251-123-31 MANUAL, INSTRUCTION (ENGLISH,
TRADITIONAL CHINESE) (E)
3-251-125-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
FRENCH,SPANISH) (US,CND)
3-251-125-21 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
GERMAN,FRENCH,ITALIAN,DUTCH) (AEP,UK)
3-251-125-31 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
TRADITIONAL CHINESE) (E)
*************************************************************
< SWITCH >
PARTS FOR INSTALLATION AND CONNECTIONS
***************************************
SW501 1-692-135-21 SWITCH, KEYBOARD (RESET)
*************************************************************
A-3326-298-A SWITCH BOARD, COMPLETE (including SW900)
***********************
*************************************************************
MISCELLANEOUS
***************
8
8
107
108
167
301
307
0 310
F901
M601
1-776-207-72 CORD (WITH CONNECTOR) (POWER)
(US,CND,E)
1-776-527-71 CORD (WITH CONNECTOR) (ISO) (POWER)
(AEP,UK)
1-777-246-41 CORD (WITH CONNECTOR) (ANTENNA)
1-790-375-22 CORD (WITH CONNECTOR) (SUB OUT (MONO))
1-687-952-11 FLEXIBLE BOARD
X-3378-480-1
1-823-641-11
8-820-165-06
1-532-877-11
X-3378-769-1
CHASSIS (OP) ASSY (including M901)
CABLE, FLEXIBLE FLAT (6 CORE)
OPTICAL PICK-UP KSS-721A/C-RP
FUSE (BLADE TYPE) (AUTO FUSE) 10A
MOTOR ASSY (OPEN/CLOSE)
351
352
353
354
355
X-3382-647-1
X-3366-405-1
X-3382-821-1
3-934-325-01
1-465-459-21
356
1-776-207-72 CORD (WITH CONNECTOR) (POWER)
(US,CND,E)
1-776-527-71 CORD (WITH CONNECTOR) (ISO) (POWER)
(AEP,UK)
3-246-011-01 KEY (FRAME)
357
358
FRAME ASSY, FITTING
SCREW ASSY (EXP), FITTING (AEP,UK,E)
COLLAR ASSY
SCREW (+K 5X8 TP) (US,CND,E)
ADAPTOR, ANTENNA (AEP,UK)
351
352
353
354
M902
A-3301-985-A MOTOR ASSY, SLED (SLED)
M903
A-3315-039-A MOTOR SUB ASSY, LO (LOADING)
*************************************************************
355
×4
356
357
358
×2
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
53
CDX-M800
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver.
1.0
54
Date
2003. 01
Description of Revision
New
Download PDF

advertising