null  null
IMPORTANT SAFEGUARDS
STEREO RADIO CASSETTE RECORDER
COMPACT DISC PLAYER
GPS158RR/GPS158RS
Instruction Manual
PRE FITTED MAINS PLUGS
For your convenience a mains plug has been fitted to this appliance. For your safety please
observe the following information.
1. Should the fuse in the plug remove the plug from the wall socket and replace the fuse with a 3
Amp ASTA approved to BS 1362 fuse.
2. Never use the plug without the fuse cover fitted. Replacement fuse covers are available from
your dealer or most electrical retail outlets.
3. If the mains plug is cut off the cable, rewire the replacement plug in accordance with
instruction given in this manual.
4. CAUTION: Under no circumstances should the discarded plug be inserted mains socket. To
prevent a shock hazard carefully dispose of the discarded plug. Do not leave the plug lying
around where children might see it.
WARNING: To prevent fire or shock hazard do not expose this unit to rain or moisture.
CAUTION: DANGEROUS VOLTAGES EXIST INSIDE THIS UNIT, DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL. DISCONNECT FROM MAINS SUPPLY
WHEN NOT IN USE.
PLUG WIRING DETAILS
E
BLUE
N
L
FUSE
BROWN
CORD
GRIP
The wires in this mains lead are coloured in
accordance with the following wiring codes:
Blue................................................. Neutral
Brown................................................... Live
The wires in this mains lead must be
connected to the terminals in the plugs as
follows:
Blue Wire..................................... N or Black
Brown Wire..................................... L or Red
Only a 3 Amp fuse should be fitted in the plug
or a 5 Amp fuse at the distribution board.
WARNING: UNDER NO CIRCUMSTANCES MUST THE LIVE OR NEUTRAL WIRES BE
CONNECTED TO THE EARTH TERMINAL IN A 3-PIN MAINS PLUG.
SPECIFICATIONS
Programme Play ............................................Up to 20 tracks
This symbol means that this unit is double insulated.
An earth connection is not required.
Earphone output ............................................20mW x 2 (32 )
Power requirement ........................................AC 230V/50Hz
Dimension .....................................................Approx. 319(L) X 261.7(W) X 123.3(H) mm
Weight ...........................................................Approx. 2.244Kg (not including batteries)
HELPLINE PHONE NUMBER 0870 873 0080
For improvement purposes, specification and design are subject to change without notice.
Goodmans Product Information Helpline 0870 873 0080
CAUTION
IMPORTANT NOTES
CLASS 1 LASER PRODUCT
Use of Controls or adjustments or performance of procedures other than those specified herein
may result in hazardous radiation exposure.
LASER SAFETY
This unit employs a laser, only qualified service personnel should attempt repair.
DANGER: INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCK FAILED OR DEFEATED. AVOID DIRECT
EXPOSURE TO BEAM.
CAUTION: HAZARDOUS LASER RADIATION WHEN OPEN AND
INTERLOCK DEFEATED.
CAUTION
CLEANING: Always disconnect unit from mains supply before attempting to clean it. Use soft
cloth moistened with soapy water, wipe gently. Do not use solvents or abrasive
materials.
SOME DO'S AND DONT'S ON THE SAFE USE OF EQUIPMENT
This equipment has been designed and manufactured to meet European safety standards but
like any electrical equipment, care must be taken if you are to obtain the best results and safety is
to be assured.
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (Including the mains plug, extension leads and
interconnections between pieces of equipment) are properly made in accordance with the
manufacturer's instructions. Switch off and withdraw the mains plug when making or changing
connections.
Do consult your dealer if you are ever in doubt of the installation, operating, or safety of your
equipment.
Don't continue to operate the equipment if you are in any doubt about it working normally, or if it is
damaged in any way- switch off, withdraw the mains plug and consult your dealer.
Don't remove any fixed covers as this may expose dangerous voltages.
Don't leave equipment switched on when it is unattended unless it is specifically stated that it is
designed for unattended operation or has a standby mode. Switch off using the switch on the
equipment and made sure that your family knows how to do this. Special arrangements may need
to be made for infirm or handicapped people.
Don't listen to headphones at high volume, as such use can permanently damage your hearing.
Don't obstruct the ventilation of the equiment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
Don't allow electrical equipment to be exposed to rain or moisture.
Above all
Never let anyone, especially children, push anything into holes, slots or any other opening as
this could result in a fatal electric shock.
Never guess or take chances with electrical equipment of any kind.
It is better to be safe than sorry!
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE, DANGEROUS HIGH VOLTAGES ARE
PRESENT INSIDE THE ENCLOSURE, DO NOT OPEN THE CABINET, REFER
SERVICING TO QUALIFIED PERSONNEL ONLY.
Your hearing is very important to you and to us so please take care when operating
this equipment. The following guidelines are provided for your information.
ESTABLISH A SAFE SOUND LEVEL
— Over time your hearing will adapt to continuous loud sounds and will give the
impression that the volume has in fact been reduced. What seems normal to
you may in fact be harmful. To guard against this BEFORE YOUR HEARING
ADAPTS set the volume at a low level.
— Slowly increase the level until you can hear comfortably and clearly and without
distortion.
— Damage to your hearing is accumulative and is irreversible.
— Any ringing or discomfort in the ears indicates that the volume is too loud.
— Remember listening for prolonged period of time at high volume levels will
harm your hearing.
Once you have established a comfortable listening level, DO NOT INCREASE
THE SOUND LEVEL FURTHER.
The following list of typical sound levels may assist you in recognizing just how
loud you have set the volume level.
DECIBEL
Level dB
Example
30dB
40
50
60
70
Quiet library, soft whisper.
Living room, fridge freezer bedroom away from traffic.
Normal conversation, quiet office, light traffic.
Electric sewing machine.
Vacuum cleaner, hair dryer, noisy restaurant.
THE FOLLOWING NOISE CAN BE HARMFUL UNDER CONSTANT EXPOSURE
80dB
90
100
120
140
180
Average city traffic, alarm clock buzzer at 1 Metre, food mixer.
Motorcycle, heavy goods vehicle, petrol lawn mower.
Pneumatic drill, chain saw, garbage truck, discotec/night-club.
Rock band concert, thunderclap, fast train passing by.
THRESHOLD OF PAIN Gunshot, jet plane taking off.
Rocket Launching pad.
TABLE OF CONTENTS
SAFETY PRECAUTIONS
Power Sources ................................................. 1
Player Maintenance............................................ 2
Disc Cleaning, Power failure............................ 3
1. As the laser beam used in this compact
disc player is harmful to the eyes, do not
attempt to disassemble the casing.
Player Operation
Location of Controls........................................... 4
Radio operation................................................. 5
Listening to a compact disc.................................. 6
Program play operation......................................7
Repeat play operation.........................................8
Random play operation........................................9
Cassettes..........................................................10
Recording from Radio/MIC/CD........................... 11
Remote Control.................................................12
Product Specifications...................................... 13
WARNING
2. Stop operation immediately if any liquid or
solid object should fall into the cabinet.
Unplug the unit and have it checked by
qualified personnel.
3. Do not touch the lens or poke at it. If you do,
you may damage the lens and the player
may not operate properly.
1. POWER SOURCES
AC MAINS OPERATION
BATTERY OPERATION
1. Remove the AC cord which is packed
inside the box.
2. Connect the cord to the AC input
socket.
3. Connect the 3 pin mains plug to an AC
mains socket.
1. Insert 8 LR14 (C Size) batteries (not
supplied) into the battery compartment
observing the correct polarity as
indicated.
2. Ensure compartment cover is securely
fitted.
3. Product will only function from
batteries once AC cord is removed
from the unit.
4. When replacing flat batteries, ensure
all batteries are replaced at the same
time with the same type.
5. If the product is not to be used for an
extended period of time the batteries
should be removed to prevent any
possible damage to the product.
4. Do not put anything in the safety slot. If you
do, the laser diode will be ON when the lid
is still opened.
5. This unit employs a laser. The use of
controls or adjustments or performance of
procedures other then those specified
herein may result in exposure to
hazardous radiation.
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified
personnel only.
2. PLAYER MAINTENANCE
CASSETTE DECK MAINTENANCE
CLEANING THE LENS
When the heads, capstan and pinch roller
become dirty, this may result in muffled,
distorted or reduced sound during play back
and may even result in tape jams.
Clean the tape head with a head cleaning
tape.
If the lens in the CD pick-up is dirty, dusty,
etc, it could degrade the sound or prevent
disc play. Open the disc holder and clean
the lens as shown.
h Use a blower (available from camera
stores) to blow dust off the lens.
h If there are fingerprints, etc., on the
lens, gently wipe clean with a cotton
swab.
3. DISC CLEANING, POWER FAILURE
4. LOCATION OF CONTROLS
Cleaning the Disc
1. To handle a disc use only one of the two
manners illustrated.
1 2
9 10
5 7
11
4 6 8
3
12 13
NOTE: Do not touch the rainbow-colored
side.
2. To wipe a disc, use only a soft cloth. Do
not use benzene or thinner which will
damage the disc. The disc should always
be wiped in a straight line from the center
to the edge. It should never be wiped in a
circular motion.
3. Never place the disc on other equipment
or near any heat source. Avoid positions
where the disc would be subjected to
direct sunlight for long periods.
16 18 20 22 24 26 27 28
15 17 19 21 23 25
Maintenance and care
1. Electronic products should never be
subjected to extreme temperatures nor
high humidity to ensure good performance
and a long life-time. The player should not
be placed in bathing areas, or around
stoves and radiators, etc. Always leave
sufficient space around the unit for
ventilation.
2. If necessary, only clean the cabinet of the
unit with a soft dampened piece of cloth.
(be sure the AC power cord is unplugged
from the outlet) Never use a polish or a
strong detergent for cleaning since this
can damage the finish of the cabinet.
30
29
33
34
31 32 29
35
38
36
37
39
40
14
1. PHONES JACK
2. VOLUME CONTROL
3. FUNCTION SWITCH
4. PAUSE BUTTON
5. STOP/EJECT BUTTON
6. CD DOOR
7. FAST FORWARD BUTTON
8. REWIND BUTTON
9. PLAY BUTTON
10. RECORD BUTTON
11. FOLDING HANDLE
12. BAND SWITCH
13. TUNING CONTROL
14. DIAL SCALE
15. CD PROGRAM BUTTON
16. CD REPEAT BUTTON
17. RANDOM BUTTON
18. CD STOP BUTTON
19. POWER INDICATOR
20. FM STEREO INDICATOR
21. RANDOM INDICATOR
22. CD LED DISPLAY
23. CD PROGRAM INDICATOR
24. CD REPEAT INDICATOR
25. CD PLAY/PAUSE INDICATOR
26. CD PLAY/PAUSE BUTTON
27. CD SKIP/SEARCH BUTTONS
28. CD DOOR OPEN AREA
29. BUILT-IN SPEAKERS
30. CASSETTE DECK
31. REMOTE SENSOR
32. BUILT-IN CONDENSER MICROPHONE
33. TELESCOPIC AERIAL
34. BATTERY COMPARTMENT COVER
35. AC SOCKET
REMOTE CONTROL
36. CD BACKWARD SKIP/SEARCH BUTTON
37. BATTERY COMPARTMENT
38. CD PLAY PAUSE BUTTON
39. CD FORWARD SKIP/SEARCH BUTTON
40. CD STOP BUTTON
5. RADIO OPERATION
TO PLAY THE RADIO
1. Slide the FUNCTION Switch to RADIO
position.
2. Select required wave band with BAND
Switch.
3. Tune to required station by rotating the
TUNING Control.
4. Adjust this control back and forth slowly
until you get the strongest, clearest
sound.
5. The built-in MW aerial and the FM rod
aerial are directional. When receiving
FM broadcast, extend the FM
TELESCOPIC AERIAL to its full length.
The strongest reception can be achieved
by rotating the set for MW or rotating the
TELESCOPIC AERIAL for FM.
6. Adjust the VOLUME Control to your
listening taste.
7. To turn off the radio, slide the FUNCTION
Switch to TAPE (POWER OFF) position.
NOTE: FM Stereo is weaker than FM
(mono). If your FM Stereo
station is weak or you hear too
much noise or hissing, move
the BAND switch to the FM
position.
NOTE: FM Stereo Indicator illuminates
to show that you are listening
to FM stereo station.
6. LISTENING TO A COMPACT DISC
PLAYING A COMPACT DISC
This set is designed to play only compact
discs bearing this
identification logo
(logo must say DIGITAL AUDIO).
1. Set the FUNCTION Switch to CD
position. If a disc is in the compartment,
the Display will then show the total
number of tracks on the compact disc.
2. Press the CD PLAY/PAUSE Button to
start playback, and PLAY/PAUSE
indicator will be on steady, playback will
commence with the first track.
3. Adjust the VOLUME Control to the
desired volume level.
4. To pause playback, press the CD
PLAY/PAUSE Button, and PLAY/PAUSE
indicator will flash. To resume playback,
press the CD PLAY/PAUSE Button again,
and the lamp will change to steady on.
5. To stop the disc, press the CD STOP
Button, and PLAY/PAUSE indicator will
go off.
6. To turn off the CD, slide the FUNCTION
Switch to TAPE (POWER OFF) position.
NOTE: Never press the CD Door down
during play, this may cause malfunction or
damage the disc. Always stop the CD player
by using the CD STOP Button before you
take the disc out of the compartment.
If you hit or move the CD during play, the
music will stop for a second or two and then
start again. This is normal operation for
portable CD players.
6. When you finished programming, press
PLAY/PAUSE Button.
7. The Display will show the track number
being played, and the PROG indicator
will remain steadily on during program
play.
8. All songs will play in the order you
programmed.
9. If in middle of play you want to hear the
next programmed song, press SKIP UP
button.
10. When all the songs have finished, the
set will stop. The PROGRAM indicator
will remain on. To see the programme
sequence, press PROGRAM Button
once in CD stop mode.
11. To turn off the power, remember to slide
the FUNCTION Switch to TAPE
(POWER OFF) position.
NOTE: Programming can only be done
when the CD is stopped.
SKIPPING TRACKS (SEARCH)
1. This function enables you to find the
beginning of any desired track during
play. Press the SKIP UP button to select
the next track, press again repeatedly to
select subsequent tracks. The Display
will show the track number.
2. Press the SKIP DN button twice rapidly
to select the previous track. Repeated
presses of SKIP DN will select other
tracks
3. When the unit is in the pause mode, it is
also possible to select the beginning of a
certain track by using the SKIP UP button
and SKIP DN button to reach the desired
track. After selection, press CD
Play/Pause button.
4. Press and hold the SKIP UP button to
search forward at a high speed for a
particular section of a song. Press and
hold the SKIP DN button to search
backward. Release the button to resume
normal playback when the section is
found.
7. PROGRAM PLAY OPERATION
TO CLEAR THE CD MEMORY
Press CD STOP Button twice. The PROG
indicator will turn off and the Display will
show the number of tracks on the display.
8. REPEAT PLAY OPERATION
PROGRAMMED (MEMORY) PLAYBACK
(up to 20 tracks can be programmed)
1. Press PROGRAM Button during stop
mode.
2. "01" will flash in display and the PROG
indicator will flash.
3. Press the SKIP UP or SKIP DN Buttons
until the desired track shows on the
Display. The PROG indicator will flash.
4. Press PROGRAM Button. "02" will flash
in the display and the PROG indicator
will flash.
5. Repeat steps 3 and 4 until all the desired
tracks are programmed.
REPEAT PLAY SINGLE SONG
x1
x2
1. When the CD is stopped, press the SKIP
UP/DN Buttons to select the song you
like.
2. Press the REPEAT Button. The REPEAT
indicator will flash in the display.
3. Press PLAY Button. The song selected
will play over and over until the STOP
Button is pressed.
4. To cancel the Repeat Function, press
REPEAT Button twice and the REPEAT
indicator will turn off.
REPEAT PLAY ALL SONGS
To repeat ALL SONGS on a disc and play
them again and again.
1. Press REPEAT Button twice.
2. The REPEAT indicator will be on steady
(not flashing).
3. Press PLAY Button.
All the songs on the CD will play in order
and then start all over again.
4. To end the Repeat Function, press
REPEAT Button once.
5. To stop play, press STOP Button.
TO PLAY A CASSETTE TAPE
x2
x1
9. RANDOM PLAY OPERATION
Press the Random button once, the unit will
playback the disc in a random order. After all
the tracks are played the unit will stop
automatically.
In CD stop mode, you have to press the
play/pause button after pressing the
random button to begin random playback.
Press the Random button again to cancel
this play model.
10. CASSETTES
1. Open the Cassette Door by pressing the
Cassette STOP/EJECT Button (in some
cases, you may have to press the
Cassette STOP/EJECT Button twice
since this button has combined functions
of stop and eject.)
2. Insert the cassette, with the exposed
tape facing upwards, into the tracks in
the Cassette Door - the full reel or spool
should be on the right side.
3. Close the Cassette Door.
4. Check the position of the FUNCTION
Switch to make sure it is in the TAPE
position.
5. Press the Cassette PLAY Button.
6. Adjust the VOLUME Control to your
listening taste.
7. To stop the tape manually, press the
Cassette STOP/EJECT Button.
8. To remove the cassette, press the
Cassette STOP/EJECT Button again
and the Cassette Door will open.
Unload the cassette tape, flip it and return to
cassette compartment if you want to play
the other side of the cassette tape.
NOTE: If the PLAY Button pops up, the
tape has reached the end.
Remove the tape, flip it to the
other side and re-insert and press
PLAY Button.
CASSETTE TAPE SELECTION
AUTOMATIC LEVEL CONTROL (ALC)
The quality and condition of the cassette tapes you use will have a direct effect on the
performance of the cassette tape player.
Low quality tapes tend to break and stretch and a broken tape can easily become entangle
in the drive mechanism, causing major damage. Stretched tapes will run at uneven speeds
and will distort anything recorded on them.
h Use only well-known brands of tapes.
h Use of C-120 (120 minutes) cassette is not recommended. The extreme thinness of
this tape may result in breakage or other failures.
h This set is not designed for CrO2, Fe-Cr or METAL tape use. Therefore, be sure to use
named brand normal cassette tapes.
This product utilizes the latest Automatic
Level Control circuitry, therefore, it is not
necessary to adjust the Volume Control
when recording. This circuit automatically
records at the correct level and prevents
over loading.
NOTE: While recording you may adjust
the Volume Control as desired
without affecting the recording
operation.
11. RECORDING FROM RADIO/MICROPHONE/CD
RECORDING FROM RADIO
1. Follow the instructions TO PLAY THE
RADIO (slide the FUNCTION Switch to
RADIO position.)
2. Load the cassette tape into the Cassette
Door (full reel on the right side).
3. Tune into the station you want to record,
press the Cassette RECORD Button and
Cassette PLAY Button both at the same
time. Both buttons should remain when
released.
4. The recording process will automatically
stop at the end of the tape.
5. To stop the recording manually, press the
Cassette STOP/EJECT Button.
6. When you want to play the cassette tape
after recording, slide the FUNCTION
switch to TAPE position, press Cassette
REWIND Button, then press the
Cassette PLAY Button. Adjust the
VOLUME Control to your taste.
RECORDING FROM THE BUILT-IN
MICROPHONE
1. Load the cassette tape into the Cassette
Door (full reel or spool on right side).
2. Check the position of the FUNCTION
Switch to make sure it is in the TAPE
position.
3. Press the Cassette RECORD Button
and Cassette PLAY Button at the same
time. Both buttons should remain in their
down positions when released.
4. When you talk in front of the set, your
voice will be recorded. The recording
process will automatically stop at the end
of the tape and shut itself off.
5. To stop the recording manually, press the
Cassette STOP/EJECT Button.
6. To hear what you recorded, press the
Cassette REWIND Button then press the
Cassette PLAY Button.
RECORDING FROM A CD
1. Load the cassette tape into the Cassette
Door (full reel on the right).
2. Load the compact disc and close the CD
Door.
3. Set the FUNCTION Switch to CD
position.
4. Press the Cassette PAUSE Button for
the cassette.
5. Press the Cassette RECORD and PLAY
Buttons for record stand-by.
NOTE: When pressing the Cassette
RECORD Button, the
Cassette PLAY Button will
automatically go down. (If the
buttons do not go down,
reverse the tape or check
record prevention tab.)
6. Start the CD playing by pressing the
CD PLAY/PAUSE Button.
7. Press the Cassette PAUSE Button
when you wish to start recording.
8. Press the Cassette STOP/EJECT
Button to stop the recording.
9. To hear what you recorded, slide the
FUNCTION switch to TAPE position,
press REWIND Button and PLAY
Button.
13. PRODUCT SPECIFICATIONS
PICK-UP
System
Compact disc digital audio system
Laser diode
Properties
material: GaAIAs
Wavelength: =780nm
Emission Duration: continuous
Laser output: <44.6 W
Cross-interleave Reed-solomon code
Error correction
AUDIO
12. REMOTE CONTROL
REMOTE OPERATION
INSERTING BATTERIES
By using the remote controller, you can
operate the system in almost the same
way as with the controls of the main unit.
1. Open the battery compartment cover.
2. Install 2pcs UM-4 (size AAA) batteries
into the battery Compartment matching
the polarity as shown in the battery
compartment.
3. Close the battery compartment lid.
NOTE: Always remove batteries if the
remote controller is not going to
be used for a month or more.
Batteries left in the unit may
leak and cause damage.
REMOTE CONTROL RANGE
Use the remote control within an angle of
o
30 at the left and right horizontally and
over distances up to about 3 meters.
D/A conversion
Frequency response
1-bit DAC 8 times oversampling
Wow and flutter
No. of channels
Output level
Below measurable limits
2 channels (stereo)
Earphone: 20mW (32 )
Speakers Impedance
8
20-20,000Hz (+1/-3 dB)
3W*2
RADIO
Receiving bands
MW/FM
Frequency range
MW
FM
522-1620 KHz
87.5 -108.0 MHz
GENERAL
Power requirements
AC 230V/50Hz
DC 8* "C" size (or equivalents) batteries
Power consumption
13W
Approx. 319(L) X 261.7(W) X 123.3(H) mm
Approx. 2.244Kg (not including batteries)
Dimension
Net Weight
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement