Data Acquisition Systems - Biopac
Data Acquisition Systems - Biopac
Universal Interface Module
UIM100C
Isolated Power Supply Module
IPS100C
The UIM100C is used to connect 100-series amplifier modules and
signal cables to the system and is included in the MP Starter System.
Sixteen analog input channels plus 2 analog output channels are provided via standard 3.5mm phone jacks on the front panel. The back
panel provides access to 16 digital I/O lines and an external trigger
input via screw terminals. Amplifier modules snap onto the side of
the UIM100C for signal routing to the MP data acquisition unit. The
output of any amplifier module snapped to the UIM100C can be
monitored, during acquisition, via the corresponding 3.5mm analog
channel phone jack. The UIM100C also provides a direct link to the
analog and digital I/O lines of the MP device when collecting or sending data to external equipment. See page 88 for cables to interface
your equipment to the UIM100C.
Not for use with an MP data acquisition module.
The IPS100C is used to operate 100-series amplifier modules independent of an MP data acquisition unit. The IPS100C module couples
the 100-series amplifier outputs directly to any other data acquisition
system, oscilloscope or chart recorder. Amplifier modules snap onto
the side of the IPS100C to receive the necessary isolated power and
to direct the modules’ output to the front panel of the IPS100C. The
IPS100C allows you to operate up to 16 amplifiers on a stand-alone
basis. The analog channel outputs are provided via 3.5mm phone
jacks on the front panel. The IPS100C is generally used with animal
or tissue preparations. When collecting data from electrodes
attached to humans, use the HLT100C module with INISO and OUTISO signal isolators to couple signals to mains powered external laboratory equipment.
Previous
Next
Table of
Contents
Product
Index
Search
Home
Contact
Us
Previous
IMPORTANT USAGE NOTE
Mains powered external laboratory equipment should be connected
to an MP System through Signal Isolators when the system also connects to electrodes attached to humans. For analog signals, use the
INISO or OUTISO isolator (with the HLT100C) to couple external
equipment to an MP System. For digital signals, use the STP100 (with
the UIM100C) to couple external equipment to an MP System.
Contact BIOPAC for details.
Do not use the IPS100C with an MP based system. For a fully isolated recording system using the IPS100C, couple signal inputs and outputs through the HLT100C module and INISO and OUTISO adapters,
respectively. Contact BIOPAC for details. Includes In-line
Transformer (AC100A) and MP System Guide. Specify USA or EURO
power cord.
Specifications
Specifications
Next
IMPORTANT USAGE NOTE
Analog I/O Access
16 channels (front panel) – 3.5mm phone jacks
Amplifier Output Access 16 channels (front panel) – 3.5mm phone jacks
D/A Outputs
2 channels (front panel) – 3.5mm phone jacks
Isolated Power Access
±12 V, +5 V @ 100 ma (back panel) – screw terminals
16 channels (back panel) – screw terminals
Weight
610 g
1 channel (back panel) – screw terminal
Dimensions, H x W x D
19 x 7 11 cm
Power Source
12VDC @ 1 amp (uses AC100A transformer)
Digital I/O Access
Ext. Trigger Access
Isolated Power Access ±12 V, +5 V @ 100 ma (back panel) – screw terminals
Weight
520 g
Catalog No.
Dimensions, H x W x D 19 x 7 x 11 cm
BS4 72-7261
Catalog No.
BS4 72-7260
I104
$
Model
495.00 UIM100C
Product
$
Model
795.00 IPS100C
Product
Isolated Power Supply Module
IPS100C
Universal Interface Module UIM100C
(if purchased separately)
11,000 Specialty Products to Enhance Your Bioresearch
U.S. Toll Free: (800) 272-2775 • Fax: (508) 429-5732 • Online: www.harvardapparatus.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising