FMX D11 66 Tractor all wheel drive B

FMX D11 66 Tractor all wheel drive B
Volvo Trucks. Driving Progress
FMX D11 66 Tractor all wheel drive B-ride FM 66 T1CBX
3191
,264
Cab 2490
Chassis Dimensions [mm]
WB Wheelbase
3600
3700
3900
A
D
Overall Chassis Length
Center of rear axle to back of cab
7295
2604
7395
2704
7595
2904
T
Theoretical Wheelbase
4285
4385
4585
5225
4170
9395
5230
4170
9400
5245
4205
9450
Chassis Weights [kg]
Front Axle
Rear Bogie
Kerb Weight
Turning Diameter [mm]
Turning Circle Diameter Kerb to Kerb
Turning Circle Diameter Wall to Wall
15200 15500 16100
16600 16900 17600
Plated Weights [kg]
Design
Gross Vehicle Weight
Gross Combination Weight
Front Axle
Rear Bogie
29000
60000
8000
21000
Important Notes
Chassis Dimensions
Cab Height: +416 mm for CAB-HSLP.
Front Axle to Back of Cab: -424 mm for CAB-DAY.
D-measure includes a front clearance of 50 mm and for rigid trucks also a
subframe of 100 mm.
Height can vary ± 20 mm for leaf and ± 10 mm for air suspension.
All dimensions are for unladen chassis and any tag axles down.
Weight and dimensions are based upon the following tyres:
Front Axle Tyres:
315/80R22.5
Drive Axle Tyres:
315/80R22.5
Chassis weight includes oil, water, AdBlue, 70 litres fuel and without
driver. Kerb weight can vary ± 3%.
Turning diameters are theoretically calculated.
Legal weights can differ from country to country.
For more detailed weight information, including optional equipment weights,
ask your Volvo sales contact to enter your specification into the Volvo Weight
Information system (WIS).
Do NOT use this drawing for bodybuilding. Refer to Volvo Bodybuilder
Instructions and chassis assembly drawing FM66T1CBX.
1 (6)
Ref: FM 66 T1CBX01 8EE 2016-09-08 ENGVT
FMX D11 66 Tractor all wheel drive B-ride FM 66 T1CBX
□ AUDHIG
Transport operation
■ RC-ROUGH
Rough road conditions.
• Less than 95% of the driven distance on well maintained or
less maintained surfaced roads.
and / or
• In total not more than 5% of the driven distance on:
- Very badly maintained surfaced roads.
- Hard packed sand or gravel surface of very bad quality.
- Washboards.
- Soft unpaved surface.
- Off-road.
■ CHH-XXHI
Chassis height extra high - approx. 1150 mm above ground
level
■ RADD-BR
Rear leaf suspension, 2 axles - 2 driven (B-ride)
□ FMX-DAY
□ FMX-HSLP
■ FMX-SLP
FMX Day cab
FMX Globetrotter sleeper cab
FMX Sleeper cab
■ EU3
□ EU4SCR
□ EU5EEV
Euro 3 engine emission level
Euro 4 emission level with Selective Catalytic Reduction (SCR)
Emission level Euro 5, Enhanced Environmental friendly
Vehicle (EEV)
Euro 5 emission level with Selective Catalytic Reduction (SCR)
Euro 6 emission level with Selective Catalytic Reduction
(SCR), particulate filter and Exhaust Gas Recirculation (EGR)
■
□
□
□
□
□
□
□
D11A330
D11A370
D11A430
D11C330
D11C370
D11C410
D11C450
D11K330
□ D11K370
□ D11K410
□ D11K450
□ EBR-EPG
□ EBR-EPGC
□ EBR-VEB
■ AT2612F
□ PT2106
□ VT2214B
□ VT2514B
□ VTO2214B
□ VTO2514B
■ RTH2610F
□ MEDIADF
□ MEDIANAV
□ MEDIANDF
Core components
□ EU5SCR-M
□ EU6SCR
□ MEDIA
Diesel engine, 10.8 litre Euro 3, 330 hp, 1650 Nm
Diesel engine, 10.8 litre Euro 3, 370 hp, 1770 Nm
Diesel engine, 10.8 litre Euro 3, 430 hp, 1970 Nm
Diesel engine, 10.8 litre Euro 4/5 SCR, 330 hp, 1600 Nm
Diesel engine, 10.8 litre Euro 4/5 SCR, 370 hp, 1750 Nm
Diesel engine, 10.8 litre Euro 4/5 SCR, 410 hp, 1950 Nm
Diesel engine, 10.8 litre Euro 4/5 SCR, 450 hp, 2150 Nm
Diesel engine, 10.8 litre Euro 6 SCR + EGR (Diesel particulate
filter), 330 hp, 1600 Nm
Diesel engine, 10.8 litre Euro 6 SCR + EGR (Diesel particulate
filter), 370 hp, 1750 Nm
Diesel engine, 10.8 litre Euro 6 SCR + EGR (Diesel Particulate
Filter), 410 hp, 1950 Nm
Diesel engine, 10.8 litre Euro 6 SCR + EGR (Diesel Particulate
Filter), 450 hp, 2150 Nm
Engine brake with exhaust pressure governor, EPG
Volvo engine compression brake with exhaust pressure
governor, EPG (for I-shift)
Volvo Engine Brake, VEB (compression brake with exhaust
pressure governor, EPG)
I-Shift automated mechanical 12-speed gearbox without clutch
pedal, max. engine torque 2600 Nm, max. permitted GCW
100000 kg.
Powertronic automatic 6-speed gearbox, max. engine torque
2100 Nm, max. permitted GCW 100000 kg
Manual range & splitter 14-speed gearbox, max. engine torque
2400 Nm, max. permitted GCW 100000 kg
Manual range & splitter 14-speed gearbox, max. engine torque
2500 Nm, max. permitted GCW 100000 kg
Manual range & splitter 14-speed overdrive gearbox, max.
engine torque 2400 Nm, max. permitted GCW 100000 kg
Manual range & splitter 14-speed overdrive gearbox, max.
engine torque 2500 Nm, max. permitted GCW 100000 kg
Rear hub reduction tandem axles - bogie load 26 tonnes, GCW
100 tonnes
Packages
□ OFFRFMXS
High power audio system. RDS radio with CD player (also
playing mp3/wma/wav files from CD), FM/AM antenna,
speakers in dashboard & doors & sleeping compartment,
integrated bluetooth phone and USB/Line inputs.
Prepared for Dynafleet office internet portal support.
Media package with infotainment. Prepared for Dynafleet office
internet portal support.
Media package with infotainment. Prepared for both Dynafleet
vehicle onboard support and for Dynafleet office internet portal
support.
Media package with infotainment. Prepared for both Navigation
support and for Dynafleet office internet portal support.
Media package with infotainment. Prepared for both Navigation
support, Dynafleet vehicle onboard support and for Dynafleet
office internet portal support.
Construction package for FMX sleeper cabs
Chassis
■ FST-PAR3
3 leaf front parabolic suspension (stiffer than normal)
□ FAL10.0
■ FAL8.0
□ FAL9.0
Front axle load 10.0 tonnes
Front axle load 8.0 tonnes
Front axle load 9.0 tonnes
■ FSTAB
Front stabilizer with normal stiffness
■ RAL21
Rear axles load 21 tonnes
■ PSP-FIX
□ PSP-VAR
Power steering pump with fixed displacement
Power steering pump with variable displacement
■ RST-PAR1
Rear parabolic leaf suspension with normal stiffness
□ FBREG-RP
Front axle regulating brake valve with reduced pressure / low
pressure range
■ FRAME300
Frame rail section external height 300 mm
■ FST7070
□ FST8080
Frame section thickness - web 7.0 mm / flange 7.0 mm
Frame section thickness - web 8.0 mm / flange 8.0 mm
□ FIL-EEEB
■ FIL-TXEB
Frame inner liner from end of engine end to end of bogie
Frame inner liner from transmission cross member to end of
bogie
■ BBOX-L
Battery box on left hand side
■ 2BATT170
□ 2BATT225
Batteries 2x170 Ah
Batteries 2x225 Ah
■ BATTAMP
□ BATTIND
Battery voltage and ampere gauge
Battery voltage, ampere and battery status gauge with visual
alerts
■ MSWI-C
Chassis main switch - battery box placed toggle switch citcuit
shut down
Remote controlled main switch - remote controlled (key fob)
circuit shut down
□ MSWI-R
■ R315A56
Right 315 litre aluminium 560 mm high D-shaped diesel tank.
Usable volume is 97% of stated volume.
Min volume 255l
Max volume 630l
□ ADTP-BC
□ ADTP-L
□ ADTP-R
AdBlue tank behind/under cab on right hand side
AdBlue tank on left hand side (for dual front axles between the
axles)
AdBlue tank on right hand side
□
□
□
□
□
AdBlue tank usable volume 48 litres
AdBlue tank usable volume 50 litres
AdBlue tank usable volume 64 litres
AdBlue tank usable volume 68 litres
AdBlue tank usable volume 90 litres
ADB048
ADB050
ADB064
ADB068
ADB090
□ DRIVEFM
□ DRIVEFM+
Driving package FM
Driving plus package FM
■ FCAP-L
Lockable diesel and AdBlue tank caps
□ 1BEDARFM
□ 1BEDFM
1 Bed resting package arctic FM
1 Bed resting package FM
■ FUFF-AS
□ FUFF-ATS
Fuel filling anti-spillage device
Fuel filling anti-theft and anti-spillage devices
■ AUDBAS
Audio basic. RDS radio with CD player, FM/AM antenna and
speakers in dashboard&doors.
Prepared for Dynafleet office internet portal support.
■ ESH-REAR
□ ESH-VERT
□ ESV-VERT
Horizontal muffler, rear exhaust outlet
Horizontal muffler, vertical exhaust outlet on right hand side
Vertical muffler, vertical exhaust outlet on right hand side
■ Standard Equipment
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
2 (6)
Ref: FM 66 T1CBX01 8EE 2016-09-08 ENGVT
FMX D11 66 Tractor all wheel drive B-ride FM 66 T1CBX
■ TOOL-BAS
□ TOOLKIT
Basic tools (combination screw driver, socket wrench)
Extended tool kit
□ INFLAHOS
Tyre inflation hose (18 metres)
□ GAUGE-TP
Tyre pressure gauge
Wheel chock(s) in the front part of the vehicle.
- TRACTOR, BBOX-L, Fold, 1/2 w chocks
= Top of
left side battery box
- TRACTOR, BBOX-EF, Fold, 1/2 w chocks
= Top of
lefts side fuel tank
- TRACTOR, BBOX-EF, Fix, 2 w chocks
= Left
frame front of fuel tank
- RIGID, 1 front axle, Fold, 1/2 w chocks
= Top of left
side battery box
- RIGID, 2 front axles, Fold, Frame free space, 2 wc = Top of
left side battery box
- RIGID, 2 front axles, Fix, W/o frame free space,2 wc = Left
frame behind 1st front wheel
Wheel chock(s) in the middle part of the vehicle
- TRACTOR, BBOX-L, Fix, 1/2 w chocks
= Left frame front
of rear wheels
- RIGID, 1 front axle, Fix, 1/2 w chocks = Left frame front of
(or behind) rear wheels
Transport mounted wheel chock(s) in cab outer luggage
compartment
□ OBDEP-C
EU6 mandatory on board diagnostics, phase C regulations
□ TB-L80
Left toolbox 800 mm length (mounting length 800 mm, real
length 730 mm)
□ AMSO-AUT
I-shift manual gear shift available in automatic mode incl
kickdown function
□ TB-R80
Right toolbox 800 mm length (mounting length 800 mm, real
length 730 mm)
□ AVO-ENH
Enhanced I-shift software for construction and off road
applications
□ CHAIN-S
Snow chains
□ APF-ENH
□ HOOK-SC
Snow chain hooks.
Rear mounted for tractors and side mounted in rear overhang
for rigids. Two hooks on each side.
Enhanced I-shift PTO functions (Auto Neutral / Reverse Inhibit
/ Split Box Connection)
□ CD40B-O
■ CS43B-O
Double plate clutch, plate diameter 400 mm
Single plate clutch, plate diameter 430 mm
■ TOWF-HD1
One heavy duty front towing device
□ RET-TPT
Retarder for hydraulic gearbox
■ RFEC-B
Rear frame end, bent (standard for tractor vehicles)
□ TOWR-ONE
One rear towing device in frame end cross member
□ TC-HWO
□ TC-MAOH2
□ TREL15
□ TREL7
■ TREL7-7
15 pol electrical trailer connector (ADR certified)
7 pol electrical trailer connector (24N)
2x7 pol (24N+24S) electrical trailer connectors (UADR)
■ TBC-EC
Trailer brake connection, European Community
Cooler for hydraulic gearboxes - water/oil
Extra high performance cooler for manual/I-shift gearboxes air/oil
Basic performance cooler for manual/I-Shift gearboxes water/oil
High performance cooler for manual/I-Shift gearboxes water/oil
□ TRBR-HCF
□ TRBR-HCR
□ TRBR-STA
Full pressure hand controlled trailer brake (8 bar)
Reduced pressure hand controlled trailer brake (4 bar)
Stationary trailer brake control
□ RFEND-B
Rear 3 piece fenders with anti-spray function (all rear axles)
□ RFH-BAS
Optimal fender installation (rear and 2nd front axle) with regard
to legal demands, wheel/tyre sizes, chassis height and fifth
wheel height.
Highest fender installation (rear and 2nd front axle).
Suitable for rough and very rough road conditions.
Lower fender installation (rear and 2nd front axle).
Suitable only for smooth road conditions.
□ EXST-SSP
□ EXST-ST
Bright polished vertical stainless steel exhaust top pipe
Aluminized steel vertical exhaust top pipe
□ WHC-FIX2
□ WHC-FOL2
Two fixed wheel chocks
2 foldable wheel chocks
□ WHCP-F
□ WHCP-M
□ WHCP-T
□ RFH-HIG
□ RFH-LOW
□ TL-LED
LED tail lamps
□ BLIGHT-E
Emergency brake light
Rims and Tyres
Powertrain equipment
□ TRAP-HD
Reinforced gearbox application.
For manual gearboxes a heavy-duty nodular iron range
housing.
For I-shift gearboxes (2412 excl.) a reinforced gear shifting
system.
□ PVT-BAS
□ PVT-EXT
Basic topography information, learning by GPS positioning
Extended topography information, learning by GPS positioning
and centrally stored data
□
□
□
□
□
I-shift City gear changing software
I-shift construction gear changing software
I-shift distribution gear changing software
I-shift Heavy Duty gear changing software
I-shift Heavy Duty & Fuel Economy+ gear changing software
prepared for using GPS positioning (centrally stored road
memory, I-See)
I-shift long haul gear changing software
TP-BAS
TP-CON
TP-DIST
TP-HD
TP-HD3
□ TP-LONG
□ TC-MWO
□ TC-MWOH2
□
□
□
■
1COMP530
2COM1080
2COM1100
2COMP900
Single cylinder air compressor 318 cc / 530 l/min
Dual cylinder air compressor 704 cc / 1080 l/min
Dual cylinder air compressor 760 cc / 1100 l/min
Dual cylinder air compressor 636 cc
□ CLU-AIRC
Air compressor clutch automatically declutched when not
needed in order to save fuel
■ AIRIN-HI
□ AIRIN-LO
High air intake
Low air intake
□ ACL1ST-S
Air cleaner with additional filter element (primary + secondary)
■ 24AL110B
□ 24AL120B
□ 24AL150B
Alternator 110 Ampere
Alternator 120 Ampere
Alternator 150 Ampere
□ CCV-C
■ CCV-O
□ CCV-OX
Closed crankcase ventilation
Open crankcase ventilation
Closed crankcase ventilation with oil separator and a
maintenance free gas centrifuge
■ RT-STEEL
Steel rims on all axles
□ SPWT-D
□ SPWT-F
Spare wheel with tyre equal to drive
Spare wheel with tyre equal to front wheel
□ PRIM-EL
■ PRIM-MAN
Electrical priming pump
Manual priming pump
□ SWCP-T
Temporary spare wheel carrier.
Spare wheel is transport mounted (strapped on top of the
frame rails) with plastic stips.
Spare wheel carrier transport mounted with the spare wheel on
top of the frame rails
□ FUEQ-EH
Fuel line electric heater
■ AF-E
□ AF-R
Electrically heated fuel filter
Hot fuel recirculation heated fuel filter
■ EST-AID
Engine start pre-heating element
Jack 20 tonnes
□ 220EBH15
Engine block heater, 220 volt, 1.5 kW
□ SWCP-TP
□ JACK-20T
■ Standard Equipment
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
3 (6)
Ref: FM 66 T1CBX01 8EE 2016-09-08 ENGVT
FMX D11 66 Tractor all wheel drive B-ride FM 66 T1CBX
□ PTER-100
□ PTER-DIN
□ PTER1400
□ HPE-F101
□ HPE-F41
□ HPE-F51
□ HPE-F61
□ HPE-F81
□ HPE-T53
□ HPE-T70
□ HPE-V45
□ HPE-V75
□ PTPT-D
□ PTPT-F
□ PTR-D
□ PTR-DH
□ PTR-DM
□ PTR-F
□ PTRD-D
□ PTRD-D1
□ PTRD-D2
□ HPG-F101
□ HPG-F41
□ HPG-F51
□ HPG-F61
□ HPG-F81
□ EIDLESD
Rear engine mounted clutch independent power-take-off with
flange connection (DIN 100 / ISO 7646)
Rear engine mounted clutch independent PTO with splined
shaft groove (female) for a close coupled pump (DIN 5462 /
ISO 7653)
Rear engine mounted clutch independent power-take-off with
flange connection (SAE 1410 / ISO 7647)
Rear engine mounted hydraulic pump F1-101, fixed
displacement, single flow
Rear engine mounted hydraulic pump F1-41, fixed
displacement, single flow
Rear engine mounted hydraulic pump F1-51, fixed
displacement, single flow
Rear engine mounted hydraulic pump F1-61, fixed
displacement, single flow
Rear engine mounted hydraulic pump F1-81, fixed
displacement, single flow
Rear engine mounted hydraulic pump F2-53/53, fixed
displacement, twin flow
Rear engine mounted hydraulic pump F2-70/35, fixed
displacement, twin flow
Rear engine mounted hydraulic pump VP1-45, variable
displacement, single flow
Rear engine mounted hydraulic pump VP1-75, variable
displacement, single flow
Automatic gearbox driven power take-off, 1 front/upper
connection (DIN 5462 / ISO 7653) for plug-in pump (max. 850
Nm).
Automatic gearbox driven Power take-off, 1 front/upper rear
facing flange connection (SAE 1410 / ISO 7647) for propeller
shaft (max. 850 Nm).
Mechanical gearbox driven low speed power take-off, 1 rear
connection (DIN 5462 / ISO 7653) for plug-in pump (max. 1000
Nm).
Mechanical gearbox driven high speed power take-off, 1 rear
connection (DIN 5462 / ISO 7653) for plug-in pump (max. 600
Nm).
Mechanical gearbox driven medium speed power take-off, 1
rear connection (DIN 5462 / ISO 7653) for plug-in pump (max.
600 Nm).
Mechanical gearbox driven low speed power take-off, 1 rear
flange connection (SAE 1410 / ISO 7647) for propeller shaft
(max. 1000 Nm).
Mechanical gearbox driven high speed power take-off, 1 rear
and 1 front connections (DIN 5462 / ISO 7653) for plug-in
pumps (max. 870 Nm).
Mechanical gearbox driven high speed power take-off, 1 rear
flange connection (SAE 1410 / ISO 7647) for propeller shaft / 1
front connection (DIN 5462 / ISO 7653) for plug-in pump (max.
870 Nm).
Mechanical gearbox driven power take-off, 2 rear flange (highlow speed) connections (SAE 1310/1410 / ISO 7647) for
propeller shafts / 1 front (high speed) connection (DIN 5462 /
ISO 7653) for plug-in pump (max. 870/1000 Nm).
Gearbox mounted hydraulic pump F1-101, fixed displacement,
single flow
Gearbox mounted hydraulic pump F1-41, fixed displacement,
single flow
Gearbox mounted hydraulic pump F1-51, fixed displacement,
single flow
Gearbox mounted hydraulic pump F1-61, fixed displacement,
single flow
Gearbox mounted hydraulic pump F1-81, fixed displacement,
single flow
Engine idle shut down
Airbag on driver side
□ INST-BAS
Basic level instrument cluster - 4 inch monochrome display
240x320 pix
□
■
□
□
One day analogue tachograph, basic
One day digital tachograph, EC approved
One day analogue tachograph, EC-approved
Seven day analogue tachograph, basic
1DAYB
1DAYDIG
1DAYEC
7DAYB
□ ARSL
Additional road speed limiter (switch in dashboard)
□ CRUIS-E
■ CRUISEC
Cruise control I-Cruise with controls in the steering wheel,I-Roll
incl. Adding PVT-EXT gives I-See.
Basic cruise control with controls in steering wheel
□ RSENS-W
Wiper rain sensor
□ CU-ECC
■ CU-MCC
Fully electrically controlled air conditioning with sun sensor
Electrical manually controlled air conditioning
□ IMMOBIL
Immobiliser
□ ALARM-B
□ ALARM-E
Burglar alarm - cab
Burglar alarm - cab/body/trailer
□ ALCOLOCK
Alcolock
□ PHONE-PK
Telephone preparation kit (antenna, antenna attachm. and
cable incl.)
■ WLIFT-EB
□ WLIFT-ME
Electrical window lift
Mechanical window lift
■ ISUNS-DS
Side interior sun visor on driver side
■ ISUNF-B
□ ISUNF-MD
Interior front sun visor without mirror
Interior front sun visor with mirror on driver side
■ CSPU-S
One open storage (behind push open lid) in upper part of dash
panel center section
□ BUPALARM
Back-up alarm
□ BUPMON
Back-up monitor including a 7 inch colour display integrated in
dashboard, Waeco CCD-camera (delivered loose in cab) with
a heated lens, motorised lens protection, 1 m pigtail cable
(front) and 10 metres chassis cable for tractor /20 metres for
rigid. Camera wirings not installed. Use PCA30081 for
installation.
□ RTOLL-PK
Preparation kit for road toll collect (GPS/GSM antenna and
cables)
□ REMC-MF
Wireless remote control - multi functional
□ FIREXT3S
Fire extinguisher 3 kg, Swedish/English decal
□ WARNVEST
Warning vest
□ AIDKIT
First aid kit containing sticking plaster, washing and drying
pads, compresses, elastic bandages, respiratory mask, gloves
and scissors
First aid kit containing sticking plaster, compresses, elastic
bandages, gloves, scissors, triangular bandage, bandaging
cloths, adhesive tape and rescue sheet (German
requirements)
□ AIDKIT1B
□ WARNLAMP Portable warning lamp with batteries
□ LAMP-IN
Inspection lamp
□ BULBKIT
Bulb and fuse kit
□ WRITEPAD
Writing pad
Cab Interior, Living
□ UPHTRI10
Cab Interior, Driving
□ DRC-AMII
□ AIRBAG
■ DRC-AUTO
Regeneration control of diesel filter particulates - auto initiation
/ manual on demand / manual inhibition
Regeneration control of diesel filter particulates - fully
automatic (in motion)
□ STWM-LE
Leather steering wheel
■ UPHTRI11
□ UPHTRI12
□ UPHTRI13
■ Standard Equipment
Seat upholstery with black embossed textile insert, black vinyl
bolster and blue vinyl side insert & textile interior trim in
matching grey/blue nuances
Seat upholstery with light grey embossed textile insert, raven
metallic vinyl bolster and red vinyl side insert & vinyl/textile
interior trim in matching skylark/grey/black nuances
Seat upholstery with blue soft textile insert, black vinyl bolster
& textile interior trim in matching grey/black/blue colours
Seat upholstery with dark grey leather insert and black leather
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
4 (6)
Ref: FM 66 T1CBX01 8EE 2016-09-08 ENGVT
FMX D11 66 Tractor all wheel drive B-ride FM 66 T1CBX
□ UPHTRI14
■
□
□
□
DST-CF1
DST-CF2
DST-CF4
DST-CF5
bolster & vinyl/textile interior trim in matching grey/black
nuances
Seat with dark grey leather insert and black leather bolster &
textile interior trim in matching grey and black colours
□ TABLE
Foldable and height adjustable table to be mounted to the
lower bunk
□ REF-ICPK
Refrigerator preparation kit, engine tunnel mounted
■ BOTH-D
One bottle holder under dashboard centre section
□ COFMA-PK
Preparation kit for coffee maker
■ INLI-BAS
Interior white light with smooth light transition at on/off, no
dimming
Interior white and red (night) light with smooth light transition at
on/off
Interior white and red (night) light with smooth light transition at
on/off and dimmer
□ DST-STD2
Driver seat, comfort, suspended
Driver seat, comfort, suspended, electrically heated
Driver seat, comfort, suspended, belt in seat
Driver seat, comfort, suspended, belt in seat, electrically
heated
Driver seat, comfort, suspended, belt in seat, electrically
heated, ventilated
Driver seat, reagular, suspended
□ SBD-RED
Red safety belts, passenge and driver seats
□ SBPRE-DS
Driver seat belt pretensioner
□ ARL-FLEX
Two flexible reading lamps (snake lamps)
Passenger seat, basic, non suspended
Bench passenger seat
Passenger seat, comfort, suspended, electrically heated
Passenger seat, comfort, suspended, belt in seat
Passenger seat, comfort, suspended, belt in seat, electrically
heated
□ RH-ECS
□ RH-MSR
■ URH
Roof hatch - Electrically operated / Clear glass / Sliding
Roof hatch - Manually operated / Steel / Rear opening
Without roof hatch
□ SWIND-PS
Rear side window on passenger side
□ SBPRE-PS
Passenger seat belt pretensioner
■ PAICS-B
□ ARM-DBPS
Two armrests on driver seat and one (outer) on passenger
seat
Two armrests on both driver and passenger seats
Two armrests on driver seat
Two armrests on passenger seat
Single armrest (next to driver) on passenger seat
Basic painting in a lightning grey colour of cab surrounding
parts (mirror housings, insteps, bumper and if fitted bumper
spoiler and sun visor).
If fitted roof air deflector, side air deflector and chassis fairings
are always painted in cab colour.
■ GLAS-TIN
□ GLAS-UNT
Tinted windows
Untinted windows
□ AWIND-RF
Rear fixed window (without curtains)
■ LOCK-MAN
□ LOCK-MRP
□ LOCK-REM
Manual door locking
Manual door locking with internal remote control (from driver
side) of passenger door
Central door locking with remote control
■ BUMP-HD
Heavy duty front bumper
□ AUXFS
Extra cab side foot-step
□ GUARD-EH
Guard plate for cooling pipes and oil sump
□ SIDEH-B
□ SIDSTP-R
Guide rail on day cab driver side
Side ladder and guide rail on on day cab driver side
■ BUGNET
Radioator screen.
Mosquito net in front of radiator
□ CTILTP-E
■ CTILTP-M
Electrical cab tilt pump
Manual cab tilt pump
□ FCABS-A
■ FCABS-M
Air front cab suspension
Mechanical front cab suspension
□ RCABS-A
■ RCABS-M
Air rear cab suspension
Mechanical rear cab suspension
□ MIRCOMFX
El heated & operared robust main rear view mirrors, electrically
heated wide angle mirrors (both sides).
Close view mirror on passenger side.
Electrically heated robust main rear view mirrors and wide
angle mirrors (both sides). Close view mirror on passenger
side.
□ DST-CF6
■
□
□
□
□
□
□
□
□
PST-BAS1
PST-BENC
PST-CF2
PST-CF4
PST-CF5
ARMRE-BB
ARMRE-DB
ARMRE-PB
ARMRE-PS
□ ARU-BAS
□ ARU-LEA
Vinyl armrest upholstery
Leather armrest upholstery
■ FMAT-RU2
Two black rubber floor mats with raised edges and an
extended side (FMX)
Two dark grey textile floor mats and two black rubber floor
mats with an extended side (FMX)
□ FMAT-T2E
□ LBK-RES
■ LBK70
□ ULBK
Lower fixed rest kit, foldable to rear wall
Lower fixed bunk, not foldable - 2000x700 mm. Safety net
included.
Without lower bunk
□ MATL-FI
■ MATL-SF
□ MATL-SO
Mattress lower bunk - firm, pocket springs
Mattress lower bunk - semi-firm, pocket springs
Mattress lower bunk - soft, pocket springs
□ OLMAT-BA
□ OLMAT-PR
Overlay mattress protector, 20 mm thick black textile
Overlay mattress protector, 30 mm thick black textile
□ TBK60F
□ TBK70F
Fixed top bunk 600x1900 mm, foldable up to 52 degrees to
rear wall (depending on cab version and upper storage). Safety
net included.
Fixed top bunk 700x1900 mm, foldable up to 52 degrees to
rear wall (depending on cab version and upper storage). Safety
net included.
□ PH-CAB2
□ PH-ENGCA
□ PH-SS
Cab parking heater, 2 kW
Engine and cab parking heater
Short stop heater
□ SLCP-BAS
Basic sleeper control panel (controlling interior light, parking
heater, roof hatch and door lock)
□ SAFE
Lockable safety box at bed end
□ ETSB-F
□ ETSB-FR
□ ETSB-FRS
Storage on engine tunnel - on front top
Storage on engine tunnel - on front top and at rear cab wall
Storage on engine tunnel - on front top & at rear cab wall &
storage immersed into tunnel on RH side
Storage on engine tunnel - on front top and storage immersed
into tunnel on right hand side
Fixed engine tunnel storage box at rear cab wall
Storage on engine tunnel - at rear cab wall and storage
immersed into tunnel on right hand side
Storage on engine tunnel - immersed into tunnel on right hand
side
□ ETSB-FS
□ ETSB-R
□ ETSB-RS
□ ETSB-S
□ RUS-BAS
Rear cab upper storage 154 litres (300 mm high)
■ Standard Equipment
□ INLI-NL
□ INLI-NLD
Cab Exterior
■ MIRSTDX
■ AMIR-F20
Front close view mirror above windscreen on passenger side
(radius 200 mm)
□ SUNV-H
Exterior smoke coloured front sun visor
□ AD-ROOF
□ AD-ROOFB
Roof air deflector. Design (length, height etc.) automatically
calculated and varies depending on vehicle total height
(chassis height, cab type, tyres etc).
Roof air deflector with light box
□ AD-SIDEL
□ AD-SIDES
Long cab side air deflector
Short cab side air deflectors
■ HL-BAS2
Halogen H1 head lamps (heavy duty)
□ HL-CLEAN
High pressure headlamp cleaner
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
5 (6)
Ref: FM 66 T1CBX01 8EE 2016-09-08 ENGVT
FMX D11 66 Tractor all wheel drive B-ride FM 66 T1CBX
□ HLP-ST
□ HLP-ST2
Steel headlamp protection
Steel wire mesh headlamp protection
□ RDECK-M
■ HL-ADJ
Adjustable headlights
□ SRWL-2RA
■ DRL-LED
V-shaped ("V-light") day running light (LED).
Turned on low beam gives a dimmed "V-light".
Without day running light (dimmed V-light)
□ SRWL-2RW
□ UDRL
□ ASL-RF2
□ ASL-RFPK
Two Hella H11 70W spot lamps in sign box (one on each side
of the Globetrotter sign)
Preparation kit for two spot lamps in sign box
□ SRWL-PK
□ IDLAMP-A
Three middle front roof mounted amber identification lamps
□ SWL-2RA
□ IDLMPSW
Switch in cab for identification lamps
□ BEACOA2F
Two front roof mounted amber rotating beacon warning lamps.
Mounted on accessory bracket if ordered, otherwise on cab
roof on both sides of the hatch.
Two rear roof mounted (on accessory bracket) amber warning
lamps.
Rotating beacon lamps mounted on sleeper cab.
Flashing LED lamps mounted on high/extra high sleeper cabs.
Prepared wiring (switch and connected relay included) for
warning lamps on cab roof.
Max load 300 W.
□ BEACOA2R
□ BEACON-P
□ SWL-2RW
□ SWL-PK
□ WL-TA1A
□ WL-TA1W
□ WLC-H2A
□ WLC-H2W
□ CABPT-R1
■ CABPT-R2
One front cab roof pass through on passenger side
Two front cab roof pass throughs, one on each side
□ WLC-PKH
□ SPOTP-F
□ SPOTP-R
□ SPOTP-RF
Spotlamp preparation in cab front, max 280W
Spotlamp preparation on cab roof, max 280W
Spotlamp preparation on cab roof and in cab front, max
2x280W
□ WLC-PKL
□ ROS-IL
□ ROS-ILP
Illuminated roof sign with switch in radio shelf
Wiring preparation kit for roof sign illumination
□ CSGN-FMX
FMX decal in the cab roof sign area
■ HORN-F1S
□ HORN-R2S
One front mounted (behind grille) single tone air horn, Jericho
Two roof mounted single tone chromed air horns
□ ANT-CBR
Roof mounted antenna for CB radio, single aerial
□ ACCBR-F
□ ACCBR-R
□ WLC-PKLH
left fuel tank or left battery box)
Medium rear deck (two plates between frame rails and one
over left fuel tank or left battery box)
Two H3 35W amber rear chassis mounted (LH/RH side)
working lamps and a 3-position switch (On/Off/Reverse auto
on)
Two H3 70W white rear chassis mounted (LH/RH side)
working lamps and a 3-position switch (On/Off/Reverse auto
on)
Wiring preparation for chassis mounted working lamps and a
3-position switch (On/Off/Reverse auto on).
Max load 280W.
Two H3 35W amber rear chassis mounted (LH/RH side)
working lamps and a 2-position switch (On/Off)
Two H3 70W white rear chassis mounted (LH/RH side)
working lamps and a 2-position switch (On/Off)
Wiring preparation for chassis mounted working lamps and a
2-position switch (On/Off). Max load 280W.
Trailer arch working lamp with amber coloured lens and
H3/35W bulb
Trailer arch working lamp with white lens and LED/70W bulb
Two H3/70W working lamps with amber coloured lens high
mounted back of cab (switch incl).
Two H3/70W working lamps, white lens high mounted back of
cab (switch incl).
Preparation kit (cables and switch) for high mounted working
lamps back of cab (pass through in cab rear roof included).
Max load 280W.
Preparation kit (cables and switch) for low mounted working
lamps back of cab (pass through in cab rear wall included).
Max load 280W.
Preparation kit (cables and switch) for low and high mounted
working lamps back of cab (pass throughs in rear wall and rear
roof included). Max load 280W.
■ ECBB-BAS
□ ECBB-HIG
Body builder electrical centre without body builder module
Body builder electrical centre with cab body builder module
□ BBCHAS1
□ BBCHAS3
One 7-pole connector for Body builder interface
Three 7-pole connectors for Body builder interface
Front roof mounted accessory bracket
Rear roof mounted accessory bracket
□ BEPR-T2
Body builder electrical software preparation for tipper with
remote control
□ LADDER
Ladder back of cab
□ REFS-TW
□ REFS-TY
Reflecting white cab side stripes by-packed in cab
Reflecting yellow cab side stripes by-packed in cab
□ TD-BAS
■ TD-LED
Trailer detection without LED sensor
Trailer detection with LED sensor
□ AUXL-SPK
Electrical preparation kit (wiring and switch) for snow plough
lights.
Preparation for installation of additional headlights and
additional turning indicators.
□ TAILPRE2
□ TAILPREP
Tail lift preparation kit, wireless remote operation
Tail lift preparation kit, wire remote operation
□ AESW2
Two Body builder bistable electrical switches (marked AUX1 /
AUX2)
Two Body builder bistable electrical switches (marked
AUX1/AUX2) and in an empty 4-group preparation for another
four bistable switches with dummy switch caps
Superstructure preparations
□ 5WM-ISOH
■ 5WM-ISOM
Fifth wheel ISO mounting on high Z-profiles (t=8 mm) with 10
mm ISO saddle.
Z-profile height above frame = 80 mm.
Total height above frame 90 mm.
Fifth wheel ISO mounting on medium L-profiles (t=8 mm) with
10 mm ISO tie plate.
L-profile height above frame = 50 mm.
Total height above frame 60 mm.
□
□
□
□
5WH150
5WH185
5WH190
5WH290
Fifth
Fifth
Fifth
Fifth
□
■
□
□
5WT-JO11
5WT-JO8
5WT-JOHD
5WT-SH
Jost JSK 38G cast iron heavy duty fixed fifth wheel
Jost JSK 37 cast iron fixed fifth wheel
Jost JSK 38C cast iron heavy duty fixed fifth wheel
SAF-Holland/+GF+ SK-S 36.20 V cast iron fixed fifth wheel
wheel leg-height 150 mm
wheel leg-height 185 mm
wheel leg-height 190 mm
wheel leg-height 290 mm
□ 5WL-S1
Fifth wheel lubrication - locking mechanism and top plate
□ TCIND
Trailer connection indication with sensors for height, kingpin
and coupling lock
□ RAMP-LOW
□ RAMP-MED
Low height sliding members/protection members
Medium height sliding members/protection members
■ RDECK
Basic rear deck (one plate between frame rails and one over
■ Standard Equipment
□ AESW2PK
□ AUXSW-4
Wiring for 4 extra hardwired switches (from Body builder
electrical centre to switch positions)
Services
□ TGW-3GWL
■ TGW-PK
Telematics gateway with 3G modem and WLAN
Telematics gateway preparation kit
□ FMS-PK
Fleet Management System gateway, preparation kit
□ DRUT
My truck app gives the driver instant status information and
control of the vehicle remotely from a smartphone or tablet.
The variant enables the My truck app to connect to the vehicle.
□ Optional Equipment
For more detailed information about cab and powertrain equipment, please refer to separate specification sheets.
For all possible options and combinations of options please consult your Volvo sales contact who can create a specification to match your requirements using the
Volvo Sales Support system (VSS).
The factory reserves the right to modify design and change equipment without previous notification.
The specification can vary from country to country.
6 (6)
Ref: FM 66 T1CBX01 8EE 2016-09-08 ENGVT
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement