Sub-Zero User manual

Sub-Zero  User manual
INTERNATIONAL DESIGN GUIDE
CONTENTS
Built-In Refrigeration
4
Integrated Refrigeration
27
Wine Storage
46
Undercounter Refrigeration
63
Features and specifications indicated
herein and on our website are subject
to change at any time without notice.
Check our website, subzero.com, for
the most up-to-date specifications.
IMPORTANT NOTE
International models from the
factory designed without a transformer require a 220/240 V AC,
50/60 Hz electrical supply, fused
at the correct rating for the unit.
If required by local or national
codes, the power cord can be
easily replaced using the power
inlet device.
International models using a
factory installed transformer
require a 220/240 V AC, 50/60 Hz
electrical supply, fused at the
correct rating for the unit. These
models will come equipped with
Schuko power cords. The power
cord may need to be replaced
depending on local and national
codes. The USA power cord that is
supplied with the product must be
disconnected with the appropriate
transformer output to be
connected in its place.
The information and images in this
guide are the copyright property of
Sub-Zero Freezer Company, Inc.
Neither this book nor any information
or images contained herein may be
copied or used in whole or in part
without the express written permission
of Sub-Zero Freezer Company, Inc.
©Sub-Zero Freezer Company, Inc. all
rights reserved.
SUB-ZERO ® is a registered trademark of Sub-Zero Freezer Company, Inc.
WELCOME TO SUB-ZERO
We make the ultimate built-in, integrated and
undercounter refrigerators, freezers and wine
storage units. We offer more solutions to your
daily design problems of trying to work the
largest appliance into a home without being
obtrusive. Placing refrigeration in the home is no
longer a problem, but, rather, an opportunity to
exercise your creativity.
Sub-Zero has rethought traditional built-in
refrigeration, a category it pioneered, with over
60 years of experience. When our complete line
of configurations—all refrigerator and all freezer,
over-and-under, or side-by-side—are coupled
with overlay or stainless steel design alternatives, the result is unlimited flexibility in satisfying your client‘s needs for residential refrigeration.
Sub-Zero is breaking with conventional ways of
offering Wine Storage for designers and their
clients. Our Built-In and Integrated models, along
with the free-standing Model I424FS, offer
unlimited design and storage capabilities.
Comprehensive installation instructions are
shipped with each model. Refer to those
instructions in preparing and installing all
Sub-Zero products. These instructions along
with product specifications and downloadable
2D and 3D CAD files, as well as pdf files can be
found on our website, subzero.com.
CONTACT
I N F O R M AT I O N
Website:
subzero.com
Created to blend invisibly into your home‘s
decor, the Integrated line lets you incorporate
refrigeration anywhere in the house—the kitchen,
master suite, media room or workout room.
These tall units or two-drawer base refrigerators,
freezers and combination units can be hidden
inside the furniture or cabinetry of your
choosing.
As you follow these instructions, you
will notice warning and caution symbols.
This blocked information is important
for the safe and efficient installation of
Sub-Zero equipment. There are two
types of potential hazards that may
occur during installation.
signals a situation where minor
injury or product damage may occur
if you do not follow instructions.
states a hazard that may cause
serious injury or death if precautions
are not followed.
Another footnote we would like to
identify is IMPORTANT NOTE: This
highlights information that is especially
relevant to a problem-free installation.
3
B U I LT- I N R E F R I G E R AT I O N
Sub-Zero’s Built-In line offers you the most
complete set of design options in built-in refrigeration for all of its models, from the beauty of
the overlay models to the professional treatment
of the wrapped stainless steel doors.
Glass doors are available on our Models I601R,
I611 and I650. They each come in a framed,
overlay and stainless steel design. Model
ICB648PROG also features a glass door in its
classic stainless steel look.
In the illustrations, we have shown the two
different design configurations of the overlay
and stainless steel units applied to Model I695.
Please note how we qualify the different looks
with the model number.
Model I695/O
Overlay
Model I695/S
Classic
Stainless Steel
4
Overlay models will come with no handle
hardware, because the beauty of this design is
that you can match the surrounding cabinetry
hardware; however, we do offer optional handles
as sales accessories. The new ice and water
dispensing Models I685 and I695 are able to
accept overlay panels. Overlay models will come
with a standard 279 mm panel grille that will
accept decorative panel inserts. Models I601R,
I601RG and I601F are only available with the
louvered grille. No panel grille option is available.
All stainless steel models are offered in the
classic stainless steel finish. Stainless steel
models come with a standard 279 mm heavyduty grille, 25 mm diameter stainless steel
handles and a stainless steel kickplate.
All grilles will be offered as options in 25 mm
increments from 254 mm to 381 mm and can be
ordered as sales accessories. Models I601R,
I601RG, I601F, ICB648PRO and ICB648PROG
are the exception and are available only with a
279 mm grille.
An important step in assuring a successful plan
is to make sure that the actual equipment
shipped to your installation site matches the
design you have ordered. Each of these design
options has specific installation requirements,
which means it is vital that the unit match your
planning and space needs.
B U I LT- I N R E F R I G E R AT I O N
A L L R E F R I G E R AT O R | A L L F R E E Z E R
These illustrations represent the full line of
Sub-Zero Built-In models shown in the stainless steel design application with heavy-duty
grille. Models ICB648PRO and ICB648PROG
are available as built-in or free-standing units
in classic stainless steel only.
914 mm
1854
mm
For information regarding specific Built-In
models, refer to the illustrations in this
section. Regardless of the specific design
application, overlay or stainless steel, the
interior specifications of each model are
identical.
914 mm
914 mm
1854
mm
1854
mm
MODEL I601R
MODEL I601RG
MODEL I601F
All Refrigerator
All Refrigerator
with Glass Door
All Freezer
OVER-AND-UNDER
762 mm
With the installation of a harness kit,
these appliances are Star-K compliant
to meet strict religious regulations in
conjunction with specific instructions
found on www.star-k.org. Models
ICB648PRO and ICB648PROG are
Star-K certified from the factory with
no extra wiring harness required. For
details about the harness kit, contact
your Sub-Zero dealer.
2134
mm
762 mm
914 mm
2134
mm
MODEL I611
914 mm
2134
mm
MODEL I611G
2134
mm
MODEL I650
MODEL I650G
with Glass Door
with Glass Door
S I D E - B Y- S I D E
914 mm
2134
mm
MODEL I661
1067 mm
2134
mm
1067 mm
2134
mm
MODEL I642
1219 mm
2134
mm
MODEL I685
Ice | Water
Dispensing
1219 mm
2134
mm
MODEL I632
1219 mm
2134
mm
MODEL I695
Ice | Water
Dispensing
1219 mm
2134
mm
MODEL
ICB648PRO
MODEL
ICB648PROG
Free-Standing
or Built-In
Free-Standing
or Built-In
Comprehensive installation
instructions are shipped with each
model. Refer to those instructions
in preparing and installing all
Sub-Zero products. The instructions
can also be found on our website,
subzero.com.
5
B U I LT- I N F E AT U R E S
Overlay models blend seamlessly into your
overall room design and complement surrounding
cabinetry. You add decorative hardware. Overlay
models come with a panel grille that will accept
decorative panel inserts. The new ice and water
dispensing Models I685 and I695 are also available in the overlay application.
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer.
Stainless steel models feature wrapped doors,
25 mm diameter stainless steel handles and a
heavy-duty grille designed specifically to enhance
the aesthetics of today's professional looking
kitchens. All Built-In stainless steel models are
offered in the classic stainless steel finish.
Dual Refrigeration System. All Built-In combination models have the Sub-Zero dual refrigeration
system, which ensures the freshest food and
energy efficiency at the same time. You have
precise independent control of the refrigerator
and freezer compartments. In addition to two
compressors, the PRO 48 has three separate
evaporators to keep foods fresher longer and
prevent odor transfer.
Glass Door. Model I601RG is an all refrigerator
unit featuring a glass door. Models I611G and
I650G are over-and-under combination units with
a glass door on the refrigerator. These glass door
models come in overlay and stainless steel
designs. The side-by-side Model ICB648PROG
features a glass door on the refrigerator side and
comes in classic stainless steel only.
Stainless Steel. The PRO 48 (Models
ICB648PRO and ICB648PROG) feature stainless
steel construction inside and out with classic
finish for professional strength and beauty.
Ice and Water Dispensing. Models I685 and I695
feature a dispenser that gives you both ice and
chilled water through the refrigerator door.
Built-In Design. True cabinet depth design means
every inch of the interior is easy to see and to
reach. The PRO 48 can be built in or, with the
free-standing accessory kit, used in a freestanding application.
Fresh Food. High-humidity crisper drawer with
removable dividers is large and deep, with
smooth sides for easy cleaning. The top refrigerated drawer on the PRO 48 features a tight-seal,
retracting glass crisper lid that keeps produce
exceptionally humid and fresh.
Electronic Controls. Up-front touch controls
give you digital readings for quick, easy-to-read
reference. The microprocessor provides supreme
control, accurate to within one degree of preset
temperatures, automatic defrosting that senses,
then adapts to your use patterns, and a service
indicator light. The PRO 48 also features exterior
temperature displays.
Advanced Lighting. Bright lighting spreads
even illumination throughout the compartment.
The source of the illumination is concealed. The
PRO 48 top LED lights bathe upper compartments in a soft glow. On the refrigerator side,
channeled sidewall LEDs can even serve as a
door-area night-light for Model ICB648PROG.
Adjustable Shelves. Cantilevered glass shelves
make repositioning quick and easy. They are
easy to clean, spill proof and steel reinforced for
durability. The PRO 48 features glass shelves
with stainless steel trim in the refrigerator and
100% stainless steel shelves in the freezer.
Slide-Out Bins. An exclusive PRO 48 feature—
these versatile stainless steel bins hold small
items, remove easily, and fit neatly under any
shelf.
Door Shelves. All door shelves are adjustable for
complete flexibility and convenience.
Dairy Storage. Dairy compartment is adjustable,
with easy, one-door access, compartment
dividers and a clean design. The dairy shelf is
magnetically sealed to maintain freshness.
Automatic Ice. Ice maker provides high-quality,
crescent-shaped ice that won‘t stick to the side
of the glass.
Energy Efficient. Our solid core doors improve
insulation and structural integrity. Magnetic
gaskets around all doors give extra-tight seals.
Kickplate. Solid, adjustable kickplate gives a true
built-in look and conforms to American Institute
of Architects standards.
6
MODEL I601R
MODEL I601RG
MODEL I601F
A L L R E F R I G E R AT O R
A L L R E F R I G E R AT O R
WITH GLASS DOOR
ALL FREEZER
MODEL OPTIONS
MODEL OPTIONS
MODEL OPTIONS
Overlay Design
I601R/O
Overlay Design
I601RG/O
Overlay Design
I601F/O
Classic Stainless Steel
I601R/S
Classic Stainless Steel
I601RG/S
Classic Stainless Steel
I601F/S
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Overall Width
914 mm
Overall Width
914 mm
Overall Width
914 mm
Overall Height
1854 mm
Overall Height
1854 mm
Overall Height
1854 mm
Overall Depth
610 mm
Overall Depth
610 mm
Overall Depth
610 mm
Refrigerator Capacity
564 L
Refrigerator Capacity
569 L
Freezer Capacity
547 L
Min Height Required
1848 mm
Min Height Required
1848 mm
Min Height Required
1848 mm
Door Swing Clearance
916 mm
Door Swing Clearance
916 mm
Door Swing Clearance
916 mm
Specify Door Swing
LH or RH
Specify Door Swing
LH or RH
Specify Door Swing
LH or RH
Shipping Wt (O)
177 kg
Shipping Wt (O)
181 kg
Shipping Wt (O)
171 kg
Shipping Wt (S)
191 kg
Shipping Wt (S)
195 kg
Shipping Wt (S)
184 kg
R E F R I G E R AT O R F E AT U R E S
R E F R I G E R AT O R F E AT U R E S
F R E E Z E R F E AT U R E S
4 Adjustable Glass Shelves
4 Adjustable Glass Shelves
Automatic Ice Maker
1 Stationary Glass Shelf
1 Stationary Glass Shelf
3 Adjustable Wire Shelves
High-Humidity Compartment with Dividers
High-Humidity Compartment with Dividers
1 Stationary Glass Shelf
Adjustable Roll-Out Deli Basket
Triple-Pane UV Resistant Glass Door
3 Freezer Storage Drawers
3 Adjustable Door Shelves
5 Adjustable Door Shelves
Adjustable Dairy Compartment
Optional Accessory Roll-Out Deli Basket
Available
Egg Container
Egg Container
601RG
MODEL I601R
All models are shown in the stainless
steel design application.
MODEL I601RG
MODEL I601F
ACCESSORIES
Contact your Sub-Zero Dealer
Side panels in white and
classic stainless steel
Roll-out deli basket
(Model I601RG)
Full-length framed handles
Dozen egg container with lid
Decorative overlay handles
Harness kit for Star-K compliance
90˚ and 105˚ door stop kits
7
MODEL I611
MODEL I611G
OVER-AND-UNDER
OVER-AND-UNDER
WITH GLASS DOOR
All models are shown in the stainless
steel design application.
MODEL OPTIONS
MODEL OPTIONS
Overlay Design
I611/O
Overlay Design
I611G/O
Classic Stainless Steel
I611/S
Classic Stainless Steel
I611G/S
S P E C I F I C AT I O N S
8
S P E C I F I C AT I O N S
Overall Width
762 mm
Overall Width
762 mm
Overall Height
2134 mm
Overall Height
2134 mm
Overall Depth
610 mm
Overall Depth
610 mm
Refrigerator Capacity
360 L
Refrigerator Capacity
365 L
Freezer Capacity
110 L
Freezer Capacity
110 L
Min Height Required
2108 mm
Min Height Required
2108 mm
Door Swing Clearance
765 mm
Door Swing Clearance 765 mm
Shipping Wt (O)
195 kg
Shipping Wt (O)
214 kg
Shipping Wt (S)
210 kg
Shipping Wt (S)
216 kg
R E F R I G E R AT O R ( D O O R )
R E F R I G E R AT O R ( D O O R )
3 Adjustable Glass Shelves
3 Adjustable Glass Shelves
1 Stationary Glass Shelf
1 Stationary Glass Shelf
High-Humidity Compartment with Divider
High-Humidity Compartment with Divider
Adjustable Roll-Out Deli Basket
Triple-Pane UV Resistant Glass Door
2 Adjustable Door Shelves
Adjustable Dairy Compartment
Optional Accessory Roll-Out Deli Basket
Available
Egg Container
Egg Container
FREEZER (DRAWER)
FREEZER (DRAWER)
Full-Extension Roll-Out Freezer Drawer
Full-Extension Roll-Out Freezer Drawer
Two-Tier Wire Storage Baskets
Two-Tier Wire Storage Baskets
Automatic Ice Maker
Automatic Ice Maker
MODEL I611
MODEL I611G
MODEL I650
MODEL I650G
OVER-AND-UNDER
OVER-AND-UNDER
WITH GLASS DOOR
ACCESSORIES
MODEL OPTIONS
MODEL OPTIONS
Overlay Design
I650/O
Overlay Design
I650G/O
Classic Stainless Steel
I650/S
Classic Stainless Steel
I650G/S
S P E C I F I C AT I O N S
Optional accessories
are available
through your
Sub-Zero dealer.
S P E C I F I C AT I O N S
Overall Width
914 mm
Overall Width
914 mm
Overall Height
2134 mm
Overall Height
2134 mm
Overall Depth
610 mm
Overall Depth
610 mm
Refrigerator Capacity
445 L
Refrigerator Capacity
453 L
Freezer Capacity
139 L
Freezer Capacity
139 L
Min Height Required
2108 mm
Min Height Required
2108 mm
Door Swing Clearance
916 mm
Door Swing Clearance
916 mm
Shipping Wt (O)
219 kg
Shipping Wt (O)
237 kg
Shipping Wt (S)
234 kg
Shipping Wt (S)
240 kg
R E F R I G E R AT O R ( D O O R )
R E F R I G E R AT O R ( D O O R )
3 Adjustable Glass Shelves
3 Adjustable Glass Shelves
1 Stationary Glass Shelf
1 Stationary Glass Shelf
High-Humidity Compartment with Dividers
High-Humidity Compartment with Dividers
Adjustable Roll-Out Deli Basket
Triple-Pane UV Resistant Glass Door
2 Adjustable Door Shelves
Adjustable Dairy Compartment
Optional Accessory Roll-Out Deli Basket
Available
Egg Container
Egg Container
FREEZER (DRAWER)
FREEZER (DRAWER)
Full-Extension Roll-Out Freezer Drawer
Full-Extension Roll-Out Freezer Drawer
Two-Tier Wire Storage Baskets
Two-Tier Wire Storage Baskets
Automatic Ice Maker
Automatic Ice Maker
ACCESSORIES
Contact your Sub-Zero Dealer
Side panels in white and classic
stainless steel
Panel, louvered or stainless steel
grilles in 25 mm increments from
254 mm to 381 mm high
Full-length framed handles
Decorative overlay handles
MODEL I650
MODEL I650G
Roll-out deli basket
(Models I611G and I650G)
Dozen egg container with lid
Harness kit for Star-K compliance
9
MODEL I661
MODEL I642
MODEL I685
S I D E - B Y- S I D E
S I D E - B Y- S I D E
S I D E - B Y- S I D E
I C E | W AT E R D I S P E N S I N G
MODEL OPTIONS
MODEL OPTIONS
MODEL OPTIONS
Overlay Design
I661/O
Overlay Design
I642/O
Overlay Design
I685/O
Classic Stainless Steel
I661/S
Classic Stainless Steel
I642/S
Classic Stainless Steel
I685/S
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Overall Width
914 mm
Overall Width
1067 mm
Overall Width
1067 mm
Overall Height
2134 mm
Overall Height
2134 mm
Overall Height
2134 mm
Overall Depth
610 mm
Overall Depth
610 mm
Overall Depth
610 mm
Refrigerator Capacity
354 L
Refrigerator Capacity
459 L
Refrigerator Capacity
442 L
Freezer Capacity
249 L
Freezer Capacity
232 L
Freezer Capacity
232 L
Min Height Required
2108 mm
Min Height Required
2108 mm
Min Height Required
2108 mm
Door Swing Clearance
527 mm
Door Swing Clearance
649 mm
Door Swing Clearance
649 mm
Shipping Wt (O)
227 kg
Shipping Wt (O)
245 kg
Shipping Wt (O)
258 kg
Shipping Wt (S)
244 kg
Shipping Wt (S)
264 kg
Shipping Wt (S)
276 kg
R E F R I G E R AT O R F E AT U R E S
R E F R I G E R AT O R F E AT U R E S
R E F R I G E R AT O R F E AT U R E S
4 Adjustable Glass Shelves
4 Adjustable Glass Shelves
4 Adjustable Glass Shelves
1 Stationary Glass Shelf
1 Stationary Glass Shelf
1 Stationary Glass Shelf
High-Humidity Compartment
High-Humidity Compartment
High-Humidity Compartment
1 Storage Drawer
1 Storage Drawer
1 Storage Drawer
Adjustable Roll-Out Deli Basket
Adjustable Roll-Out Deli Basket
Adjustable Roll-Out Deli Basket
3 Adjustable Door Shelves
3 Adjustable Door Shelves
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Adjustable Dairy Compartment
Adjustable Dairy Compartment
Egg Container
Egg Container
Egg Container
F R E E Z E R F E AT U R E S
F R E E Z E R F E AT U R E S
F R E E Z E R F E AT U R E S
Automatic Ice Maker
Automatic Ice Maker
Automatic Ice Maker
2 Adjustable Wire Shelves
3 Adjustable Wire Shelves
2 Adjustable Wire Shelves
1 Stationary Solid Shelf
1 Stationary Solid Shelf
1 Stationary Wire Shelf
4 Storage Drawers
3 Storage Drawers
3 Storage Drawers
5 Adjustable Door Shelves
5 Adjustable Door Shelves
5 Adjustable Door Shelves
2 Juice Can Shelves
MODEL I661
10
MODEL I642
MODEL I685
MODEL I632
MODEL I695
S I D E - B Y- S I D E
S I D E - B Y- S I D E
I C E | W AT E R D I S P E N S I N G
All models are shown in the stainless
steel design application.
MODEL OPTIONS
MODEL OPTIONS
Overlay Design
I632/O
Overlay Design
I695/O
Classic Stainless Steel
I632/S
Classic Stainless Steel
I695/S
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Overall Width
1219 mm
Overall Width
1219 mm
Overall Height
2134 mm
Overall Height
2134 mm
Overall Depth
610 mm
Overall Depth
610 mm
Refrigerator Capacity
535 L
Refrigerator Capacity
515 L
Freezer Capacity
278 L
Freezer Capacity
278 L
Min Height Required
2108 mm
Min Height Required
2108 mm
Door Swing Clearance
743 mm
Door Swing Clearance
743 mm
Shipping Wt (O)
264 kg
Shipping Wt (O)
277 kg
Shipping Wt (S)
286 kg
Shipping Wt (S)
298 kg
R E F R I G E R AT O R F E AT U R E S
R E F R I G E R AT O R F E AT U R E S
4 Adjustable Glass Shelves
4 Adjustable Glass Shelves
1 Stationary Glass Shelf
1 Stationary Glass Shelf
High-Humidity Compartment with Divider
High-Humidity Compartment with Divider
2 Storage Drawers
2 Storage Drawers
Adjustable Roll-Out Deli Basket
Adjustable Roll-Out Deli Basket
3 Adjustable Door Shelves
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Adjustable Dairy Compartment
Egg Container
Egg Container
F R E E Z E R F E AT U R E S
F R E E Z E R F E AT U R E S
Automatic Ice Maker
Automatic Ice Maker
3 Adjustable Wire Shelves
2 Adjustable Wire Shelves
1 Stationary Solid Shelf
1 Stationary Wire Shelf
3 Storage Drawers
3 Storage Drawers
5 Adjustable Door Shelves
5 Adjustable Door Shelves
2 Juice Can Shelves
ACCESSORIES
Contact your Sub-Zero Dealer
Side panels in white and classic
stainless steel
Panel, louvered or stainless steel
grilles in 25 mm increments from
254 mm to 381 mm high
Full-length framed handles
Decorative overlay handles
90˚ and 105˚ door stop kits
MODEL I632
MODEL I695
Dozen egg container with lid
Harness kit for Star-K compliance
11
MODEL ICB648PRO
MODEL ICB648PROG
S I D E - B Y- S I D E
B U I LT- I N O R F R E E - S TA N D I N G
S I D E - B Y- S I D E
WITH GLASS DOOR
B U I LT- I N O R F R E E - S TA N D I N G
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Overall Width
1219 mm
Overall Width
1219 mm
Overall Height
2134 mm
Overall Height
2134 mm
Overall Depth
657 mm
Overall Depth
657 mm
Refrigerator Capacity
521 L
Refrigerator Capacity
521 L
Freezer Capacity
331 L
Freezer Capacity
331 L
Min Height Required
2121 mm
Min Height Required
2121 mm
Door Swing Clearance
730 mm
Door Swing Clearance
730 mm
Shipping Weight
390 kg
Shipping Weight
397 kg
R E F R I G E R AT O R
R E F R I G E R AT O R
(Door and Two Drawers)
(Door and Two Drawers)
3 Adjustable Glass Shelves
3 Adjustable Glass Shelves
1 Stationary Glass Shelf
1 Stationary Glass Shelf
2 Adjustable Slide-Out Stainless Steel Bins
2 Adjustable Slide-Out Stainless Steel Bins
1 Crisper Lid
1 Crisper Lid
Dividers for Drawers Included
Dividers for Drawers Included
Triple-Pane UV Resistant Glass Door
FREEZER
FREEZER
(Door and Two Drawers)
(Door and Two Drawers)
Automatic Ice Maker
Automatic Ice Maker
3 Adjustable Stainless Steel Shelves
3 Adjustable Stainless Steel Shelves
1 Stationary Stainless Steel Shelf
1 Stationary Stainless Steel Shelf
1 Stainless Steel Ice Bucket
1 Stainless Steel Ice Bucket
MODEL ICB648PRO
MODEL ICB648PROG
ACCESSORIES
Contact your Sub-Zero Dealer
90˚ door stop kit—right or left
hinge
Dozen egg container with lid
Slide-out stainless steel
refrigerator bin
Refrigerator drawer dividers
Classic stainless steel side panel
Free-standing kit—includes two
stainless steel side panels and
top lid
12
PLANNING INFORMATION
ELECTRICAL REQUIREMENTS
Although the Sub-Zero Built-In line offers a wide
range of designs and configurations, the basic
planning considerations for all models have
much in common. As you integrate Built-In
models into your overall plan, review installation
requirements for your particular model(s). The
Installation Specifications illustrations provide
planning information for all Built-In models—
overlay and stainless steel.
International models from the factory designed
without a transformer require a 220/240 V AC,
50/60 Hz electrical supply, fused at the correct
rating for the unit. If required by local or national
codes, the power cord can be easily replaced
using the power inlet device.
Allow the door(s) to open a minimum of 90˚ or
you‘ll have problems removing drawers. With the
door opening at 90˚, you may have to move
drawers slightly to clear the door interior.
For corner installations, allow for a minimum
76 mm filler so that the door can open to 90˚.
If you‘re using raised panels, consider using a
wider filler.
When units are installed side by side, a filler strip
is recommended. The width of this filler strip will
vary depending on the configuration and panels
you use.
Be sure to add the filler strip width to your
finished rough opening dimension. In any
installation of two units side by side without a
filler strip, add an additional 13 mm to your
combined numbers. This will allow for the
proper width.
IMPORTANT NOTE: Refer to the full-scale illustrations at the end of this section for specifics
on door openings and filler size alternatives.
International models using a factory installed
transformer require a 220/240 V AC, 50/60 Hz
electrical supply, fused at the correct rating for
the unit. These models will come equipped with
Schuko power cords. The power cord may need
to be replaced depending on local and national
codes. The USA power cord that is supplied
with the product must be disconnected with the
appropriate transformer output to be connected
in its place.
IMPORTANT NOTE: The electrical outlet must
be grounded. The outlet must be flush with the
back wall. Refer to the Installation Specifications
illustration for your model for exact placement.
IMPORTANT NOTE: A ground fault circuit
interrupter (GFCI) is not recommended and may
cause interruption of operation.
PLUMBING CONSIDERATIONS
For Built-In models with an automatic ice maker,
rough in the water supply line. Connect a
6.35 mm OD copper line to the house supply,
being sure to use an easily accessible shut-off
valve between the supply and the refrigerator.
Do not use self-piercing valves. A saddle valve kit
(4200880) is available from your Sub-Zero dealer.
For Built-In models, a line filter is required when
water conditions have a high sediment content.
The ice maker operates on water pressure of 1.4
bar to 6.9 bar.
MODEL OPTIONS
Model I601R
914 mm
All Refrigerator
Model I601RG
914 mm
All Refrigerator
with Glass Door
Model I601F
914 mm
All Freezer
Model I611
762 mm
Over-and-Under
Model I611G
762 mm
Over-and-Under
with Glass Door
Model I650
914 mm
Over-and-Under
Model I650G
914 mm
Over-and-Under
with Glass Door
Model I661
914 mm
Side-by-Side
Model I642
1067 mm
Side-by-Side
Model I685
1067 mm
Side-by-Side
Ice | Water Dispensing
Model I632
1219 mm
Side-by-Side
IMPORTANT NOTE: In some cases a reverse
osmosis water filter system may not be able to
maintain the minimum water pressure consistently.
Model I695
1219 mm
Side-by-Side
Ice | Water Dispensing
IMPORTANT NOTE: A reverse osmosis system
can be used with Models ICB648PRO and
ICB648PROG, provided there is constant water
pressure of 1.4 bar to 8.3 bar supplied to the
unit at all times.
Model ICB648PRO
1219 mm
Side-by-Side
Built-In or Free-Standing
The water line should be routed up through the
floor within 13 mm from the back wall and no
higher than 76 mm off the floor. If you have to
come through the wall, make sure the water line
is no more than 76 mm from the floor.
Model ICB648PROG
1219 mm
Side-by-Side
with Glass Door
Built-In or Free-Standing
Regardless of the routing, allow 1 m of excess
copper tubing to remain outside the wall or floor
for easy connection to the unit. Refer to Installation Specification illustrations.
13
OVERALL DIMENSIONS
All Refrigerator | All Freezer Models
A L L R E F R I G E R AT O R
ALL FREEZER
1854 mm
1854 mm
1854 mm
Model I601R
All Refrigerator
Model I601RG
All Refrigerator
with Glass Door
Model I601F
All Freezer
914 mm
914 mm
914 mm
Model I601R
Model I601RG
Model I601F
All Refrigerator
All Refrigerator
with Glass Door
All Freezer
Width
914 mm
Width
914 mm
Width
914 mm
Height
1854 mm
Height
1854 mm
Height
1854 mm
Depth
610 mm
Depth
610 mm
Depth
610 mm
610 mm
Illustrations shown in stainless steel design.
I N S TA L L AT I O N
Refer to the
installation instructions shipped with
each Sub-Zero
product for detailed
specifications.
Refer to the fullscale illustrations at
the end of this
section for specifics
on door openings
and other
specifications.
I N S TA L L AT I O N S P E C I F I C AT I O N S
All Refrigerator | All Freezer Models
EXTEND
WATER LINE
APPROX 914 mm
FROM BACK WALL
(I601F ONLY)
610 mm
ROUGH
OPENING
DEPTH
Models I601R and I601RG, which do not
have an ice maker, will not require the water
line connection.
SHUT-OFF
VALVE
Dimensions are for finished rough openings.
TOP VIEW
Door swing clearances are based on
stainless steel door and handle dimensions.
10 mm
FRAME
EXTENSION
606 mm
BEHIND
FRAME
902 mm
ROUGH OPENING WIDTH
90˚
916 mm
1848 mm
1848 mm
ROUGH OPENING
HEIGHT TO
FINISHED
FLOORING
MINIMUM HEIGHT
REQUIRED TO
FINISHED
FLOORING
(LEVELERS IN)
LOCATE ELECTRICAL
WITHIN ENTIRE SHADED AREA
LOCATE WATER SUPPLY
WITHIN BOTTOM SHADED
AREA ONLY (I601F ONLY)
279
mm
610 mm
152
mm
E
76
mm
W
FRONT VIEW
14
OVERALL DIMENSIONS
Over-and-Under Refrigerator / Freezer Models
OVER-AND-UNDER
2134 mm
2134 mm
2134 mm
2134 mm
Model I611
Model I611G
with Glass Door
Model I650
Model I650G
with Glass Door
762 mm
Model I611
762 mm
Model I611G
914 mm
914 mm
Model I650
610 mm
Model I650G
with Glass Door
with Glass Door
Width
762 mm
Width
762 mm
Width
914 mm
Width
914 mm
Height
2134 mm
Height
2134 mm
Height
2134 mm
Height
2134 mm
Depth
610 mm
Depth
610 mm
Depth
610 mm
Depth
610 mm
Illustrations shown in stainless steel design.
I N S TA L L AT I O N
I N S TA L L AT I O N S P E C I F I C AT I O N S
Refer to the
installation instructions shipped with
each Sub-Zero
product for detailed
specifications.
Over-and-Under Refrigerator / Freezer Models
EXTEND
WATER LINE
APPROX 914 mm
FROM BACK WALL
610 mm
ROUGH
OPENING
DEPTH
Model I611
A) Rough Opening Width
749 mm
B) Min Door Clearance
765 mm
SHUT-OFF
VALVE
TOP VIEW
Model I611G
A) Rough Opening Width
749 mm
B) Min Door Clearance
765 mm
178
mm
E
10 mm
152
mm
Model I650
A) Rough Opening Width
902 mm
B) Min Door Clearance
916 mm
FRAME
EXTENSION
90˚
A
902 mm
B) Min Door Clearance
916 mm
ROUGH OPENING WIDTH
2108 mm
Dimensions are for finished rough openings.
Door swing clearances are based on
stainless steel door and handle dimensions.
BEHIND
FRAME
LOCATE ELECTRICAL
WITHIN SHADED AREA
Model I650G
A) Rough Opening Width
606 mm
MIN HEIGHT
REQUIRED TO
FINISHED
FLOORING
(LEVELERS IN)
B
1918
mm
2127 mm
ROUGH OPENING
HEIGHT TO
FINISHED
FLOORING WITH
STANDARD
279 mm GRILLE
LOCATE WATER SUPPLY
WITHIN SHADED AREA
76
mm
457 mm
152
mm
Refer to the fullscale illustrations at
the end of this
section for specifics
on door openings
and other
specifications.
W
FRONT VIEW
15
OVERALL DIMENSIONS
Side-by-Side Refrigerator | Freezer Models
2134 mm
914 mm
Model I661
1067 mm
1067 mm
Model I685
Model I642
1219 mm
1219 mm
Model I632
610 mm
Model I695
Ice | Water Dispensing
Ice | Water Dispensing
Width
914 mm
Width
1067 mm
Width
1067 mm
Width
1219 mm
Width
1219 mm
Height
2134 mm
Height
2134 mm
Height
2134 mm
Height
2134 mm
Height
2134 mm
Depth
610 mm
Depth
610 mm
Depth
610 mm
Depth
610 mm
Depth
610 mm
Illustrations shown in stainless steel design.
S I D E - B Y- S I D E
I N S TA L L AT I O N S P E C I F I C AT I O N S
Model I661
Side-by-Side Refrigerator | Freezer Models
Model I642
EXTEND
WATER LINE
APPROX 914 mm
FROM BACK WALL
610 mm
Model I685
Ice | Water Dispensing
Model I661
A) Rough Opening Width
902 mm
Model I632
B) Min Door Clearance
527 mm
Model I695
Ice | Water Dispensing
Model I642
A) Rough Opening Width
B) Min Door Clearance
ROUGH
OPENING
DEPTH
SHUT-OFF
VALVE
TOP VIEW
1054 mm
178
mm
649 mm
E
152
mm
Model I685
10 mm
FRAME
EXTENSION
606 mm
BEHIND
FRAME
A) Rough Opening Width
B) Min Door Clearance
LOCATE ELECTRICAL
WITHIN SHADED AREA
1054 mm
649 mm
Model I632
A) Rough Opening Width
90˚
B
B) Min Door Clearance
A
743 mm
2108 mm
Model I695
A) Rough Opening Width
B) Min Door Clearance
ROUGH OPENING WIDTH
1206 mm
1206 mm
743 mm
MIN HEIGHT
REQUIRED TO
FINISHED
FLOORING
(LEVELERS IN)
1918
mm
2127 mm
ROUGH OPENING
HEIGHT TO
FINISHED
FLOORING WITH
STANDARD
279 mm GRILLE
I N S TA L L AT I O N
Dimensions are for finished rough openings.
Refer to the
installation instructions shipped with
each Sub-Zero
product for detailed
specifications.
Door swing clearances are based on
stainless steel door and handle dimensions.
LOCATE WATER SUPPLY
WITHIN SHADED AREA
76
mm
457 mm
W
FRONT VIEW
16
152
mm
OVERALL DIMENSIONS
PRO 48 Side-by-Side Refrigerator | Freezer Models
2134 mm
PRO 48
S I D E - B Y- S I D E
606 mm
Model ICB648PRO
Built-In or Free-Standing
Model ICB648PROG
with Glass Door
Built-In or Free-Standing
1219 mm
657 mm
1219 mm
766 mm
Model ICB648PRO
Model ICB648PROG
with Glass Door
Width
1219 mm
Width
1219 mm
Height
2134 mm
Height
2134 mm
Depth
606 mm*
657 mm**
Depth
606 mm*
657 mm**
*Depth from behind face frame to back of unit for standard installation.
**Depth from front of face frame to back of unit for flush installation.
I N S TA L L AT I O N
I N S TA L L AT I O N S P E C I F I C AT I O N S
PRO 48 Side-by-Side Refrigerator | Freezer Models
Built-In or Free-Standing
Refer to the
installation instructions shipped with
each Sub-Zero
product for detailed
specifications.
MIN 914 mm
1/4" COPPER
WATER LINE
ROUGH
OPENING DEPTH
610 mm
STANDARD
Models ICB648PRO and ICB648PROG can be
used free-standing or installed as a standard
or flush built-in application. For standard
built-in installations, the face frame of the
unit will extend 51 mm beyond cabinetry.
In flush built-in installations, the front of the
face frame will be flush with surrounding
cabinetry.
660 mm
SHUT-OFF
VALVE
FLUSH
TOP VIEW
178
mm
E
152
mm
Dimensions are for finished rough openings.
LOCATE ELECTRICAL
WITHIN SHADED AREA
ROUGH
OPENING WIDTH
606 mm
657 mm
BEHIND
FACE
FRAME
TO FRONT
OF FACE
FRAME
521 mm
730 mm
1206 mm STANDARD
1219 mm FLUSH
MIN HEIGHT
REQUIRED
TO FINISHED
FLOORING
(LEVELERS IN)
ROUGH
OPENING HEIGHT
TO FINISHED
FLOORING
2121 mm
2127 mm
STANDARD
STANDARD
2127 mm
2137 mm
FLUSH
FLUSH
1918 mm
1219 mm
LOCATE WATER SUPPLY
WITHIN SHADED AREA
152
mm
76 mm
W
132
mm
FRONT VIEW
17
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer.
18
ANTI-TIP BLOCKING KIT
ADDING PANELS
To prevent the unit from tipping forward and to
provide a stable installation, the unit must be
secured in place with an anti-tip blocking kit. If
there is a solid soffit above the unit with clearance between the unit and the soffit of 25 mm
or less, you won‘t need to block the unit. But for
installations with clearances of more than 25
mm, you must block the unit with the anti-tip
blocking kit (wood block and hardware) provided
with each Sub-Zero Built-In model. Refer to the
Built-In Installation Guide packed with the appliance, which provides step-by-step procedures
for making sure the unit is installed properly.
In your plan for panels, be sure you are working
with the Sub-Zero panel design family called for
in your design. If you have chosen the stainless
steel design, the unit will be shipped complete
with wrapped stainless steel doors and handle
hardware. You will not have to install door
panels.
Specifications on the following pages provide
panel dimensions and installation considerations
for overlay door panels.
Side panels can be used with the overlay and
stainless steel design applications. Refer to
specifications on page 20.
OVERLAY DOOR PANELS
If you and your client have ordered an overlay
design model, you will be adding panels to give
the unit the custom Sub-Zero look. The overlay
panel design option is available on all Built-In
units except Models ICB648PRO and
ICB648PROG.
For exact door panel dimensions for Built-In
overlay models, refer to the Overlay Panel Specifications on pages 22–23.
The overlay design allows decorative panels to
cover the door trim for a more seamless
appearance that blends with the design of the
room. To achieve this look, the most common
way is to work with three panels—the decorative
overlay panel, a 3 mm spacer panel and a 6 mm
backer panel. Depending on your cabinet manufacturer, this could be one panel routed for
different dimensions or, more likely, three different panels.
Regardless of the physical construction of the
panels (routing or three-panel assembly), you will
need to follow the Overlay Panel Specifications
on the following pages for exact sizing and panel
placement to ensure a proper fit.
Illustration 3 is a cross section view of the threepanel assembly showing placement of the door,
drawer or grille trim. Illustration 4 shows a rear
view of the three-panel assembly and critical
dimensions, standard for all models.
Spacer Panel
Overlay Panel
IMPORTANT NOTE: Keep in mind that the
Sub-Zero door panels have the potential for
hitting adjacent cabinets and/or countertops
when they are opened. You need to be aware of
your surrounding cabinetry and space limitations
when using the overlay models. Refer to the fullscale illustrations at the end of this section.
If you are using an overlay door panel with
Model I611, I611G, I650 or I650G, it is necessary
to rout a space for the unit‘s lower hinge plate
so it does not strike the door panel. Refer to
illustration 5.
For Models I611, I611G, I650 and I650G, you will
minimize the reveal between the bottom of the
overlay door panel and the top of the overlay
drawer panel. Refer to illustration 6.
The overlay door
panel assembly
must be a minimum
of16 mm thick
and cannot exceed
23 kg.
IMPORTANT NOTE: If you choose not to rout a
space for the lower hinge plate, you can reduce
the total height of the overlay panel (decorative
panel only) by 13 mm.
Do not exceed the overlay decorative panel
dimensions for Models I611, I611G, I650 or
I650G listed on page 22. If you try to make
the reveal tighter between the door and
drawer panels, the panels may hit when
opening and closing, causing possible
damage to the panels and the Sub-Zero unit.
Overlay Panel
Overlay Panel
Spacer Panel
6 mm Backer Panel
3
mm
PANEL
REQUIREMENTS
Backer
Panel
Spacer Panel
Overlay Panel
Spacer Panel
8
mm
6 mm Backer Panel
8 mm min
4 mm
2 mm
Illus. 3
Door / Drawer/
Grille Trim
76 mm
Backer
Panel
~19
mm
3 mm 6 mm
Illus. 4
13
mm
10 mm
Illus. 5
21
mm
Bottom Edge –
Hinge Side
(rear view)
13 mm
Illus. 6
19
OVERLAY DOOR PANELS
I N S TA L L AT I O N
To install overlay
panels, see the
detailed procedures
outlined in the
Sub-Zero Built-In
Installation Guide.
For glass door Models I601RG, I611G and I650G,
the refrigerator door panel must include a cutout to accommodate the window. Refer to the
Overlay Panel Specifications for Models I601RG,
I611G and I650G on page 22.
Illustration 8 shows how you can box out a
landing space for the bezel using stiles and rails
to create this space. Again, keep in mind, that
the total thickness of the panel at this level must
not exceed 29 mm.
IMPORTANT NOTE: On glass door models, the
glass portion of the door must be exposed and
not covered by any part of the panel.
OVERLAY PANEL GRILLE
For Models I685 and I695, the refrigerator door
panel must include a cut-out to accommodate
the glasswell and bezel. The thickness of the
panel in this area can range from 6 mm to a
maximum of 29 mm.
IMPORTANT NOTE: Regardless of the thickness
of the overlay panel for Model I685 or I695, you
must plan for a flat ’landing’ space for the
decorative bezel surrounding the glasswell area.
Refer to page 23 for exact cut-out dimensions of
the glasswell area in the overlay, spacer and
backer panels. This ’landing’ area can be accomplished in a number of different ways. We are
showing two in Illustrations 7 and 8 below.
Illustration 7 shows how you can recess the
bezel to the inset panel. You must rout out a
space to accommodate the 327 mm height of
the bezel. Also keep in mind that the amount of
material you will rout out of the stile will vary
because of the thickness of this element.
However, the width of the stile immediately
adjacent to the bezel must be 37 mm. DO NOT
cut the entire stile to this dimension. In this illustration you can see that rails above and below
the bezel give this a finished look. Make sure
that the bezel is not supporting weight from
the panel.
Overlay grille panels for the panel grille match
the design of the door panels. Overlay units,
except Models I601R, I601RG and I601F, come
standard with an 279 mm panel grille. Optional
grilles are available in 25 mm height increments
from 254 mm to 381 mm. Overlay grille panel
specifications for the panel grille are listed on
page 23. Also refer to illustration 4 on page 19
for additional overlay panel dimensions.
Do not exceed the panel dimensions listed
for the appropriate overlay grille panel you
are specifying. The decorative panel cannot
be any larger or it may restrict the airflow
to the compressor area and cause problems
with the operation of the Sub-Zero unit.
Routing
Required
Glasswell
Cut-Out
327
mm
37 mm
Width
of Stile
Adjacent
to Bezel
Illus. 7
20
Height
of Bezel
43 mm
Edge of
Panel to
Cut-Out
Illus. 8
HANDLE HARDWARE
SIDE PANELS
Overlay models come without handle hardware.
The beauty of this design is that you can match
the surrounding cabinet hardware. You or the
cabinet manufacturer must provide handle
hardware to match the overall decorating
scheme.
Side panels can be used with the overlay and
stainless steel design applications. When
planning for side panels with the installation of a
Built-In model, you need to be aware of space
configuration to achieve a pleasing fit. Depending on the exact panel you are using with your
unit, the height of the panel will vary.
The handle hardware must be installed before
installing the panel assembly. Use larger D-style
handles. If screws with thick heads are used,
the screws will need to be countersunk into the
door before the panel is put into place.
IMPORTANT NOTE: Sub-Zero does not recommend using single pull knobs on any of its BuiltIn models.
For overlay Models I685 and I695, mounting
placement of the refrigerator door handle must
assure proper access to the glasswell and
adequate clearance under the handle. Illustration
8 shows placement of the refrigerator door
handle in relationship to the glasswell bezel on
stainless steel models.
Cut-outs around the toe kick and grille area are
required if a 6 mm thick panel will be inserted
into the main frame channel. The panel will need
to be 610 mm deep. If a 10 mm thick panel is
used, the panel will abut the main frame and
should be 606 mm deep. Refer to illustrations
9–11 below for placement of toe kick and grille
area cut-outs for your specific model. These
dimensions do not apply to Models ICB648PRO
and ICB648PROG.
The toe kick area may or may not be cut out
depending on the look you want to achieve.
IMPORTANT NOTE: The use of side panels may
change the width of your rough opening.
Optional stainless steel handles are available in a
variety of diameters and lengths, as are handles
to match the color and style of Wolf ovens.
Contact your Sub-Zero dealer for specifics.
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer.
I N S TA L L AT I O N
To install overlay
panels, see the
detailed procedures
outlined in the
Sub-Zero Built-In
Installation Guide.
Refer to the full-scale illustrations at the end of
this section for handle hardware considerations.
25 mm
Glasswell
Profile
51 mm
337 mm
337 mm
6 mm
6 mm
606 mm
606 mm
606 mm
BEHIND FRAME
BEHIND FRAME
BEHIND FRAME
Handle
Profile
Illus. 8
6 mm
76 mm
102 mm
102 mm
102 mm
76 mm
Illus. 9—Models I601R,
I601RG and I601F
76 mm
Illus. 10—Models I611, I611G,
I650 and I650G
76 mm
Illus. 11—Models I661, I642,
I632, I685 and I695
21
O V E R L AY D O O R PA N E L S P E C I F I C AT I O N S
O V E R L AY D O O R PA N E L S P E C I F I C AT I O N S
All Refrigerator | All Freezer Overlay (O) Models
Over-and-Under Overlay (O) Models
Model I601R
W
H
Model I611
W
H
Refrigerator Overlay Panel
875 mm
1505 mm
Refrigerator Overlay Panel
722 mm
1241 mm
Refrigerator Spacer Panel
851 mm
1481 mm
Refrigerator Spacer Panel
699 mm
1205 mm
Refrigerator Backer Panel
867 mm
1497 mm
Refrigerator Backer Panel
714 mm
1221 mm
Freezer Overlay Panel
722 mm
475 mm
Model I601RG
W
H
Freezer Spacer Panel
699 mm
451 mm
Refrigerator Overlay Panel
875 mm
1505 mm
Freezer Backer Panel
714 mm
467 mm
Refrigerator Spacer Panel
851 mm
1481 mm
Refrigerator Backer Panel
867 mm
1497 mm
Model I611G
W
H
Window Cut-out Dimensions
646 mm
1048 mm
Refrigerator Overlay Panel
722 mm
1241 mm
C) 114 mm
D) 343 mm
Refrigerator Spacer Panel
699 mm
1205 mm
Refrigerator Backer Panel
714 mm
1221 mm
Freezer Overlay Panel
722 mm
475 mm
Freezer Spacer Panel
699 mm
451 mm
Freezer Backer Panel
714 mm
467 mm
Window Cut-out Location
Model I601F
W
H
Freezer Overlay Panel
875 mm
1505 mm
Freezer Spacer Panel
851 mm
1481 mm
Freezer Backer Panel
867 mm
1497 mm
Window Cut-out Dimensions
Window Cut-out Location
IMPORTANT NOTE: Panel specifications are for Built-In overlay (O)
models.
494 mm
1000 mm
C) 114 mm
D) 127 mm
Model I650
W
H
Refrigerator Overlay Panel
875 mm
1241 mm
Refrigerator Spacer Panel
851 mm
1205 mm
Refrigerator Backer Panel
867 mm
1221 mm
Freezer Overlay Panel
875 mm
475 mm
Freezer Spacer Panel
851 mm
451 mm
Freezer Backer Panel
867 mm
467 mm
Model I650G
W
H
Refrigerator Overlay Panel
875 mm
1241 mm
Refrigerator Spacer Panel
851 mm
1205 mm
Refrigerator Backer Panel
867 mm
1221 mm
Freezer Overlay Panel
875 mm
475 mm
Freezer Spacer Panel
851 mm
451 mm
Freezer Backer Panel
867 mm
467 mm
Window Cut-out Dimensions
Window Cut-out Location
646 mm
1000 mm
C) 114 mm
D) 127 mm
IMPORTANT NOTE: Panel specifications are for Built-In overlay (O)
models.
C
C
C
C
C
C
H
H
H
H
D
D
22
W
W
Models I601R
and I601F
Model I601RG
H
W
Models I611 and
I650
H
W
Models I611G and
I650G
O V E R L AY D O O R PA N E L S P E C I F I C AT I O N S
OVERLAY GRILLE PANEL
Side-by-Side Overlay (O) Models
Overlay (O) Models
Width Dimensions
Model I661
W
H
Models I611 and I611G
W
Refrigerator Overlay Panel
494 mm
1727 mm
Overlay Panel Width
722 mm
Refrigerator Spacer Panel
470 mm
1703 mm
Spacer Panel Width
699 mm
Refrigerator Backer Panel
486 mm
1719 mm
Backer Panel Width
714 mm
Freezer Overlay Panel
379 mm
1727 mm
Freezer Spacer Panel
356 mm
1703 mm
Models I650, I650G, I661
W
1719 mm
Overlay Panel Width
875 mm
Spacer Panel Width
851 mm
Backer Panel Width
867 mm
Freezer Backer Panel
371 mm
Model I642
W
H
Refrigerator Overlay Panel
618 mm
1727 mm
Refrigerator Spacer Panel
594 mm
1703 mm
Models I642 and I685
W
Refrigerator Backer Panel
610 mm
1719 mm
Overlay Panel Width
1027 mm
Freezer Overlay Panel
405 mm
1727 mm
Spacer Panel Width
1003 mm
Freezer Spacer Panel
381 mm
1703 mm
Backer Panel Width
1019 mm
Freezer Backer Panel
397 mm
1719 mm
Models I632 and I695
W
1180 mm
Model I685
W
H
Overlay Panel Width
Refrigerator Overlay Panel
618 mm
1727 mm
Spacer Panel Width
1156 mm
Backer Panel Width
1172 mm
Refrigerator Spacer Panel
594 mm
1703 mm
Refrigerator Backer Panel
610 mm
1719 mm
Freezer Overlay Panel
405 mm
1727 mm
Freezer Spacer Panel
381 mm
1703 mm
254 mm Grille
H
1719 mm
Overlay Panel Height
235 mm
Spacer Panel Height
211 mm
Backer Panel Height
227 mm
Freezer Backer Panel
Glasswell Cut-out Dimensions
397 mm
150 mm
315 mm
E) 43 mm
F) 730 mm
Glasswell Location (Spacer)
E) 31 mm
F) 718 mm
279 mm Grille (standard)
H
Glasswell Location (Backer)
E) 39 mm
F) 726 mm
Overlay Panel Height
260 mm
Spacer Panel Height
237 mm
Model I632
W
H
Backer Panel Height
252 mm
Refrigerator Overlay Panel
711 mm
1727 mm
305 mm Grille Height
H
Refrigerator Spacer Panel
687 mm
1703 mm
Overlay Panel Height
286 mm
Refrigerator Backer Panel
703 mm
1719 mm
Spacer Panel Height
262 mm
Freezer Overlay Panel
464 mm
1727 mm
Backer Panel Height
278 mm
Freezer Spacer Panel
440 mm
1703 mm
330 mm Grille
H
Freezer Backer Panel
456 mm
1719 mm
Overlay Panel Height
311 mm
Spacer Panel Height
287 mm
Model I695
W
H
Backer Panel Height
303 mm
Refrigerator Overlay Panel
711 mm
1727 mm
Refrigerator Spacer Panel
687 mm)
1703 mm
356 mm Grille
H
Refrigerator Backer Panel
703 mm
1719 mm
Overlay Panel Height
337 mm
Spacer Panel Height
313 mm
Backer Panel Height
329 mm
381 mm Grille
H
Overlay Panel Height
362 mm
Spacer Panel Height
338 mm
Backer Panel Height
354 mm
464 mm
1727 mm
Freezer Spacer Panel
440 mm
1703 mm
Freezer Backer Panel
456 mm
1719 mm
Glasswell Cut-out Dimensions
150 mm
315 mm
Glasswell Location (Overlay)
E) 43 mm
F) 730 mm
Glasswell Location (Spacer)
E) 31 mm
F) 718 mm
Glasswell Location (Backer)
E) 39 mm
F) 726 mm
IMPORTANT NOTE: Panel specifications are for Built-In overlay (O)
models.
For Models I685 and I695, panel thickness in the glasswell area can
range from 6 mm to a maximum of 29 mm. If the panel is thicker, you
must rout out a minimum 6 mm flat landing area to accommodate the
bezel surrounding the glasswell.
Panel specifications
are for Built-In
overlay (O) models.
To install overlay
panels, see the
detailed procedures
outlined in the
Sub-Zero Built-In
Installation Guide.
Height Dimensions
Glasswell Location (Overlay)
Freezer Overlay Panel
OVERLAY PANELS
H
W
W
Models I661, I642
and I632
E
H
F
W
W
Models I685 and I695
H
For grille panel size, use width dimensions
listed for your model and height dimensions
for grille option. 279 mm grille is standard.
W
Overlay grille panel
Panel grille is available for all overlay units
except Models I601R, I601RG and I601F.
23
PANEL AND HANDLE PROFILE – OVERLAY AND STAINLESS STEEL APPLICATION
STANDARD STAINLESS STEEL HANDLE
1"
51
mm
76
mm
32 mm PANEL
25 mm PANEL
19 mm PANEL
16 mm PANEL
13 mm PANEL
6 mm PANEL
6 mm APPROXIMATE THICKNESS OF WRAPPED STAINLESS STEEL DOOR
DOOR
NOTE: FOR OVERLAY APPLICATIONS, OPTIONAL STAINLESS STEEL HANDLE
MUST BE MOUNTED ON PANEL MINIMUM 16 mm THICK.
The full-scale illustration above shows
handle placement for the standard
stainless steel handle on the wrapped
stainless steel door and on overlay
panel applications shown in the dashed
line.
IMPORTANT NOTE: For overlay applications, the panel must be a minimum of
16 mm thick to support mounting the
handle hardware.
For overlay applications, mount door
handles close to the opening edge of
the door for ease of opening.
24
PANEL AND HANDLE PROFILE – 130˚ DOOR OPENING
The full-scale illustration shows the
panel and handle profile for 130˚ door
opening with a 51 mm filler strip.
Interference of door panels with
handles at maximum door swing may
require the use of an optional 90˚ door
stop available through your Sub-Zero
dealer.
130˚ DOOR OPENING
WITH 51 mm FILLER STRIP
SUB-ZERO UNIT
SUB-ZERO UNIT
(TOP VIEW)
FILLER STRIP
51 mm
ALLOW FOR FILLER LAP
BEHIND FLANGE
DOOR CLOSED
OVERLAY PANEL
19 mm THICK
(NOMINAL)
MAIN FRAME
HINGE
L
PA
N
*6
m
m
m
13
EL
PA
NE
m
m
m
19
DOOR OPEN @ 130˚
L
PA
NE
m
m
m
25
32
PA
NE
L
PA
N
EL
STANDARD
FRAMED
FULL-LENGTH
HANDLE
m
APPROX
PROFILE OF
STAINLESS
STEEL DOOR
AND HANDLE
OPTIONAL
FRAMED EXTENDED
FULL-LENGTH HANDLE
*Approximate thickness of wrapped
stainless steel door.
25
OVERLAY PANEL APPLICATION – 90˚ DOOR OPENING (TOP VIEW)
The full-scale illustration
shows what considerations you need to make
for overlay panel applications and how they
may interact with
adjacent cabinets and
countertops.
OPENING
90˚ DOOR
(TOP VIEW)
NOMINAL OVERALL
WIDTH OF SUB-ZERO
SUB-ZERO UNIT
606 mm TO REAR
OF SUB-ZERO
MAIN FRAME
0 mm
6 mm
DOOR CLOSED
13 mm
19 mm
HINGE
25 mm
32 mm
38 mm
44 mm
51 mm
57 mm
63 mm
DOOR OPEN @ 90˚
70 mm
76 mm
83 mm
*6 mm PANEL
13 mm PANEL
19 mm PANEL
25 mm PANEL
32 mm PANEL
89 mm
OVERLAY PANEL
19 mm THICK (NOMINAL)
26
*Approximate thickness of wrapped
stainless steel door.
INTEGRATED REFRIGERATION
A L L R E F R I G E R AT O R | A L L F R E E Z E R
NEW
For generations, the Sub-Zero name has been
synonymous with built-in refrigeration. With the
Integrated line, we‘ve taken the idea a step
further—refrigerators and freezers you can hide
anywhere in the house, inside the furniture or
cabinetry of your choosing.
Created to blend invisibly into your home‘s
decor, the Integrated line lets you integrate
refrigeration into the kitchen, master suite, media
room or workout room. Available as tall units or
two-drawer base units, the Integrated line
expands the possibilities for the way you shape
your home.
Tall units are 2032 mm high and offered in two
different widths—686 mm and 914 mm. The 686
mm wide tall unit can be ordered as an all refrigerator, all freezer or combination refrigerator
(upper cabinet) and freezer (drawers). The 914
mm wide tall unit is offered as an all refrigerator
or combination unit. All of these models are 610
mm deep.
Base units are offered in the 686 mm width only.
They can be ordered as an all refrigerator, all
freezer or combination refrigerator (top drawer)
and freezer (bottom drawer). Base units are 876
mm high and 610 mm deep.
You just need to add whatever beautiful cabinetry you want to use. Optional classic stainless
steel panels with tubular handles are available as
sales accessories.
For information regarding specific Integrated
models, refer to the illustrations in this section.
686 mm
2032
mm
2032
mm
2032
mm
MODEL I700TR
MODEL I700TFI
MODEL I736TR
All Refrigerator
All Freezer
All Refrigerator
OVER-AND-UNDER
914 mm
686 mm
2032
mm
2032
mm
MODEL I700TCI
MODEL I736TCI
Refrigerator | Freezer
Refrigerator | Freezer
DRAWERS
686 mm
876
mm
Comprehensive installation
instructions are shipped with each
model. Refer to those instructions
in preparing and installing all
Sub-Zero products. The instructions
can also be found on our website,
subzero.com.
914 mm
686 mm
686 mm
2
876
mm
686 mm
2
876
mm
MODEL I700BR
MODEL I700BFI
MODEL I700BCI
All Refrigerator
All Freezer
Refrigerator | Freezer
With the installation of a harness kit,
tall models are Star-K compliant to meet
strict religious regulations in conjunction
with specific instructions found on
www.star-k.org. Drawer models are
Star-K certified from the factory with
no extra wiring harness required. For
details about the harness kit, contact
your Sub-Zero dealer.
27
MODEL I700TR
MODEL I736TR
A L L R E F R I G E R AT O R
A L L R E F R I G E R AT O R
S P E C I F I C AT I O N S
NEW
MODEL I700TFI
ALL FREEZER
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Overall Width
686 mm
Overall Width
914 mm
Overall Width
686 mm
Overall Height
2032 mm
Overall Height
2032 mm
Overall Height
2032 mm
Overall Depth
610 mm
Overall Depth
610 mm
Overall Depth
610 mm
Refrigerator Capacity
439 L
Refrigerator Capacity
595 L
Freezer Capacity
433 L
Min Height Required
2019 mm
Min Height Required
2019 mm
Min Height Required
2019 mm
Door Swing Clearance
648 mm
Door Swing Clearance
876 mm
Door Swing Clearance
648 mm
Specify Door Swing
LH or RH
Specify Door Swing
LH or RH
Specify Door Swing
LH or RH
Drawer Clearance
495 mm
Drawer Clearance
495 mm
Drawer Clearance
495 mm
Shipping Weight
163 kg
Shipping Weight
218 kg
Shipping Weight
163 kg
R E F R I G E R AT O R F E AT U R E S
R E F R I G E R AT O R F E AT U R E S
F R E E Z E R F E AT U R E S
Dual Refrigeration
Dual Refrigeration
1 Temperature Zone
2 Temperature Zones
2 Temperature Zones
3 Adjustable Glass Shelves
3 Adjustable Glass Shelves
3 Adjustable Glass Shelves
1 Stationary Shelf
1 Stationary Shelf
1 Stationary Shelf
2 Storage Drawers
2 Storage Drawers
2 Storage Drawers
1 Removable Drawer Divider
Removable Crisper Cover
Removable Crisper Cover
4 Adjustable Door Shelves
2 Removable Drawer Dividers
4 Removable Drawer Dividers
Automatic Defrost
Adjustable Deli Drawer
Adjustable Deli Drawer
Automatic Ice Maker
3 Adjustable Door Shelves
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Adjustable Dairy Compartment
Egg Container
Egg Container
PANEL OPTIONS
PANEL OPTIONS
PANEL OPTIONS
Integrated
Integrated
Integrated
Classic stainless steel finish
(includes handles)*
Classic stainless steel finish
(includes handles)*
Classic stainless steel finish
(includes handles)*
MODEL I700TR
MODEL I736TR
MODEL I700TFI
28
MODEL I700TCI
MODEL I736TCI
OVER-AND-UNDER
OVER-AND-UNDER
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Overall Width
686 mm
Overall Width
914 mm
Overall Height
2032 mm
Overall Height
2032 mm
Overall Depth
610 mm
Overall Depth
610 mm
Refrigerator Capacity
289 L
Refrigerator Capacity
383 L
Freezer Capacity
144 L
Freezer Capacity
195 L
Min Height Required
2019 mm
Min Height Required
2019 mm
Door Swing Clearance
648 mm
Door Swing Clearance
876 mm
Specify Door Swing
LH or RH
Specify Door Swing
LH or RH
Drawer Clearance
495 mm
Drawer Clearance
495 mm
Shipping Weight
163 kg
Shipping Weight
218 kg
R E F R I G E R AT O R ( D O O R )
R E F R I G E R AT O R ( D O O R )
Dual Refrigeration
Dual Refrigeration
3 Adjustable Glass Shelves
3 Adjustable Glass Shelves
1 Stationary Shelf
1 Stationary Shelf
Adjustable Deli Drawer
High-Humidity Crisper Drawer with Dividers
3 Adjustable Door Shelves
3 Adjustable Door Shelves
Adjustable Dairy Compartment
Adjustable Dairy Compartment
Egg Container
Egg Container
FREEZER (DRAWERS)
FREEZER (DRAWERS)
1 Removable Drawer Divider
1 Removable Drawer Divider
Automatic Defrost
Automatic Defrost
Automatic Ice Maker
Automatic Ice Maker
PANEL OPTIONS
PANEL OPTIONS
Integrated
Integrated
Classic stainless steel finish
(includes handles)*
Classic stainless steel finish
(includes handles)*
*Optional stainless steel panels and
handles are ordered and shipped as
sales accessories.
ACCESSORIES
Contact your Sub-Zero Dealer
Classic stainless steel front
panels
Tubular handles in classic
stainless steel
High-humidity crisper drawer and
shelf assembly*
Adjustable deli drawer and shelf
assembly*
Crisper cover with lid*
Dozen egg container with lid*
Dual installation heater kit
Harness kit for Star-K compliance
MODEL I700TCI
MODEL I736TCI
*Accessory is not available for
every model.
29
MODEL I700BR
MODEL I700BFI
MODEL I700BCI
R E F R I G E R AT O R D R A W E R S
FREEZER DRAWERS
R E F R I G E R AT O R | F R E E Z E R
DRAWERS
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Overall Width
686 mm
Overall Width
686 mm
Overall Width
686 mm
Overall Height
876 mm
Overall Height
876 mm
Overall Height
876 mm
Overall Depth
610 mm
Overall Depth
610 mm
Overall Depth
610 mm
Refrigerator Capacity
150 L
Freezer Capacity
144 L
Refrigerator Capacity
82 L
Min Height Required
864 mm
Min Height Required
864 mm
Freezer Capacity
59 L
Drawer Clearance
495 mm
Drawer Clearance
495 mm
Min Height Required
864 mm
Shipping Weight
86 kg
Shipping Weight
86 kg
Drawer Clearance
495 mm
Shipping Weight
86 kg
R E F R I G E R AT O R F E AT U R E S
F R E E Z E R F E AT U R E S
F E AT U R E S
1 Temperature Zone
1 Temperature Zone
2 Temperature Zones
2 Storage Drawers
2 Storage Drawers
2 Storage Drawers
Removable Crisper Cover
1 Removable Drawer Divider
Removable Crisper Cover
2 Removable Drawer Dividers
Automatic Defrost
1 Removable Drawer Divider
Automatic Ice Maker
Automatic Ice Maker
PANEL OPTIONS
PANEL OPTIONS
PANEL OPTIONS
Integrated
Integrated
Integrated
Classic stainless steel finish
(includes handles)*
Classic stainless steel finish
(includes handles)*
Classic stainless steel finish
(includes handles)*
MODEL I700BR
MODEL I700BFI
MODEL I700BCI
ACCESSORIES
Contact your Sub-Zero Dealer
*Optional stainless steel panels and
handles are ordered and shipped as
sales accessories.
Front panels in classic stainless
steel
Tubular handles in classic stainless
steel
Crisper cover with lid*
Dozen egg container with lid*
Dual installation heater kit
*Accessory is not available for
every model.
30
INTEGRATED FEATURES
All Integrated models accept wood or stainless
steel panels. The optional stainless steel panels
and handles are available in classic stainless
steel at the 2032 mm and 2134 mm height.
Stainless steel panels are ordered and shipped
as sales accessories.
Functional Design. These models can be placed
anywhere in the home. Think about “point-ofuse refrigeration” when planning where to place
your units.
Integrated Design. All Sub-Zero models are 610
mm deep. Tall Integrated units are 2032 mm high
and are offered in two different widths—686 mm
and 914 mm. All base units are 686 mm wide
and 876 mm high.
Microprocessor. The “brains” of the Integrated
units, this computer allows the best in temperature control, efficiency and food preservation.
Temperature Zones. On tall refrigerator and
combination units, you have the flexibility of
having two temperatures within the same unit.
Automatic Defrost. Depending on usage and
exact climate, the Integrated unit will adapt to
the unique situation and adjust accordingly to
offer greater efficiency. Integrated freezer and
combination units have an automatic defrost
system.
Kickplate. The adjustable solid kickplate meets
standards of the American Institute of Architects. The toe kick area for a solid, decorative
kickplate is 102 mm high by 76 mm deep. You
can show a 254 mm toe kick, but you cannot
cover the louvers of the kickplate. If you choose,
the kickplate can be painted.
Front Venting. All models have the mechanical
equipment in an area below the lower drawer.
The lower drawer panel can extend to cover
these louvers, but a removable decorative kickplate cannot cover the fins.
Lighting. Flat to the ceiling, superior lighting
provides white, efficient light in cabinet and
drawer units.
Door / Drawer Alarm. When activated, if your
door or drawer is accidentally left open for more
than 30 seconds, an audible alarm will sound.
Spill-Proof Shelves. The cabinet section of the
tall units features adjustable spill-proof one-piece
glass shelves that are easily removed for
cleaning.
Dairy Shelf. This magnetically sealed compartment is fully adjustable on the tall refrigerator and
combination units.
Crisper Cover. On the tall and base refrigerator
units and the base combination unit, a removable
crisper cover is offered for one of the drawer
sections.
Deli Drawer. Smaller items are not lost in this
handy feature of the Models I700TR and I700TCI.
Available as a sales accessory for Model I736TCI.
Crisper—Model I736TCI. Model I736TCI is
equipped with a sealed crisper. It is large and
deep, with smooth sides for easy cleaning. The
space features removable dividers.
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer.
Egg Container. You can store a dozen eggs in
this removable egg container with lid in the tall
refrigerator and tall combination units.
Ice Maker. An automatic ice maker, providing
crescent-shaped ice, is available as an option on
the tall and base freezers as well as the tall and
base combination units. This optional equipment
must be factory installed.
Door Swing. You can choose left or right door
swing on the tall units. This option must be
ordered when requesting the unit. You cannot
reverse the door in the field.
Dual-Action Hinge. An exclusive dual-action
hinge is featured on all of the tall units, allowing
for a fully integrated look.
Door Stop. On all of the tall units, a 90˚ door stop
is built in to the hinge. Normal door swing is 105˚.
Temperature Zones. With the microprocessor in
the Integrated models, you have the capability of
setting different optimum temperatures.
T E M P E R AT U R E Z O N E S
Model I700BR – One zone,
1˚C to 7˚C
Models I700TR and I736TR –
Two zones, 1˚C to 7˚C
Models I700BFI and I700TFI –
One zone, -21˚C to -15˚C
Model I700TFI – One zone,
-21˚C to -15˚C
Model I700BCI – Two zones,
1˚C to 7˚C top drawer;
-21˚C to -15˚C bottom drawer
Models I700TCI and I736TCI –
Two zones, 1˚C to 7˚C cabinet;
-21˚C to -15˚C drawers
31
PLANNING INFORMATION
Before moving the Integrated unit into place, be
sure that the finished opening dimensions, electrical and plumbing locations and minimum door
and drawer clearances are accurate. Refer to the
Installation Specifications illustration for your
model on the following pages. Be sure your
installer has this information before finishing
work is completed.
I N S TA L L AT I O N
Refer to the
installation instructions shipped with
each Sub-Zero
product for detailed
specifications.
Integrated models without an automatic ice
maker will not require the plumbing connections
shown in the illustrations.
The height of the tall unit is set at 2032 mm.
You can allow the top of the door panel to
exceed this dimension with caution. If you are
working with 2134 mm or 2438 mm neighboring
panels, you can utilize door panels to match this
height. Other critical dimensions regarding the
door swing, drawer openings and toe kick clearance are noted in the Overall Dimensions illustrations on the following pages. Also refer to the
full-scale illustrations at the end of this section
for specifics on door openings and other specifications.
IMPORTANT NOTE: The anti-tip bracket must be
installed to prevent the unit from tipping
forward.
ELECTRICAL REQUIREMENTS
International models from the factory designed
without a transformer require a 220/240 V AC,
50/60 Hz electrical supply, fused at the correct
rating for the unit. If required by local or national
codes, the power cord can be easily replaced
using the power inlet device.
International models using a factory installed
transformer require a 220/240 V AC, 50/60 Hz
electrical supply, fused at the correct rating for
the unit. These models will come equipped with
Schuko power cords. The power cord may need
to be replaced depending on local and national
codes. The USA power cord that is supplied
with the product must be disconnected with the
appropriate transformer output to be connected
in its place.
IMPORTANT NOTE: The electrical outlet must
be grounded. The outlet must be flush with the
back wall. Refer to the Installation Specifications
illustration for your model for exact placement.
IMPORTANT NOTE: A ground fault circuit
interrupter (GFCI) is not recommended and may
cause interruption of operation.
32
Do not use an extension cord or 2-prong
adapter. Electrical ground is required.
Do not under any circumstances remove
the power supply cord ground prong.
PLUMBING CONSIDERATIONS
For models with an automatic ice maker, rough
in the water supply line. Connect a 6.35 mm OD
copper line to the house supply, being sure to
use an easily accessible shut-off valve between
the supply and the unit. This shut-off valve
should not be installed behind the unit.
Do not use self-piercing valves. A saddle valve
kit (4200880) is available from your Sub-Zero
dealer. An in-line filter is required when water
conditions have a high sediment content. The ice
maker operates on constant water pressure
between 1.4 bar and 6.9 bar.
IMPORTANT NOTE: In some cases, a reverse
osmosis water filter system may not be able to
maintain the minimum pressure consistently.
The Installation Specifications illustration for
your model on the following pages shows the
precise placement of the water line. When
routing the water through the side walls, you
must place the water line within 13 mm of the
floor and as close as possible to the back wall.
The line must be routed around the anti-tip
bracket so it clears the bracket and the leveling
feet of the unit as shown in the top view of the
illustration. Regardless of the routing, allow for
686 mm of excess copper tubing to remain
outside the wall or floor for easy connection to
the unit.
IMPORTANT NOTE: Do not route water supply
line in front of the compressor tray. The tray
must be slid forward for service.
OVERALL DIMENSIONS
Models I700TR, I700TFI and I700TCI
686 mm
610 mm
TOP OF
ROUGH
OPENING
(UNIT DIMENSION)
356 mm
(UNIT DIMENSION)
A L L R E F R I G E R AT O R
ALL FREEZER
21
mm
610 mm
DOOR
MOUNTING
DETAIL
DOOR/ DRAWER
CLOSED
Model I700TR
All Refrigerator
DOOR/ DRAWER
CLOSED
Model I700TFI
All Freezer
with Ice Maker
2032
mm*
90˚
648
mm*
1995
mm*
10 mm
495
mm*
105˚
OVER-AND-UNDER
Refrigerator | Freezer
657 mm
337
13 mm
mm
DRAWER
MOUNTING DETAIL
117 mm*
90˚ DOOR OPENING
Model I700TCI
with Ice Maker
TOP VIEW
876
mm*
260
mm
MAXIMUM DOOR OPENING
*DOOR/DRAWER PANEL THICKNESS NOT INCLUDED – DIMENSION WILL VARY WITH INSTALLATION
518 mm
248
mm
102
mm
FRONT VIEW
SIDE VIEW
*13 mm +_ ADJUSTMENT IN LEVELING LEGS
I N S TA L L AT I O N
S P E C I F I C AT I O N S
TOP VIEW
Models I700TR, I700TFI and I700TCI
Models without an ice maker will not
require the water line connection.
38
mm
152
mm
ANTI-TIP
BRACKET*
635 mm
343 mm
394 mm
343 mm
229
mm
ANTI-TIP
BRACKET
686 mm
686 mm
WATER LINE
SIDE ENTRY
LOCATIONS
WATER LINE
BOTTOM ENTRY
LOCATION
*PLACEMENT OF THE
ANTI-TIP BRACKET
SHOULD BE 610 mm
FROM THE FRONT OF THE
UNIT WITHOUT PANELS
TO THE BACK OF THE
ANTI-TIP BRACKET.
MODEL I700TR
MODEL I700TFI
MODEL I700TCI
TOP VIEW
38 mm
686 mm
38 mm
635 mm
LOCATE WATER LINE
(REAR ENTRY) WITHIN
SHADED AREA
114
mm
Width
686 mm
Height
2032 mm
Depth
610 mm
Finished Opening
Width
686 mm
Height
2032 mm
Depth
635 mm*
*The depth of the unit
is 610 mm from the
front of the unit to its
back. Your design may
necessitate moving the
unit back or cabinets
forward to achieve a
flush fit. This will
require a minimum
rough opening depth
of 635 mm.
LOCATE ELECTRICAL WITHIN
SHADED AREA – ORIENT GROUND
PRONG TO RIGHT AS SHOWN
ANTI-TIP
BRACKET
Overall Dimensions
2032 mm
76
mm
6
mm
330 mm
229 mm
64 mm
19
mm
394 mm
NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO
PREVENT UNIT FROM TIPPING FORWARD
ANTI-TIP
BRACKET
FRONT VIEW
SIDE VIEW
WATER LINE
SIDE ENTRY
LOCATION
33
OVERALL DIMENSIONS
Models I736TR and I736TCI
914 mm
610 mm
TOP OF
ROUGH
OPENING
(UNIT DIMENSION)
356 mm
(UNIT DIMENSION)
A L L R E F R I G E R AT O R
33
mm
Model I736TR
All Refrigerator
610 mm
DOOR MOUNTING
DETAIL
DOOR/DRAWER
CLOSED
DOOR/DRAWER
CLOSED
2032
mm*
OVER-AND-UNDER
Refrigerator | Freezer
90˚
Model I736TCI
with Ice Maker
1976
mm*
10 mm
495
876 mm*
mm*
105˚
886 mm
337
13 mm
mm
DRAWER MOUNTING
DETAIL
90˚ DOOR OPENING
876
mm*
260
mm
MAXIMUM DOOR OPENING
TOP VIEW
178
mm*
*DOOR/DRAWER PANEL THICKNESS NOT INCLUDED – DIMENSION WILL VARY WITH INSTALLATION
518
mm
248
mm
102
mm
FRONT VIEW
SIDE VIEW
*13 mm +_ ADJUSTMENT IN LEVELING LEGS
MODEL I736TR
MODEL I736TCI
TOP VIEW
I N S TA L L AT I O N
S P E C I F I C AT I O N S
Models I736TR and I736TCI
38
mm
Overall Dimensions
Width
914 mm
Height
2032 mm
Depth
610 mm
Models without an ice maker
will not require the water line
connection.
TOP VIEW
152
mm
ANTI-TIP
BRACKET*
635 mm
457 mm
ANTI-TIP
BRACKET
457 mm
343 mm
508 mm
686 mm
686 mm
WATER LINE
SIDE ENTRY
LOCATIONS
WATER LINE
BOTTOM ENTRY
LOCATION
Finished Opening
Width
914 mm
Height
2032 mm
Depth
*PLACEMENT OF THE
ANTI-TIP BRACKET
SHOULD BE 610 mm
FROM THE FRONT OF THE
UNIT WITHOUT PANELS
TO THE BACK OF THE
ANTI-TIP BRACKET.
635 mm*
*The depth of the unit
is 610 mm from the
front of the unit to its
back. Your design may
necessitate moving the
unit back or cabinets
forward to achieve a
flush fit. This will
require a minimum
rough opening depth
of 635 mm.
38 mm
914 mm
38 mm
635 mm
LOCATE ELECTRICAL WITHIN
SHADED AREA – ORIENT GROUND
PRONG TO RIGHT AS SHOWN
LOCATE WATER LINE
(REAR ENTRY) WITHIN
SHADED AREA
ANTI-TIP
BRACKET
2032 mm
114
mm
76
mm
6
mm
445 mm
343 mm
64 mm
19
mm
508 mm
NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO
PREVENT UNIT FROM TIPPING FORWARD
34
ANTI-TIP
BRACKET
FRONT VIEW
SIDE VIEW
WATER LINE
SIDE ENTRY
LOCATION
OVERALL DIMENSIONS
Models I700BR, I700BFI and I700BCI
10 mm
686 mm
610 mm
(UNIT DIMENSION)
(UNIT DIMENSION)
DRAWERS
337
13 mm
mm
DRAWER
MOUNTING DETAIL
Model I700BR
All Refrigerator
610 mm
876
mm*
260
mm
518
mm
Model I700BFI
All Freezer
with Ice Maker
DRAWER CLOSED
Model I700BCI
Refrigerator | Freezer
with Ice Maker
248 mm
495 mm*
102
mm
FRONT VIEW
SIDE VIEW
*13 mm +_ ADJUSTMENT IN LEVELING LEGS
657 mm
TOP VIEW
*DRAWER PANEL THICKNESS NOT INCLUDED
TOP VIEW
I N S TA L L AT I O N
S P E C I F I C AT I O N S
Models I700BR, I700BFI and I700BCI
Models without an ice maker
will not require the water line
connection.
38
mm
152
mm
ANTI-TIP
BRACKET*
635 mm
343 mm
394 mm
MODEL I700BR
MODEL I700BFI
MODEL I700BCI
TOP VIEW
343 mm
229
mm
ANTI-TIP
BRACKET
686 mm
Overall Dimensions
686 mm
WATER LINE
SIDE ENTRY
LOCATIONS
WATER LINE
BOTTOM ENTRY
LOCATION
Width
686 mm
Height
876 mm
Depth
610 mm
Finished Opening
*PLACEMENT OF THE
ANTI-TIP BRACKET
SHOULD BE 610 mm
FROM THE FRONT OF THE
UNIT WITHOUT PANELS
TO THE BACK OF THE
ANTI-TIP BRACKET.
38 mm
686 mm
38 mm
ANTI-TIP
BRACKET
FRONT VIEW
686 mm
Height
876 mm
Depth
635 mm*
635 mm
876 mm
NOTE: ANTI-TIP BRACKET MUST BE INSTALLED TO
PREVENT UNIT FROM TIPPING FORWARD
Width
SIDE VIEW
WATER LINE
SIDE ENTRY
LOCATION
*The depth of the unit
is 610 mm from the
front of the unit to its
back. Your design may
necessitate moving the
unit back or cabinets
forward to achieve a
flush fit. This will
require a minimum
rough opening depth of
635 mm.
LOCATE ELECTRICAL WITHIN
SHADED AREA – ORIENT GROUND
PRONG TO RIGHT AS SHOWN
ANTI-TIP
BRACKET
I N S TA L L AT I O N
LOCATE WATER LINE
(REAR ENTRY) WITHIN
SHADED AREA
114
mm
76
mm
6
mm
330 mm
64 mm
229 mm
19
mm
Refer to the
installation instructions shipped with
each Sub-Zero
product for detailed
specifications.
394 mm
35
PANEL
REQUIREMENTS
Door and drawer
panels must be a
minimum of 16 mm
thick.
The door panel
cannot exceed 18 kg
and each drawer
panel must not
exceed 5 kg for 686
mm wide units. For
914 mm wide units,
the door panel
weight limit is 24 kg
and 7 kg for each
drawer panel.
CABINETRY APPLICATIONS
FRAMED CABINETRY
Integrated refrigeration is compatible with virtually any style and look of cabinetry. The models
can be used with framed as well as frameless
cabinets. Because of the precise application and
the look you may want to achieve, there are
important questions you need to answer before
ordering panels for the doors/drawers. As you
look at styles of cabinets, keep some important
facts in mind:
Framed cabinetry applications present you with
different questions to address. The illustrations
below show common applications of framed
cabinetry. These are not meant to be the only
alternatives, but are suggestions from designers
around the country. Also refer to the full-scale
illustrations at the end of this section for
specifics on door openings.
NOTE: In the illustrations below, the first width
dimension shown is for 686 mm wide units and
the second dimension is for 914 mm wide units.
IMPORTANT NOTE: The depth of each Integrated model is 610 mm from the front of the
unit to its back. You must allow for the thickness of the panel you are applying when
planning for the finished rough opening depth if
you want the front panel to be flush with
surrounding cabinetry. You must move the unit
back into drywall or bring the cabinets forward
to achieve a flush fit.
The height of the door panel can grow beyond
1153 mm and exceed the 2032 mm overall
height as long as you stay below the recommended door panel weight limit.
The toe kick clearance can vary with the height
of the lower drawer panel; the maximum panel
height is 424 mm. You must keep a minimum
space of 102 mm clear below the bottom edge
of the lower drawer panel so the unit can be
properly vented.
We recommend using D-style handles. For the
cabinet door, handles must be located near the
edge of the panel opposite the hinge, centered
top to bottom. Locate handles in the top center
area of the drawer panels.
IMPORTANT NOTE: The inside edges of the
rough opening, as well as the sides and a
portion of the backside of the decorative panels
will need to be finished, as they will be exposed
when the doors are open.
SUB-ZERO
UNIT
CABINET
FRAME
CABINET
DOOR
10 mm
REVEAL
DOOR PANEL
686 mm
OR
Traditional frame – full overlay
(top view)
36
610 mm
TO WALL
914 mm
SUB-ZERO
UNIT
CABINET
FRAME
CABINET
DOOR
610 mm
610 mm
SUB-ZERO
UNIT
TO WALL
TO WALL
CABINET
FRAME
10 mm
REVEAL
DOOR PANEL
686 mm
OR
914 mm
Traditional frame – standard overlay
(top view)
CABINET
DOOR
10 mm
REVEAL
DOOR PANEL
686 mm
OR
914 mm
Traditional frame – 10 mm offset
(top view)
FRAMED CABINETRY –
BEADED INSET APPLICATION
The illustration below shows a 686 mm wide
Integrated base or tall unit installed within a
framed cabinetry, beaded inset application.
Review, giving particular attention to the overall
panel specifications. Also refer to the full-scale
illustrations at the end of this section for
specifics on door openings.
686 mm
WIDE MODELS
Installation of a
686 mm wide
Integrated base or
tall unit within
framed cabinetry.
610 mm
SUB-ZERO
UNIT
CABINET DOOR
TO WALL
DOOR PANEL
A
*Dimensions may vary.
A
TOP VIEW
A) ALL REVEALS ARE 3 mm
B) DRAWER RAILS ARE ATTACHED TO DRAWER FRONTS
C) BOTTOM RAIL MUST BE REMOVABLE
686 mm
*DIMENSIONS MAY VARY
679 mm
PANEL WIDTH
38
mm
Dimensions are based
on a 3 mm reveal. A
reveal of up to 6 mm
is possible, but panel
dimensions need to be
adjusted accordingly.
I N S TA L L AT I O N
To install integrated
panels, see the
detailed procedures
outlined in the
Sub-Zero Integrated
Installation Guide.
2624
mm
1216
mm
SHADED AREA
INDICATES STATIONARY
STYLES AND RAILS
2032
mm*
A
B
345 mm
A
B
876
mm*
383 mm
38
mm
A
C
102 mm*
686 mm
38 mm
38 mm
FRONT VIEW
102 mm
610 mm
SIDE VIEW
37
FRAMED CABINETRY –
BEADED INSET APPLICATION
The illustration below shows 914 mm wide Integrated tall unit installed within a framed cabinetry, beaded inset application. Review, giving
particular attention to the overall panel specifications. Also refer to the full-scale illustrations at
the end of this section for specifics on door
openings.
914 mm
WIDE MODELS
Installation of a
914 mm wide
Integrated tall unit
within framed
cabinetry.
610 mm
CABINET DOOR
DOOR PANEL
*Dimensions may vary.
Dimensions are based
on a 3 mm reveal. A
reveal of up to 6 mm
is possible, but panel
dimensions need to be
adjusted accordingly.
TO WALL
SUB-ZERO
UNIT
A
TOP VIEW
A
A) ALL REVEALS ARE 3 mm
B) DRAWER RAILS ARE ATTACHED TO DRAWER FRONTS
C) BOTTOM RAIL MUST BE REMOVABLE
914 mm
*DIMENSIONS MAY VARY
908 mm
PANEL WIDTH
38
mm
I N S TA L L AT I O N
To install integrated
panels, see the
detailed procedures
outlined in the
Sub-Zero Integrated
Installation Guide.
2624
mm
1216
mm
SHADED AREA
INDICATES STATIONARY
STYLES AND RAILS
2032
mm*
A
B
345 mm
A
B
876
mm*
383 mm
38
mm
A
C
102 mm*
914 mm
38 mm
38 mm
FRONT VIEW
38
102 mm
610 mm
SIDE VIEW
679 mm*
FRAMELESS CABINETRY
610 mm
PANEL WIDTH
The illustrations show hypothetical installations of Integrated
base or tall units within frameless
cabinetry. Review, giving particular attention to the overall panel
specifications. Also refer to the
full-scale illustrations at the end
of this section for specifics on
door openings.
A
1153 mm
2032
mm*
686 mm
WIDE MODELS
2029
mm*
Installation of a
686 mm wide
Integrated base or
tall unit within
frameless cabinetry.
A
345 mm
A
*Dimensions may vary.
876
mm*
Dimensions are based
on a 3 mm reveal. A
reveal of up to 6 mm
is possible, but panel
dimensions need to be
adjusted accordingly.
424 mm*
102 mm*
686 mm
SIDE VIEW
TOE KICK
FINISHED OPENING
A) ALL REVEALS ARE 3 mm
*DIMENSIONS MAY VARY
914 mm
WIDE MODELS
908 mm*
610 mm
PANEL WIDTH
Installation of a
914 mm wide
Integrated tall unit
within frameless
cabinetry.
A
*Dimensions may vary.
Dimensions are based
on a 3 mm reveal. A
reveal of up to 6 mm
is possible, but panel
dimensions need to be
adjusted accordingly.
1153 mm
2032
mm*
2029
mm*
A
345 mm
A
876
mm*
424 mm*
102 mm*
914 mm
TOE KICK
SIDE VIEW
FINISHED OPENING
A) ALL REVEALS ARE 3 mm
39
*DIMENSIONS MAY VARY
PANEL CONSIDERATIONS
The illustrations below provide panel width
dimensions for installation of a single tall unit,
686 mm and 914 mm wide models.
Illustrations on the following page provide panel
width dimensions for installing two tall units
side by side, 686 mm wide models and 914 mm
wide models.
IMPORTANT NOTE: The depth of each
Integrated model is 610 mm from the front of
the unit to its back. You must allow for the
thickness of the panel you are applying when
planning for the finished rough opening depth if
you want the front panel to be flush with
surrounding cabinetry. You may have to move
the unit back into drywall or bring the cabinets
forward to achieve a flush fit.
I N S TA L L AT I O N
To install integrated
panels, see the
detailed procedures
outlined in the
Sub-Zero Integrated
Installation Guide.
686 mm
WIDE MODELS
Panel width dimensions for installation
of a 686 mm wide
tall unit.
Dimensions are based
on a 3 mm reveal. A
reveal of up to 6 mm
is possible, but panel
dimensions need to be
adjusted accordingly.
3 mm* min
686 mm
3 mm* min
679 mm
REVEAL
REVEAL
19 mm PANEL
657 mm
635 mm
CABINETRY
OR SIDE
PANEL
610 mm
APPLIANCE
DOOR WIDTH
TO BACK
OF UNIT
635 mm
CABINETRY
OR SIDE
PANEL
SUB-ZERO
UNIT
*SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL
914 mm
WIDE MODELS
Panel width dimensions for installation
of a 914 mm wide
tall unit.
Dimensions are based
on a 3 mm reveal. A
reveal of up to 6 mm
is possible, but panel
dimensions need to be
adjusted accordingly.
3 mm* min
914 mm
3 mm* min
908 mm
REVEAL
REVEAL
19 mm PANEL
886 mm
635 mm
CABINETRY
OR SIDE
PANEL
610 mm
APPLIANCE
DOOR WIDTH
TO BACK
OF UNIT
635 mm
CABINETRY
OR SIDE
PANEL
SUB-ZERO
UNIT
*SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL
40
As the reveal between cabinets and the
Integrated unit decreases, the potential
exists for severe finger pinching or crushing
if a hand or fingers are placed in the
opening when the door is closing.
When 19 mm or thicker panels are used
and a reveal less than 6 mm is maintained,
the door panels may cause damage to the
Sub-Zero unit when the door is open at the
maximum 105˚ stop. You should use the
built-in 90˚ stop to prevent damage.
PANEL
REQUIREMENTS
686 mm
WIDE MODELS
1372 mm
3 mm* min
681 mm
681 mm
3 mm* min
REVEAL
3 mm* min
REVEAL
REVEAL
19 mm PANEL
19 mm PANEL
635 mm
635 mm
CABINETRY
OR SIDE
PANEL
610
mm
DOOR
DOOR
SUB-ZERO
UNIT
SUB-ZERO
UNIT
TO BACK
OF UNIT
CABINETRY
OR SIDE
PANEL
Panel width dimensions for installation
of two 686 mm wide
tall units side by
side.
Dimensions are based
on a 3 mm reveal. A
reveal of up to 6 mm
is possible, but panel
dimensions need to be
adjusted accordingly.
Door and drawer
panels must be a
minimum of 16 mm
thick.
The door panel
cannot exceed 18 kg
and each drawer
panel must not
exceed 5 kg for 686
mm wide units. For
914 mm wide units,
the door panel
weight limit is 24 kg
and 7 kg for each
drawer panel.
*SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL
914 mm
WIDE MODELS
1829 mm
3 mm* min
910 mm
910 mm
3 mm* min
REVEAL
3 mm* min
REVEAL
REVEAL
19 mm PANEL
19 mm PANEL
635 mm
635 mm
CABINETRY
OR SIDE
PANEL
CABINETRY
OR SIDE
PANEL
610 mm
DOOR
DOOR
SUB-ZERO
UNIT
SUB-ZERO
UNIT
TO BACK
OF UNIT
Panel width dimensions for installation
of two 914 mm wide
tall units side by
side.
Dimensions are based
on a 3 mm reveal. A
reveal of up to 6 mm
is possible, but panel
dimensions need to be
adjusted accordingly.
*SUBTRACT PANEL WIDTH FROM CABINETRY OPENING TO DETERMINE ACTUAL WIDTH OF REVEAL
41
INSTALLATION OPTIONS
The illustrations show some typical installations
and their dimension considerations. The depth
dimension in the illustrations may vary depending on cabinet styles, treatment of countertops
or other design options.
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer.
IMPORTANT NOTE: The depth of each
Integrated model is 610 mm from the front of
the unit to its back. Your design may necessitate
moving the unit back or cabinets forward to
achieve a flush fit. This will require a minimum
rough opening depth of 635 mm. Refer to the
illustrations.
CABINETS
635
mm
686 mm
914 mm
TOP VIEW
Installation without side panels
NOTE: In the Installation Options illustrations,
the first width dimension shown is for 686 mm
wide units and the second dimension is for 914
mm wide units.
CABINETS
635
mm
DUAL INSTALLATIONS
If two or more Integrated models are installed
side by side where there is 51 mm or less of
space between the units, a heater kit is recommended—TTDUAL for two tall units installed side
by side and BBDUAL for two base units or a
base unit and a tall unit installed side by side.
These optional components are available through
your Sub-Zero dealer.
OR
686 mm
OR
914 mm
MINIMUM 16 mm SIDE PANELS
Installation with side panels
CABINETS
635
mm
1372 mm
OR
1829 mm
TOP VIEW
Installation of two units side by side
CABINETS
635
mm
686 mm
OR
914 mm
MINIMUM 16 mm SIDE PANELS
Installation at end of run
42
DOOR PANEL HEIGHT
TOE KICK CLEARANCE
The height of the door panel can grow beyond
1153 mm and exceed the 2032 mm overall
height, as long as you stay below the recommended door panel weight limit.
The toe kick clearance can vary with the height
of the lower drawer panel; the maximum panel
height is 424 mm.
The top illustration shows how the panel may
grow and what you need to consider doing to
finish the area in back of the door panel.
IMPORTANT NOTE: The valance you use to
finish the area behind the door panel must stay
behind the front plane of the finished molding.
IMPORTANT NOTE: You must keep a minimum
space of 102 mm clear below the bottom edge
of the lower drawer panel so the unit can be
properly vented. In addition, any decorative base
molding must be removable for possible servicing and cleaning of the condenser.
The bottom illustration shows the area below
the lower drawer where the operating mechanical equipment of the Integrated unit is housed.
UPPER VALANCE
Tall Models
635 mm
TO WALL
38 mm
The depth of each
Integrated model is
610 mm from the
front of the unit to its
back. Your design
may necessitate
moving the unit back
or cabinets forward to
achieve a flush fit.
This will require a
minimum rough
opening depth of
635 mm.
DECORATIVE VALANCE
CANNOT EXTEND BEYOND
THE FRONT OF THIS PLANE
DECORATIVE VALANCE
3 mm
PANEL
REQUIREMENTS
Door and drawer
panels must be a
minimum of 16 mm
thick.
The door panel
cannot exceed 18 kg
and each drawer
panel must not
exceed 5 kg for 686
mm wide units. For
914 mm wide units,
the door panel
weight limit is 24 kg
and 7 kg for each
drawer panel.
REMOVABLE MOLDING
BY SUB-ZERO
1153 mm
TO
BOTTOM
OF
DOOR
PANEL
TOP HINGE
2032
mm*
TO
FLOOR
*FINISHED HEIGHT OF 2032 mm IS TO TOP OF SUB-ZERO MOLDING
K I C K P L AT E A R E A
Base and Tall Models
268
mm
PANEL
13
mm
424 mm
PANEL
246 mm
254 mm
OPTIONAL
BASE MOLDING MUST
BE REMOVABLE
102 mm
635 mm
TO WALL
67 mm
TO
102 mm
FLOOR
43
FRAMED CABINETRY
IMPORTANT NOTE: The depth of each
Integrated model is 610 mm from the
front of the unit to its back. Your
design may necessitate moving the
unit back or cabinets forward to
achieve a flush fit.
DOOR CLOSED
SUB-ZERO
DOOR
105˚ MAXIMUM
DOOR OPENING
Full-scale (top view)
1/4 scale (top view)
610 mm
TO BACK
OF UNIT
LINE OF INTERFERENCE*
LINE OF INTERFERENCE*
AT MAXIMUM DOOR OPENING
MOUNTING BRACKET SCREW
3 mm min.
REVEAL
PANEL
19 mm
657 mm DOOR WIDTH FOR 686 mm MODELS
886 mm DOOR WIDTH FOR 914 mm MODELS
SUB-ZERO DOOR
610 mm
TO BACK
OF UNIT
LINE OF INTERFERENCE*
SIDE MOLDING AND
INSTALLATION HARDWARE
PROVIDED BY SUB-ZERO
FLUSH
FURNITURE
FINISH
44
*If the panel is thicker than 19 mm, it is
recommended that you utilize the built-in
90˚ door stop to prevent damage to the
panel and face frame.
FRAMELESS CABINETRY
IMPORTANT NOTE: The depth of each
Integrated model is 610 mm from the
front of the unit to its back. Your
design may necessitate moving the
unit back or cabinets forward to
achieve a flush fit.
SUB-ZERO DOOR
19 mm DOOR PANEL
COUNTERTOP
SIDE PANEL
105˚ MAXIMUM
DOOR OPENING
DOOR CLOSED
1/4 scale (top view)
Full-scale (top view)
Adjacent side panel and
countertop application.
610 mm
TO
WALL
LINE OF INTERFERENCE*
LINE OF INTERFERENCE*
AT MAXIMUM DOOR OPENING
3 mm min.
REVEAL
MOUNTING BRACKET SCREW
19 mm
PANEL
657 mm DOOR WIDTH FOR 686 mm MODELS
886 mm DOOR WIDTH FOR 914 mm MODELS
SUB-ZERO DOOR
610 mm
TO BACK
OF UNIT
LINE OF INTERFERENCE*
SIDE MOLDING AND
INSTALLATION HARDWARE
PROVIDED BY SUB-ZERO
*If the panel is thicker than 19 mm, it is
recommended that you utilize the built-in
90˚ door stop to prevent damage to the
panel and face frame.
45
WINE STORAGE
UNDERCOUNTER
606 mm
864
mm
616 mm
868
mm
MODEL I424
MODEL I424FS
Built-In
Free-Standing
ALL WINE STORAGE
Sub-Zero‘s innovative addition to its complete
line of residential refrigeration is wine storage
equipment—the ultimate in beauty, engineering,
and attention to detail. From the exterior and the
smooth lines of the free-standing Model I424FS
classic stainless steel to the ability to use wood
on the Built-In and Integrated models, each unit
is beautiful.
With the exception of the free-standing Model
I424FS, each model will have the capability of
having wood panels applied to the doors. With
the Model I427R, you can also apply the wood
to the drawers.
762 mm
686 mm
The free-standing Model I424FS does not require
any panels or surrounding cabinetry; it comes
with classic stainless steel exterior.
All models will be shipped with glass doors as
standard equipment. The glass doors allow one
to see the wine that is being stored.
2134
mm
2032
mm
MODEL I427
MODEL I430
Integrated
Built-In
W I N E S T O R A G E | R E F R I G E R AT O R
686 mm
Standard grille assemblies for the Model I430
will be provided in 25 mm increments from 254
mm to 381 mm. The standard height will be 279
mm. The overlay model will have the panel grille,
which accepts decorative panel inserts.
For information regarding specific Wine Storage
models, refer to the illustrations in this section.
2032
mm
MODEL I427R
With the installation of a harness
kit, Wine Storage models are
Star-K compliant to meet strict
religious regulations in conjunction
with specific instructions found on
www.star-k.org. For details about
the harness kit, contact your
Sub-Zero dealer.
Integrated
The illustrations represent the full line of
Wine Storage models. The Model I424FS
free-standing unit comes with a classic
stainless steel exterior.
Comprehensive installation instructions are
shipped with each model. Refer to those
instructions in preparing and installing all
Sub-Zero products. The instructions can
also be found on our website,
subzero.com.
46
Stainless steel models will be shipped with
tubular stainless steel handles, while the overlay
models will come with no handle hardware.
Accessory overlay handles are available. Optional
stainless steel panels and handles for Models
I427 and I427R are offered in the classic stainless steel finish and are ordered and shipped as
sales accessories.
FEATURES AND OPTIONS
When looking for wine storage, you no longer
have to think only about an undercounter application. Sub-Zero offers you complete flexibility
from the perspective of design applications and
storage capabilities.
Model I424 comes in the overlay and stainless
steel door panel configurations. Model I424FS
(free-standing) is identical to the Model I424 but
with classic stainless steel exterior and is
designed to be attractive in a stand-alone
setting.
Models I427 and I427R are offered as integrated
or stainless steel. Optional classic stainless steel
panels and handles are offered at the 2032 mm
and 2134 mm height. Stainless steel panels are
available as sales accessories.
Model I430 comes in overlay and stainless steel.
Stainless steel Model I430 comes with a
standard 279 mm heavy-duty grille, 25 mm
diameter stainless steel handles and a stainless
steel kickplate.
Built-In Look. Sub-Zero offers you a host of
design alternatives to choose from when selecting the look you want. Wood or stainless steel,
overlay or integrated.
Dual Zone System. All Wine Storage models
allow you to have precise temperature control
within one degree of your pre-set temperature in
each of the two wine compartments.
Dual Refrigeration System. In a similar fashion
to our Built-In, each Wine Storage model has
dual refrigeration so your client will have
specific, individual temperature control of the
two wine compartments.
Electronic Controls. Microprocessor offers
touch pad controls that are easy to understand
and that set the temperatures accurately.
Display Shelf. This beautiful shelf offers your
clients the opportunity to display those prize
bottles or magnums of wine in their collection. It
is illuminated with discreet lighting mounted in
the control panel. (Not available with Models
I424 and I424FS.)
Storage Shelves. The sturdy, rustproof wire
shelves can easily accommodate standard 750
ml bottles, half bottles, as well as magnums. All
the shelves are finished off with a natural cherry
wood facing. In addition, all shelves will enable
you to be sure the wine is stored properly and
that the corks are in contact with the bottles‘
contents.
Roller Assembly. All shelves have a roller
assembly, which enables you to have a threequarter extension for easy access to all bottles
of stored wine.
Service Alert. An indicator light will let you
know if service may be necessary.
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer.
Home Alarm. Wiring connections give you the
option of hooking the Wine Storage unit up to
your home security system.
Discreet Lighting. Our soft low-wattage lighting
is independent of door opening.
Correct Temperature. The range of each
temperature zone is 3˚C to 18˚C, and your set
temperature is digitally displayed in the control
panel.
Humidity. Proper humidity is maintained
throughout the entire unit.
UV Protection. The tinted glass minimizes the
amount of ultraviolet light entering the unit.
Lock. A lock will be offered as an option for all
Wine Storage models. The lock is offered as a
sales accessory and should be ordered through
your Sub-Zero dealer. Special planning is necessary when ordering locks for Models I427 and
I427R; see page 57 for details.
Tight Seal. Magnetic gaskets around the doors
give extra-tight seals.
Kickplate. The solid, adjustable kickplate gives a
true built-in look and conforms to American
Institute of Architects standards.
Front Venting. All Sub-Zero Wine Storage
models are designed for mechanical system
airflow at the front of the appliance. Decorative
panels must not cover louvered surfaces or
prevent removal of louvered components.
47
MODEL I424
MODEL I424FS
MODEL I427
UNDERCOUNTER
B U I LT- I N
UNDERCOUNTER
FREE-STANDING
ALL WINE STORAGE
MODEL OPTIONS
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Overlay Design
I424/O
Overall Width
616 mm
Overall Width
686 mm
Classic Stainless Steel
I424/S
Overall Height
868 mm
Overall Height
2032 mm
Overall Depth
625 mm
Overall Depth
610 mm
S P E C I F I C AT I O N S
Wine Storage Capacity
46 bottles*
Wine Storage Capacity
132 bottles*
Overall Width
606 mm
Door Swing Clearance
645 mm
Min Height Required
2019 mm
864 mm
Specify Door Swing
LH or RH
Door Swing Clearance
648 mm
610 mm
Shipping Wt
100 kg
Specify Door Swing
LH or RH
Shipping Wt
179 kg
Overall Height
Overall Depth
Wine Storage Capacity
46 bottles*
Min Height Required
870 mm
F E AT U R E S
Door Swing Clearance
645 mm
2 Temperature Zones
F E AT U R E S
Specify Door Swing
LH or RH
8 (750 ml) Bottles per Standard Shelf
2 Temperature Zones
Shipping Wt (glass)
86 kg
2 Top Zone Shelves (16 bottles*)
9 (750 ml) Bottles per Standard Shelf
Shipping Wt (glass/S)
88 kg
3 Bottom Zone Shelves (24 bottles*)
5 Top Zone Shelves (45 bottles*)
1 Fixed Bottle Holder (6 bottles*)
9 Bottom Zone Shelves (81 bottles*)
F E AT U R E S
Full-View Glass Door
1 Display Shelf (6 bottles*)
2 Temperature Zones
Classic Stainless Steel Exterior
and Door Frame
Full-View Glass Door
8 (750 ml) Bottles per Standard Shelf
2 Top Zone Shelves (16 bottles*)
PANEL OPTIONS
3 Bottom Zone Shelves (24 bottles*)
Integrated
1 Fixed Bottle Holder (6 bottles*)
Classic stainless steel finish
(includes handle)**
Full-View Glass Door
MODEL I424
48
MODEL I424FS
MODEL I427
MODEL I430
MODEL I427R
ALL WINE STORAGE
W I N E S T O R A G E | R E F R I G E R AT O R
MODEL OPTIONS
*750 ml bottles.
S P E C I F I C AT I O N S
Overlay Design
I430/O
Overall Width
686 mm
Classic Stainless Steel
I430/S
Overall Height
2032 mm
Overall Depth
610 mm
S P E C I F I C AT I O N S
Wine Storage Capacity
78 bottles*
Overall Width
762 mm
Refrigerator Capacity
150 L
2134 mm
Min Height Required
2019 mm
610 mm
Door Swing Clearance
648 mm
147 bottles*
Specify Door Swing
LH or RH
2108 mm
Drawer Clearance
495 mm
Door Swing Clearance
765 mm
Shipping Wt
186 kg
Specify Door Swing
LH or RH
Shipping Wt
197 kg
F E AT U R E S
Shipping Wt (glass /S)
202 kg
3 Temperature Zones
Overall Height
Overall Depth
Wine Storage Capacity
Min Height Required
**Optional stainless steel panels and
handles are ordered and shipped as
sales accessories.
2 Refrigerated Drawers
F E AT U R E S
9 (750 ml) Bottles per Standard Shelf
2 Temperature Zones
6 Top Zone Shelves (54 bottles*)
10 (750 ml) Bottles per Standard Shelf
2 Bottom Zone Shelves (18 bottles*)
5 Top Zone Shelves (50 bottles*)
1 Display Shelf (6 bottles*)
9 Bottom Zone Shelves (90 bottles*)
Full-View Glass Door
1 Display Shelf (7 bottles*)
Full-View Glass Door
PANEL OPTIONS
Integrated
Classic stainless steel finish
(includes handles)**
ACCESSORIES
Contact your Sub-Zero Dealer
Classic stainless steel front
panels (Models I427 and I427R)*
Tubular handles in classic
stainless steel
Side and grille panels
(Model I430)*
MODEL I430
MODEL I427R
Panel, louvered or stainless
steel grilles in varied heights
(Model I430)*
Dual installation heater kit
(Models I427 and I427R)*
*Accessory is available only for
models listed.
49
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer.
I N S TA L L AT I O N
Refer to the
installation instructions shipped with
each Sub-Zero
product for detailed
specifications.
PLANNING INFORMATION
ELECTRICAL REQUIREMENTS
Review the Overall Dimensions and Installation
Specifications illustrations for your Wine Storage
model on the following pages. These specifications cover all the details you need to know
about space allocation and placement of electrical, whether the models are overlay, stainless
steel or integrated.
International models from the factory designed
without a transformer require a 220/240 V AC,
50/60 Hz electrical supply, fused at the correct
rating for the unit. If required by local or national
codes, the power cord can be easily replaced
using the power inlet device.
For corner installations, you need allow for a
minimum 76 mm filler so the door can open to
90˚. If you are using larger handle hardware, you
will also need to take that into account.
International models using a factory installed
transformer require a 220/240 V AC, 50/60 Hz
electrical supply, fused at the correct rating for
the unit. These models will come equipped with
Schuko power cords. The power cord may need
to be replaced depending on local and national
codes. The USA power cord that is supplied with
the product must be disconnected with the
appropriate transformer output to be connected
in its place.
For a maximum 90˚ door opening, use the door
stop built into the hinge system of Model I427.
An optional 90˚ door stop kit for Model I430 is
available from your Sub-Zero dealer.
IMPORTANT NOTE: The electrical outlet must
be grounded. The outlet must be flush with the
back wall. Refer to the Installation Specifications
illustration for your model for exact placement.
If you will be connecting the unit to a home
security system, you must allow a minimum of
914 mm of the system‘s wiring to be routed in
the electrical area designated for your model.
IMPORTANT NOTE: A ground fault circuit
interrupter (GFCI) is not recommended and may
cause interruption of operation.
All Wine Storage models must be installed so
that the door can open a minimum of 90˚ or you
will have problems pulling the wine shelves out.
Refer to the door clearance and door swing
information.
IMPORTANT NOTE: The anti-tip bracket must be
installed to prevent the unit from tipping
forward.
DUAL INSTALLATIONS
If you are installing a Wine Storage unit next to
an existing Sub-Zero unit, you may have to allow
for a filler strip.
If you are installing a Model I427 or I427R Wine
Storage unit next to an existing Integrated
Sub-Zero unit, with 51 mm or less between the
units, an optional heater kit (BBDUAL or
TTDUAL) will need to be installed to prevent
moisture from forming between the units. This
optional kit is available through your Sub-Zero
dealer.
50
OVERALL DIMENSIONS
Undercounter Wine Storage
606 mm
587 mm
625 mm
616 mm
(CABINET DIMENSION)
597 mm DOOR FRAME
(CABINET DIMENSION)
UNDERCOUNTER
273 mm
864
mm*
CENTERED
VERTICALLY
Model I424
Built-In
868
mm*
767
mm
Model I424FS
Free-Standing
DOOR
FRAME
102
mm
102 mm
FRONT VIEW
TOE KICK
SIDE VIEW
FRONT VIEW
*13 mm +_ ADJUSTMENT IN LEVELING LEGS
SIDE VIEW
*13 mm +_ ADJUSTMENT IN LEVELING LEGS
MODEL I424
MODEL I424FS
Built-In
Free-Standing
Width
606 mm
Width
616 mm
Height 864 mm
Height 868 mm
Depth
Depth
610 mm
625 mm
Note the location of pre-drilled
holes for optional handle hardware.
I N S TA L L AT I O N S P E C I F I C AT I O N S
Undercounter Models
610 mm
ROUGH
OPENING
DEPTH
Model I424
A) Rough Opening Width
610 mm
B) Rough Opening Height 876 mm
90˚
C) Min Door Clearance
644 mm
D) Min Clearance at 90˚
660 mm
TOP VIEW
C) Min Door Clearance
644 mm
ROUGH OPENING
WIDTH
D) Min Clearance at 90˚
660 mm
C
Model I424FS*
A
*Free-standing Model I424FS requires no
surrounding cabinetry.
D
B
Dimensions are for finished rough openings.
LOCATE ELECTRICAL
WITHIN SHADED AREA
Door swing clearances are based on
stainless steel door and handle dimensions.
114
mm
ROUGH
OPENING
HEIGHT TO
FINISHED
FLOORING
394 mm
E
64 mm
FRONT VIEW
51
OVERALL DIMENSIONS
All Wine Storage – Model I427
Wine Storage | Refrigerator – Model I427R
686 mm
664 mm DOOR FRAME
356 mm
686 mm
664 mm DOOR FRAME
356 mm
610 mm
(UNIT DIMENSION)
610 mm
(UNIT DIMENSION)
I N T E G R AT E D
20
mm
20
mm
Model I427
All Wine Storage
1139
mm
Model I427R
Wine Storage |
Refrigerator
273 mm
OVERALL
DIMENSIONS
1997
mm*
CENTERED
VERTICALLY
DOOR
FRAME
WITH
HINGES
273 mm
2032
mm
CENTERED
VERTICALLY
2032
mm
1789
mm
DOOR
FRAME
WITH
HINGES
1997
mm*
9 mm
Model I427 | I427R
Width
686 mm
Height
2032 mm
Depth
610 mm
Note the location of
pre-drilled holes for
optional handle
hardware.
337
13 mm
mm
650 mm
DRAWER FRONT
877
mm*
260
mm
517
mm
227
mm
FRONT VIEW
102
mm
SIDE VIEW
*13 mm +_ ADJUSTMENT IN LEVELING LEGS
248
mm
102
mm
FRONT VIEW
SIDE VIEW
*13 mm +_ ADJUSTMENT IN LEVELING LEGS
I N S TA L L AT I O N S P E C I F I C AT I O N S
Models I427 | I427R
635 mm
ROUGH
OPENING
DEPTH
Dimensions are for finished rough openings.
Door swing clearances are based on
stainless steel door and handle dimensions.
IMPORTANT NOTE: The depth of Models
I427 and I427R is 610 mm from the front of
the unit to its back. Your design may necessitate moving the unit back or cabinets
forward to achieve a flush fit. This will
require a minimum rough opening depth of
635 mm.
TOP VIEW
606 mm
2032 mm
686 mm
ROUGH OPENING
HEIGHT
TO FINISHED
FLOORING
ROUGH OPENING WIDTH
2019 mm
MIN HEIGHT
REQUIRED
105˚
90˚
648 mm
MAXIMUM
DOOR SWING
648 mm
LOCATE ELECTRICAL
WITHIN SHADED AREA
711 mm
889 mm
DOOR CLEARANCE
DOOR CLEARANCE
114
mm
394 mm
E
64 mm
52
FRONT VIEW
ANTI-TIP BRACKET
OVERALL DIMENSIONS
All Wine Storage – Model I430
762 mm
606 mm
719 mm DOOR FRAME
ALL WINE
STORAGE
Model I430
Built-In
CENTERED VERTICALLY
2134
mm
OVERALL
DIMENSIONS
Model I430
273
mm
1724
mm
DOOR
FRAME
Width
762 mm
Height
2134 mm
Depth
610 mm
Note the location of
pre-drilled holes for
optional handle
hardware.
FRONT VIEW
105
mm
TOE
KICK
SIDE VIEW
*13 mm ADJUSTMENT IN LEVELING LEGS
I N S TA L L AT I O N S P E C I F I C AT I O N S
I N S TA L L AT I O N
All Wine Storage – Model I430
610 mm
Refer to the
installation instructions shipped with
each Sub-Zero
product for detailed
specifications.
ROUGH
OPENING
DEPTH
Dimensions are for finished rough openings.
Door swing clearances are based on
stainless steel door and handle dimensions.
TOP VIEW
ANTI-TIP BLOCK
606 mm
178
mm
BEHIND
FRAME
E
152
mm
LOCATE ELECTRICAL
WITHIN SHADED AREA
130˚
90˚
765 mm
MAXIMUM
DOOR SWING
765 mm
2127 mm
749 mm
ROUGH OPENING
HEIGHT
TO FINISHED
FLOORING WITH
STANDARD
279 mm GRILLE
ROUGH OPENING WIDTH
838 mm
1270 mm
2108 mm
DOOR CLEARANCE
DOOR CLEARANCE
MIN HEIGHT
REQUIRED
(LEVELERS IN)
1918 mm
FRONT VIEW
53
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer.
54
DOOR PANELS
MODEL I424FS – FREE-STANDING
Unless you are installing a stainless steel model,
you will need to provide a frame for the glass
door. If you order a stainless steel unit, Models
I424, I424FS and I430 will be shipped with their
panels and hardware installed and you will
merely install the Sub-Zero. However, for Models
I427 and I427R, you will have to have the stainless steel panels and handles installed.
The free-standing Model I424FS does not require
any panels or surrounding cabinetry. It has a
beautiful classic stainless steel exterior, door
frame and handle. Refer to the Overall Dimensions illustration for the Model I424FS.
OVERLAY PANELS – MODEL I424
The overlay panel applied to Model I424 should
not be confused with the Built-In overlay panel
application. The overlay panel will consist of only
a frame and would be either the 16 mm or 19
mm thick panel you may be using. It is affixed
directly to the door itself with screws through a
series of pre-drilled holes in the perimeter of the
door itself. You do not need any backer or
spacer panel.
Refer to the Overall Dimensions and Cabinetry
Dimensions illustrations for Model I424 to give
you a better idea of the exact space our unit
needs and how the panel fits in relationship with
the unit.
The Overall Dimensions illustrations show the
location of predrilled holes for optional handle
hardware. Refer to page 60 for specifics about
installing handles on this overlay application.
IMPORTANT NOTE: When planning to install the
Model I424 next to adjoining cabinetry, you must
make provisions to allow the door to open to a
maximum of 145˚ and not interfere with the door
panel. Refer to the full-scale illustration at the
end of this section.
To install overlay
panels, see the
detailed procedures
outlined in the
Sub-Zero Wine
Storage Installation
Guide.
The glass door opening of the standard Model
I424 is designed to be exposed to room air circulation. Decorative overlays on the glass should
be kept to a minimum. Also, rails and stiles can
be increased in size but should not exceed
cabinet manufacturers‘ standard width. They
cannot exceed overall door panel dimensions
specified, as they would interfere with the operation of the door. The back sides of rails and
stiles that will be visible through the glass door
will need to be finished. Also, the inside edges
of the frames must be finished to match the
front surface.
CABINETRY DIMENSIONS
O V E R L AY PA N E L S P E C I F I C AT I O N S
Model I424
Model I424
606 mm
606 mm**
(CABINET DIMENSION)
603 mm DOOR PANEL
I N S TA L L AT I O N
Door Panel Width
603 mm
Door Panel Height
764 mm
Min Width of Rails and Stiles
57 mm
Door Frame Panel Weight Limit 5 kg
877
mm*
Min Panel Thickness
764 mm
16 mm
DOOR
PANEL
CENTERED
VERTICALLY
FRONT VIEW
102
mm
TOE
KICK
SIDE VIEW
*13 mm ADJUSTMENT IN LEVELING LEGS
** MODEL I424/S (STAINLESS STEEL WRAPPED DOOR) FINISHES OFF AT 606 mm DEEP
55
INTEGRATED PANELS –
MODELS I427 | I427R
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer.
The integrated frame panels for glass doors for
these models will follow some of the identical
planning processes used with the Integrated line.
The installation of the door panels is completely
different, however. Rather than using the
mounting hardware we used with the Integrated
line, door panels for both Models I427 and I427R
will be applied with screws applied through our
door.
The drawer panels for the Model I427R will be
applied using the Integrated technique of
mounting brackets.
Refer to the Overall Dimensions and Cabinetry
Dimensions illustrations for Models I427 and
I427R to give you a better idea of the exact
space our unit needs and how the panel fits in
relationship with the unit.
IMPORTANT NOTE: The depth of Models I427
and I427R is 610 mm from the front of the unit
to its back. You must allow for the thickness of
the panel you are applying when planning for the
finished rough opening depth if you want the
front panel to be flush with surrounding cabinetry. You may have to move the unit back into
the drywall or bring the cabinets forward. Refer
to pages 37–43 of the Integrated section.
IMPORTANT NOTE: The glass door opening of
the standard Models I427 and I427R is designed
to be exposed to room air circulation. Decorative
overlays on the glass should be kept to a
minimum. While the cabinet front stiles are a
minimum of 57 mm for both Models I427 and
I427R, the top and bottom rails are different.
Rails and stiles can be increased in size but
should not exceed cabinet manufacturers‘
standard width. They cannot exceed overall door
panel dimensions specified, as they would interfere with the operation of the door. The back
sides of rails and stiles that will be visible
through the glass door will need to be finished.
Also, the inside edges of the frames must be
finished to match the front surface.
IMPORTANT NOTE: The inside edges of the
rough opening will need to be finished as they
will be exposed when the doors are open.
CABINETRY DIMENSIONS
I N T E G R AT E D PA N E L S P E C I F I C AT I O N S
Model I427
Model I427
686 mm
610 mm
FINISHED OPENING
(UNIT DIMENSION)
679 mm DOOR PANEL
Door Panel Width
679 mm
Door Panel Height
1927 mm
Min Width of Top Rail
Min Width of Bottom Rail
Min Width of Stiles
Door Frame Panel Weight Limit
2032
mm
Min Panel Thickness
FINISHED
OPENING
1927
mm
2029
mm
DOOR
PANEL
TRIMMED
DOOR
102
mm
102
mm
TOE KICK
FRONT VIEW
TOE KICK
SIDE VIEW
NOTE: 13 mm ADJUSTMENT IN LEVELING LEGS
56
95 mm
203 mm
57 mm
9 kg
16 mm
IMPORTANT NOTE: The dimensions of these
panels and stiles are assuming the models finish
off at 2032 mm in height overall and have a 102
mm toe kick for the Model I427. If you finish off
at 2134 mm, for instance, you must add 102
mm additional to the overall height of the panel
and remember to add 102 mm to the top rail.
Likewise, if you allow for a 152 mm toe kick for
the Model I427, you must subtract 51 mm from
the bottom rail.
Door panels for Models I427 and I427R can
grow beyond the 2032 mm height to accommodate any size door as long as you stay below
door panel weight limit of 9 kg. Refer to the
specifications under Door Panel Height on page
43 of the Integrated section.
IMPORTANT NOTE: If you are installing
Sub-Zero‘s optional lock kit on a Model I427 or
I427R, you may have to order door panels that
exceed the 2032 mm finished height. Consult
the lock kit installation instructions and see if
your panels will allow for an adequate installation.
IMPORTANT NOTE: In the panel specifications
for Model I427R, the bottom drawer panel height
is based on a 102 mm toe kick. If you want to
show a 152 mm toe kick, you must subtract 51
mm from the bottom drawer panel height.
I N S TA L L AT I O N
To install integrated
panels, see the
detailed procedures
outlined in the
Sub-Zero Wine
Storage Installation
Guide.
IMPORTANT NOTE: The toe kick area on the
Model I427 cannot be larger than 152 mm, and
no larger than 229 mm for the 427R. The toe
kick area for either model cannot be less than
102 mm.
Please note in the Overall Dimensions illustrations the location of pre-drilled holes for optional
handle hardware. Refer to page 60 for specifics
about installing handle hardware on this overlay
application.
CABINETRY DIMENSIONS
I N T E G R AT E D PA N E L S P E C I F I C AT I O N S
Model I427R
Model I427R
686 mm
610 mm
FINISHED OPENING
(UNIT DIMENSION)
679 mm DOOR PANEL
Door Panel Width
679 mm
Door Panel Height
1153 mm
Min Width of Top Rail
95 mm
Min Width of Bottom Rail
76 mm
Min Width of Stiles
57 mm
Door Frame Panel Weight Limit
1153
mm
Top Drawer Panel Width
679 mm
FINISHED
OPENING
Top Drawer Panel Height
345 mm
Bottom Drawer Panel Width
679 mm
Bottom Drawer Panel Height
2029
mm
3
mm
Drawer Panel Weight Limit
TRIMMED
DOOR
345
3 mm
mm
9 kg
2032
mm
Min Panel Thickness
424 mm
5 kg each
16 mm
679 mm
DRAWER PANEL
877
mm*
424 mm
102
mm
TOE KICK
102
mm
FRONT VIEW
TOE KICK
SIDE VIEW
*13 mm ADJUSTMENT IN LEVELING LEGS
57
OVERLAY PANELS – MODEL I430
Your overlay model will be shipped without
handle hardware and with an 279 mm overlay
panel grille as standard equipment. You will need
to order a panel for the grille and hardware to
complement your surrounding cabinetry.
While the overlay panel design offers you a more
seamless appearance, you need to be aware of
adjacent cabinets and/or countertops when the
door is opened. Refer to the full-scale illustrations at the end of the Built-In section.
To achieve the overlay look, you need three
different panels—the decorative overlay panel, a
3 mm spacer panel and a 6 mm backer panel.
Depending on your cabinet manufacturer, this
could be one panel routed for different dimensions or more likely, three different panels. Refer
to the Overlay Panel Specifications for complete
details on the overlay sizing. In addition, illustrations 2 and 3 will give you a better idea of the
panel construction and how it interacts with our
frame.
The glass door opening of the standard Model
I430 is designed to be exposed to room air circulation. Decorative overlays on the glass should
be kept to a minimum. Also, rails and stiles can
be increased in size but should not exceed
cabinet manufacturers‘ standard width. They
cannot exceed overall door panel dimensions
specified, as they would interfere with the operation of the door.
Trim Reveal 6 mm min
Rout to 6 mm thickness
57 mm Rail / Stile
3
mm
57 mm
Overlay Panel
3 mm Spacer Panel
Door
Frame
Spacer Panel
Overlay Panel
6 mm Backer Panel
8 mm min
Rail/Stile
Door Frame
16
mm
Illus. 1
58
4 mm
2 mm
Glass
Illus. 2
Glass
16
mm
min
Backer
Panel
Door / Grille
Trim
3 mm 6 mm
Illus. 3
The back sides of rails and stiles that will be
visible through the glass door will need to be
finished. Also, the inside edges of the frames
must be finished to match the front surface.
In addition, side panel information for a Model
I430 is available on page 21 of the Built-In
section. Refer to illustration 11 on page 21 for
placement of toe kick and grille area cut-outs.
As with the Sub-Zero Built-In models, you have
the flexibility of ordering grilles in a variety of
heights for the overlay application. Overlay grille
panel dimensions for the overlay Model I430,
standard 279 mm grille, are listed below. Refer
to page 23 for optional grille height dimensions.
The width of the overlay grille, spacer and
backer panel will be the same regardless of the
height.
I N S TA L L AT I O N
To install overlay
panels, see the
detailed procedures
outlined in the
Sub-Zero Wine
Storage Installation
Guide.
CABINETRY DIMENSIONS
O V E R L AY PA N E L S P E C I F I C AT I O N S
Model I430
Model I430 – Overlay (O)
762 mm
722 mm DOOR FRAME
Overlay Door Panel Width
722 mm
Overlay Door Panel Height
1727 mm
Spacer Panel Width
699 mm
Spacer Panel Height
1073 mm
Backer Panel Width
714 mm
Backer Panel Height
1719 mm
Min Width of Rails and Stiles
Door Frame Panel Weight Limit
2134
mm
Min Panel Thickness
1727 mm
Model I430 – Overlay (O)
Overlay Grille Panel Width
722 mm
Overlay Grille Panel Height*
260 mm
Spacer Panel Width
699 mm
Spacer Panel Height*
236 mm
Backer Panel Width
714 mm
Backer Panel Height*
252 mm
Grille Panel Weight Limit
103 mm
11 kg
16 mm
G R I L L E PA N E L S P E C I F I C AT I O N S
DOOR
PANEL
CENTERED
VERTICALLY
FRONT VIEW
57 mm
TOE
KICK
SIDE VIEW
Min Panel Thickness
7 kg
16 mm
NOTE: 13 mm ADJUSTMENT IN LEVELING LEGS
*Grille panel dimensions are for standard 279 mm
grille. Refer to page 22 for optional grille heights.
59
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer.
HARDWARE CONSIDERATIONS
WINE SHELF WOOD FACING
With Model I424 (overlay), Models I427 and
I427R (integrated) and Model I430 (overlay), you
must supply your own handle hardware. It is
recommended you use our optional handles and
use the pre-drilled holes supplied to locate the
handles within the frame of our unit. The metal
frame on the door has numerous mounting holes
on each side to accommodate Sub-Zero accessory handles. This will allow you to provide the
best possible handle alignment and not take
away from the strength of the stile in this area
after the unit is used a number of times. We
recommend using a pull handle and not a pull
knob.
Sub-Zero has provided a natural cherry wood
facing to its wine storage shelves in each model.
You can also replace these strips with wood
more complementary to your design and
surrounding cabinetry.
If you elect to place different hardware on these
units, we encourage you to fasten the hardware
by passing through our door and attaching the
hardware through the Sub-Zero door‘s frame.
Optional stainless steel handles are available in a
variety of diameters and lengths, as are handles
to match the style of Wolf ovens. Contact your
Sub-Zero dealer for specifics.
When planning for hardware, refer to the
Door Frame Profile full-scale illustration on
the following page to give you a better
understanding of the unit‘s frame and positioning of the glass for the door. You must
not drill through this glass.
60
The Wine Shelf Wood Facing illustration on the
following page can be used as a full-scale
template. You must follow the layout of this
format to accommodate the shelves properly. To
remove the cherry strips, take the shelves out
and remove the screws. Reverse the procedure
to affix the new wood.
If you choose to stain or seal the wood facing,
be aware that some of these substances are
hazardous and will damage stored wine.
DOOR FRAME PROFILE
DOOR FRAME HANDLE OFFSET
Wine Storage Models
Glass
Cabinet Door
Profile
CL
A
Dimension A
Model I424
25 mm
Model I427
22 mm
Model I427R
22 mm
Model I430
24 mm
IMPORTANT NOTE: Rails and stiles must be
a minimum of 57 mm wide (except for the
rails of Models I427 and I427R, which must
be wide enough to cover the door hinges).
The back sides of rails and stiles that will be
visible through the glass door will need to be
finished.
A
57 mm Rail /Stile
This full-scale illustration is typical of the
Model I424 door frame profile; details of the
other Wine Storage door frames will vary slightly.
FULL-SCALE
T E M P L AT E S
The full-scale illustrations on the
following pages
enable you to understand some of the
unique situations
you may face as you
plan for the installation of the Wine
Storage units. Use
these illustrations as
templates.
WINE SHELF WOOD FACING
16 mm
Maximum Thickness
3 mm
38 mm
21 mm
2 mm
A (WIDTH)
9 mm
14 mm
SIDE VIEW
FRONT VIEW
This full-scale illustration provides the dimensions
you will need should you choose to replace the
natural cherry wood facing of each wine shelf
with wood more complementary to your design
and surrounding cabinetry.
W I N E S H E L F W O O D FA C I N G
Wine Storage Models
Dimension A
Model I424
495 mm
Model I424FS
495 mm
Model I427
532 mm
Model I427R
532 mm
Model I430
624 mm
61
MODEL I424 – DOOR CLOSED AND 145˚ MAX OPENING
610 mm
CABINETRY
OPENING
587 mm
TO BACK OF
APPLIANCE
*MODEL I424 MUST
EXTEND A MINIMUM
6 mm BEYOND THE
FRONT SURFACE OF
ADJOINING
CABINETRY TO
ALLOW THE MAXIMUM
DOOR SWING
SUB-ZERO DOOR
19 mm
13
mm
DOOR PANEL
6 mm*
3 mm
600 mm
DOOR PANEL
WIDTH
DOOR
PANEL
145˚*
The full-scale illustration shows what
considerations you need to make for the
installation of Model I424 and how the
maximum door opening may interact with
adjacent cabinets and countertops.
62
SUB-ZERO
DOOR
NEW UNDERCOUNTER REFRIGERATION
Available in 2007
NEW
A L L R E F R I G E R AT O R
606 mm
Aside from the full-size models that Sub-Zero
offers in its Built-In and Integrated lines of refrigeration and its Wine Storage equipment, we
round out our product line-up with a new line of
Undercounter refrigeration available in 2007.
Our new Undercounter line consists of an all
refrigerator model, an all refrigerator beverage
center, a refrigerator / freezer combination model
and an all refrigerator model designed for
outdoor applications. The existing ice maker
Model 315IP will continue to be offered.
The Undercounter models accept a decorative
door panel for an overlay or stainless steel
application and can be built in to fit flush with
virtually any base cabinet style. The outdoor
Model UC-24RO is available in classic stainless
steel only and comes with door panel and
handle in place. Model UC-24RO must also be
built-in into cabinetry and is not designed to be a
free-standing unit.
A classic stainless steel door panel with handle
is available as a sales accessory for Models
UC-24R and UC-24C. Contact your Sub-Zero
dealer for information on accessory panels and
handles. Model UC-24B must be ordered as
overlay (UC24-B/O) or stainless steel (UC-24B/S).
Optional stainless steel panels and handles for
Model 315IP are offered in classic stainless
steel.
864
mm
MODEL UC-24R
All Refrigerator
NEW
BEVERAGE CENTER
606 mm
864
mm
MODEL UC-24B
All Refrigerator
NEW
C O M B I N AT I O N
606 mm
864
mm
MODEL UC-24C
Combination
Refrigerator / Freezer
NEW
OUTDOOR MODEL
606 mm
864
mm
MODEL UC-24RO
All Refrigerator
ICE MAKER
386
mm
854
mm
Comprehensive installation
instructions are shipped with each
model. Refer to those instructions
in preparing and installing all
Sub-Zero products. The instructions
can also be found on our website,
subzero.com.
MODEL 315IP
Ice Maker
63
MODEL UC-24R
NEW
A L L R E F R I G E R AT O R
MODEL UC-24B
NEW
BEVERAGE CENTER
MODEL UC-24C
NEW
C O M B I N AT I O N
R E F R I G E R AT O R | F R E E Z E R
MODEL OPTIONS
S P E C I F I C AT I O N S
Overlay Design
UC-24B/O
Classic Stainless Steel
UC-24B/S
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
Overall Width
606 mm
Overall Width
606 mm
Overall Width
606 mm
Overall Height
864 mm
Overall Height
864 mm
Overall Height
864 mm
Overall Depth
610 mm
Overall Depth
610 mm
Overall Depth
610 mm
Refrigerator Capacity
161 L
Refrigerator Capacity
161 L
Refrigerator Capacity
102 L
Min Height Required
870 mm
Wine Storage Capacity
16 bottles*
Wine Storage Capacity
8 bottles*
Door Swing Clearance
645 mm
Min Height Required
870 mm
Freezer Capacity
31 L
Specify Door Swing
LH or RH
Door Swing Clearance
645 mm
Min Height Required
870 mm
Shipping Weight
59 kg
Specify Door Swing
LH or RH
Door Swing Clearance
645 mm
Shipping Weight (O)
59 kg
Specify Door Swing
LH or RH
Shipping Weight (S)
61 kg
Shipping Weight
59 kg
F E AT U R E S
F E AT U R E S
F E AT U R E S
2 Adjustable Glass Shelves
2 Wine Storage Shelves
1 Wine Storage Shelf
1 Utility Bin
1 Adjustable Glass Shelf
1 Adjustable Glass Shelf
2 Door Shelves
1 Utility Bin
1 Door Shelf
Full-View Glass Door
Automatic Defrost
Automatic Ice Maker
MODEL UC-24R
*750 ml bottles
Optional stainless steel panels and
handles are ordered and shipped as
sales accessories for Models UC-24R,
UC-24C and 315IP.
64
MODEL UC-24B
MODEL UC-24C
MODEL UC-24RO
NEW
MODEL 315IP
A L L R E F R I G E R AT O R
OUTDOOR MODEL
ICE MAKER
S P E C I F I C AT I O N S
S P E C I F I C AT I O N S
ACCESSORIES
606 mm
Overall Width
386 mm
Overall Height
864 mm
Overall Height
854 mm
Overall Depth
610 mm
Overall Depth
610 mm
161 L
Ice Storage Capacity
12 kg
870 mm
Min Height Required
857 mm
645 mm
Door Swing Clearance
387 mm
Specify Door Swing
LH or RH
Shipping Weight
45 kg
Shipping Weight
59 kg
Overall Width
Refrigerator Capacity
Min Height Required
Door Swing Clearance
F E AT U R E S
F E AT U R E S
2 Adjustable Glass Shelves
Automatic Ice Maker
1 Utility Bin
Automatic Defrost
2 Door Shelves
Reversible Door Swing
Door Lock
Drain Pump
Optional accessories
are available
through your
Sub-Zero dealer.
Classic Stainless Steel Finish
PANEL OPTIONS
Custom Wood Panel
Classic stainless steel finish
(includes handle)
MODEL UC-24RO
MODEL 315IP
ACCESSORIES
Contact your Sub-Zero Dealer
Classic stainless steel door front
panel with tubular handle
Classic stainless steel tubular
handle for overlay application
UL approved door lock
65
UNDERCOUNTER FEATURES
UNDERCOUNTER MODEL FEATURES
Overlay Application. The overlay application
blends seamlessly into your overall room design
and complements surrounding cabinetry. You add
the decorative door front panel and hardware.
Sub-Zero accessories handles are available. The
overlay application is available for all Undercounter models except Model UC-24RO. Model
UC-24B must be ordered specifically as overlay
(UC24-B/O).
Electronic Controls. The electronic controls with
digital readout LCD display are up front and easy
to access.
ACCESSORIES
Optional accessories
are available
through your
Sub-Zero dealer.
Stainless Steel Application. Classic stainless
steel door front panel and handle is available as
an accessory for Models UC-24R, UC-24C and
315IP. Model UC-24B must be ordered specifically as stainless steel (UC24-B/S). Model
UC-24RO is available as a classic stainless steel
model only and comes with door panel and
handle in place.
Glass Shelves. The cantilevered glass shelves
are adjustable, easy to clean and spill proof. The
glass floor is also spill proof.
Utility Bin. All units except Model UC-24C
feature a clear utility bin for storage of smaller
items.
Wine Storage. Models UC-24B and UC-24C
feature wine storage of 16 and 8 (750 ml)
bottles, respectively. The roller-glide wine
storage shelves faced with natural cherry wood
have a three-quarter extension for easy access.
Glass Door—Model UC-24B. The full-view glass
door and accent lighting of Model UC-24B
matches the appearance of Wine Storage Model
I424.
Ice Maker. Model UC-24C refrigerator/freezer
features an automatic ice maker with clear ice
bucket. The ice maker provides high-quality,
crescent-shaped ice that won’t stick to the side
of the glass.
Two-Litre Bottle Storage. All units except Model
UC-24B feature two-litre bottle storage in the
bottom door shelf.
Door Lock. A UL approved lock is standard on
Model UC-24RO and available as a sales accessory for all other models.
Sabbath Feature. The Sabbath feature will allow
the lights to remain off during certain religious
observances.
315IP MODEL FEATURES
Built-in pump to allow water to drain into an
adjacent sink.
Ice storage capapcity of up to 11.8 kg.
66
PLANNING INFORMATION
ELECTRICAL REQUIREMENTS
Refer to the Installation Specifications for information regarding area requirements, minimum
door clearance, placement of electrical and
plumbing (Models UC-24C and 315IP).
A 115 V AC, 60 Hz, 15 amp circuit breaker and
electrical supply are required. A separate circuit,
servicing only this appliance is required.
PLUMBING REQUIREMENTS
For Models UC-24C and 315IP, rough in the
water supply line. Connect a 6.35 mm OD
copper line to the house supply with an easily
accessible shut-off valve between the supply
and the unit. A minimum of 660 mm of copper
tubing is required for the water line.
Do not use self-piercing valves. A saddle valve
kit (4200880) is available from your Sub-Zero
dealer. An in-line filter is required when water
conditions have a high sediment content.
All Undercounter models are equipped with a
power supply cord with a 3-prong grounding
plug, which must be plugged into a mating
3-prong grounding-type wall receptacle. Follow
local codes and ordinances when installing the
receptacle. Refer to the Installation Specifications illustrations.
IMPORTANT NOTE: The Model UC-24RO is
designed and safe for use in outdoor applications. When installed outdoors, a ground fault
circuit interrupter (GFCI) is required to reduce
the risk of electrical shock. A GFCI is not
recommended for use with other Undercounter
models and may cause interruption of operation.
The ice maker operates on constant water
pressure between 1.4 bar and 6.9 bar.
MODEL OPTIONS
Model UC-24R
All Refrigerator
Model UC-24B
All Refrigerator
Beverage Center
Model UC-24C
Refrigerator | Freezer
with Ice Maker
Model UC-24RO
All Refrigerator
Outdoor Model
IMPORTANT NOTE: In some cases, a reverse
osmosis water filter system may not be able to
maintain the minimum pressure consistently.
Model 315IP
Ice Maker with
Drain Pump
I N S TA L L AT I O N S P E C I F I C AT I O N S
51 mm
Undercounter Models
394 mm
13 mm
LOCATE WATER LINE
(MODEL UC24C ONLY)
WITHIN SHADED AREA
Overall Dimensions
Overall Width
606 mm
Overall Height
864 mm
Overall Depth
610 mm
610 mm
ROUGH
OPENING
DEPTH
TOP VIEW
Finished Opening Dimensions
Opening Width
610 mm
Opening Height
876 mm
Opening Depth
610 mm
Door Swing Clearance
645 mm
610 mm
ROUGH OPENING
WIDTH
Model 315IP
ANTI-TIP BRACKET
Min Door Clearance
387 mm
Water Supply
203 mm
876 mm
LOCATE ELECTRICAL
AND WATER LINE
(MODEL UC24C ONLY)
WITHIN SHADED AREA
Models without an ice maker will not require
the water line connection.
For Model 315I(P), the electrical supply can
be located anywhere on the back wall.
394 mm
Door swing clearance based on stainless
steel door panel and handle dimensions.
76
mm
ROUGH
OPENING
HEIGHT
90˚
644 mm
870 mm
MINIMUM
HEIGHT
REQUIRED
660 mm
DOOR CLEARANCE
51 mm
FRONT VIEW
67
I N S TA L L AT I O N
DRAIN PUMP – MODEL 315IP
DOOR PANEL – MODEL 315IP
This ice maker comes with a built-in drain pump.
The drain and inlet water tubes must be
plumbed before connecting to the ice maker. An
air gap will likely be required between the ice
maker drain tube and the drain/waste receptacle.
A stand pipe with a trap below it would be
acceptable for the drain/waste receptacle. Refer
to the illustrations below.
It is important to understand the differences in
mounting any wood panel to the Model 315IP.
Refer to the installation instructions packaged
with the unit to understand how the panel is
installed. It does not require a 6 mm backer.
Door panel dimensions are 381 mm wide by
772 mm high and must be a minimum of 16 mm
thick. The maximum door panel weight is 7 kg.
No handle recess is required.
IMPORTANT NOTE: Poor drainage will cause a
high rate of ice melting in the bin.
Refer to the
installation instructions shipped with
each Sub-Zero
product for detailed
specifications.
I N S TA L L AT I O N S P E C I F I C AT I O N S
Model 315IP – Drain Pump
SHUT-OFF
VALVE
3 mm
WATER
INLET TUBE
WATER
FILTER
AIR GAP
DEVICE
DRAIN
TUBE
876 mm
NOMINAL
609 mm
AIR GAP
DEVICE
DRAIN
TUBE
857 mm
MIN.
WATER
INLET TUBE
SHUT-OFF
VALVE
387 mm MIN.
TOP VIEW
WATER
FILTER
387 mm MIN.
FRONT VIEW
68
OVERLAY DOOR PANEL –
MODELS UC-24R AND UC-24C
OVERLAY DOOR PANEL –
MODEL UC-24B
The overlay door panel design allows for a
decorative panel to cover the door trim for a
seamless appearance that will compliment
surrounding cabinetry. You may also choose to
match the handle hardware of surrounding
cabinetry.
The overlay door panel applied to the Model
UC-24B will consist of only a frame and will affix
directly to the door with screws through a series
of predrilled holes in the perimeter of the door.
Refer to the Overlay Panel Specifications below
for your specific model. Illustration 1 below
applies to Models UC-24R and UC-24C. Illustration 2 applies to Model UC-24B. Outdoor Model
UC-24RO is available as a classic stainless steel
model only and comes with door panel and
handle in place.
The glass door opening of the Model UC-24B is
designed to be exposed to room air circulation.
Decorative overlays on the glass should be kept
to a minimum. Rails and stiles must be a
minimum of 57 mm wide. They can be increased
in size but should not exceed cabinet manufacturers standard width. Rails and stiles cannot
exceed the overall door panel dimensions specified in the Overlay Panel Specifications, as they
would interfere with the operation of the door.
The back sides of rails and stiles that will be
visible through the glass door will need to be
finished. Also, the inside edges of the frames
must be finished to match the front surface.
I N S TA L L AT I O N
To install framed or
overlay panels, see
the detailed procedures outlined in the
Sub-Zero Undercounter Installation
Guide.
Refer to the fullscale illustrations at
the end of this
section for specifics
on door openings
and other specifications.
O V E R L AY PA N E L S P E C I F I C AT I O N S
Undercounter Models
Models UC-24R and UC-24C
Door Panel Width
Door Panel Height
Panel Thickness
Panel Weight Limit
603 mm
764 mm
H
9 kg max
Model UC-24B
Door Panel Width
603 mm
Door Panel Height
764 mm
Width of Rails and Stiles
57 mm min
Panel Thickness
16 mm min
Panel Weight Limit
H
16 mm min
W
W
Illus. 1
Illus. 2
5 kg max
69
DOOR FRAME PROFILE – MODEL UC-24B
Glass
FULL-SCALE
T E M P L AT E S
The full-scale illustrations on the
following pages
enable you to understand some of the
unique situations
you may face as you
plan for the installation of the Undercounter units. Use
these illustrations as
templates.
Door Panel Profile
CL
25 mm
The full-scale illustration shows the door frame
profile for Model UC-24B.
25 mm
IMPORTANT NOTE: Rails and stiles must be a
minimum of 57 mm wide. The back sides of rails
and stiles that will be visible through the glass
door will need to be finished.
57 mm Rail / Stile
DOOR FRAME PROFILE
WINE SHELF WOOD FACING – MODELS UC-24B AND UC-24C
16 mm
Maximum Thickness
3 mm
38 mm
21 mm
2 mm
495 mm
9 mm
14 mm
FRONT VIEW
For Models UC-24B and UC-24C, use the full-scale
illustration above as a template if you choose to
replace the natural cherry wood facing with
wood more complementary to your design and
surrounding cabinetry.
70
SIDE VIEW
UNDERCOUNTER DOOR CLOSED AND 145˚ MAX OPENING
610 mm
CABINETRY
OPENING
587 mm
TO BACK OF
APPLIANCE
SUB-ZERO DOOR
19 mm
13
mm
*UNDERCOUNTER
UNIT MUST EXTEND
A MINIMUM 6 mm
BEYOND THE FRONT
SURFACE OF
ADJOINING
CABINETRY TO
ALLOW THE MAXIMUM
DOOR SWING
DOOR PANEL
6 mm*
3 mm
600 mm
DOOR PANEL
WIDTH
DOOR
PANEL
145˚*
The full-scale illustration shows what
considerations you need to make for the
installation of the Undercounter unit and how
the maximum door opening may interact
with adjacent cabinets and countertops.
SUB-ZERO
DOOR
71
SUB-ZERO, INC.
P O BOX 44130
MADISON, WI 53744 USA
SUBZERO.COM
7001871
2 / 2007
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement