Ceramic Tower Heater Item: NH-9015TR

Ceramic Tower Heater Item: NH-9015TR
Ceramic Tower Heater
Item: NH-9015TR
1
INSTRUCTION MANUAL
FOR HOUSEHOLD USE ONLY
Read all the instructions carefully before you use the appliance and keep the manual for future
use.
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to
reduce the risk of fire, electric shock, and injury to person(s), including the following:
READ AND SAVE THESE INSTRUCTIONS.
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL,
OPERATE OR MAINTAIN THE PRODUCTS DESCRIBED. PROTECT
YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION.
FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL
INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
Preparation before operating
1. Check if the electrical voltage of the main supply and the load of the socket
match the rated voltage and power marked on the rating label of the appliance.
2. Check if the socket and the plug are undamaged, and put the plug well in the
socket.
3. Put the appliance on a stable and flat surface to avoid risk of falling down.
4. Be sure that there is enough space for the ceramic heater while operating, at
least 50 cm around the appliance, and right before the air outlet, the distance
should be at least 120 cm.
Safety Precautions
1) Read all instructions before using this heater.
2) This heater is hot when in use. To avoid burns, do not let bare skin touch hot
surfaces. If provided, use handles when moving this heater. Keep combustible
materials, such as furniture, pillows, bedding, papers, clothes, and curtains at
least a _3_feet (a _0.9_ m) from the front of the heater and keep them away from
the sides and rear.
3) Extreme caution is necessary when any heater is used by or near children or
invalids and whenever the heater is left operating and unattended.
2
4) Always unplug heater when not in use.
5) Do not operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner. Discard heater, or
return to authorized service facility for examination and/or repair.
6) Do not use outdoors.
7) Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or
similar coverings. Do not route cord under furniture or appliances. Arrange cord
away from traffic area and where it will not be tripped over.
9) To disconnect heater, turn controls to off, then remove plug from outlet.
10) Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or fire, or damage the heater.
11) To prevent a possible fire, do not block air intakes or exhaust in any manner.
Do not use on soft surfaces, like a bed, where openings may become blocked.
12) A heater has hot and arcing or sparking parts inside. Do not use it in areas
where gasoline, paint, or flammable liquids are used or stored.
13) Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock, or injury to
persons.
14) Always plug heaters directly into a wall outlet/receptacle. Never use with an
extension cord or relocatable power tap (outlet/power strip).
15) This heater is not intended for use in bathrooms, laundry areas and similar indoor
locations. Never locate heater where it may fall into a bathtub or other water container.
WARNING: This product is equipped with a polarized plug (one blade is wider than the
other blade). To reduce the risk of electrical shock, this plug will fit into a polarized
outlet only one way. This is a safety feature. If you are unable to insert the plug into
the electrical outlet, try reversing the plug. If the plug still does not fit, contact a
qualified electrician. Avoid the use of an extension cord because the extension cord
may overheat and cause rise of fire. Always plug heaters directly into a wall
outlet/receptacle. Never use with an extension cord or relocatable power tap
(outlet/power strip).
WARNING: REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
-DO NOT USE THIS HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES.
WARNING: DO NOT DEPEND ON THE ON/OFF BUTTON AS THE SOLE MEANS OF
DISCONNECTING POWER WHEN SERVICING OF MOVING THE HEATER. ALWAYS
UNPLUG THE POWER CORD.
CAUTION: TO PREVENT ELECTRIC SHOCK MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT TO PREVENT THE PLUG FROM LOOSENING.
ATTENTION : POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAMELA PLUS
3
LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISEET Pot JSSER
JUSQU'AU FOND.
SAVE THESE INSTRUCTIONS
Operation instruction
The HEATER can be operated by the manual controls located on the
Control panel (as shown in FIGURE 2) or by your remote control
(shown in FIGURE 1).
(FIGURE 2)
1. Place the Heater on a firm, level surface.
2. Insert the plug into a sized electrical socket (must be able to bear
2000W or above) . Turn on the on/off switch in the rear of the unit
(FIGURE 3), when the heater is standing by, the indicator light will
4
be lit up.
(FIGURE 3)
3. Power: Turn the Heater ON by pressing the Power button, the LED
display will show the current room temperature. The power is under
High, press again and the power is off. All indicator lights are turned
off except the power light. After powered off, the fan blade will still
work for 30 seconds. Please press on/off switch to “O” after fan
blade stops working. (See FIGURE 2 and FIGURE 3)
4. Mode: Pressing the “Mode” button once, the Power is Low, pressing
the “Mode” button twice, the heater turns into “AUTO” mode,
pressing “Mode” button a third time, the heater turns into “high”
mode.
5. To turn the Heater OFF, press the Power button again and turn off
power switch. (See FIGURE 1 or 2 & 3)
6. For additional safety, there is a TIP OVER SWITCH under the
bottom of the heater. When the heater falls down, the heater will
stop working. When put back up, press “POWER” button to rework
again. Check the heater to make sure it is not damaged before use.
Remark: When switching the heater off, the Fan of Heater will continue
to work around 30 seconds which helps to cool down the heater.
OSCILLATION FUNCTION: This function will work in any mode.
Pressing the “OSC” button will allow the Heater to oscillate side by side.
To stop the oscillation, press the “OSC” button once more.
TIMER FUNCTION: The timer function allows you to set the length of
operation from 0.5 hour to 7.5 hours. Keep pressing Timer button to
increase hours.
5
Once the timer has been set, the timer will count down the hours in 1
hour increments, showing on the display the remaining operating time,
until the Heater will turn itself off. Pressing Timer setting button once
more after the display reflects 8 hours will reset the Heater to
continuously running.
TEMPERATURE INSTRUCTIONS (FIGURE 2)
1.To adjust SET temperature, press “MODE” button two times, the
Heater turns into “AUTO”. Press the TEMP. Button to (+) to increase the
desired temperature and press TEMP. (-) to decrease the desired
temperature. When all things are set, the LED will be blink 5 times, then
return to normal status.
2.When the air temperature reaches the SET temperature, the heater
will cut off.
3.When the air temperature drops the SET temperature, the unit will
operate again.
6
1.、Handle
2、Panel
- A: Mode
(High/Low/Auto)
- B: LED Display
- C: Timer
(0.5-7.5 hours)
- D: Control key
3、Remote control
signal receiver
4、 Air outlet
5、 Body
6、 Base
7、 Tip over switch
7
1. Install one ‘mercury’ (not
included) batteries to the
remote control.
2. Most of the functions
performed with the Remote
Control work identically to the
Manual Controls (Ionic
function needs to activated by
remote control).
3. When the remote control not
in used, store it into remote
control storage at rear cover
(See FIGURE 1A)
SAFETY FEATURES
1. A thermal overload protector is built in to prevent overheating;
2. When an overheat temperature is reached, the Heater will be
automatically shut off. It can only resume operation when the user
resets the unit.(See Reset instructions below)
To Reset Heater:
5. Unplug the Heater and wait 10 minutes for the unit to cool down.
Inspect it and remove any objects on or adjacent to the heater that
may cause overheating.
6. After 10 minutes plug the unit in again and operate normally.
7. Plug in the appliance and switch it on. If the appliance can not
operate normally, remove the plug immediately from the socket and
8
have the Heater serviced by an appointed service only.
Cleaning and Maintenance
MAINTENANCE
WARNING: ALWAYS UNPLUG THE UNIT BEFORE MOVING OR
SERVICING. DO NOT IMMERSE THE POWER CORD, PLUG OR THE
HEATER INTO WATER!
Cleaning:
Clean the heater grilles with a vacuum cleaner. This will remove lint and dirt
from inside of the heater. The rear cover of the heater can be removed, and
clean the mesh air filter with vacuum cleaner or under water, please
remember to dry it completely before mounting it back.
DO NOT ATTEMPT TO TAKE HEATER APART. Clean the body of
heater with a soft cloth.
Caution: Do not use gasoline, benzene , thinner, harsh cleaners, etc. and
never use alcohol or solvents for cleaning, it will damage the heater.
Storage:
Store the heater with this instruction manual in the original gift box in a cool,
dry place, and far away from children.
WARNIN
G:
To avoid danger of electric shock, unplug from outlet
when not in use and before cleaning. If the supply cord is
damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to
avoid a hazard.
Children of less than 3 years should be kept away unless continuously
supervised.
Children aged from 3 years and less than 8 years shall only switch
on/off the appliance provided that it has been placed or installed in its
intended normal operating position and they have been given
supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children aged from 3 years
and less than 8 years shall not plug in, regulate and clean the
appliance or perform user maintenance.
9
CAUTION — Some parts of this product can become very hot and
cause burns. Particular attention has to be given where children and
vulnerable people are present.
Any other servicing should be performed by an authorized service
representative.
DISPOSAL: Do not dispose this product as unsorted municipal
waste. Collection of such waste separately for special treatment is
necessary.
This product must not be disposed together with the domestic
waste. This product has to be disposed at an authorized place for
recycling of electrical and electronic appliances.
By collecting and recycling waste, you help save natural resources,
and make sure the product is disposed in an environmental friendly
and healthy way.
LIMITED WARRANTY
This unit is warranted against defective materials or workmanship for
one year from the date of purchase (warranty is only valid with a dated
proof of purchase). The warranty is valid for any manufacturing defects
only. This warranty covers operational defects incurred in normal use
and does not apply in the case of damage, abuse, mishandling,
accident, or failure to follow operation instructions. During the one year
warranty period, a product with a defect will be either repaired or
replaced with a reconditioned comparable model (at our option). Any
return of defective merchandise to the manufacturer must be processed
accordingly by contacting customer service first to obtain the Return
10
Authorization Number and freight prepaid with proof of purchase. We
will not accept any returns of merchandise without an applicable RMA#.
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement