Earn BISSELL Rewards!

Earn BISSELL Rewards!
Earn BISSELL Rewards!
Register your
product today!
See details on
back page
USER'S GUIDE
Remanufactured 92L3 SERIES
2
Thank You
3
Safety instructions
4
Product view
5
Assembly
6-9
Operations
10-15
Maintenance and care
16-17
Troubleshooting
17
Replacement parts
18
Accessories
19
Warranty
20
Product registration
20
Consumer services
Thanks for buying a BISSELL Vacuum
We’re glad you purchased a BISSELL vacuum. Everything we know
about floor care went into the design and construction of this
complete, high-tech home cleaning system.
Your BISSELL vacuum is well made, and we back it with a limited
comprehensive 90 day warranty. We also stand behind it with
a knowledgeable, dedicated Consumer Services department, so,
should you ever have a problem, you’ll receive fast, considerate
assistance.
My great-grandfather invented the floor sweeper in 1876. Today,
BISSELL is a global leader in the design, manufacture, and service
of high quality homecare products like your BISSELL upright
vacuum.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
Chairman, President & CEO
2
www.bissell.com800.237.7691
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic
precautions should be observed, including
the following:
Read all
instructions
before using your
Upright VACUUM.
Always connect to a polarized outlet
(left slot is wider than right). Unplug from
outlet when not in use and before conducting
maintenance.
■ Keep hair, loose clothing, fingers, and all
■
■
■
■
WARNING:
■
■ Do not modify the polarized plug to fit a
■
■
■
To
reduce the risk of fire,
electric shock, or injury:
■
■
■
■
■
■
■
■
■
■
■
■
■
non-polarized outlet or extension cord.
Do not leave vacuum cleaner unattended
when it is plugged in.
Unplug from outlet when not in use and
before servicing.
Unplug before attaching the TurboBrush.
Do not use outdoors or on wet surfaces.
Do not allow children to operate vacuum
cleaner or use as a toy.
Close attention is necessary when used
by or near children.
Do not use for any purpose other than
described in this user’s guide.
Use only manufacturer’s recommended
attachments.
Do not use with damaged cord or plug.
If appliance is not working as it should,
has been dropped, damaged, left outdoors, or dropped into water, have it
repaired at an authorized service center.
Do not pull or carry by cord, use cord as
a handle, close a door on cord, or pull
cord around sharp edges or corners. Do
not run appliance over cord. Keep cord
away from heated surfaces.
Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
Do not handle vacuum cleaner or plug
with wet hands.
Do not put any object into openings. Do
not use with any opening blocked; keep
openings free of dust, lint, hair, and anything that may reduce air flow.
■
■
■
■
parts of body away from openings and
moving parts.
Turn off all controls before plugging or
unplugging vacuum cleaner.
Use extra care when cleaning stairs.
Do not pick up flammable materials
(lighter fluid, gasoline, kerosene, etc.) or
use in the presence of explosive liquids
or vapors.
Do not pick up toxic material (chlorine
bleach, ammonia, drain cleaner, etc.).
Do not use vacuum cleaner in an
enclosed space filled with vapors given
off by oil base paint, paint thinner, some
moth proofing substances, flammable
dust, or other explosive or toxic vapors.
Do not pick up hard or sharp objects
such as glass, nails, screws, coins, etc.
Do not pick up anything that is burning or
smoking, such as cigarettes, matches, or
hot ashes.
Do not use without filters in place.
Use only on dry, indoor surfaces.
Keep appliance on a level surface.
Do not carry the vacuum cleaner while it
is running.
SAVE THESE
INSTRUCTIONS
FOR FUTURE USE
THIS APPLIANCE
HAS A POLARIZED
PLUG.
To reduce the risk of electric shock, this
appliance has a polarized plug (one blade
is wider than the other). This plug will fit in
a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified
electrician to install a proper outlet. Do not
change the plug in any way.
This model is for household use only.
www.bissell.com800.237.7691
3
Product view
Handle
Hose Clip
Stretch Hose
Dusting Brush/
Upholstery Tool
TurboBrush®
Quick
Release™
Cord Wrap
Carry Handle
Crevice Tool
Twist ‘n Snap™
Hose
Power Switch
Inner Cyclone
Extension
Wand
Upper Tank
Easy
Empty™
Dirt
Container
Power
Cord
Hose
Wand
HEPA Media
Post Motor
Filter
Washable
Pre-Motor
Filter
Headlight
Lock ‘n Seal® Lever
Handle
Release Pedal
Height Adjustment
Knob
Foot
Window
Hose Wand Base
Wide Cleaning Foot
4
www.bissell.com800.237.7691
Assembly
The only tool you’ll need to assemble
your vacuum cleaner is a Phillips
screwdriver.
caution:
Do not plug in your vacuum
Attach handle to vacuum
cleaner until you are familiar with
all instructions and operating procedures.
1. Locate the handle and cord wrap. Remove
the screw packet taped to the handle.
2. Stand the vacuum upright and from the 2.
rear of the unit, slide the base of the
handle firmly into the grooves at the top
of the vacuum body.
4.
3. Ensure that the handle fits firmly to the vacuum
body. If there are any gaps, continue to push
firmly until the handle is secure.
4. Insert the provided screw into the existing hole, attaching the handle to the
body of the vacuum. Tighten securely
with a screwdriver.
Attach vacuum hose and tools
1. Attach the Twist ‘n Snap™ Hose by lining up
the tabs on the base with the corresponding
notches on the back of the vacuum as shown.
1.
3.
2. Turn the Twist ‘n Snap Hose to the right
to lock the hose into place.
3. Grasping the Quick Reach® Handle,
slide the end of the Hose Wand onto the
Hose Wand Base. Snap the Hose into
the Hose Clip.
NOTE: The vacuum will not operate
effectively unless the hose wand is
firmly attached.
4. Slide the extension wand and crevice tool
into the storage clip on back of vacuum.
Twist 'n
Snap Hose
6.
5. Slide the dusting brush/upholstery tool
into the storage clip on back of vacuum.
6. Store the TurboBrush® on the front of the
handle by lining up the TurboBrush base
with the base of the holder then push
back to snap into place.
Power switch
The Power Switch is located on the left
side of the vacuum. Push the rocker
switch “ON” (I) to vacuum, and “OFF”
(O) when cleaning is complete.
caution:
Before using your vacuum, make
sure that the dirt container is in
locked position and that all filters (inner circular, outer circular,
pre-motor and post-motor) are
in place. Do not operate your
vacuum without these filters.
www.bissell.com800.237.7691
5
Operations
Handle positions
Press the handle release pedal, located
on the lower left side of the vacuum, with
your foot to place your vacuum into one
of three cleaning positions.
1.Upright – For storage and above floor
cleaning with tools.
2.Normal Cleaning – Press handle
release pedal once. Position used for most
household floor cleaning tasks.
3.Low Cleaning – With the vacuum in
normal cleaning position, press handle
release pedal again. Use for reaching
under low furniture such as tables, chairs
or beds.
NOTICE:
For above floor cleaning, the floor
brush will continue to rotate, but is
raised above floor. To prevent carpet
damage, do not lean on the vacuum
or let the powerfoot tilt forward.
CAUTION:
To avoid personal injury and to
prevent the cleaner from falling
when cleaning stairs, always
place it at the bottom of the
stairs.
Height adjustment
There are five height settings available
for various floor surfaces. Turn the dial
on the foot of the cleaner to the desired
setting.
Lowest setting – For low pile carpet or bare
floors. To pick up debris it may be necessary to
move up one setting.
Medium settings – For medium pile carpet.
High setting – For high pile and most shag
carpet.
Note: For optimal carpet cleaning
performance, adjust to the lowest
practical setting. If your cleaner is
difficult to push, adjust to the next
higher setting.
If the dial is difficult to turn, tilt the
cleaner back slightly to take the weight
off the foot while turning.
1.
2.
3.
Tip:
Before cleaning under low furniture,
check area first for objects that might
harm the unit or block the vacuum hose.
1.
Height Adjustment Knob
6
www.bissell.com800.237.7691
Operations
Transporting cleaner
1.
1. To move your cleaner from room to
room, put the handle in the upright
position, tilt the cleaner back on its rear
wheels and push forward.
2. The cleaner can also be moved by
using the carry handle.
Special on-board tools
Select models only
Your vacuum is not only a powerful carpet and rug cleaner, it’s also a
versatile above floor vacuum cleaner
when you select one of the special
tools.
1. Raise the handle to the upright position.
correct way to
2. carry
2. Grasp the hose wand handle to separate from hose wand base.
3. Attach tools by firmly pushing onto
vacuum hose, hose wand or extension
wand. Be sure the hose and tool fit
snuggly together by twisting tightly.
Dusting Brush/Upholstery Tool:
Two types of cleaning tools in one
attachment.
• Use brush side to dust furniture,
blinds, books, lamps, shelves and
baseboards.
• Use upholstery side for cushions,
draperies and fabrics.
Dusting Brush/
Upholstery Tool
Crevice Tool
Extension Wand
Hose Wand
Hose Wand
Base
www.bissell.com800.237.7691
7
Operations
Special on-board tools (continued)
Crevice Tool: Use in tight narrow spaces.
Extension Wand: Use with desired attachment for a longer reach.
Hose Wand: Use with desired attachment
for a longer reach or for cleaning hard to
reach places.
TurboBrush: Use rotating brush action for
small flat areas such as cushions and
beds.
Dusting Brush/
Upholstery Tool
Crevice Tool
Extension Wand
Hose Wand
NOTE: Press gently down and pull
towards you in a raking motion. Too
much pressure will cause the brush
to stop rotating.
Hose Wand
Base
TurboBrush
Tip:
Hair, string and small objects can block
the vacuum hose or tools. Check them
occasionally for obstructions.
The rotating
CAUTION:
floor brush continues to rotate while tools are in use. To reduce the risk of injury
from moving parts, always move the cleaner with the carrying handle. Always place vacuum
cleaner on the floor with handle in upright position when using tools. Never place your fingers
under the cleaner when it is running. Never place powerfoot on furniture or uneven surfaces.
Do not place vacuum cleaner close enough to objects to pull them into rotating brush.
8
www.bissell.com800.237.7691
Operations
Power cord usage
1. To use your vacuum, remove the cord and
1.
plug it into an electrical outlet. For your
convenience, there is a quick release cord
wrap for easy cord removal. There is also
a cord clip that is part of the upper cord Quick Release
wrap where you can attach the cord when Cord Wrap
vacuuming.
2. When you are finished cleaning, turn
vacuum cleaner off.
3. Unplug power cord by grasping the
polarized plug (NOT the cord) and disconnect from outlet.
4. Loop power cord around cord wraps on
side of vacuum cleaner. Be sure to first
return the quick release cord wrap back to
its original position before wrapping the
cord.
5. Clip molded plug to power cord to secure.
www.bissell.com800.237.7691
9
Maintenance and care
To maximize your cleaning performance and extend the life of your
vacuum, it is very important that you
empty your dirt container and check
and clean your filters frequently.
Perform the following maintenance
steps:
1. Empty the dirt container when the dirt reaches
the “Full” line on the container, or more
frequently to prevent overfills. For best performance, empty after each use.
2. Check the pre-motor filter and clean or
replace as necessary.
3. Check the post-motor HEPA media filter
and replace as needed.
NOTE: More frequent filter cleaning may be necessary if you are
vacuuming new carpet, fine dust, or
have allergy concerns. Follow the
instructions on the following pages
to perform these simple maintenance
steps.
WARNING:
To reduce the risk of electric
shock, turn power switch OFF and
disconnect polarized plug from
electrical outlet before performing
maintenance or troubleshooting
checks.
Tip:
For maximum cleaning performance,
check and clean or replace all filters
as suggested.
2.
Empty dirt container
The dirt container should to be emptied
before the dirt reaches the “Full” line on
the container.
1. Unplug the vacuum from electrical outlet.
2. Slide the Lock ‘n Seal Lever to the
“Unlock” position.
Unlock
4.
3. Grasp handle and pull the dirt container
straight out to remove from the vacuum.
3. Empty dirt into garbage container.
NOTE: Emptying the dirt container
after every use will help prevent
over filling and ensure that the
vacuum is ready to go the next time
you clean.
10
www.bissell.com800.237.7691
Maintenance and care
Cleaning the pre-motor and post-motor HEPA media filters
1. Unplug the vacuum from electrical outlet.
Post-Motor
HEPA
Media
Filter
2. The pre-motor filter protects the motor from
dirt particles. It is located in the slide out
tray underneath the dirt container. If the
filter becomes dirty, pull out the tray, lift
out the foam filter pad and clean it.
NOTE: The pre-motor filter may be
hand washed in cold water with mild
detergent. Rinse well and air dry thoroughly before replacing.
3. The post-motor HEPA media filter assists
in the filtration process to return clean air
to the room. It is located behind the door
on the side of the vacuum. If the filter
becomes dirty, remove the door, remove
the filter and replace.
Washable
Pre-Motor
Filter
WARNING:
NOTE: The post-motor filter is
a white, pleated HEPA media
filter. This filter is not washable
and must be replaced when it
becomes dirty.
Do not operate cleaner with
damp or wet filters or without all
filters in place.
Check rotating floor brush and drive belt
You should check your vacuum cleaner’s
rotating floor brush and drive belt regularly
for wear or damage. You should also clean
the brush and brush ends of strings, hair
and carpet fibers. This type of debris can
wrap around the brush and hamper its
ability to effectively clean your carpet. Also
remove any debris that has accumulated
under the brush cover.
1. Unplug the vacuum from electrical outlet.
2. Place handle in low position and turn vacuum cleaner over so bottom side is facing up.
WARNING:
To reduce the risk of injury from
moving parts, turn vacuum cleaner
off and disconnect power plug
from electrical outlet.
3.
1
3. Lift tab 1 and release the three latches in
order 2-4 marked. Lift off the brush cover.
4. Grasp rotating floor brush at both ends and lift.
2
3
4
5. Clean strings, hair and other debris from
rotating floor brush, paying particular
attention to brush ends.
6. Clean strings, hair and other debris from
motor pulley and drive belt areas.
www.bissell.com800.237.7691
11
Maintenance and care
Check rotating floor brush and drive belt continued
7. Check drive belt carefully for wear, cuts or
stressed areas.
8. Check air passageway for obstructions.
Remove debris from this area.
Replace drive belt
8.
Motor
Pulley
1. Unplug the vacuum from electrical outlet.
2. With rotating floor brush removed from
vacuum cleaner (Steps 1-4 of check rotating floor brush and drive belt), grasp old
drive belt and remove from motor pulley.
Discard the old drive belt.
3. Place new drive belt over motor pulley
and loop other end over rotating floor
brush in the space between the bristles.
NOTE: It is important that you use
only genuine BISSELL replacement
belts. Generic belts may not meet
the exactspecifications required to
keep your vacuum operating at
its peak performance. The use of
unbranded belts could lead to early
failure of the vacuum and could void
your warranty.
Air Passageway
Motor
Pulley
3.
4. Pull the rotating floor brush firmly into
position, stretching the drive belt, and
place ends of rotating floor brush
down into the slots on sides as shown.
Alignment of brush ends in slots may be
necessary to fully insert the brush.
5. Turn rotating floor brush by hand several
times in the direction of motor pulley. If
properly installed, drive belt will center
itself on rotating brush crown.
6. Insert front edge of brush cover, rotate into
place, and snap 3 latches.
12
www.bissell.com800.237.7691
Maintenance and care
Replace light bulb
2.
1. Unplug the vacuum from electrical outlet.
2. Using a screwdriver, first remove 2 screws
on either side of lens and pull out to
remove the lens.
3. Remove the bulb from the socket by
grasping the bulb and pulling gently.
Install the new bulb by pushing it gently
into the socket until the bulb snaps into
place.
4. Reposition the lens, place cover back over
headlight and reinsert 2 screws.
3.
4.
TurboBrush maintenance
The TurboBrush should be checked
regularly for clogs or debris wrapping
around the brush.
1. Remove tool from hose or front of vacuum.
2.
2. Twist collar so opening is at the top and
lift top cover to remove.
4.
3. Remove the brush from the belt and clean
debris.
4. Replace the brush inside the belt and
place ends into slots on sides as shown.
5. Reposition top cover making sure to line
up inside tab at the front with the opening
on the cover. Twist collar until opening is
at the bottom to lock into place.
5.
www.bissell.com800.237.7691
13
Maintenance and care
Cleaning clogs
Low suction or poor pickup may be
due to a clog in the vacuum cleaner. If
you notice a change in the sound of the
motor, check for clogs.
1. Unplug the vacuum from electrical outlet.
2.
2. Empty dirt container.
3. Check upper tank for build up or clogs.
4. If you notice a clog in the upper tank,
remove the inner cyclone (see section
"Cleaning the upper tank" on page 16).
5.
5. Grasp the hose wand and separate it
from the hose wand base. Check for a
clog in the base, the wand or in the hose.
6. Remove the Twist ‘n Snap hose from the
vacuum by turning to the left. Straighten the
hose and unclog with a long, narrow object
such as a broom handle.
7. If the clog persists, follow the instructions
for "Checking the rotating floor brush and
drive belt" on page 12 and inspect the air
passageway for obstructions.
14
www.bissell.com800.237.7691
Maintenance and care
Cleaning the upper tank
1. Grasp the inner cyclone and twist to the left
until the locking tabs stop the rotation. Pull
down from the upper tank to remove it.
1.
2. Wipe out the inside of the upper tank
and the inner cyclone with a damp cloth
moistened with water or a mild cleaning
solution.
3. If you desire to thoroughly clean the filtration disk located in the upper portion of
the inner cyclone, hold the bottom of the
cyclone and turn filtration disk to the right
and pull up to remove.
3.
4. The inner cyclone and filtration disk may
be washed using a mild detergent. Be
sure it is completely dry before reassembling or damage to your unit may result.
5. Once cleaning is completed, reassemble
the filtration disk over the inner cyclone by
sliding it straight down on the top of the
inner cyclone and turning left. Be sure to
line up the tabs when reassembling for
proper installation.
6. To replace the inner cyclone, slide it into
the upper housing. Be sure to line up the
inner cyclone by ensuring tabs on filtration
disk are positioned toward the front of the
unit. Push the inner cyclone in and rotate
it to the right until the locking tabs stop the
rotation.
5.
6.
www.bissell.com800.237.7691
15
Troubleshooting
Vacuum cleaner won’t turn on
Possible causes
Remedies
1. Power cord not plugged in
1. Check electrical plug
2. Blown fuse/tripped breaker
2. Check/replace fuse or reset breaker
3. Damaged power cord
3. Unplug, check for damage, have cord replaced at an
authorized Service Center
Vacuum cleaner won't pick up dirt
Possible causes
Remedies
1. Incorrect height adjustment
1. Adjust powerfoot to correct height
2. Hose not attached to suction opening
2. Firmly push hose wand into hose wand base
3. Twist 'n Snap hose not securely attached
3. Make sure Twist 'n Snap hose is snapped
into locked position
4. Crack or hole in hose
4. Check hose and replace if needed
5. Broken or worn drive belt
5. Replace drive belt, see page 12
6. Rotating floor brush bristles worn
6. Replace brush
7. Rotating floor brush jammed
7. Remove brush and clean debris from brush ends
8. Clog in vacuum
8. Clear clogs, see page 14
9. Dirt container full
9. Empty dirt container
10. Dirt container not installed properly
10. Position correctly and lock in place
11. Filters are dirty
11. Check pre-motor and post-motor filters
12. TurboBrush is clogged or debris is wrapped
12. See page 13 for Maintaining TurboBrush around the
brush roll
Vacuum cleaner is difficult to push
Possible causes
1. Incorrect height adjustment
Remedies
1. Adjust powerfoot to correct height setting
Visible dirt escaping from cleaner
Possible causes
1. Dirt container full
Remedies
1. Empty dirt container
2. Filters missing or installed incorrectly
2. Check pre-motor and post-motor filters for
correct installation
3. Dirt container installed incorrectly
3. Pull out and re-insert dirt container correctly
Other maintenance or service not included in the manual should be
performed by an authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
For any questions or concerns, BISSELL is happy to be of
service. Contact us directly at 1-800-237-7691.
16
www.bissell.com800.237.7691
Replacement parts - BISSELL vacuum
Item
1
2
3
4
5
1
Part No.
303-1120
203-1297
203-1283
203-1073
203-6608
2
Part Name
Style 7/9/10/12/14 Drive Belt (2-Pack)
Headlight Bulb
Wide Window Foot Brush Roll (gray)
Style 7/8/14 Pre-Motor Foam Filter
Style 8/14 HEPA Media POST-Motor Filter
3
4
5
www.bissell.com800.237.7691
17
Accessories - BISSELL vacuum
These items are available for purchase as accessories for your
BISSELL vacuum: To purchase call
1-800-237-7691 or visit www.bissell.com.
Item
1
2
3
4
5
1
18
Part No.
203-1056
203-1059
203-1429 203-1068
203-1216
2
Part Name
Crevice Tool
Dusting Brush/Upholstery Tool
TurboBrush
Extension Wand
Twist 'n Snap Vacuum Hose (clear)
3
4
5
www.bissell.com800.237.7691
Warranty - BISSELL Vacuum
This warranty gives you specific legal rights, and you may also have other rights which may
vary from state to state. If you need additional instruction regarding this warranty or have
questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail,
telephone, or regular mail as described below.
Limited 90 day Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product
BISSELL Homecare, Inc. will repair or replace (with new or remanufactured components or
products), at BISSELL’s option, free of charge from the date of purchase by the original
purchaser, for 90 days any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This
warranty does not apply to fans or routine maintenance components such as filters, belts, or
brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any
other use not in accordance with the User's Guide is not covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your
area.
If you need information about repairs or replacement parts, or if you have questions about
your warranty, contact BISSELL Consumer Services.
Website or E-mail:
www.bissell.com
Use the “Customer Support” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
Or Write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids, MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT
EXCEED THE PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR
WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO THE 90 day DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty last so the above limitation
may not apply to you.
www.bissell.com800.237.7691
19
Don't forget to register your product!
Registering is quick, easy and offers you benefits over the lifetime of your product.
You’ll receive:
BISSELL Rewards Points
Automatically earn points for discounts and free shipping on future purchases.
Faster Service
Supplying your information now saves you time should you need to contact us with
questions regarding your product.
Product Support Reminders and Alerts
We’ll contact you with any important product maintenance reminders and alerts.
Special Promotions
Optional: Register your email to receive notice of offers, contests, cleaning tips and more!
Visit www.bissell.com/registration now!
BISSELL consumer services
For information about repairs or replacement parts, or questions about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. — 10 p.m. ET
Saturday 9 a.m. — 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It
provides proof of purchase date in the event of a
warranty claim. See Warranty on page 19 for details.
20
©2011 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in Mexico
Part Number 320-4054
Rev 1/11
Visit our website at:
www.bissell.com
www.bissell.com800.237.7691
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement