Vdp200oaw8 GB
VDP200OAW8 – "BEAM TRACKER 200" ONE-ARMED MOVING WASH HEAD - 8 CHANNELS
1. Introduction & Features
To all residents of the European Union
Important environmental information about this product
This symbol on this unit or the package indicates that disposal of this unit after its lifecycle could harm the environment.
Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be brought to a specialized company for recycling.
This unit should be returned to your distributor or to a local recycling service.
Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for buying the VDP200OAW8! If it was damaged in transit, don't install or use it and contact your dealer.
The VDP200OAW8 should come with a power cable, an XLR connection cable and this manual.
Its features are:
• pan 540°/tilt 280°
• 11 dichroic colours + white
• colour wheel with rainbow effect in both directions
• strobe: 0 ~ 8Hz, pulse strobe or sound activity strobe
• automatic program and music control
• display: digital address and function setting
• high speed pan & tilt movements
• display can turn 180° if the mounting location so requires
• DMX mode, stand-alone mode or master-slave synchro mode
• soft edge output from 80mm PC lens, 20° beam aperture
• memory function: automatic pan/tilt position correction
• on-board programming, 3 programs of each 99 steps
• dimmer unit allowing very smooth micro-step driven dimming
2. Safety Instructions
Be very careful during the installation: touching live wires can cause life-threatening electroshocks.
Do not touch the device during operation as the housing heats up.
Keep this device away from rain and moisture.
Unplug the mains lead before opening the housing.
• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will
not accept responsibility for any ensuing defects or problems.
• A qualified technician should install and service this device.
• Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the device
against damage by leaving it switched off until it has reached room temperature.
• This device falls under protection class I. It is therefore essential that the device be earthed. Have a qualified
person carry out the electric connection.
• Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.
• Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary.
• Disconnect the device from the mains to clean it or when it is not in use. Handle the power cord by the plug only.
• There may be some smoke or a particular smell when the device is activated for the first time. This is normal and
any smoke or smell will gradually disappear.
VDP200OAW8
1
VELLEMAN
• Do not look directly at the light source as sensitive people may go into epileptic seizure if they do.
• Note that damage caused by user modifications to the device is not covered by the warranty.
• Keep the device away from children and unauthorised users.
3. General Guidelines
• This device is designed for professional use on stage, in discos, theatres, etc. The VDP200OAW8 should only be
used indoors with an alternating current of max. 230V AC/50Hz.
• Lighting effects are not designed for permanent operation: regular operation breaks will prolong their lives.
• Do not shake the device. Avoid brute force when installing or operating the device.
• Select a location where the device is protected against extreme heat (see “7. Technical Specifications”), dust and
moisture. Respect a minimum distance of 0.5m between the device’s light output and any illuminated surface.
• Use an appropriate safety cable to fix the device (e.g. VDLSC8).
• Familiarise yourself with the functions of the device before actually using it. Do not allow operation by unqualified
people. Any damage that may occur will most probably be due to unprofessional use of the device.
• Use the original packaging if the device is to be transported.
• All modifications of the device are forbidden for safety reasons.
• Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electroshocks, lamp
explosion, crash, etc. Using the device in an unauthorised way will void the warranty.
• ! Never look directly into the light source, as sensitive persons may suffer an epileptic shock.
4. Installation
a) Installing or replacing the lamp
•
•
•
•
•
Only fit or replace a lamp when the device is unplugged from the mains.
Let a lamp cool down before replacing it as the temperature of a lamp can reach 700°C during operation.
When handling a halogen lamp, do not touch it with your bare hands. Use a cloth to insert or remove it.
Do not install lamps with a higher wattage than that for which this device was designed.
Replace any deformed or damaged lamp with a lamp of the same type (see “7. Technical Specifications”):
For the installation, you need 70V / 150W CDM G12 lamp, order code LAMP150HTI/2
Please remember the lamp is not a hot-restrike type, you must wait for approximately 10 minutes after having turned
off the lamp before you can turn it back on again.
Remark: Do not operate the device when the lid is off.
b) Mounting the device
•
•
•
•
•
•
•
•
•
•
•
Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable norms.
The carrying construction must be able to support 10 times the weight of the device for 1 hour without deforming.
The installation must always be secured with a secondary attachment e.g. a safety cable.
Never stand directly below the device when it is being mounted, removed or serviced. Have a qualified technician
check the device once a year and once before you bring it into service.
Install the device in a location with few passers-by that is inaccessible to unauthorised persons
Overhead mounting requires extensive experience: calculating workload limits, determining the installation
material to be used. Have the material and the device itself checked regularly. Do not attempt to install the device
yourself if you lack these qualifications as improper installation may result in injuries.
Before mounting make sure the installation area can hold a minimum point load of 10 times the device's weight.
Make sure there is no flammable material within a 50cm radius of the device.
Have a qualified electrician carry out the electric connection.
Connect the device to the mains with the power plug. Do not connect it to a dimming pack.
The installation has to be approved by an expert before the device is taken into service.
VDP200OAW8
2
VELLEMAN
5. Use
The moving head can be controlled by up to 8 DMX channels:
CHANNEL 1: pan movement (max. 530°): 8 bit
CHANNEL 2: tilt movement (max. 285°): 8 bit
CHANNEL 3: pan movement fine: 16 bit
CHANNEL 4: tilt movement fine: 16 bit
CHANNEL 5: speed of pan and tilt movement
CHANNEL 6: colour selection
CHANNEL 7: dimmer
CHANNEL 8: strobe effect
a. Detailed DMX values per channel
CHANNEL 1
CHANNEL 2
CHANNEL 3
CHANNEL 4
Description
pan
tilt
pan fine
tilt fine
CHANNEL 5
pan / tilt speed
CHANNEL 6
colour wheel
CHANNEL 7
dimmer
CHANNEL 8
strobe
VDP200OAW8
From
0
0
0
0
0
To
255
255
255
255
249
250
255
0
10
21
32
42
53
64
74
85
96
106
117
129
191
193
0
0
32
64
96
128
160
192
224
9
20
31
41
52
63
73
84
95
105
116
128
190
192
255
255
31
63
95
127
159
191
223
255
3
Function
8 bit
8 bit
16 bit
16 bit
Speed setting (max > min)
max. speed, blackout while pan / tilt moving or
blackout while colour / gobo change
white
turquoise
red
cyan
green
magenta
blue
green
yellow
pink
dark blue
orange
colour rotation
music controlled colour changing
rainbow effect (slow > fast)
dimmer (0-100%) with CHANNEL 8 on 255
shutter closed
shutter open
strobe effect
shutter open
music controlled strobe effect
pulse strobe effect (close > open)
pulse strobe effect (open > close)
shutter
VELLEMAN
b. DMX-512 control connection
Connect the provided XLR cable to the female 3-pin XLR output of your
controller and the other side to the male 3-pin XLR input of the
VDP200OAW8. Multiple VDP200OAW8's can be linked through serial
linking. The linking cable should be two core, screened cable with XLR
input and output connectors. Please refer to the diagram on the right.
c. DMX-512 connection with DMX termination
A DMX terminator is recommended for installations where the DMX cable has to run a long
distance or is in an electrically noisy environment (e.g. discos). The terminator prevents
corruption of the digital control signal by electrical noise. The DMX terminator is simply an
XLR plug with a 120Ω resistor between pins 2 and 3, which is then plugged into the XLR
output socket of the last device in the chain.
Please see illustrations to the left.
d. Projector DMX start address selection
All DMX-controlled devices need a digital start address so that the correct device responds to the signals. This digital
start address is the channel number from which the device starts to “listen” to the DMX controller. Enter the correct
number and read it from the display located on the base of the VDP200OAW8.
You can use the same starting address for a whole group of devices or enter an individual one for every device.
When all devices have the same address, all the units will “listen” to the control signal on one particular channel. In
other words: changing the settings of one channel will affect all devices simultaneously. If you set different
addresses, each device will “listen” to a separate channel number. Changing the settings of one channel will only
affect the device in question.
In the case of the 8-channel VDP200OAW8, you will have to set the start address of the first unit to 1, the second
unit to 9 (8 + 1), the third to 17 (9 + 8), and so on.
e. Function selection
Different functions can be set by means of the 5 push buttons and the display. When you turn on the fixture the
display setting will be the same as the setting before you turned it off.
Procedure:
• press UP or DOWN button to select a different function
• press ENTER to confirm the selected function, the display will show "PASS"
• select it to be on or off using the NO or YES button (No= up and YES= down while in DMX start address
selection mode)
• press ENTER again to confirm your settings
• press EXIT/DN to save the setting and exit the menu
VDP200OAW8
4
VELLEMAN
Please refer to the list below for the different settings:
Channel
1
2
3
4
5
6
7
8
Function
F5
F6
F7
F8
F9
FA
FB
FC
F1
pan
tilt
pan (16 bit)
tilt (16 bit)
speed
colour
gobo
shutter
F2
pan
pan (16bit)
tilt (16 bit)
tilt (16 bit)
speed
colour
gobo
shutter
F3
pan
tilt
speed
colour
gobo
shutter
Corresponding function
N
N
N
N
N
N
N
N
pan
tilt
setup
music control
auto program
master – slave mode
no function
display up/down
F4
pan
tilt
colour
gobo
shutter
Y
Y
Y
Y
Y
Y
Y
Y
6. Cleaning and Maintenance
1. All screws should be tightened and free of corrosion.
2. The housing, the lenses, the mounting supports and the installation location (e.g. ceiling, suspension, trussing)
should not be deformed, modified or tampered with e.g. do not drill extra holes in mounting supports, do not
change the location of the connections …
3. Mechanically moving parts must not show any signs of wear and tear.
4. The electric power supply cables must not show any damage. Have a qualified technician maintain the device.
5. Disconnect the device from the mains prior to maintenance activities.
6. Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.
7. There are no user-serviceable parts, apart from the lamp (see “4. Installation”).
8. Contact your dealer for spare parts if necessary.
7. Technical Specifications
Power Supply
Power Consumption
Lamp
Dimensions
Total Weight
Max. ambient temperature
Max. housing temperature
max. 230Vac/50Hz
max. 300W
70V / 150W CDM G12 (ordercode: LAMP150HTI/2)
320 x 345 x 425mm
10.5kg
45°C
75°C
The information in this manual is subject to change without prior notice.
VDP200OAW8
5
VELLEMAN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising