advertisement
Manual
LED Pad 12 12x8W 4in1
RGBW
Table of contents
1.
Safety instructions ............................................................................................................................ 3
1.1.
For safe and efficient operation ............................................................................................... 3
2.
Designated use ................................................................................................................................ 4
2.1.
Overhead installation ............................................................................................................... 5
3.
Introduction ....................................................................................................................................... 7
4.
Connections ..................................................................................................................................... 7
4.1.
Electrical connections .............................................................................................................. 7
4.2.
DMX connections .................................................................................................................... 7
4.3.
DMX connection with terminator.............................................................................................. 7
5.
Control .............................................................................................................................................. 8
5.1.
Structure of the menu .............................................................................................................. 8
6.
DMX chart ........................................................................................................................................ 9
6.1.
DMX mode 1 (8 channel) ......................................................................................................... 9
6.2.
DMX mode 2 (4 channels) ....................................................................................................... 9
6.3.
DMX mode 3 (5 channels) ....................................................................................................... 9
6.4.
DMX mode 4 (8 channels) ....................................................................................................... 9
7.
Technical data ................................................................................................................................ 10
2 / 12
1. Safety instructions
•
This device is
•
All modifications to the device will void the warranty.
•
Repairs are to carry out by skilled personnel only.
•
Use only fuses of the same type and original parts as spare parts.
•
Protect the unit from rain and humid ity to avoid fire and electric shocks.
•
Make sure to unplug the power supply before opening the housing.
Any troubles arose, remove the power plug soon, and contact with an engineer for repairing, do not e plug from the receptacle, be sure to hold the plug. When not using the device for an extended period of time, be sure to disconnect the plug from the receptacle.
Important:
Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or problems. Make sure the electrical connection is carried out by qualified personnel. All electrical and mechanical connections
3 / 12
2. Designated use
This device was developed for professional use on stages, in discos, theatres etc. The device is only approved for a connection up to 230V 50/60 Hz AC voltage and only for indoor use.
Regular breaks during operation increase the lifetime of your device.
Avoid convulsions or any form of forceful impact during the installation or the start-up of the device.
Make sure that the device is not exposed excessive heat, humidity or dust at the place of installation.
Take care that no cables are lying around. You would endanger your own safety and also the safety of a third party.
It is not allowed to operate or store the device in an environment in which spray water, rain, humidity or fog is expected. Humidity or very high atmospheric humidity could reduce the isolation of the device and could cause deathly electric shocks. If you use fog devices the device has not be exposed to a direct smoke jet. There has to be a safety distance of at least 0,5m between this device and the fog machine. Make sure that the saturation of the fog has to enable a visibility of at least 10m.
Operate the device not during thunderstorms. Surge voltages could destroy the device. Unplug the power supply during thunderstorms.
During the installation the use of the mounting bracket is obligatory.
Surrounding objects or surfaces should not be in contact with the device. And make sure that there is a distance of at least 0.2m between the lenses and illuminated objects.
Make sure that during the installation and removal of the device the area below the place of installation is basically cordoned off. This also applies to implementation of service.
The device has basically been protected by a suitable safety.
Make familiar yourself with the functions of the device before start-up. People without the experience should not handle with the device. The most cause of functional disorder is inappropriate handling.
Do not use chemicals or volatile liquids for cleaning. Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt.
For transport use the original packing or designated accessory to avoid damages during the transport.
For reasons of safety unauthorized changes are forbidden.
A usage of the device which differs from usages which are described in this manual can cause damages of the device. In that case the warranty expires. Additional you should notice that every differed usage is related with dangers and can cause e.g. an electrical short, fire, electric shock or crash.
4 / 12
You have to observe the regulations of BGV C1 (formerly VBG 70) and
Installations are to carry out by skilled personnel only.
to be build and measured so they can withstand for an hour the tenfold
Basically installation has to be made by using a second separate suspension. This can be e.g. a second suspension must be designed and attached so no part of the installation can fall down in case of failure.
During construction, reconstruction and deconstruction unnecessary stay in the range of moving k stations or any other danger zones is forbidden.
• up or after critical changes before restarting it has to be checked by an expert.
• me of the inspection test at least all four years by an expert. .
•
Review by a qualified person at least once a year. the own weight of the device.
5 / 12
The maximum drop exceed must not exceed 20cm.
A safety rope once exposed to failing load or damaged may not be used furthermore.
Adjust the desired inclination angle via the mounting bracket and tighten the screw.
6 / 12
3. Introduction
Thank you for buying the LED Pad 12 12x8W 4in1 RGBW. It is a powerful device.
For a successful installation and operation, please read this manual carefully.
4. Connections
4.1. Electrical connections
If you wish to change the power supply settings, see the chapter Appendix. Connect the fixture to the mains with the enclosed power cable and plug. The earth has to be connected.
Cable (EU) Cable (US) Pin International
Brown
Light blue
Yellow/Green
Black
White
Green
Live
Neutral
Earth
L
N
4.2. DMX connections
To make a DMX512 connection go ahead like it is described in the picture. Make sure that you use shielded cable. 3pole or 5pole XLR cables are suitable.
Important! After the last device the line has to be terminated. In order to do this you have to solder a 120 Ω resistor between the pins Data + and Data -. You can solder this end resistor on a 3pin or
5pin XLR: Plug this adapter into the DMX output of the device.
4.3. DMX connection with terminator
Where the DMX cable has to run a long distance or the equipment is operated in an electrically noisy environment like a disco for installations, we recommend using a DMX terminator. This prevents corruption of the digital control signal by electrical noise. The DMX terminator is simply an XLR connector with a 120 Ω resistor between pins 2 and 3, which is then plugged into the XLR output socket of the last device in the series. Please look to the bottom drawings.
7 / 12
5. Control
Press MENU, to get to the menu. With UP/DOWN you can choose the required submenu. Confirm with ENTER. With UP/DOWN you can make the required settings. Confirm with ENTER. By pressing
MENU you can step back to the main menu.
SLAV rEno
Uer
Menu
Addr
Chnd
Auto
CoLo
Stat
5.1. Structure of the menu
SoUn
Submenu 1 Submenu 2 Submenu 3 Function
A001 – A512
1Ch
4Ch
5Ch
Setting the DMX address.
Choosing the DMX mode.
8Ch
Aut1 – Aut2
SLA
On/Off
SP1 – SP9
Co01 – Co51 St00 – St99
Red
GrEE bLue
UhiE
SoU1 r000 – r255
G000 – G255 b000 – b255
U000 – U255
Sen0 – Sen9
St00 – St99
St00 – St99
Choosing an automatic program, setting the speed and also the speed for strobe.
Choosing a preset color and setting the speed for strobe.
Dimmer red 0 – 100% and setting the speed for strobe.
Dimmer green 0 – 100% and setting the speed for strobe.
Dimmer blue 0 – 100% and setting the speed for strobe.
Dimmer white 0 – 100% and setting the speed for strobe.
Choosing a sound-to-light mode and setting the sensitivity for microphone.
Activates the Master-Slave mode.
(De-)Activates the remote.
Shows the current software version.
8 / 12
6. DMX chart
6.1. DMX mode 1 (8 channel)
Channel
1
Value from Value to
0 255
6.2. DMX mode 2 (4 channels)
Channel
1
2
3
4
Value from Value to
0
0
0
0
255
255
255
255
6.3. DMX mode 3 (5 channels)
Channel
1
2
3
4
5
Value from Value to
0
0
0
0
0
255
255
255
255
255
7
8
9
6
6.4. DMX mode 4 (8 channels)
Channel
1
2
3
4
5
0
0
10
Value from Value to
0 255
0
0
0
255
255
255
0
0
51
102
153
204
255
50
101
152
203
255
255
9
255
Function
51 preset colors.
Function
Dimmer red 0 – 100%
Dimmer green 0 – 100%
Dimmer blue 0 – 100%
Dimmer white 0 – 100%
Function
Dimmer 0 – 100%
Dimmer red 0 – 100%
Dimmer green 0 – 100%
Dimmer blue 0 – 100%
Dimmer white 0 – 100%
Function
Dimmer 0 – 100%
Dimmer red 0 – 100%
Dimmer green 0 – 100%
Dimmer blue 0 – 100%
Dimmer white 0 – 100%
No function
Automatic program 1
Automatic program 2
Sound-to-light mode 1
Sound-to-light mode 2
Setting the speed or the sensitivity for microphone for channel 6.
No function
Strobe slow - fast
9 / 12
7. Technical data
Power supply
Voltage
Power consumption max.
Light source
LM type
Power
Number / Power
Optics
Beam angle
Connections
Power in
XLR in/out
Controlling
Sound-to-Light
Automatic
Master-Slave
DMX512
Number of channels
Hardware
Protection class
Suitability
Weight
110 – 240 V / 50-60 Hz
110 W
LED 4in1
96 W
12 x 8 W
25°
IEC
3pol
Yes
Yes
Yes
Yes
1 / 4 / 5 / 8 channels
IP20
Indoor
2,10 kg
10 / 12
11 / 12
Importer:
B & K Braun GmbH
Industriestraße 2
D-76307 Karlsbad www.bkbraun.com
[email protected]
12 / 12
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Safety instructions
- 3 For safe and efficient operation
- 4 Designated use
- 5 Overhead installation
- 7 Introduction
- 7 Connections
- 7 Electrical connections
- 7 DMX connections
- 7 DMX connection with terminator
- 8 Control
- 8 Structure of the menu
- 9 DMX chart
- 9 DMX mode 1 (8 channel)
- 9 DMX mode 2 (4 channels)
- 9 DMX mode 3 (5 channels)
- 9 DMX mode 4 (8 channels)
- 10 Technical data