GAT Access 6100 Access Control Terminal

GAT Access 6100 Access Control Terminal
GAT Access 6100
Access Control Terminal
Application
The GAT Access 6100 is a stylish terminal for access control in leisure
facilities such as swimming pools, spas and gyms. Identification at
the terminal is by contact-free RFID data carrier (Radio Frequency
Identification).
Information display for user guidance is realised via a graphical mono­
chrome display (LCD). The different versions (see order information) give
technological flexibility.
Function description
Order information
The GAT Access 6100 reads contact-free data carriers and checks and
Description
grants authorisations. The user holds the data carrier over the round
scan field and selects the required service via the acknowledge key. The
integrated 4-segment LED display, monochrome LCD display and acoustic
signal indicate authorisation.
Further functions:
•Activation of turnstiles, doors etc. via relay output
•Feedback input
GAT Access 6100 B
PartNo.
651681
Access control terminal with monochrome display (LCD)
and contact-free reader for LEGIC ® data carriers
GAT Access 6100 F
776487
Access control terminal with monochrome display (LCD)
•User guidance via monochrome display (LCD), 4-segment LED display,
illuminated round scan field and beeper
•Secure data transmission between reader and data carrier
•RFID frequency 13.56 MHz
and contact-free reader for MIFARE® data carriers
GAT Access 6100 ISO
651782
Access control terminal with monochrome display (LCD)
•Reading of LEGIC®, MIFARE ® standard and ISO 15693 data carriers
and contact-free reader for ISO 15693 data carriers
(depending on device type)
•Opening of housing only possible with special tool
•Plug & Play installation
Accessories
Description
GAT Access 6100 Manual
PartNo.
---
Operating and configuration instructions
GAT Reader WK
581683
Tool to open the reader housing
www.gantner.com
Valid as from September 16 th 2009 • Technical data subject to modifications without notice!
DB_GAT-ACCESS6100_ EN _10.indd • PartNo.: 860279
1
Technical data
Nominal voltage:
12/24 VDC (SELV - safety extra-low
voltage)
Permitted input voltage:
10 to 28 VDC
Aver. power consumption:
10 W
Data storage:
Internal EEPROM memory for
configuring and booking memory,
data preservation min. 10 years
Internal clock:
Data preservation approx. 12 h
(Gold-Cap)
Reader type:
See order information
Frequency reading field:
13.56 MHz
Control elements:
-4 function keys
-RFID reader
Display elements:
-Full graphics monochrome display
(LCD) with white LED background
lighting, resolution 128 x 64 pixels,
visible area 50 x 25 mm
-RFID reader (illuminated)
-Acoustic signal
-4-segment LED display with
different colours
Host interface:
Signal input:
1 x optocoupler (configurable)
- Input voltage: 0 to 30 VDC
ULow < 2 VDC, UHigh > 6 VDC
- Input current: 4.5 mA
Signal output:
1 x relay (configurable NO/NC)
- Switching voltage: max. 30 VAC/DC
- Continuous current: max. 2 A
- Switching power: max. 60 VA
Connection terminals:
0.5 to 1.5 mm2
Housing material:
- Upper part: plastic PMMA
- Back part: plastic PC-ABS
Dimensions:
93 x 107 x 33 mm
Permitted ambient temperature: -10 to +55°C
Storage temperature:
-20 to +70°C
Relative humidity:
20 to 80%, non-condensing
Protection type:
IP 54
Protection class:
III
Weight:
0.2 kg
Environment class
based on VDS 2110:
II (conditions in indoor areas)
Ethernet 10/100 MBit/s
Dimensions
24 mm
1. 4-segment LED display
1
2. Monochrome display (LCD)
3. Function keys
107 mm
2
4. Illuminated, round scan field
5
3
6
5. Device back part
6. Device upper part
4
93 mm
33 mm
Typical application
GAT Access 6100
Power supply
Network
Turnstile
2
Valid as from September 16 th 2009 • Technical data subject to modifications without notice!
DB_GAT-ACCESS6100_ EN _10.indd • PartNo.: 860279
www.gantner.com
Mounting and installation instructions
The device back part is secured by screws to a flat background (e.g.
Wall mounting
concrete wall). When fixing to an uneven background the device back part
Cables can be flush (1) or suface-mounted (2).
must not be distorted as this will prevent correct connection of the upper
When surface mounting please check whether the cables can still be
part. Recommended mounting height: top edge of device 1.3 m.
inserted once the device back part has been mounted, otherwise run the
Use the drilling template which is attached to the device.
cables through the cable lead-ins prior to securing.
69 mm
28,5 mm
20 mm
18,5 mm
60 mm
4
1. Flush-mounted cable
2. Surface-mounted cable
71 mm
1
3. Back box
3
4. Device back part
5. Cable conduit for suface cable connection
2
5
13 mm
Mounting the device upper part
Once the connection cables are terminated, the device back part and upper
part are connected together via a connection cable (already connected in
the upper part) and the two parts are fixed together.
1.
3.
2.
4.
Notes:
1. Check the socket in the device back part (circled in figure 1). Dirt,
3. Swing down the device upper part until it clicks.
dust and humidity must be removed so that a good contact of the
4. The device can only be opened with the supplied special tool! With
connection cable is guaranteed. No aggressive detergent may be
this the two catches on the bottom of the device can be unlocked in
used. Please do not damage socket contacts.
succession.
Attention: Cleaning only in powerless state.
2. Plug in the connection cable into the socket in the device back part
(consider alignment) and clip the top of the device upper part into the
device back part.
www.gantner.com
Valid as from September 16 th 2009 • Technical data subject to modifications without notice!
DB_GAT-ACCESS6100_ EN _10.indd • PartNo.: 860279
3
Electrical connections
TCP/IP with external power supply
GAT Access 6100
e.g. Turnstile
B
A
GND
VOut+
Mains power
Motor control
Power supply unit
e.g. GAT Power Supply SP014/1
TCP/IP
M
Feedback control
GND
TX +
TX RX +
RX -
VIN +
IN1 +
IN1 C1
NO 1
3
Network
Relay output
Ethernet, Connection via screw terminals.
For activation of devices like turnstiles etc.. The relay contact is of type
NO (maker contact). Please observe the max. permitted switching voltages
Power supply
and currents (see technical data).
DC supply (see technical data), e.g. via GANTNER GAT Power Supply
Depending on the connected instalation (e.g. turnstile) an additional free-
SP014/1. The power input is protected against reverse-polarity.
wheeling diode may be necessary, which is used to limit the switch-on
current. Please read the documentation of the connected installation.
Recommended cables
Ethernet: min. CAT 5 (STP) for 100 MBit
Optocoupler input
Input for status acquisition. For using the input a supply voltage must be
Wire colours
applied. This voltage can be taken from the terminal‘s supply or from an
Ethernet 10/100 MBit
external power source. Please observe the max. permitted input voltages
568A
568B
and currents (see technical data).
TX +
green/white
orange/white
TX -
green
orange
RX +
orange/white
green/white
RX -
orange
green
Connection to the device upper part
Attention: The socket (3) for the connection cable between the device
back part and the device upper part must be clean in order to guarantee
a good contact.
Safety instructions
- This device must be installed by qualified personnel only.
- The applicable safety and accident prevention regulations
must be observed.
- Safety devices must not be removed.
- Please observe the technical data of the device specified
on the data sheet.
- The device must be disconnected from the power supply
prior to installation, assembly or dismantling.
4
Valid as from September 16 th 2009 • Technical data subject to modifications without notice!
DB_GAT-ACCESS6100_ EN _10.indd • PartNo.: 860279
www.gantner.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising