American Sniper 80-3500

American Sniper 80-3500
Limited Warranty
American Sniper warrants new equipment against defects in material and workmanship under
normal use and service to the original purchaser. Any statutory implied warranties, including
any warranty of merchantability or fitness for a particular purpose, are expressly limited to the
duration of this written warranty. American Sniper will not be liable for any other damages,
including but not limited to indirect or special consequential damages arising out of or in
connection with the furnishing, performance, use or inability to use the machine. This remedy
shall be the exclusive remedy of the purchaser. The warranty period is subject to the conditions
stated below.
Safety, Operation and Maintenance
Manual with Parts List
Please read before use!
500 PSI Pump, Dual 3-Stage Motor
REGISTER
YOUR
MACHINE!
Lifetime on Molded Body Parts, 2-Years on Vacuum Motors,
1-Year on Pump and all Electrical Parts, 90-Days on Accessories
American Sniper warrants the roto-molded body to be free from defects in material and
workmanship, under normal use and service for a lifetime. American Sniper warrants the
motors to be free from defects in material and workmanship, under normal use and service
for two (2) years from the original date of sale. American Sniper warrants the pump and all
electrical components to be free from defects in material and workmanship, under normal
use and service for one (1) year. Parts replaced or repaired under this warranty are warranted
for the remainder of the original warranty period. Service labor charges are covered for one
(1) year from the date of purchase, when performed by a American Sniper-authorized service
provider.
230 Volt
All warranties exclude shipping expenses and all clients are responsible for all shipping
charges needed to complete warranty. Labor is only provided by authorized service centers.
If an authorized service center is not near you, it is the purchasers responsibility to take your
machine to an authorized service center.
Normal wear items such as capacitors, cords, finishes or switches will be warranted for
manufacturing defects for ninety (90) days from the purchase date.
All warranties of motors and associated components will be voided: if the machine is serviced
by anyone other than an authorized service provider; if the machine is mechanically modified;
if the machine is operated when not operating properly; or if the machine is misused or
abused all warranties are voided.
The warranty starts on the purchase date by the original purchaser from American Sniper
subject to proof of purchase. The Machine Registration Card must be completed and returned
immediately at the time of purchase. If proof of purchase cannot be identified, the warranty
start date is ninety (90) days after the inventory stocking date at the distributor’s warehouse.
12-Gallon Carpet Extractor With Heat
New Equipment Warranty
Reliable Power
Innovative Design
Safe & Easy to Use
Powerful Extracting
American Sniper
6 Reservoir Avenue, Greenacre SYDNEY NSW 2190 Australia
Phone: 1300 855 677 | Fax: 02 9796 3395
www.steamaster.com.au
Make a copy of this card for future reference.
Important Information and Safety Instructions
Register your Machine – Return your Warranty Registration Card.
Serial No:
© 2015 All Rights Reserved American Sniper
© 2015 Copy Rights Reserved American Sniper
Easy Transport
Patented Features
New Equipment Warranty
Lifetime warranty on roto-molded body, 2-years on vacuum motors, 1-year on 500 psi pump and all
electrical parts, 90-days on accessories and tools.
Warranty
Registration
Warranty Policy
All equipment is inspected and tested before shipping from the manufacturer. All parts are
warranted to be new and free from defects in workmanship and material, under normal use to the
original retail purchaser. This warranty limits manufacturer’s liability for defects in workmanship
or materials for replacement of defective parts only. The manufacturer accepts no liability for
incidental or consequential damages arisen from the use of any equipment, defective or not. This
warranty is in lieu of all expressed or implied warranties and is extended only to the original retail
purchaser. Manufacturer sales and service representatives are not authorized to waive or alter the
terms of this warranty, or to increase the obligations of the manufacturer under the warranty. Parts
replaced or repaired under this warranty are warranted for the remainder of the original warranty
period.
All warranties exclude shipping expenses and all clients are responsible for all shipping needed to
complete warranty. Labor is only provided by authorized service centers. If an authorized service
center is not near you, it is the purchasers responsibility to take your machine to an authorized
service center.
The manufacturer covers up to one (1) year (365 days) of service labor at the manufacturer’s
calculated hourly labor rate/repair time when performed by a manufacturer’s authorized service
provider. Ultimately, labor reimbursement costs are at the discretion of the manufacturer. At no time
is the manufacturer responsible for travel time to complete on-call repairs. After one (1) year, the
original retail purchaser is responsible for all labor costs with no manufacturer reimbursement.
The original purchaser must contact the manufacturer to follow correct RMA/warranty procedures.
They must have a copy of the RMA Sheet enclosed in the box with the returned item. No returns
shall be authorized unless the proper RMA procedures are followed. It is the responsibility of the
distributor to repair the client’s equipment as soon as possible.
The manufacturer charges a 25% restocking fee for any items that are being returned to stock.
Items must be new, unused, free of damage and are only good for up to 30 days. After 30 days, the
manufacturer does not accept the return of any item(s) for a store credit.
Authorized warranty replacement parts need to come directly from the manufacturer. Any use of
any other parts will void warranty. American Sniper does not reimburse for parts used by client that
were not supplied directly for the machine under warranty.
Please take a moment to register your machine online or fill
out the information below and mail back to American Sniper
immediately.
The warranty starts on the purchase date by the original purchaser subject
to proof of purchase. This Machine Registration Card must be completed
and returned immediately at the time of purchase. If proof of purchase
cannot be identified, the warranty start date is ninety (90) days after the
inventory stocking date at the distributor’s warehouse.
Machine ModelPurchase Date
Motor TypeSerial No.
Place of Purchase
Shipped To
Your NamePhone
Email Fax
Address Line 1
Address Line 2
CityStateZip
Comments:
The customer must contact the manufacturer prior to working on or changing out of any parts, etc.
The manufacturer must issue an RMA Sheet containing approved labor time and replacement parts.
Do not send parts or equipment back to the manufacturer without an RMA Number and approval.
No labor will be paid for, nor parts cost paid for or reimbursed, that have not previously been
approved by the manufacturer. All warranty work must be approved and authorized to qualify, and
appropriate warranty procedures must be followed.
The warranty starts on the purchase date by the original purchaser from an authorized American
Sniper distributor, subject to proof of purchase. The Machine Registration Form must be completed
and sent to the original manufacturer at the time of purchase. If proof of purchase cannot be
identified, the warranty start date is ninety (90) days after the date of sale to an authorized
American Sniper distributor.
Mail to:
6 Reservoir Avenue, Greenacre SYDNEY NSW 2190 Australia
See reverse side for warranty information.
Make a copy of this card for future reference.
© 2015 All Rights Reserved American Sniper
(2) 12-Gallon, 500 PSI Carpet Extractor
12-Gallon Carpet Extractor
By American Sniper
Please fill out the following information:
Model No:
Serial No:
Distributor Name:
Distributor Phone No:
Returned Material Authorization (RMA) Procedure
Original purchaser must contact the manufacturer to follow correct RMA/warranty
procedures. Must include a copy of RMA Sheet enclosed in the box with returned item.
No returns shall be authorized unless the proper RMA procedures are followed. It is the
responsibility of the distributor to repair the customer’s equipment as soon as possible. If
the distributor does not have the facilities to repair the equipment, it may be shipped or
taken to an authorized service center for repair.
Customer must contact the manufacturer prior to working on or changing out any
parts, etc. Manufacturer must issue an RMA Sheet containing approved labor time and
replacement parts. Do not send parts or equipment back to manufacturer without an RMA
Number and approval. No labor will be paid for, nor part costs paid for or reimbursed that
have not been previously approved by manufacturer. All warranty work must be approved
and authorized to qualify and appropriate warranty procedures must be followed.
1.0 Safety Instructions
Date of Purchase:
READ THIS MANUAL BEFORE USING YOUR CARPET EXTRACTOR.
KNOW THE PROPER OPERATION, CORRECT APPLICATIONS AND THE
LIMITATIONS OF THIS EQUIPMENT BEFORE USE.
Reduce the Risk of Fire, Electric Shock or Injury:
• Use only as described in this manual. Use only the attachments recommended by the
manufacturer.
• Test all outlets with an outlet tester before plugging machine into any outlet. Plug cord
into the nearest grounded outlet.
• DO NOT unplug by pulling on the cord, grasp the plug. DO NOT pull unit by the
cord.
• Keep cord away from heated surfaces.
• Never attempt adjustments or repairs while the machine is plugged in.
• DO NOT use if cord or plug are damaged.
• DO NOT use outdoors, in standing water on wet surfaces.
• Pay close attention when using machine near children.
• DO NOT pick up flammable or combustible materials or use machine where they may
be present.
• DO NOT leave machine outdoors, in extreme heat or cold. Harsh weather elements
will damage components and void warranty.
• Lift using only the appropriate handles.
American Sniper
6 Reservoir Avenue, Greenacre SYDNEY NSW 2190 Australia
Phone: 1300 855 677 | Fax: 02 9796 3395
www.steamaster.com.au
• Always wear the appropriate clothing and safety equipment when operating the
machine.
• Keep all body parts, hair and loose clothing away from openings and moving parts.
• Use extra care when cleaning stairs. Never move the machine up or down stairs with
fluid in the machine.
• Use common sense to protect yourself and others from injury when using the machine.
© 2015 Copy Rights Reserved American Sniper
12-Gallon, 500 PSI Carpet Extractor (3)
2.0 Set-Up / Prepare Unit for Use
9.0 Machine Parts List Continued
DO NOT USE ON WET SURFACES. DO NOT EXPOSE TO RAIN. STORE
INDOORS.
Item No.
Item Description
Qty. Drawing No.
10-0807Wheels for Extractor2
48
10-0834
Pump Flat Washer
18
49
10-0835-N
Nut for Pump Bolt on Extractor
8
50
10-0808Caster for Extractor2
51
10-0816
Caster Bolt 1/4-20 x 1/2 Hex Bolt
12
52
10-0843-COM
1/2” x 54” Clear Hose for Extractor Pump
Includes Fittings and Filter
1
53
80-0040-C
46” of Blue 3000 psi Hose for Extractor
Complete with Fittings and Clamps
1
54
80-0044-S
30” Black Hose with Fittings and Clamps
1
55
10-0835-N
Nut for Pump Bolt on Extractor
4
56
Hose FittingPart of 80-0044-S57
Hose FittingPart of 80-0040-C58
80-0015
500 psi Pump Mount Plate
1
59
10-0833
Motor Manifold Bolts for Extractor
4
60
80-0044-L
67” Black Hose with Fittings and Clamps
1
61
Hose FittingPart of 80-0044-L62
Hose FittingPart of 80-0044-S63
10-0881
1/4” MNPT x 3/8” JIC 90 Degree Part of 80-0044-S1
64
80-0016500 psi Pump1
65
10-0835-B
Pump Bolt for Extractor
4
66
80-0036Locking Plate1
67
10-0832S/R Strap Bolts4
68
10-0040
3000 psi Blue Hose - Part of 80-0040-C
6
69
80-0026
3/8” Barb x 1.4” MPT 90 Degree Part of 80-0040-C1
70
80-0017 Bulk Head fitting for Extractor 3
71
10-03798-32 x 3/8 Screw8
72
10-0868
1/4” Female QD for Extractor
1
74
10-0831S/R Bracket for Extractor2
75
80-0035
Bracket
1
Not Pictured
80-0037
RFI Filter
1
Not Pictured
80-0005-C
10 amp Circuit Breaker
1
Not Pictured
• All carpet extractors, no matter what the time of year, are shipped with antifreeze in
the solution lines. Prior to first use, fill the solution tank with one quart of warm water.
Attach the hose and using a hand tool or wand, flush out the system by spraying the
one quart of water through the pump.
• Attach the vacuum hose and the brass quick disconnect.
• Fill the solution tank with warm water (less than 100 degrees Fahrenheit). Fill to
approximately 4 inches from the top. Pre-spray and agitate the surface with detergent
made for floor cleaning or upholstery. Use only warm water to extract the pre-spray
from the surface.
• Be sure to replace any filters back into the machine prior to use.
• Do not use citric acid, butyl glycol or harsh degreasers inside the machine.
2.1
Electrical
2.2
Vacuum System
Plug cord(s) into 10 AMP grounded wall outlet(s). 10 AMP circuits are normally found in
kitchens and bathrooms. Never remove ground prong from the plug. If a circuit breaker
trips during operation, turn machine off, reset the breaker and move the electrical cord to
a different outlet and resume operation.
Automatic Vacuum Shut-Off: The float assembly shut-off, located in the recovery
tank on the vacuum stand pipe, prevents the waste tank from overflowing into the stand
pipe and damaging the vacuum motor(s). The float assembly will cut-off vacuum to the
waste tank. The motor(s) will also reach a fast, high-pitched sound alerting you when the
recovery tank is about to over flow. When this happens, immediately turn off the vacuum
motor(s) and empty the waste tank. If the operator continues to use machine after the tank
is full, it will void the Warranty.
The float assembly has a filter to prevent lint and debris from entering the stand pipe.
Refer to the “Maintenance” section for removal and proper cleaning.
Recovery Tank: the vacuum system requires the use of an external filter. The clear
view in-line filter is included with the machine and must be used on every job.
It is also necessary to use a defoamer to eliminate foam build-up in the recovery
tank which could lead to foam/moisture entering the vacuums and contributing to
early failure of the vacuum motors.
If moisture does enter the vacuum motors, contact an authorized service center. To
prevent moisture from damaging the vacuum motors during storage, empty the recovery
tank and store with the lid open.
(4) 12-Gallon, 500 PSI Carpet Extractor
12-Gallon, 500 PSI Carpet Extractor (13)
9.0 Machine Parts List
3.0 Grounding Instructions
Item No.
Item Description
Qty. Drawing No.
SN-12-ST-REDGRAN
12-Gallon Solution Tank – Red Granite
1
1
Part of Solution Tank
Insert Molded in to Solution Tank
2
80-0017Bulkhead Fitting for Extractor1
3
Part of 80-0017 Bulk Head Fitting
4
10-0846
1/4” MPT Hex Nipple for Extractor
1
5
10-08451/8” Strainer for Extractor2
6
80-0080-UN500 psi Regulator/Unloader1
7
80-0026
3/8 Barb x 1/4 MPT 90 Degree
3
8
10-0826
3/4” Hose Clamp for Extractor
5
9
80-0001
Extractor Exhaust Hose
0.4
10
80-0003-A
1-1/2” Black Lined Gray Hose
2
11
10-0806
1-1/2” Grey Hose Barb Fitting for Extractor
1
12
BracketPart of 80-0016 Pump1
13
80-000645 Degree Street Elbow1
14
80-001190 Degree Street Elbow1
15
10-0803
Splash-proof Switch for Extractor
3
16
80-0059500 psi Gauge1
17
80-0013500 psi Switch Plate1
18
ConnectorPart of 80-0059 Gauge19
SN-12-L-REDGRAN
12-Gallon Lid – Red Granite
1
20
80-00101/4” Brass Tee2
21
80-0011-290 Degree Street Elbow1
22
80-0004
1/4” x 4” Brass Nipple
1
23
10-0852
1/4” 90 Degree Brass Elbow
3
24
10-0804-A
Hatch Cover Gasket for Extractor
1
25
10-0804Hatch Cover for Extractor1
26
80-0012Float Assembly for Extractor1
27
10-0416-A
1-1/2” Black ABS Stand Pipe
1.3
28
80-00081.5 PVC Female Adapter1
29
SN-12-RT-BLKGRAN
12-Gallon Recovery Tank – Black Granite
1
30
10-0805Dump Valve for Extractor1
31
10-08491-1/2” ABS Fitting1
32
10-0155Hose Cuff Straight1
33
10-0848-B
1-1/2” 90 Degree ABS Street Elbow
3
34
10-0833
Motor Manifold Bolts for Extractor
6
35
80-0116Spacer for Motor Screw6
36
10-0810-A
230 Volt 3-Stage Extractor Motor
2
37
10-0838-A
Complete Pigtail for Extractor
1
38
10-0850
Strain Relief for Pigtail - Part of 10-0838-A
39
10-0851
Strain Relief Nut for Pigtail - Part of 10-0838-A
39
10-0822Exhaust Grate for Extractor3
40
10-1030-S3
3-Stage Extractor Motor Gasket
2
41
SN-12-MFLDExtractor Motor Manifold2
42
10-0830Hinge Keeper for Extractor2
43
10-0821Extractor Hinge2
44
10-0820
End Cap for Rod on Extractor
4
45
SN-12-MB-BLKGRAN
12-Gallon Motor Base – Black Granite
1
46
10-083619” Axle for Extractor1
47
10-0807Wheels for Extractor2
48
10-0834
Pump Flat Washer
18
49
10-0835-N
Nut for Pump Bolt on Extractor
8
50
10-0808Caster for Extractor2
51
10-0816
Caster Bolt 1/4-20 x 1/2 Hex Bolt
12
52
10-0843-COM
1/2” x 54” Clear Hose for Extractor Pump
Includes Fittings and Filter
1
53
DANGER: IMPROPER GROUNDING METHOD CAN RESULT IN A RISK OF
ELECTRIC SHOCK.
(12) 12-Gallon, 500 PSI Carpet Extractor
Electrical equipment must be grounded. If the machine should malfunction or breakdown,
grounding provides a path of least resistance for electrical current to reduce the risk
of electric shock. The plug must be inserted into an appropriate outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
If repair or replacement of the cord or plug is necessary, DO NOT connect the grounded
wire to a flat bed terminal. The grounding wire is the wire with insulation and an outer
green surface, with or without yellow stripes.
Grounding Method
This equipment is designed to run on 230V/50 HZ electrical power. Equipment includes
a grounded plug. A 10 amp circuit is required to operate machine. 10 amp circuits are
normally found in kitchens and bathrooms. If a circuit breaker trips during operation,
reset the breaker and move the electrical cord to a different outlet to resume operation.
WARNING:
Improper connection of the equipment grounding conductor can result in a risk of
electric shock. Check with a qualified electrician or service person if you are in doubt
as to whether the outlet is properly grounded. DO NOT modify the plug provided with
the equipment. If the plug will not fit into the outlet, have a proper outlet installed by a
qualified electrician.
This is machine is equipped with an
Australian 3-prong plug.
12-Gallon, 500 PSI Carpet Extractor (5)
4.0 Shutdown Procedures
• When finished cleaning, turn OFF all
switches.
8.0 Machine Schematic Drawing
• Disconnect the solution hose and vacuum
hose from the cleaning tool. Pull the valve
trigger to release pressure from the hose
before disconnecting the solution hose from
the cleaning tool.
• Disconnect the clear view in-line filter from
the vacuum hoses and clean the filter as
needed.
• Disconnect the vacuum hose and solution
hose from the machine.
• If water remains in the solution tank, use
the short vacuum hose and vacuum the
excess water from the tank (image 1).
• Disconnect the power cords from the outlets
and from the machine.
• Remove the float assembly from the
recovery tank and clean filter as needed.
Replace float assembly and tank lid
(image 2).
• Drain any remaining water from the recovery
tank and dispose of in a sanitary drain. DO
NOT use the same bucket to drain the tank
that you used to fill the tank (image 3).
• Roll up all hoses and tools. Collect and store
extractor, all tools and accessories.
(6) 12-Gallon, 500 PSI Carpet Extractor
12-Gallon, 500 PSI Carpet Extractor (11)
6.0 Storage and Freeze Protection Continued
Recommended Procedure for Storage Continued
• Attach and wands and hand tools that will also be stored with the Carpet Extractor.
Open the valve for 30 seconds, directing the spray to the solution tank. Disconnect the
hose and with the valve open and the jets pointing down, depress the dimple on the
male QD. This will drain the solution out of the tool. Drain thoroughly before storing.
• Turn off the pump and disconnect all hoses and tools. Vacuum out the solution tank
and thoroughly drain the recovery tank and vacuum hose.
To return to service, flush the pressure system by repeating the above steps, using
fresh water in place of antifreeze.
7.0 Trouble Shooting Guide
Never operate this Carpet Extractor when the equipment is not performing as expected
or when any part is visibly damaged. When repair is needed, take the equipment to an
authorized service center.
System
Problem
Possible Cause
Remedy
Vacuum
System
No Vacuum
/ Weak
Vacuum
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Vacuum Tank Full
Float Assembly Tank Screen Dirty
Float Ball Stuck
Damaged or Loose Vacuum Hose
Dump Valve Open
Access Lid not Sealed
Vacuum Hose Clogged
Air Intake Grid Clogged
Leak in Recovery Tank
Water Coming out of Vacuum Exhaust
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Empty Tank
Clean the Screen with Water
Tap Float to Unstick then Clean
Attach or Replace
Close Valve
Replace Gasket
Clear Debris
Clean
Clean and Dry Area, Patch with Silicone
Use a Low Foaming Detergent
1.
2.
3.
4.
Extension Cord not Plugged In
Switch not in the “On” Position
Building Circuit Overloaded
Wiring Connections Loose
1.
2.
3.
4.
Check if Machine and Cord are Plugged In
Check Switches, Replace if Necessary
Reset Circuit
Unplug Machine and Check for Loose
Wires
Burning
Smell
1.
2.
Vacuum Motor Hung Up
Pump Motor Hung Up
1.
2.
Replace Vacuum Motor
Replace Pump
Pump is not
Running
Properly
1.
2.
3.
4.
5.
6.
7.
1.
2.
3.
4.
5.
6.
7.
Check the Electrical System
Clean Jet Filters
Clean In-Line Filter
Clear Debris
Check and Replace Hoses if Necessary
Replace Pump
Snap Quick Disconnects Together\
8.
No Power to the Pump
Jets on Wand are Clogged
In-Line Water Filter is Clogged
Debris in Solution Tank Covering Inlet
Kinked or Loose Hose
Pump Failed
Quick Disconnects are not Completely
Locked Together
Heater is Clogged with Deposits
8.
9.
10.
Pump is Pulsating
Auto Prime Valve is Open
9.
10.
Flush Heater with System Maintainer or
Replace if Necessary
Check for Clogged Jets and Clean
Close Valve
Electrical
System
Pump
System
Unit will not
Turn On
(10) 12-Gallon, 500 PSI Carpet Extractor
5.0 Maintenance
Regular maintenance is required to keep your Carpet Extractor in proper working
condition. Failure to properly maintain your machine could void warranty. Thoroughly
clean all equipment and accessories after each use:
• Rinse the solution and recover tanks with clean water.
• Flush the pump system with clean water, including all hoses and wand(s).
• Do not allow water to remain in the tanks after use.
• Lubricate all quick disconnects with WD-40 or similar lubricant.
• Clean vacuum float assembly screen.
WARNING: Disconnect electrical power cord before performing any service or
maintenance inside the machine base or before testing or repairing switches or power
cords. Failure to do so may result in severe personal injury or death.
Operation
Clean Vacuum Assembly Screen
Rinse Out Recovery Tank
Flush Solution Tank and Pump
Clean Pump-Inlet Filter
Interval
Daily- After Each Job
Daily
Daily
Weekly - As Needed
5.1
Clean Fresh Water Tank Filter
5.2
Clean Vacuum Float Assembly Screen
The fresh water tank filter is located at the bottom of the solution tank. Unscrew the filter
counterclockwise and rinse with fresh water. If necessary, use a tooth brush to remove
detergent build-up. Note, a heavy build-up is a warning sign that the solution system
should be flushed. See the “Flush Chemical System” section.
Inside the recovery tank, on top of the stand pipe, is the vacuum float assembly. It
functions to prevent debris and water from being sucked into the vacuum motors.
Operating the Carpet Extractor without the float assembly or with a poorly maintained
assembly, will greatly decrease the life of the vacuum motors and will void the warranty.
If debris builds up on this filter, it will reduce the vacuum air flow and may cause a
significant decrease in the rate of water recovery. If debris prevents the float ball from
moving or seating inside the assembly, it may not stop the airflow when the tank fills with
water and the water will be sucked in the vacuums and blow out the exhaust.
To clean, twist off the float assembly from the stand pipe and clean the screen. Pull fibers
and lint off and rinse with clean water. Push the assembly back onto the stand pipe and
replace the recovery tank lid.
12-Gallon, 500 PSI Carpet Extractor (7)
5.2
Clean Vacuum Float Assembly Screen Continued
5.3
Rinse Out Recovery Tank
This screen should be cleaned frequently if
the Carpet Extractor is being operated in an
environment which has an abnormal buildup of lint and debris, such as cleaning newly
installed carpet. Loss of vacuum is most
normally associated with lint build-up in this
filter at the top of the vacuum stand pipe.
5.4
Clean Pump Inlet Filter Continued
Build-up of fine silt and debris can damage the
Vacuum Float Assembly
auto-dump pump and dump valve. Clean out
the recovery tank on a regular basis to extend the
life of these components as well as keep the tank and machine smelling better.
To rinse out recovery tank, remove the recovery tank lid and open the dump valve. Place
a bucket under the dump valve. Use a hose to rinse the dirt and debris out of the recovery
tank. Close the dump valve and spray the tank with deodorizer or disinfectant. Proceed to
waste pump cleaning and replace the recovery tank lid. Dispose of dirty water and debris.
1/4” Acorn Strainer
Part No. 10-0845
5.5
WD-40 Vacuum Motors
Should moisture ever enter the vacuum motors, completely drain the recovery tank,
open the recovery tank lid, remove the vacuum float assembly, turn on both vacuum
motors and spray a five (5) second burst of WD-40 into the standpipe. Continue to
run the vacuum motors for at least three (3) minutes.
To prevent moisture from damaging the vacuum motors during storage, empty the
recovery tank and store with the lid open.
6.0 Storage and Freeze Protection
You must winterize your Carpet Extractor to protect the pump system from freezing
and also damage being caused to fittings and valves. Damage due to freezing is not
covered under the Warranty. Store your extractor in temperatures over 40 degrees
Fahrenheit. If you plan on storing your extractor in freezing conditions or for a long
period of time, the following procedure should help prevent your Carpet Extractor
from freezing and prevent pump and seals from drying out.
5.4
Clean Pump Inlet Filter
CAUTION: before proceeding with this procedure, make sure both the power cords are
disconnected.
• To examine the filter, open the solution tank lid on the front of the machine. The filter
is in the bottom of the solution tank.
• Grasp the filter cap and unscrew the filter from the brass nipple by turning counterclockwise. Clean or replace the filter as needed.
• Tilt the tanks back onto the base and secure the plate.
(8) 12-Gallon, 500 PSI Carpet Extractor
Recommended Procedure for Storage
• In a separate container, mix 1/2-gallon of water with 1/2-gallon of RV Water
System Antifreeze. Mix well and pour into the solution tank.
• Connect the pressure hose to the female quick disconnect (QD) on the front of
the machine. Insert an open-ended male QD into the female QD on the end of the
pressure hose.
• When primed, turn down the pressure to 100 PSI.
• Disconnect the open-ended QD and connect the solution hose to the male QD at
the auto-fill/chemical feed connection. CAUTION: applying high pressure (over
100 PSI) to the chemical feed system will damage the mechanism.
12-Gallon, 500 PSI Carpet Extractor (9)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement