advertisement
LR-10
Instrumental
Trainer/Recorder
This device has a serial number located on the bottom panel. Please record it and retain it for your records.
Serial number:
__________________
OWNER’S MANUAL
D01128520B
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Declaration of Conformity
Model Number:
Trade Name:
LR-10
TASCAM
Responsible party: TEAC AMERICA, INC.
Address: 7733 Telegraph Road, Montebello,
California, U.S. A.
Telephone number: 1-323-726-0303
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
2
TASCAM LR-10
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
FOR U.S.A.
TO THE USER
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
a) Reorient or relocate the receiving antenna.
b) Increase the separation between the equipment and receiver.
c) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
d) Consult the dealer or an experienced radio/TV technician for help.
CAUTION
Changes or modifications to this equipment not expressly approved by
TEAC CORPORATION for compliance could void the user's authority to operate this equipment.
IMPORTANT SAFETY INSTRUCTIONS
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
•
•
•
•
•
•
•
•
•
Do not expose this apparatus to drips or splashes.
Do not place any objects filled with liquids, such as vases, on the apparatus.
Do not install this apparatus in a confined space such as a book case or similar unit.
The apparatus draws nominal non-operating power from the AC outlet with its POWER or STANDBY/ON switch not in the ON position.
The apparatus should be located close enough to the AC outlet so that you can easily grasp the power cord plug at any time.
The mains plug is used as the disconnect device, the disconnect device shall remain readily operable.
If the product uses batteries (including a battery pack or installed batteries), they should not be exposed to sunshine, fire or excessive heat.
CAUTION for products that use replaceable lithium batteries: there is danger of explosion if a battery is replaced with an incorrect type of battery. Replace only with the same or equivalent type.
Caution should be taken when using earphones or headphones with the product because excessive sound pressure (volume) from earphones or headphones can cause hearing loss.
13 Unplug this apparatus during lightning storms or when unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord
TASCAM LR-10
3
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
ª Cautions about Batteries
This product uses batteries. Misuse of batteries could cause a leak, rupture or other trouble. Always abide by the following precautions when using batteries.
• Never recharge non-rechargeable batteries. The batteries could rupture or leak, causing fire or injury.
When installing batteries, pay attention to the polarity indications
(plus/minus (+/–) orientation), and install them correctly in the battery compartment as indicated. Putting them in backward could make the batteries rupture or leak, causing fire, injury or stains around them.
When throwing used batteries away, follow the disposal instructions indicated on the batteries and the local disposal laws. When you store or dispose of batteries, isolate their terminals with insulation tape or something like that to prevent them from contacting other batteries or metallic objects.
Do not use batteries other than those specified. Do not mix and use new and old batteries or different types of batteries together. The batteries could rupture or leak, causing fire, injury or stains around them.
Do not carry or store batteries together with small metal objects. The batteries could short, causing leak, rupture or other trouble.
Do not heat or disassemble batteries. Do not put them in fire or water.
Batteries could rupture or leak, causing fire, injury or stains around them.
If the battery fluid leaks, wipe away any fluid on the battery case before inserting new batteries. If the battery fluid gets in an eye, it could cause loss of eyesight. If fluid does enter an eye, wash it out thoroughly with clean water without rubbing the eye and then consult a doctor immediately. If the fluid gets on a person’s body or clothing, it could cause skin injuries or burns.
If this should happen, wash it off with clean water and then consult a doctor immediately.
The unit power should be off when you install and replace batteries.
• Remove the batteries if you do not plan to use the unit for a long time.
Batteries could rupture or leak, causing fire, injury or stains around them.
If the battery fluid leaks, wipe away any fluid on the battery compartment before inserting new batteries.
ª For European Customers
Disposal of electrical and electronic equipment
(a) All electrical and electronic equipment should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
(b) By disposing of the electrical and electronic equipment correctly, you will help save valuable resources and prevent any potential negative effects on human health and the environment.
(c) Improper disposal of waste equipment can have serious effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment.
(d) The crossed out wheeled dust bin symbol indicates that electrical and electronic equipment must be collected and disposed of separately from household waste.
(e) The return and collection systems are available to the end users. For more detailed information about disposal of old electrical and electronic
4
TASCAM LR-10
IMPORTANT SAFETY INSTRUCTIONS
equipment, please contact your city office, waste disposal service or the shop where you purchased the equipment.
Disposal of batteries and/or accumulators
(a) Waste batteries and/or accumulators should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
(b) By disposing of waste batteries and/or accumulators correctly, you will help save valuable resources and prevent any potential negative effects on human health and the environment.
(c) Improper disposal of waste batteries and/or accumulators can have serious effects on the environment and human health as a result of the presence of hazardous substances in batteries and/or accumulators.
(d) The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators must be collected and disposed of separately from household waste.
Pb, Hg, Cd
If the battery or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery
Directive (2006/66/EC), then the chemical symbols for lead (Pb), mercury
(Hg) and/or cadmium (Cd) will be indicated beneath the crossed out wheeled dust bin symbol.
(e) The return and collection systems are available to the end users. For more detailed information about disposal of waste batteries and/or accumulators, please contact your city office, waste disposal service or the shop where you purchased them.
TASCAM LR-10
5
Table of Contents
IMPORTANT SAFETY INSTRUCTIONS .........................2
Quick Start Guide ......................................................10
Step 1: Prepare the SD card and power .................................. 10
Step 2: Copy audio files from a computer.............................. 12
Step 3: Select the input................................................................. 12
Step 4: Connect an instrument and headphones .............. 13
Step 5: Tune the instrument........................................................ 13
Step 6: Use the effects ................................................................... 14
Step 7: Adjust the input and output levels ........................... 14
Step 8: Play along with the music ............................................. 15
Step 9: Record your performance ............................................. 17
Step 10: Record over a song (overdub) ................................... 17
Step 11: Use other functions ..................................................... 18
Step 12: Turn off the power ......................................................... 18
1–Introduction ...........................................................19
Main functions and features ....................................................... 19
Included items ................................................................................. 20
About this manual .......................................................................... 20
Intellectual property rights ......................................................... 21
About SD cards ................................................................................ 22
Precautions for use .................................................................... 22
Precautions for placement and use ......................................... 23
Beware of condensation .............................................................. 23
Cleaning the unit ............................................................................ 23
6
TASCAM LR-10
2–Names and Functions of Parts ..............................24
Right side panel ............................................................................... 30
Bottom panel ................................................................................... 32
Home Screen ................................................................................... 33
Recording screen ........................................................................... 35
Menu structure ................................................................................ 36
Using the menu ............................................................................... 37
Basic operations .............................................................................. 38
3–Preparation ............................................................39
Inserting and removing SD cards ............................................. 39
Inserting an SD card .................................................................. 39
Removing an SD card ............................................................... 40
Preparing an SD card for use ...................................................... 40
Special cases ................................................................................ 41
Card write protection ............................................................... 41
Powering the unit ........................................................................... 42
Using AA batteries ..................................................................... 42
Using USB bus power ............................................................... 42
Using an AC adaptor (sold separately) ............................... 43
Startup and shutdown .................................................................. 44
Table of Contents
Turning the power on ............................................................... 44
Setting the power to standby ................................................ 44
Setting the date and time ............................................................ 45
4–Connecting .............................................................46
Connecting monitoring equipment ........................................ 46
Connecting with a computer ..................................................... 46
Disconnecting from a computer .......................................... 47
Connecting an instrument .......................................................... 47
5–Recording ...............................................................48
Setting the location where recorded files are saved.......... 48
Setting the input functions ......................................................... 48
Adjusting the input level ............................................................. 49
Recording the input sound with the playback sound
(overdubbing) .................................................................................. 51
Overdubbing ............................................................................... 52
Starting and pausing recording automatically
Track incrementation .................................................................... 54
Manual track incrementation during recording ............. 54
Automatic track incrementation by file size ..................... 55
Dividing files (DIVIDE) ................................................................... 55
Recording duration ........................................................................ 56
6–Working with Files and Folders
(BROWSE screen) ..................................................57
BROWSE screen navigation ......................................................... 57
Icons on the BROWSE screen ...................................................... 57
File operations ................................................................................. 58
Folder operations............................................................................ 59
Delete the selected playback file (QUICK DELETE) ............. 60
7–Playback .................................................................61
Stopping playback ......................................................................... 61
Searching forward and backward ............................................. 62
Adjusting the playback volume................................................. 62
Disabling the MIC/LINE input ..................................................... 63
8–Playback Area and Playlist ....................................64
Using the PLAY MODE screen to set the playback area .... 64
Selecting a folder for the playback area (1) ........................... 65
Selecting a folder for the playback area (2) ........................... 66
Adding files to the playlist ...................................................... 67
Editing the playlist ..................................................................... 67
TASCAM LR-10
7
Table of Contents
9–Special Playback (playback control function) .....70
Changing the speed ...................................................................... 70
Changing the key ............................................................................ 70
Jump back a set amount and continue playback
10–Loop Playback/Repeat Playback/Single Track
Playback ............................................................................72
Using loop playback (standard mode) .................................... 72
Using loop playback with the playlist ..................................... 73
Turning loop playback on and off ........................................ 74
Repeat and single track playback ............................................. 75
–
Transferring songs to and from a computer .....76
Preparing audio files on a computer ....................................... 76
Copying audio files from a computer ...................................... 76
Transferring audio files to a computer .................................... 77
12–Using the built-in effects ....................................78
Turning the effects ON and OFF ................................................ 78
Setting the effect ............................................................................ 78
13–Using the tuner ....................................................80
Chromatic tuner mode (AUTO) .................................................. 81
Oscillator mode ............................................................................... 81
14–Using the Metronome .........................................82
8
TASCAM LR-10
Setting the metronome ................................................................ 82
Starting and stopping the metronome .................................. 82
15–System settings ...................................................83
System settings (SETUP) ............................................................... 83
Setting the forward/backward search speed ................... 83
Setting the automatic power off time ................................ 83
Adjusting the display contrast .............................................. 83
Setting the battery type .......................................................... 83
Restoring the default values (factory settings) ............... 84
Using QUICK FORMAT ............................................................... 84
Using FULL FORMAT .................................................................. 84
Setting the file name format....................................................... 85
File name format ........................................................................ 85
Setting the characters in the WORD item ........................ 86
16–Using the footswitch ...........................................87
Setting footswitch operation ..................................................... 87
Using the footswitch ..................................................................... 87
17–Viewing File Information ....................................88
File information page .................................................................... 88
Card information page.................................................................. 89
System information page ............................................................ 90
18–Messages ..............................................................91
19–Troubleshooting ..................................................95
20–Specifications ......................................................97
Analog audio input .................................................................... 97
Output ratings ................................................................................. 97
Analog output ratings .............................................................. 97
Control input/output ratings ................................................. 97
Audio performance ........................................................................ 98
Computer compatibility ............................................................... 98
Other specifications ....................................................................... 98
Dimensional drawings .................................................................. 99
Table of Contents
TASCAM LR-10
9
Quick Start Guide
Step 1: Prepare the SD card and power
ª Install the SD card
Insert the SD card into the SD card slot, which is inside the battery compartment on the bottom of the unit.
ª Preparing the power
Using AA batteries
Insert AA batteries into the battery compartment, which you opened when installing the SD card. This unit can use either alkaline or nickel-metal hydride (Ni-MH) batteries. It cannot recharge batteries.
Formatting is necessary if you insert a new SD card.
(Formatting will erase all the data on the card.)
For details, see “Inserting and removing SD cards” on page 39.
10
TASCAM LR-10
Using USB bus power
Connect the unit with a computer using the included USB cable.
Computer
USB
Quick Start Guide
Using an AC adaptor (sold separately)
Connect a TASCAM PS-P520 AC adaptor (sold separately), which is designed for the specifications of this unit, to the DC
IN 5V jack.
AC outlet
The
USB SELECT
screen appears, allowing you to set whether to use USB bus power or to connect the unit’s storage to the computer. Select
BUS POWER
.
TACAM
PS-P520
(sold separately)
DC plug
ª Turn the power on
Press and hold the opens.
[ª] button until the startup screen
For details about power preparations, see “Powering the unit” on page 42.
TASCAM LR-10
11
Quick Start Guide
ª Setting the date and time
Use the
DATE/TIME
item from the
MENU
to set the internal clock to the current time.
The unit uses its internal clock to include the date and time of the recording in its file.
The unit will function properly even if you do not make this setting. When you first put batteries into the unit, however, the clock will begin advancing from the default value of
2000-01-01/00:00:00 and this incorrect date and time will be added to recording files. (See “Setting the date and time” on page 45.)
Be sure to use file formats that this unit can play back. These formats include MP3 (32–320 kbps, 44.1 kHz) and WAV (44.1 kHz, 16/24-bit).
ª Connect the computer
Use the included USB cable to connect the unit to the computer.
ª Transfer files from the computer
Copy audio files to the MUSIC folder on the LR-10 drive that appears on the computer.
ª Disconnect from the computer
After using the correct procedures to dismount the LR-10 drive from your computer, disconnect the USB cable. The unit should automatically turn off.
For details, see Chapter 11 “Transferring songs to and from a computer” on page 76.
Step 2: Copy audio files from a computer
ª Prepare the audio files
Create audio files using the functions of the computer operating system or other computer software applications.
12
TASCAM LR-10
Step 3: Select the input
Set
INPUT
to
MIC
to use the built-in microphone to practice singing or playing a wind instrument, for example.
Set
INPUT
to
LINE
to use the LINE IN jack to practice playing a synthesizer or electronic piano.
For details, see “Setting the input functions” on page 48.
Step 4: Connect an instrument and headphones
ª Connect an instrument
Connect the headphones/stereo line output jack of the keyboard or other instrument to the LINE IN jack of this unit using a 3.5-mm miniplug cable.
For details, see “Connecting an instrument” on page 47.
CAUTION
To record the sound from the LINE IN jack or hear it through headphones, line input must be ON ( ). If mic input is activated, set the
INPUT
item in the
INPUT SETTING
menu to
LINE
. If the line input is OFF ( button to turn it ON ( ).
), press the ¶/MIC
Quick Start Guide
ª Connect headphones or speakers
Connect headphones or a monitoring system (such as powered speakers or an amplifier and speakers) to this unit’s
/LINE OUT jack.
For details, see “Connecting monitoring equipment” on page
46.
CAUTION
Before connecting headphones, use the OUTPUT (–) button to minimize the volume. Failure to do so could cause the sudden output of loud sounds, which might lead to hearing damage or other harm.
Step 5: Tune the instrument
Use the unit’s tuning function to tune an instrument using the
LINE IN jack or built-in microphones.
Press the TUNER button to open the
TUNER
screen.
For details, see Chapter 13 “Using the tuner” on page 80.
TASCAM LR-10
13
Quick Start Guide
Step 6: Use the effects
This unit has built-in effects. You can use these effects on the input signal and on the playback signal.
Press the EFFECT button briefly to enable the effects. The last effect setting used is activated and the
FX icon appears highlighted (light letters on a dark background).
Step 7: Adjust the input and output levels
ª Adjust the headphones volume
Use the OUTPUT (+/–) buttons to adjust the headphones volume.
When adjusting the volume, the current level appears in a pop-up at the bottom of the display.
Press this button again to disable the effects. The
FX
icon appears as dark letters on a light background.
Press and hold the EFFECT button to open the
EFFECT
screen where you can make detailed settings.
For details, see “Adjusting the playback volume” on page 62.
ª Adjusting the microphone and line input level
Use the INPUT level dial on the right side panel to adjust the built-in microphones and LINE IN input level.
For details, see Chapter 12 “Using the built in effects” on page
78.
14
TASCAM LR-10
For details, see “Adjusting the input level” on page 49.
ª Adjusting the mix
Press the BALANCE button to adjust the volume of the file that is playing. Use this function to adjust the balance between the playback sound and the sound of the input from the built-in microphones or the LINE IN jack. Press the Á button to start playback of the song. Adjust the volume of the playback sound using the VALUE (+/–) buttons. While playing the instrument, adjust the balance between the playing song and the instruments.
NOTE
The
BALANCE
setting only affects the volume when MIC or
LINE is ON ( or ). When MIC or LINE is OFF (
), changing the
BALANCE
value has no effect on the
or volume.
Quick Start Guide
Step 8: Play along with the music
This unit will output the sound input through the mic or the
LINE IN jack even when recording is not enabled. This allows you to select a song and play along after pressing the Á button.
This unit also has the following functions, which you can use as you like to make practicing your instrument even easier.
ª Use repeat playback
You can use two types of repeat playback. You can either play a loop between two set points or play an entire song and the entire playback area repeatedly.
Use the LOOP button for loop playback, which is useful for practicing a phrase repeatedly.
During playback (or when paused), press the LOOP button briefly at the point where you want to start loop playback to set the IN point. Then, press the LOOP button briefly again at the point where you want to stop loop playback to set the
OUT point and start loop playback of the interval between the points.
TASCAM LR-10
15
Quick Start Guide
Press and hold the LOOP button to open the
LOOP SET pop-up screen where you can make fine adjustments to the
IN and OUT points. Other loop playback functions include, for example, the possibility of setting up to five loops for each file when the playback area is the playlist.
For details about loop playback see “Using loop playback
(standard mode)” on page 72 and “Using loop playback with the playlist” on page 73.
For repeat playback of a single file or the entire playback area, press the MENU button to open the
MENU
screen, select
PLAY
MODE
and press the Á or ¯ button. Use the VALUE (+/–) buttons to select
1 REPEAT
or
ALL REPEAT
.
For details about repeat playback, see “Repeat and single track playback” on page 75.
ª Change the key
You can change the playback pitch (key) in semitones. Press the KEY button to show the key setting at the bottom of the display.
Use the VALUE (+/–) buttons to change the setting value.
For details, see “Changing the key” on page 70.
ª Changing the speed
You can also change the playback speed without changing the pitch.
You can, for example, reduce the speed to practice a song and gradually increase it as you become more proficient.
Press the SPEED button to show the speed setting at the bottom of the display.
After making the setting, press the HOME button to return to the Home Screen.
16
TASCAM LR-10
Use the VALUE (+/–) buttons to change the setting value.
For details, see “Changing the speed” on page 70.
Step 9: Record your performance
You can record the sound input through the built-in microphones or the LINE IN jack. Press the RECORD [–] button to start recording (except when the auto-record function is on and the input level is below the set value). Press and hold the RECORD [–] button to enable the pre-record function and put the unit into recording standby. Press the
RECORD [–] button to start recording, capturing sound up to 2 seconds before pressing the button. Press the [ª] button to stop recording.
For details, see “Recording” on page 50.
Quick Start Guide
Step 10: Record over a song
(overdub)
You can also record your performance together with the music that is playing back.
Use the  and ¯ buttons to select the song. Press the Á button while pressing and holding the RECORD [–] button to begin overdubbing.
Press the [ª] button to stop recording.
For details, see “Recording the input sound with the playback sound (overdubbing)” on page 51.
CAUTION
If you press and hold the record button, the unit will be put in recording standby with the pre-record function enabled, and overdubbing will not be possible.
TASCAM LR-10
17
Quick Start Guide
Step 11: Use other functions
This unit has other functions, including a convenient playlist and the ability to divide files, which you can use as you like.
One such function is the metronome, which can be accessed easily by pressing the METRONOME button.
For details, see chapter 14 “Using the Metronome” on page 82.
Step 12: Turn off the power
To turn the power off (put the unit in standby), press the
[ª] button and hold it until the shutdown screen appears.
18
TASCAM LR-10
Thank you very much for purchasing the TASCAM LR-10
Instrumental Trainer/Recorder. Please read this Owner’s
Manual carefully in order to maximize your use of all the unit’s features. We hope that you will enjoy using this trainer/ recorder for many years to come. Please keep a copy of this manual in a safe place for future reference.
You can also download a digital version of this manual from the TASCAM website (http://www.tascam.com/).
Main functions and features
•
•
•
•
•
•
•
Portable trainer/recorder for acoustic instruments players
Uses SD cards as recording media
Record using the built-in microphones or a connected external device
Recording 44.1 kHz, 16-bit linear PCM (WAV format) possible
Overdubbing the input signal with the audio playing back possible
Playback of 44.1 kHz, 16/24-bit linear WAV files and 44.1 kHz, 32–320 kbps MP3 files possible
Metronome functions
1–Introduction
•
•
•
•
•
•
•
•
•
•
•
Built-in effects can be applied to the input signal and the playback signal
Tuner functions
Auto recording function can detect the sound input level to start recording automatically
Recording continues automatically in a new file without pause when the maximum file size is reached during recording
Track incrementation function allows the creation of a new file when desired during recording without pause
Pre-recording (PRE REC) function allows the unit to record the 2 seconds of sound before recording is activated
Auto gain control function automatically make the microphone input level as even as possible
Limiter function automatically reduces the level suitably when the microphone input level is too high
Low cut filter for microphone input conveniently reduces low-frequency noise
VSA function allows adjustment of the playback speed in a range from 50% to 150% (in 10% increments) without changing the playback pitch
Key adjustment function allows the pitch to be adjusted by
±6 semitones (in semitone increments)
TASCAM LR-10
19
1–Introduction
•
•
•
•
•
•
•
•
•
•
•
•
Rec delay function can be used to avoid recording the sound of pushing the RECORD [º] button
Repeat playback and IN-OUT loop playback functions
Playlist function
In playlist mode, up to five IN-OUT loop playback settings can be made for each file
Divide function allows files to be split where desired
File name format can be set to use a user-defined word or the date
1/8” external stereo line input jack
1/8” line output/headphones output jack
128 × 64 pixel dot matrix LCD
Mini-B type USB 2.0 port
Can be powered by two AA batteries, USB bus power or a
TASCAM PS-P520 AC adaptor (sold separately)
Files saved on a computer can be transferred (copied) to the SD card in this unit via USB
Included items
The included items are listed below.
•
•
Take care when opening the package not to damage the items. Keep the package materials for transportation in the future.
•
•
Please contact the store where you purchased this unit if any of these items are missing or have been damaged during transportation.
• Main unit ...............................................................................................1
SD memory card (in the unit) .........................................................1
AA alkaline battery .............................................................................2
• USB cable (0.8 m) ................................................................................1
A warranty card ....................................................................................1
Owner’s manual (this manual) ........................................................1
About this manual
In this manual, we use the following conventions:
• “SD memory card” is sometimes abbreviated as “SD card.”
• The names of keys and controls are given in the following bold typeface: MENU
• Messages shown on the unit’s display are written like this:
ON
20
TASCAM LR-10
•
•
Characters that appear on a computer display are given in the following light typeface: OK
Additional information is introduced in the styles below when needed:
TIP
Useful hints when using the unit.
NOTE
Explanation of actions in special situation and supplement.
CAUTION
Instructions that should be followed to avoid injury, damage to the unit or other equipment, and loss of data.
Intellectual property rights
•
•
TASCAM is a trademark of TEAC Corporation, registered in the U.S. and other countries.
SDHC Logo is a trademark of SD-3C, LLC.
1–Introduction
•
•
•
•
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
Microsoft, Windows, Windows XP, Windows Vista, and
Windows 7 are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Apple, Macintosh, iMac, Mac OS and Mac OS X are trademarks of Apple Inc.
Other company names, product names and logos in this document are the trademarks or registered trademarks of their respective owners.
Any data, including, but not limited to information, described herein are intended only as illustrations of such data and/or information and not as the specifications for such data and/or information. TEAC Corporation disclaims any warranty that any use of such data and/or information shall be free from infringement of any third party’s intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such data and/or information.
TASCAM LR-10
21
1–Introduction
This product is designed to help you record and reproduce sound works to which you own the copyright, or where you have obtained permission from the copyright holder or the rightful licensor. Unless you own the copyright, or have obtained the appropriate permission from the copyright holder or the rightful licensor, your unauthorized recording, reproduction or distribution thereof may result in severe criminal penalties under copyright laws and international copyright treaties.
If you are uncertain about your rights, contact your legal advisor. Under no circumstances will TEAC Corporation be responsible for the consequences of any illegal copying performed using the recorder.
About SD cards
This unit uses SD cards for recording and playback.
You can use 64 MB–2 GB SD cards and 4 GB–32 GB SDHC cards with this unit.
A list of SD cards that have been tested with this unit can be found on the TASCAM web site (www.tascam.com/).
Use of cards that have not been verified for use with this unit could result in the unit not functioning properly.
•
•
Precautions for use
SD cards are delicate media. In order to avoid damaging a card or the card slot, please take the following precautions when handling them.
Do not leave in extremely hot or cold places.
Do not leave them in extremely humid places.
• Do not let them get wet.
• Do not put things on top of them or twist them.
• Do not hit them.
22
TASCAM LR-10
Precautions for placement and use
•
•
•
The operating temperature should be between 0°C and
40°C (32°F and 104°F).
Do not install in the following types of places. Doing so could degrade the sound quality and/or cause malfunctions.
• Places with significant vibrations or that are otherwise unstable
• Near windows or other places exposed to direct sunlight
• Near heaters or other extremely hot places
• Extremely cold places
• Places with bad ventilation or high humidity
• Very dusty locations
Avoid installing this unit on top of any heat-generating electrical device such as a power amplifier.
1–Introduction
Beware of condensation
If the unit is moved from a cold to a warm place, or used after a sudden temperature change, there is a danger of condensation; vapor in the air could condense on the internal mechanism, making correct operation impossible. To prevent this, or if this occurs, let the unit sit for one or two hours at the new room temperature before using.
Cleaning the unit
Use a dry soft cloth to wipe the unit clean. Do not clean the unit with a chemically treated cloth or substances such as benzene, thinner and alcohol because they might cause damage to the surface of the unit.
TASCAM LR-10
23
2–Names and Functions of Parts
Top panel
1 Display
This shows a variety of information.
2 PEAK indicator
This lights if the input signal level is too high.
3 Cursor control
Press up to use the §/BROWSE button, down to use the
¶ /MIC button, left to use the  button and right to use the ¯ button.
§ /BROWSE button (UP/BROWSE)
When the Home Screen is open, press this button to open the
BROWSE
screen.
When one of the setting screens is open, this moves the cursor up on the screen.
When the Home Screen is open, press and hold this button to open the
QUICK DELETE
pop-up menu.
¶ /MIC button (DOWN/MIC INPUT)
When the Home Screen is open, press this button to turn input from the built-in microphone or LINE IN jack ON/OFF.
When one of the setting screens is open, this moves the cursor down on the screen.
 button (PREVIOUS)
During playback or when stopped, press this button to return to skip to the beginning of the previous file.
When one of the setting screens is open, this moves the cursor to the left on the screen.
On the
BROWSE
screen, press this button to return to the higher folder level.
24
TASCAM LR-10
2–Names and Functions of Parts
¯ button (NEXT)
During playback or when stopped, press this button to skip to the beginning of the next file.
When one of the setting screens is open, this moves the cursor to the right on the screen.
On the
BROWSE
screen, press this to enter the lower folder level.
Press during recording to start recording to a new file without interruption (track incrementation).
4 Ô button (REW)
Press this button to search backward.
Press briefly to search backward to the beginning of the current file. Each time you press this button, the search speed increases.
Press and hold to search backward continuously for as long as the button is pressed. When the beginning of the current file is reached, searching stops there.
5 button (F FWD)
Press this button to search forward.
Press briefly to search forward to the end of the current file. Each time you press this button, the search speed increases.
Press and hold to search forward continuously for as long as the button is pressed. When the end of the current file is reached, searching stops there.
6 [ª] button (POWER, STOP)
Use to stop recording and playback, as well as to end recording standby.
Press during playback to pause playback. Press again when paused to stop playback.
Use also to respond “NO” to a confirmation pop-up message that appears during the operation of a setting screen.
Use to return from the
FILE INFORMATION
pop-up message when using the browse function.
Press and hold to turn the power ON or put the unit into standby.
TASCAM LR-10
25
2–Names and Functions of Parts
7 Á button (PLAY)
When the Home Screen is open, press when stopped to start playback.
Press during playback to return to a specific time and restart playback (flashback function). (See “Jump back a set amount and continue playback (flashback)” on page
71.)
When the
METRONOME
screen is open, press to start and stop the metronome.
Use during operation of a setting screen to confirm the selection of an item and to respond “YES” to confirmation pop-up messages.
Press this button while pressing and holding the RECORD
[º] button to start overdubbing. (See “Recording the input sound with the playback sound (overdubbing)” on page 51.)
8 RECORD [º] button/indicator
Press briefly when stopped to start recording. When recording, the indicator lights. When the auto record function is ON, press briefly to start recording standby.
When in recording standby, the indicator blinks.
Press and hold when stopped to enable prerecording (2 seconds maximum) and start recording standby. When in recording standby, the indicator blinks. Press during
26
TASCAM LR-10 recording standby to start recording. When recording, the indicator lights.
Press the Á button while pressing and holding this button to start overdubbing. (See “Recording the input sound with the playback sound (overdubbing)” on page
51.)
On the
DIVIDE
screen, use to execute the division of a file.
9 VALUE (+/–) buttons
Use these to change setting values. Press + to increase the value or – to decrease the value.
Press + and - buttons at the same time to set it to the default value.
0 OUTPUT (+/–) buttons
Use these to adjust the volume level of the output from the built-in speaker or the /LINE OUT jack. When using these buttons, the volume level is shown in a pop-up at the bottom of the display.
Press + to increase the volume or – to decrease the volume. q HOME button
Press to return to the Home Screen from one of the setting screens.
w Trainer buttons
In addition to the MENU button, which opens the
MENU screen, this section has seven buttons that allow direct access to various training functions. By using them, you can change their settings without having to return to the
Home Screen each time.
2–Names and Functions of Parts
r KEY button
Press to change the pitch of the playback. Press to cycle between the two modes. Use the VALUE (+/–) buttons to increase/decrease the pitch.
Adjust the pitch in semitones using the
KEY
mode.
Adjust the pitch in cents using the
FINE TUNE
mode. e SPEED button
Press to change the playback speed.
Use the VALUE (+/–) buttons to increase/decrease the playback speed. For details, see “Changing the speed” on page 70.
For details, see “Changing the key” on page 70.
t TUNER button
Press to tune the instrument.
TASCAM LR-10
27
2–Names and Functions of Parts
First, set the tuner mode to
AUTO
or
OSC
using the
[ª]button (AUTO) and Á button (OSC). Then, press the
TUNER button again and change the setting for the mode using the VALUE (+/–) button or Á button.
For details, see Chapter 13 “Using the tuner” on page 80.
y EFFECT button
Press briefly to turn the effects ON/OFF. When ON, the FX icon appears with light letters on a dark background.
The cursor starts on the last used item.
Press this button when one of the setting screens is open to return to the
MENU
screen.
Press this button when the
MENU
screen is open to return to the Home Screen.
For details, see “Using the menu” on page 37.
i BALANCE button
Press to change the volume level of the playback sound and balance playback and input signals.
Press and hold to open the
EFFECT
screen where you can make detailed settings.
For details, see Chapter 12 “Using the built in effects” on page 78.
u MENU button
When the Home Screen is open, press this button to open the
MENU
screen.
Use the VALUE (+/–) buttons to increase/decrease the playback volume.
For details, see “Adjusting the balance between playback and input signals” on page 63.
NOTE
The
BALANCE
setting only affects the volume when MIC or
LINE is ON ( or ). When MIC or LINE is OFF ( or
), changing the
BALANCE
value has no effect on the volume.
28
TASCAM LR-10
o METRONOME button
Press to use the metronome.
Press this button to cycle through the
TEMPO
,
BEAT
and
LEVEL
settings in order.
2–Names and Functions of Parts
When the playback area is set to playlist, press this button briefly to show the currently selected loop number.
If the loop range has been set, the “ ” and “ ” icons will appear under the playback position bar.
Use the VALUE (+/–) buttons to change the selected loop number (
LOOP 1
–
LOOP 5
).
Use the VALUE (+/–) buttons to change the value of each setting.
For details, see Chapter 14 “Using the Metronome” on page 82. p LOOP button
When the playback area is not set to playlist, press this button briefly to set the IN point (loop playback starting point) at the current location. Press briefly again to set the
OUT point (loop playback ending point) and start loop playback.
When the playback area is set to playlist, press and hold this button to show the loop screen.
Press the  button designate the IN point, and press the ¯ button to designate the OUT point. You can press the Â/¯ button again to change the IN/OUT point.
Use the Á and Ô/ buttons to find the location in the track where you want to set each point.
Press briefly again to turn the loop playback function OFF.
TASCAM LR-10
29
2–Names and Functions of Parts
For details, see “Using loop playback (standard mode)” on page 72 and “Using loop playback with the playlist” on page 73.
Left side panel
Right side panel
a USB port
Use this port to connect the unit to a computer using the included USB cable. (See “Connecting with a computer” on page 46.) s REMOTE jack
Connect a TASCAM RC-3F foot switch (sold separately), which is designed for use with this unit, to this 2.5-mm
TRS jack. d /LINE OUT jack
Connect headphones here or connect a stereo mini-jack cable from here to the line input jack of another audio device.
f INPUT volume
Use to adjust the input level of the built-in microphones or LINE IN jack signal.
g LINE IN jack
Use this stereo 3.5-mm (1/8”) mini jack to connect another audio device.
30
TASCAM LR-10
Rear panel
2–Names and Functions of Parts
Front panel
h DC IN 5V jack
Connect a TASCAM PS-P520 AC adaptor (sold separately), which is designed for the power requirements of this unit.
j Built-in stereo microphone (L/R)
This is an electret condenser stereo microphone. To use this microphone as the input source, set
INPUT
to
MIC
on the
INPUT SETTING
screen.
k Built-in mono speaker
Use this built-in speaker for monitoring.
This speaker is disabled when headphones are connected, when recording and when in recording standby.
TASCAM LR-10
31
2–Names and Functions of Parts
Bottom panel
Install batteries (2 AA) in this compartment to power the unit. (See “Using AA batteries” on page 42.) z SD card slot
Use to insert and remove SD cards. (See “Inserting and removing SD cards” on page 39.) l Battery compartment cover
; Battery compartment
32
TASCAM LR-10
Home Screen
The following information appears on the display when the
Home Screen is open.
1 Playback speed status
Depending on the playback speed setting, the icon appears as follows.
Normal playback speed
110–150% speed
50–90% speed
2 Loop playback/repeat playback setting status
Depending on the setting, the icon appears as follows.
: Single playback
: Repeat playback of one song
: Repeat playback of all songs
2–Names and Functions of Parts
: Loop playback
3 Key adjustment status
This shows whether key adjustment is ON or OFF.
: Key adjustment OFF
: Key adjustment ON
4 Effect ON/OFF status
This shows whether the effects are ON or OFF.
: Built-in effects OFF
: Built-in effects ON
5 MIC/LINE input ON/OFF status
These icons show whether the built-in mic and LINE IN jack inputs are ON or OFF.
: Built-in microphones OFF
: Built-in microphones ON
: Line input OFF
: Line input ON
6 Power supply status
When the unit is being operated on battery power, a battery ( ) icon is shown.
The amount of remaining battery charge is shown by the number of bars in the icon ( , , ).
TASCAM LR-10
33
2–Names and Functions of Parts
When almost no battery charge is remaining, the empty battery ( ) icon blinks. When this happens, the unit will soon switch to standby.
When using a TASCAM PS-P520 AC adaptor (sold separately) or USB bus power, the AC ( ) icon is shown.
NOTE
Even when some battery charge is remaining, a “
Battery
Low
” pop-up message might appear if you try to start recording or another operation that requires a lot of power.
7 Recorder operation status
Depending on the recorder operation status, one of the following icons appears.
ª
π
Á
Ô
¯
Â
Stopped
Paused
Playing back
Searching forward
Searching backward
Skipping to the beginning of the next file
Skipping to the beginning of the previous file
8 Playback position
This bar shows the current playback position. As playback proceeds, the darkened bar extends from the left.
9 Playback interval
This shows the loop playback IN point (starting point) and
OUT point (ending point) settings.
When a starting point is set, the “ ” icon appears at the corresponding position beneath the playback position bar.
When an ending point is set, the “ ” icon appears at the corresponding position beneath the playback position bar.
0 File information
This shows the name of the file being played back. If an MP3 file has ID3 tag information, that information is shown instead.
NOTE
ID3 tag information is title and artist name information that can be stored in an MP3 file. q Playback area
This shows the currently selected playback area.
ALL
All files in the MUSIC folder
FOLDER
All files in the selected folder
P.LIST
All files added to the playlist
34
TASCAM LR-10
w Elapsed time
This shows the elapsed time of the currently playing file
(hours: minutes: seconds). e Remaining time
This shows the remaining time of the currently playing file
(hours: minutes: seconds). r Playback file number/total number of files
This shows the total number of files in the playback area and the current file number. t Level meter
When MIC or LINE is ON ( or volume level of the input signals.
), this shows the
If the input level becomes too high, an indicator appears briefly at the right end of the meter.
When MIC or LINE input is OFF ( appears here.
or ),
OFF
2–Names and Functions of Parts
Recording screen
When recording or when in recording standby, the screen appears as follows.
1 Playback speed status
Depending on the playback speed setting, the icon appears as follows. The recording speed, however, cannot be changed.
Normal playback speed
110–150% speed
50–90% speed
2 Prerecord or auto record function status
When prerecording is enabled and the unit is in recording standby, “PRE”(
)
appears here.
When the auto record function is enabled and the unit is recording, “A.REC” ( ) appears here.
TASCAM LR-10
35
2–Names and Functions of Parts
3 Key adjustment status
This shows whether key adjustment is ON or OFF. Key adjustment is disabled during recording
: Key adjustment OFF
4 Recorder operation status
Depending on the recorder operation status, one of the following icons appears.
ª
π
º
Recording standby
Paused
Recording
5 Recording capacity
This shows the amount of the current SD card’s total capacity that is used. As the amount of remaining capacity decreases, the darkened bar extends from the left.
6 File name
This shows the name of the file that is being recorded.
7 Elapsed recording time
This shows the elapsed time of the file being recorded
(hours: minutes: seconds).
8 Remaining recording time
This shows the remaining amount of recording time available (hours: minutes: seconds) on the current SD card
9 Level meter
When MIC or LINE is ON ( or volume level of the input signals.
When MIC or LINE is OFF ( here.
or
Menu structure
), this shows the
),
OFF
appears
Press the MENU button to open the
MENU
screen. The menu contains the following items
Menu item
INFORMATION
PLAYLIST
Function
View information about files, the SD card and the system.
Edit the playlist.
PLAY MODE
Make playback interval and repeat playback settings.
INPUT SETTING
Make input settings
AUTO REC
Make automatic recording function settings.
DIVIDE
FILE NAME
FOOT SW
SETUP
DATE/TIME
Pages
See on page 88.
See on page 67.
See on page 64.
See on page 48.
See on page 53.
Divide a file.
Make file name settings.
See on page 55.
See on page 85.
Make settings related to using a foot switch as a remote control.
Make various unit settings.
See on page 87.
See on page 83.
Make date and time settings See on page 45.
36
TASCAM LR-10
Using the menu
This example shows how to use the menu to change the repeat function.
1. Press the MENU button to open the
MENU
screen.
2–Names and Functions of Parts
4. Use the VALUE (+/–) buttons to change the setting.
2. Use the §/BROWSE and ¶/MIC buttons to select the desired menu item, and press the Á button or ¯ button to open that setting screen.
5. Repeat steps 3 and 4 as necessary for the other items.
6. Press the MENU button to return to the
MENU
screen.
Press the HOME button to return to the Home Screen.
3. Use the §/BROWSE and ¶/MIC buttons to select the desired setting item. (When selected, the “
:
” becomes
“∑” and the setting value appears as light letters on a dark background.)
TASCAM LR-10
37
2–Names and Functions of Parts
Basic operations
Use the following buttons to use the setting screens.
MENU button
Press to open the
MENU
screen. Press when the
MENU screen is open to return to the Home Screen.
HOME button
When any of the setting screens is open, press the HOME button to return to the Home Screen.
§ /BROWSE and ¶/MIC buttons
Use this button to move the cursor (change the highlighted item) and to change the value of the selected item.
¯ button
Use this button to move from the
MENU
screen to the selected setting screen, to move the cursor (change the highlighted item) right on a setting screen and to open a folder on the
BROWSE
screen.
 button
Use this button to move the cursor (change the highlighted item) left on a setting screen and to close the open folder on the
BROWSE
screen.
38
TASCAM LR-10
VALUE (+/-) buttons
Use to change value of the selected item.
RECORD [º] button
On the
DIVIDE
screen, use to execute the division of a file.
Á button
Use this button to move from the
MENU
screen to the selected setting screen, and to select “YES” on a confirmation pop-up message.
[ª] Button
Use to respond “NO” to a pop-up confirmation message.
Use this also to return from the
FILE INFORMATION
popup message when using the browse function.
Inserting and removing SD cards
Inserting an SD card
The SD card slot is inside the battery compartment on the bottom of the case. Insert the SD card here.
NOTE
An SD card is already in the unit when it is purchased. You can use this SD card as is for recording and playback. There is no need to reinsert it.
1. Remove the battery compartment cover. If there are batteries in the compartment, confirm that the unit power is OFF and then remove them.
3–Preparation
2. Insert the SD card into the SD card slot in the back of the battery compartment in the direction shown in the illustration until it clicks into the place.
3. Insert the card and close the cover.
If you are using batteries, insert them first before closing the cover
TASCAM LR-10
39
3–Preparation
Removing an SD card
Press the inserted SD card in slightly to eject it.
Preparing an SD card for use
To use an SD card with this unit, you must format it by using this unit first.
1. Confirm that an SD card is inserted, and press and hold the [ª] button on the top panel of the unit to turn the power ON.
2. If a new card or a card that was formatted by a different device has been inserted in the unit, the following popup message appears.
•
•
•
CAUTION
Do not remove the SD card from the unit when it is connected to a computer by USB.
SD cards that meet SD/SDHC standards can be used with this unit.
A list of SD cards that have been verified to work with this unit is posted on the TASCAM website (http://www.tascam.
com/).
3. Press the Á button to start formatting.
Remove the SD card if you do not wish to format it.
CAUTION
Formatting will erase all the data on the card.
4. After formatting completes, the Home Screen opens.
You can also reformat a card with this unit at any time.
40
TASCAM LR-10
3–Preparation
CAUTION
When formatting, use a TASCAM PS-P520 AC adaptor (sold separately), USB bus power or confirm that the batteries have sufficient remaining power.
•
Special cases
If you insert an SD card that has been formatted by a device other than another LR-10, the
FORMAT ERROR
screen will appear. In this case, format the card to use it with this unit.
SD cards that have been formatted by a TASCAM DR series device, however, are compatible with this model.
• If the system file or another important file has been accidentally erased from the SD card when accessing it from a computer, the following pop-up screen appears.
Card write protection
SD cards have write-protection switches that prevent new data from being written to them.
Unprotected Protected
If you slide the protect switch to the “LOCK” position, file recording and editing will not be possible. Move the switch to the unlocked position in order to record, erase and otherwise edit data on the card.
In this case, press the Á button to format the card again.
TASCAM LR-10
41
3–Preparation
Powering the unit
This unit can be powered by two AA batteries, USB bus power or a TASCAM PS-P520 AC adaptor (sold separately).
This unit can use either alkaline or nickel-metal hydride
(NiMH) batteries.
Using AA batteries
As described in the “Inserting and removing SD cards” section above, this unit has a battery compartment in the bottom.
Insert 2 AA batteries into this compartment, aligning them correctly with the plus/minus indications inside, and then close the compartment cover.
When using AA batteries, set the type of battery in order to allow the unit to accurately show the amount of power remaining and determine whether enough power is available for proper operation. (See “Setting the battery type” on page
83.)
•
•
CAUTION
Manganese batteries cannot be used with this unit.
This unit cannot recharge Ni-MH batteries. Use a commercially-available recharger.
• The included alkaline batteries are provided for confirming the operation of the unit and might not last very long.
Using USB bus power
Connect the unit with a computer using the included USB cable as shown in the illustration below.
computer
USB
The
USB SELECT
screen appears if the power is ON when you make the USB connection or if you turn the power ON after making the USB connection. This screen allows you to set
42
TASCAM LR-10
whether to use USB bus power (
BUS POWER
) or to connect the unit’s storage to the computer (
STORAGE
).
3–Preparation
Using an AC adaptor (sold separately)
Connect a TASCAM PS-P520 AC adaptor (sold separately), which is designed for the power requirements of this unit, to the DC IN 5V jack as shown in the illustration.
Use the §/BROWSE button or ¶/MIC button to select
BUS
POWER
and press the Á button to provide power from the computer USB port and open the Home Screen.
CAUTION
Connect this unit and the computer directly. Operation using a USB hub cannot be assured.
NOTE
If you connect to a computer by USB, power will be supplied from the USB bus even if batteries are also in the unit.
PS-P520
(sold separately)
DC plug
AC outlet
CAUTION
Never use any adaptor other than the TASCAM PS-P520 AC adaptor (sold separately), because it is designed for the power requirements of this unit. Use of a different adaptor could cause malfunction, fire or electric shock.
NOTE
If batteries are installed and the AC adaptor is connected, power will be supplied from the AC adaptor.
TASCAM LR-10
43
3–Preparation
Startup and shutdown
®
CAUTION
Turn the volume of any monitoring system that is connected to this unit down completely before turning the unit’s power ON or putting it into standby. Do not wear connected headphones when turning the unit’s power ON or putting it into standby. Failure to follow these precautions could cause noise, which might damage speakers or harm your hearing.
Turning the power on
When the unit is in standby mode, press and hold the [ª] button until the
TASCAM LR-10
startup screen opens.
The Home Screen opens after the unit completes startup.
Startup Screen Home Screen
Setting the power to standby
When the power is ON, press and hold the [ª] button until the
INSTRUMENTAL TRAINER/RECORDER
screen appears.
44
TASCAM LR-10
3–Preparation
Setting the date and time
Using its internal clock, this unit remembers the date and time when a file is recorded.
1 Press the MENU key to open the
MENU
Screen.
2 Use the §/BROWSE and ¶/MIC buttons to select
DATE/TIME
, and press the Á or ¯ button.
USB bus power or an AC adaptor. When using batteries, we recommend that you replace or recharge them before they completely lose power.
3 Use the Â/¯ buttons to move the cursor, and use the VALUE (+/–) buttons to change values.
4 Press the Á button to confirm the change and return to the MENU screen.
NOTE
You can set the unit to automatically add the date and time to file names. (See “Setting the file name format” on page 85.)
CAUTION
The date and time setting can only be maintained for a few minutes when the unit is not powered by batteries,
TASCAM LR-10
45
4–Connecting
Connecting monitoring equipment
Headphones
Connecting with a computer
By connecting this unit with a computer, you can transfer
(copy) audio files (WAV or MP3 format) on the computer to the SD card in the unit, as well as erase files and work with folders on the card from the computer.
Use the included USB cable to connect the USB port of this unit to a USB port on the computer.
computer
USB
Powered monitor speakers or amplifier and speakers
Connect headphones or a monitoring system (such as powered speakers or an amplifier and speakers) to this unit’s
/LINE OUT jack.
CAUTION
Before connecting headphones, use the OUTPUT (–) button to minimize the volume. Failure to do so could cause the sudden output of loud sounds, which might lead to hearing damage or other harm.
When connected, the
USB SELECT
pop-up screen appears on the unit.
To exchange data with the computer, use the §/BROWSE or
¶ /MIC button to select
STORAGE
and press the Á button.
USB connected
pop-up screen appears on the screen.
(Select
BUS POWER
to power the unit from the computer USB bus.)
46
TASCAM LR-10
This unit appears on the computer screen as an external drive named LR-10.
4–Connecting
Connecting an instrument
In addition to the built-in microphone, this unit has a line in jack (stereo mini-jack) on its right side panel to which you can connect the outputs of keyboards and other instruments, as well as audio devices.
Keyboard
The LR-10 drive contains MUSIC and UTILITY folders.
Disconnecting from a computer
After using the correct procedures to dismount the LR-10 drive from your computer, disconnect the USB cable. The unit should automatically turn off.
Please refer to the operation manual for your computer system for instructions about the correct procedures for dismounting an external drive.
•
NOTE
You can apply the built-in effects to sound input by the connected instrument and play along to a song playing back on the unit or its metronome.
• To use an electric guitar or bass with this unit, connect the instrument first to an effect pedal or other device that has a headphones/line level output.
TASCAM LR-10
47
5–Recording
This unit can record a performance through the built-in mic or from a keyboard or similar instrument that is connected to the
LINE IN jack. The audio file format used for recording is always
44.1 kHz, 16-bit WAV.
In addition, this unit can also mix the input signal and an audio file that is playing back and record both together
(overdubbing).
Setting the location where recorded files are saved
You can set the location where recorded files are saved. (See
“Folder operations” on page 59.)
If you do not set a destination, files will be saved directly in the MUSIC folder.
Setting the input functions
1 Press the MENU button to open the
MENU
Screen.
2 Use the §/BROWSE and ¶/MIC buttons to select
INPUT SETTING
, and press the Á or ¯ button to open the
INPUT SETTING
screen.
48
TASCAM LR-10
This screen has the following setting items.
Use the §/BROWSE and ¶/MIC buttons to select the desired item. (When selected, the “
:
” becomes “∑” and the setting value appears as light letters on a dark background.) Use the VALUE (+/–) buttons to change the setting value.
The
GAIN
,
TYPE
,
LOW CUT
and
LEVEL CTRL
items only function when
INPUT
is set to
MIC
.
INPUT:
Set the input source to microphone (
MIC
) or line (
LINE
).
The default setting is
MIC
.
When
MIC
is selected, sets the input source as the built-in microphones.
When
LINE
is selected, sets the source as the line level signal input to the right side panel LINE IN jack (stereo mini-jack).
GAIN:
Set the built-in microphones input sensitivity as
HIGH
,
MID
, or
LOW
.
5–Recording
The factory default setting is
MID
.
Change it to
HIGH
if the input level is too low and to
LOW
if the input level is too high.
TYPE:
Set the built-in microphones to
STEREO
or
MONO
. The factory setting is
STEREO
.
If you select
MONO
, the left and right channels are combined into the same signal.
LOW CUT:
The factory default setting of the low cut filter is
OFF
, but you can also select
40Hz
,
80Hz
or
120Hz
as the cut-off frequency for a low cut filter.
LEVEL CTRL:
Use this to set the level control function.
Set it to
AUTO
to have the LR-10 automatically adjust the input gain according to the input level. Loud sounds and quiet sounds are both adjusted to the same level.
Set it to
LMT
to have the LR-10 automatically limit the input gain so that input level of loud sounds is reduced to prevent distortion.
The factory default setting is
OFF
.
3 Press the HOME button to return to the Home Screen.
•
NOTE
Try using one of the low cut filter settings when recording outdoors or another place where the unwanted sound of wind is being recorded.
•
•
When recording live performances and in other situations where unexpected loud sounds might occur, set this function to
LMT
to prevent input clipping and allow recording without distortion.
Use the LR-10’s built-in effects as necessary on the input source signal. (See “Using the built-in effects” on page 78.)
Adjusting the input level
You can adjust the level of the mic/line input.
Use the INPUT volume control on the right side panel to adjust the input level of the built-in microphones or the LINE
IN jack.
TASCAM LR-10
49
5–Recording
The PEAK indicator to the right of the display lights red just before the recording level begins to distort. Play the instrument or start playback on the connected device, and input the loudest volume you intend to record. Set the INPUT level as high as possible without making the PEAK indicator light red, and set the INPUT level as high as possible without making the PEAK indicator light red.
CAUTION
In order to hear through headphones the sound that you are recording from the built-in microphones or the line in jack, the mic/line input must be ON ( off ( or
or ). If the input is
), press the ¶/MIC button to turn it ON (
or ).
The input can be turned ON/OFF during recording.
Recording
Before following these procedures, adjust the input level and open the Home Screen.
1. Press the RECORD [º] button briefly to start ordinary recording.
When recording starts, the RECORD [º] button indicator lights and the display shows the elapsed and remaining recording times.
Press and hold the RECORD [º] button to enable the pre-record function and put the unit into recording standby. The RECORD [º] button indicator blinks when in recording standby. (See “Recording a few seconds before pushing the record button (pre-recording)” on page 51.)
2. Press the [ª] button to stop recording.
To pause recording, press the RECORD [º] button. To resume recording to the same file, press the RECORD [º] button again.
Press the [ª] button after pausing to complete the creation of an audio file with the music recorded up to the moment that recording was paused.
50
TASCAM LR-10
Recording a few seconds before pushing the record button (prerecording)
The unit can capture up to 2 seconds of input signal during recording standby, allowing recording to start before the
RECORD [º] button is pushed.
1. Press and hold the RECORD [º] button briefly to start recording standby. The RECORD [º] button indicator blinks, and the PRE ( ) icon appears on the display.
2. Press the RECORD [º] button again briefly to start recording. Input signal is recorded starting up to 2 seconds before the button was pushed.
The RECORD [º] button indicator lights when recording.
3. Press the [ª] button to stop recording.
To pause recording, press the RECORD [º] button. To resume recording to the same file, press the RECORD [º] button again.
Press the [ª] button after pausing to complete the creation of an audio file with the music recorded up to the moment that recording was paused.
5–Recording
TIP
Use this function in combination with the auto-recording function to record without missing the beginning of a performance.
NOTE
If the unit was put into recording standby less than 2 seconds before this function is used, recording will start from the time when recording standby was enabled.
Recording the input sound with the playback sound (overdubbing)
You can combine the input signal with the signal from an already recorded file being played back to record a new file.
For example, you could record a new instrument part over an existing track.
•
NOTE
When overdubbing, You cannot use the auto-record or manual file incrementation functions.
• You cannot pause during overdubbing. (The RECORD [º] button does not respond if pushed.)
TASCAM LR-10
51
5–Recording
TIP
Using the overdubbing function, you can record over the same file multiple times, allowing you to use this unit as a simple multitrack recorder.
Overdubbing
1. Use the  button, ¯ button or the
BROWSE
screen to select the file that you want to overdub.
2. Press the Á button to start playback and begin playing the instrument. Check the balance between the levels of the playback and instrument sounds.
3. Use the INPUT volume to adjust the input volume level so that the PEAK indicator does not light. Press the BALANCE button to show the BALANCE item, and use the VALUE (+/–) buttons to adjust the level of the playback sound. The range is from “
0
” (minimum) to
“
20
” (maximum), and the default value is “
20
”.
NOTE
The
BALANCE
setting only affects the volume when MIC or
LINE is ON ( or ). When MIC or LINE is OFF (
), changing the
BALANCE
value has no effect on the volume.
or
4. Press the Á button while pressing and holding the
RECORD [º] button to begin overdubbing.
CAUTION
If you press and hold the RECORD [º] button long , the unit will be put in recording standby with the pre-record function enabled, and overdubbing will not be possible.
5. When overdubbing starts, the RECORD [º] button indicator lights, and the elapsed and remaining recording times are shown on the recording screen.
In addition, the name of the file being played back is shown next to the play icon and above the name of the file being recorded.
If no file that can be played back has been selected, the following pop-up message appears.
52
TASCAM LR-10
5–Recording
6. Press the [ª] button to stop recording.
Starting and pausing recording automatically (AUTO REC)
This unit can be set to automatically start and pause recording in response to the level of the input signal.
1. Press the MENU button to open the MENU screen.
2. Use the § / BROWSE and ¶ / MIC buttons to select the
AUTO REC menu item, and press the Á or ¯ button to open the
AUTO REC
screen.
5. Press the § / BROWSE or ¶ / MIC button to select the
START LEVEL
item.
6. Use the VALUE (+/–) buttons to set the input signal detection level to
-6dB
,
-12dB
(default value),
-24dB
or
-48dB
.
3. Use the § / BROWSE and ¶ / MIC buttons to select the
MODE
item.
4. Use the VALUE (+/-) buttons to set it to
ON
.
7. After completing the setting, press the HOME button to return to the Home Screen.
8. Press the RECORD [º] button to start recording standby and RECORD [º] button indicator blinks.
Press and hold the RECORD [º] button to enable the pre-record function and put the unit into recording standby.
TASCAM LR-10
53
5–Recording
Recording starts automatically when the input signal level exceeds the detection level set using the
START LEVEL item.
Recording stops automatically and the unit returns to recording standby when the input signal level stays below the detection level set using the
START LEVEL
item for five or more seconds and RECORD [º] indicator blinks.
TIP
Use this function in combination with the pre-recording function to record without missing the beginning of a performance.
NOTE
When
AUTO REC
is ON, unlike usual, pressing the RECORD [º] button briefly does not start recording, but does put the unit into recording standby.
9. You can press the [ª] button if you want to stop a recording that has started automatically.
CAUTION
When overdubbing, the auto-recording function cannot be used.
Track incrementation
You can start recording to a new file without interruption manually. If a file reaches the maximum size (2GB), the unit will also automatically start recording to a new file. In both cases, the original file is saved and no gap occurs in the recording.
Manual track incrementation during recording
At any time during recording, you can manually start a new file and continue recording easily.
1. Press the ¯ button during recording.
•
•
•
CAUTION
A new file cannot be created if the total number of files and folders would exceed 5000.
•
Files shorter than two seconds cannot be created.
If the name of a newly created file would be the same as that of an existing file, the number at the end of the name is increased to give the new file a unique name.
When overdubbing, the track incrementation function cannot be used.
54
TASCAM LR-10
5–Recording
NOTE
When a new file is created, the number at the end of the name is increased.
Automatic track incrementation by file size
If a file reaches the maximum size (2 GB) during recording, the unit will automatically start recording to a new file. The original file is saved and no gap occurs in the recording.
CAUTION
A new file cannot be created if the total number of files and folders would exceed 5000.
NOTE
If the recording time is 24 hours or more, it will be displayed as 23:59:59.
3. Use the § / BROWSE and ¶/ MIC buttons to select the
DIVIDE
menu item, and press the Á button or ¯ button to open the
DIVIDE
screen.
4. Use the Ô and button to determine where the file will be divided, and press the RECORD [º] button.
The following pop-up message appears.
Dividing files (DIVIDE)
You can split a recorded file into two files at any position you like.
1. Use the  button, ¯ button, or
BROWSE
screen to select the file that you want to divide.
2. Press the MENU button to open the
MENU
screen.
5. Press the Á button to divide the file.
Press the [ª] button to cancel division and return to the
DIVIDE
screen.
TASCAM LR-10
55
5–Recording
•
NOTE
When the
DIVIDE
screen is open, you can press the Á button and set the divide position while playing the track.
• After dividing a file, two new files with “_a” and “_b” added to the end of the original file name are created. For example if the original filename is “LR0000_0000.wav” then the new files will be named “LR0000_0000_a.wav” (the recording before the division point) and “LR0000_0000_ b.wav” (the recording after the division point).
•
CAUTION
MP3 files cannot be divided.
• Division is not possible if the SD card has insufficient open space.
•
•
Division is not possible if the file name would become more than 200 characters long.
Division is not possible if a file that already exists has the same name as the name that would be given to a new file created by division.
Recording duration
The table below shows the approximate amount of recording time possible on SD/SDHC cards of different capacities.
1 GB
SD/SDHC card capacity
2 GB 4 GB 8 GB
Approximate recording time
(hours: minutes)
1: 41 3 : 22 6 : 44 13 : 28
•
•
•
The recording times shown above are estimates. They might differ depending on the SD/SDHC card being used.
The recording times shown above are not continuous recording times, but rather they are the total possible recording times for the SD/SDHC card.
This unit only records in 44.1 kHz, 16-bit WAV format.
56
TASCAM LR-10
6–Working with Files and Folders (BROWSE screen)
On the Browse Screen, you can view the contents of the
MUSIC Folder, which contains the audio files on the SD card.
On this screen, you can also play and erase selected audio files, create folders, add tracks to the playlist and so on. (See
“Playlist” on page 67.)
TIP
If you connect this unit with a computer by USB or connect the SD card directly with a computer, you can change the folder structure within the MUSIC Folder and erase files in it using the computer. Furthermore, you can change file names from the computer.
To open the
BROWSE
screen, from the Home Screen, press the
§ /
BROWSE button.
BROWSE screen navigation
On the
BROWSE
screen, folders and music files appear in a hierarchical structure much like they would appear on a computer. Folders can only be used to two levels.
• Use the § / BROWSE and ¶/MIC buttons to select files and folders.
• When a folder is selected, press the ¯ button to show the contents of that folder.
•
•
When a file or folder is selected, press the  key to exit the currently open folder and go to a higher level in the folder structure.
When a file or folder is selected, press the Á key to open the pop-up window.
When you open the
BROWSE
screen, the contents of the folder that contains the file that was selected on the Home Screen are shown.
Icons on the BROWSE screen
The icons that appear on the
BROWSE
Screen have the following meanings.
MUSIC folder ( )
The MUSIC Folder is the highest (root) level folder in the hierarchy shown on the
BROWSE
Screen.
TASCAM LR-10
57
6–Working with Files and Folders (BROWSE screen)
Audio file ( )
This icon appears before the names of audio files.
Folder ( )
This icon shows folders that contain subfolders.
Folder ( )
This icon shows folders that do not contain subfolders.
Open folder ( )
The contents of the folder marked with this icon are currently shown on the screen.
PLAY
Play the file and reopen the Home Screen. If the playback area is set to “FOLDER”, the playback area becomes the folder that contains that file.
INFO
Show information (date, time and size) about the selected file. Press the Á button again or press the [ª] button to return to the
BROWSE
screen.
File operations
Select the desired audio file on the
BROWSE
screen, and press the Á button to open the following pop-up menu.
ADD LIST
Add the selected file to the playlist. (See “Playlist” on page
67.)
DELETE
A message appears to confirm that you want to delete the selected file. Press the Á button to delete the file and the
[ª] button to cancel deletion.
Use the §
/ BROWSE and ¶/MIC buttons to select the desired item, and press the Á button to execute one of the following operations.
58
TASCAM LR-10
CANCEL
No operation is conducted on the selected file and the pop-up menu closes.
Folder operations
6–Working with Files and Folders (BROWSE screen)
Select the desired folder on the
BROWSE
screen, and press the
Á button to open the following pop-up menu.
SELECT
Return to the Home Screen and select the first file in the folder. This folder becomes the new playback area regardless of the previous playback area setting.
When recording, files are created in the folder selected using this operation.
CREATE
A pop-up appears to confirm that you want to create a new folder.
Use the §
/ BROWSE and ¶/MIC buttons to select the desired item, and press the Á button to execute one of the following operations.
Press the Á button to create a new folder, or press the
[ª] button to cancel the operation.
However, if you try to create a new folder inside a second level subfolder the
Layer too Deep
message appears and the folder is not made.
TASCAM LR-10
59
6–Working with Files and Folders (BROWSE screen)
ALL DEL
A pop-up message appears to confirm that you want to delete all the files in the selected folder at once.
Delete the selected playback file
(QUICK DELETE)
Use the following procedure to conveniently delete the currently selected playback file.
1. On the Home Screen, press and hold the § / BROWSE button to open the
QUICK DELETE
screen.
2. Press the Á button again to confirm deletion, or press the [ª] button to cancel.
Press the Á button to erase the files, or press the [ª] button to cancel the operation.
NOTE
You cannot erase read-only files or files that are not recognized by this unit.
CANCEL
No operation is conducted and the selected folder is left as is.
60
TASCAM LR-10
When the Home Screen is open , use Á, Â, ¯ and other buttons to operate the unit in the same way you would use a
CD player or other audio playback device.
When the Home Screen is not open, however, these buttons have different functions.
Before using the following procedures, insert an SD card that has been formatted by this unit and that contains audio files that the unit can playback.
NOTE
SD cards that have been formatted by a TASCAM DR series device can also be used with this unit.
Playback
When the unit is stopped, press the Á button to start playback.
•
NOTE
Only files in the playback area can be played.
• You can also choose files for playback by name on the
BROWSE
screen.
7–Playback
Stopping playback
When the Home Screen is open and a track is playing back, press the [ª] button to stop playback at the current position (pause).
Press the [ª] button again to return to the beginning of the file.
Selecting a file
During playback or when stopped, use the  and ¯ buttons to select a file.
Press the  button to skip to the previous file.
Press the ¯ button to skip to the next file.
Only files in the playback area can be played. (See “Using the
PLAY MODE screen to set the playback area” on page 6.)
The song name, file number and other information for the currently playing file are shown on the display.
The ª icon appears on the display when playback is stopped at the beginning of a track, and the π icon appears when playback is stopped in the middle of a track (paused).
TASCAM LR-10
61
7–Playback
Searching forward and backward
During playback or when stopped (or paused), press and hold the Ô/ button to search backward/forward. Release the button to return to the previous state.
Use the
CUE/REV SPEED
item on the
SETUP
screen to set the search speed. (See “System settings (SETUP)” on page 83.)
Press the Ô/ button briefly to search backward/ forward to the beginning/end of the file.
Press the same button again briefly to change the search speed. The speed options are: x2, x5, x10, x20, x40 and x120.
NOTE
Searching backward/forward continues only until the beginning/end of the current file. Searching will not continue into the previous or next file even if you continue to hold the button.
Adjusting the playback volume
Use the OUTPUT (+/–) buttons to adjust the volume level output from the built-in speaker or the /LINE OUT jack.
While being adjusted, the volume level is shown in a pop-up at the bottom of the display.
NOTE
If you turn the MIC/LINE input off, the playback level returns to its original level.
If the MIC/LINE input is on, and you have used the BALANCE button to lower the volume of the playback (
BALANCE
) to overdub an audio file, when you play back that file, the playback monitoring level will be lower than it was when recording. In this case, use the BALANCE button to set
BALANCE
to its maximum.
62
TASCAM LR-10
Adjusting the balance between playback and input signals
You can adjust the balance between the input sound of an instrument being played and the playback sound of a file.
Use the INPUT volume to adjust the level of the input signal, and press the BALANCE button to open the
BALANCE
item and adjust the level of the playback signal.
7–Playback
Disabling the MIC/LINE input
When you want to listen to just the playback signal, you can disable the MIC/LINE input to prevent any unwanted noise.
If you want to disable the MIC/LINE input (built-in microphones or LINE IN jack), press the¶/MIC button when the Home Screen is open so that the MIC or LINE icon appears as dark letters on a light background ( or ).
Press the ¶/MIC button again to enable the MIC/LINE input.
The
MIC/LINE
icon appears as light letters on a dark background ( or ) when input is enabled.
NOTE
If you turn the MIC/LINE input off ( in the level meter area.
or ),
OFF
appears
Adjust the volume of the playback sound using the VALUE
(+/–) buttons. The range is from “
0
” (minimum) to “
20
”
(maximum), and the default value is “
20
”.
NOTE
The
BALANCE
setting only affects the volume when MIC or
LINE is ON ( or ). When MIC or LINE is OFF (
), changing the
BALANCE
value has no effect on the
or volume.
When the MIC/LINE input is off ( or ), the
BALANCE setting is canceled and the playback level returns to its original setting.
TASCAM LR-10
63
8–Playback Area and Playlist
On the Home Screen, use the  or ¯ button to select a file from the current “playback area” to play. You can set the playback area that includes the files that can be selected. If the card contains a large number of files, for example, setting a limited playback area can make file selection easier. On the
PLAY MODE the current folder or the playlist. You can also use the
BROWSE screen to set the desired folder as the playback area.
NOTE
screen, you can set the playback area to all files,
On the
BROWSE
screen, you can also choose any file on the card for playback regardless of the playback area setting.
Using the PLAY MODE screen to set the playback area
Follow these procedures to set the playback area on the
PLAY
MODE
screen.
1. Press the MENU button to open the
MENU
screen.
2. Use the § / BROWSE and ¶/MIC button to select
PLAY
MODE
and press the Á button or ¯ button to open the
PLAY MODE
screen.
3. Select the
AREA
item so that its setting value appears as light letters on a dark background.
4. Use the VALUE (+/–) buttons to select one of the following playback areas.
ALL FILES
Allow playback of all the files in the MUSIC folder on the SD card.
FOLDER
Allow playback of all the files in the folder that contains the currently selected file.
PLAYLIST
Allow playback of the files in the playlist. (See “Playlist” on page 67.)
If you select this, but there is no playlist defined, a
No
PLAYLIST
pop-up appears.
64
TASCAM LR-10
Even if there is no playlist, you can still set the playback area to
PLAYLIST
. Doing so, however, will cause the
No
PLAYLIST
pop-up to appear every time you press the
 or ¯ button because you cannot change to another file.
8–Playback Area and Playlist
Selecting a folder for the playback area (1)
Regardless of the current playback area, if you select a folder on the
BROWSE
Screen, the playback area changes to the selected folder.
1. On the Home Screen, press the § / BROWSE button to open the BROWSE screen.
NOTE
The current playback area setting (
ALL
,
FOLDER
or
P.LIST
) is shown at the bottom left of the Home Screen.
2. Use the § / BROWSE and ¶/MIC buttons to select the desired folder (light on dark).
For instructions about using the
BROWSE
screen, see
“BROWSE screen navigation” on page 57.
3. Press the Á button to open the pop-up menu shown below.
Playback area indication
TASCAM LR-10
65
8–Playback Area and Playlist
Use the §
/
BROWSE and ¶/MIC buttons to choose the
SELECT
, and to press the Á button.
4. The Home Screen automatically reopens and the first file in that folder is selected. This folder becomes the playback area regardless of the previous playback area setting.
3. Press the ¯ button to show the contents of that folder.
Selecting a folder for the playback area (2)
If the playback area is set to
FOLDER
and you select a file on the
BROWSE
screen, the folder that contains the selected file becomes the playback area.
1. On the Home Screen, press the § / BROWSE button to open the
BROWSE
screen.
4. Use the § / BROWSE and ¶/MIC buttons to select the desired file (light on dark).
For instructions about using the
BROWSE
screen, see
“BROWSE screen navigation” on page 57.
5. Press the Á button to open the pop-up menu shown below.
2. Use the § / BROWSE and ¶/MIC buttons to select the desired folder (light on dark).
6. Use the § / BROWSE and ¶/MIC buttons to choose the
PLAY
(light on dark), and to press the Á button.
The Home Screen automatically reopens and that file starts playing back. Moreover, the folder that contains that file becomes the playback area regardless of the previous playback area setting.
66
TASCAM LR-10
8–Playback Area and Playlist
Playlist
You can make a playlist, which is a set of tracks for playback.
You can play just the tracks in your playlist by setting the
AREA
item to
PLAYLIST
on the
PLAY MODE
Screen.
In addition, when the playback area is set to
PLAYLIST
, loop playback has additional functions. (See “Using loop playback with the playlist” on page 73.)
Adding files to the playlist
1. On the Home Screen, press the § / BROWSE button to open the
BROWSE
screen.
NOTE
For more information about the
BROWSE
screen, see Chapter 6
“Working with Files and Folders (BROWSE screen)” on page 57.
2. Select the file that you want to add to the playlist and press the Á button to open the following pop-up menu.
For more information about selecting files, see “BROWSE screen navigation” on page 57.
3. Select
ADD LIST
, and press the Á button to add that file to the playlist. The pop-up menu closes.
4. Repeat steps 2 and 3 as necessary.
Numbers are assigned to the files in the order that they are added to the list.
Editing the playlist
You can view the playlist you have made on the
PLAYLIST
Screen. On this screen, you can also play files and edit the playlist
1. Press the MENU button to open the
MENU
screen.
2. Use the § / BROWSE and ¶/MIC buttons to select the
PLAYLIST
menu item, and press the Á button to open the
PLAYLIST
screen.
TASCAM LR-10
67
8–Playback Area and Playlist
For this operation, it does not matter which track you select in step 3. All the files are removed from the playlist, but they are not erased from the SD card.
3. Use the § / BROWSE and ¶/MIC buttons to select the file that you want to edit, and press the Á button to open the pop-up menu.
4. Use the § / BROWSE and ¶/MIC buttons to select the desired item, and press the Á button to execute the operation.
PLAY
Play the file and return to the Home Screen.
ALL CLR
A confirmation message appears to confirm that you want to remove all the files from the playlist. Press the Á button to remove all the files or the [ª] button to cancel this operation.
DELETE
Remove the selected track from the playlist.
The file is removed from the playlist, but it is not erased from the SD card.
CAUTION
No confirmation pop-up message appears before this operation.
68
TASCAM LR-10
MOVE
Select this to change the order of files in the playlist.
In addition to the file name, the file number also appears light on dark.
1. Use the § / BROWSE and ¶/MIC buttons to move the file to a different position in the playlist.
8–Playback Area and Playlist
CANCEL
No operation is conducted on the selected file, and the pop-up menu closes.
In the above example, the file in the 4th position has been moved to the 3rd position.
2. Press the Á button to complete the movement and return to the ordinary
PLAYLIST
screen. (The file number no longer appears light on dark.)
TASCAM LR-10
69
9–Special Playback (playback control function)
Using this unit’s playback control functions, you can change the speed of playback without changing the pitch and vice versa. You can use these playback control functions for effective practice and learning new parts.
Changing the speed
You can use the SPEED function to set the playback speed.
This unit has a Variable Speed Audition (VSA) function, so even when playback speed is changed the pitch stays the same.
Press the SPEED button to show the SPEED setting area at the bottom of the Home Screen.
Changing the key
You can use the KEY function to change the pitch of playback in semitone intervals (and the FINE TUNE function to change it in cents) without changing the speed.
Press the KEY button to show the
KEY
setting area at the bottom of the Home Screen on the display. Press the KEY button again to show the
FINE TUNE
setting area.
Use the VALUE (+/–) buttons to set the playback speed.
The speed can be set in a range between 50% ( x0.5
) and
150% ( x1.5
) of the original speed in 10% increments (default value: x1.0
).
When the
SPEED
is set from x0.5–x0.9, the shown, and when it is set from x1.1–x1.5, the shown.
70
TASCAM LR-10
icon is
icon is
KEY can be set in a range of ±6 semitones (â6–ã6). (The default value is
0
.)
If you change the key to any value besides 0, the key change function turns ON and the KEY icon (
)
appears on the
Home Screen as light letters on a dark background.
9–Special Playback (playback control function)
Use the
FINE TUNE
function to adjust the pitch by small amounts.
Set the amount of time to go back using the
FLASH
item.
1. Press the MENU button to open the
MENU
screen.
2. Use the § / BROWSE and ¶/MIC buttons to select the
PLAY MODE
menu item.
3. Press the Á button or ¯ button to open the
PLAY
MODE
screen.
4. Use the § / BROWSE and ¶/MIC buttons to select
FLASH
(setting value appears light on dark).
Use this to adjust the pitch up or down in cents (100 cents = 1 semitone) in a range of ±50. (The default value is
0
.)
NOTE
Even if you use the FINE TUNE function to adjust the key, as long as the KEY item setting is 0, the icon will not appear as light letters on a dark background on the Home Screen.
5. Use the VALUE (+/–) buttons to set the flashback time in a range from 1–10 seconds, in one-second intervals.
(Default value:
2
seconds)
6. After completing the setting, press the HOME button to return to the Home Screen.
Jump back a set amount and continue playback (flashback)
During playback, press the Á button to use the flashback function. This jumps back a few seconds and continues playback.
TASCAM LR-10
71
10–Loop Playback/Repeat Playback/Single Track Playback
In ordinary playback mode, unless you do something to stop it, once playback starts, it will stop only when the end of the last file in the current playback area is reached. By making the settings and conducting the operations described in this chapter, however, you can also make the unit loop a section of a file that you choose, repeat all the files in the current playback area, play a single track repeatedly or play a single track once and stop.
NOTE
A ccurate assignment of IN (starting) and OUT (ending) points is not always possible for variable bit rate (VBR) MP3 files.
The current position is set as the OUT (ending) point, and loop playback between the IN (starting) and OUT (ending) points begins.
• The current positions of the IN (starting) and OUT (ending) points are shown by the and icons that appear below the playback position display bar on the Home Screen.
•
During loop playback the icon also appears.
To stop loop playback, press the clears the loop interval setting.
LOOP button. This also
3. Press and hold the LOOP button to open the
LOOP SET pop-up.
Using loop playback (standard mode)
Use this function to continuously repeat playback (loop) part of a file that you select.
1. During playback (or when paused), press the LOOP button to set the point where you want to start loop playback.
The current position is set as the IN (starting) point.
2. Press the LOOP button at the point when you want loop playback to stop.
4. Use the Á, Ô, and [ª] buttons to move the
IN (starting) point to the desired position. Press the
 button to save the IN (starting) point.
72
TASCAM LR-10
10–Loop Playback/Repeat Playback/Single Track Playback
•
NOTE
When the
LOOP SET
pop-up window is open, press the Á button to playback, press [ª]button to, and press the
Ô or button briefly to search the file.
•
•
Press and hold the Ô or button to move the IN
(starting) or OUT (ending) point. (This is not possible when there is no IN (starting) and OUT (ending) point.)
Press the [ª] button during playback to pause, and press the HOME button when paused to returned to the
Home Screen.
5. Next, use the same buttons to move the OUT (ending) point to the desired position, and press the ¯ button to save the OUT (ending) point.
•
NOTE
Use the  and ¯ buttons to switch between IN
(starting) and OUT (ending) points.
6. Press the LOOP button briefly to start loop playback.
Using loop playback with the playlist
When the playback area is set to playlist, up to 5 loops with distinct IN (starting) and OUT (ending) points can be set per file.
Follow the procedures below to set and play back loops of desired intervals in a file.
Loop settings for a file are saved until it is removed from the playlist.
1. Press the LOOP button to show the LOOP setting area at the bottom of the display. The word
LOOP
is followed by a number. Use the VALUE (+/–) buttons to set the number to
1
–
5
.
TASCAM LR-10
73
10–Loop Playback/Repeat Playback/Single Track Playback
2. Press and hold the LOOP button to open the
LOOP SET pop-up.
• Press the [ª] button during playback to pause, and press the HOME button when paused to returned to the
Home Screen.
4. Next, use the same buttons to move the OUT (ending) point to the desired position, and press the ¯ button to save the OUT (ending) point.
3. Use the Á, Ô, and [ª] buttons to move the
IN (starting) point to the desired position. Press the
 button to save the IN (starting) point.
•
NOTE
When the
LOOP SET
pop-up window is open, press the Á button to playback, press [ª]button to, and press the
Ô or button briefly to search the file.
• Press and hold the Ô or button to move the IN
(starting) or OUT (ending) point. (This is not possible when there is no IN (starting) and OUT (ending) point.)
NOTE
Use the  and ¯ buttons to switch between IN
(starting) and OUT (ending) points.
5. Press the LOOP button briefly to start loop playback.
Turning loop playback on and off
Press the LOOP button briefly to turn loop playback ON or
OFF.
74
TASCAM LR-10
10–Loop Playback/Repeat Playback/Single Track Playback
When you want to restart loop playback, press the LOOP button briefly to start loop playback of the last used loop.
In the LOOP setting area shown at the bottom of the display, the word
LOOP
is followed by a number, which shows the current loop. Use the VALUE (+/–) buttons to change the loop number. During loop playback, you can change this number to start loop playback of a different loop if the loop assigned to that number has IN (starting) and OUT (ending) points set.
Repeat and single track playback
You can repeatedly play back the current file (one file) or multiple files within the designated playback area. You can also play just one file.
1. Press the MENU button to open the
MENU
screen.
2. Use the §/BROWSE and ¶/MIC buttons to select
PLAY
MODE
and press the Á button or ¯ button.
3. Use the §/BROWSE and ¶/MIC buttons to select the
REPEAT
item, and use the VALUE (+/–) buttons to set the playback mode.
OFF (default)
Play all tracks in the playback area in sequence. (This is the ordinary playback mode.)
SINGLE
Play one file without repeating.
The icon appears on the Home Screen.
1 REPEAT
Play the currently playing file repeatedly.
The icon appears on the Home Screen.
ALL REPEAT
Play all the files in the selected playback area repeatedly.
The icon appears on the Home Screen.
NOTE
If you start loop playback, the
REPEAT
item automatically switches to
OFF
if it is in a different mode.
TASCAM LR-10
75
11
–
Transferring songs to and from a computer
You can transfer audio files from a computer by USB, and play them back for practice, to learn new parts and to overdub.
Moreover, this unit can play back MP3 (32–320 kbps, 44.1 kHz) and WAV (44.1 kHz, 16/24-bit) audio file formats.
NOTE
Instead of using USB to connect this unit and a computer, you can also conduct the same operations by removing the SD card from this unit and connecting it directly to a computer that has a built-in SD card slot or by using a card reader.
Copying audio files from a computer
1. Connect the unit to the computer. (See “Connecting with a computer” on page 46.)
2. Click the LR-10 drive that appears on the computer to
open it, revealing UTILITY and MUSIC folders.
3. Drag-and-drop the desired audio files from the
computer to the MUSIC folder to copy those files to the
SD card.
Preparing audio files on a computer
Use the abilities of your computer OS or a software application to copy music files from a CD or other source to your computer.
When copying files to your computer, choose file types that this unit can handle (the MP3 and WAV files types listed above).
76
TASCAM LR-10
11–Transferring songs to and from a computer
4. After you finish copying files and closing the connection with the unit SD card from the computer, disconnect the USB cable. (Please refer to the operation manual for your computer system for instructions about the correct procedures for dismounting an external drive.)
The unit will automatically turns off.
TIP
You can also manage the contents of the MUSIC folder on an
SD Card from a computer.
You can create up two levels of sub-folders inside the MUSIC folder. Since you can set the unit to only play the contents of a specific folder, you can conveniently organize tracks into musical categories and artists. (See “Folder operations” on page 59.)
Name the sub-folders and music files as you like, and these names will appear on the unit’s display.
Transferring audio files to a computer
1. Click the LR-10 drive that appears on the computer to
open it, revealing UTILITY and MUSIC folders.
2. Open the MUSIC folder, and drag and drop the files that you want to copy to the desired location on the computer.
TASCAM LR-10
77
12–Using the built-in effects
This unit has built-in effects that can be applied to the input signal during both practice and recording.
Turning the effects ON and OFF
Press the EFFECT button briefly to turn the effects ON or OFF.
When ON, the effect last set on the
EFFECT
Screen becomes active, and the FX icon ( dark background.
) appears as light letters on a
Setting the effect
Press and hold the EFFECT button to open the
EFFECT screen.
Use the Â/¯ buttons to select the desired item. (When selected, the setting value appears as light letters on a dark background.) Use the VALUE (+/–) buttons to change the setting value.
REVERB
Select the type of reverb to use.
LEVEL knob
Use the REVERB item to adjust the output level of the selected reverb type.
TIME knob
Use the
PRESET
item to adjust the reverb time of the selected reverb type. The reverb time range is set optimally for each type of reverb. For this reason, the length of the reverb might differ between reverb types even with the same setting value.
SOURCE
Use this to set whether the effect is applied to the input signal
(
INPUT
) or the playback signal (
PLAY
).
The default setting is
PLAY
.
78
TASCAM LR-10
Reverb List
Reverb type
HALL 1
HALL 2
ROOM
STUDIO
PLATE 1
PLATE 2
Effects
This is a bright reverb modeled after a large halllike space.
This is a warm reverb modeled after a large halllike space.
This reverb is modeled on a small indoor space.
This reverb is modeled on a studio-like space
This is a bright plate reverb.
This is a warm plate reverb.
12–Using the built-in effects
TASCAM LR-10
79
13–Using the tuner
This unit has a built-in tuner. By inputting the sound of an instrument, you can use the tuning meter on the display to tune that instrument accurately. In addition, you can output a tone for tuning from the built-in speaker or the /LINE OUT jack, which is convenient for tuning multiple instruments simultaneously, for example.
3. The first item shown for each mode is
CALIB
. Use this to set the frequency of A between 435 Hz and 445 Hz.
Preparation
1. Press the TUNER button to open the TUNER screen.
2. The
MODE
item is shown. Use the [ª] button and
Á button to select the tuner mode. The options are
AUTO ( [ª] : chromatic tuner mode) and OSC. (Á : oscillator mode).
After selecting the mode, press the TUNER button again to make settings for that mode.
The setting value is shown on the right side of the screen.
This setting is the same for both tuner modes.
Use of each tuner mode is explained below.
NOTE
The signal input through the left MIC/LINE input channel is used for tuning. When using the built-in microphones to tune acoustic guitars and other instruments that have rapid sound decay, in particular, tune the instrument as close to the left built-in microphone as possible.
80
TASCAM LR-10
Chromatic tuner mode (AUTO)
This is the default mode. Watch the tuning meter on the unit’s screen as you tune your instrument.
AUTO
appears in the upper right. The tuning meter and input signal pitch name appear on the screen. (
---
appears when there is no input).
1. Input the signal of the instrument that you want to tune. The name of the closest pitch appears in the upper part of the meter.
2. Tune the instrument until the desired pitch is shown and the center of the meter is highlighted.
A bar appears to the left if the tuning is too low and a bar appears to the right if it is too high. The longer the bar is the more out of tune the instrument is.
Oscillator mode
13–Using the tuner
The built-in oscillator can output a tone for tuning through the built-in speaker or the /LINE OUT jack. The tuning pitch can be set in a three-octave range (C3–B5).
OSC.
appears in the upper right.
In addition to the
CALIB
item described above, the oscillator mode has the three other setting items that follow. Press the
TUNER button to cycle through the setting items.
OSC NOTE
Set the pitch of the tuning tone (C3–B5).
OSC LEVEL
Set the output level of the tone between 0 and 10 (default value 7).
TASCAM LR-10
81
14–Using the Metronome
This unit has a metronome function that is convenient for practicing an instrument.
LEVEL
Set the metronome volume between
0
and
10
. The default value is
5
.
Setting the metronome
1. Press the METRONOME button to open the
METRONOME screen.
Starting and stopping the metronome
When the
METRONOME
screen is open, press the Á button to start or stop the metronome.
NOTE
When the
METRONOME
screen is open, press the HOME button to stop the metronome and return to the Home Screen.
Set the following items on this screen.
Press the METRONOME button again to change the item.
Use the VALUE (+/–) buttons to change the setting value.
TEMPO
Set the speed to a value between
20
and
250
beats per minute (BPM). The default value is
120
.
BEAT
Set the accent frequency between
0
and
9
. There is no accent when set to
0
. The default value is
4
.
82
TASCAM LR-10
System settings (SETUP)
On the
SETUP
Screen, you can change various settings according to your use environment and other requirements.
You can also initialize and format the SD card.
To access the
SETUP
screen, press the MENU button to open the menu list, select the
SETUP
item using the §/BROWSE and ¶/MIC buttons and press the Á button or ¯ button.
You can make the following settings on the
SETUP
screen.
Use the §
/ BROWSE and ¶/MIC buttons to select the desired item. (When selected, the “:” becomes “∑” and the setting value appears as light letters on a dark background.) Use the
VALUE (+/–) buttons to change the setting value.
15–System settings
Setting the forward/backward search speed
Use the
CUE/REV SPEED
item to set the speed of forward/ backward searching when pressing and holding the
Ô / button during audio file playback.
Options: x2
, x4
, x8
(Default value), x10
Setting the automatic power off time
Use the
AUTO OFF
item to set the time before the unit power automatically turns OFF after the last activity or operation when powered by the internal battery.
Options:
OFF
(Default value),
3min
,
5min
,
10min
,
30min
Adjusting the display contrast
Use the
CONTRAST
item to adjust the display contrast.
Range:
1
–
20
(Default value:
5
)
Setting the battery type
Use the
BATTERY TYPE
item to set the kind of batteries used in the unit. This setting is used to show the amount of remaining battery charge and to determine if the unit has enough power for normal operation.
Options:
ALKAL
(alkaline batteries, default value),
Ni-MH
(nickel-metal hydride batteries)
TASCAM LR-10
83
15–System settings
Restoring the default values (factory settings)
Use the
INITIALIZE
item to restore the various settings of this unit to their factory default values.
1. Use the §/BROWSE and ¶/MIC buttons to select
INITIALIZE
(
Exec
appears light on dark).
2. Press the Á button to open a confirmation pop-up window.
2. Press the Á button to open a confirmation pop-up window.
3. Press the Á button to initialize the settings.
Press the [ª] button to cancel initialization.
Using QUICK FORMAT
Use the
QUICK FORMAT
item to format an SD card quickly.
Using the
QUICK FORMAT
item deletes all music files on the card, and automatically creates MUSIC and UTILITY folders and a dr-1.sys file.
1. Use the §/BROWSE and ¶/MIC buttons to select the
QUICK FORMAT
item (
Exec
appears light on dark).
84
TASCAM LR-10
3. Press the Á button to execute quick formatting.
Press the [ª] button to cancel quick formatting.
Using FULL FORMAT
Use the
FULL FORMAT
item to completely format an SD card.
Using the
FULL FORMAT
item deletes all music files on the card, and automatically creates MUSIC and UTILITY folders and a dr-1.sys file.
If you use the
FULL FORMAT
item, the unit checks the memory for errors before formatting the card. For this reason it takes a long time compared to the
QUICK FORMAT
option.
1. Use the §/BROWSE and ¶/MIC buttons to select
FULL
FORMAT
(
Exec
appears light on dark).
15–System settings
2. Press the Á button to open a confirmation pop-up window.
3. Press the Á button to execute full formatting.
Press the [ª] button to cancel full formatting.
CAUTION
When formatting a card, use a TASCAM PS-P520 AC adapter
(sold separately), USB bus power or confirm that the batteries are sufficiently charged. If the power fails during formatting, the formatting might not occur correctly.
Setting the file name format
You can set the format of the names given to files recorded by the unit.
1. Press the MENU button to open the
MENU
screen.
2. Use the § / BROWSE and ¶/MIC buttons to select the
FILE NAME
menu item, and press the Á button or ¯ button to open the
FILE NAME
screen.
Use the §/BROWSE and ¶/MIC buttons to select each item,
(when selected, the “
:
” becomes an “∑” and the setting value is highlighted or the cursor is shown.
You can make the following settings for the items on the screen.
File name format
Use the VALUE (+/–) buttons to set the
TYPE
item to
WORD
or
DATE
.
Options:
WORD
( default value),
DATE
WORD
: The six characters set in the
WORD
item are used to name files.
Example: LR0000_0000.wav
DATE
: The date is used to name files (yymmdd).
Example: 090101_0000.wav
NOTE
The date is set according to the unit’s internal clock. (See
“Setting the date and time” on page 45.)
TASCAM LR-10
85
15–System settings
Setting the characters in the WORD item
When the
WORD
item is selected, use the  and ¯ buttons to move the cursor, and use the VALUE(+/–) buttons to change each character.
NOTE
In addition to the alphabet and numbers, the following characters can be used: ! # $ % & ’ ( ) + , - . ; = @ [ ] ^ _ ` { } ~
The default name prefix is “
LR0000
”.
86
TASCAM LR-10
This unit has a REMOTE jack to which you can connect a TASCAM RC-3F footswitch-type remote control (sold separately) that can be used to operate the unit.
Setting footswitch operation
Use the
FOOT SW
setting screen to make footswitch settings.
1. Press the MENU button to open the
MENU
screen.
2. Use the § / BROWSE and ¶/MIC buttons to select the
FOOT SW
menu item, and press the Á button or ¯ button to open the
FOOT SW
screen.
16–Using the footswitch
4. Use the VALUE (+/–) buttons to change the
MODE
item.
MODE
PLAY
TRAINER
RECORD OVERDUB REC/PAUSE
MINUTES
L
REW
FLASH
REW
FOOT SW
C
PLAY/STOP
PLAY/STOP
PLAY
R
FWD
SPEED CHANGE
STOP
FWD
5. After completing the setting, press the HOME button to return to the Home Screen.
Using the footswitch
Press a pedal on the footswitch to operate the unit. The function of each pedal corresponds to the assignment shown on the
FOOT SW
screen.
3. The
MODE
item and the three footswitch pedal assignments are shown.
TASCAM LR-10
87
17–Viewing File Information
Use the
INFORMATION
Screen to view various types of information about the unit.
To open the
INFORMATION
screen, press the MENU button to open the
MENU
screen, select the
INFORMATION
item and press the Á button or ¯ button.
The
INFORMATION
screen has the following three pages.
Use the VALUE (+/–) buttons to switch between the pages.
• File information page (
FILE
)
•
Shows information about the currently playing file.
Card information page (
CARD
)
•
Shows the use status of the currently inserted SD card.
System information page (
SYSTEM
)
Shows information about the unit’s system settings and firmware version.
When you are done, press the HOME button to return to the
Home Screen, or press the MENU button to open the
MENU screen.
File information page
The
FILE
page shows information about the currently playing file.
WAV or MP3
Shows the audio file format.
For WAV files, bit length, stereo/mono and sampling frequency (Hz) are shown.
For MP3 files, bit rate (kbps), CBR (constant bit rate) or VBR
(variable bit rate) type and sampling frequency (Hz) are shown.
TITLE
Shows the file name.
If an MP3 file has ID3 tag title information that information appears instead.
DATE
Shows the date and time that the file was created.
88
TASCAM LR-10
SIZE
Shows the file size.
Card information page
The CARD page shows the use status of the currently inserted
SD card.
TOTAL MUSIC
Shows the number of playable files in the MUSIC Folder.
TOTAL FOLDER
Shows the number of folders in the MUSIC Folder.
TOTAL SIZE
Shows the total SD card memory capacity.
REMAIN SIZE
Shows the amount of unused memory on the SD card.
USED SIZE
Shows the amount of used memory on the SD card.
17–Viewing File Information
NOTE
Use the ¯ button to switch between display of
REMAIN
SIZE
and
USED SIZE
.
TASCAM LR-10
89
17–Viewing File Information
System information page
The
SYSTEM
page shows information about the unit’s system settings and firmware version.
CUE/REV SPD
Shows the speed of forward and backward searching.
AUTO OFF
Shows the automatic power OFF setting.
BATTERY
This shows the battery setting.
System Ver.
Shows the system firmware version.
90
TASCAM LR-10
18–Messages
The following is a list of the popup messages that might appear on the LR-10 under certain conditions. Refer to this list if one of these popup messages appears and you want to check the meaning or determine a proper response.
Message
File Name ERR
Meaning and response
The DIVIDE function would cause the file name to exceed 200 characters. The DIVIDE function adds "_a” or “_b” to the end of the file name. Before choosing the DIVIDE function, connect the unit to a computer and edit the file name to less than 198 characters.
Dup File Name
File Not Found
Non-Supported
Battery Empty
I/O Too Short
File Not Found
PLAYLIST
The DIVIDE function would cause the file name to be the same as that of an existing file. The DIVIDE function adds "_a” or “_b” to the end of the file name. Before choosing the DIVIDE function, connect the unit to a computer and edit the file name.
The file added to the playlist cannot be found or a file could be damaged. Please check the file in question.
The audio file is not a supported format. Please see "11-Transferring songs to and from a computer" for file formats that this unit can use.
The battery is almost out of power. Replace the AA batteries.
The IN (starting) and OUT (ending) points are too close together. Reset the IN (starting) and OUT (ending) points with at least 1 second between them.
The file in the Playlist cannot be found. Please confirm that the file is still in the Music Folder.
No PLAYLIST
PLAYLIST Full
MBR Error Init
CARD
No files have been added to the Playlist. Add a file to the Playlist or change the play mode to something besides PLAYLIST.
The playlist is full. You cannot add more than 99 tracks to the Playlist.
The card is not formatted properly or the formatting is broken. Change the card or press the Á button when this message appears to format the card in FAT format.
CAUTION: Execution of FAT formatting erases all data currently on the card.
TASCAM LR-10
91
18–Messages
Message
Format Error
Format CARD
File Not Found
Make Sys File
Invalid Sys File
Make Sys File
Invalid Card
Change Card
Protected Card
Change Card
Write Timeout
Card Full
Layer too Deep
Can't Divide
Max File Size
File Full
Card Error
Current File MP3
92
TASCAM LR-10
Meaning and response
The FAT formatting of the card is abnormal or broken. This message also appears if you FAT formatted the card using a computer connected by USB and if a new card is inserted in the unit. Always use the LR-10 to conduct
FAT formatting of cards to be used with it. Change the card or press the Á button when this message appears to format the card in FAT format.
CAUTION: Execution of FAT formatting erases all data currently on the card.
The system file is missing. This unit requires a system file for operation. When this message appears, press Á button to automatically create a system file.
The system file required to operate this unit is invalid. When this message appears, press Á button to automatically create a system file.
Something might be wrong with the card. Change the card.
This appears when the card is protected and lacks the necessary Music Folder and other folders and files. Unlock the write protect switch, restart the power and format the card.
Writing to the card timed out.
Backup files on the card to your computer, and format the card.
The card has no remaining capacity. Erase unnecessary files or move them to your computer to make open space.
Folders can be created down to two layers. You cannot create a new folder inside the current folder.
The position selected for divide is not suitable (too close to the beginning or end of a track).
The file is larger than the designated size or the recording time exceeded 24 hours.
The total number of folders and files exceeds 5000. Erase unnecessary files or move them to your computer.
The card could not be handled properly. Replace the card.
MP3 files cannot be divided.
18–Messages
Message
File Protected
No Card
No PB File
No MUSIC File
Not Continued
File Error
Can't Save Data
Player Error
Device Error
Writing Failed
Sys Rom Err
Remote Cmd
Remote Rx
System Err 50
System Error 1
System Error 2
System Error 3
System Error 4
The file is read only and cannot be erased.
Meaning and response
No card is in the unit, so recording is not possible.
There is no file that can be played back. The file might be damaged.
There is no playback file, so DIVIDE and OVERDUB cannot be executed.
If any of these errors occur, turn the unit power OFF and restart it. If the power cannot be turned OFF, remove the batteries and disconnect the AC adaptor (if connected). If the error message continues to appear, please contact a TEAC Repair Center.
TASCAM LR-10
93
18–Messages
Message
System Error 5
System Error 6
System Error 7
System Error 8
System Error 9
Meaning and response
If any of these errors occur, turn the unit power OFF and restart it. If the power cannot be turned OFF, remove the batteries and disconnect the AC adaptor (if connected). If the error message continues to appear, please contact a TEAC Repair Center.
94
TASCAM LR-10
If you are having trouble with the operation of this unit, please try the following before seeking repair. If these measures do not solve the problem, please contact the store where you bought the unit or a TASCAM Service Center.
ª Power will not turn ON.
• Confirm that the batteries are not dead.
• Confirm that the batteries are installed with the correct +/– orientation.
• Confirm that the power plug of the AC adaptor (TASCAM
PS-P520: sold separately) is securely inserted.
ª The foot switch does not function.
• Confirm that a battery is installed in the foot switch and that it is not dead.
ª The unit does not function.
• Is the unit connected to a computer by USB (
USB connected
) ?.
ª
•
The SD card is not recognized.
Confirm that the SD card is inserted completely.
19–Troubleshooting
ª Playback does not work.
• If you are trying to play a WAV file, confirm that the sampling frequency is supported by this unit.
• If you are trying to play an MP3 file, confirm that the bit rate is supported by this unit.
ª No sound is output.
• Are headphones connected?
• Check the connections with the monitoring system.
• Is the volume of the monitoring system minimized?
• Is the OUTPUT setting of the unit minimized?
•
•
•
•
•
ª Recording does not work.
• If you are using an external device, check the connection again.
Check the input settings again.
Confirm that the recording level is not too low.
Has MIC/LINE input been disabled ( MIC or LINE icon ( or )not shown light on dark)?
Confirm that the SD card is not full.
Confirm that the number of files has not reached the maximum that the unit can handle.
TASCAM LR-10
95
19–Troubleshooting
ª The recording level is low.
• Confirm that the input level setting is not too low.
• Confirm that the
GAIN
setting is not too low.
• Confirm that the output level of a connected external device is not too low.
ª The sound I am trying to record sounds distorted.
• Is the
INPUT LEVEL high?
setting low and the input gain setting
ª The playback sounds unnatural.
• Confirm that the playback pitch is not being adjusted.
• Confirm that the playback speed is not being adjusted.
ª I cannot erase a file.
• Is the SD card write-protect switch engaged?
•
•
ª This unit’s files do not appear on the computer.
• Confirm that the unit is connected to the computer using its USB port.
Are you using a USB hub?
Confirm that the unit is not recording or in recording standby mode.
96
TASCAM LR-10
Ratings
Recording media
SD card (64 MB - 2 GB)
SDHC card (4 GB - 32 GB)
Recording format
WAV: 44.1kHz, 16-bit
Playback format
WAV: 44.1 kHz, 16/24-bit
MP3: 44.1/48 kHz, 32/64/96/128/192/256/320 kbps
Number of input channels
2 channels (stereo)
Input ratings
Analog audio input
LINE IN jack
Connector : 1/8” (3.5 mm) stereo
Input impedance : 23 kΩ
Nominal input level : –10 dBV (0.32V) , (INPUT volume at 7)
20–Specifications
Maximum input level : +6 dBV (2.0 V) , (INPUT volume at 7)
Minimum input level : –22 dBV (0.08 V) , (INPUT volume at 10)
Built-in microphone
Omni directional, Stereo
Output ratings
Analog output ratings
/LINE OUT
Connector : 1/8” (3.5 mm) stereo mini
Output impedance : 23Ω
Nominal output level : –14 dBV (10 kΩ load)
Maximum output level : +2 dBV (10 kΩ load)
Maximum output : 15 mW + 15 mW (32Ω load)
Built-in speaker
0.4 W (monaural)
Control input/output ratings
USB jack
Connector : Mini-B type
Format : USB 2.0 HIGH SPEED, mass storage class
TASCAM LR-10
97
20–Specifications
REMOTE jack
Connector : 2.5mm TRS
Audio performance
Frequency response
20 Hz - 20 kHz +1/–3 dB
(LINE IN to LINE OUT , Fs=44.1 kHz)
Total harmonic distortion
0.03% (LINE IN to LINE OUT, Fs=44.1 kHz)
S/N ratio
90 dB (LINE IN to LINE OUT, Fs=44.1 kHz)
Computer compatibility
Windows
Pentium 300 MHz or faster
128 MB or more memory
USB port (USB 2.0 recommended)
Macintosh
Power PC, iMac, G3, G4 266 MHz or faster
98
TASCAM LR-10
64 MB or more memory
USB port (USB 2.0 recommended)
Recommended USB host controller
Intel chipset
Supported OS
Windows : Windows XP , Windows Vista , Windows 7
Macintosh : Mac OS X 10.2 or later
Other specifications
Power
Two AA batteries (Alkaline or Ni-MH)
AC adaptor (TASCAM PS-P520, sold separately)
USB bus power
Power consumption
0.4 W (during MP3 playback)
Battery operation time (continuous operation)
Alkaline type battery ( EVOLTA )
About 13 hours (WAV, recording time when using the builtin microphones input)
20–Specifications
About 13 hours (WAV, MP3, music playback time when using headphones)
About 8 hours (WAV, MP3, music playback time when using the built-in speaker)
Ni-MH type battery ( eneloop )
About 11 hours (WAV, recording time when using the builtin microphones input)
About 11 hours (WAV, MP3, music playback time when using headphones)
About 7.5 hours (WAV, MP3, music playback time when using the built-in speaker)
Dimensions (W x H x D)
158 x 30 x 70 mm
6.220 x 1.181 x 2.756 in.
Weight
170 g /5.996 oz (not including batteries)
Operating temperature range
0 - 40°C/32°F - 104°F
Dimensional drawings
158 mm 30 mm
•
•
Illustrations and other depictions may differ in part from the actual product.
Specifications and external appearance may be changed without notification to improve the product.
TASCAM LR-10
99
LR-10
TEAC CORPORATION
Phone: +81-42-356-9143
1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan
TEAC AMERICA, INC.
Phone: +1-323-726-0303
7733 Telegraph Road, Montebello, California 90640 USA
TEAC CANADA LTD.
Phone: +1905-890-8008 Facsimile: +1905-890-9888
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada
TEAC MEXICO, S.A. de C.V.
Phone: +52-55-5010-6000
Río Churubusco 364, Colonia Del Carmen, Delegación Coyoacán, CP 04100, México DF, México
TEAC UK LIMITED
Phone: +44-8451-302511
Suites 19 & 20, Building 6, Croxley Green Business Park, Hatters Lane, Watford, Hertfordshire. WD18 8TE, U.K.
TEAC EUROPE GmbH
Phone: +49-611-71580
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany www.tascam.jp
www.tascam.com
www.tascam.com
www.teacmexico.net
www.tascam.co.uk
www.tascam.de
Printed in China
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 10 Step 1: Prepare the SD card and power
- 12 Step 2: Copy audio files from a computer
- 12 Step 3: Select the input
- 13 Step 4: Connect an instrument and headphones
- 13 Step 5: Tune the instrument
- 14 Step 6: Use the effects
- 14 Step 7: Adjust the input and output levels
- 15 Step 8: Play along with the music
- 17 Step 9: Record your performance
- 17 Step 10: Record over a song (overdub)
- 18 Step 11: Use other functions
- 18 Step 12: Turn off the power
- 19 Main functions and features
- 20 Included items
- 20 About this manual
- 21 Intellectual property rights
- 22 About SD cards
- 22 Precautions for use
- 23 Precautions for placement and use
- 23 Beware of condensation
- 23 Cleaning the unit
- 24 Top panel
- 30 Left side panel
- 30 Right side panel
- 31 Rear panel
- 31 Front panel
- 32 Bottom panel
- 33 Home Screen
- 35 Recording screen
- 36 Menu structure
- 37 Using the menu
- 38 Basic operations
- 39 Inserting and removing SD cards
- 39 Inserting an SD card
- 40 Removing an SD card
- 40 Preparing an SD card for use
- 41 Special cases
- 41 Card write protection
- 42 Powering the unit
- 42 Using AA batteries
- 42 Using USB bus power
- 43 Using an AC adaptor (sold separately)
- 44 Startup and shutdown
- 44 Turning the power on
- 44 Setting the power to standby
- 45 Setting the date and time
- 46 Connecting monitoring equipment
- 46 Connecting with a computer
- 47 Disconnecting from a computer
- 47 Connecting an instrument
- 48 Setting the location where recorded files are saved
- 48 Setting the input functions
- 49 Adjusting the input level
- 50 Recording
- 51 Recording a few seconds before pushing the record button (pre-recording)
- 51 Recording the input sound with the playback sound (overdubbing)
- 52 Overdubbing
- 53 Starting and pausing recording automatically (AUTO REC)
- 54 Track incrementation
- 54 Manual track incrementation during recording
- 55 Automatic track incrementation by file size
- 55 Dividing files (DIVIDE)
- 56 Recording duration
- 57 BROWSE screen navigation
- 57 Icons on the BROWSE screen
- 58 File operations
- 59 Folder operations
- 60 Delete the selected playback file (QUICK DELETE)
- 61 Playback
- 61 Stopping playback
- 61 Selecting a file
- 62 Searching forward and backward
- 62 Adjusting the playback volume
- 63 Adjusting the balance between playback and input signals
- 63 Disabling the MIC/LINE input
- 64 Using the PLAY MODE screen to set the playback area
- 65 Selecting a folder for the playback area (1)
- 66 Selecting a folder for the playback area (2)
- 67 Playlist
- 67 Adding files to the playlist
- 67 Editing the playlist
- 70 Changing the speed
- 70 Changing the key
- 71 Jump back a set amount and continue playback (flashback)
- 72 Using loop playback (standard mode)
- 73 Using loop playback with the playlist
- 74 Turning loop playback on and off
- 75 Repeat and single track playback
- 76 Preparing audio files on a computer
- 76 Copying audio files from a computer
- 77 Transferring audio files to a computer
- 78 Turning the effects ON and OFF
- 78 Setting the effect
- 79 Reverb List
- 80 Preparation
- 81 Chromatic tuner mode (AUTO)
- 81 Oscillator mode
- 82 Setting the metronome
- 82 Starting and stopping the metronome
- 83 System settings (SETUP)
- 83 Setting the forward/backward search speed
- 83 Setting the automatic power off time
- 83 Adjusting the display contrast
- 83 Setting the battery type
- 84 Restoring the default values (factory settings)
- 84 Using QUICK FORMAT
- 84 Using FULL FORMAT
- 85 Setting the file name format
- 85 File name format
- 86 Setting the characters in the WORD item
- 87 Setting footswitch operation
- 87 Using the footswitch
- 88 File information page
- 89 Card information page
- 90 System information page
- 97 Ratings
- 97 Input ratings
- 97 Analog audio input
- 97 Output ratings
- 97 Analog output ratings
- 97 Control input/output ratings
- 98 Audio performance
- 98 Computer compatibility
- 98 Other specifications
- 99 Dimensional drawings