Knürr Cable Management
Knürr Cable Management
Knürr Cable Management
Knürr Cable Management
Strong points
It must be ensured when laying
cables that every kind of mechanical
stress is avoided.
Bending load
The bending radii may never be
less than the values provided by
the cable manufacturer in the
respective data sheets. At points
that bend too much, the electrical
properties of the cable change and
reduce the transmission bandwidths
and ranges.
If manufacturer specifications are
not available, then the following
rule of thumb applies: With loose
cabling, at least 15 times the external
cable diameter and with fixed
cabling, at least 10 times the external
cable diameter.
MEC20064
Buckling load
The most extreme bending loads
can cause the cable to break.
MEC20086
MEC20074
MEC20058
Tensile load
This is only determined by the copper
cross-section of the conductor, as
all other materials are too soft. The
cable may not be stressed more
than 50N/mm2(Cu cross-section) as
otherwise the conductors are
stretched and the cross-section is
reduced. If higher “pulling” forces
are required, then cables with additional strain relief elements must be
used.
Compressive stress
Compressive stress is caused by
loads bearing down from above,
fixed clamping or sharp cable
kinking and must always be
avoided, as otherwise the “loose”
cable structure changes and the
electrical transmission properties
are impaired.
Torque strains (twisting)
These must never have an effect on
the cable, as they drive the cable
elements into one another and
therefore impair the transmission
properties.
MEC20084
LIG00021
Knürr Cable Management
Knürr Cable Management
Strong points
1
Different components for fiberglass and copper cables, especially
the fastening options using Velcro
strips and cable bundling using different colored strips, guarantee
transparent cable management,
which is the optimum starting situation for an intelligent expansion
of the network and for the highest
standard of service convenience.
2
With all cable management components, special attention has been
paid to ensuring that fixing is possible with Velcro strip cable ties.
Velcro cable ties not only guarantee a stress-free fixing of the
cables, they can also be released at
any time and re-used again and
again. Velcro cable ties are also
extremely helpful for the installation
engineer in providing pinch-free
cable bundling – and also because
they are so quick to apply.
3
Excess cable lengths are stored
separate from the patch fields, but
in a position that is always easy to
access. Copper cable excess can be
stored separate from fiber glass
excess within the Knürr rack systems:
the copper cables on the side and
the more sensitive fiberglass cables
in an excess drawer at the front.
4
Some true multi-talents appear on
closer examination of the individual
products. The cable routing multifunctional brace, for example, not
only provides the option of routing
cables horizontally and vertically
using Velcro ties or cable ties, but
rather also allows numerous components to be mounted with
screws and caged nuts. These
caged nuts can also be shifted with
room for play in a slot, so that every
mounting dimension can be
accommodated.
5
The prescribed radii are preset with
the radial limiter. These components
ensure that neither a reduction of
the transmission bandwidths and
ranges nor a cable break occur.
1 MEC20082
2 MEC20070
3 MEC20099
3 MEC20079
4 MEC20077
4 MEC20091
5 MEC20071
Knürr Cable Management
W
19” Cable Routing Board, 1 U
Type 1
MEC00110
Type 2
– For orderly cable routing
– For safe and secure cable routing of copper
and fiberglass cables
U
Model
Order no.
UP
483
H
D
1
Type 1
05.040.100.1
1 unit
483
2
Type 2
05.040.101.1
1 unit
483
1
Type 1
05.040.100.8
1 unit
483
2
Type 2
05.040.101.8
1 unit
■ Material/Finish
Type 1:
Front panel, sheet steel, 1.5 mm
Powder-coated, RAL 7035, light gray
Type 2:
Front panel: sheet steel 1.0 mm, powdercoated, RAL 7035 light gray
Fiber optic cable routing
panel 1 U
– For orderly cable routing
– For safe and secure cable routing of fiber
optic cables
– Optionally with cover panels to protect
the cables and as labeling option
MEC20014
■ Color
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .8:
RAL 7021 dark gray
Type 1
MEC20103
Type 2
MEC20104
MEC20081
■ External dimensions
Cable routing:
Type 1: 55 x 22 mm, plastic
Type 2: 95 x 32 mm, steel
■ Material/Finish
Sheet steel, 1.5 mm
Powder-coated texture, RAL 7035
MEC20105
■ Supply schedule
1 19” cable routing panel
■ Supply schedule
1 19” front panel
5 cable routers
■ How supplied
In units
■ Note
Please also order front panel mounting
material and cover.
Not suitable for rack widths 600 mm
and 700 mm (asymmetric)!
■ How supplied
Preassembled
■ Note
Please also order front panel mounting
material.
W
H
D
MEC20058
U
Model
Order no.
UP
483
1
Type 1
05.040.111.1
1 unit
W
483
1
Type 2
01.117.144.1
1 unit
483
483
1
Type 1
05.040.111.8
1 unit
483
1
Type 2
01.117.144.8
1 unit
H
D
U
Model
1
Cable routing panel 05.040.050.1
1 unit
Accessories: Cover
1 unit
MEC20102
– For orderly cable management in the
rack internal space
– With edge protector
– For orderly cable routing
– For safe and secure cable routing of copper
and fiberglass cables
■ Material/Finish
Front panel, sheet steel, 1.5 mm
Powder-coated texture, RAL 7035
Jumpering bracket, round steel, d = 5 mm,
zinc-passivated
■ Color
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .8:
RAL 7021 dark gray
■ Material
Sheet steel, 1.0 mm
CUD00021
■ Finish
Final digit of order number .1:
Powder-coated, RAL 7035, light gray
Final digit of order number .8:
Powder-coated texture, RAL 7021 dark
gray
■ Supply schedule
6 19” blanking panel cable ports
CUD00023
■ How supplied
Flat-packed kit
■ External dimensions
Cable routers (a x b):
1 U: 82 x 43 mm
2 U: 102 x 82 mm
MEC20076
■ Note
Please also order front panel mounting
material.
■ Supply schedule
1 front panel
5” cable routing boards
■ How supplied
Preassembled
■ Note
Please also order front panel mounting
material.
05.040.051.1
UP
19” Blanking Panel Cable
Port, threaded connection
19” Cable Routing Board,
flexible, 1 U
MEC20041
Order no.
CUD00022
W
H
U
For rack type
Order no.
483
44
D
1
Powder-coated
01.103.231.1
UP
6 units
483
88
2
Powder-coated
01.103.232.1
3 units
Knürr Cable Management
■ Finish
Zinc-passivated
Cable routing brace
■ Supply schedule
4 multifunctional braces
– For mounting on the Miracel/Smaract
basic rack and on the 19” extrusion
– For cable clamping using Velcro strips,
cable ties
– For orderly cable management in the
rack
– Two-sided installation
– For universal mounting option using
caged nuts (all dimensions can be
accommodated, as caged nuts are flexible)
MEC20091
Pos.2
Pos.1
■ Material
Sheet steel, 1.5 mm
WRack DRack d
Inst. position for rack type
Order no.
UP
600
1
Miracel
05.040.160.9
4 units
800
1
Miracel
05.040.161.9
4 units
900
1
Miracel
05.040.162.9
4 units
1000
1
Miracel
05.040.163.9
4 units
■ Supply schedule
4 cable routing braces
Mounting material
■ How supplied
In units
■ Note
If required, please also order Velcro
strip.
Pos.2
1100
1
Miracel
05.040.164.9
4 units
1200
1
Miracel
05.040.165.9
4 units
600
2
Miracel/Smaract
05.040.173.9
4 units
700
2
Miracel
800
2
Miracel
05.040.174.9
4 units
3
Miracel/Smaract/DPR
05.040.175.9
4 units
600 365 4
Miracel/Smaract
05.040.168.9
4 units
800 565 4
Miracel/Smaract
05.040.169.9
4 units
600 440 4
Miracel/Smaract
05.040.170.9
4 units
800 640 4
Miracel/Smaract
05.040.171.9
4 units
900 740 4
Miracel/Smaract
05.040.172.9
4 units
1000 740 4
Miracel/Smaract
05.040.172.9
4 units
Pos.1
Pos.3
MIR88001
WRack HRack DRack L
Model
for rack type
Order no.
UP
600 455
Pos. 1
Miracel
05.040.200.9
4 units
800 655
Pos. 1
Miracel
05.040.201.9
4 units
900 755
Pos. 1
Miracel
05.040.202.9
4 units
1000 855
Pos. 1
Miracel
05.040.203.9
4 units
600
534
Pos. 2
Miracel/Smaract
05.040.213.9
4 units
800
734
Pos. 2
Miracel
05.040.214.9
4 units
Pos. 3
Miracel/Smaract/DPR 05.040.215.9
4 units
Pos. 1
Miracel
4 units
468
1055
05.040.205.9
– For orderly cable management and
cable clamping
– Can be expanded
■ Material/Finish
Base cover: Sheet steel, powder-coated
texture
RAL 7035
Foam: Polyethylene, anthracite
■ Supply schedule
2 end plates with foam
3 plates with foam on both sides
Mounting material
Multifunctional brace
– For routing cables with cable ties
– For universal mounting options
– Holes for mounting caged nuts
– Distance between two multifunctional
braces can be variably selected using T-slot
– Installation on the extrusions of the rack
frame or on the 19” extrusions, diagonal
and lateral
■ Installation positions
1 on the basic frame on the depth
2 on the basic frame on the width
3 on the 19” extrusions on the width
4 on the 19” extrusions on the depth
■ Material
Sheet steel, 1.5 mm
■ Finish
Zinc-passivated
4 units
Cascading
MEC20045
MIR00089
Pos.3
Pos.4
MIR88003
■ Finish
Zinc-passivated
MEC20078
■ How supplied
Flat-packed kit
■ How supplied
Flat-packed kit
MEC20074
W
H
D
Order no.
UP
05.040.088.9
1 set
Knürr Cable Management
Cable Tray
Assembly Crossbar
– For orderly cable management in the
Miracel rack
– Cable fixing possible using Velcro strips
or cable ties
– Combination possible as L, U or T unit
Type 1
– For cable management with Velcro
strips
– Universal mounting option for installation
accessories, socket strips, telecommunication installation units, mounting
panels, etc.
– For side and cross installation
MEC20136
■ Material/Finish
Sheet steel 1.5 mm, zinc passivated,
powder-coated
■ Color
.1: RAL 7035 light gray
.8: RAL 7021 dark gray
MEC20088
■ Material/Finish
Sheet steel 1.5 mm,
powder-coated texture, RAL 7035
Type 1
MEC20120
■ Supply schedule
1 assembly crossbar
■ Dimensions
L 150 x W 28 mm
■ How supplied
In units
Type 2
■ Supply schedule
1 cable tray
Mounting material
■ Note
Please also order the appropriate
mounting material.
MEC20137
■ How supplied
Flat-packed kit
■ Note
If required, please also order Velcro strip.
MEC20067
Type 2
MEC20121
W
H
D
U
Model
Order no.
UP
41
For rack type Miracel
05.040.021.1
1 set
46
For rack type Miracel
05.040.022.1
1 set
41
For rack type Miracel
05.040.021.8
1 set
46
For rack type Miracel
05.040.022.8
1 set
C-Extrusion Rail
– For cable clamping using U-clamps or
cable clamping bars
– Cable clamping closer to access (type 1)
– Suitable for use in conjunction with top
cover with cable entry
MIR00096
MIR00094
W/d H D U w1 w2
X
Type Model
Order no.
UP
19”
1 482 442.6 81.5 1
Pos. 2: Miracel/Smaract 05.040.018.1
1 unit
19”
1
Pos. 2: DoubleProRack 05.040.019.1
1 unit
2
■ Material/Finish
Sheet steel, 1.5 mm, zinc-passivated
Pos.1
Pos.2
■ Supply schedule
1 C extrusion rail
Mounting material
Cable Clamping Bar
■ How supplied
Flat-packed kit
– For clipping to the C-shaped runner
■ Note
Please also order U-clamps, cable clamping bars or threaded plates.
■ Material
Polyamide, black
MEC00114
■ Supply schedule
1 set of 10 cable clamping bars
■ How supplied
Flat-packed kit
W
MIR88002
W
L
Model
Order no.
UP
600
H
D
482.5
Pos. 1: Miracel/Smaract
05.040.080.0
1 unit
800
682.5
Pos. 1: Miracel
05.040.082.0
1 unit
19
508
Pos. 2: Miracel/Smaract/
01.110.719.9
1 unit
DoubleProRack
H
D
U
d L
Model
Dimensions in mm: W
H
D
h
d
L
Conversion:
=
=
=
=
=
=
Order no.
UP
01.130.869.9
10 units
Width
U = standard height unit
Height
1 U = 44.45 mm
Depth
UP = unit of packaging
installation height kg = weight
useful depth
length
= Express item
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Knürr Cable Management
C-Extrusion Rail
Type 1
Type 2
MEC00113
U-Clamp
– For cable clamping using U-clamps or
cable clamping bars
– Space-saving installation between the
extrusions of the basic rack
– Two-sided installation
■ Material
Sheet steel, 1.5 mm, zinc-passivated
– For strain relief and individual routing of
cables and lines
– Clamping range, 8-64 mm
■ Material
Steel/plastic
MIR00096
■ Supply schedule
25 U-clamps
25 clamping saddles
■ Finish
Zinc-passivated
■ How supplied
Flat-packed kit
■ Supply schedule
4 extrusion rails
Mounting material
Pos.1
Pos.3
Pos.2
■ How supplied
Flat-packed kit
ELM00086
■ Note
Please also order U-clamps, cable
clamping bars or threaded plates.
W
H
D
U
d L
MIR88004
WRack DRack WRack
600
Inst. position
1
800
1
For rack type
Miracel
Miracel
Order no.
05.040.180.9
05.040.181.9
UP
4 units
4 units
900
1
Miracel
05.040.182.9
4 units
1000
1
Miracel
05.040.183.9
4 units
1200
1
Miracel
05.040.185.9
4 units
3
Miracel/Smaract
05.040.195.9
4 units
800
2
Miracel/Smaract
05.040.194.9
4 units
600
2
Miracel/Smaract
05.040.193.9
4 units
Clamping range Order no.
UP
8-12 mm
05.040.150.9
1 unit
12-16 mm
05.040.151.9
1 unit
16-22 mm
05.040.152.9
1 unit
22-28 mm
05.040.154.9
1 unit
34-40 mm
05.040.155.9
1 unit
46-52 mm
05.040.157.9
1 unit
58-64 mm
05.040.159.9
1 unit
M5 Threaded Plate
– For use in conjunction with C extrusion
rails
■ Material/Finish
Flat rolled steel, 4.0 mm, zinc-passivated
MEC20051
■ Supply schedule
20 threaded plates
Top-mounting for cable tray
■ How supplied
Flat-packed kit
– Fixing cable trays with C extrusion rails
– Any position possible
■ Material/Finish
C extrusion rail: Sheet steel, zinc-passivated
Mounting bracket: Sheet steel, powdered
RAL 7021
MIR20198
MEC20069
■ Supply schedule
2 C extrusion rails
4 mounting bracket
Mounting material
W
H
D
L
Order no.
UP
05.040.077.9
1 set
■ How supplied
Flat-packed kit
■ Note
Please also order U-clamps, cable clamping
bars or threaded plates.
MEC20034
W
H
DRack
Order no.
UP
800
05.040.072.8
1 set
900
05.040.073.8
1 set
1000
05.040.074.8
1 set
1200
05.040.076.8
1 set
19” Cable Tray
- For orderly cable management in front of
the 19” front
- Mounting on front panels possible
- Cable fixing possible using Velcro strips
MEC20049
■ Material/Finish
Sheet steel, 1.5 mm
Powder-coated texture, RAL 7035
■ Supply schedule
1 cable tray
Knürr Cable Management
■ How supplied
In units
Radial Limit, 1 U
■ Note
Please also order front panel mounting
material and Velcro strip.
MEC20132
MEC20063
W
H
483
– For diverting the cables from the patch
area vertically
– The cables can be fixed with Velcro strips
– Side use in conjunction with the cable
duct is possible
D
U
100
1
Model
Order no.
UP
05.040.055.1
1 unit
■ Material/Finish
Sheet steel, 1.5mm,
powder-coated texture, RAL 7035
■ Supply schedule
1 radial limit
1 Mounting panel
Mounting material
Cable tray between the
racks
■ How supplied
Flat-packed kit
– For orderly cable management between
linked racks
– Fixing possible using Velcro strips
■ Material/Finish
Sheet steel, 1.5mm
Powder-coated texture, RAL 7035
MEC20042
MEC20143
■ Supply schedule
1 cable tray
Mounting material
W
H
85
■ How supplied
Flat-packed kit
D
U
32
1
Model
Order no.
UP
05.040.091.1
1 set
■ Note
Please also order Velcro strip
CDuct, Side
MEC20119
W
H
265
D
U
Model
60
Order no.
UP
05.040.058.1
1 unit
– For orderly cable management
– For use in conjunction with the front
panel, swivel
– Cable rerouting with radial limiter, 1 U
(optional)
MEC20135
■ Material/Finish
Sheet steel, 1.5mm
Powder-coated texture, RAL 7035
Radial limit
■ Supply schedule
1 cable duct
Mounting material
– Various mounting options available:
– on the basic rack for cable clamping
– on the 19” extrusion for cable routing
and diverting
– For use in conjunction with C extrusion
rails (also order threaded plates!)
MEC20090
■ Material/Finish
Sheet steel, 1.5mm, zinc-passivated
■ Supply schedule
1 radial limit
Mounting material
■ How supplied
Flat-packed kit
MEC20151
W
100
H
D
U
130
41
Model
Order no.
UP
05.040.023.1
1 set
■ How supplied
Flat-packed kit
MEC20071
W
290
H
D
87
L
Order no.
UP
05.040.090.0
1 set
Dimensions in mm: W
H
D
h
d
L
Conversion:
=
=
=
=
=
=
Width
U = standard height unit
Height
1 U = 44.45 mm
Depth
UP = unit of packaging
installation height kg = weight
useful depth
length
= Express item
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Knürr Cable Management
Excess Copper Cable
Storage
Universal Jumpering
Bracket
– For storing excess copper cable lengths
(or fiber optic cables)
– For orderly cable management in the
Miracel rack
– Can be expanded
MEC20052
■ Material/Finish
Sheet steel, 1.5 mm, zinc-passivated
– Can be used for extrusion spacing (from
front), 123 mm and 73 mm
– For orderly cable management
– Open version, no threading
– Mounting on the external side of the 19”
extrusion
– Any installation position selectable
MEC20038
■ Material
Round steel, d = 6 mm
■ Supply schedule
1 excess cable holder
Mounting material
■ Finish
Zinc-passivated
■ How supplied
Flat-packed kit
■ Supply schedule
4 jumpering brackets
MEC20079
W
H
D
U
Model
Order no.
UP
For rack type Miracel
05.040.044.0
1 set
■ How supplied
Flat-packed kit
MEC20072
■ Note
Please also order the appropriate
mounting material.
Fiber Optic 19” Excess
Cable Drawer, 1 U
– For storing excess fiber optic cable lengths
– Pull-out
– Cable fixing possible with Velcro strips
■ Material/Finish
Sheet steel, 1.5 mm
Powder-coated texture, RAL 7035
MEC20047
MEC20106
WRack
For rack type
Order no.
UP
From 800
Miracel
05.040.220.9
4 units
■ Supply schedule
1 main unit
1 drawer
Square Jumpering Bracket
■ How supplied
Flat-packed kit
■ Note
Please also order front panel mounting
material and Velcro strip.
– For orderly cable management
– Open version, no threading
– Mounting on the external side of the
19” extrusion
– Any installation position selectable
– For large cable volumes
MEC20099
MEC20039
W
H
D
483
44
350
Model
Order no.
UP
05.040.047.1
1 set
■ Material
Round steel, d = 6 mm
■ Finish
Zinc-passivated
Excess Fiber Optic Cable
Storage
– For orderly fiber optic cable management
in the Miracel rack (from W 800 mm)
– For storing excess cable lengths
■ Supply schedule
4 square jumpering brackets
■ How supplied
Flat-packed kit
MEC20107
Type 1
MEC20116
Type 2
■ Material/Finish
Base cover: powder-coated
texture, RAL 7035
Cable routing head: Polyamide, black
MEC20044
■ Note
Please also order the appropriate
mounting material.
■ Supply schedule
1 base cover
1 cable routing head
Mounting material
■ How supplied
Flat-packed kit
MEC20146
W
H
D
U
2
Model
WRack
Type
For rack type
Order no.
UP
From 800
Type 1
Miracel
05.040.221.9
4 units
Order no.
UP
From 700
Type 2
Miracel
05.040.222.9
4 units
05.040.041.1
1 set
600
Type 2
Smaract
05.040.222.9
4 units
Knürr Cable Management
Quick-Strip Velcro strip for
T-slot mounting without tools
–
–
–
–
–
MEC20185
Quick fixing without tools
For bundling cables
Can be released and used again
For orderly cable management
For fixing into T-slots at any position
■ Material
Polyethylene and Nylon
F.R.T., UL-94 HB
MEC20108
■ Color
Black
A
B
b
Model
Order no.
82
72
43
33
Fig. 1
05.040.231.0
10 units
■ Supply schedule
10 Quick-Strip Velcro strips
222
212
30
20
Fig. 3
05.040.232.0
10 units
102
92
82
72
Fig. 2
05.040.233.0
10 units
a
UP
■ How supplied
Flat-packed kit
W
H
D
U
d L
For rack type
Order no.
UP
Miracel
00.218.506.0
1 set
Quick-Clamp plastic
jumpering bracket for T-slot
mounting without tools
–
–
–
–
Square Jumpering Bracket
– For orderly cable management
– Open version, no threading
– Mounting on the external lateral T-slot
of the 19” extrusion
– Any installation position selectable
ELM00117
Quick fixing without tools
For orderly cable management
Open version, no threading
For fixing on T-slots at any position
■ Finish
Zinc-passivated
■ Supply schedule
4 jumpering brackets
■ Material
Nylon
F.R.T., UL-94 HB
■ How supplied
Flat-packed kit
■ Color
Black
■ Supply schedule
10 plastic jumpering brackets
ELM00106
■ How supplied
Flat-packed kit
W
H
D
U
d L
■ Material
Round steel, d = 5 mm
For rack type
Order no.
UP
Miracel
00.218.505.0
1 set
■ Note
Please also order the appropriate
mounting material.
For rack type
Order no.
UP
DoubleProRack
05.040.226.9
4 units
Jumpering Bracket
2
1
3
MEC20035
– For flexible and orderly cable routing
– Any installation place and position
selectable
– Open version, no threading
■ Material/Finish
Round steel, d = 5 mm
MIR00564
■ Finish
Zinc-passivated
■ Material
Round steel, d = 5 mm
■ Supply schedule
4 jumpering brackets
■ Finish
Zinc-passivated
■ How supplied
Flat-packed kit
■ Supply schedule
10 jumpering brackets
Mounting material
■ Note
Please also order the appropriate
mounting material.
■ How supplied
Flat-packed kit
MEC20065
– For orderly cable management
– Open version, no threading
Jumpering Bracket, Flexible
MEC00122
Model
no.
UP
Order
Knürr Cable Management
Jumper Tiebar
Jumpering Bracket, Vertical
– Ideal for vertical routing and cable strain
relief
– Open version, no threading
– Mounting on the external lateral T-slot
of the 19” extrusion
– Any installation position selectable
– From rack width 600 mm
ELM00028
– For orderly cable management
– Open version, no threading
– Mounting on the external side of the
19” extrusion and on the side on the
rack T-slot
– Any installation position selectable
– For large cable volumes
MIR00566
■ Material/Finish
Round steel, d = 5 mm, zinc-passivated
■ Material
Round steel, d = 6 mm
■ Supply schedule
2 jumper tiebars
■ Finish
Zinc-passivated
■ How supplied
Flat-packed kit
■ Supply schedule
4 vertical jumpering brackets
■ Note
Please also order the appropriate
mounting material.
■ How supplied
Flat-packed kit
■ Note
Please also order the appropriate
mounting material.
MEC00123
ELM00029
W
H
D
U
d L
Model
Order no.
UP
01.117.033.7
2 units
Model
Order no.
UP
218x60
05.040.223.9
4 units
Cable Duct
Jumpering Bracket, Square
– For orderly cable management
– Open version, no threading
– Mounting on the external lateral T-slot
of the 19” extrusion
– Any installation position selectable
– From rack width 800 mm
MIR00183
– Ideal for orderly and covered cable
management of jumper cables
■ Material
Hard PVC
ELM00004
■ Finish
Stone gray, RAL 7030
■ Supply schedule
1 jumper cable duct with cover
Mounting material
■ Finish
Zinc-passivated, Zn 10c, white
■ Supply schedule
4 vertical jumpering brackets
■ How supplied
Flat-packed kit
ELM00052
W
H
D
U
d L
Model
2000
Order no.
UP
01.117.098.3
1 units
ELM00057
WRack
Model
Order no.
UP
From 800
86x86
05.040.224.9
4 units
Fiber Optic Cable Router
LIG00068
Dimensions in mm: W
H
D
h
d
L
Conversion:
=
=
=
=
=
=
■ Material
PA UL (94-VO)
Width
U = standard height unit
Height
1 U = 44.45 mm
Depth
UP = unit of packaging
installation height kg = weight
useful depth
length
= Express item
1 mm = 0.03937 inch
1 kg = 2.2046 pound
– For safe and orderly cable management of
fiber optic cables
– With step-index extrusion of the slots to
provide strain relief of the fiber optic
cables
– Mounting on the external side of the 19”
extrusion
LIG00021
■ Supply schedule
1 pair of fiber optic cable routers
Mounting material
Knürr Cable Management
■ How supplied
Flat-packed kit
W
H
D
U
d L
■ Supply schedule
1-meter or 25-meter Velcro strip
Model
Order no.
UP
01.117.099.1
1 pair
■ How supplied
By the meter
MEC20147
W
Cable Routing Ring
– For orderly cable management
– Open version, no threading
– Mounting on the T-slots of the vertical
extrusions
– Any installation position selectable
Model
Order no.
16
H
D
L
1000
Black
05.040.060.9
16
1000
Blue
05.040.061.9
1 meter
16
25000
Black
05.040.065.9
25 meters
16
25000
Blue
05.040.066.9
25 meters
■ Material/Finish
PA 6, GF 15, black, UL 94-HB
ELM00025
UP
1 meter
Velcro Strip with Plastic
Eyelet
■ Supply schedule
5 cable routing rings
Mounting material
– For mounting non-standard components
– For bundling cables
■ How supplied
Flat-packed kit
■ Material/Color
Polypropylene/Polyamide, black
MEC20025
■ Supply schedule
20 Velcro strips
W
H
D
U
d L
Model
Order no.
UP
54 x 118 mm
01.312.207.9
5 units
■ How supplied
Flat-packed kit
W
H
D
16
L
Model
300
Order no.
UP
01.240.550.9
1 set
Cable Routing Set
Cable Band Clip
– For orderly cable management
- Dimensions:
Outside 61 mm x 42.5 mm,
inside 52 mm x 23 mm
– For orderly cable management
– For fixing cable harnesses and cables
with large cross section
– Quick and easy mounting
– For clipping into T-slots at any position
– With detachable lock
MEC20158
■ Material/Finish
Cable holder: PPO,
sim. RAL 7035 light gray
Soft rubber extrusion: EPDM,
sim. RAL 7021 dark gray
ELM00049
■ Material
PA 6.6, black, UL 94-V0
■ Supply schedule
10 cable routers
■ How supplied
Flat-packed kit
■ Supply schedule
20
ELM00050
■ How supplied
Flat-packed kit
■ Note
Please also order the appropriate
mounting material.
W
W
H
D
U
d L
Model
Order no.
UP
Threaded
05.040.113.9
10 units
05.040.112.9
10 units
For cut-out 9.5 x 9.5 mm Plug-in
H
D
U
d L
Model
Order no.
UP
01.240.548.9
20 units
Velcro strip (by the meter)
– For stress-free mounting and bundling of
copper and fiber optic cables
– Velcro strip can be cut to any length
required
MEC20048
■ Material/Color
Black: One Wrap Fastener
F.R.T., UL 94-V2
Blue: One Wrap Fastener
Dimensions in mm: W
H
D
h
d
L
Conversion:
=
=
=
=
=
=
Width
U = standard height unit
Height
1 U = 44.45 mm
Depth
UP = unit of packaging
installation height kg = weight
useful depth
length
= Express item
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Knürr Cable Management
Cable Clamping, Swing
Frame
Cable Clamping Frame
– For orderly cable management
– Open version, no threading
– Cross-section for cable routing, variable
with removable routing ribs
– Can be expanded by adding on further
cable clamping frames
– Optional mounting: lengthwise or
across the width
MEC20017
– Absolutely recommended when using
swing frame
– For cable strain relief
– For relief on plug-type connections
– Prevents damage to the cable braided
shielding
MIR00086
■ Supply schedule
2 mounting bracket
1 extrusion rail
Mounting material
■ Material
Polypropylene, black
■ Supply schedule
1 cable clamping frame
Mounting material
■ How supplied
Flat-packed kit
ELM00024
W
H
D
U
d L
Model
MIR00182
Order no.
UP
01.113.153.9
1 units
W
H
D
U
d L
Model
Cable Cantilever
–
–
–
–
TEL00034
■ Supply schedule
1 cable cantilever
Mounting material
H
D
U
d WxL
Type
Order no.
UP
2-piece
05.040.096.0
1 unit
– For 19” cable routing panel, 2 HU
– For strain relief of cables and plug-type
connections with cable ties
■ Material
Sheet steel, 1.5 mm
■ Finish
Zinc-passivated, Zn 10c, white
■ Supply schedule
1 earthing bracket
Mounting material
CUD00024
W
H
D
U
d L
Model
■ Supply schedule
1 cable roller
W
Cable Clamping Bracket /
Earthing Bracket
CUD00025
For 19” racks and enclosures
Reduces the cable load on slot-in
Orderly cabling
Prevents cable-sagging
TEL00051
■ How supplied
Flat-packed kit
W
1 set
■ Material
Sheet steel, 1.5 mm
■ Material/Finish
Sheet steel, 1.5 mm, zinc-passivated
MEC88005
UP
01.113.203.1
Cable Roller
– For easy mounting in rack/on the shelf;
quick connecting to and disconnecting
from shelf or rack with a spring clip
– Guarantees defined and kink-free cable
management
– Minimum space requirement behind
the pushed-in shelves, 40 mm
MEC20154
Order no.
Order no.
UP
01.117.035.7
1 units
H
D
U
d L
Model
Order no.
UP
05.043.327.9
1 units
Knürr System Accessories
19” shelf, fixed
19” shelf, part pull-out
– Integrated fixing holes front and rear for
handle or hinged cable routing
– With perforation to optimize air supply
■ Material/Finish
Sheet steel 1.0 mm, zinc-passivated,
powder-coated texture
MEC00451
– Integrated fixing holes front and rear for
handle or hinged cable routing
– With perforation to optimize air supply
– Locking in pulled-out position (friction
lock); easy conversion from form lock to
friction lock with stop spring
– Quick separator for removing and disconnecting the shelf without tools
MEC00452
■ Color
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .8:
RAL 7021 dark gray
■ Material/Finish
Sheet steel 1.0 mm, zinc-passivated,
powder-coated texture
■ Color
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .8:
RAL 7021 dark gray
■ Load rating
500 N static per item
■ Supply schedule
2 mounting rails, incl. mounting bracket
1 shelf board
1 extension board (from L = 600)
Mounting material
■ Load rating
500 N static per item
■ Supply schedule
1 pair of telescopic slides
1 shelf board
1 extension board (from L = 600)
Mounting material
■ How supplied
Flat-packed kit
MEC20018
MEC20019
WRack HRack DRack d
wxl
For rack type
■ How supplied
Flat-packed kit
Order no.
UP
600 365 430 x 300 Miracel/Smaract LAN
01.102.001.1
1 unit
600 440 430 x 300 Miracel/Smaract 19”
01.102.002.1
1 unit
800 565 430 x 500 Miracel/Smaract LAN
01.102.003.1
1 unit
800 565 430 x 500 Miracel/Smaract LAN
01.102.003.8
1 unit
Order no.
UP
800 640 430 x 600 Miracel/Smaract 19”
01.102.004.1
1 unit
600 365 430 x 300 Miracel/Smaract LAN
01.102.010.1
1 unit
800 640 430 x 600 Miracel/Smaract 19”
01.102.004.8
1 unit
600 440 430 x 300 Miracel/Smaract 19”
01.102.010.1
1 unit
900 665 430 x 600 Miracel/Smaract LAN
01.102.004.1
1 unit
800 565 430 x 500 Miracel/Smaract LAN
01.102.011.1
1 unit
900 665 430 x 600 Miracel/Smaract LAN
01.102.004.8
1 unit
800 565 430 x 500 Miracel/Smaract LAN
01.102.011.8
1 unit
900 740 430 X 600 Miracel/Smaract 19” server 01.102.005.1
1 unit
800 640 430 x 500 Miracel/Smaract 19”
01.102.011.1
1 unit
900 740 430 X 600 Miracel/Smaract 19” server 01.102.005.8
1 unit
800 640 430 x 500 Miracel/Smaract 19”
01.102.011.8
1 unit
WRack HRack DRack d
wxl
For rack type
1000 740 430 x 600 Miracel 19” server
01.102.005.1
1 unit
900 665 430 x 500 Miracel/Smaract LAN
01.102.011.1
1 unit
1000 740 430 x 600 Miracel 19” server
01.102.005.8
1 unit
900 665 430 x 500 Miracel/Smaract LAN
01.102.011.8
1 unit
900 740 430 x 600 Miracel/Smaract 19” server 01.102.012.1
1 unit
900 740 430 x 600 Miracel/Smaract 19” server 01.102.012.8
1 unit
600
600 530 515 x 500 Miracel LW 535
01.102.200.1
1 unit
700
600 530 615 x 500 Miracel LW 635
01.102.201.1
1 unit
1000 740 430 x 600 Miracel 19” server
01.102.012.1
1 unit
800
600 530 715 x 500 Miracel LW 735
01.102.202.1
1 unit
1000 740 430 x 600 Miracel 19” server
01.102.012.8
1 unit
600
800 730 515 x 700 Miracel LW 535
01.102.208.1
1 unit
700
800 730 615 x 700 Miracel LW 635
01.102.209.1
1 unit
600
600 530 515 x 500 Miracel LW 535
01.102.170.1
1 unit
800
800 730 715 x 700 Miracel LW 735
01.102.210.1
1 unit
700
600 530 615 x 500 Miracel LW 635
01.102.171.1
1 unit
600
900 830 515 x 800 Miracel LW 535
01.102.212.1
1 unit
800
600 530 715 x 500 Miracel LW 735
01.102.172.1
1 unit
800
900 830 715 x 800 Miracel LW 735
01.102.214.1
1 unit
600
800/ 730 515 x 600 Miracel LW 535
01.102.178.1
1 unit
01.102.179.1
1 unit
01.102.180.1
1 unit
900
600
600 535 515 x 500 Smaract LW 535
01.102.252.1
1 unit
600
800 735 515 x 700 Smaract LW 535
01.102.254.1
1 unit
600
900 835 515 x 800 Smaract LW 535
01.102.255.1
1 unit
700
800/ 730 615 x 600 Miracel LW 635
900
800
800/ 730 715 x 600 Miracel LW 735
900
600 435 430 x 300 DoubleProRack with door 01.102.002.1
1 unit
800 635 430 x 600 DoubleProRack with door 01.102.004.1
1 unit
600 435 430 x 300 DoubleProRack with door 01.102.010.1
1 unit
800 635 430 x 600 DoubleProRack with door 01.102.004.8
1 unit
800 635 430 x 500 DoubleProRack with door 01.102.011.1
1 unit
800 635 430 x 500 DoubleProRack with door 01.102.011.8
1 unit
500 460 430 x 300 DoubleProRack no door
01.102.002.1
1 unit
600 560 430 x 500 DoubleProRack no door
01.102.003.1
1 unit
500 460 430 x 300 DoubleProRack no door
01.102.010.1
1 unit
600 560 430 x 500 DoubleProRack no door
01.102.003.8
1 unit
600 560 430 x 500 DoubleProRack no door
01.102.011.1
1 unit
700 660 430 x 600 DoubleProRack no door
01.102.004.1
1 unit
600 560 430 x 500 DoubleProRack no door
01.102.011.8
1 unit
700 660 430 x 600 DoubleProRack no door
01.102.004.8
1 unit
700 660 430 x 500 DoubleProRack no door
01.102.011.1
1 unit
700 660 430 x 500 DoubleProRack no door
01.102.011.8
1 unit
600 385 430 x 300 ConAct
01.102.010.1
1 unit
500 285 430 x 200 ConAct
01.102.000.1
1 unit
600 385 430 x 300 ConAct
01.102.001.1
1 unit
Knürr System Accessories
WRack HRack
19” Shelf
Full pull-out
– Integrated fixing holes front and rear for
handle or hinged cable routing
– With perforation to optimize air supply
– Locking in pulled-out position (friction
lock); easy conversion with stop spring
– Quick separator for removing and disconnecting the shelf without tools
MEC00462
■ Load rating
500 N static per item
U
d
wxl
WRack HRack
U
d wxl
For rack type
Order no.
1 unit
565 467 x 460 Miracel/Smaract LAN 01.131.473.8
1 unit
800
640 467 x 460 Miracel/Smaract 19” 01.131.475.1
1 unit
900
665 467 x 560 Miracel/Smaract LAN 01.131.476.1
1 unit
900
740 467 x 560 Miracel/Smaract
01.131.474.1
1 unit
01.131.474.8
1 unit
900
740 467 x 560 Miracel/Smaract
19” Server
1000
740 467 x 560 Miracel 19” server
01.131.474.1
1 unit
1000
740 467 x 560 Miracel 19” server
01.131.474.8
1 unit
600
800
730 534 x 536 Miracel LW 535
01.131.477.1
1 unit
800
800
730 734 x 536 Miracel LW 735
01.131.479.1
1 unit
600
900
830 534 x 536 Miracel LW 535
01.131.481.1
1 unit
800
900
830 734 x 536 Miracel LW 735
01.131.483.1
1 unit
19” Heavy-Duty Shelf
Full pull-out
– With perforation to optimize air supply
– Locking in pushed-in and fully pulled out
position
– Easy mounting with patented quick
mounting system
– Application as server or battery bottom
cover
UP
600 365
430 x 300 Miracel/Smaract LAN 01.102.160.1
1 unit
600 440
430 x 300 Miracel/Smaract 19” 01.102.160.1
1 unit
800 565
430 x 500 Miracel/Smaract LAN 01.102.161.1
1 unit
800 640
430 x 500 Miracel/Smaract 19” 01.102.161.1
1 unit
900 665
430 x 500 Miracel/Smaract LAN 01.102.161.1
1 unit
900 740
430 x 600 Miracel/Smaract
01.102.162.1
1 unit
01.102.162.1
1 unit
MEC20022
■ Material/Finish
Sheet steel, 1.5 mm, powder-coated
texture
■ Color
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .8:
RAL 7021 dark gray
19” Server
1000 740
430 x 600 Miracel 19” server
UP
800
■ How supplied
Flat-packed kit
DRack
Order no.
565 467 x 460 Miracel/Smaract LAN 01.131.473.1
■ Supply schedule
1 pair of telescopic slides
1 shelf board
1 extension board (from L = 600)
Mounting material
MEC20xxx
For rack type
800
19” Server
■ Material/Finish
Sheet steel 1.0 mm, zinc-passivated,
powder-coated texture
■ Color
RAL 7035 light gray
DRack
■ Load rating
1200 N static
19” Heavy-Duty Shelf
Fixed
■ Supply schedule
1 pair of telescopic slides
1 shelf board
Mounting material
MEC20113
– Surface area with perforation
– Application as server or battery bottom
cover
MEC00120
■ Material/Finish
Sheet steel 1.5 mm, zinc-passivated,
powder-coated texture
■ How supplied
Flat-packed kit
WRack HRack
800
■ Color
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .8:
RAL 7021 dark gray
■ Load rating
1000 N static for CW installation
1500 N static for 19” installation
MEC20117
U
d wxl
For rack type
Order no.
UP
565 412 x 560 Miracel/Smaract LAN 01.102.031.1
1 unit
800
565 412 x 560 Miracel/Smaract LAN 01.102.031.8
1 unit
800
640 412 x 560 Miracel/Smaract 19” 01.102.031.1
1 unit
800
640 412 x 560 Miracel/Smaract 19” 01.102.031.8
1 unit
900
665 412 x 660 Miracel/Smaract LAN 01.102.032.1
1 unit
900
665 412 x 660 Miracel/Smaract LAN 01.102.032.8
1 unit
900
740 412 x 660 Miracel/Smaract
01.102.032.1
1 unit
01.102.032.8
1 unit
19” Server
900
■ Supply schedule
1 shelf, fixed, screwable
2 mounting braces
Mounting material
■ How supplied
Flat-packed kit
DRack
740 412 x 660 Miracel/Smaract
19” Server
1000
740 412 x 660 Miracel 19” server
01.102.032.1
1 unit
1000
740 412 x 660 Miracel 19” server
01.102.032.8
1 unit
600
800
730 478 x 560 Miracel LW 535
01.102.034.1
1 unit
800
800
730 678 x 560 Miracel LW 735
01.102.037.1
1 unit
600
900
830 478 x 660 Miracel LW 535
01.102.035.1
1 unit
800
900
830 678 x 660 Miracel LW 735
01.102.038.1
1 unit
600
800
735 478 x 560 Smaract LW 535
01.102.034.1
1 unit
600
900
835 478 x 660 Smaract LW 535
01.102.035.1
1 unit
Knürr System Accessories
19” Quick-Fix Shelf
Assembly without tools
– Quick and easy mounting without tools
by hanging in 19” cut-outs
– Quick and easy fixing (one click) and
removing (quarter turn) without tools
– Suitable for all racks and enclosures with
19” mounting hole extrusions (9.0 x 9.0
square holes)
– Depth-variable for use with different
slot-in depths and special dimensions
– With perforation to optimize air supply
SUN20007
■ Material
Sheet steel, 1.0 mm
Cable Cantilever
– Swing-out from the rear, therefore free
access to the rear side (only 3-piece)
– For easy mounting in rack/on the shelf;
quick connecting to and disconnecting
from shelf or rack with a spring clip
– Guarantees defined and kink-free cable
management
– Minimum space requirement behind the
pushed-in shelves, 40 mm
MEC20154
■ Material/Finish
Sheet steel, 1.5 mm, zinc-passivated
MEC88005
■ Supply schedule
1 cable cantilever
Mounting material
■ Finish
Final digit of order number .1:
Powder-coated texture, RAL 7035,
light gray
Final digit of order number .8:
Powder-coated texture, RAL 7021
dark gray
■ Load rating
700 N static with even load distribution
■ How supplied
Flat-packed kit
W
H
D
U
d wxl
Type
Order no.
UP
2-piece
05.040.096.0
1 unit
■ Supply schedule
19” Quick-Fix Shelf Mounting Material
■ How supplied
Flat-packed kit
■ Note
Cannot be used for 19” t-slot extrusions!
W
H
d
wxl
Order no.
UP
600
D
U
365 - 500
430 x 300
01.102.071.X
1 unit
800
565 - 740
430 x 500
01.102.072.X
1 unit
Handle
- Suitable for shelves and heavy-duty shelves
– With internal thread, M5
■ Material
Die-cast aluminum consoles
Handle extrusions of extruded aluminum
Cap made of ABS UL 94 HB
MEC20138
■ Finish:
Handle, powder-coated, gray-blue,
RAL 5008/Cap, light gray,
RAL7035
■ Supply schedule
2 handles
MEC20111
W
H
D
U
d wxl
For rack type
Order no.
UP
00.050.503.1
1 set
Dimensions in mm: W
H
D
h
d
L
CW
Conversion:
1 mm
=
=
=
=
=
=
=
=
Width
U
Height
Depth
UP
installation height kg
useful depth
length
Clear width
0.03937 inch
1 kg
= standard height unit
1 U = 44.45 mm
= unit of packaging
= weight
= Express item
= 2.2046 pound
Knürr System Accessories
W
19” Shelf, 2 U
Fixed
– For installation in racks with fixed 19”
installation on the front
– Quick and easy mounting on 19” extrusions
– Also for swing frame in the 19” rack and
19” enclosure
MIR00373
■ Finish/Color
Powder-coated texture, RAL 7035
light gray
H
D
wxl
For rack type
Order no.
UP
482.6 88.1 600/800/900/1000 442 x 480 Miracel/Smaract 01.113.411.1
1 unit
482.6 88.1 500/600/800
442 x 280 DoubleProRack 01.113.409.1
1 unit
482.6 88.1 500/600/800
442 x 380 DoubleProRack 01.113.410.1
1 unit
482.6 88.1 600/800
442 x 480 DoubleProRack 01.113.411.1
1 unit
482.6 88.1 400/500/600
442 x 280 ConAct
01.113.409.1
1 unit
482.6 88.1 500/600
442 x 380 ConAct
01.113.410.1
1 unit
482.6 88.1 600
442 x 480 ConAct
01.113.411.1
1 unit
■ Material
Sheet steel, 1.5 mm
■ Load rating
200 N static
19” Drawer
Installation on the front
■ Supply schedule
1 shelf, fixed
Mounting material
– For installation on the front
19” extrusions
– For storing service documents
– Quick and easy mounting
■ How supplied
Flat-packed kit
SCH00058
■ Material/Finish
Drawer, sheet steel 1.0 mm,
powder-coated texture
Telescopic slides, sendzimir zinc-coated
MIR00375
W
H
D
wxl
For rack type
Order no.
■ Color
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .8:
RAL 7021 dark gray
UP
482.6 88.1
600/800/900/1000442 x 280 Miracel/Smaract 01.113.736.1
1 unit
482.6 88.1
600/800/900/1000442 x 380 Miracel/Smaract 01.113.737.1
1 unit
482.6 88.1
500/600/800
442 x 280 DoubleProRack
01.113.736.1
1 unit
482.6 88.1
500/600/800
442 x 380 DoubleProRack
01.113.737.1
1 unit
482.6 88.1
400/500/600
442 x 280 ConAct
01.113.736.1
1 unit
482.6 88.1
500/600
442 x 380 ConAct
01.113.737.1
1 unit
■ Load rating
150 N static
■ Supply schedule
1 19” drawer with lock, including key
1 pair of telescopic slides
Mounting material
■ How supplied
Preassembled
19” Shelf, 2 U
Adjustable
– For installation in racks with adjustable
19” installation on the front
– Quick and easy mounting on 19” extrusions
– Also for swing frame in the 19” rack and
19” enclosure
– Adjustable in increments of 25 mm in
the depth
MIR00102
■ Material/Finish
Sheet steel 1.5 mm, powder-coated
Texture
SCH00054
W
U
For rack type
Order no.
UP
482.6 43.6 600-1000
H
D
1
Miracel/Smaract/
01.113.926.1
1 unit
482.6 88.1 600-1000
2
Miracel/Smaract/
01.113.927.1
1 unit
01.113.927.8
1 unit
01.113.928.1
1 unit
DoubleProRack/ConAct
DoubleProRack/ConAct
482.6 88.1 600-1000
2
Miracel/Smaract/
DoubleProRack/ConAct
■ Color
RAL 7035 light gray
482.6 132.5 600-1000
3
Miracel/Smaract/
DoubleProRack/ConAct
■ Load rating
200 N static
■ How supplied
Flat-packed kit
MIR00103
W
H
D
wxl
For rack type
Order no.
UP
482.6 88.1 600/800/900/1000 442 x 280 Miracel/Smaract 01.113.409.1
1 unit
482.6 88.1 600/800/900/1000 442 x 380 Miracel/Smaract 01.113.410.1
1 unit
Dimensions in mm: W
H
D
h
d
L
CW
Conversion:
=
=
=
=
=
=
=
Width
U
Height
Depth
UP
installation height kg
useful depth
WxL
length
Clear width
1 mm = 0.03937 inch
= standard height unit
1 U = 44.45 mm
= unit of packaging
= weight
= Surface area
= Express item
1 kg = 2.2046 pound
Knürr System Accessories
W
19” Shelf, 1 U
Pull-out
– With handle
– Can also be used as writing board
MEC00118
DRack
U d
wxl
U d
L
For rack type
600 1 365 400 Miracel/Smaract LAN
Order no.
UP
02.045.151.1
1 unit
482.6
43.6
600 1 440 400 Miracel/Smaract 19”
02.045.151.1
1 unit
482.6
87.1
600 2 440 400 Miracel/Smaract 19”
02.045.152.1
1 unit
482.6 131.5 600 3 440 400 Miracel/Smaract 19”
02.045.153.1
1 unit
482.6 176.0 600 4 440 400 Miracel/Smaract 19”
02.045.154.1
1 unit
■ Finish/Color
Powder-coated texture
RAL 7035 light gray
482.6
43.6
800 1 565 400 Miracel/Smaract LAN
02.045.151.1
1 unit
482.6
87.1
800 2 565 400 Miracel/Smaract LAN
02.045.152.1
1 unit
482.6 131.5 800 3 565 400 Miracel/Smaract LAN
02.045.153.1
1 unit
■ Load rating
200 N static
482.6 176.0 800 4 565 400 Miracel/Smaract LAN
02.045.154.1
1 unit
■ Supply schedule
1 shelf
1 pair of telescopic slides
Mounting material
482.6
02.045.161.1
1 unit
MEC20118
H
D
43.6
■ Material/Finish
Shelf, sheet steel, 1.0 mm
Telescopic slide, cold rolled steel
■ How supplied
Preassembled
W
H
482.6
For rack type
Order no.
UP
43.6
800 1 640 600 Miracel/Smaract 19”
482.6
43.6
900 1 665 600 Miracel/Smaract LAN
02.045.161.1
1 unit
482.6
87.1
900 2 665 600 Miracel/Smaract LAN
02.045.162.1
1 unit
482.6 131.5
900 3 665 600 Miracel/Smaract LAN
02.045.163.1
1 unit
482.6 176.0
900 4 665 600 Miracel/Smaract LAN
02.045.164.1
1 unit
482.6
43.6
900 1 740 600 Miracel/Smaract 19” server02.045.161.1
1 unit
482.6
87.1
900 2 740 600 Miracel/Smaract 19” server02.045.162.1
1 unit
482.6 131.5 900 3 740 600 Miracel/Smaract 19” server02.045.163.1
1 unit
482.6 176.0
1 unit
900 4 740 600 Miracel/Smaract 19” server02.045.164.1
482.6 43.6
600 1 365 403 x 400 Miracel/Smaract LAN 02.045.149.1
1 unit
482.6 43.6
600 1 440 403 x 400 Miracel/Smaract 19” 02.045.149.1
1 unit
482.6
43.6 1000 1 740 600 Miracel/Smaract 19” server02.045.161.1
1 unit
482.6 43.6
800 1 565 403 x 400 Miracel/Smaract LAN 02.045.149.1
1 unit
482.6
87.1 1000 2 740 600 Miracel/Smaract 19” server02.045.162.1
1 unit
482.6 43.6
800 1 640 403 x 600 Miracel/Smaract 19” 02.045.147.1
1 unit
482.6 131.5 1000 3 740 600 Miracel/Smaract 19” server02.045.163.1
1 unit
482.6 43.6
900 1 665 403 x 600 Miracel/Smaract LAN 02.045.147.1
1 unit
482.6 176.0 1000 4 740 600 Miracel/Smaract 19” server02.045.164.1
1 unit
482.6 43.6
900 1 740 403 x 600 Miracel/
02.045.147.1
1 unit
482.6
43.6
600 1 435 400 DoubleProRack with door 02.045.151.1
1 unit
482.6 43.6 1000 1 740 403 x 600 Miracel 19” Server
02.045.147.1
1 unit
482.6
87.1
600 2 435 400 DoubleProRack with door 02.045.152.1
1 unit
482.6 131.5
600 3 435 400 DoubleProRack with door 02.045.153.1
1 unit
482.6 43.6
600 1 435 403 x 400 DoubleProRack
02.045.149.1
1 unit
482.6 176.0 600 4 435 400 DoubleProRack with door 02.045.154.1
1 unit
482.6 43.6
800 1 635 403 x 600 DoubleProRack
02.045.147.1
1 unit
Smaract 19” Server
With door
With door
19” Drawer with Lock
Mounting on 19”
installation, front and rear
SCH00057
– For mounting in racks with fixed
19”installation on the front and rear
– Full pull-out
– With lock
43.6 800 1 635 600 DoubleProRack with door 02.045.161.1
1 unit
87.1
1 unit
800 2 635 600 DoubleProRack with door 02.045.162.1
482.6 131.5 800 3 635 600 DoubleProRack with door 02.045.163.1
1 unit
482.6 176.0 800 4 635 600 DoubleProRack with door 02.045.164.1
1 unit
482.6 43.6
500 1 460 400 DoubleProRack 19” no door02.045.151.1
1 unit
482.6 87.1
500 2 460 400 DoubleProRack 19” no door02.045.152.1
1 unit
482.6 131.5 500 3 460 400 DoubleProRack 19” no door02.045.153.1
1 unit
482.6 176.0 500 4 460 400 DoubleProRack 19” no door02.045.154.1
1 unit
482.6
43.6
600 1 560 400 DoubleProRack 19” no door02.045.151.1
1 unit
482.6
87.1
600 2 560 400 DoubleProRack 19” no door02.045.152.1
1 unit
■ Material/Finish
Drawer, sheet steel 1.0 mm,powdercoated texture
Telescopic slides, cold rolled steel,
sendzimir zinc-coated
482.6 131.5 600 3 560 400 DoubleProRack 19” no door02.045.153.1
1 unit
482.6 176.0 600 4 560 400 DoubleProRack 19” no door02.045.154.1
1 unit
482.6
43.6
700 1 660 600 DoubleProRack 19” no door02.045.161.1
1 unit
■ Color
Drawer, RAL7035 light-gray
482.6
87.1
700 2 660 600 DoubleProRack 19” no door02.045.162.1
1 unit
482.6 131.5 700 3 660 600 DoubleProRack 19” no door02.045.163.1
1 unit
■ Load rating
1 U - 200 N static
2 U - 400 N static
3 U - 400 N static
4 U - 400 N static
482.6 176.0
700 4 660 600 DoubleProRack 19” no door02.045.164.1
1 unit
■ Supply schedule
1 19” drawer with lock, including key
1 pair of telescopic slides
Mounting material
SCH00053
482.6
482.6
■ How supplied
Preassembled
Dimensions in mm: W
H
D
h
d
L
CW
Conversion:
=
=
=
=
=
=
=
Width
U
Height
Depth
UP
installation height kg
useful depth
WxL
length
Clear width
1 mm = 0.03937 inch
= standard height unit
1 U = 44.45 mm
= unit of packaging
= weight
= Surface area
= Express item
1 kg = 2.2046 pound
Knürr System Accessories
+ 5 V/DC max. 18 mA
- Mains cable (1.6 m) with tapping for
two 6-pin mini DIN plugs (PS/2)
- For Windows 98/ME/NT/2000/XP
Writing board For 19”
drawer with lock
■ Dimensions
Length x width x height
370 x 138.5 x 20 mm
– For drawer depth 400 mm and 600 mm
■ Material/Finish
Sheet steel, 1.0 mm, powder-coated
texture
SCH00062
W H
■ Color
RAL 7035 light gray
S
U
A1 A2 Pmax
Model
Order no.
UP
German
06.002.048.3
1 unit
■ Supply schedule
1 writing board
Mounting material
Chassis Rail
Hang-on and screw-on
■ How supplied
Flat-packed kit
W
H
D
U
d L
Order no.
UP
400
For rack type
02.045.202.9
1 unit
600
02.045.203.9
1 unit
–
–
–
–
For installation in 19” rack and enclosure
Hang-on for quick and easy mounting
Can also be screwed for heavier load ratings
Can be screwed from inside (use in rack
suites)
– Height setting possible for various main
section heights
MEC20162
■ Material/Finish
Sheet steel, 2.0 mm
Zinc-passivated, blue chrome-plated
19” Keyboard Drawer 1 U
For 19” keyboard
■ Load rating
1000 N max., with even
distribution
– With hand support
– With cable strain relief
– No telescopic slides locking
SCH00059
MEC20167
■ Material
Main unit, sheet steel, 1.0 mm
Front panel, sheet steel, 1.0 mm
■ Supply schedule
2 slot-in rails
Mounting material
■ Finish/Color
Powder-coated texture, RAL 7035 light
gray
■ How supplied
In pairs
■ Note
When selecting the slot-in rail, please
note the chassis depth d of the rack or
enclosure 4 19” extrusions are required
for mounting
MEC20167
■ Supply schedule
1 19” keyboard drawer, 1 U
1 pair of telescopic slides
Velcro strip for keyboard fixing
Mounting material
■ How supplied
Preassembled
W
H
SCH00055
DRack
U
d
L
For rack type
Order no.
UP
600
365 336 Miracel/Smaract
01.103.051.0
1 pair
600
440 411 Miracel/Smaract
01.103.052.0
1 pair
d L For rack type
Order no.
UP
800
565 536 Miracel/Smaract
01.103.053.0
1 pair
482.6 43.6
600 1
440 Miracel/Smaract 19”
02.011.101.1
1 unit
800
640 611 Miracel/Smaract
01.103.054.0
1 pair
482.6 43.6
800 1
565 Miracel/Smaract LAN
02.011.101.1
1 unit
900
665 636 Miracel/Smaract
01.103.055.0
1 pair
From900
740 711 Miracel/Smaract/CoolTherm 01.103.056.0
1 pair
W
H
DRack U
482.6 43.6
800 1
640 Miracel/Smaract 19”
02.011.101.1
1 unit
482.6 43.6
900 1
665 Miracel/Smaract LAN
02.011.101.1
1 unit
482.6 43.6
900 1
740 Miracel/Smaract 19” Server 02.011.101.1
1 unit
482.6 43.6
1000 1
740 Miracel 19” Server
02.011.101.1
1 unit
482.6 43.6
600 1
435 DoubleProRack with door 02.011.101.1
1 unit
482.6 43.6
800 1
635 DoubleProRack with door 02.011.101.1
1 unit
19” Compact Keyboard
IBM-compatible keyboard
with trackball
– Suitable for keyboard drawer 01.136.378.1
– Flat keyboard with 84 keys and integrated
trackball
VHP00155
■ Electrical data
- Power supply:
Aluminum Chassis Rail
Screw-on
MEC20169
– For installation in 19” rack and enclosure
– Can be screwed from inside (use in rack
suites)
– Height setting possible for various main
section heights
■ Material/Finish
Extruded aluminum, 1.4 mm, polished
■ Load rating
700 N max., with even load distribution
Knürr System Accessories
■ Supply schedule
2 slot-in rails
Mounting material
Quick-Fix 19” Blanking Panel
Assembly without tools
■ How supplied
In pairs
■ Note
When selecting the slot-in rail, please
note the chassis depth d of the rack or
enclosure 4 19” extrusions are required
for mounting.
WRack HRack DRack
U d
L
For rack type
– For covering free 19” spaces (cold-hot
separation)
– Quick and easy assembly without tools
(one click) and disassembly (quarter
turn)
– Suitable for 9.5 x 9.5 square holes
MEC20179
■ Material
Sheet steel, 1.0 mm
Order no.
UP
600
365 336 Miracel/Smaract
01.103.101.0
1 pair
600
440 411 Miracel/Smaract
01.103.102.0
1 pair
800
565 536 Miracel/Smaract
01.103.103.0
1 pair
800
640 611 Miracel/Smaract
01.103.104.0
1 pair
800
665 636 Miracel/Smaract
01.103.105.0
1 pair
From 900
740 711 Miracel/Smaract/CoolTherm01.103.106.0
1 pair
500
285 254 ConAct
01.103.111.0
1 pair
600
385 354 ConAct
01.103.112.0
1 pair
600
435 403 DoubleProRack with door 01.103.118.0
1 pair
800
635 603 DoubleProRack with door 01.103.119.0
1 pair
500
460 428 DoubleProRack no door
1 pair
W
Order no.
UP
1
Powder-coated
01.103.301.X
6 units
01.103.122.0
■ Finish
Final digit of order number .1:
Powder-coated texture, RAL7035,
light gray
Final digit of order number .8:
Powder-coated texture, RAL7021,
dark gray
MEC20180
■ Supply schedule
X (see ON for quantity) Quick-Fix 19”
Blanking Panel
Mounting material
■ How supplied
In sets (see ON for quantity); fixing clips
pre-mounted
MEC20178
H
D
U
600
560 528 DoubleProRack no door
01.103.123.0
1 pair
700
660 628 DoubleProRack no door 01.103.124.0
1 pair
482.6 88.1
2
Powder-coated
01.103.302.X
3 units
482.6 132.5
3
Powder-coated
01.103.303.X
2 unit
Chassis runner,
depth-variable Screw-on
482.6 265.9
6
Powder-coated
01.103.306.X
1 unit
482.6 399.2
9
Powder-coated
01.103.309.X
2 unit
482.6 932.6
21
Powder-coated
01.103.321.X
1 unit
– For installation in 19” rack and enclosure
– Depth-variable
– Can be screwed from inside (use in rack
suites)
– Height setting possible for various main
section heights
MEC20163
■ Material/Finish
Sheet steel, 1.25 mm
Zinc-passivated, blue chrome-plated
Quick-Fix 19” blanking
panel cable port
Assembly without tools
– For orderly cable management in the
rack internal space
– Quick and easy assembly without tools
(one click) and disassembly (quarter
turn)
– Suitable for 9.5 x 9.5 square holes
MEC20181
■ Load rating
200 N max., with even load distribution
■ Material
Sheet steel, 1.0 mm
■ Supply schedule
2 basic rails
2 extension rails
Mounting material
MEC20166
■ How supplied
In pairs
■ Finish
Final digit of order number .1:
Powder-coated texture, RAL7035,
light gray
Final digit of order number .8:
Powder-coated texture, RAL7021,
dark gray
MEC20178
■ Note
When selecting the slot-in rail, please
note the chassis depth d of the rack or
enclosure 4 19” extrusions are required
for mounting
W
H
d L For rack type
482.6 43.6
D
U
d
For rack type
Order no.
■ Supply schedule
6 Quick-Fix 19” blanking panel cable ports
Mounting material
■ How supplied
In sets; fixing clips pre-mounted
UP
600
365-440 Miracel/Smaract 01.103.091.0
1 pair
W
800-1200
565-740 Miracel/Smaract 01.103.092.0
1 pair
482.6 43.6
H
900-1200
740
CoolTherm
01.103.092.0
1 pair
600
385
ConAct
01.103.091.0
1 pair
500-600
435-460 DoubleProRack
01.103.091.0
1 pair
600-800
560-660 DoubleProRack
01.103.092.0
1 pair
D
U
1
d L For rack type
Powder-coated
Order no.
UP
01.103.331.X
6 units
Knürr System Accessories
Quick-Fix 19” Blanking
Panel Screw-on
19” front panel
Aluminum 3 mm
■ Material/Finish
Final digit of order number .0:
AlMg3 - F23 polished with lamination
sheet
Final digit of order number .1:
AlMg3 - F23, powder-coated, RAL 7035
light gray
Final digit of order number .6:
AlMg3 - F23 EB (anodize-enabled),
anodized E6/EV1
Final digit of order number .8:
AlMg3 - F23, powder-coated, RAL 7021
dark gray
– For covering free 19” spaces (cold-hot
separation)
■ Material
Sheet steel, 1.0 mm
CUD00005
FR000005
■ Finish
Final digit of order number .1:
Powder-coated texture, RAL7035,
light gray
Final digit of order number .8:
Powder-coated texture, RAL7021,
dark gray
■ Supply schedule
X (see ON for quantity) 19” Blanking
Panel
CUD00004
■ Supply schedule
1 19” front panel
■ How supplied
In units
■ How supplied
In sets (see ON for quantity)
■ Note
Please also order front panel mounting
material.
■ Note
Please also order front panel mounting
material!
W
H
D
482.6 43.6
U
d L For rack type
1
Powder-coated
Order no.
UP
01.103.201.X
6 units
MEC20109
482.6 88.1
2
Powder-coated
01.103.202.X
3 units
H
482.6 132.5
3
Powder-coated
01.103.203.X
2 unit
43.6
X
Y
31.7
U
Model
Order no.
UP
1
Polished
02.008.021.0
1 unit
482.6 265.9
6
Powder-coated
01.103.206.X
1 uni
88.1
76.2
2
Polished
02.008.022.0
1 unit
482.6 399.2
9
Powder-coated
01.103.209.X
2 unit
132.5
57.1
3
Polished
02.008.023.0
1 unit
177.0
101.6
4
Polished
02.008.024.0
1 unit
221.4
146.0
5
Polished
02.008.025.0
1 unit
265.9 76.2 190.4
6
Polished
02.008.026.0
1 unit
19” Ventilation Front Panel
– For additional ventilation of 19” racks
and 19” pedestals in accordance with
IEC 297
LUF00217
■ Material
Aluminum
■ Finish
Final digit of order number .1:
Powder-coated, RAL 7035 light-gray
Final digit of order number .6:
colorless anodized E 6 / EV 1
H
43.6
X
Y
U
31.7 1
31.7
1
Powder-coated, RAL 7035 02.008.021.1
1 unit
88.1
76.2
2
Powder-coated, RAL 7035 02.008.022.1
1 unit
132.5
57.1
3
Powder-coated, RAL 7035 02.008.023.1
1 unit
177.0
101.6
4
Powder-coated, RAL 7035 02.008.024.1
1 unit
221.4
146.0
5
Powder-coated, RAL 7035 02.008.025.1
1 unit
265.9 76.2 190.4
6
Powder-coated, RAL 7035 02.008.026.1
1 unit
43.6
31.7
1
Powder-coated, RAL 7021 02.008.021.8
1 unit
88.1
76.2
2
Powder-coated, RAL 7021 02.008.022.8
1 unit
132.5
57.1
3
Powder-coated, RAL 7021 02.008.023.8
1 unit
43.6 31.7
1
Anodized
02.008.071.6
1 unit
88.1
76.2
2
Anodized
02.008.072.6
1 unit
■ How supplied
In units
132.5
57.1
3
Anodized
02.008.073.6
1 unit
177.0
101.6
4
Anodized
02.008.074.6
1 unit
■ Note
Please also order front panel mounting
material.
221.4
146.0
5
Anodized
02.008.075.6
1 unit
265.9 76.2 190.4
6
Anodized
02.008.076.6
1 unit
■ Supply schedule
1 ventilation front panel
MEC20110
43.6
Model
Order no.
UP
Powder-coated, RAL 7035
02.008.101.1
1 unit
43.6
31.7 1
Anodized
02.008.101.6
1 unit
132.5
57.1 3
Powder-coated, RAL 7035
02.008.103.1
1 unit
132.5
57.1 3
Anodized
02.008.103.6
1 unit
19” Front Panel, Hinged
– With 19” adapter and hinge
■ Material
Aluminum 3 mm
Dimensions in mm: W
H
D
h
d
L
CW
Conversion:
=
=
=
=
=
=
=
Width
U
Height
Depth
UP
installation height kg
useful depth
WxL
length
Clear width
1 mm = 0.03937 inch
= standard height unit
1 U = 44.45 mm
= unit of packaging
= weight
= Surface area
= Express item
1 kg = 2.2046 pound
■ Finish
Anodized
FRO00007
■ Supply schedule
1 front panel, hinged
1 19” adapter
1 hinge
Knürr System Accessories
■ How supplied
Flat-packed kit
Document Holder
■ Note
Please also order front panel mounting
material.
– Self-adhesive; use 6 mm bore holes with
higher stresses
– For DIN A4 documents
■ Material
High-impact PS
FR000006
W
H
D
U
Model
Order no.
■ Color
Gray
UP
3
Anodized
01.110.780.6
1 unit
6
Anodized
01.110.781.6
1 unit
■ Supply schedule
1 document holder
MEC20027
W
L
D
Order no.
UP
264
236
30
05.016.045.0
1 unit
19” Front Ventilation Panel
– For additional ventilation of 19” racks
and 19” pedestals in acc. with IEC 297
■ Material/Color
Final digit of order number .1:
ABS (UL 94 V0), light gray RAL 7035
Final digit of order number .9:
ABS (UL 94 V0), dark gray RAL 9011
LUF88006
■ Supply schedule
1 front ventilation panel
2 connection holders
LUF00093
■ How supplied
Flat-packed kit
■ Note
Please also order front panel mounting
material.
W
H
Order no.
UP
483
43.6
D
1
U
Model
02.008.111.1
1 unit
483
43.6
1
02.008.111.9
1 unit
Panel Filter
For 19” front ventilation panel
– For use in conjunction with the 19” front
ventilation panel
MEC20144
■ Material/Color
Filter fibers and screen cloth
■ Supply schedule
1 panel filter
Mounting material
MEC20149
■ How supplied
Flat-packed kit
W
H
D
U
1
Model
Order no.
UP
02.008.131.9
1 unit
Dimensions in mm: W
H
D
h
d
L
CW
Conversion:
=
=
=
=
=
=
=
Width
U
Height
Depth
UP
installation height kg
useful depth
WxL
length
Clear width
1 mm = 0.03937 inch
= standard height unit
1 U = 44.45 mm
= unit of packaging
= weight
= Surface area
= Express item
1 kg = 2.2046 pound
Knürr System Accessories
Ball Bearing Telescopic Slide, BP-400-LR
Part pull-out
mL(N)
A
B
C
D
500
330
220.5
328
279.4
E
F
G
152.4
101.6
H
I
63.5
K
Order no. 1
UP
111.1
05.043.613.7
1 pair
460
356
245.5
354
304.8
177.8
101.6
88.9
111.1
05.043.614.7
1 pair
400
406
296.5
404
355.6
228.6
101.6
139.7
111.1
05.043.616.7
1 pair
490
457
330.5
455
406.4
203.2
101.6
101.6
88.9
111.1
05.043.618.7
1 pair
440
508
381.5
505
457.2
228.6
101.6
127
114.3
111.1
05.043.620.7
1 pair
410
533
407
531
482.6
241.3
101.6
139.7
127
111.1
05.043.621.7
1 pair
600
559
386.8
557
508
406.4
254
101.6
152.4
139.7
111.1
05.043.622.7
1 pair
540
610
437.7
608
558.8
457.2
279.4
101.6
177.8
165.1
111.1
05.043.624.7
1 pair
500
660
488.5
658
609.6
508
304.8
101.6
203.2
190.5
111.1
05.043.626.7
1 pair
600
711
500
709
660.4
558.8
330.2
101.6
228.6
215.6
111.1
05.043.628.7
1 pair
– 3/4 pull-out, two-part
– Locking in pulled-out position (friction
lock)
– Quick mechanism for removing and
connecting slot-in without tools
TEL00173
■ Material
Cold rolled steel
■ Finish
Sendizimir zinc-passivated
■ Load rating
400 - 600 N static per slide pair
depending on length
TEL20003
■ Supply schedule
1 pair of telescopic slides
■ How supplied
Flat-packed kit
■ Note
Please also order assembly set, order
number 05.043.595.9
Stop Spring for Ball Bearing
Telescopic Slides
– Quick and easy conversion from form
lock to friction lock and vice versa
– Conversion also possible at any later stage
■ Material
Spring steel
TEL20010
W
H
■ Supply schedule
Set of 10 units
D
Dimensions in mm: W
H
D
h
d
L
CW
Conversion:
U
=
=
=
=
=
=
=
Model
Order no.
UP
Form lock
05.043.666.9
10 unit
Friction lock
05.043.667.9
10 unit
Width
U
Height
Depth
UP
installation height kg
useful depth
WxL
length
Clear width
1 mm = 0.03937 inch
= standard height unit
1 U = 44.45 mm
= unit of packaging
= weight
= Surface area
= Express item
1 kg = 2.2046 pound
Knürr System Accessories
Ball Bearing Telescopic Slide, BF-480-FLR
Full pull-out
mL(N)
A
B
C
D
E
F
455
356
381
354
323.9
311.2
298.5
G
H
I
200
0
K
Order no. 1
UP
05.043.854.7
1 pair
490
406
432.5
404
374.7
362
349.3
139.7
111.1
05.043.856.7
1 pair
495
457
483.5
455
425.5
412.8
400.1
212.7
190.5
111.1
05.043.858.7
1 pair
510
508
530.5
506
476.3
463.6
450.9
365.1
238.1
241.3
111.1
05.043.860.7
1 pair
510
559
584.5
557
527.1
514.4
501.7
415.9
263.5
292.1
111.1
05.043.862.7
1 pair
515
610
635.5
608
277.9
565.2
552.5
466.7
288.9
342.9
111.1
05.043.864.7
1 pair
520
660
686.5
658
628.7
616
603.3
517.5
314.3
393.7
111.1
05.043.866.7
1 pair
520
711
737.5
709
679.5
666.8
654.1
568.3
339.7
444.5
111.1
05.043.868.7
1 pair
– Full pull-out, three-part
– Locking in pulled-out position (form lock)
– Quick mechanism for removing and
connecting slot-in without tools
■ Material
Cold rolled steel
TEL00173
■ Finish
Sendizimir zinc-passivated
■ Load rating
455 - 520 N static per slide pair depending
on length
TEL20011
■ Supply schedule
1 pair of telescopic slides
■ How supplied
Flat-packed kit
■ Note
Please also order assembly set, order
number 05.043.595.9
Assembly set for
Ball Bearing Slides
– For quick and easy assembly of telescopic
slides, BP-400-LR and BF-480-FLR
■ Material
Zincorium plate, 1.5 mm
TEL00012
■ Supply schedule
4 mounting brackets Mounting material
■ How supplied
Flat-packed kit
W
H
D
U
Model
Order no.
UP
Form lock
05.043.595.9
1 set
Dimensions in mm: W
H
D
h
d
L
CW
Conversion:
=
=
=
=
=
=
=
Width
U
Height
Depth
UP
installation height kg
useful depth
WxL
length
Clear width
1 mm = 0.03937 inch
= standard height unit
1 U = 44.45 mm
= unit of packaging
= weight
= Surface area
= Express item
1 kg = 2.2046 pound
Knürr System Accessories
The right mounting set for every rack type
Miracel
Miracel
Miracel
Miracel
Smaract Smaract Smaract
T-slot Mount. holes Server Swing frame T-slot Mount. holes Server
Double-
Double-
ProRack
ProRack
ConAct
T-slot Mount. holes
Name
Order no.
UP
Mounting set
05.041.320.9
1 set
05.041.321.9
1 set
05.041.325.9
1 set
05.041.323.9
1 set
05.041.322.9
1 set
05.041.324.9
1 set
Name
Order no.
UP
FP mounting set
05.041.335.9
1 set
05.041.336.9
1 set
05.041.337.9
1 set
05.041.338.9
1 set
Name
Order no.
UP
FP mounting set
05.041.340.9
1 set
05.041.341.9
1 set
05.041.342.9
1 set
05.041.343.9
1 set
T-slot, M5 wide
Mounting set
Mount. holes, M5/BI 1.5
Mounting set
Mount. holes M5/BI 2.5
Mounting set
dpr T-slot, M5 narrow
Mounting set
dpr Mount. holes, M5
Mounting set
ConAct M5
The right mounting set for front panel mounting
Model: Z-form screw
Miracel
Miracel
Miracel
Miracel
Smaract Smaract Smaract
T-slot Mount. holes Server Swing frame T-slot Mount. holes Server
Double-
Double-
ProRack
ProRack
ConAct
T-slot Mount. holes
T-slot, M5 wide
FP mounting set
Mount. holes M5/BI 1.5
FP mounting set
Mount. holes M5/BI 2.5
FP mounting set
T-slot, M5 narrow
Model: Countersunk screw+rosette
Miracel
Miracel
Miracel
Miracel
Smaract Smaract Smaract
T-slot Mount. holes Server Swing frame T-slot Mount. holes Server
Double-
Double-
ProRack
ProRack
T-slot Mount. holes
ConAct
T-slot, M5 wide
FP mounting set
Mount. holes M5/BI 1.5
FP mounting set
Mount. holes M5/BI 2.5
FP mounting set
T-slot, M5 narrow
Dimensions in mm: W
H
D
h
d
L
Conversion:
=
=
=
=
=
=
Width
U = standard height unit
Height
1 U = 44.45 mm
Depth
UP = unit of packaging
installation height kg = weight
useful depth
length
= Express item
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Knürr System Accessories
The right accessories for every rack type
Miracel
Miracel
Miracel
Miracel
Smaract Smaract Smaract
T-slot Mount. holes Server Swing frame T-slot Mount. holes Server
Double-
Double-
ProRack
ProRack
T-slot Mount. holes
ConAct
Name
Order no.
UP
Spring nut
01.350.431.9
1 set
05.041.503.9
1 set
01.350.405.9
1 set
05.041.513.7
1 set
05.041.518.7
1 set
05.041.330.9
1 set
05.041.331.9
1 set
05.041.203.9
1 set
05.041.290.9
1 set
M5 wide
Spring nut
M5 narrow
Spring nut
M6
Caged nut
M5/BI 1.5
Caged nut
M5/BI 2.5
Oval head screw
Z-form M5 x 10
Oval head screw
Z-form M5 x 16
Countersunk screw
M5 x 12 + rosette
Countersunk screw
M5 x 16 + rosette
Mounting Tool for Caged
Nut
– Makes clipping the caged nut into the
extrusion easier
MIR00114
■ Material
Spring steel
■ Supply schedule
1 mounting tool
W
H
D
Dimensions in mm: W
H
D
h
d
L
Conversion:
U
=
=
=
=
=
=
d L
Model
Width
U = standard height unit
Height
1 U = 44.45 mm
Depth
UP = unit of packaging
installation height kg = weight
useful depth
length
= Express item
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Order no.
UP
01.130.985.9
1 unit
Knürr System Accessories
T-Slot Mounting set, M5, Wide
For Miracel®/ Smaract®
MEC20125
Mounting Holes Mounting
Set, M5 For DoubleProRack®
- For mounting 19” front panels and 19”
components
– For mounting 19” front panels and 19”
components
■ Supply schedule
100 spring nuts M5, wide
100 oval head screws, Z-form, M5 x 10
20 caged nuts, M5 / plate, 1.5 mm
20 cylinder screws, M5 x 8
■ Supply schedule
100 caged nuts M5 / plate, 2.5 mm
50 oval head screws, Z form, M5 x 16
40 spring nuts, M5 narrow
40 cylinder screws, M5 x 10
MEC20126
■ How supplied
Flat-packed kit
■ How supplied
Flat-packed kit
W
H
D
U
d L
Model
Order no.
UP
05.041.320.9
1 set
W
H
D
U
d L
Model
Mounting Holes Mounting
Set, M5 / Plate, 1.5 mm
For Miracel®/ Smaract®
MEC20126
H
D
U
d L
Model
Order no.
UP
05.041.321.9
1 set
Mounting Holes-Server
Extrusion Mounting Set M5 / Plate
2.5 mm for Miracel®/ Smaract®
– For mounting 19” front panels and 19”
components
■ Supply schedule
100 caged nuts M5 / plate, 2.5 mm
100 oval head screws, Z form, M5 x 16
20 spring nuts, M5 wide
20 cylinder screws, M5 x 8
MEC20126
■ Supply schedule
50 caged nuts M5 / plate, 1.5 mm
50 oval head screws, Z-form, M5 x 16
50 cylinder screws, M5 x 8
25 locking nuts, M5
MEC20096
■ How supplied
Flat-packed kit
W
H
D
U
d L
Model
H
D
U
d L
Model
Order no.
UP
05.041.325.9
1 set
– For mounting 19” front panels and 19”
components
■ Supply schedule
100 spring nuts, M5 narrow
20 oval head screws, Z form, M5 x 10
50 cylinder screws, M5 x 10
30 oval head screws, Z form, M5 x 8
MEC20127
■ How supplied
Flat-packed kit
W
H
D
U
d L
Model
Order no.
UP
05.041.323.9
1 set
■ How supplied
Flat-packed kit
MEC20130
T-Slot Mounting set, M5,
Narrow for DoubleProRack®
Type 1
MEC20098
1 set
■ Supply schedule
Type 1:
50 spring nuts, M5 wide
50 oval head screws, Z-form, M5 x 10
Type 2:
50 spring nuts, M5 wide
50 countersunk screws, M5 x 12
50 rosettes
Type 2
H
UP
– For mounting 19” front panels and 19”
components
MEC20129
W
Order no.
05.041.324.9
Front panel mounting set,
T-slot, M5 wide
For Miracel®/ Smaract®
Type 1
■ How supplied
Flat-packed kit
W
1 set
– For mounting 19” front panels and 19”
components
■ How supplied
Flat-packed kit
W
UP
Mounting Holes Mounting
Set, M5 For ConAct®
– For mounting 19” front panels and 19”
components
■ Supply schedule
100 caged nuts M5 / plate, 1.5 mm
100 oval head screws, Z form, M5 x 16
20 spring nuts, M5 wide
20 cylinder screws, M5 x 8
Order no.
05.041.322.9
D
U
d L Model
Order no.
UP
Type 1: Z-form screw
05.041.335.9
1 set
Type 2: Screw+rosette
05.041.340.9
1 set
Front Panel Mounting Set,
Mounting Holes, M5/Plate, 1.5 mm
For Miracel®/ Smaract®/ ConAct®
– For mounting 19” front panels and 19”
components
■ Supply schedule
Type 1:
50 caged nuts M5 / plate, 1.5 mm
50 oval head screws, Z-form, M5 x 16
Type 2:
50 caged nuts M5 /plate, 1.5 mm
50 countersunk screws, M5 x 16
50 rosettes
Knürr System Accessories
■ How supplied
Flat-packed kit
Type 2
■ Supply schedule
50 spring nuts
■ How supplied
Flat-packed kit
W
H
D
U
d L Model
MEC20097
W
H
D
U
d L Model
Order no.
UP
Type 1: Z-form screw
05.041.336.9
1 set
Type 2: Screw+rosette
05.041.341.9
1 set
Order no.
UP
Type 1: M5 wide
01.350.431.9
1 set
Type 2: M5 narrow
05.041.503.9
1 set
Type 3: M6
01.350.405.9
1 set
Caged nut
Front Panel Mounting Set, Mounting
Holes, M5/Plate, 2.5 mm For Miracel®/
Smaract®/ DoubleProRack®
Type 1
– For mounting 19” front panels and 19”
components
MEC20098
D
U
d L Model
■ Supply schedule
50 caged nuts
■ How supplied
Flat-packed kit
W
■ How supplied
Flat-packed kit
MEC20097
H
Type 1: Plate, 1.5 mm
For Miracel / Smaract / ConAct / SoHo
Type 2: Plate, 2.5 mm
For Miracel Server / Smaract Server /
DoubleProRack mounting holes
MEC20139
■ Supply schedule
Type 1:
50 caged nuts M5 / plate, 2.5 mm
50 oval head screws, Z-form, M5 x 16
Type 2:
50 caged nuts M5 /plate, 2.5 mm
50 countersunk screws, M5 x 16
50 rosettes
Type 2
W
– For clipping into extrusions with mounting holes
Order no.
H
D
U
d L Model
Order no.
UP
M5: Type 1: Plate 1.5 mm 05.041.513.7
1 set
UP
M5: Type 2: Plate 2.5 mm 05.041.518.7
1 set
Type 1: Z-form screw
05.041.337.9
1 set
M6: Type 1: Plate 1.5 mm 05.041.514.7
1 set
Type 2: Screw+rosette
05.041.342.9
1 set
M6: Type 2: Plate 2.5 mm 05.041.519.7
1 set
Front Panel Mounting set,
T-Slot, M5, Narrow
For DoubleProRack®
Type 1
Oval Head Screw
– IEC DIN 967
– For mounting 19” front panels and 19”
components
MEC20129
■ Supply schedule
Type 1:
50 spring nuts, M5 narrow
50 oval head screws, Z-form, M5 x 10
Type 2:
50 spring nuts, M5 narrow
50 countersunk screws, M5 x 12
50 rosettes
Type 2
■ Supply schedule
50 oval head screws, Z-form
MEC20140
■ How supplied
Flat-packed kit
W
H
D
U
d L
■ How supplied
Flat-packed kit
MEC20130
W
H
D
U
d L Model
Order no.
Model
Order no.
UP
M5 x 10
05.041.330.9
1 set
M5 x 16
05.041.331.9
1 set
M6 x 10
05.041.332.9
1 set
M6 x 16
05.041.333.9
1 set
UP
Type 1: Z-form screw
05.041.338.9
1 set
Type 2: Screw+rosette
05.041.343.9
1 set
Countersunk Screw +
Rosette
– IEC DIN EN ISO 7047
Spring Nut
■ Supply schedule
50 countersunk screws
50 rosettes
MEC20141
■ How supplied
Flat-packed kit
– For clipping into T-slots at any position
MEC00060
Type 1: M5 wide for Miracel / Smaract
T-nut size: 10 x 13 mm
Type 2: M5 narrow for DoubleProRack
T-nut size: 8 x 13 mm
Type 3: M6 for Miracel / Smaract
T-nut size: 10 x 13 mm
W
H
D
U
d L
Model
Order no.
UP
M5 x 12
05.041.203.9
1 set
M5 x 16
05.041.290.9
1 set
Knürr System Accessories
Oval Head Screw
Self-guiding
Cable Entry Rail
– DIN 7500
– Suitable for system accessories fixed on
the inside of the 19” extrusions
– Suitable for 19” steel and 19” aluminum
extrusions
– Easy screwing
MEC80020
Alternative to cable entry via brush strips
when installing distributor box in open
frames
■ Material/ Finish
Sheet steel, zinc-passivated
HEI00234
■ Supply schedule
1 cable routing panel
11 bushing sockets
Mounting material
■ Supply schedule
50 oval head screws, M6x10
■ How supplied
Flat-packed kit
W
W
H
D
U
d L
Model
Order no.
UP
M6 x 10
05.041.334.9
1 set
H
D
Model
– Only for rack type Miracel W 700, W 800
– Mounting is made on the basic frame
above the vertical extrusions
– With 13 watt fluorescent tube
– With on/off rocker switch
– With 2 m power supply lead and EURO
plug
– Complete with mounting material
– Only with 123 mm front jumpering
space
– IEC DIN EN ISO 7045
■ Supply schedule
1 set of 50 units
ELM00058
MEC00014
H
D
U
d L
UP
1 unit
Luminestra
Rack Lighting
Oval Head Screw
With Phillips head
W
Order no.
03.013.386.1
Model
Order no.
UP
8
M 5 no washer
05.041.611.8
1 set
12
M 4 no washer
05.041.609.8
1 set
12
M 5 with washer 05.041.613.8
1 set
16
M 5 with washer 05.041.614.8
1 set
16
M 6 with washer 05.041.616.8
1 set
■ Color
White
■ Supply schedule
1 Luminestra rack lamp
2 mounting brackets
Mounting material
W
H
D
70
20
555
U
h d w
Model
Order no.
UP
01.131.227.9
1 unit
Cylinder Screw
With hexagon head
Compact Rack Lamp
– IEC ISO 4762 (modified)
■ Supply schedule
1 set of 50 units
MEC00013
W
H
■ Features
With magnetic mounting
Energy-saving lamp
Protective contact socket
On/off switch
3 m power supply lead
With cover panel
ELM00135
D
U
d L
Model
Order no.
UP
8
M5
05.041.574.8
1 set
8
M 5 microencapsulated 05.041.575.9
1 set
■ Approval
VDE, ICE
■ Protection rating IP20
■ Technical data
- Operating voltage 230 V / 50-60 Hz
- Lighting Compact fluorescent tube
with integrated starter
- Power consumption: 11 W =^ 75 W bulb
- Light intensity: 900 Lm
- Interference suppression in acc. with
VDE 0712, IEC 82
- Socket: 230 VAC / 16A
- Connections: 3-pole screw clamp
2.5 mm2 with strain relief
Tensiloc Nut
■ Material
Steel nickel-plated
■ Supply schedule
1 set of 50 units
MEC20021
W
H
D
U
d L
Model
Order no.
UP
M5
05.041.533.8
1 set
W
H
D
65
65
365
U
h d w
Model
Order no.
UP
01.131.465.9
1 unit
Knürr System Accessories
1 Distribution Box
Door Contact Switch
– For mounting installation technology
DIN rail components, such as fuses,
clamps, relays, etc.
– In the built-in status, the mounting level
can be pulled out at the front, locked in
position, and as a result,
significantly simplifies the wiring of the
individual components
Not with “fixed installation” model
On request: Delivered assembled and
wired
Further versions and models on
request
– Installation space for up to 22 pieces of
equipment with 18 mm width each
– Mounting of the TS35 DIN rail on several
levels with simple plug-in connection
Not with “fixed installation” version
– “Snap-in” mounting of DIN rail components
– Easy access to the protective earth and
neutral conductor rails from the front
– Various positioning options prepared
for N and PE rails
Not with “fixed installation” version
– Cable entry at the rear via double brush
strip (optionally via bushing sockets)
– Cable strain relief on the inside and
therefore accessible from the front
– Labeling strips on the front, above and
below the installation space
– Installation options for power distribution
with 230 V AC, but also in the low voltage
range (e.g. 48 V DC)
– 19” slot-in, 3 U, depth 150 mm
HEI00379
– On/off switch, 4 A, 230 V ~
– Activation with door opening and closing
■ Supply schedule
1 door contact switch (not wired)
1 mounting brackets
Mounting material
ELM00137
W
H
S
U
h d kg
Model
Order no.
UP
01.110.722.9
1 unit
1 Cable Junction Box
– For 230V electro-installation on-site
– As fixed-location exchange point
– Quick and easy mounting
■ Supply schedule
1 cable junction box
ELM00033
■ Material/ Finish
- Covers, powder-coated texture, RAL
7035 light gray
- Main unit, zinc-passivated sheet steel
■ Supply schedule
1 distribution box
Including N and PE rails, cable entry,
cable strain relief, empty panel covers
and earth set
ELM00034
■ How supplied
Fully assembled
W
W
H
D
U
19”
Model
Order no.
UP
482.6 134
150
3
Pull-out
03.013.385.1
1 unit
482.6 134
150
3
•
•
Fixed installation 03.013.470.1
1 unit
H
D
U
h d w
Model
Order no.
UP
00.078.720.9
1 unit
Modular Terminal Box
–
–
–
–
For 230V electro-installation on-site
With series terminal, 8 x 42
Pg 11/16 entry
IP 54
■ Material
High-impact, fire-resistant polystyrene
ELM00128
W
HEI20282
Dimensions in mm: W
H
D
h
d
L
Conversion:
=
=
=
=
=
=
Width
U = standard height unit
Height
1 U = 44.45 mm
Depth
UP = unit of packaging
installation height kg = weight
useful depth
length
= Express item
1 mm = 0.03937 inch
1 kg = 2.2046 pound
H
■ Supply schedule
1 modular terminal box
4 Pg compression glands, Pg11
S
U
h d kg
Model
Order no.
UP
01.117.521.9
1 unit
Knürr System Accessories
1 Equipotential Bonding Bar
– For central earthing of all protective
conductors
– With sealing cover
– Connection options:
– 1 x round conductor 8-10 mm Ø
– 1 x flat conductor up to 30 mm wide or
round conductor 8-10 mm Ø
– 7 x single or several-wire conductors up
to 16 mm2 or fine wire conductor up to
10 mm2
ELM00114
■ Material
Base and cover, high-impact plastic
Brass nickel-plated contact strip
■ Supply schedule
1 equipotential bonding bar
W
H
S
U
h d kg
Model
Order no.
UP
01.117.524.3
1 unit
Earthing Bar
– For safe earthing and equipotential
bonding of equipment and installation
components
■ Material
Electrolyte copper, 9x9
ELM00068
■ Supply schedule
1 earthing bar
2 brackets
Mounting material
W
H
S
Model
Order no.
UP
24
U h d
kg
For DoubleProRack
01.240.546.9
1 unit
21
For DoubleProRack
01.240.545.9
1 unit
18
For DoubleProRack
01.240.544.9
1 unit
15
For DoubleProRack
01.240.543.9
1 unit
45
For Miracel
01.110.709.9
1 unit
41
For Miracel
01.110.708.9
1 unit
12
For Miracel
01.110.703.9
1 unit
Contact Clamp
– For safe and secure connection of equipment and installation components with
the earthing bar
– For cables up to 25 mm2
■ Supply schedule
20 contact clamps
DOP20016
W
H
S
Dimensions in mm: W
H
D
h
d
L
Conversion:
U
=
=
=
=
=
=
h d kg
Model
Width
U = standard height unit
Height
1 U = 44.45 mm
Depth
UP = unit of packaging
installation height kg = weight
useful depth
length
= Express item
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Order no.
UP
01.110.715.9
20 unit
Emerson Network Power Rack PDUs
Rack PDUs
Emerson Network Power Rack PDUs
Over view : Emer son Net work Power Rack PDUs Europe
Merkmale
Power
distribution
Knürr DI-Strip Basic Rack PDU®
Liebert MPHTM
Managed Rack PDU
Liebert MPXTM
Adaptive Rack PDU
Knürr
DI-STRIP
Knürr
DI-STRIP M
Knürr
DI-STRIP RM
Liebert MPH
Branch
Monitored
Liebert MPH
controlled
Liebert MPX
Elementary
Liebert MPX
Liebert MPX
Elementary
Branch
Phase monitored monitored
Liebert MPX
Receptacle
managed
•
•
•
•
•
•
•
•
•
•
•
•
•
Fixed
Fixed
Modular
Modular
Modular
Modular
Modular
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
A,V,W,KWh,
Hz
A,V,W,KWh,
VA, Hz,
power factor
A,V,W,KWh,
VA, Hz,
power factor,
crest factor
Modular
Local display
Remote
interface
Measuring on
input level
Measuring per
group
Measuring per
output
•
Switching per
output
Measuring
parameters
A
A
A,V,W,KWh,
Hz
A,V,W,KWh,
Hz
Input power
1ph + 3ph
max 32A
1ph + 3ph
max 32A
1ph + 3ph
max 32A
1ph + 3ph
max 32A
1ph + 3ph
max 32A
1ph + 3ph
max 63A
1ph + 3ph
max 63A
1ph + 3ph
max 63A
1ph + 3ph
max 63A
Outputs
IEC C13&C19
Schuko
Switzerland
France
IEC C13&C19
Schuko
Switzerland
France
IEC C13&C19
Schuko
Switzerland
France
IEC C13&C19
IEC C13&C19
IEC C13&C19
Schuko
IEC C13&C19
Schuko
IEC C13&C19
Schuko
IEC C13&C19
Schuko
•
•
•
•
•
Different sensors
can be connected
All systems are RoHS compliant.
www.knuerr.com
Emerson Network Power Rack PDUs
Adaptive Rack PDU
TM
Liebert MPXTM
The Liebert MPXTM modular rack PDU system is particularly
impressive with its maximum flexibility, highest possible
availability and low operating costs. With the Liebert MPXTM
users can quickly and specifically react to new requirements
for power supply and rack management. The Liebert MPXTM
gives users the ability to dimension their rack PDU system so
that all current requirements are met first off. The system can
then be flexibly adjusted later on when new requirements
appear. The Liebert MPXTM builds on a design that is based
on a power supply/communication bus and on input/output
modules.
The Liebert MPXTM modular rack PDU consists of various
modules. The foundation stone is a busbar, which is responsible for the power and communication distribution to the
individual modules. The input power is routed via the MPX
Power Entry Module (MPX PEM) to the MPX system. Different
output modules (MPX Branch Receptacle Modules, MPX BRM)
are available according to requirements. Four different lines
can be set up depending on the equipment:
•
•
•
•
Liebert MPXTM Elementary
Liebert MPXTM Elementary Phase monitored
Liebert MPXTM Branch monitored
Liebert MPXTM Receptacle managed
These lines can also be mixed on a shared busbar, this being
one of the exceptional features of the Liebert MPXTM. Interfaces for the network communication, the sensors and/or the
local display are provided by the Liebert Rack PDU Card
(Liebert RPC) in the MPX PEM. The Liebert RPC Card enables
connection to an optional RPC Basic Display Module (RPC
BDM) to display the local status and alarms.
Emerson Network Power Rack PDUs
The Liebert MPXTM is provided as a separate, loosely packaged
module for on-site configuration by the user. The MPX was designed
especially for quick and easy configuration and re-configuration.
Preconfigured systems are also available when ordered as factoryinstalled Knürr rack enclosure systems.
Liebert MPXTM
Strong points
Highest possible security and
availability with:
- Redundant control electronics
power supply (with redundant
tapping of various phase in the
Power Entry Module)
- Fixed databus on the busbar
(making cable breaks a thing of
the past)
- With complete data tapping on
the PEM (without any additional
external monitoring devices)
- Additional neutral conductor
measurement
- Crest factor measurement (mains
quality evaluation, allowing power
supply failures to be identified
early on )
Maximum flexibility and scalability with:
- Configuration of all modules
according to their requirements
(including input module)
- “Hot-swappable” during running
operation
- Feed can be changed (singlephase up to three-phase, 16 up to
63 ampere)
- Mobile display for reading all
MPXTM data on the rack
- Optical display of the slot space
(easy server slot space identification
at the push of a button)
Ultimate high performance with:
- Power illustration up to 28 kVA
per bar and 55°C ambient temperature
- Only one IP address for up to 4
bars with 24 modules
- Plug and play for numerous sensors
- Extensive monitoring with a
measuring accuracy of +/- 1% up
to output level
- Module and sensor autodetect
function with operating software
- Lowest possible MPXTM system
power loss
Perfect for blade servers and
changing environments
Data centers work more and more
with high performance blade
servers and require more processor
power on low rack space; cabling
must be simplified; power consumption must be reduced.
With the MPXTM the data center
can quickly react to changes,
which is why our product is the
right choice for your infrastructure’s administration.
4UBUVTEJTQMBZ31$#%.
Can be easily positioned at the optimum spot for the
individual rack; even functions outside the rack. This
connected display can be mounted just as the user
wishes.
Emerson Network Power Rack PDUs
Liebert MPXTM PRC - Power Distribution Unit/Communication Bus
- The MPX PRC is the foundation stone of the
Liebert MPX PDU.
- Power and data transfer buses are integrated
fixed over the entire length of the MPX PRC.
- The MPX BRMs (output modules) and the MPX
PEM (power entry module) are fixed on the MPX
PRC and depending on the type take care of the
modules’ power feed, output, monitoring and
management.
Approvals
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova GS
Load rating
Max. current intensity: 3 x 63 A
Nominal voltage (L-N / L-L): 230 / 400 Vac
Supply schedule
1 Liebert MPXTM PRC - Power Distribution
Unit/Communication Bus
1 mounting set
Operating instructions
Material/ Finish
Busbars housing: Aluminum
Busbars: Copper
Databus: Gilded
Dimensions
Width: 68 mm
Height: 24 mm
Color
Housing: aluminum
L
DOS20153
W
H
U
Model
Order no.
UP
1035 68
24
23
1 PEM (220mm) + 3 BRM
MPXPRC-V1035XXX
1 unit
1880 68
24
42
1 PEM (220/266mm) + 6 BRM
MPXPRC-V1880XXX
1 unit
Liebert MPXTM – Input Module/Power Supply
DOS20153
Elementary and Monitored type:
- The MPX PEM is fixed on the MPX PRC and
provides the connection to the power supply.
- Cable is connected fixed, 3 m long
- With IEC60309 plug, 1Ph/N/PE 6h blue,
3Ph/N/PE 6h red
Material/ Finish
Housing: Aluminum
Cover: Sheet steel
Power contacts: Silvered
Databus contacts: Gilded (only Monitored
type)
Monitored type:
- The MPX PEM provides the connection to the
databus for the data communication.
- The MPX PEM has an installation slot into
which the RPC-1000 communication card can
be installed. (Not in the supply schedule)
- Provides the following measured values of the
phase inputs: real power, current, voltage, frequency and consumption.
- Power alarm functions for the individual phases
and their operating status are also supported.
- Further important features: Three displays
inform the user about the current status of
each individual input. An acoustic alarm is
activated with specific overload conditions.
Dimensions
Width: 75 mm
Height: 65 mm
Cable: 3 m
U
Color
Housing: Aluminum/RAL 9011 black
Approvals
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova GS
Supply schedule
1 MPX PEM - Power Entry Module incl.
connection cable
Operating instructions
L
W
H
Feed
Load rating
Type
220
75
65
Fixed
230Vac, max 32A
Elementary MPXPEM-EHAEXQ30
Order no.
UP
1 unit
220
75
65
Fixed
230/400Vac, max 16A
Elementary MPXPEM-EHAEXT30
1 unit
220
75
65
Fixed
230/400Vac, max 32A
Elementary MPXPEM-EHAEXR30
1 unit
266
75
65
Fixed
230/400VacC, max 63A
Elementary MPXPEM-EHBEXZ30
1 unit
220
75
65
Fixed
230Vac, max 32A
Monitored
MPXPEM-EHAXXQ30
1 unit
220
75
65
Fixed
230/400Vac, max 16A
Monitored
MPXPEM-EHAXXT30
1 unit
220
75
65
Fixed
230/400Vac, max 32A
Monitored
MPXPEM-EHAXXR30
1 unit
266
75
65
Fixed
230/400Vac, max 63A
Monitored
MPXPEM-EHBXXZ30
1 unit
Emerson Network Power Rack PDUs
Liebert MPXTM BRM - Output Module
- The MPX BRM takes care of the power distribution to the individual load
- Each module taps a phase; this is color-identified
on the module.
- All modules are protected against overload
with a 20A circuit breaker.
- Changing the modules during operation
enables a user-defined installation, without
having to shut down the Liebert MPX.
- Up to 3 BRM output modules can be installed on
a 1035 mm PRC busbar; up to 6 BRM output
modules can be installed on a 1880 mm PRC
busbar.
- The MPX BRMs have an LED-ID indicator, which
clearly identifies every module with a number.
- The modules are administered in the software
- Provides the following measured values:
power, current, voltage, apparent power, kWh,
frequency, power factor and crest factor
- Power alarm functions and the operating status
are supported
- The individual outputs can be switched on and
off remotely
Type E - Elementary:
- Module for power distribution via respective
outputs
DOS20153
Type B – Branch monitored:
- Module for power distribution via respective
outputs with measuring function on module
level
- The MPX BRMs have an LED-ID indicator, which
clearly identifies every module with a number.
- The modules are administered in the software
- Provides the following measured values:
power, current, voltage, apparent power, kWh
and power factor
- Power alarm functions and the operating status
are supported
Material/ Finish
Housing: Aluminum
Cover: Sheet steel
Power contacts: Silvered
Databus contacts: Gilded (only type B and R)
Dimensions
Width: 75 mm
Height: 65 mm
Color
Housing: Aluminum/RAL 9011 black
Approvals
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova GS
Supply schedule
1 MPXTM BRM Output Module
Operating instructions
Type R – Receptacle managed:
- Module for power distribution via respective
outputs with measuring function on module
level and output level
L
n
Outputs
Load rating
per output
Phase
tapping
Type
Order no.
UP
266
7
IEC320 Sheet F
10A
L1
E
MPXBRM-EEBC7N1N
1 unit
266
7
IEC320 Sheet F
10A
L2
E
MPXBRM-EEBC7N2N
1 unit
266
7
IEC320 Sheet F
10A
L3
E
MPXBRM-EEBC7N3N
1 unit
266
4
IEC320 Sheet J
16A
L1
E
MPXBRM-EEBC4O1N
1 unit
266
4
IEC320 Sheet J
16A
L2
E
MPXBRM-EEBC4O2N
1 unit
266
4
IEC320 Sheet J
16A
L3
E
MPXBRM-EEBC4O3N
1 unit
266
3
Schuko CEE 7/4
16A
L1
E
MPXBRM-EEBC3P1N
1 unit
266
3
Schuko CEE 7/4
16A
L2
E
MPXBRM-EEBC3P2N
1 unit
266
3
Schuko CEE 7/4
16A
L3
E
MPXBRM-EEBC3P3N
1 unit
266
6
IEC320 Sheet F
10A
L1
B
MPXBRM-EBBC6N1N
1 unit
266
6
IEC320 Sheet F
10A
L2
B
MPXBRM-EBBC6N2N
1 unit
266
6
IEC320 Sheet F
10A
L3
B
MPXBRM-EBBC6N3N
1 unit
266
4
IEC320 Sheet J
16A
L1
B
MPXBRM-EBBC4O1N
1 unit
266
4
IEC320 Sheet J
16A
L2
B
MPXBRM-EBBC4O2N
1 unit
266
4
IEC320 Sheet J
16A
L3
B
MPXBRM-EBBC4O3N
1 unit
266
3
Schuko CEE 7/4
16A
L1
B
MPXBRM-EBBC3P1N
1 unit
266
3
Schuko CEE 7/4
16A
L2
B
MPXBRM-EBBC3P2N
1 unit
266
3
Schuko CEE 7/4
16A
L3
B
MPXBRM-EBBC3P3N
1 unit
266
6
IEC320 Sheet F
10A
L1
R
MPXBRM-ERBC6N1N
1 unit
266
6
IEC320 Sheet F
10A
L2
R
MPXBRM-ERBC6N2N
1 unit
266
6
IEC320 Sheet F
10A
L3
R
MPXBRM-ERBC6N3N
1 unit
266
4
IEC320 Sheet J
16A
L1
R
MPXBRM-ERBC4O1N
1 unit
266
4
IEC320 Sheet J
16A
L2
R
MPXBRM-ERBC4O2N
1 unit
266
4
IEC320 Sheet J
16A
L3
R
MPXBRM-ERBC4O3N
1 unit
266
3
Schuko CEE 7/4
16A
L1
R
MPXBRM-ERBC3P1N
1 unit
266
3
Schuko CEE 7/4
16A
L2
R
MPXBRM-ERBC3P2N
1 unit
266
3
Schuko CEE 7/4
16A
L3
R
MPXBRM-ERBC3P3N
1 unit
Emerson Network Power Rack PDUs
Liebert RPC - 1000 Communication Card
DOS20153
- The Liebert RPC centralizes the Liebert MPX
local and remote administration.
- Administration via web and SNMP for systems
connected to the Ethernet.
- Also serves as the connection point for versatile support options and devices, such as the
display module (RPC BDM), various sensors
and connection to other Liebert MPX or Liebert
MPH systems, for example.
- Has RJ-45 ports for all connections and does
not require any special cabling.
- Supports 10 and 100 MBit Ethernet and provides
on-site firmware upgrade.
- Installed in an MPX PEM (input module) slot.
Technical data
Interfaces:
- RJ-45 LAN port (10/100 MBit) – for connecting to the local network (LAN) via an
Ethernet cable
L
W
H
U
- Expansion/administration port for local configuration using a computer/laptop, for
setting up a link-up of several PDUs (Liebert
MPX or MPH)
- Display port for connecting the RPC BDM
(display module)
- External sensor port for connecting optional
sensors
Supported technologies:
- Web support, provides Liebert MPX control
and management. Authorized users can view
status information via their network.
- SNMP support, provides Liebert MPX SNMP
management.
- Easy integration into Liebert Nform, Avocent
DSVIEW3 and Nagios
Supply schedule
1 RPC-1000 communication card
Operating instructions
Model
Order no.
UP
RPC-1000
1 unit
Liebert RPC BDM - 1000 Display Module
DOS20153
- Provides the local display of the monitored
data for all connected Liebert MPX and Liebert
MPH systems.
- Operated with the aid of a navigation switch.
- Connected via a cable with the Liebert RPC,
which provides the user the option of placing
the displays where they can be easily read in
accordance with the local space conditions.
- An individual display can be used for up to four
Liebert MPX or Liebert MPH PDUs, which are
connected to a PDU array.
L
W
H
U
Model
Note
The Display Module is not required for
operating the Liebert MPX or MPH, but it
itself requires the Liebert RPC-1000 (communication card)
Supply schedule
1 RPCBDM-1000 Display Module
1 2m power supply lead
1 mounting set
Operating instructions
Order no.
UP
RPCBDM-1000
1 unit
Emerson Network Power Rack PDUs
Liebert MPXTM/MPHTM Sensors
DOS20153
- The sensors are designed for tool-less installation in a Knürr Miracel Rack, but they can also
be installed in any other rack.
- “Fixed” type sensors are fixed to a cable.
- “Modular” type sensors can be connected with
the delivered cable.
- Are affixed to the RPC-1000 communication
card
- Several sensors can be connected in rows
(max. length: 20m)
- Are automatically displayed in the Liebert
MPX/MPH software
- Temperature measuring range: 5-55°C
- Accuracy: +/- 0.5°C
- Humidity measuring range: 10 – 95%
- Accuracy: +/- 3.5%
Note
The sensors are not required for operating
the Liebert MPX or MPH, but they require
the Liebert RPC-1000 (communication card)
Supply schedule
1 sensor with connection cable
Operating instructions
Cable length Type
Model
Order no.
3660
Fixed
Single temp. sensor
SN-Z01
1 unit
5180
Fixed
Triple temp. sensor
SN-Z02
1 unit
5180
Fixed
Triple temp. sensor + single humidity
SN-Z03
1 unit
2000
Modular
Single temp. sensor
SN-T
1 unit
2000
Modular
Triple temp. sensor + single humidity
SN-TH
1 unit
2000
Modular
2 x door contact - input module*
SN-2D
1 unit
2000
Modular
3 x digital input
SN-3C
1 unit
* Suitable door contact switch: Order no.: 06.108.115.9
UP
Emerson Network Power Rack PDUs
O rder Number s : Lieber t MPX™ Europe
Busbars
Input modules
Length 1035
MPXPRC-V1035XXX
Length 1880
MPXPRC-V1880XXX
1ph 32A fixed
MPXPEM-EHAEXQ30
3ph 16A fixed
MPXPEM-EHAEXT30
3ph 32A fixed
MPXPEM-EHAEXR30
3ph 63A fixed
MPXPEM-EHBEXZ30
MPXPEM-EHAXXQ30
MPXPEM-EHAXXT30
MPXPEM-EHAXXR30
MPXPEM-EHBXXZ30
Output modules:
Elementary
Output modules:
Branch monitored
Output modules:
Receptacle managed
IEC-C13 L1
MPXBRM-EEBC7N2N
IEC-C13 L3
MPXBRM-EEBC7N3N
IEC-C19 L1
MPXBRM-EEBC4O1N
IEC-C19 L2
MPXBRM-EEBC4O2N
IEC-C19 L3
MPXBRM-EEBC4O3N
Schuko L1
MPXBRM-EEBC3P1N
Schuko L2
MPXBRM-EEBC3P2N
Schuko L3
MPXBRM-EEBC3P3N
IEC-C13 L1
MPXBRM-EBBC6N1N
IEC-C13 L2
MPXBRM-EBBC6N2N
IEC-C13 L3
MPXBRM-EBBC6N3N
IEC-C19 L1
MPXBRM-EBBC4O1N
IEC-C19 L2
MPXBRM-EBBC4O2N
IEC-C19 L3
MPXBRM-EBBC4O3N
Schuko L1
MPXBRM-EBBC3P1N
Schuko L2
MPXBRM-EBBC3P2N
Schuko L3
MPXBRM-EBBC3P3N
IEC-C13 L1
MPXBRM-ERBC6N1N
IEC-C13 L2
MPXBRM-ERBC6N2N
IEC-C13 L3
MPXBRM-ERBC6N3N
IEC-C19 L1
MPXBRM-ERBC4O1N
IEC-C19 L2
MPXBRM-ERBC4O2N
IEC-C19 L3
MPXBRM-ERBC4O3N
Schuko L1
MPXBRM-ERBC3P1N
Schuko L2
MPXBRM-ERBC3P2N
Schuko L3
MPXBRM-ERBC3P3N
1xTemp.
SN-Z01
RPC-1000
Interface card
Sensors
Display ext.
MPXBRM-EEBC7N1N
IEC-C13 L2
3xTemp.
SN-Z02
3xT. + 1xHum
SN-Z03
1xTemp. Mod.
SN-T
Temp/Hum Mod.
SN-TH
2xDoor Mod.
SN-2D
3xInput Mod.
SN-3C
RPCBDM-1000
MPX
Elementary
MPX Elementary
Phase monitored
MPX
Branchmonitored
MPX
Receptaclemanaged
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Upgrade possible !
Order number
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Different combinations possible !
Emerson Network Power Rack PDUs
M a n a g e d Ra c k- PD U
TM
Liebert MPH TM
The Liebert MPH® Managed Rack PDU is a power supply system
with monitoring and control functions.
The Liebert MPH® monitors the current, voltage, kW and kWh
of the individual input phases, as well as the current per group
with the 32A variants. The individual outputs can be switched
on and off remotely depending on the type. Limit values, alarms
and status can be retrieved and set. The housing consists of a
robust sheet steel enclosure, so that the PDU can be easily
installed in a Knürr rack, or even into other enclosure systems.
The Liebert MPH can be installed vertically or horizontally (19”),
depending on the type. The PDU is delivered pre-installed with
the same communication card (RPC-1000) as the Liebert MPX®.
All Liebert MPX® external modules can therefore be connected
(e.g. sensors, display module). Up to 4 MPX/MPH can be connected as rack PDU array to consolidate the user’s IP connection
and the device monitoring.
Liebert MPHTM
Strong points
Liebert MPHTM
Control technology support
The monitored electrical parameters include: effective power,
current intensity, voltage and
accumulated energy or consumption. Capacity-oriented current
intensity threshold values enable
detailed rack PDU alarm signals.
Liebert MPHTM:
- The benefit for your data center:
Monitors electrical and environment
parameters with threshold values
and alarm management
- Controls access to the socket
power
- Controls and administers individual
sockets and/or groups of consumers
and devices
- Forecasts failure situations before
they occur and actively administers connected devices for
maximum operating time
Liebert MPHTM benefits: Flexibility
- A local display can be easily
mounted and adjusted to heavily
equipped and changing rack environments
- Mounting in 19” and 42 U rack
environments
- Form factor: vertical (0 U) and
rack mounting
- Compatible monitoring platform
for Liebert MPHTM and Liebert
MPXTM with seamless simultaneous
operation
- Individually positioned interface
for input network cable
Emerson Network Power Rack PDUs
Higher availability
- Controls and administers individual
sockets
- Forecasts overcurrent conditions
before critical phase
- Switches off redundant devices
with power failures to increase
availability and backup power
- Extended overload protection in
branch lines minimizes danger
with cascaded PDU overload
Extremely low operating costs
- Comprehensive control technology
in a cost-effective package
- The rack PDU array uses a shared
IP address for up to four racks
- PDUs, making installation quicker
and easier
- Energy and current measurement
provides data for maximizing the
data center’s current and cooling
infrastructure
- Energy efficient control technology
for sockets
Liebert MPHTM Rack PDU
- The Liebert MPH® Type M is a monitored
power distribution unit that monitors the
phase inputs.
- Measured per phase are: power, current, voltage
and consumption. The current is also monitored
per group (only 32A model).
- The Liebert MPH® Type C can also switch the
individual outputs on and off remotely.
- Integrated Liebert RPC-1000 communication
card enables remote monitoring and maintenance of MPH units.
- The RPC-1000 enables the interconnection of
several MPH or MPX units and connection of
the Liebert MPH® with the Liebert MPX® units
for monitoring and administration.
- The Liebert MPH® can be monitored directly
on-site with the RPC BDM-1000, an optional
display module that is connected directly with
the communication card. The monitoring unit
can be flexibly mounted on the rack.
L
DOS20153
Type Input values
Material/ Finish
Housing: Sheet steel extrusion
Dimensions
Width: 50 mm (vertical), 178 mm (19”)
Height: 80 mm (vertical), 44 mm (19”)
Color
Housing: RAL 7021 dark gray
Approvals
- CE label in accordance with Low Voltage
Directive 2006/95/EC
- EMC Directive 2004/108/EC
- GS
Supply schedule
1 Liebert MPH® Socket Strip (PDU)
1 mounting brackets
Operating instructions
Input plug
Outputs IEC320
Order no.
UP
438* M
230Vac, 16A
IEC320-Sheet I
9xSheet F
MPH-EBR09NXXO30
1 unit
438* M
230Vac, 32A
IEC60309 1ph/N/PE 6h
9xSheet F
MPH-EBR09NXXQ30
1 unit
1730 M
230Vac, 16A
IEC320-Sheet I
27xSheet F
MPH-EBV27NXXO30
1 unit
1730 M
230Vac, 16A
IEC320-Sheet I
21xSheet F/6xSheet J
MPH-EBV27NOXO30
1 unit
1730 M
230Vac, 32A
IEC60309 1ph/N/PE 6h
21xSheet F/6xSheet J
MPH-EBV27NOXQ30
1 unit
1730 M
230Vac, 32A
IEC60309 1ph/N/PE 6h
27xSheet F
MPH-EBV27NXXQ30
1 unit
1730 M
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
27xSheet F
MPH-EBV27NXXR30
1 unit
1730 M
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
21xSheet F/6xSheet J
MPH-EBV27NOXR30
1 unit
438* C
230Vac, 16A
IEC320-Sheet I
9xSheet F
MPH-ECR09NXXO30
1 unit
438* C
230Vac, 32A
IEC60309 1ph/N/PE 6h
9xSheet F
MPH-ECR09NXXQ30
1 unit
1730 C
230Vac, 16A
IEC320-Sheet I
27xSheet F
MPH-ECV27NXXO30
1 unit
1730 C
230Vac, 16A
IEC320-Sheet I
21xSheet F/6xSheet J
MPH-ECV27NOXO30
1 unit
1730 C
230Vac, 32A
IEC60309 1ph/N/PE 6h
21xSheet F/6xSheet J
MPH-ECV27NOXQ30
1 unit
1730 C
230Vac, 32A
IEC60309 1ph/N/PE 6h
27xSheet F
MPH-ECV27NXXQ30
1 unit
1730 C
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
27xSheet F
MPH-ECV27NXXR30
1 unit
1730 C
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
21xSheet F/ 6xSheet J
MPH-ECV27NOXR30
1 unit
* (19”)
Emerson Network Power Rack PDUs
Liebert MPXTM/MPHTM Sensors
DOS20153
- The sensors are designed for tool-less installation
in a Knürr Miracel Rack, but they can also be
installed in any other rack.
- “Fixed” type sensors are fixed to a cable.
- “Modular” type sensors can be connected with
the delivered cable.
- Are affixed to the RPC-1000 communication
card
- Several sensors can be connected in rows
(max. length: 20m)
- Are automatically displayed in the Liebert
MPX/MPH software
- Temperature measuring range: 5-55°C
- Accuracy: +/- 0.5°C
- Humidity measuring range: 10 – 95%
- Accuracy: +/- 3.5%
Note
The sensors are not required for operating
the Liebert MPX or MPH, but they require
the Liebert RPC-1000 (communication card)
Supply schedule
1 sensor with connection cable
Operating instructions
Cable lengthType
Model
Order no.
3660
Fixed
Single temp. sensor
SN-Z01
UP
1 unit
5180
Fixed
Triple temp. sensor
SN-Z02
1 unit
5180
Fixed
Triple temp. sensor + single humidity
SN-Z03
1 unit
2000
Modular
Single temp. sensor
SN-T
1 unit
2000
Modular
Triple temp. sensor + single humidity
SN-TH
1 unit
2000
Modular
2 x door contact - input module*
SN-2D
1 unit
2000
Modular
3 x digital input
SN-3C
1 unit
* Suitable door contact switch: Order no.: 06.108.115.9
Liebert RPC BDM - 1000 Display Module
DOS20153
- Provides the local display of the monitored
data for all connected Liebert MPX and Liebert
MPH systems.
- Operated with the aid of a navigation switch.
- Connected via a cable with the Liebert RPC,
which provides the user the option of placing
the displays where they can be easily read in
accordance with the local space conditions.
- An individual display can be used for up to four
Liebert MPX or Liebert MPH PDUs, which are
connected to a PDU array.
L
W
H
U
Model
Note
The Display Module is not required for
operating the Liebert MPX or MPH, but it
itself requires the Liebert RPC-1000 (communication card)
Supply schedule
1 RPCBDM-1000 Display Module
1 2m power supply lead
1 mounting set
Operating instructions
Order no.
UP
RPCBDM-1000
1 unit
Emerson Network Power Rack PDUs
Liebert MPXTM
Adaptive Rack PDU
Liebert MPHTM
Managed Rack PDU
Knürr DI-STRIP®
Basic Rack PDU
Emerson Network Power Rack PDUs
Basic Rack PDU
Knürr DI-STRIP®®
Knürr’s Basic Rack PDUs are the solution for every data center
looking for robust, economical and flexible rack concepts.
The Knürr DI-STRIP® product family meets the power distribution requirements of many IT applications and other areas.
Specially configured for the growing number of electronic
components in network switching racks or server racks. Available with the most diverse accessories, such as circuit
breakers, overvoltage protection, mains filter, master-slave
function, emergency off button, fault current circuit breaker,
local and remote power measurement, for example.
Knürr DI-STRIP® M:
The DI-STRIP M model monitors the
input current per phase locally. An
unbalanced load warning is also
shown on the display with 3ph PDUs.
The displays can be changed in 90°
steps with a selector switch.
Knürr DI-STRIP® RM:
The DI-STRIP RM model monitors the
input current per phase locally and
remote. Unbalanced load warning and
different threshold values can be set
and remotely forwarded.
1U
= 44.45 mm
19’’
m
465 m
m
483 m
1 DOS00291
4 DOS00365
Emerson Network Power Rack PDUs
Knürr DI-STRIP®
Strong points
1
Robust!
Protects the plug panel with high
casing edges.
2
Stability
High stability and torsional
strength provided with closed
sheet steel casing.
3
5 DOS00721
4
Electrical safety
Full power to all connected consumers with full-length brass
busbar.
Shock hazard-proof and low contact resistance with double spring
contacts.
19” installation
Optimum use of space with 19”
installation:
- With low height – 1 U (44.45 mm)
- With 45° positioning of the sockets
5
International compatibility
Numerous standard products in
accordance with international standards. Special models on request.
6
Flexibility
Plenty of room for movement with
2.5 m power supply cable.
Flexibility provided by standard
plug with dual earthing system.
7 DOS00366
8 DOS20131
9 DOS20134
7
Aesthetics
Appealing design with extruded
casing and design side panels in
visible area.
8
Cost-effective
Quick and easy mounting on the
rack extrusion.
9
Universal
1 and 3-phase systems.
10
Modularity
Socket strip modules can be easily
combined using plug-in connections.
10
Plug-in
Proven GST18 plug-in system for
connecting socket strip modules.
11
Certifications
Global approvals and certifications
are a quality feature.
9 DOS20134
10 DOS20142
10 DOS20144
Emerson Network Power Rack PDUs
Standard DIN 49 440
DI-STRIP® Classic
- Socket spacing: 100 mm
- With/without switch
Page 2.25
DOS00402
DI-STRIP® Compact
- Socket spacing: 50 mm
- With/without switch
Page 2.26
19’’
DOS00401
DI-STRIP® Protector
- User protection (FI)
- Circuit breaker (LS)
- User protection and circuit breaker (FI/LS)
- Equipment protection (BladePower/PizzaPower)
Page 2.27
DI-STRIP® Protector Emergency STOP
- User protection / circuit breaker (FI/LS)
- With emergency stop switch
Page 2.28
19’’
DOS00394
19’’
DOS00455
DI-STRIP® Power Cleaner
- Mains filter (MF)
Page 2.29
19’’
DOS00400
DI-STRIP® Safety Basic
Page 2.30
19’’
DI-STRIP® Safety Standard
- Overvoltage protection
DOS00397
DI-STRIP® Master Slave
- Automatic consumer switching
Page 2.32
DOS00366
DI-STRIP® Combi
- Automatic consumer switching with overvoltage protection
and mains filter
Page 2.32
DOS00399
DI-STRIP® GST18
Compact/Master Slave/Safety Basic/Safety Standard/IEC320
- Without cable for GST18 plug-in system (Wieland)
GST18 Accessories
DI-STRIP® M and DI-STRIP® RM
Page 2.34
DOS00679
Page 2.18
DOS80015
DI-STRIP® HighPower
19’’
Emerson Network Power Rack PDUs
Euro Plug System
Page 2.38
19’’
Page 2.41
Page 2.51
DOS00402
DOS00717
Page 2.42
19’’
DOS20155a
Page 2.43
19’’
19’’
DOS20065
Page 2.44
Three-Phase Current
Plug-In System
Swiss Standard
DOS00401
DOS00457
Page 2.24
UTE Standard
Page 2.52
19’’
Page 2.23
DOS20074
DOS20121
Page 2.53
Page 2.25
DOS00719
DOS20153a
19’’
DOS20059
Page 2.35
19’’
DOS20108
Page 2.35
DOS20110
Page 2.45
19’’
DOS00400
19’’
Page 2.46
19’’
DOS00397
Page 2.48
Page 2.53
19’’
DOS00720
19’’
DOS00464
Page 2.49
DOS00399
Page 2.35
Page 2.50
Page 2.36
DOS20112
DOS00463
DOS20103
Page 2.18
Page 2.23
DOS80001
Page 1.21
DOS80015
Page 2.21
19’’
Emerson Network Power Rack PDUs
Knürr DI-STRIP® RM
- Real RMS value display for the alternating current
per phase
- LCD display rotation in 90° steps
- Display bright/dark switchover
- Warning display for unbalanced load
- Load changes signaling
- Automatic background light reduction
DOS80002
Material/ Finish
- PizzaPower model:
Housing: Sheet steel, zinc-passivated,
powder-coated
- Other models:
Housing: closed sheet steel extrusion,
zinc-passivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO
(UL94), recyclable
Data interface:
- The plug strip can be integrated into the network
via an RJ45 plug.
- Access is possible without special software via
a remote browser.
- Three variable limit values and a warning for
unbalanced loads can be specified.
- The module enables access for up to 5 users or
administrators; access is password-protected.
- The software displays the name and place of
the PDU; this information can be entered by an
administrator.
- The user can specify a static IP address or
access using DHCP.
- Firmware updates can be made via a web
browser.
- Supported protocols: HTTP, SNMP (Traps, SET,
GET), Syslog
Dimensions
Width: 84 mm (PizzaPower), 44.4 mm (others)
Height: 60 mm (PizzaPower), 44.4 mm
(others)
Color
PizzaPower model:
Housing: RAL 9005 black
Other models:
Housing: RAL 7035 light gray
Plastic parts: RAL 7021 dark gray
Approvals
l in accordance with low voltage guideline
2006/95/EWG
- EMC Directive 2004/108/EC
- GS
Supply schedule
1 socket strip (PDU) with remote ampere meter
1 mounting brackets
Operating instructions
L
Type
Input values
Input plug
Outputs IEC60320
Sheet F
Sheet J
Order no.
UP
Schuko
733 DI-STRIP® Compact RM 8
230Vac, 16A
Schuko CEE 7/4
8
03.307.008.1
1 unit
1183 DI-STRIP® Compact RM 17
230Vac, 16A
Schuko CEE 7/4
17
03.307.017.1
1 unit
633 IEC320 RM9
230Vac, 16A
Schuko CEE 7/4
9
03.607.009.1
1 unit
933 IEC320 RM18
230Vac, 16A
Schuko CEE 7/4
18
03.607.018.1
1 unit
1133 DI-STRIP® TriplePower RM
230/400Vac, 16A
IEC60309 3ph/N/PE 6h
18
03.607.825.1
1 unit
1833 DI-STRIP® TriplePower RM
230/400Vac, 16A
IEC60309 3ph/N/PE 6h
45
03.607.845.1
1 unit
1233 DI-STRIP® TriplePower RM
230/400Vac, 16A
IEC60309 3ph/N/PE 6h
18
6
03.607.824.1
1 unit
1833 DI-STRIP® TriplePower RM
230/400Vac, 16A
IEC60309 3ph/N/PE 6h
36
6
03.607.842.1
1 unit
1111 DI-STRIP® PizzaPower® RM
230Vac, 32A
IEC60309 1ph/N/PE 6h
24
03.637.023.1
1 unit
871 DI-STRIP® PizzaPower® RM
230Vac, 32A
IEC60309 1ph/N/PE 6h
12
4
03.637.016.1
1 unit
1168 DI-STRIP® PizzaPower® RM
230Vac, 32A
IEC60309 1ph/N/PE 6h
21
4
03.637.025.1
1 unit
563 DI-STRIP® PizzaPower® RM
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
6
03.637.006.1
1 unit
995 DI-STRIP® PizzaPower® RM
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
6
12
03.637.018.1
1 unit
1022 DI-STRIP® PizzaPower® RM
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
21
03.637.021.1
1 unit
1157 DI-STRIP® PizzaPower® RM
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
18
6
03.637.024.1
1 unit
1751 DI-STRIP® PizzaPower® RM
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
36
6
03.637.042.1
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® M
- With big transparent LCD display
- Effective value display of alternating currents
per phase (1-phase or 3-phase, depending on
model)
- LCD display rotation in 90° steps
- Unbalanced-load warning display with 3-phase
model
- Load changes signaling
- Automatic background light reduction
- Cable: 4m H05VV—F 5 G 4mm² (PizzaPower M)
- Cable: 2.5m H05VV-F 5 G 2.5mm² (TriplePower M)
- Cable: 2.5m H05VV-F 3G 1.5mm² (DI-STRIP
Compact M, DI-STRIP IEC320 M)
DOS80002
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC:
EN61326-1, EN61000-3-2, EN61000-3-3
- FCC Class B
- CSA NRTL (PizzaPower m, TriplePower M,
IEC320 M)
- CB-Scheme (TriplePower M, DI-STRIP compact
M, IEC320M, ampere meter GST18i)
Color
PizzaPower M model:
Housing: RAL 9005 black
Other models:
Housing: RAL 7035 light gray
Plastic parts: RAL 7021 dark gray
Material/ Finish
PizzaPower® model:
Housing: Sheet steel, zinc-passivated, powdercoated
Other models:
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Supply schedule
1 socket strip with ampere meter
2 mounting brackets
2 19” mounting brackets (with 19” installation
option)
Note
- Other models (e.g. Sheet J outputs) on
request
L
Type
Input values
Input plug
Outputs IEC60320
Sheet F
Sheet J
Order no.
UP
Schuko
483 DI-STRIP® PizzaPower® M
230Vac, 32A
IEC60309 1ph/N/PE 6h
7
03.636.007.1
1 unit
933 DI-STRIP® PizzaPower® M
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
21
03.636.021.1
1 unit
1033 DI-STRIP® TriplePower® M
230/400Vac, 16A
IEC60309 3ph/N/PE 6h
21
03.606.821.1
1 unit
1833 DI-STRIP® TriplePower® M
230/400Vac, 16A
IEC60309 3ph/N/PE 6h
45
03.606.845.1
1 unit
1133 DI-STRIP® TriplePower® M
230/400Vac, 16A
IEC60309 3ph/N/PE 6h
18
6
03.606.824.1
1 unit
1733 DI-STRIP® TriplePower® M
230/400Vac, 16A
IEC60309 3ph/N/PE 6h
36
6
03.606.842.1
1 unit
483 DI-STRIP® Compact M
230Vac, 32A
Schuko
03.306.006.1
1 unit
483 DI-STRIP® IEC320 M
230Vac, 16A
Schuko
03.606.009.1
1 unit
233 DI-STRIP® Ampere meter
230Vac, 16A
GST18
03.606.200.1
1 unit
6
9
Emerson Network Power Rack PDUs
Knürr DI-STRIP®
HighPower ®®
The Knürr DI-STRIP® HighPower is a solution for every data
center with high power requirements and low space in the
rack. The special shape enables space-saving installation in the
rack. This means free access to the servers, even with 600 mm
wide racks. Maintenance of the servers (e.g. power supply
changes) is possible at no further expense.
The Knürr DI-STRIP® product family meets the power distribution requirements of many IT applications and other areas.
Specially configured for the growing number of electronic
components in network switching racks of server racks. The
DI-STRIP® HighPower is available with and without remote
power measurement (DI-STRIP® HighPower RM).
Emerson Network Power Rack PDUs
Knürr DI-STRIP® HighPower
Strong points
Flexibility
With or without remote power
measurement. Easy expansion in
the rack with tool-less installation.
3 m power cable for more spatial
flexibility.
RM model
Current values can be read via a big
transparent LCD display.
Rotating display in 90° steps; the
display can always be read the
same regardless of the installation
direction.
The power measurement module
can be integrated into different
management programs via different
protocols (SNMP, http, Syslog).
High availability
Meets the strictest EMC requirements with radiation and irradiation
interference. Robust and stable with
a closed sheet steel housing.
Reliable, robust solution.
Extensive certification in acc. with
international standard.
RM model:
Different threshold values can be
flexibly specified; power values can
therefore be monitored and load
drops can be signaled.
With 3-phase PDUs the unbalanced
load can be monitored, which
means the neutral conductor is
protected from overloads.
Low operating costs
Especially flat housing extrusion,
providing full accessibility to the
19” level with 600 mm wide server
racks. Server power supply changes
are very quick and easy.
Quick and easy installation on the
rack requires minimum space and
shorter installation time.
RM model:
Automatic background light reduction extends the display’s service
life and reduces power loss.
Knürr DI-STRIP® HighPower
DOS20153
- Flat design provides access to the 19” level,
even with 600 mm wide racks
– individual backup for outputs (groups with 10 A)
- Outputs divided into groups with max. 20 A
per group
- Modular expansion in the rack with tool-less
PDU installation
Dimensions
Width: 134 mm
Height: 47 mm
Cable: 3 m
Additional function for HighPower RM type
(remote metered)
- With big transparent LCD display
- Effective value display of alternating current
- LCD display rotation in 90° steps
- Display can be switched bright or dark
- Load changes signaling - Automatic background
light reduction
- See DI-STRIP RM for technical description for
data interface
Approvals
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- GS
Material/ Finish
Housing: Sheet steel, zinc-passivated, powdercoated
L
Type
Input values
Input plug
Color
Housing: RAL 9005 black
Supply schedule
1 socket strip (PDU)
1 integrated remote ampere meter (only
HighPower RM)
2 mounting brackets
Operating instructions
Outputs IEC60320
Sheet F
Sheet J
Order no.
UP
Schuko
540
DI-STRIP® HighPower
230Vac, 32A
IEC60309 1ph/N/PE 6h
20
4
03.632.100.8
1 unit
850
DI-STRIP® HighPower
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
6
12
03.632.102.8
1 unit
540
DI-STRIP® HighPower RM
230Vac, 32A
IEC60309 1ph/N/PE 6h
20
4
03.632.200.8
1 unit
850
DI-STRIP® HighPower RM
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
6
12
03.632.202.8
1 unit
Emerson Network Power Rack PDUs
Three Phase Knürr DI-STRIP®
TriplePower ®®
The TriplePower ® name represents the performance of our
latest development. The DI-STRIP® TriplePower® supplies
network racks with three times the normal power. This
requirement is generated by the increasingly higher packing
densities and constantly rising energy requirements in racks,
which are often caused by aptly named “Blade Servers” or 1 U
“Pizza Servers”, more than 40 of which can be integrated into
a Knürr Miracel rack.
The DI-STRIP® TriplePower® uses a classic 3-phase feed with
3x16A, which it optimally distributes throughout the whole
rack. The 23 U and 41 U standard lengths cover the entire rack
height range of the Knürr Smaract2 and Miracel rack families.
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side de piece
Design side piece
Suitable for 19” installation
Child-safe,
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
DOS20148
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
DOS20149
In the maximum configuration level, up to 48 users can
be connected to a DI-STRIP®
TriplePower® (Euro socket
strip). With redundant feed,
96A can consequently be provided in a 19” rack with only
two DI-STRIP® TriplePower®.
Emerson Network Power Rack PDUs
Knürr DI-STRIP® TriplePower®
Strong points
1
Cost-Effective
Quick and easy mounting on the
rack extrusion.
Cost reduction in installation and
wiring.
2
Supply
- 3x16A as standard
- Ideal for implementing redundancy (e.g. 96 A)
1 DOS20131
3
At a glance
Phase assignment color coding (L1,
L2, L3).
4
Installation
Optimum distribution over the
entire rack height
(standard: 23 U and 41 U).
3 DOS20126
Technical alternatives
- For 3-phase GST18 system (see
page 2.36).
2 DOS20147
4 DOS20129
DI-STRIP® TriplePower® Euro Plug-In System, IEC 320
With cable
- Cable: H05VV-F 5 G 2.5 mm2
- Cable: 2.5 m (optional with IEC60309 plug,
3Ph/N/PE 6h)
- Easy mounting on the rack extrusion
- 3x16A feed as standard
- Ideal for implementing redundancy (e.g. 96 A
with redundant feed)
- Unmistakable phase assignment color-coding
- Optimum distribution over the entire rack
height (23 U and 41 U)
- Alternative for 3-phase GST18 system (see
page 170)
DOS20126
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Dimensions
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
L
S
n
F1
19”
Input values
Input plug
24
1833
48
1033
24
1833
48
1133
24
1733
42
483
6
•
•
•
•
•
•
• •
Color
Housing: RAL 7035 light gray
Plastic parts: RAL 7021 dark gray
Load rating
100-240/173-415 Vac
Input: 3x 16 A
Output: 10 A (Sheet F)
Output: 16 A (Sheet J)
Approval symbols for IEC 320 3-way Euro
combinations
VDE, UR, CSA
Supply schedule
1 socket strip
2 mounting brackets
Outputs IEC60320
Sheet F
1033
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- CSA NRTL/C
Order no.
UP
Sheet J
230/400Vac, 16A
IEC60309 3ph/N/PE 6h
24
03.600.024.1
1 unit
230/400Vac, 16A
IEC60309 3ph/N/PE 6h
48
03.600.048.1
1 unit
230/400Vac, 16A
Open end
24
03.600.824.1
1 unit
230/400Vac, 16A
Open end
48
03.600.848.1
1 unit
230/400Vac, 16A
IEC60309 3ph/N/PE 6h
18
6
03.600.524.1
1 unit
230/400Vac, 16A
IEC60309 3ph/N/PE 6h
36
6
03.600.542.1
1 unit
230/400Vac, 16A
IEC60309 3ph/N/PE 6h
6
03.600.506.1
1 unit
Emerson Network Power Rack PDUs
Thr ee Phase Knürr DI-STRIP®
BladePower ®®
PizzaPower ®®
A new generation of the power distribution units of the
DI-STRIP® range now ensures even more power: BladePower®
and PizzaPower® for fail-safe power supply distribution in
network racks.
Increasingly higher packing densities and therefore constantly
increasing energy requirements in server racks caused by blade
servers or 1 U pizza servers will now be handled electrically.
Up to 35 kW dissipated heat can be removed from modern
CoolTherm® server racks But how is the necessary power supplied into the rack, which can cause such power losses?
The PDUs (3x32 A) optimally distribute the required power over
the entire rack, with connection of up to 21 consumers possible
in the highest configuration level. 192 A can be supplied to the
rack with redundant feed.
Knürr DI-STRIP®
Strong points
Cost-Effective
Quick and easy installation on the
server rack’s extrusion.
Costs reduction with mounting
and wiring.
Supply
- Single-phase 32 A and three-phase
32 A.
- 22 kVA
- Ideal for providing redundancy
(e.g. 192 A)
Crystal clear assignment
Unmistakable phase assignment
color-coding
(L1, L2, L3).
Installation
Optimum distribution of blade
center and pizza server supply with
easy power distribution unit (PDU)
installation.
Availability
Prevention of “Single Point of Failure”
with individual fusing.
Certification
Knürr DI-STRIP® BladePower®
Technical data
- EC 320 sockets (10 A and 16 A).
- Individually fused via thermal circuit breaker
that can be reset in acc. with IEC 60934
- Cable: H05VV-F 5 G 4 mm2
- Cable: 4 m
- With IEC60309 plug, 1Ph/N/PE 6h blue,
3Ph/N/PE 6h red
DOS20153
Material/ Finish
Housing: Sheet steel, zinc passivated, powdercoated
Color
Housing: RAL 9005 black
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
L
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Conversion:
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
S
n
F1
375
5
740
15
375
5
740
15
19”
Load rating
100-240 / 173-415 Vac
Input: 1x32 A or 3x32 A
Output: 10 A / 16 A
Supply schedule
1 socket strip (PDU)
2 mounting brackets
1 19” mounting bracket (additional with
19” installation option)
Operating instructions
Dimensions
Height: approx. 60 mm
Housing width: 84 mm
DOS20155
Approvals
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova GS
- CSA NRTL/C (only without plug)
Plug
• • •
•
•
• •
•
Model
Order no.
UP
BladePower® PDU 1x 32 A
03.630.005.1
1 unit
BladePower® PDU 3x 32 A
03.630.015.1
1 unit
BladePower® PDU 1x 32 A
03.630.805.1
1 unit
BladePower® PDU 3x 32 A
03.630.815.1
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® PizzaPower®
Technical data
- Individually fused via thermal circuit breaker
that can be reset in acc. with IEC 60934
- Cable: H05VV-F 5 G 4 mm2
- Cable: 4 m
- With IEC60309 plug, 1Ph/N/PE 6h blue,
3Ph/N/PE 6h red
DOS20158
Material/ Finish
Housing: Sheet steel, zinc passivated, powdercoated
Dimensions
Height: approx. 60 mm
Housing width: 84 mm
Height with cable: approx. 176 mm
Color
Housing: RAL 9005 black
DOS20159
L
S
n
F1
19”
Input values
Input plug
7
400
7
720
16
960
24
1017
25
933
21
933
21
408
6
939
21
1362
36
1002
24
•
•
•
•
•
•
•
•
•
•
•
Load rating
100-240 / 173-415 Vac
Input: 1x32 A or 3x32 A
Output: 10 A (Sheet F)
Output: 16 A (Sheet J)
Supply schedule
1 socket strip (PDU)
2 mounting brackets
1 19” mounting bracket
(additional with 19 installation option)
Operating instructions
Outputs IEC60320
Sheet F
400
Approvals
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova GS
- CSA NRTL/C (only without plug)
Order no.
UP
Sheet J
230Vac, 32A
IEC60309 1ph/N/PE 6h
7
03.631.007.1
1 unit
230Vac, 32A
Open end
7
03.631.807.1
1 unit
230Vac, 32A
IEC60309 1ph/N/PE 6h
12
230Vac, 32A
IEC60309 1ph/N/PE 6h
24
230Vac, 32A
IEC60309 1ph/N/PE 6h
21
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
21
230/400Vac, 32A
Open end
21
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
9
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
36
230/400Vac, 32A
IEC60309 3ph/N/PE 6h
18
4
4
03.631.124.1
1 unit
03.631.240.1
1 unit
03.631.214.1
1 unit
03.631.021.1
1 unit
03.631.821.1
1 unit
6
03.631.006.1
1 unit
12
03.631.912.1
1 unit
03.631.360.1
1 unit
03.631.186.1
1 unit
6
Knürr DI-STRIP® Classic
Standard DIN 49 440
- Optionally with lit switch, 2-pole switching
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Optionally with Euro plug, IEC320 for UPS
application
DOS00403
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94)
Internal conductor: full-length busbar, brass
DOS00260
DOS00261
With switch
Color
RAL 7035 light gray
Load rating
100-240 Vac/16 A
Dimensions
Socket spacing: 24 mm 100 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Supply schedule
1 socket strip
2 mounting brackets
Without switch
L
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
- VDE
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
n
F1
1783
S
17
1383
13
983
9
583
5
•
•
•
•
•
•
•
•
1733
1333
933
533
•
•
•
•
16
12
8
4
F2
19”
Safe
Model
Order no.
UP
03.300.067.1
1 unit
03.300.063.1
1 unit
03.300.059.1
1 unit
03.300.055.1
1 unit
With switch
03.302.066.1
1 unit
With switch
03.302.062.1
1 unit
With switch
03.302.058.1
1 unit
With switch
03.302.054.1
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Compact
Standard DIN 49 440
DOS00401
DOS00262
With switch
Without switch
DOS20021
With switch
Without switch
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
- VDE
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
With switch
DOS20020
DOS00263
- Optionally with lit switch, 2-pole switching
- 19” installation option (with length 483 mm)
- 2 versions: Standard side panel or Design side
panel
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
- Optionally with Euro plug, IEC320 for UPS
applications
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
L
n
F1
883
15
•
732
11
683
11
532
7
532
7
483
7
483
8
382
4
382
4
333
4
883
732
683
532
532
483
S
•
•
•
•
•
•
483
382
382
333
14
•
•
•
•
10
10
•
6
6
6
7
•
•
•
•
•
•
3
3
3
•
F2
19”
Color combination
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .6:
Housing: RAL 2003 pastel orange
Plastic parts: RAL 7035 light gray
Load rating
100-240 Vac/16 A
Supply schedule
1 socket strip
2 mounting brackets
Safe
Model
Order no.
UP
03.300.015.x
1 unit
03.300.111.x
1 unit
03.300.011.x
1 unit
03.301.107.x
1 unit
03.300.107.x
1 unit
03.300.007.x
1 unit
03.300.008.1
1 unit
03.301.104.x
1 unit
03.300.104.x
1 unit
03.300.004.x
1 unit
With switch
03.302.014.x
1 unit
With switch
03.302.110.x
1 unit
With switch
03.302.010.x
1 unit
With switch
03.303.106.x
1 unit
With switch
03.302.106.x
1 unit
With switch
03.302.006.x
1 unit
With switch
03.302.007.1
1 unit
With switch
03.303.103.x
1 unit
With switch
03.302.103.x
1 unit
With switch
03.302.003.x
1 unit
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Knürr DI-STRIP® Compact UPS
Standard DIN 49 440
L
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
S
n
F1
19”
Input values
Input plug
Outputs
Order no.
Schuko CEE7/4
UP
483
8
•
•
ICE60320 Sheet E 8
03.300.308.1
1 unit
8
•
•
230Vac, 10A
483
230Vac, 16A
ICE60320 Sheet I 8
03.300.408.1
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Protector FI
Standard DIN 49 440
DOS20065
DOS00264
Protector FI
RCCB for user protection
- Protection with indirect contact as error
protection by switching off with inadmissible
high contact voltage through contact with
electrical equipment
- Protection with direct contact as back-up
protection
- Residual operating current Ig = 10 mA for
alternating and pulsating direct fault current
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
With fault current circuit breaker
With fault current circuit breaker
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Dimensions
Socket spacing: 24 mm 50 mm
Height: 78 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combination
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Load rating
100-240 Vac/16 A
Supply schedule
1 socket strip
2 mounting brackets
L
n
F1
883
S
13
683
9
483
5
•
•
•
F2
19”
Safe
Model
•
Order no.
UP
03.304.013.1
1 unit
03.304.009.1
1 unit
03.304.005.1
1 unit
Knürr DI-STRIP® Protector LS
Standard DIN 49 440
DOS00692
DOS00264
Protector circuit breaker
- Circuit breaker for overload and short circuit
- Protects cables and feeds with rapid
switching off with short circuit and defined
delayed cutoff with overload
- Circuit breaker: 16 A
- Tripping characteristic, type B, 2-pole
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
With circuit breaker
With circuit breaker
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Dimensions
Socket spacing: 24 mm 50 mm
Height: 78 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
- VDE
Color combination
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Load rating
100-240 Vac/16 A
Supply schedule
1 socket strip
2 mounting brackets
L
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
n
F1
883
S
13
683
9
483
5
•
•
•
F2
19”
•
Safe
Model
Order no.
UP
03.308.013.1
1 unit
03.308.009.1
1 unit
03.308.005.1
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Protector FI / LS
Standard DIN 49 440
Protector FI / LS
- Fault current switch and circuit breaker
- Provides a combination of user, overload
and short circuit protection
- Residual operating current Ig = 30 mA for
alternating and pulsating direct fault
current
- Circuit breaker: 16 A
- Tripping characteristic, type B, 2-pole
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
DOS00693
DOS00264
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Dimensions
Socket spacing: 24 mm 50 mm
Height: 78 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combination
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Load rating
100-240 Vac/16 A
Supply schedule
1 socket strip
2 mounting brackets
L
n
F1
883
S
13
683
9
483
5
•
•
•
F2
19”
Safe
Model
•
Order no.
UP
03.310.013.1
1 unit
03.310.009.1
1 unit
03.310.005.1
1 unit
Knürr DI-STRIP® Protector Emergency STOP
Standard DIN 49 440
DOS20059
Classic with
emergency stop switch
- With 2-pole emergency stop switch for user
protection
- For protecting operating personnel
- For manual emergency switching off of the
connected consumers
- Phase and neutral conductors are safely separated
- Switch must be specifically unlocked to restart
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
DOS00486
Dimensions
Socket spacing: 24 mm Classic: 100 mm,
Compact: 50 mm
Protector with
emergency stop switch
Height: 101 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Approvals/ certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
- VDE
Color combinations
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Load rating
100-240 Vac/16 A
Supply schedule
1 socket strip
2 mounting brackets
DOS00487
L
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
n
F1
683
10
483
6
•
•
1333
12
933
S
8
•
•
F2
19”
•
Safe
Model
Order no.
UP
Compact
03.326.010.1
1 unit
Compact
03.326.006.1
1 unit
Classic
03.326.062.1
1 unit
Classic
03.326.058.1
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Protector Emergency Stop FI / LS
Standard DIN 49 440
- With 2-pole emergency stop switch for user
protection
- For protecting operating personnel
- For manual emergency switching off of the
connected consumers
- Phase and neutral conductors are safely separated
- Switch must be specifically unlocked to restart
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
DOS00456
DOS00488
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Dimensions
Socket spacing: 24 mm Compact: 50 mm
Height: 101 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
L
S
683
n
F1
8
•
F2
19”
Safe
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combinations
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Additionally:
With 2-pole fault current switch and circuit
breaker
Provides a combination of user, overload
and short circuit protection
Load rating
100-240Vac/16 A
Supply schedule
1 socket strip
2 mounting brackets
Model
Order no.
UP
03.328.008.1
1 unit
Knürr DI-STRIP® Power Cleaner
Standard DIN 49 440
- High-frequency glitches are generally caused
by switching processes in an operation from
100 kHz to 5MHz. This high-frequency rate
overloads the mains frequency and affects
adjacent electronic equipment. The mains
filter attenuates this high-frequency rate.
- The attenuation behavior is harmonized with
the typical interference spectrum.
- The mains filter works in both directions. This
means that glitches from the equipment to the
socket strip are also filtered from the mains.
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
DOS20061
DOS00266
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
L
n
F1
883
S
13
683
9
483
5
•
•
•
F2
19”
•
Safe
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combination
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .6:
Housing: RAL 2003 pastel orange
Plastic parts: RAL 7035 light gray
Technical data
Nominal voltage: max. 250 Vac, 50 Hz
Nominal current: max. 16 A
Filter in acc. with VDE 0565-3 (EN 60939-1)
Supply schedule
1 socket strip
2 mounting brackets
2 19” mounting bracket (additional with
19” installation option)
Model
Order no.
UP
03.312.013.x
1 unit
03.312.009.x
1 unit
03.312.005.x
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Safety Basic
Standard DIN 49 440
DOS20068
DOS00306
DOS00270
With overvoltage protection
With overvoltage protection
With overvoltage protection
- For protecting against transient overvoltages
from the mains, which, for example, are
caused by switching machines on and off.
- With critical overvoltages the mains is separated.
- Once the safety arrester has been triggered the
green function display goes out.
- The socket strip can then no longer be used.
Send the socket strip to the manufacturer for
the safety arrester to be replaced!
The safety effect of the type 3 test category
and requirements category “D” is to protect
the equipment, i.e. precision protection.
The protection devices of the test and requirements categories 1 and 2 and B and C must be
pre-connected in the building installation to
ensure optimum protection.
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
S
n
732
10
683
10
532
6
532
6
483
6
432
4
432
4
383
4
F1
•
•
•
F2
19”
Safe
•
•
•
•
•
•
•
Color combination
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .6:
Housing: RAL 2003 pastel orange
Plastic parts: RAL 7035 light gray
Technical data
Test category: Type 3
- In acc. with DIN EN 61643-11
Requirements class: D
- In acc. with VDE 0675-6
Mains voltage: 230 VAC
Nominal current: max. 16 A
Cut-off discharge current (8/20 μs): 10 kA
Response time: ‹ 25 ns
Protection level
(with 100 A varistor peak current):
- L with respect to N: ‹ 800 V
- L/N with respect to PE: ‹ 1500 V
Supply schedule
1 socket strip
2 mounting brackets
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
L
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
•
Model
Order no.
UP
03.316.110.1
1 unit
03.316.010.x
1 unit
03.317.106.1
1 unit
03.316.106.1
1 unit
03.316.006.x
1 unit
03.317.104.1
1 unit
03.316.104.1
1 unit
03.316.004.1
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Safety Standard
Standard DIN 49 440
DOS20069
DOS00307
With overvoltage protection
and mains filter
With overvoltage protection
and mains filter
DOS00271
- The “Safety Standard” models consist of a
combined overvoltage protection/mains filter
element.
- For protecting against transient overvoltages
from the mains, which, for example, are
caused by switching machines on and off.
- With critical overvoltages the mains is separated.
- Once the safety arrester has been triggered the
green function display goes out. The socket
strip can then no longer be used. Send the
socket strip to the manufacturer for the safety
arrester to be replaced!
- The safety effect of the type 3 test category
and requirements category “D” is to protect
the equipment, i.e. precision protection.
The protection devices of the test and requirements categories 1 and 2 and B and C must be
preconnected in the building installation to
ensure optimum protection.
- High-frequency glitches are generally caused
by switching processes in an operation from
100 kHz to 5MHz.
- This high-frequency rate overloads the mains
frequency and affects adjacent electronic
equipment. The mains filter attenuates this
high-frequency rate.
- The attenuation behavior is harmonized with
the typical interference spectrum.
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
L
S
n
F1
883
•
•
•
•
•
•
•
13
•
732
732
683
532
532
483
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
9
9
9
•
5
5
5
•
F2
19”
•
•
•
•
Safe
•
•
•
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combination
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .6:
Housing: RAL 2003 pastel orange
Plastic parts: RAL 7035 light gray
Technical data
Mains voltage: 230 VAC
Nominal current: max. 16 A
Cut-off discharge current (8/20 μs): 10 kA
Response time: ‹ 25 ns
Protection level
(with 100 A varistor peak current):
- L with respect to N: ‹ 800 V
- L/N with respect to PE: ‹ 1500 V
Overvoltage protection
- Test category: Type 3
in acc. with DIN EN61643-11
- Feature class: D
In acc. with VDE 0675-6
Mains filter
- In acc. with VDE 0565 (EN 60939)
Supply schedule
1 socket strip
2 mounting brackets
Model
Order no.
UP
With switch
03.318.013.x
1 unit
With switch
03.319.109.x
1 unit
With switch
03.318.109.x
1 unit
With switch
03.318.009.x
1 unit
With switch
03.319.105.x
1 unit
With switch
03.318.105.x
1 unit
With switch
03.318.005.x
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Master Slave
Standard DIN 49 440
DOS20070
DOS00268
With master-slave module
With master-slave module
- If the master equipment is switched, the slave
sockets are also switched (together, with a
short delay to the master). This means convenient switching on and off of several hard to
access devices. Switching thresholds can be set
from outside via potentiometer.
- Note:
- The master equipment power consumption
must be continuously above the switchingon threshold. When switching off the master
equipment, the power consumption must fall
below the switching-off threshold.
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
L
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
S
n
F1
9
483
5
•
•
F2
19”
•
Color combination
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Load rating
Max. 250 Vac/16 A
Technical data
Switching threshold setting range
On: 20 mA - 200 mA
(approx. 55 mA delivery status)
Off: 16 mA - 160 mA
(approx. 44 mA delivery status)
Switching delay: 550 ms +/- 20 %
Electronic module: 2-pole switching
Supply schedule
1 socket strip
2 mounting brackets
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
683
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Safe
Model
Order no.
UP
03.314.009.1
1 unit
03.314.005.1
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Combi
Standard DIN 49 440
DOS00325
With master-slave overvoltage
protection and mains filter
- Master-slave with overvoltage protection and
mains filter
- Automatic consumer switching
- Combines Master Slave
(page 7.16) and Safety Standard functions
(Page 7.15)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
DOS00272
DOS00273
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
With master-slave overvoltage
protection and mains filter
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
L
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
S
n
782
9
733
9
582
5
582
5
533
5
F1
•
•
F2
19”
Safe
•
•
•
•
Color combination
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Technical data
Overvoltage protection and mains filter:
Mains voltage: max. 250 Vac
Nominal current: 16 A
Requirements class: D (precision protection
in acc. with VDE 0675)
Surge current resistance (8/20 μs wave):
max. 10 kA
Protection level (1.5/50 μs wave): ‹ 1500 V
(L + N against PE)
Master-slave function:
Switching threshold setting range
On: 20 mA - 200 mA
(approx. 55 mA delivery status)
Off: 16 mA - 160 mA
(approx. 44 mA delivery status)
Switching delay: 550 ms +/- 20 %
Electronic module: 2-pole switching
Supply schedule
1 socket strip
2 mounting brackets
Model
Order no.
UP
03.320.109.1
1 unit
03.320.009.1
1 unit
03.321.105.1
1 unit
03.320.105.1
1 unit
03.320.005.1
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® GST18 Plug System (Wieland) Compact
Standard DIN 49 440
DOS20060
DOS00663
DOS20045
With switch
- Quick and efficient plug connection system
- Plug-in electro-installation in place of conventional wiring
- Speed:
- With easy pre-configured element plugging
together
- Flexibility:
- With cable (cable length)
- Rational:
- Easy socket strip swap-out, without costly
cabling
- Safety:
- Faulty installations are ruled out with plug
system
- Space-saving:
- Use of protection and switching functions
can be extended with further cabling without
and plug space loss (max. load rating 16 A)
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
DOS20046
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
- VDE
Color combination
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Load rating
100-240 Vac/16 A
Supply schedule
1 socket strip
2 mounting brackets
Without switch
L
S
n
F1
583
•
•
6
•
•
•
•
433
3
533
7
383
4
F2
19”
Safe
Model
Order no.
UP
With switch
03.302.206.1
1 unit
With switch
03.302.203.1
1 unit
03.300.207.1
1 unit
03.300.204.1
1 unit
Knürr DI-STRIP® Safety Basic
with GST18 plug system
- With overvoltage protection
- Technical description, see page 164
L
DOS20072
S
433
n
F1
F2
19”
Safe
Model
4
Order no.
UP
03.316.204.1
1 unit
Knürr DI-STRIP® Safety Standard
with GST18 plug system
- With overvoltage protection, with integrated mains filter
and lit switch
- Technical description, see page 165
DOS20073
L
S
583
n
F1
F2
19”
Safe
Model
5
Order no.
UP
03.318.205.1
1 unit
Order no.
UP
03.314.205.1
1 unit
Knürr DI-STRIP® Master Slave
with GST18 plug system
- Technical description, see page 166
L
DOS00464
533
S
n
5
F1
F2
19”
Safe
Model
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Euro Socket System, IEC 320
with GST18 plug system
- With 3-way Euro combinations of IEC 320 sockets
- Without fusing
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
DOS20112
Dimensions
Socket spacing: 24 mm 24 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
DOS20107
Load rating
100-240 Vac/10 A
Approval symbols for IEC 320 3-way Euro
combinations
VDE, UR, CSA
Supply schedule
1 socket strip
2 mounting brackets
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CSA NRTL/C
- CB-scheme
Input
L
S
383
DOS20106
Color
Housing: RAL 7035 light gray
Plastic parts: RAL 7021 dark gray
n
F1
6
•
F2
19”
Safe
Model
Order no.
UP
03.600.206.1
1 unit
Output for
further cabling
Knürr DI-STRIP® Safety Basic Euro Socket System IEC 320
with GST18 plug system
- With overvoltage protection
- Technical description, see page 164
L
S
483
n
F1
F2
19”
Safe
Model
6
Order no.
UP
03.616.206.1
1 unit
DOS20110
Knürr DI-STRIP® Safety Standard
with GST18 plug system
- With overvoltage protection with integrated
mains filter
- Technical description, see page 165
L
DOS20109
S
483
n
F1
F2
19”
Safe
Model
Order no.
6
UP
03.618.206.1
1 unit
Order no.
UP
03.612.206.1
1 unit
Knürr DI-STRIP® Power Cleaner
with GST18 plug system
- Technical description, see page 163
L
483
DOS20108
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
S
n
6
F1
F2
19”
Safe
Model
Emerson Network Power Rack PDUs
3-phase in rack with GST18
Strong points
1 DOS20147
2 DOS20132
3 DOS20142
3 DOS20135
1
Requirement
Constantly increasing energy
requirements in the rack caused by
high packing densities (e.g. 1 U
Pizza Servers, Blade Servers, etc.)
2
Solution
3-phase distributor with GST18
plug system, e.g. 96 A and more
with redundant feed
3
Benefits
- Modularity
- Plug-in capability (no wiring
required)
- Expandability
- Cascadability
- Easy provision of redundancies /
UPS secured circuits
- Combination of DIN Schuko and
IEC320, for example
- Installation position freely selectable
- Good alternative for 3-phase
DI-STRIP Triple Power
(see page 156)
Power Supply Cable, 3-Phase
Accessories for GST 18 plug system
- GST 18 socket for connecting GST18i5 distributor
block with 3 phases
- 5-pole (L1, L2, L3, N, PE) 250/400 V ~
- Cable: HO5VV-F 5G 2.5 mm2
L
S
n
F1
F2
19”
Safe
Color
Black
Model
2000
Order no.
UP
04.000.048.0
1 unit
Order no.
UP
04.000.038.9
1 unit
DOS20104
GST18i5 Distributor Block, 3-phase
- For individual connection at the customer
- Modular plug-in connection
- 3 phase distribution on various socket strips
- Including mounting panel
L
DOS20103
S
n
F1
F2
19”
Safe
Color
Black
Model
Emerson Network Power Rack PDUs
Power Supply Cable, 1-Phase
Accessories for GST 18 plug system
- Mains plug CEE/VII - GST18 socket (Wieland)
- Cable - H05VV-F3G 1.5 mm2
L
S
n
F1
F2
19”
Safe
Color
White
Order no.
UP
2000
Model
04.000.040.0
1 unit
5000
04.000.041.0
1 unit
DOS00467
Connection Cable
Accessories for GST 18 plug system
- GST 18 plug
- GST 18 plug
- Cable - H05VV-F3G 1.5 mm2
L
Model
Order no.
200
White
04.000.042.0
1 unit
200
Black
04.000.042.9
1 unit
500
White
04.000.037.0
1 unit
500
Black
04.000.037.9
1 unit
1000
White
04.000.044.0
1 unit
1000
Black
04.000.044.9
1 unit
5000
White
04.000.045.0
1 unit
DOS00469
S
n
F1
F2
Color
For color coding circuits (e.g.UPS)
19”
Safe
UP
DOS20105
GST18 Socket Part
- With screw terminal for cross-section1.5-2.5 mm2
with cable strain relief
- For individual connection at the customer
L
S
n
F1
F2
19”
Safe
Color
White
Model
Order no.
UP
04.000.046.0
1 unit
Order no.
UP
04.000.047.0
1 unit
DOS00471
GST18 Plug Part
- With screw terminal for cross-section1.5-2.5 mm2
with cable strain relief
- For individual, further cabling at the customer
L
DOS00470
S
n
F1
F2
19”
Safe
Color
White
Model
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Euro Socket System, IEC 320
With cable and right angle plug
- Optionally with lit switch, 2-pole switching
- 19” installation option
- With Euro combinations of IEC 320 sockets
Sheet F and Sheet J
- Cable: H05VV-F 3G 1.5 mm2
- Cable: 2.5 m
- Without fusing
DOS20062
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
DOS00498
Dimensions
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color
Housing: RAL 7035 light gray
Plastic parts: RAL 7021 dark gray
Load rating
250 Vac/10 A, Sheet F
250 Vac/16 A, Sheet J
Approval symbols for IEC 320 3-way Euro
combinations
VDE, UR, CSA
Supply schedule
1 socket strip
2 mounting brackets
DOS20042
L
S
n
333
483
F1
•
•
•
•
•
6
•
9
483
12
783
18
783
18
19”
•
•
Input values
Input plug
Outputs
Order no.
Sheet FSheet J
UP
230Vac, 16A
Schuko CEE7
6
03.600.006.1
1 unit
230Vac, 16A
Schuko CEE7
9
03.602.009.1
1 unit
230Vac, 10A
IEC60320 Sheet E
12
03.600.312.1
1 unit
230Vac, 16A
IEC60320 Sheet I
15
3
03.600.418.1
1 unit
230Vac, 16A
IEC60309 1ph/N/PE 6h 15
3
03.600.518.1
1 unit
Knürr DI-STRIP® Euro Socket System, IEC 320
Euro input in plug panel
- With fine-wire fuse 10A
- Optionally with lit switch, 2-pole switching
- 19” installation option
- With 3-way Euro combinations of IEC 320 sockets
DOS00458
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
DOS20041
Dimensions
Socket spacing: 24 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
With switch
Load rating
100-240 Vac
Input: (DC max. 10 A)
Output: (DC max. 10 A)
Supply schedule
1 socket strip
2 mounting brackets
Without switch
L
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Color
Housing: RAL 7035 light gray
Plastic parts: RAL 7021 dark gray
Approval symbols for IEC 320 3-way Euro
combinations
VDE, UR, CSA
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
DOS20040
- Innova-GS
- CSA NRTL/C
- CB-scheme
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
n
F1
383
6
483
9
•
•
6
•
433
S
•
F2
19”
Safe
Model
•
With switch
Order no.
UP
03.622.006.1
1 unit
03.622.009.1
1 unit
03.624.006.1
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Euro Socket System, IEC 320
Euro input on side panel
- With fine-wire fuse 10A
- Optionally with lit switch, 2-pole switching
- 19” installation option
- With 3-way Euro combinations of IEC 320 sockets
Load rating
100-240 Vac
Input: (DC max. 10 A)
Output: (DC max. 10 A)
DOS00460
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Dimensions
Socket spacing: 24 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Approval symbols for IEC 320 3-way Euro
combinations
VDE, UR, CSA
Supply schedule
1 socket strip
2 mounting brackets
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CSA NRTL/C
- CB-scheme
DOS00461
Color
Housing: RAL 7035 light gray
Plastic parts: RAL 7021 dark gray
DOS20043
With switch
L
n
F1
333
S
6
433
9
•
•
383
DOS20044
Without switch
483
•
•
6
9
F2
19”
Safe
•
•
Model
Order no.
UP
03.622.706.1
1 unit
03.622.709.1
1 unit
With switch
03.624.706.1
1 unit
With switch
03.624.709.1
1 unit
Knürr DI-STRIP® Euro Plug System, IEC 320
With cable and right angle plug
- With thermal overload protection, 10 A (can
be reset)
- With lit switch, 1-pole switching
- 19” installation option
- With 2 5-way Euro combinations of IEC 320
sockets
- Cable: H05VV-F 3G 2.5 mm2
- Cable: approx. 5 m
- Molded right angle plug, CEE7/VII, optional
blue 16 A-6h (2P+PE) CEE17 plug
DOS20102
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Dimensions
Socket spacing: 24 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
L
S
n
F1
483
•
10
•
F2
19”
•
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color
Housing: RAL 7035 light gray
Plastic parts: RAL 7021 dark gray
Load rating
250 Vac/10 A
Approval symbols for IEC 320 5-way Euro
combinations
UR, CSA, VDE
Supply schedule
1 socket strip
2 mounting brackets
Safe
Model
Order no.
UP
With switch
03.632.010.1
1 unit
Emerson Network Power Rack PDUs
Mains cable for Euro socket strip
For DIN 49 440 and French/Belgian standard
- Mains plug CEE/VII - Euro socket IEC 320
- Cable
- H05VV-F 3G 1 mm2
Mains voltage
250 VAC
Nominal current
10 A
L
DOS00076
Order no.
UP
2000
S
n
F1
F2
19”
Safe
Model
04.000.054.9
1 unit
6000
04.000.053.9
1 unit
Mains cable for Euro socket strip
For Swiss standard
- Mains plug: Type 12 - Euro socket IEC320
- Cable
- H05VV-F 3G 1 mm2
Mains voltage
250 VAC
Nominal current
10 A
L
DOS00077
S
n
F1
F2
19”
Safe
Model
2000
Order no.
UP
04.000.055.9
1 unit
Mains cable for Euro socket strip
For British standard
- Mains plug: Type BS 1363 - Euro socket IEC 320
- Cable
- H05VV-F 3G 1 mm2
Mains voltage
250 VAC
Nominal current
10 A
L
DOS00078
S
n
F1
F2
19”
Safe
Model
2000
Order no.
UP
04.000.056.9
1 unit
Euro Connection Cable
- Mains plug: IEC 320 - Euro socket IEC320
- Cable
- H05VV-F 3G 1 mm2
- USA: SJT AWG18 with USA approval
L
DOS00519
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
S
n
F1
F2
19”
Safe
Mains voltage
250 VAC
Nominal current
10 A
Model
Order no.
UP
900
EU
04.000.051.9
1 unit
900
USA
04.000.052.9
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Classic
Standard CEE 7-V (UTE) / France
DOS20018
- Optionally with lit switch, 2-pole switching
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
DOS20019
Dimensions
Socket spacing: 24 mm 100 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combination
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .6:
Housing: RAL 2003 pastel orange
Plastic parts: RAL 7035 light gray
Load rating
100-240 Vac/16 A
Supply schedule
1 socket strip
2 mounting brackets
L
n
F1
1783
S
17
1383
13
983
9
583
5
•
•
•
•
•
•
•
•
1733
1333
933
533
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
•
•
•
•
16
12
8
4
F2
19”
Safe
•
•
•
•
•
•
•
•
Model
Order no.
UP
03.400.067.x
1 unit
03.400.063.x
1 unit
03.400.059.x
1 unit
03.400.055.x
1 unit
With switch
03.402.066.x
1 unit
With switch
03.402.062.x
1 unit
With switch
03.402.058.x
1 unit
With switch
03.402.054.x
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Compact
Standard CEE 7-V (UTE) / France
DOS20023
With switch
DOS20022
Without switch
DOS20025
With switch
- Optionally with lit switch, 2-pole switching
- 19” installation option (with length 483 mm)
- 2 versions: Standard side panel or Design side
panel
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Supply schedule
1 socket strip
2 mounting brackets
Without switch
L
n
F1
883
15
•
732
11
683
11
532
7
483
7
382
4
333
4
883
732
683
532
483
382
333
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Color combination
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .6:
Housing: RAL 2003 pastel orange
Plastic parts: RAL 7035 light gray
Load rating
100-240 Vac/16 A
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
DOS20024
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
S
•
•
•
•
•
•
•
14
•
•
•
•
10
10
•
6
6
•
3
3
•
F2
19”
•
•
•
•
•
•
•
•
Safe
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Model
Order no.
UP
03.400.015.x
1 unit
03.400.111.x
1 unit
03.400.011.x
1 unit
03.400.107.x
1 unit
03.400.007.x
1 unit
03.400.104.x
1 unit
03.400.004.x
1 unit
With switch
03.402.014.x
1 unit
With switch
03.402.110.x
1 unit
With switch
03.402.010.x
1 unit
With switch
03.402.106.x
1 unit
With switch
03.402.006.x
1 unit
With switch
03.402.103.x
1 unit
With switch
03.402.003.x
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Protector FI
Standard CEE 7-V (UTE) / France
Protector FI
RCCB for user protection
- Protection with indirect contact as error
protection by switching off with inadmissible
high contact voltage through contact with
electrical equipment
- Protection with direct contact as back-up
protection
- Residual operating current Ig = 10 mA for
alternating and pulsating direct fault current
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
DOS20026
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Dimensions
Socket spacing: 24 mm 50 mm
Height: 78 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combination
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Load rating
100-240 Vac/16 A
Supply schedule
1 socket strip
2 mounting brackets
L
n
F1
883
S
13
683
9
483
5
•
•
•
F2
19”
•
Safe
Model
Order no.
UP
❖
03.404.013.1
1 unit
•
•
03.404.009.1
1 unit
03.404.005.1
1 unit
Knürr DI-STRIP® Protector LS
Standard CEE 7-V (UTE) / France
Protector circuit breaker
- Circuit breaker for overload and short circuit
- Protects cables and feeds with rapid
switching off with short circuit and defined
delayed cutoff with overload
- Circuit breaker: 16 A
- Tripping characteristic, type B, 2-pole
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
DOS20026
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Dimensions
Socket spacing: 24 mm 50 mm
Height: 78 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combination
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Load rating
100-240 Vac/16 A
Supply schedule
1 socket strip
2 mounting brackets
L
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
n
F1
883
S
13
683
9
483
5
•
•
•
F2
19”
Safe
•
•
•
•
Model
Order no.
UP
03.408.013.1
1 unit
03.408.009.1
1 unit
03.408.005.1
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Protector FI / LS
Standard CEE 7-V (UTE) / France
DOS 20026
Protector FI / LS
- Fault current switch and circuit breaker
- Provides a combination of user, overload
and short circuit protection
- Residual operating current Ig = 30 mA for
alternating and pulsating direct fault
current
- Circuit breaker: 16 A
- Tripping characteristic, type B, 2-pole
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
Dimensions
Socket spacing: 24 mm 50 mm
Height: 78 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Color combination
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Load rating
100-240 Vac/16 A
Supply schedule
1 socket strip
2 mounting brackets
L
n
F1
883
S
13
683
9
483
5
•
•
•
F2
19”
Safe
•
•
•
•
Model
Order no.
UP
03.410.013.1
1 unit
03.410.009.1
1 unit
03.410.005.1
1 unit
Knürr DI-STRIP® Protector Emergency STOP
Standard CEE 7-V (UTE) / France
DOS20027
DOS20028
Classic with
emergency stop switch
Compact with
emergency stop switch
- With 2-pole emergency stop switch for user
protection
- For protecting operating personnel
- For manual emergency switching off of the
connected consumers
- Phase and neutral conductors are safely separated
- Switch must be specifically unlocked to restart
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
Material/ Finish
Housing: closed sheet steel extrusion , zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Dimensions
Socket spacing: 24 mm Classic: 100 mm,
Compact: 50 mm
Height: 101 mm
L
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
n
F1
683
S
10
483
6
•
•
1333
12
933
8
•
•
F2
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combinations
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Load rating
100-240 Vac/16 A
Supply schedule
1 socket strip
2 mounting brackets
2 19” mounting bracket (additional with
19” installation option)
19”
Safe
Model
Order no.
UP
03.426.010.1
1 unit
•
•
•
Compact
Compact
03.426.006.1
1 unit
•
•
Classic
03.426.062.1
1 unit
Classic
03.426.058.1
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Protector Emergency Stop FI / LS
Standard CEE 7-V (UTE) / France
DOS20029
With emergency Off switch
and FI/LS circuit breaker
- With 2-pole emergency stop switch for user
protection
- For protecting operating personnel
- For manual emergency switching off of the
connected consumers
- Phase and neutral conductors are safely separated
- Switch must be specifically unlocked to restart
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Dimensions
Socket spacing: 24 mm Compact: 50 mm
Height: 101 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
L
S
683
n
F1
8
•
F2
19”
Safe
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combinations
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Additionally:
With 2-pole fault current switch and circuit
breaker
Provides a combination of user, overload
and short circuit protection
Load rating
100-240Vac/16 A
Supply schedule
1 socket strip
2 mounting brackets
Model
•
Order no.
UP
03.428.008.1
1 unit
Knürr DI-STRIP® Power Cleaner
Standard CEE 7-V (UTE) / France
DOS20030
With mains filter
- High-frequency glitches are generally caused
by switching processes in an operation from
100 kHz to 5MHz. This high-frequency rate
overloads the mains frequency and affects
adjacent electronic equipment. The mains
filter attenuates this high-frequency rate.
- The attenuation behavior is harmonized with
the typical interference spectrum.
- The mains filter works in both directions. This
means that glitches from the equipment to the
socket strip are also filtered from the mains.
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combination
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .6:
Housing: RAL 2003 pastel orange
Plastic parts: RAL 7035 light gray
Load rating
Nominal voltage: max. 250 Vac, 50 Hz
Nominal current: max. 16 A
Supply schedule
1 socket strip
2 mounting brackets
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
L
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
n
F1
883
S
13
683
9
483
5
•
•
•
F2
19”
Safe
•
•
•
•
Model
Order no.
UP
03.412.013.x
1 unit
03.412.009.x
1 unit
03.412.005.x
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Safety Basic
Standard CEE 7-V (UTE) / France
DOS20031
DOS20032
- For protecting against transient overvoltages
from the mains, which, for example, are
caused by switching machines on and off.
- With critical overvoltages the mains is separated.
- Once the safety arrester has been triggered the
green function display goes out. The socket
strip can then no longer be used. Send the
socket strip to the manufacturer for the safety
arrester to be replaced!
- The safety effect of the type 3 test category
and requirements category “D” is to protect
the equipment, i.e. precision protection.
- The protection devices of the test and requirements categories 1 and 2 and B and C must be
preconnected in the building installation to
ensure optimum protection.
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color
Final digit of order number .1:
RAL 7035 light gray
Technical data
Test category: Type 3
- In acc. with DIN EN 61643-11
Requirements class: D
- In acc. with VDE 0675-6
Mains voltage: 230 VAC
Nominal current: max. 16 A
Cut-off discharge current (8/20 μs): 10 kA
Response time: ‹ 25 ns
Protection level
(with 100 A varistor peak current):
- L with respect to N: ‹ 800 V
- L/N with respect to PE: ‹ 1500 V
Supply schedule
1 socket strip
2 mounting brackets
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
L
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
S
n
732
10
683
10
532
6
483
6
432
4
383
4
F1
•
•
•
F2
19”
•
•
•
•
Safe
•
•
•
•
•
•
Model
Order no.
UP
03.416.110.1
1 unit
03.416.010.1
1 unit
03.416.106.1
1 unit
03.416.006.1
1 unit
03.416.104.1
1 unit
03.416.004.1
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Safety Standard
Standard CEE 7-V (UTE) / France
DOS20033
DOS20034
With overvoltage protection
and mains filter
With overvoltage protection
and mains filter
- The “Safety Standard” models consist of a
combined overvoltage protection/mains filter
element.
- For protecting against transient overvoltages
from the mains, which, for example, are
caused by switching machines on and off.
- With critical overvoltages the mains is separated.
- Once the safety arrester has been triggered the
green function display goes out. The socket
strip can then no longer be used. Send the
socket strip to the manufacturer for the safety
arrester to be replaced!
- The safety effect of the type 3 test category
and requirements category “D” is to protect
the equipment, i.e. precision protection.
- The protection devices of the test and requirements categories 1 and 2 and B and C must be
preconnected in the building installation to
ensure optimum protection.
- High-frequency glitches are generally caused
by switching processes in an operation from
100 kHz to 5MHz.
- This high-frequency rate overloads the mains
frequency and affects adjacent electronic
equipment. The mains filter attenuates this
high-frequency rate.
- The attenuation behavior is harmonized with
the typical interference spectrum.
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
L
S
n
F1
883
•
•
•
•
•
13
•
732
683
532
483
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
9
9
•
5
5
•
F2
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combination
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .6:
Housing: RAL 2003 pastel orange
Plastic parts: RAL 7035 light gray
Technical data
Mains voltage: 230 VAC
Nominal current: max. 16 A
Cut-off discharge current (8/20 μs): 10 kA
Response time: ‹ 25 ns
Protection level
(with 100 A varistor peak current):
- L with respect to N: ‹ 800 V
- L/N with respect to PE: ‹ 1500 V
Overvoltage protection
Requirements class: D
- In acc. with VDE 0675-6
Mains filter
- In acc. with VDE 0565 (EN 60939)
Supply schedule
1 socket strip
2 mounting brackets
19”
Safe
Model
Order no.
UP
With switch
03.418.013.x
1 unit
With switch
03.418.109.x
1 unit
With switch
03.418.009.x
1 unit
With switch
03.418.105.x
1 unit
•
•
•
•
•
•
With switch
03.418.005.x
1 unit
•
•
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Master Slave
Standard CEE 7-V (UTE) / France
DOS20035
With master-slave module
- If the master equipment is switched, the slave
sockets are also switched (together, with a
short delay to the master). This means convenient switching on and off of several hard to
access devices. Switching thresholds can be set
from outside via potentiometer.
- Note:
- The master equipment power consumption
must be continuously above the switching-on
threshold. When switching off the master
equipment, the power consumption must fall
below the switching-off threshold.
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
n
F1
683
S
9
483
5
•
•
F2
Color combination
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Load rating
Max. 250 Vac/16 A
Technical data
Switching threshold setting range
On: 20 mA - 200 mA
(approx. 55 mA delivery status)
Off: 16 mA - 160 mA
(approx. 44 mA delivery status)
Switching delay: 550 ms +/- 20 %
Electronic module: 2-pole switching
Supply schedule
1 socket strip
2 mounting brackets
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
L
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
19”
Safe
•
•
•
Model
Order no.
UP
03.414.009.1
1 unit
03.414.005.1
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Combi
Standard CEE 7-V (UTE) / France
DOS20037
DOS20036
Master-slave,
overvoltage protection
and mains filter
- Master-slave with overvoltage protection and
mains filter
- Automatic consumer switching
- Combines Master-Slave (page 7.32) and Safety
Standard (page 7.31) functions
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Master-slave,
overvoltage protection
and mains filter
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
L
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
S
n
782
9
733
9
582
5
533
5
F1
•
•
F2
•
•
19”
Safe
•
•
•
•
Color combination
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Technical data
Overvoltage protection and mains filter:
Mains voltage: max. 250 Vac
Nominal current: 16 A
Requirements class: D (precision protection
in acc. with VDE 0675)
Surge current resistance (8/20 μs wave):
max. 10 kA
Protection level (1.5/50 μs wave): ‹ 1500 V
(L + N against PE)
Master-slave function:
Switching threshold setting range
On: 20 mA - 200 mA
(approx. 55 mA delivery status)
Off: 16 mA - 160 mA
(approx. 44 mA delivery status)
Switching delay: 550 ms +/- 20 %
Electronic module: 2-pole switching
Supply schedule
1 socket strip
2 mounting brackets
Model
Order no.
UP
03.420.109.1
1 unit
03.420.009.1
1 unit
03.420.105.1
1 unit
03.420.005.1
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Compact GST 18 Plug System (Wieland)
Standard CEE 7-V (UTE) / France
DOS20048
DOS20047
GST 18 with switch
GST 18 without switch
- Quick and efficient plug connection system
- Plug-in electro-installation in place of conventional wiring
- Speed:
- With easy pre-configured element plugging
together
- Flexibility:
- With cable (cable length)
- Rational:
- Easy socket strip swap-out, without costly
cabling
- Safety:
- Faulty installations are ruled out with plug
system
- Space-saving:
- Use of protection and switching functions
can be extended with further cabling without
and plug space loss (max. load rating 16 A)
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
L
S
n
F1
583
•
•
6
•
•
•
•
433
3
533
7
383
4
F2
19”
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combination
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Load rating
100-240 Vac/16 A
Supply schedule
1 socket strip
2 mounting brackets
Safe
Model
Order no.
UP
•
•
•
•
With switch
03.402.206.1
1 unit
With switch
03.402.203.1
1 unit
03.400.207.1
1 unit
03.400.204.1
1 unit
Knürr DI-STRIP® Safety Basic
with GST18 plug system / France
DOS20051
- With overvoltage protection
- Technical description, see page 180
L
S
433
n
F1
F2
19”
Safe
Model
•
4
Order no.
UP
03.416.204.1
1 unit
Knürr DI-STRIP® Safety Standard
with GST18 plug system
DOS20052
- With overvoltage protection, with integrated
mains filter and lit switch
- Technical description, see page 181
L
S
583
n
F1
F2
19”
Safe
Model
•
5
Order no.
UP
03.418.205.1
1 unit
Order no.
UP
03.414.205.1
1 unit
Knürr DI-STRIP® Master Slave
with GST18 plug system
DOS20054
- Technical description, see page 182
L
533
S
n
5
F1
F2
19”
Safe
•
Model
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Classic
Standard CH SEV 1011
- With/without switch, socket spacing, 100 mm
- Optionally with lit switch, 2-pole switching
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded plug
DOS00717
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
DOS00664
Classic with switch
Dimensions
Socket spacing: 24 mm 100 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
DOS00665
Classic without switch
L
n
F1
1783
S
17
1383
13
983
9
583
5
•
•
•
•
•
•
•
•
1733
1333
933
533
•
•
•
•
16
12
8
4
F2
19”
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combination
Final digit of order number .1:
RAL 7035 light gray
Final digit of order number .6:
Housing: RAL 2003 pastel orange
Plastic parts: RAL 7035 light gray
Load rating
100-240 Vac/10 A
Supply schedule
1 socket strip
2 mounting brackets
Safe
Model
Order no.
UP
03.700.067.x
1 unit
03.700.063.x
1 unit
03.700.059.x
1 unit
03.700.055.x
1 unit
With switch
03.702.066.x
1 unit
With switch
03.702.062.x
1 unit
With switch
03.702.058.x
1 unit
With switch
03.702.054.x
1 unit
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Compact
Standard CH SEV 1011
- Optionally with lit switch, 2-pole switching
- 19” installation option (with length 483 mm)
- 2 models, standard side or design side
- Socket rotation: 45º
- Cable: H05VV-F 3G 1.5 mm2
- Molded plug
DOS20074
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
DOS00666
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combination
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Load rating
100-240 Vac/10 A
Supply schedule
1 socket strip
2 mounting brackets
DOS20038
L
DOS20039
DOS00667
n
F1
883
15
•
732
11
683
11
532
7
483
7
382
4
333
4
732
683
532
483
382
333
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
S
•
•
•
•
•
•
•
•
•
10
10
•
6
6
•
3
3
•
F2
19”
Safe
Model
Order no.
UP
03.700.015.1
1 unit
03.700.111.1
1 unit
03.700.011.1
1 unit
03.700.107.1
1 unit
03.700.007.1
1 unit
03.700.104.1
1 unit
03.700.004.1
1 unit
With switch
03.702.110.1
1 unit
With switch
03.702.010.1
1 unit
With switch
03.702.106.1
1 unit
With switch
03.702.006.1
1 unit
With switch
03.702.103.1
1 unit
With switch
03.702.003.1
1 unit
•
•
•
•
•
•
•
•
Emerson Network Power Rack PDUs
Knürr DI-STRIP® Protector FI/LS
Standard CH SEV 1011
Protector FI/ LS
- Fault current switch and circuit breaker
- Provides a combination of user, overload
and short circuit protection
- Residual operating current Ig = 30 mA for
alternating and pulsating direct fault
current
- Circuit breaker: 10 A
- Tripping characteristic, type B, 2-pole
DOS00719
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded right angle plug
DOS00668
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
Dimensions
Socket spacing: 24 mm 50 mm
Height: 78 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 m
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combination
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Load rating
100-240 Vac/10 A
Supply schedule
1 socket strip
2 mounting brackets
L
n
F1
683
S
9
483
5
•
•
F2
19”
Safe
Model
•
Order no.
UP
03.710.009.1
1 unit
03.710.005.1
1 unit
Knürr DI-STRIP® Safety Standard
Standard CH SEV 1011
- With overvoltage protection and integrated
mains filter
- With lit switch, 2-pole switching
- 19” installation option (with length 483 mm)
- Socket rotation: 45°
- Cable: H05VV-F 3G 1.5 mm2
- Molded plug
DOS00720
DOS00669
Material/ Finish
Housing: closed sheet steel extrusion, zincpassivated, powder-coated texture
Plastic parts: Vampamid 6 0024 VO (UL94),
recyclable
Internal conductor: full-length busbar, brass
With overvoltage
protection and mains filter
Dimensions
Socket spacing: 24 mm 50 mm
Height: 45.5 mm
Housing width: 44.4 mm (= 1 U)
Cable 2.5 mm
L
S
n
F1
683
•
•
9
•
•
483
Dimensions in mm: L =
S =
n =
F1 =
F2 =
19”=
Safe=
Length
U = standard height unit
Switch
UP = Unit of packaging
Number of sockets
Standard side
= Express item
Design side
Suitable for 19” installation
Child-safe,
Conversion:
1 mm = 0.03937 inch
1 kg = 2.2046 pound
Replace .x with the number of your color combination:
.1 = RAL 7035, .6 = RAL 7035/RAL 2003
5
F2
19”
•
Approvals/certificates
- CE label in accordance with low voltage
guideline 2006/95/EWG
- EMC Directive 2004/108/EC
- Innova-GS
- CB-scheme
Color combination
Final digit of order number .1:
RAL 7035 light gray
Plastic parts: RAL 7035 light gray
Description and technical data
(See page 165)
Nominal current: 10 A
Supply schedule
1 socket strip
2 mounting brackets
2 19” mounting brackets (additional with
19” installation option)
Safe
Model
Order no.
UP
With switch
03.718.009.1
1 unit
With switch
03.718.005.1
1 unit
Knürr PowerTrans ®
Knürr
PowerTrans
Power Distribution Rack
Central connection unit for
power supplies for individual
server racks.
®
Knürr PowerTrans ®
Power Distribution Rack
PowerTrans ®®
The Knürr PowerTrans® Rack is the interface between the low
voltage feed and the Power Distribution Unit (PDU) of the
Knürr DI-STRIP® family, as well as other Emerson Network
Power PDUs for supplying servers and further IT devices.
The power distribution is performed in the individual plug-in units
and therefore no longer has to be installed fixed in the building. Up
to 8 plug-in units can be integrated. Each plug-in unit is supplied
with an A and B feed (redundancy). With max. 250 A/phase loads
of up to 329 kVA can be supplied from just one single rack.
Knürr PowerTrans®
Strong points
1
2
Equipping and installation
The outputs on the plug-in units can
be flexibly configured according to
customer requirements via various
plug connections, type CEE and GST 18.
(e.g. BladePower® or PizzaPower®,
DI-STRIP® TriplePower®, and flexible distribution with the GST18i5
distributor block, 3-phase).
Two 3-phase feeds
- Feed A and feed B both threephase with max. 250A/phase L1,
L2, L3, N, PE
- Ideal for providing feed redundancies
3
Cable routing
Convenient cable routing from
above and below.
4
Costs-conscious
Only the main feed on the rack
must be installed by an electrician.
The individual plug-in units and the
PDUs can be connected per Plug &
Play installation, thereby allowing
later extensions to be performed
cost-effectively.
1 MIR20388
2 MIR20390
3 MIR20391
4 MIR20386
Knürr PowerTrans ®
Knürr PowerTrans®
19” Power Distribution Rack
– Feed of 2 separate 3-phase 400V mains, L1,
L2, L3, N, PE
– Each with a 250A circuit breaker in the input
– Distribution to the individual plugs via busbars
and contact-safe plug-in connections
– Up to 8 slot-in units with A feed and B feed
are possible
■ Material / Finish
- Basic rack, extruded aluminum, polished
- Corner piece, die-cast aluminum, polished
- Glass infill front door, single safety glass
panel, 4mm
- Covers, zinc-passivated sheet steel, powdercoated texture
■ Color
RAL 7021 dark gray
■ Supply schedule
1 rack with covers and front door
1 plinth for cable entry on the side and rear
with leveling feet (0-25mm)
2 plinth trims for front and rear, with vent
slots and fixing for filter mat
2 plinth trims, closed
1 set of busbars, safe from contact for A feed
and B feed
2 circuit breakers with max. 250 A
16 power supply plugs for the slot-in units
wired on the busbars
5 multifunctional braces with jumper bracket
2 19” T-slot extrusions
16 chassis rails
1 complete earthing set
1 complete locking set
■ How supplied
Assembled
MIR20377
W
H
800
2120 1000
D
U
h d
kg
Model
Order no.
UP
03.014.501.8
1 unit
Knürr PowerTrans® 19” Chassis
MIR20383
–
–
–
–
–
–
19” slot-in housing
Width 19”
Height 3 U
Depth 480 mm
Color: RAL 7021 dark gray
2 separate 3-phase inputs with max. 63A
phase current
– Outputs acc. to variants 1-4
■ Variant 3 Plug-in
- 6 protected 1-phase outputs 230V/400V
16A via GST18i5 Euro installed socket, 3Ph
- Suitable for connecting GST18i5 distributor
block, 3-phase (04.000.038.9, for flexible
distribution to 1-phase socket strips) as well
as connecting a TriplePower 3-phase
(03.600.024.1 or 03.600.048.1)
■ Variant 1 Plug-in
- 2 protected 3-phase outputs, 230V/400V
32A via IEC60309 socket, 3Ph/N/PE 6h, red
- Suitable for connecting 2 PizzaPower 3-phase
(03.631.021.1) or 2 BladePower 3-phase
(03.630.015.1)
■ Variant 4 Plug-in
- Empty housing
- For customer-specific equipping
■ How supplied
Assembled
■ Variant 2 Plug-in
- 4 protected 1-phase outputs, 230V 32A via
IEC60309 socket, 1Ph/N/PE 6h, blue
- Suitable for connecting 4 PizzaPower 1-phase
(03.631.007.1) or 4 BladePower 1-phase
(03.630.005.1)
W
MIR20382
19”
H
D
U
Model
Order no.
UP
479
3
Variant 1
03.014.003.8
1 unit
19”
479
3
Variant 2
03.014.002.8
1 unit
19”
479
3
Variant 3
03.014.001.8
1 unit
19”
479
3
Variant 4
03.014.000.8
1 unit
Knürr PowerTrans ®
... multifunctional use
Connection example for 3-phase (32 A)
power distribution in data centers with
blade servers and pizza servers.
Socket strip connection cable length
can be freely selected (max. 20 m).
3-phase variant: BladePower ® and PizzaPower ®
Connection example for 1-phase (32 A)
power distribution in data centers with
blade servers and pizza servers.
Socket strip connection cable length
can be freely selected (max. 20 m).
1-phase variant: BladePower® and PizzaPower®
Connection example for 1-phase and
3-phase (16 A) power distribution in
network racks.
Socket strip connection cable length
can be freely selected (max. 20 m).
1-phase and 3-phase variant: DISTRIP® and TriplePower®
UPS
Emerson Network Power UPS
UPS
Uninterruptible
Power Supply
Emerson Network Power UPS
Tower Solutions • 19” Slot-In • Large Scale Systems
UPS
The right technical solution for every requirement.
UPS20082
Uninterruptible Power Supplies
Strong points
Safety:
High-grade online and line interactive technology guarantees safe
and uniterruptible operation of
your systems.
Efficiency:
The 19” modules provide high performance on minimum installation
space with compact construction
and modular setup.
Investment security:
Our solutions grow with your
requirements, can be flexibly used
and are easily expanded.
Central UPS systems
Higher power classes, 10 kVA to
4800 kVA, with installation and
maintenance on request.
Modularity:
The individual components of this
range can be combined according
to requirements and consequently
produce specifically defined solutions.
User-friendliness
Comprehensive displays and interactive interfaces for external
analysis of status messages provide the user with current system
information at all times.
Highest possible protection
Online UPS systems provide the
highest possible protection against
the 10 most frequent mains disturbances.
Emerson Network Power UPS
Line-InterActive / PowerSure PSI XR
IEC 62040-3 VI-SS-313
The line interactive UPS model uses an
inverter in inverse operation to recharge
the battery with stable mains supply.
If the mains power supply fails, then
the working direction changes and the
battery powers the inverter.
Because the transducer constantly
monitors the mains input, it can react
quicker to failures and correct voltage
breaks.
The transducer connected upstream
from the consumer has a specific filtering effect against mains disturbances.
This technology is highly recommendable for uninterruptible power supplies
for many applications, particularly with
regard to PC requirements.
UPS20085
Power Quality Systems
Liebert PSI XR
Protection in rack and tower use for
networks, telecommunications and
servers
Hot-swappable
batteries
Professional desktop
PCs
Line-InterActive
Design
Switches, hubs, routers
& bridges
Universal communication
options
Extendable bridging
times
Data center facilities
Telecommunication
switchgear units
Emerson Network Power UPS
Liebert® PSI-XR
High-performance rack & tower UPS system for network protection
The Liebert PSI-XR is a compact UPS
system with line-interactive technology,
which was specially designed for IT
applications, such as network racks and
small data centers, for example.
The Liebert PSI-XR’s flexible design
allows the unit to be configured as a
standalone tower and rack installation
over 2 U.
The Liebert PSI-XR is available as both
230-V and 120-V model in four different
power classes.
The UPS is especially impressive with
its innovative line-interactive design
and automatic voltage regulation. This
protects against voltage fluctuations
by increasing or reducing the power
supply to the level required by the
connected devices. The UPS system
also ensures longer battery service life,
as the devices are supplied for as long
as possible via the mains.
Liebert PSI-XR standard equipment
Flexibility:
- Six or seven battery backed-up
outputs
- Configurable input voltage range
- Free swivel display panel
- Automatic frequency scanning
- Several communication options
(serial, USB, SNMP and contact
closure)
Higher availability
- Data cable overvoltage protection
- UPS system status early warning
system
- Fully automatic battery test
- Lightning and overvoltage protection
- Remote emergency stop
- Hot-swappable batteries the user
can change
- Sufficient battery run time under
full charge with power failures for
proper shut down of the connected
equipment
Lowest possible TCO (Total Cost
of Ownership)
- 0.9 power factor for more power
for the protected devices and
energy-efficient operation
- Wide input voltage range
- Reduced installation input (costs
and time)
- Standard two year warranty
Ideal for:
- PCs
- Networked workstations
- Servers
- Network racks
- Big network peripheries
- VolP
PSI XR 2U Rack version
PSI XR 2U Tower version
Emerson Network Power UPS
Liebert® PSI XR specifications
Model
PS1000RT3-230XR
Power data
VA
1000VA
W
900W
Dimensions and weight
Device (WxDxH mm)
440 x 490.5 x 88
Shipping size (WxDxH mm)
560 x 612 x 228
Weight - device (kg)
25
Shipping weight (kg)
29
Input parameters
Frequency
Voltage range without battery operation
Frequency range
Input connection
IEC320-C14
Output parameters
Output connections
(6) IEC320-C13
Voltage (Normal Mode)
Voltage (Battery Mode)
Transfer Time
On-Battery Waveform
Overload Warning
Battery Parameters
Type
Quantity x Voltage x Rating
Recharge Time
Battery Backup Time
Environmental
Operating/ Storage Temperature, °C
Relative Humidity
Operating Altitude
Audible Noise
Agency
Safety
EMC
Transportation
Warranty
Packaging
Order no.
Order no. SNMP Card
PS1500RT3-230XR
PS2200RT3-230XR
PS3000RT3-230XR
1500VA
1350W
2200VA
1980W
3000VA
2700W
440 x 490.5 x 88
560 x 612 x 228
28
32
440 x 700.5 x 88
560 x 821 x 228
42
47
440 x 700.5 x 88
560 x 821 x 228
46
51
220
165 to 300 VAC (configurable)
45 - 65 Hz, (± 0.5 Hz)
IEC320-C14
IEC320-C20
IEC320-C20
(6) IEC320-C13
(6) IEC320-C13
(6) IEC320-C13
(1) IEC320-C19
(1) IEC320-C19
220/230/240 VAC (configurable)
220/230/240 VAC (configurable); ± 5% before low-battery warning
4-6 ms typical
Sine wave
›100%
Valve-regulated, nonspillable, lead acid
4 x 12 x 7.2
4 x 12 x 9
8 x 12 x 7.2
8 x 12 x 9
5 hours to 90% of rated capacity, after full discharge into resistive load
0 to 40 / -15 to 40
0% to 90%, non-condensing
Up to 3000m at 35° without derating
‹ 40 dBA, internal fan(s) Off; ‹ 45 dBA, internal fan(s) On
IEC 62040-1-1
IEC/EN/AS 62040-2 2nd Ed Class A
ISTA Procedure 1A Certification
2 years standard (+ 1 year warranty extension available)
User Manual on CD, Software CD, DB9 Serial cable, USB Cable, Tower Stands, Rack-Handles
w/mounting hardware, Safety Instruction Sheet, Environment protection sheet, REPO mate socket,
(2) IEC output cables for 1000/1500 VA and (3) IEC output cables for 2200/3000 VA, for PS 2200/3000;
(1) “Shucko” CEE 7/7 to IEC-320-C19 input cord and (1) UK plug to IEC-320-C19 input cord
06.099.027.1
06.099.028.1
06.099.029.1
06.099.030.1
06.099.022.1
Liebert® PSI XR Battery Cabinet Specifications
Model
Used w/UPS Model
Dimensions, W x D x H, mm
Unit / Shipping
Weight, kg
Unit / Shipping
Batteries
Type
Quantity x Voltage x Rating
Battery Manufacturer
Environmental
Operating / Storage Temperature, °C
Relative Humidity
Maximum Operating Altitude
Agency
Safety / Emissions
Transportation
Order no.
PSRT3-24VBXR
PS1000RT3-230XR / PS1500RT3-230XR
PSRT3-48VBXR
PS2200RT3-230XR / PS3000RT3-230XR
440 x 490.5 x 88 / 560 x 675 x 228
8 x 12 x 7.2
CSB, YUASA or Equivalent
Emerson Network Power™
Leading global provider of
Business-Critical Continuity™ solutions.
0 to 40 / -15 to 40
0% to 90%, non-condensing
3000m at 35° without derating
IEC/EN/AS 62040-1-1 / IEC/EN/AS 62040-2 2nd Ed Class A
ISTA Procedure 1A Certification
06.099.034.1
06.099.035.1
PS1000RT3-230XR
15 / 6
73 /31
129 / 65
181 / 96
233 / 124
285 / 151
336 / 179
All names appearing in the text are
trademarks or registered trademarks
of the respective company.
103735
Valve-regulated, nonspillable, lead acid
Battery runtime chart (runtimes in minutes; with fully charged batteries; ambient temperature 25 °C)
Number of batteries
Internal Battery (half/full load)
1 Cabinet (half/full load)
2 Cabinet (half/full load)
3 Cabinet (half/full load)
4 Cabinet (half/full load)
5 Cabinet (half/full load)
6 Cabinet (half/full load)
© 2009 Liebert Corporation. All rights
reserved worldwide. Specifications
may change without prior notice.
® Liebert is a registered trademark of
the Liebert Corporation.
29 / 33
8 x 12 x 7.2
Although much time and effort went
into ensuring that this brochure is
accurate and complete, the Liebert
Corporation does not accept responsibility for its content and does not
accept any form of liability for damages that may result from the use of
this information, nor does it accept
responsibility for errors or omissions.
PS1500RT3-230XR
13 / 5
55 / 18
95 / 46
131 / 64
167 / 82
203 / 106
239 / 124
PS2200RT3-230XR
14 / 5
45 / 15
67 / 29
95 / 48
143 / 72
167 / 84
191 / 102
PS3000RT3-230XR
13 / 5
31 / 12
56 / 18
73 / 31
95 / 47
113 / 56
131 / 65
■
■
■
■
■
■
■
■
■
■
■
■
Alternating Current
Connectivity
Direct Current
Integrated Computing
Embedded Power
Monitoring
Outside Plant
Power Switching and Regulation
Precision Cooling
Racks and Integrated Enclosure
Services
Overvoltage Protection
Emerson Network Power.com
Business-Critical Continuity, Emerson
Network Power and the Emerson
Network Power logo are trademarks
and service marks of Emerson Electric
Co. © 2009 Emerson Electric Co.
Emerson Network Power UPS
Liebert® PSI
High performance rack & tower UPS system for network protection
The Liebert PSI is a compact UPS system
with line-interactive technology, which
was specially designed for IT applications,
such as network racks and small data
centers, for example.
The Liebert PSI’s flexible design allows
the unit to be configured as a standalone tower and rack installation over
2 U.
The Liebert PSI-XR is available as both
230-V and 120-V model in four different
power classes.
The UPS is especially impressive with
its innovative line-interactive design
and automatic voltage regulation. This
protects against voltage fluctuations
by increasing or reducing the power
supply to the level required by the
connected devices. The UPS system
also ensures longer battery service life,
as the devices are supplied for as long
as possible via the mains.
Flexibility:
- Battery backed-up outputs
- Configurable input voltage range
- Free swivel display panel
- Automatic frequency scanning
- Rack runner rails
- Several communication options
- Contact closure, USB and SNMP
Higher availability
- Data cable overvoltage protection
- UPS system status early warning
system
- Up to five minutes battery runtime
with power failures (fully charged)
- Fully automatic battery test
- Overvoltage protection
- Remote emergency stop
- Hot-swappable batteries
Lowest possible TCO (Total Cost
of Ownership)
- Power factor 0.9
- Wide input voltage range
- Reduced installation input (costs
and time)
- Warranty
Ideal for:
- PCs
- Networked workstations
- Servers
- Network racks
- Big network peripheries
- VolP
PSI 2U Rack version
PSI 2U Tower version
Emerson Network Power UPS
Liebert® PSI specifications
Model
PS750RT3-230
PS1000RT3-230
PS1500RT3-230
PS2200RT3-230
PS3000RT3-230
Power Rating
750VA/675W
1000VA/900W
1500VA/1350W
2200VA/1980W
3000VA/2700W
Dimensions, W x D x H - mm
Unit
440 x 412 x 88
446 x 657 x 88
Shipping
560 x 595 x 228
560 x 776 x 228
Weight - kg
Unit
15
19.4
20.9
33.8
37.2
Shipping
18.2
22.6
24.1
38.3
41.5
Input AC Parameters
Surge Protection
220J
Voltage Range Without Battery Operation
165-300, Configurable
Frequency Range
45-65Hz, (+ 0.5Hz)
Input Socket
IEC-320-C14
IEC-320-C20
Output Receptacles
(8) IEC-320-C13
(8) IEC-320-C13 - (1) IEC-320-C19
Voltage, Normal Mode
220/230/240 VAC, Configurable, +10%
Voltage, Battery Mode
220/230/240 VAC, Configurable; +5% Before Low Battery Warning
Transfer Time
4-6 ms, Typical
Waveform
Sine wave
Overload Warning
› 100%
Battery Parameters
Type
Valve-Regulated, Nonspillable, Lead Acid
Quantity x Voltage x Ah
2 x 12 x 7.2
3 x 12 x 7.2
3 x 12 x 9
6 x 12 x 7.2
6 x 12 x 9
Backup Time
See Load Autonomy table below
Recharge Time
5 hours to 90% of rated capacity, after full discharge into resistive load
Environmental
Operating Temperature
0°C to 40°C (32°F to 104°F)
Storage Temperature
-15° to 40°C (5°F to 104°F)
Relative Humidity
0% to 90%, non-condensing
Operating Altitude
Up to 3000m (10,000 ft.) at 35°C (95°F) without derating
Audible Noise
‹ 45 dBA
Agency
Safety
IEC/FN/AS 62040-1-1
Surge
IEC/FN/AS 61000-4-2
ESD
IEC/FN/AS 61000-4-3
Susceptibility
IEC/FN/AS 61000-4-4
Electrical Fast Transient
IEC/EN/AS 62040-2 2nd Ed class A
Emissions
IEC/FN/AS 61000-4-6
Conducted Immunity
IEC/EN/AS 61000-3-2
Harmonics
IEC/FN/AS 61000-4-6
Transportation
ISTA Procedure 1A Certification
Environmental
ROHS compliant
Warranty
2 years standard (+1 year warranty extension available)
Packaging
Multi-Language User Manual on CD, Liebert Multi inkk. Software on CD, Contact
Closure (MI 9P9S) Cable USB Cable, Tower Stand, Mounting Hardware, Rack-Mount-Handles,
Fixed Mounting Rails, FPO Connector, Input Power Cord. 2200/3000 only: 2- (1)
Schuko to IEC-320-C19 and (1) UKplug to IEC-320-C19 input cord.
IEC Output Cable, 750/1000/1500 only: 2 - (2) IEC-320-C13, IEC Output Cable, 2200/3000 only: 3 - (3) IEC-320-C13
Order no.
06.099.061.1
06.099.062.1
06.099.063.1
06.099.064.1
06.099.065.1
Order no. SNMP Card
06.099.022.1
Technical support
Always at your disposal: Our commitment to your business, provided by
our technical support in five languages (English, Spanish, French,
Italian, German).
Free: 00-80011554499
Subject to a charge: +39 02 98250222
[email protected]
Although much time and effort went
into ensuring that this brochure is
accurate and complete, the Liebert
Corporation does not accept responsibility for its content and does not accept
any form of liability for damages that
may result from the use of this information, nor does it accept responsibility
for errors or omissions.
© 2010 Liebert Corporation.
All rights reserved worldwide. Specifications may change without prior
notice.
PSI00-FLY-EN-1209-01
Emerson Network Power™
Leading global provider of
Business-Critical Continuity™ solutions.
Load Autonomy - Liebert PSI 750VA-3000VA
Load %
750VA
1000VA
1500VA
2200VA
10
84
93
76
82
20
45
47
32
44
30
25
26
17
19
40
15
15
12
14
Internal Battery
50
11
12
9
11
60
9
9
7
9
70
7
7
5
7
80
5
6
4
5
90
4
5
3
4
100
4
4
3
3
Note: All run times are in minutes, assume fully charged batteries and are typical at 25°C (77°F) with resistive loads.
3000VA
76
32
17
12
9
7
5
4
3
3
■
■
■
■
■
■
■
■
■
■
■
■
AC Power
Connectivity
DC Power
Integrated Computing
Embedded Power
Infrastructure Management &
Monitoring
Outside Plant
Power Switching and Regulation
Precision Cooling
Racks and Integrated Enclosure
Services
Overvoltage Protection
Emerson Network Power.com
Emerson, Business-Critical Continuity™
and Emerson Network Power
trademarks of Emerson Electric
Co. or affiliated companies.
© 2010 Emerson Electric Co.
Emerson Network Power UPS
Online / GXT2 and GXT3
IEC 62040-3 VFI-SS-111
On-line UPS systems have the advantage of effectively filtering out spikes
and drop outs by converting alternating voltage into direct voltage and
back into alternating voltage.
Our online UPS systems are series
equipped with interfaces, so that
unattended computers can be specifically powered down automatically
and powered up again after the mains
supply has returned.
USV20086
The accumulator takes over from the
rectifier without any interruption when
there is a mains failure and provides the
necessary energy for a certain length of
time. On-line systems provide high levels
of security and are particularly recommended for high-grade and sensitive
consumers.
If faults occur in the system itself due to
battery aging processes, an automatic
by-pass switch ensures bridging and
direct connection to the mains without
interruption.
The user is acoustically and optically
informed about defective functions
and power failures.
Systems for quality power
GXT2 and GXT3
True Online Power
Full energy for your company
Hot-swap
batteries
Professional PC
workstations
Online
technology
Small hubs, routers &
bridges
Diverse communication
options
Data center
Extendable back-up
times
Telecom equipment
Emerson Network Power UPS
Liebert® GXT3, 700VA - 3000VA Model
Reliable online UPS protection in compact 2 U package
The Liebert GXT3 is a true online UPS,
which continuously supplies the IT
equipment with quality alternating
current. No interruption with
changeover to batteries. They protect
devices from almost all power supply
faults – be they caused by power failures, voltage spikes, voltage drops or
whatever other faults. The UPS is available as rack and tower version.
One of the most economical and
reliable UPS systems in its class: the
Liebert GXT2 is the industry leader
in terms of dimensions, performance
and reliability.
The 0.9 power factor ensures more
power for protected devices and more
energy-efficient operation.
The optionally available MicroPOD
Output Distribution And Maintenance
Bypass Module guarantees operation
– even during planned UPS maintenance work.
Flexibility:
- Up to six battery backed-up outputs
- Free swivel display panel
- Automatic frequency scanning
- Installation flexibility:
- Several communication options
(SNMP/WEB & USB)
- Compatible with Liebert MultiLink,
Liebert Nform, Liebert Multiport
and the Liebert Intellislot Relay
Interface card
Higher availability
- Advance early warning of UPS
system status
- 4-8 minutes of battery backup
time at full load
- Scalable runtime
- Full sequenced battery testing
- User replaceable hot swappable
batteries
Lowest possible TCO (Total Cost
of Ownership)
- Power factor 0,9
- Wide input voltage range
- Intelligent fan operation
- Efficient operation
- Warranty
Ideal for:
- PCs
- Networked workstations
- Servers
- Network racks
- Big network peripheries
- VolP
The Liebert GXT3 can be configured for rack or tower installation.
The LED display swivels and can be easily read in all positions.
The Liebert GXT3 has internal batteries and can also supply up to
four external battery racks (2 U).
Emerson Network Power UPS
Liebert® GTX3, 700VA-3000VA Model specifications
Model
GXT3-700RT230 GXT3-1000RT230 GXT3-1500RT230 GXT3-2000RT230 GXT3-3000RT230
Power Rating
700VA/630W
1000VA/900W
1500VA/1350W
2000VA/1800W
3000VA/2700W
Dimensions, W x D x H - mm
Unit
497 x 430 x 85
497 x 430 x 85
602 x 430 x 85
Shipping
617 x 570 x 262
617 x 570 x 262
717 x 570 x 262
Weight - kg
Unit
16.8
16.8
23.2
28
32
Shipping
20
20
26
24
28
Input AC Parameters
Voltage Range Without Battery Operation
230VAC nominal; variable based on output load
Frequency Range
40Hz - 70Hz; Auto Sensing
Input Socket
IEC-320-C14
IEC-320-C14
IEC-320-C14
IEC-320-C20
IEC-320-C20
Output Sockets
(6) IEC-320-C13
(6) IEC-320-C13
(6) IEC-320-C13
(6) IEC-320-C13
(6) IEC-320-C13
(1) IEC-320-C19
(1) IEC-320-C19
Voltage
220/230/240 VAC (user configurable) +3%
Waveform
Sine wave
Battery Parameters
Type
Valve-Regulated, Nonspillable, Lead Acid
Quantity x Voltage x Rating
4 x 12V x 5,0Ah
4 x 12V x 7,2Ah
4 x 12V x 9,0Ah
6 x 12V x 9,0Ah
Recharge Time
3 hours to 90% capacity after full discharge with 100% load till UPS auto-shutdown (Internal Batteries Only)
Battery Backup Time
See table below
Environmental
Operating
0°C to 40°C (32°F to 104°F)
Storage Temperature
-15° to 50°C (5°F to 122°F)
Relative Humidity
0% RH to 90% RH, non-condensing
Operating Altitude
Up to 3000m (10,000 ft.) at 40°C (104°F) without derating
Audible Noise
‹ 45 dBA max at. 1 meter
‹ 46 dBA, at 1 meter 3.2ft from the rear
3.2ft front and side ‹ 48 dBA max. at 1 meter 3.2ft front and side
‹ 46 dBA, at 1 meter 3.2ft from the front or sides ‹ 46 dBA, at 1 meter
‹ 48 dBA, at 1 meter 3.2ft rear
3.2ft rear
Agency
Safety
IEC/FN/AS 62040-1-2008
RFI/FMI
IEC/FN/AS 62040-2 2nd Fd=CISPR22 Class A
Surge Immunity
IEC 62040-2 2nd Fd
Transportation
ISTA Procedure 1A
Compliance
Order no.
06.099.070.1
06.099.071.1
06.099.072.1
06.099.073.1
06.099.075.1
Order no. SNMP Card
06.099.039.1
Order no. Relay Card
06.099.037.1
Bundles
06.099.170.1*
06.099.171.1*
06.099.172.1*
06.099.173.1*
06.099.175.1*
Liebert® GXT3 Battery Cabinet Specifications
Model
GXT3-700RT230 GXT3-1000RT230 GXT3-1500RT230 GXT3-2000RT230 GXT3-3000RT230
Used w/UPS Model
GXT3-48VBATT
GXT3-VBATT
Dimensions, W x D x H - mm
Unit
497 x 430 x 85
602 x 430 x 85
Shipping
617 x 570 x 262
717 x 570 x 262
Weight - kg
Unit
32
42
Shipping
35
46
Batteries
Type
Valve-regulated, nonspillable, lead acid
Quantity x Voltage x Rating
2 x 4 x 12V x 9.0Ah
2 x 6 x 12V x 9.0Ah
Environmental
Operating / Storage Temperature, °C
0°C to 40°C (32°F to 104°F) / -15°C to +40°C (19°F to 104°F)
Relative Humidity
0% to 95%, non-condensing
Maximum Operating Altitude
Up to 3000m (10,000 ft.) at 104°F (40°C) without derating
Agency
Safety / Emissions
EC/EN/AS 62040-1-1:2008 / FCC Part 15, Class A=CISPR22 Class B
Transportation
ISTA Procedure 1A
Order no.
06.099.074.1
06.099.076.1
Order no. Bundles
06.099.174.1*
06.099.176.1*
*incl. 19” installation set
Battery runtime chart (runtimes in minutes; with fully charged batteries; ambient temperature 25 °C)
Number of batteries
Internal Battery (full load)
Internal Battery + 1 External Cabinet
(full load)
Internatl Battery + 2 External Battery Cabinets
(full load)
Internatl Battery + 3 External Battery Cabinets
(full load)
Internatl Battery + 4 External Battery Cabinets
(full load)
700VA
6
50
1000VA
4
27
1500VA
4
24
2000VA
4
15
3000VA
4
18
82
58
48
29
44
116
78
82
45
62
140
109
100
64
84
Technical support
Always at your disposal: Our commitment to your business, provided by
our technical support in five languages (English, Spanish, French,
Italian, German).
Free: 00-80011554499
Subject to a charge: +39 02 98250222
[email protected]
Although much time and effort went
into ensuring that this brochure is
accurate and complete, the Liebert
Corporation does not accept responsibility for its content and does not
accept any form of liability for damages
that may result from the use of this
information, nor does it accept responsibility for errors or omissions.
© 2010 Liebert Corporation.
All rights reserved worldwide. Specifications may change without prior
notice.
GXT3M-FLY-EN-0210-01
Emerson Network Power™
Leading global provider of
Business-Critical Continuity™ solutions.
■ AC Power
■ Connectivity
■ DC Power
■ Integrated Computing
■ Embedded Power
■ Infrastructure Management &
■
■
■
■
■
■
Monitoring
Outside Plant
Power Switching and Regulation
Precision Cooling
Racks and Integrated Enclosure
Services
Overvoltage Protection
Emerson Network Power.com
Emerson, Business-Critical Continuity™
and Emerson Network Power
trademarks of Emerson Electric
Co. or affiliated companies.
© 2010 Emerson Electric Co.
Emerson Network Power UPS
Liebert GTX2 6000 VA - 10000 VA
True-Online-Power – Full energy
for your company
This is an individually configurable high-performance UPS with
proven reliability, equipped with internal hot-swap batteries and
extendable back-up time in the compact rack and tower design.
The functions and flexibility of the GXT2 make this UPS the optimum solution for your server or data centers, and for networks and
telecom systems that require a reliable, uninterrupted supply with
quality power.
USV20097
As a true online (continuous transducer) UPS, in addition to power
factor correction, frequency conversion and unlimited extension
options for external batteries, the GXT2 also provides automatic and
manual internal bypass functions, as well as an optional external
maintenance bypass. The Liebert GXT2 has all the functions required
to protect company-critical equipment against all power supply
problems.
Areas of application
Most important benefits
LAN and WAN servers
Cluster network components: hubs, routers, bridges
Remote telecommunication units
Internal telecommunication systems
Voicemail and e-mail servers
Test and diagnostics systems
Engineering network servers
Protection of industrial, microprocessor-controlled equipment
Company-critical equipment
Online VFI technology with sine wave output
Extendable battery options for long back-up times
Communication via USB, serial ports and networks
Input with power factor correction
Highly-sensitive early warning-shut down via MultiLink software
At least five minutes battery-supported operation
Settings, voltage and frequency according to individual configuration
Hot-swappable - user can change batteries
Cold start via battery
UPS remote monitoring via SNMP/Web card
Optional bypass rack for easy maintenance
True-Online-Power – Full energy
for your company
Emerson Network Power UPS
Status displays and control elements
Top panel
Top cover
(2-piece, only for
tower set-up)
Bottom panel & battery section cover
REPO connection
Relay card slot
Fans
Slot-in serial card
(SNMP, OCWEB, USB)
DB-9 communication
port
Battery
separator
switch
Connection for external
batteries
UPS output circuit breaker
Swap-out power
distribution unit
GXT2 rack model (version show: 5U, 4500-6000VA)
Most important benefits
There is no switchover time with a continuous transducer
UPS.
If the mains power fails, the critical load is fed seamlessly
by the GXT2.
For optimum usage the GXT2 can be adapted to your
requirements with a specially developed software package.
The GXT2 is available in the power classes 700, 1000, 4500
and 6000 VA. Batteries that the user can swap out ensure
low maintenance operation. And you will find all of this in
one of the most economical UPS systems in this class.
Quality power
The Liebert GXT2 is a “True Online” power source. Whatever
the quality of the inbound mains power, the clean sine wave
output meets the highest requirements of your equipment.
In contrast to other UPS technologies, the GXT2 is equipped
to overcome all potential power supply problems.
Spikes and transient overvoltages
EMI and RFI faults
Voltage drops and undervoltages
Harmonic waves
Power factor corrected loads
Power failures
Integrated reliability
The GXT2 is configured in all areas for maximum reliability.
It consequently has functions that you will search in vain to
find with other systems in the same price class:
• Power factor corrected loads:
The GXT2 maintains stable output voltage, even with
power factor-corrected consumers, which are so typical
for modern IT environments.
• Frequency conversion:
For 60Hz input/50Hz output or 50Hz input/ 60Hz output
without any power losses.
• Unlimited connection options for external batteries:
Any amount of 2U/4U battery racks can be connected to
achieve additional back-up times.
• Internal automatic and manual bypass:
Guarantees uninterrupted switchover of the power supply
for maintenance purposes.
• Optional maintenance bypass and output:
Power distributor: Enables problem-free installations and
safe routine maintenance on the UPS or connected
devices.
Emerson Network Power UPS
Communication for power supply monitoring and control
The GXT2 provides an extensive range of communication options that correspond with the control and monitoring requirements
of modern network and server systems.
Intellislot® SNMP/Web Card
For extended UPS communication and control the Intellislot
SNMP/Web Card provides your GXT2 with extensive SNMP and web
management. You consequently achieve a high degree of flexibility,
as you can monitor and control your UPS within the network.
This adapter can also be easily configured for a standard SNMP
implementation, and can be easily and efficiently shut down using
MultiLink shutdown software from Liebert without any personal
monitoring.
The SNMP/Web card monitors a wide
range of UPS information so that the
user can monitor and control the
GXT2 via the network with a standard
web browser and SNMP connection
Intellislot USB Adapter (USB CARD)
This card, which can be used during running operation, provides a USB
interface for Microsoft Windows 2000 and XP Power Management,
and consequently enables the problem-free and orderly shutdown of
the connected consumers, without having to install additional software. An approx. 2 meter cable is included in the supply schedule.
Intellislot Multiport Kit (Multiport4)
The Multiport4 Card can also be used during running operation, and
splits the UPS contact signals into 4 separate contact closure sets, which
enable the communication with the MultiLink shutdown software on
four servers simultaneously.
Intellislot Interface Kit for Relay Contacts (Relaycard-Int)
This kit provides 4 voltage-free relay contact signals for the states:
“Battery operation”, “Low battery charge”, “Bypass operation” and
“General alarm signal”. This card can be installed during running
operation via a DB25F port.
Automatic system and graphic
messages can be configured
for each UPS event.
The configuration details
appear in the lower window
section when event and
message type are selected.
MultiLink™ Shutdown Software
The GXT2 UPS system can be used in combination with the Liebert
MultiLink Shutdown software for the orderly shutdown of your IT
system. This package switches off all standard operating systems
smoothly and controlled when the UPS batteries require charging.
The MultiLink automated shutdown software has the critical task
here of protecting all information for an IT system or a network. It
is available in two versions: for individual applications and for several
systems within a network, even with multiple used operating systems.
During power failures that last for longer periods, MultiLink automatically shuts down the computer operating systems smoothly
and controlled when the UPS batteries have run low by a defined
point. MultiLink is configured to inform the users automatically.
Alarm signals can be sent to alpha-numerical pagers or can appear
directly as pop-up messages on the user’s monitor. MultiLink can
be configured for both inband and out-of-band operation. Sending
alarm and status signals via a network can significantly reduce the
costs of cabling and installation.
As an alternative to this it is possible to lay communication cables
between the individual computer systems in case a network cabling
is too problematic or expensive.
Emerson Network Power UPS
Technical Data [Liebert GXT2 tower/rack version]
Model
Power data
VA
W
Dimensions and weight
Device (WxDxH mm)
Shipping size (WxDxH mm)
Weight - device (kg)
Shipping weight (kg)
Input parameters
Frequency
Voltage range without battery operation
Frequency range
Input connection
Output parameters
Output connections
GXT2-4500RT230
GXT2-6000RT230
4500
3150
6000
4200
221 (5 U) x 547 x 430
560 x 690 x 500
67
76.5
220/230/240 VAC user-definable; 40-70Hz
176-276VAC
40-70Hz (self-detecting)
Fixed-wired
Fixed-wired + (2) IEC320-C19
Wave form and frequency
Overload warning
Battery parameters
Type
Authorized manufacturer
Number/battery blocks
Backup time
Half charge (minutes)
Full charge (minutes)
Charge time
Batteries, other functions
Battery test
Further data
Noise generation
Op. temp./height above sea level
Communication
Delivery includes
Additional components
Warranty
Standards & requirements
Safety
Additional batteries
Models
Device (WxDxH mm)
Shipping size (WxDxH mm)
Weight - device (kg)
Shipping weight (kg)
Number/battery blocks
Authorized manufacturer
Extended back-up time***
1 battery module (full/half charge)
2 battery modules (full/half charge)
3 battery modules (full/half charge)
4 battery modules (full/half charge)
Order no. UPS
Order no. UPS Set
Order no. Battery Module
Order no. Battery Module +19” Installation Set
Order no. SNMP Card
Order no. Relay Card
67
76.5
Sine wave; 50 or 60Hz nominal (50Hz specified)
>200% for 96 milliseconds; 131 - 199%
for 2 seconds; 112 - 129% for
10 seconds with switchover
VRLA, leak-proof, flame-retardant
Yuasa / REW 28-12 FR
20 x 12V x 5Ah
24
10
17
7
3 hours up to 90%
Hot-swap batteries; deep-discharge protection; black start (without mains)
Automatic, user-configurable, 7-28 days
< 55ddB
0-40°C; 0-3000m
Serial RS232 standard port, USB adapter compatible with WIN2000, XP, Apple OS, relay card and SNMP/Web card optional
User’s manual, MultiLink Software-CD; MultiLink serial cable, 3m; rack mounting handles; data carrier with configuration program
Input/output distributor
PD-CEHDWR input/output distributor
with maintenance bypass, PD-CEHDWRBYP
2 years
EMC directives, Design, EMI/EMC, Transport
GXT2-240VBATT
176 (4 U) x 522 x 430
560 x 690 x 455
65
76
20 x 12V x 9.0Ah
Yuasa / REW 45-12 FR
31 / 70
54 / 120
80 / 164
106 / 208
21 / 49
38 / 85
55 / 123
75 / 156
06.099.013.1
06.099.113.1*
06.099.014.1
06.099.114.1*
06.099.017.1
06.099.117.1
06.099.039.1
06.099.037.1
*UPS set incl. SNMP card + install. set
GXT2 4500 - 6000 in rack and tower version
Although much time and effort went into ensuring that the information in this brochure is correct and complete, Knürr/Liebert HIROSS Emerson Network Power declines all responsibility and does not accept any form of liability
for damages that may result from the use of this information, nor does it accept responsibility for errors or omissions. All rights reserved worldwide. Subject to change without prior notice. All names mentioned are trademarks or
registered trademarks of the respective owner. The Emerson logo is a trademark and a service mark of Emerson Electric Co.
Emerson Network Power UPS
Systems for qualit y power
GXT2 10000R230
For applications with extreme
heat density
Benefits
Online VFI technology with sine wave output
Parallel configuration for power increase or providing
redundancy
Extendable battery options for long back-up times
Communication via USB, serial ports and networks
Input with power factor correction
Highly-sensitive early warning-shut down via MultiLink software
Settings, voltage and frequency according to individual
configuration
Hot-swappable - user can change batteries
Cold start via battery
UPS remote monitoring via SNMP/Web card
Compact design in 3 U + 3 U format
Available as configuration of 1, 2, or 3 units to provide full
power or as 1+1, 2+1 or 1+2 redundancy
Applications
Blade Server
Pizza Box Server (1 U)
LAN and WAN network server
Cluster network components: hubs, routers, bridges
Voice over IP (VoIP) switch and router
Internal telecommunication systems
Voicemail and e-mail servers
Test and diagnostics systems
Protection of industrial, microprocessor-controlled equipment
Company-critical equipment
Liebert GXT2 10000R230
Uninterruptible power supply in compact
design for environments with extremely
high heat densities
With its compact format (6 U) and special features, which are
among the best in their class, the new Liebert GXT2 10kVA from
Emerson Network Power is the ideal solution for reliably supplying
blade servers, pizza box servers, Voice over IP equipment and other
data center and network systems in standard 19-inch racks with
power.
Its redundant configuration option makes the Liebert GXT2 10kVA
a modular and scalable solution that adjusts perfectly to your
requirements. Utilize the 1+1 or 2+1 configuration with up to
20kVA to produce clean power for your applications and an additional 10kVA as reserve, or operate three modules parallel for
loads of up to 30kVA.
This is an individually configurable high-performance UPS with
proven reliability, equipped with internal hot-swap batteries and
extendable back-up time in the compact rack and tower design.
The Liebert GXT2 10kVA Rack Version is part of the Emerson
Network Power Adaptive system solution for precision thermal
management and uniterruptible power supply and was developed
for the Liebert X-treme solutions.
Emerson Network Power UPS
LED display & control elements
Technical data [Liebert GXT2]
Model
Power data
VA
W
Dimensions and weight
Device (WxDxH mm)
Shipping dimensions (WxDxH mm)
Weight - device (kg)
Protective range
Color
Input parameters
Frequency
Voltage
Voltage range without battery operation
Frequency range
Input power factor and THDI
Input-output connections
Wave form
Overload warning
Short circuit current (A) for 5 cycles
Level of efficiency
Noise generation
Operating temperature
Relative humidity
Communication interface
optional
Battery extension, external
Model
Dimensions (WxDxH mm)
Weight (kg)
Extended back-up time
1/2/3/4 batteries (full charge)
1/2/3/4 batteries (half charge)
Number of batt. (/ battery blocks
Battery test
Warranty, standards
and approvals
Warranty
Standards and approvals
Safety
EMI / EMC
Design
Transport
Top panel
UPS Module
GXT2-10000R230
10000
7000
Battery module
410x630x130x (3 U)
27 (UPS without batteries)
IP20
RAL 9005, black
50/60 Hz (automatic detection)
230V L-N single-phase L, N,G
176-276V
±5%
0.97 - <5%
Fixed wired
Sine wave
125% - 1 minute, 150% - 10s, 300% - 2s
160A peak value
92%
<55dBA
0 - 40°C (with battery)
-25 - +55°C (without battery)
0 - 90% non-condensing
Serial RS232D89, relay card, SNMP/Web
GXT2-240RVBATT
410x630x130x (3 U)
67
Bottom panel
Relay card
SNMP. USB
Connections
Serial RS232
Input/output
Battery connections
6/16/26/36
13/35/60/90
Yuasa: NPW 45-12 / REW 45-12
(20x12V / 45W / 9Ah)
Automatic, configurable, 7-28 days
2 years
CE conformity marking
IEC / EN 62040-1-1
CE Low Voltage Directive 73/23/EEC
IEC / EN 62040-2 - Class A
CE EMC Directive 89/336/EEC
IEC 62040-3 VFI-SS-111
ISTA Level 1A
Order no. UPS + 19” Installation Set
Order no. UPS Set*
Order no. Battery Module +19” Installation Set
Order no. SNMP Card
Order no. Relay Card
06.099.016.1
06.099.116.1
06.099.019.1
06.099.039.1
06.099.037.1
* incl. Battery Module + SNMP Card + 19” Installation Set
The approximate discharge times are given in minutes and for 25°C with resistive load.
Although much time and effort went into ensuring that this brochure is accurate and complete,
Emerson Network Power does not accept responsibility for its content and does not accept any
form of liability for damages that may result from the use of this printed information, nor does it
accept responsibility for errors or omissions. All rights reserved worldwide. Changes possible
without prior notice. All names and/or entered trademarks are the property of the respective
owner.
GXT2 10000R230
Although much time and effort went into ensuring that the information in this brochure is correct and complete, Knürr/Liebert HIROSS Emerson Network Power declines all responsibility and does not accept any form of liability
for damages that may result from the use of this information, nor does it accept responsibility for errors or omissions. All rights reserved worldwide. Subject to change without prior notice. All names mentioned are trademarks or
registered trademarks of the respective owner. The Emerson logo is a trademark and a service mark of Emerson Electric Co.
Knürr RMS Compact II ®
Knürr
RMS Compact II
®
Knürr RMS Compact II ®
Knürr RMS Compact II ®
Damage prevention with checks and controls
System and network management
requirements mean the systems’
ambient conditions must be monitored. Reliability and system
availability are indispensable.
Compliance with the required
ambient parameters is extremely
important for the fault-free operation of high-grade components.
Inadmissible fluctuations in temperature or humidity often cause
hardware defects. Constant automatic monitoring of these
parameters is therefore a basic
requirement for ensuring properly
functioning operability. With the
rack monitoring systems offered by
Knürr, this information can be
Rapid fault-finding and removal is
extremely valuable! The ability to
connect additional sensors to monitoring systems not only allows
This recording is not, however, suffi- racks to be monitored – so too can
cient to ward off damages. For short complete rooms or building sections.
response times when faults occur, it All important environmental
parameters of a system can conseis helpful if the monitoring system
quently be recorded and evaluated
can perform actions automatically
in a simple and straightforward way.
(e.g. activate additional fans).
recorded and forwarded directly to
a higher-level management system, e.g. Nagios light form.
When defined incidents occur, the
Knürr RMS Compact II® can immediately send a message as an
‘SNMP trap’ to the management
system or directly as
an e-mail to a technician or an SMS
gateway.
The advantages of Knürr’s modern
rack monitoring system:
•
•
•
•
Guarantees fault-free operation
Detects disturbances early
Logs incidents
Makes service assignments easier with automatic
monitoring
• Activates countermeasures in the event of a fault
• Central control of consumables (filters, paper,
toner, meter readings, inspection intervals, etc.)
• Connection of up to 12 sensors in any arrangement
Knürr RMS Compact II ®
Knürr RMS Compact II®
■ Description
- Compact construction - Zero unit solution
(for mounting outside the 19” installation
area)
- 19” installation with adapter bracket
- Safe clamping of all connected cables with
integrated cable clamping bracket
- Cost-effective orderly installation with Plug
& Play concept
- Convenient cabling with RJ45 sensor
- TCP/IP connection via Ethernet (10/100 Base T)
- Configuration via SNMP and web browser
- Web access is password-protected and
optionally encrypted (https)
- 3 different user levels
- Freely programmable filter system (boolean
logic) for implementing all alarm conditions
- Compatible with standard network management systems – HPOpenView,
Cabletron Spectrum, Castlerock, IBM
Netview, IBM Tivoli, MG-Soft, Compaq
Insight Manager, SUN NetManager, etc.
- Sensors for monitoring all current environmental influences (optional)
- Internal power supply for sensor equipment
(no additional power supply necessary)
- Alarms via LEDs, relay, network management
or e-mail (SMTP)
- Syslog support for continuous external data
storage
- System time balancing with NTP servers
RMS20013
RMS20015
RMS compact-specific
■ Approvals
- CE Symbol in acc. with Low Voltage Directive
73/23/EEC, EMC directive 89/336/EEC
■ Color
- RAL 7021 dark gray
■ Supply schedule
1 Knürr RMS Compact II
1 power supply
2 19” mounting brackets
1 power supply mounting bracket
1 CD ROM (with manual, MIB file)
■ How supplied
- Flat-packed kit
W
H
D
Model
Order no.
UP
350
42
170
RMS Compact II®
06.108.200.8
1 set
■ Technical data
- Humidity measuring range, 30-90%
- Accuracy: +/- 5%
ECO Temperature Sensor
LUF20069
■ Technical data
- 12 universally usable sensor inputs for temperature sensors, humidity sensors, digital
(on/off) or analog sensors (0...10V)
- 3 digital outputs (2 x relay, max. 3A at
230VAC, 1x 750mA at 48VDC)
- Power supply: 100 – 240 VAC
- Operating voltage: 12VDC
■ Supply schedule
1 sensor with RJ45 port
1 mounting kit
■ Description
- Insensitive to disturbances
- No additional power supply required
- Standard cable length, 4 m
- The sensor does not have to be recalibrated
Order no.
UP
06.108.212.9
1 unit
■ Technical data
- Temperature measuring range, 0-60ºC
- Accuracy: +/- 5%
■ Supply schedule
1 sensor
1 mounting kit
W
H
D
U
h d kg
Smoke Detector
Model
Order no.
UP
ECO
06.108.220.9
1 unit
■ Description
- Optical smoke detector with VdS
approval
- For early fire detection with smoke
emission
- Power supply provided via RMS compact
- Standard cable length, 4 m
RMS20005
■ Technical data
- Operates between -20°C and +75°C
Humidity sensor
RMS20019
(similar to picture)
RMS compact-specific
■ Description
- Insensitive to disturbances
- No additional power supply required
- The sensor does not have to be recalibrated
■ Supply schedule
1 sensor with 4 m connection cable
1 mounting kit
W
H
Ø 90 75
D
Model
Order no.
UP
06.108.211.9
1 unit
Knürr RMS Compact II ®
AC Voltage Monitoring
Water sensor
■ Description
- Monitors the AC power supply via an
IEC Euro connector
- Signals status via an integrated signal
cable to the RMS Compact
RMS20033
■ Technical data
Monitored
AC voltage:
Connections:
H
D
U
h d kg
Model
■ Technical data
- Operating voltage: max. 24 VDC
RMS20031
■ Supply schedule
1 sensor with 2 m connection cable
1 mounting bracket
230 V AC 50/60 HZ
IEC plug, RJ45 socket
W
■ Supply schedule
1 sensor
1 mounting kit
W
■ Description
- Detects presence of water
Order no.
UP
06.108.222.9
1 unit
H
D
U
h d kg
Model
Order no.
UP
06.108.217.9
1 unit
Vibration Sensor
■ Description
- Detects vibrations
- Theft protection
- Reset possible via Viewer software
Door Contact Sensor
RMS20019
■ Description
- Magnet bridge sensor, works on every
magnetic conductive material (no special
mating part required)
- Can also be used for monitoring side
panels and roof
- Standard cable length, 4 m
RMS20006
■ Supply schedule
1 sensor with 4 m connection cable
W
H
D
U
h d kg
■ Technical data
- Operates between -20°C and +70°C
- Switching voltage, max. 200 VDC
- Switching current, max. 500mA
H
D
Model
Order no.
UP
06.108.215.9
1 unit
RMS20032
UP
1 unit
■ Description
- Room monitoring with the latest stateof-the-art technology
■ Technical data
Classes A + B
- VdS approval
- Volumetric lens
range
2 - 16 m
- Long lens range
29 - 50 m
- Curtain lens range 17 - 30 m
- Manipulation monitoring
- Digital fault evaluation
- Corner or wall mounting
RMS20032
Fan speed sensor
■ Description
- No additional power supply required
- Automatic detection as analog sensor
- Does not have to be recalibrated
- Offset and alarm parameters can be
set in RMS
Order no.
06.108.213.9
Passive Infrared
Movement Sensor
■ Supply schedule
1 sensor with 4 m connection cable
1 mounting kit
W
Model
■ Supply schedule
1 sensor with 4 m connection cable
1 mounting kit
W
H
D
U
h d kg
Model
Order no.
UP
06.108.214.9
1 unit
■ Technical data
- Measuring range: 0 to 0.8 l/s
- Non-linear measurement, values table:
< 0 m/s < 1 V
0 m/s 1 V
1 m/s 1.7 V
2 m/s 2.9 V
3 m/s 4.1 V
4 m/s 5 V (6 V max.)
■ Supply schedule
1 sensor with 4 m connection cable
1 mounting kit
W
H
D
20
39
9
U
h d kg
Model
Order no.
UP
06.108.218.9
1 unit
Dimensions in mm: W
H
D
h
d
L
Conversion:
=
=
=
=
=
=
Width
U
Height
1U
Depth
UP
installation height kg
useful depth
length
1 mm = 0.03937 inch
=
=
=
=
standard height unit
44.45 mm
unit of packaging
weight
= Express item
1 kg = 2.2046 pound
Liebert Nform
TM
Liebert Nform
Monitoring Software
TM
Liebert Nform
TM
Liebert Nform
TM
Increased reliability and energy efficiency with Emerson
Network Power Monitoring solutions
Data centers are becoming more
and more important in modern
companies and today’s society. The
requirements for increasingly better
IT infrastructures rise rapidly as a
result. Demands are made here for
the highest possible performance
with very high efficiency at the
same time. These requirements
appear difficult to meet because
alone the server cooling in many
data centers uses up as much
energy as the operation itself.
An integrated monitoring is
needed to increase profitability
while also reducing costs, especially with increasing complexity.
Liebert NformTM helps to meet these requirements:
What is Liebert NformTM?
• Liebert NformTM is a DC monitoring software especially for
Liebert infrastructure systems
with trend analysis function,
alarm management and results
notification.
What can NformTM do?
•Liebert NformTM provides uniform
monitoring interface and therefore an overview of the operative
status of a large number of
devices, such as:
- PDUs: Liebert MPX®, Liebert
MPH®, Knürr DI-STRIP® RM
•Uninterruptible Power Supplies
•Water-cooled racks, such as:
- Knürr CoolLoop®, Knürr
CoolTherm®
•Thermal equipment
•Environmental monitoring systems,
such as
- Knürr RMS Compact II®
Liebert Nform
What are the customer benefits?
• Liebert NformTM is an easy to
install and use management
suite that does not require complicated adjustments.
• The integration of all infrastructure components, from PDUs to
RMS compact II right through to
water-cooled server racks is very
easy, despite the high number of
monitoring data points.
• Liebert NformTM supports a
whole range of state-of-the-art
features:
- Dashboard: The system has a
configurable start page on
RMS20013
TM
which various graphics transparently illustrate the status.
- Separable window content for
transparent presentation on
several monitors
- Trending enables the storage
and graphic presentation of
historical data
- Optional automatic device
actions if an error occurs;
application execution, setting
device parameters (e.g. cooling), shutting down servers
and much more.
- Internationalization enables
installation in various languages
Liebert Nform
TM
TM
Liebert Nform – Software
Function
Order no.
Express Edition
06.108.502.0
Standard Edition
06.108.504.0
Enterprise Edition
06.108.506.0
Number of remote management stations
Unlimited
Unlimited
Unlimited
Users and groups
Unlimited
Unlimited
Unlimited
Windows XP, Windows 2003/08
Server, Windows Vista
Windows XP, Windows 2003/08
Server, Windows Vista
Windows XP, Windows 2003/08
Server, Windows Vista
Internationalization
✔
✔
✔
Automated device searches
✔
✔
✔
Data logger
✔
✔
✔
Only Nform-internal database
Only Nform-internal database
Nform-internal and Microsoft SQL
Configured dashboard
✔
✔
✔
Data and alarm export
✔
✔
✔
Online help
✔
✔
✔
Supported operating systems
SQL monitoring
Real-time monitoring and control
Regular device query
✔
✔
✔
Number of delivered device licenses
30
30*
100*
UPS/PDU web card integration
✔
✔
✔
Maximum number of devices
30
4800
Unlimited
✔
✔
✔
All Liebert UPS, Power and Cooling
systems that support SNMP
All Liebert UPS, Power and Cooling
systems that support SNMP
All Liebert UPS, Power and Cooling
systems that support SNMP
Open architecture – 3rd party SNMP monitoring
Supported devices
Parametered data logging
✔
✔
✔
Setpoint climate control
Yes
Yes
Yes
Mform window goes to the front
✔
✔
✔
Sound is played
✔
✔
✔
E-mail message
✔
✔
✔
Execute external commands
✔
✔
✔
Write file
✔
✔
Alarms and actions
Standard actions
✔
MultiLink Shutdown Clients
Unlimited including
✔
Set Data on Event
✔
Get Data Graph on Event
Access to technical information, software support website, 24-hour tele-support
software updates, tool for device integration
Software services
Number of supported device licenses
First year
1 year
30
30*
incl.
inc.
100*
incl.
06.108.531.0
06.108.534.0
06.108.537.0
3 years
06.108.532.0
06.108.535.0
06.108.538.0
5 years
06.108.533.0
06.108.536.0
06.108.539.0
✖
06.108.505.0
06.108.505.0
* Upgrades available!
Upgrades
to Nform 4.0
Upgrades and software services
Higher number of monitored devices
Order no. for device license
Order no. for software services: Access to technical information, software support website,
24-hour tele-support, software updates, tool for device integration
3 years
5 years
30
06.108.513.0
06.108.540.0
1 year
06.108.541.0
06.108.542.0
100
06.108.521.0
06.108.543.0
06.108.546.0
06.108.545.0
500
06.108.525.0
06.108.546.0
06.108.547.0
06.108.548.0
Knürr @Lock ®
Knürr @Lock
®
Knürr @Lock ®
Problems with locking systems
■ Unauthorized access
- By own employees
- By external companies
- Uncontrolled access
- Decentralized access authorizations
- Key problem
- Loss of key
- Single key system
- Many different keys
The mechanical/electro-mechanical comparison
MIR20107
■ Cylinder lock systems
+ Simple technical version
+ Cost-effective with individual locking
+ No power supply required
- Easily duplicated
- Replacement (among other factors) problematic
- Code conversion expensive with locking systems
- Key-connected, which means transferable
with key hand-over (theft)
- Logging and monitoring very
expensive/time-consuming
■ Electronic systems
+ Various locking options
+ Opening permission possible without a key
being required
+ Opening permission can be granted/withdrawn almost immediately
+ Lock control / logging possible
+ Remote opening per PC / Internet / mobile
phone / SMS
+ Expandable and easy code conversion lock
system
- Power supply required
Locking solutions
Control components to choose from
■ Electronic locking systems
■ Mechanical combination lock
■ Standard locking with half-cylinder
MIR20113
MIR20285
MIR20134
Knürr @Lock ®
Modules
Control components for electronic locking systems
■ Transponder
■ Network (server)
Interlocking: security with multi-point interlocking
mechanism
MIR00423
Decentralized rack suite
- Each rack/each door can be opened separately
– via own address
■ Access authorization administration
■ Access monitoring
■ Locking mechanism control
■ Access logging
MIR20102
Knürr @Lock ®
Embedded solution
■ Administration
■ Monitoring
■ Logging
■ Remote access
●
●
Network
●
●
LAN
●
●
WAN
●
●
Internet
MIR20099
Individual Locking / Stand-Alone Solution
■ Access authorization administration
■ Monitored access
■ Locking mechanism control
■ Access logging
MIR20094
Knürr @Lock ®
Knürr @Lock®
Strong points
■ The very small and modular design means that
no additional space or greater installation
depths are required in the rack.
■ Contacts for emergency power supply that can
be activated externally using trade standard
batteries are integrated into each swing handle.
■ An integrated light-emitting diode signals
with different colors to inform whether or not
the current access is authorized.
■ Each device of the series can be networked
with the other devices, which results in
numerous possible combinations and
options.
■ Every opening process can be logged in the
network. Existing network structures can be
used for networking.
MIR20109
Knürr @ Lock® Swing Handle
Security for racks in the data and networking area
–
–
–
–
–
–
–
MIR20284
Conventional keys are replaced by electromechanical locking components.
A servomotor pulls the retaining awl back
and releases the handle.
Actively opening the door is, however, made
with the hand as before.
Easy exchange of the swing handle with later
installation using unchanged installation
opening.
Intended for standardized installation openings
of conventional swing handle.
Can be quickly and easily upgraded to locking system.
Convenient administration of access authorizations.
■ @Lock Swing Handle, HID/IP
- The swing handle opens after a registered
transponder card has been read.
- With the HID variant, the communication
between swing handle and PC runs via a
junction box and a server.
- The IP swing handle, by contrast, is configured
via an IP address and is connected directly via
the network to the PC.
- Up to 2,048 HID cards per swing handle can
be configured using a registered master
card.
- Configuration of the cards via the network is
also possible with the included software.
■ Technical data
@Lock Swing Handle, HID
(optional IP remote connection)
- 100...240VAC, power supply not included in
the supply schedule
- Operation with 12VDC/40mA (max. 430mA)
- Multi-color status – LED
- Real-time clock
- Network communication is made via external
server (gateway)
- Up to 250 handles can be administered per
server (IP address)
■ @Lock Swing Handle, HID/IP
- 100...240VAC, power supply not included in
the supply schedule
- Operation with 12VDC/40mA (max. 430mA)
- Multi-color status – LED
- Real-time clock
- Network communication with cabled connection via integrated Ethernet 10/100 Base T
■ Function
- Opens after reading a registered card
- Memory for 32 time segments
- Memory for 2,048 cards per handle
- Integrated logbook for 500 events
- Result-related communication
- 125 kHz transponder with unique code
(HID 26 bit system)
■ Supply schedule
@Lock Swing Handle, HID
1 swing handle, HID
1 reader
1 reader connection cable
1 network node, CX2001
1 network cable, CN2001
■ Supply schedule
@Lock Swing Handle, IP
1 swing handle, IP
1 reader
1 reader connection cable
1 data CD
Knürr @Lock ®
Knürr @Lock® Server
The @Lock Server is the interface between the
HID swing handles connected via the RS485
cable and the network connected via X-Port. It
is used for intermediary storage of results and
tasks and can administer up to 250 users (swing
handle).
The @Lock Server has an integrated real-time
clock, which is buffered when power fails for up
to 1 hour.
MIR20283
■ Technical data
- Power supply: via an external plug-in power
supply, 12V (DC)
- Nominal current:
80mA (DC)
- Max. power consumption: 200mA (DC)
- Main board
Interface:
- Network interface:
- Storage space for
tasks:
- Storage space for
events:
- Max. number
swing handles
- Integ. real-time clock:
RS 485 Cable (A, B, GND,
+12V) max.
length to the
next gateway, 5m
X-Port, RJ34
plug, 8-pin
max. 10 x 250
tasks
max. 100
events
250
with buffering
of up to 60min
at 25°C
Knürr @Lock® Software “Administration Suite 2.0”
MIR20282
The @Lock software is the user interface for
controlling and configuring the @Lock Swing
Handle. Using this software, the administrator
can create access codes and HID cards and
assign users. The handle can be controlled in
real-time from the software platform. All
actions that are directly related with the swing
handles are stored in an SQL database (e.g.
opening, closing, granted accesses and accesses
rejected on the basis of non-authorization).
■ Technical data
- MS-Windows 2000/NT etc.
- SQL database
- TCP/IP network connection to the swing
handles
- The number of handles and gateways is only
restricted by the capacity of the computer
- Communication with swing handle via
server (gateways) or directly with @Lock
Swing Handle, IP
■ Functions/applications
- Client-server-based administration program
for the @Lock system
- Requires max. 3-4 seconds for a status update
- Administration of users and rights
- Administration of HID cards, opening of active
keys and access codes, closing, activation or
deactivation of swing handles
- Observation of authorized and unauthorized
access attempts
- Recording of all events connected with
swing handles
- Central observation of swing handle
- Combination of all swing handles and servers
- Events recording
- Optional web interface
- Supports Sarbanes/Oxley and HIPPA requirements
Knürr @Lock ®
Knürr @Lock® Desktop Reader
The transponder cards are read into the administration software using the desktop reader. This
enables the later configuration of the access
media in the system (lock plan creation). The
desktop reader is connected via the RS-232
interface with the PC on which the administration software is installed. The transponder card
is inserted in the read-out unit for reading the
transponder ID. The reading process can then
be initiated in the administration software by
hitting a key.
MIR20281
■ Technical data
- Power supply:
12V +- 10%
(DC max. 400mA)
via low voltage socket
- Nominal current: 80mA (DC)
- RS232 interface: RS 232 cable (RXD, TXD,
GND, Reader present,
PC present), 38,400 Baud
- Connection cable: (reader – read-out unit)
8-pin, 250 cm, UL
stranded wire, AWG 26
Model
Order no.
UP
@Lock Server HID
01.180.011.9
1 unit
@Lock Swing Handle HID
01.180.022.9
1 unit
@Lock Swing Handle IP
01.180.023.9
1 unit
@Lock Administration Suite 2.0
01.180.048.9
1 unit
@Lock Desktop Reader HID
01.180.028.9
1 unit
@Lock Transponder Card
01.180.040.9
1 unit
Power Supply, PMI 2001EU
01.180.035.9
1 unit
Power Supply, PMI 2001UK
01.180.036.9
1 unit
Power Supply, PMI 2001US
01.180.037.9
1 unit
Power Supply, PMI 2001 Japan
01.180.038.9
1 unit
Power Supply, PMI 2001 Australia
01.180.039.9
1 unit
Combi Lock
Security and flexibility realized mechanically
– This additional lock, the aptly named “Override”, produces a combination swing handle
with particularly special advantages.
– Innovative combination swing handle with
two activation options
– Independent opening and closing of the
swing handle via combination or cylinder lock
– Can be used for right and left closing doors
■ Installation
In the standard installation opening of the
Miracel rack doors. Quick mounting with
plug-in connections and screw fittings.
■ Technical data
- Cylinder lock
- Combination lock can be individually set
with 3 digits
- Independent activation
■ Supply schedule
1 swing handle with combi lock
1 mounting material set
MIR20095
Dimensions in mm: W
H
D
h
d
L
Conversion:
=
=
=
=
=
=
Width
U
Height
1U
Depth
UP
installation height kg
useful depth
length
1 mm = 0.03937 inch
=
=
=
=
standard height unit
44.45 mm
unit of packaging
weight
= Express item
1 kg = 2.2046 pound
Model
Order no.
UP
Combi Lock
01.137.013.9
1 unit
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement