advertisement
▼
Scroll to page 2
of 112
3-085-095-71(2) DVD Recorder RDR-GX7 Operating Instructions © 2003 Sony Corporation WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. The AC power cord must be changed only at a qualified service shop only. CAUTION The use of optical instruments with this product will increase eye hazard. As the laser beam used in this DVD recorder is harmful to eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. For customers in the U.S.A Owner’s Record The model and serial numbers are located at the rear of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. RDR-GX7 Serial No.______________ CAUTION You are cautioned that any change or modifications not expressly approved in this manual could void your authority to operate this equipment. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. VCR Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The VCR Plus+ system is manufactured under license from Gemstar Development Corporation. Precautions This equipment has been tested and found to comply with the limits set out in the EMC Directive using a connection cable shorter than 3 meters. On safety Should any solid object or liquid fall into the cabinet, unplug the recorder and have it checked by qualified personnel before operating it any further. On power sources • The recorder is not disconnected from the AC power source as long as it is connected to the wall outlet, even if the recorder itself has been turned off. • If you are not going to use the recorder for a long time, be sure to disconnect the recorder from the wall outlet. To disconnect the AC power cord, grasp the plug itself; never pull the cord. On placement • Place the recorder in a location with adequate ventilation to prevent heat build-up in the recorder. • Do not place the recorder on a soft surface such as a rug that might block the ventilation holes. • Do not place the recorder in a confined space such as a bookshelf or similar unit. • Do not place the recorder in a location near heat sources, or in a place subject to direct sunlight, excessive dust, or mechanical shock. • Do not place the recorder in an inclined position. It is designed to be operated in a horizontal position only. • Keep the recorder and discs away from equipment with strong magnets, such as microwave ovens, or large loudspeakers. • Do not place heavy objects on the recorder. • To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus. On operation • If the recorder is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the recorder. Should this occur, the recorder may not operate properly. In this case, remove the disc and leave the recorder turned on for about half an hour until the moisture evaporates. • When you move the recorder, take out any discs. If you don’t, the disc may be damaged. 2 WARNING On recording • Contents of the recording cannot be compensated if the recording or playback is not made due to a malfunction of the recorder, disc, etc. • Make trial recordings before taking the actual recording. On adjusting volume Do not turn up the volume while listening to a section with very low level inputs or no audio signals. If you do, the speakers may be damaged when a peak level section is played. On cleaning Clean the cabinet, panel, and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzine. On cleaning discs Do not use a commercially available cleaning disc. It may cause a malfunction. Copyrights • Television programs, films, video tapes, discs, and other materials may be copyrighted. Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or program owner. • This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. Copy guard function Since the recorder has a copy guard function, programs received through an external tuner (not supplied) may contain copy protection signals (copy guard function) and as such may not be recordable, depending on the type of signal. Music discs encoded with copyright protection technologies This product is designed to playback discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product. IMPORTANT NOTICE Caution: This recorder is capable of holding a still video image or on-screen display image on your television screen indefinitely. If you leave the still video image or on-screen display image displayed on your TV for an extended period of time you risk permanent damage to your television screen. Plasma display panels and projection televisions are especially susceptible to this. 12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. 13 Unplug this apparatus during lightning storms or when unused for long periods of time. 14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Notes about the discs • To keep the disc clean, handle the disc by its edge. Do not touch the surface. Dust, fingerprints, or scratches on the disc may cause it to malfunction. If you have any questions or problems concerning your recorder, please consult your nearest Sony dealer. IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11 Only use attachments/accessories specified by the manufacturer. • Do not expose the disc to direct sunlight or heat sources such as hot air ducts, or leave it in a car parked in direct sunlight as the temperature may rise considerably inside the car. • After playing, store the disc in its case. • Clean the disc with a cleaning cloth. Wipe the disc from the center out. • Do not use solvents such as benzine, thinner, commercially available cleaners, or anti-static spray intended for vinyl LPs. • Do not use the following discs. – A disc that has a non-standard shape (e.g., card, heart). – A disc with a label or sticker on it. – A disc that has cellophane tape or sticker adhesive on it. Precautions 3 Using the Quick Timer function .................... Recording a stereo program and SAP ......... Checking the disc status while recording ..... Creating chapters in a title ........................... Table of Contents 39 39 40 40 Timer Recording ..................................... 40 WARNING ...................................................2 Precautions ................................................2 Notes about the discs..................................... 3 Features ......................................................6 Recording....................................................... Playback......................................................... Editing a disc.................................................. DV Edit ........................................................... 6 6 6 7 About This Manual .....................................7 DVD Recorder Basics ................................8 Guide to Parts and Controls ...................11 Front panel ...................................................11 Remote .........................................................12 Front panel display....................................... 14 Rear panel ....................................................14 Basic Hookups and Settings Quick Overview ........................................15 Step 1: Unpacking ...................................16 Step 2: Connecting the Antenna Cable ....................................................16 Step 3: Connecting the Video Cords .....18 Step 4: Connecting the Audio Cords .....19 Step 5: Connecting the Power Cord ......22 Step 6: Preparing the Remote ................22 Step 7: Easy Setup ..................................22 Setting Up the VCR Plus® System .........25 Setting Up the Remote ............................26 Controlling TVs with the remote ................... 26 Controlling the volume of your AV amplifier (receiver) with the remote....................... 27 If you have a Sony DVD player or more than one Sony DVD recorder ......................... 28 Connecting a VCR or Similar Recording Device to the LINE Jacks ...................29 Connecting to a Satellite Receiver or a Cable Box ............................................30 Operating the Recorder Guide to Displays ....................................31 System Menu ............................................... Title List........................................................ TOOLS ......................................................... Sub-menu..................................................... 31 32 32 33 How to Use the Displays .........................33 How to Enter Characters .........................34 Before Recording .....................................35 35 36 36 36 37 Recording TV programs ..........................38 4 Table of Contents Adjusting the Recording Picture Quality and Size .............................................. 46 Recording from External Equipment with a Timer (Synchro Rec) .......................... 47 Playback Before Playing ......................................... 49 Playable discs .............................................. 49 Playing Discs ........................................... 50 Using the DVD’s Menu................................. 51 Using the PROGRESSIVE button................ 51 Basic operations/Changing the playback speed...................................................... 52 Selecting a Recorded Title on a Disc .... 53 Searching for a Title/Chapter/Track ...... 55 Checking the Play Information and Playing Time .................................................... 56 Checking the playing time on the front panel display .................................................... 57 Selecting the Sound ............................... 57 Checking the audio signal format................. 58 TV Virtual Surround Settings (TVS) ...... 58 Changing the Angles .............................. 59 Displaying the Subtitles ......................... 60 Adjusting the Playback Picture and Sound .................................................. 60 Adjusting the picture quality ......................... 60 Adjusting the sound quality .......................... 61 Editing a DVD Before Editing ......................................... 62 Checking the disc type, recording format, and title type .................................................. 62 Edit options for DVD-RWs (Video mode)/ DVD+RWs/DVD-Rs................................ 62 Edit options for DVD-RWs (VR mode) ......... 63 Basic Editing ........................................... 64 Labeling a title (Title Name) ......................... Protecting a title (Protect Title)..................... Erasing a title (Erase)................................... Erasing multiple titles (Erase Titles)............. Erasing a section of a title (A-B Erase) ........ Creating chapters manually ......................... 64 64 65 65 66 67 Advanced Editing (Playlist Edit) ............ 67 Recording/Timer Recording Recordable discs.......................................... About recording formats............................... Recording mode........................................... Unrecordable pictures .................................. Checking the available disc space (Disc Info.) .............................................. Setting the timer manually (Standard).......... 40 Checking/changing/canceling timer settings (Timer List) ............................................. 42 Changing the priority of overlapped settings ................................................... 43 Recording TV programs using the VCR Plus+ system .................................................... 44 Creating a Playlist title from other titles........ Moving a Playlist title (Move Title)................ Dividing a Playlist title (Divide Title) ............. Combining multiple Playlist titles (Combine Titles)...................................................... Additional Playlist edit functions................... 67 70 70 71 71 Labeling, Protecting, or Finalizing the Disc ..................................................... 72 Labeling a disc (Disc Name) ....................... Protecting a disc (Protect Disc) ................... Finalizing a disc (Finalize) ........................... Erasing all the titles on the disc (Erase All) .............................................. Reformatting a disc (Format)....................... 72 72 73 73 74 Connecting a Digital Video Camera or Other Equipment Before Recording/Editing ....................... 75 Preparing for recording using the DV IN jack ........................................................ 75 Available DV Dubbing Functions .......... 77 Recording an Entire DV/Digital8 Format Tape (ONE TOUCH DUB) ................... 78 Program Edit ........................................... 79 Advanced Program Edit ......................... 81 Re-editing the “program” in the DV/D8 Edit List ...................................................... 84 Creating a Copy of the Edited Contents (Copy Dubbing) .................................. 86 Recording From Equipment Connected to the LINE IN Jacks ............................... 88 Connecting other equipment to the LINE 2 IN jacks....................................................... 88 Recording from connected equipment ........ 88 Settings and Adjustments About the Setup Display Structure ....... 90 Using the Setup Displays ....................... 91 Settings (Basic Settings) ........................ 92 Video Settings ......................................... 94 Audio Settings ......................................... 95 Features Settings .................................... 97 Options Settings ..................................... 99 Easy Setup (Resetting the Recorder) ................. 100 Additional Information Troubleshooting .................................... 101 Self-diagnosis Function (When letters/numbers appear in the display) ............................................. 104 Specifications ........................................ 105 About i.LINK .......................................... 106 About the Name “i.LINK” ........................... i.LINK Baud rate ........................................ i.LINK functions on this recorder ............... Required i.LINK Cable............................... 106 106 106 106 Glossary ................................................. 107 Language Code List .............................. 108 Index ....................................................... 109 Quick Guide to DVD Disc Types ................................................back cover Table of Contents 5 Features Playback Easy playback with the Title List menu (page 53) This recorder can play DVDs or CDs, record on DVD-Rs, DVDRWs or DVD+RWs, and by using a variety of editing functions, you can enjoy editing recorded programs and other images. Recording The recorder will display all of the titles you recorded on a disc in a list display, called the “Title List.” By selecting a title from the Title List menu, you can easily start playing or editing the disc. Moreover, you can have the recorder show the title’s contents using thumbnail images. The recorder also automatically takes program label information from the XDS (Extended Data Service)* and displays it as the title name. * not available in some areas Dual RW compatible (page 35) Title List The recorder is compatible with rewritable disc types, DVD-RW and DVD+RW, and the write-once type, DVD-R. These available disc types accommodate a wide range of uses, such as recording programs and creating personal video libraries. These discs can be played back on a wide variety of other DVD equipment. -RW.VR Sort Date Number Title TITLE LIST ORIGINAL My Movies 1.5/4.7GB 1 2ch 1:00PM - 2:00PM 2ch Mon 9/15 1:00PM( 1H00M) SP 2 5ch 8:00PM - 9:00PM 5ch Wed 9/17 8:00PM( 1H00M) SLP 3 12ch 9:00AM - 9:30AM 12ch EP Thu 9/25 9:00AM( 0H30M) 4 3ch 8:00PM - 8:30PM 3ch Thu 9/25 8:00PM( 0H30M) SLP TV Virtual Surround Settings, “TVS” (page 58) DVD-RW DVD+RW DVD-R Various recording/timer recording functions (page 35) Using only your TV’s stereo speakers, the recorder is capable of reproducing dynamic surround sound from DVD-Video software’s multi-channel audio signals. There are four surround modes to choose from. Editing a disc In addition to the usual recording functions, such as Timer Recording and VCR Plus+, Synchro Rec allows synchronized recording with a set top box or similar device. Playlist edit (DVD-RW in VR mode only) (page 67) Automatic searching for recording space (page 37) You can edit not only the recorded original title, but also perform advanced edit functions by creating a Playlist on the same disc. Since a Playlist does not require much disc space, you can create numerous Playlist titles. A Playlist edit can be redone as many times as you like, as the original title remains unchanged. The recorder automatically searches for available blank space on the disc after you press the Rec button. No searching is required on your part – a feature possible only with a DVD recorder. Adjustments for both recording and playback picture (page 46, 60) The recorder allows you to adjust the picture quality of input sources, such as a VCR, which can then be recorded on a DVD. For instance, if you want to create an archive of your VHS tapes, you can adjust the recording picture quality to compensate for the quality of the tapes. Various picture quality adjustments are also available for DVD-Video software playback. Chapter Marking function (page 67) On DVD-RWs in VR mode, you can manually insert chapter marks to divide a title into chapters which will enable you to quickly find specific scenes for playback or editing. For other disc types and recording formats, the recorder automatically creates chapter marks at specified intervals while recording. Quick Search function (page 52) The remote has a Jog Stick for the recorder’s main operations. You can search forward or backwards, or play at various speeds by using just your thumb. The feature helps you find scenes easily, which is especially useful for both playback and editing. Search Jog Stick Slow motion 6 Features About This Manual DV Edit Only one i.LINK cable is required to transfer contents from a digital video camera to the DVD recorder. Since the recorder controls the digital video camera, dubbing and editing are easy to perform. Control Dubbing Instructions in this manual describe the controls on the remote. You can also use the controls on the recorder if they have the same or similar names as those on the remote. The meanings of the icons used in this manual are described below: Icon Meaning Functions available for DVD VIDEOs or DVD+Rs Functions available for DVD-RWs formatted in VR mode on this recorder Functions available for DVD-RWs formatted in Video mode on this recorder One Touch Dubbing function (page 78) One press on the ONE TOUCH DUB button is enough to complete the procedure. The recorder controls the digital video camera from start to finish — from playing the DV/Digital8 format tape to stop and rewind. The entire tape contents are dubbed to a DVD in the process. Program Edit (page 79) This function allows you to select scenes on a DV/Digital8 format tape and save them on recordable DVDs, including nonrewritable DVD-Rs. The recorder controls the digital video camera to record the contents of a DV/Digital8 format tape to the disc as programmed. The recorder will remember which scenes you selected and saves this information as a program. You can call up a program at any time and make additional copies of the program to DVDs. Functions available for DVD+RWs Functions available for DVD-Rs Functions available for music CDs or CDRs/CD-RWs in music CD format Notes • The on-screen display illustrations used in this manual may not match the graphics displayed on your TV screen. • The explanations regarding discs in this manual refer to discs created on this recorder. The explanations do not apply to discs that are created on other recorders and played back on this recorder. Advanced Program Edit (page 81) This function takes advantage of a DVD’s random access capabilities to enable fast and flexible editing. The recorder copies the entire contents of a DV/Digital8 format tape to a DVD-RW in VR mode, whereupon the contents are automatically divided into chapters. The chapters are displayed as scenes in a scene list where you can instantly delete or rearrange the scenes at will. The recorder remembers which scenes you selected, and saves this information as a program. You can call up a program at any time and make additional copies of the program to a DVD. Auto Scene Chaptering (DVD-RW in VR mode only) (page 78, 79, 81) While copying a DV/Digital8 format tape to a DVD-RW, the recorder automatically inserts chapter marks at each point where you started recording on your digital video camera. This enables you to quickly find the scenes you want during playback and editing. About This Manual 7 DVD Recorder Basics “What can I expect from DVD recording?” is a natural question for anyone new to the experience. This section explains the basic steps involved with DVD recording. Step 1: Select the disc type Unlike a video tape which is sold by length, such as 60 min. or 120 min., recordable DVDs are sold by type. Select the disc type by following the chart on the back cover, as each type has different features. This recorder can record on the following type of discs. When you want to record repeatedly on the same disc, or when you want to edit the disc after recording, select either the rewritable DVD-RW or DVD+RW type disc. When you want to save recordings without any alteration, a non-rewritable DVD-R can be your choice. Note There are other differences besides just being rewritable/non-rewritable. See “Quick Guide to DVD Disc Types” on the back cover to select a disc most suitable for your needs. Step 2: Format the disc to start recording Insert the disc in the recorder. Unlike a VCR, the recorder automatically starts formatting when an unused disc is inserted. This is necessary to prepare the disc for recording. When using a DVD-R When using a DVD-RW Notes • You cannot mix two formats in one DVD-RW. • You can change a DVD-RW’s format to the other format. However, the disc’s contents will be lost when reformatting. • Not all discs can be played on other DVD equipment. This type of disc can be formatted in either DVD Video format (Video mode) or DVD Video Recording format (VR mode). Video mode discs can be played back on a variety of other DVD equipment.VR mode discs allow for more varied editing. When using a DVD+RW These discs will be formatted in DVD+RW Video format. This type of disc can be played back on a variety of other DVD equipment. 8 DVD Recorder Basics These discs will be formatted in DVD-Video format. This type of disc can be played back on a variety of other DVD equipment. When formatting is complete, you are ready to record on the disc. Step 3: Digital Recording Record a program. When using the timer, you’ll find familiar, convenient features as found on conventional VCRs, such as VCR Plus+. You can also dub and edit the contents of connected video equipment such as a digital video camera. Step 4: Playing the recorded contents You can select the title you want to play from a displayed menu, and immediately start playback. Recorded contents are more accessible on a disc than on a tape, the procedure is simple, and unlike conventional VCRs, no rewinding is necessary! A recorded disc contains title(s), and each title contains chapter(s) Start Rec. Stop/Start Stop Rec. Title 1 Title 2 Chapters Chapters What are titles and chapters? DVD contents consist of sections, called titles, and smaller sub-sections called chapters. On this recorder, a title is created between the points where you start and stop a recording. Chapters are created automatically at specified intervals, or can be created manually (DVD-RWs in VR mode only). Chapter marks Chapter marks Go to the next page. ,continued DVD Recorder Basics 9 Step 5: Editing the recorded disc You will find editing discs a lot easier than a conventional tape, and the recorder offers numerous edit functions, possible only with DVDs. Quick and easy edits on the displayed menu Editing is performed by simply selecting titles and scenes from the displayed menus. Protection of individual titles With conventional VCRs, you had to protect an entire tape to save the recordings from erasure or alteration. This recorder allows you to individually protect recorded titles (except for Playlist titles). Edit and save on a single disc – Playlist edit (DVD-RWs in VR mode only) To edit a conventional tape without affecting the original recording, you had to connect another VCR, copy the master tape using the two VCRs and one more tape, and start editing the copied tape. With this recorder, you can create a Playlist (playback information) on the same disc, and edit the Playlist without changing the original recording(s). A Playlist does not take up much disc space, and all you need is one recorder and one disc. Example: You have recorded a few football games on a DVD-RW in VR mode. You want to save the original recording, but you also want to create a digest by putting the goal scenes together. In this case, you can create a Playlist by selecting just the goal scenes, leaving the original recording as it is. Original Playlist You’ve got your own DVD! Playing on other DVD equipment For your DVD to play on other equipment, finalizing may be necessary in some cases. If so, finish up all your editing and recording first, and then finalize the disc. When using a DVD-RW in VR mode Although finalizing is generally unnecessary when playing the disc on VR mode compatible equipment, playback on some equipment requires a finalized disc. You can still edit and record on the disc even after finalizing. When using a DVD+RW The recorder automatically finalizes a disc before ejecting it. Finalizing in this case still allows you to further edit or record on the disc. 10 DVD Recorder Basics When using a DVD-RW in Video mode The disc needs to be finalized first to enable playback on anything other than this recorder. No more editing or recording can be made on the disc once it has been finalized. To enable recording on the disc again, you will need to format it again. (Reformatting will erase all previous contents.) When using a DVD-R You will need to finalize the disc to play it on equipment other than this recorder. You cannot edit or record on the disc once it has been finalized. Guide to Parts and Controls For more information, see the pages in parentheses. Front panel Buttons on the recorder have the same function as the buttons on the remote if they have the same or similar names. Open the panel. A @/1 (on/standby) button/ indicator (22, 38) Turns the recorder on and off. Lights up in green when the power is on. B Front panel display (14, 57) Displays the playing status, title/chapter/time, etc. C Disc tray (38) Opens to accept a disc. D (remote sensor) (22) Accepts the remote control signal. E Disc type indicators Lights up to indicate the disc/ format type of the current disc. F A (open/close) button (38) Opens or closes the disc tray. G H (play) button/indicator (50) Plays a disc. H X (pause) button/indicator (52) Pauses playing a disc. I x (stop) button (51) Stops playing a disc. J z REC button/indicator (38) Starts recording. K X REC PAUSE button/indicator (39) Pauses recording. L x REC STOP button (39) Stops recording. M SYNCHRO REC indicator (47) Lights up when the Synchro Rec function is set to on. TIMER REC indicator (40) Lights up when a timer recording is set. FINALIZED indicator (73) Lights up if an inserted disc has been finalized. PROGRESSIVE indicator (51) Lights up when outputting progressive signals. N ZOOM +/– buttons (32) Switches the information displayed in the Title List menu. O CURSOR MODE button (32) Switches the cursor/page mode in the Title List, etc. P TOOLS button (32) Displays the TOOLS menu. Q </M/m/,/ENTER button (33) Selects items or settings. R RETURN button (33) Returns to the previously selected display, etc. S SYSTEM MENU button (31) Displays the System Menu on the TV screen. T ONE TOUCH DUB button (78) Records the contents of a DV/ Digital8 format tape with a single touch of the button. U REC MODE button (38) Selects the recording mode. V ./> (previous/next) buttons (52) Goes to the next title/chapter/ track, or goes back to the previous title/chapter/track. W CHANNEL +/– buttons (38) Selects the channel or input line. X PROGRESSIVE button (51) Switches the output signal, progressive or interlace. Y INPUT SELECT button (38, 75, 88) Selects equipment connected to the line inputs. Z LINE 2 IN (S VIDEO/VIDEO/ AUDIO L/R) jacks (88) Connects external equipment. wj DV IN jack (76) Connects digital equipment with a DV jack. ,continued Guide to Parts and Controls 11 Remote Buttons on the remote have the same function as the buttons on the recorder if they have the same or similar names. Buttons with an orange dot next to them can be used with your TV when the TV/DVD switch is set to TV. A TV/DVD switch (26) Switches the remote control to TV or DVD. B Z OPEN/CLOSE button (38) Opens or closes the disc tray. Note that it may take a few seconds for the disc tray to open after you have recorded or edited a disc. C Number buttons (38, 44) Select a number such as a channel or a title number. The number 5 button has a tactile dot.* D CLEAR button (44) Cancels an entered number when used with this recorder. E SUBTITLE button (60) Changes the subtitles while playing a disc. F AUDIO button (57) Changes the sound while playing a disc. The button has a tactile dot.* G [TIMER] button (40, 44) Displays the Timer programming menu on the TV screen. H TOP MENU button (51) Displays the disc’s menu on the TV screen. I DISPLAY button (40, 56) Displays disc information or playing/recording status on the TV screen. J TIME/TEXT button (56) Displays the time information of the disc. K SYSTEM MENU button (31) Displays the System Menu on the TV screen. L TITLE LIST button (32, 53, 64) Displays the Title List menu on the TV screen. M CURSOR MODE button (32) Switches the cursor/page mode in the Title List, etc. N RETURN button (33) Returns to the previously selected display, etc. Slide the cover. O . PREV (previous) button (52) Goes back to the previous title/chapter/track. P m / M (search) Jog Stick (52) Searches fast-forward or reverses a scene (while playing a disc), or plays a disc in slow motion or frame by frame (in the pause mode). Q H PLAY button (50) Plays a disc. The button has a tactile dot.* R X PAUSE button (52) Pauses playing a disc. 12 Guide to Parts and Controls S z REC button (38) Starts recording. r; CHAPTER MARK/ERASE buttons (67) Inserts/erases a chapter mark in the recorded title. T REC MODE button (38) Selects the recording mode. ra SUR (surround) button (58) Selects the surround mode. U INPUT SELECT button (38, 75, 88) Selects equipment connected to the line inputs. rs COMMAND MODE switch (DVD 1,2,3) (28) Switches the command mode for this recorder. Match the switch to the same command mode set in the Options Setup (page 99). V SYNCHRO REC button (47) Synchronizes the recorder and the timer recording set on the connected external equipment. * Use the tactile dot as a reference when operating the recorder. W [/1 (on/standby) button (38) Turns the recorder on and off. X CH (channel) +/– buttons (38) Selects the channel or input line. Y VOL (volume) +/– buttons (26) Adjusts the volume of your TV or AV amplifier (receiver). Z SET button (34) Use to enter the number selected with the number buttons 3. wj TV/VIDEO button (26) Switches your TV’s input source. wk ANGLE button (59) Changes the angles when playing a DVD VIDEO. wl WIDE MODE button (26) Changes the wide mode settings of your TV. e; MENU button (51) Displays the disc’s menu on the TV screen. ea INSTANT SEARCH button (52) Briefly fast forwards the current scene. es INSTANT REPLAY button (52) Replays the current scene. ed TOOLS button (32) Displays the TOOLS menu. ef ZOOM +/– buttons (32) Switches the information displayed in the Title List menu. eg </M/m/,/(ENTER) button (33) Selects items or settings. eh > NEXT button (52) Goes to the next title/chapter/track. ej x STOP button (51) Stops playing a disc. ek x REC STOP button (39) Stops recording. el X REC PAUSE button (39) Pauses recording. ,continued Guide to Parts and Controls 13 Front panel display A Command mode indicator (28, 99) Indicates the selected remote command mode. E SAP (Second Audio Program) indicator (39) Lights up when receiving a SAP signal. B ANGLE indicator (59) Lights up when you can change the angle. F CATV indicator Lights up when receiving a Cable TV programs. C PLAYLIST indicator (32) Lights up when the Playlist is selected. G Displays the following (57): • Playing time/remaining time • Current title/chapter/track/ index number • Recording time • Clock • Channel H Audio signal indicators (58) Lights up when playing Dolby Digital or DTS sound tracks. D STEREO indicators (39) Lights up when receiving a stereo program. z Hint You can turn off the front panel display by setting “Dimmer” to “Display Off” in Options Setup (page 99). Rear panel VHF/UHF IN DIGITAL OUT LINE IN PCM/DTS/DOLBY DIGITAL R-AUDIO-L COAXIAL OUT CONTROL S IN OPTICAL LINE OUT S VIDEO R-AUDIO-L VIDEO S VIDEO Y VIDEO 1 1 PB 3 2 PR COMPONENT VIDEO OUT A VHF/UHF IN/OUT jacks (16) Connects antenna cables. B COMPONENT VIDEO OUT (Y, PB, PR) jacks (18) Connects equipment having component video input jacks. C AC IN terminal (22) Connects the power cord. D LINE OUT (S VIDEO/VIDEO/ AUDIO L/R) 1/2 jacks (18, 20) Connects the input of external equipment using an audio/ video or S VIDEO cord. 14 Guide to Parts and Controls E LINE IN (S VIDEO/VIDEO/AUDIO L/R) 1/3 jacks (29) Connects the output of external equipment using an audio/ video or S VIDEO cord. F DIGITAL OUT (COAXIAL/ OPTICAL) jacks (20) Connects an amplifier (receiver) having a digital input jack. G CONTROL S IN jack (18) Connects equipment having a CONTROL S jack. ~ AC IN Quick Overview A quick overview presented in this guide will give you enough information to start using the recorder. Step 1: Unpacking m Step 2: Connecting the Antenna Cable m Step 3: Connecting the Video Cords m Step 4: Connecting the Audio Cords Basic Hookups and Settings Basic Hookups and Settings m Step 5: Connecting the Power Cord m Step 6: Preparing the Remote m Step 7: Easy Setup Notes • You cannot connect this recorder to a TV that does not have a video input jack. • Be sure to disconnect the power cord of each component before connecting. • Quick Overview . . . . . . . . . . . . . . . . . .page 15 • Step 1: Unpacking . . . . . . . . . . . . . . . .page 16 • Step 2: Connecting the Antenna Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 16 • Step 3: Connecting the Video Cords. . .page 18 • Step 4: Connecting the Audio Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 19 • Step 5: Connecting the Power Cord . . .page 22 • Step 6: Preparing the Remote . . . . . . .page 22 • Step 7: Easy Setup . . . . . . . . . . . . . . . .page 22 • Setting up the VCR PlusR System. . . .page 25 • Setting Up the Remote . . . . . . . . . . . . .page 26 • Connecting a VCR or Similar Recording Device to the LINE Jacks. . . . . . . . . . . . . . . . .page 29 • Connecting to a Satellite Receiver or a Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 30 Quick Overview 15 Step 1: Unpacking Hookup 1: Antenna only (no cable TV), or cable without cable box Check that you have the following items: • Audio/video cord (pinplug × 3 y pinplug × 3) (1) • Power cord (1) • Antenna cable (1) • Remote commander (remote) (1) • Size AA (R6) batteries (2) Use this hookup if you are using a VHF/UHF antenna or separate VHF and UHF antennas. Also use this hookup if you watch cable channels without cable box. With this hookup, you can record any non-scrambled channel by selecting the channel on the recorder. to VHF/UHF IN Step 2: Connecting the Antenna Cable DVD recorder VHF/UHF IN DIGITAL OUT LINE IN PCM/DTS/DOLBY DIGITAL R-AUDIO-L COAXIAL OUT CONTROL S IN OPTICAL LINE OUT S VIDEO R-AUDIO-L VIDEO S VIDEO Y VIDEO 1 1 PB 3 2 PR COMPONENT VIDEO OUT VHF/UHF IN Select one of the following antenna hookups that best suits you below. Do not connect the power cord until you reach “Step 5: Connecting the Power Cord” (page 22). If you have Use Antenna only (no cable TV), or cable without cable box Hookup 1 (page 16) Cable box with many scrambled channels Hookup 2 (page 17) Cable box with a few scrambled channels Hookup 3 (page 17) Note to CATV system installer (in USA) This reminder is provided to call the CATV system installer’s attention to Article 820- 40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. Notes • If your antenna is a flat cable (300-ohm twin lead cable), use an external antenna connector (not supplied) to connect the antenna to the recorder. • If you have separate cables for VHF and UHF antennas, use a UHF/ VHF band mixer (not supplied) to connect the antenna to the recorder. 16 Step 1: Unpacking OUT TV to VHF/UHF OUT to antenna input Antenna cable (supplied) : Signal flow ~ AC IN Hookup 3: Connecting a cable box with only a few scrambled channels Use this hookup if your cable system scrambles all or most channels. With this hookup: – You can record any unscrambled channel by selecting the channel on the cable box. Be sure that the cable box is turned on. – You cannot record one channel while watching another channel. Use this hookup if your cable system scrambles only a few channels. With this hookup: – You can record any non-scrambled channel by selecting the channel on the recorder. – You cannot record scrambled channels that require a cable box. Wall Wall DVD recorder Cable box VHF/UHF IN IN DIGITAL OUT LINE IN PCM/DTS/DOLBY DIGITAL R-AUDIO-L COAXIAL OUT OUT CONTROL S IN OPTICAL LINE OUT S VIDEO R-AUDIO-L VIDEO S VIDEO Y ~ AC IN VIDEO 1 1 PB 3 2 PR COMPONENT VIDEO OUT Basic Hookups and Settings Hookup 2: Connecting a cable box with many scrambled channels VHF/UHF IN DVD recorder to VHF/UHF IN VHF/UHF IN DIGITAL OUT LINE IN PCM/DTS/DOLBY DIGITAL R-AUDIO-L COAXIAL OUT CONTROL S IN OPTICAL LINE OUT S VIDEO VIDEO R-AUDIO-L 1 1 3 2 Y S VIDEO ~ AC IN VIDEO PB OUT PR COMPONENT VIDEO OUT to VHF/UHF OUT VHF/UHF IN to VHF/UHF IN OUT to VHF/UHF OUT Cable box TV IN TV OUT to antenna input to antenna input Antenna cable (supplied) Antenna cable (supplied) : Signal flow : Signal flow z Hint If the cable box has the audio/video output jacks, connect them to the LINE IN 1 or 3 jacks of this recorder. You can record unscrambled channels by setting the recorder’s input to “L1” or “L3.” Note When connecting the cable box with the antenna hookup only, set the recorder to the channel where the signal from the cable box appears on the TV screen. Step 2: Connecting the Antenna Cable 17 Step 3: Connecting the Video Cords C Connecting to component video input jacks (Y, PB, PR) Connect this recorder to your TV monitor, projector, or AV amplifier (receiver) using a video cord. Select one of the following patterns A through C, according to the input jack on your TV monitor, projector, or AV amplifier (receiver). This will enable you to view pictures. Audio connections are explained in “Step 4: Connecting the Audio Cords” (page 19). Connect the component via the COMPONENT VIDEO OUT jacks using a component video cord (not supplied) or three video cords (not supplied) of the same kind and length. You will enjoy accurate color reproduction and high quality images. If your TV accepts progressive (480p) format signals, you must use this connection and then press PROGRESSIVE on the front panel to accept progressive video signals. See “Using the PROGRESSIVE button” (page 51) for more information. DVD recorder If you are connecting to a VCR VHF/UHF IN DIGITAL OUT Connect your VCR to the LINE IN (VIDEO) jack on the recorder (page 29). LINE IN PCM/DTS/DOLBY DIGITAL R-AUDIO-L COAXIAL OUT CONTROL S IN OPTICAL R-AUDIO-L ~ Y S VIDEO AC IN VIDEO 1 PB 3 2 PR COMPONENT VIDEO OUT to COMPONENT VIDEO OUT A Connecting to a video input jack Connect the yellow plug of the audio/video cord (supplied) to the yellow (video) jacks. You will enjoy standard quality images. Use the red and white plugs to connect to the audio input jacks (page 20). LINE OUT S VIDEO VIDEO 1 (green) (green) (blue) (blue) (red) (red) COMPONENT VIDEO IN Y Y PB PB PR COMPONENT VIDEO OUT PR TV, projector, or AV Component video amplifier (receiver) cord (not supplied) DVD recorder VHF/UHF IN DIGITAL OUT LINE IN PCM/DTS/DOLBY DIGITAL R-AUDIO-L COAXIAL OUT CONTROL S IN OPTICAL LINE OUT S VIDEO R-AUDIO-L VIDEO ~ Y S VIDEO AC IN VIDEO 1 1 PB 3 2 PR : Signal flow COMPONENT VIDEO OUT LINE OUT R-AUDIO-L S VIDEO When connecting to a standard 4:3 screen TV to LINE OUT (VIDEO) 1 or 2 VIDEO 1 Depending on the disc, the image may not fit your TV screen. To change the aspect ratio, see page 94. 2 (yellow) INPUT (yellow) VIDEO L AUDIO Audio/video cord (supplied) R TV, projector, or AV amplifier (receiver) : Signal flow If your TV has a CONTROL S jack You can control the recorder by operating the remote toward the TV. This feature is convenient when you placed the recorder and the TV away from each other. After connecting the recorder to other equipment in pattern A, B, or C above, connect the CONTROL S IN jack to your TV’s CONTROL S (OUT) jack using a control S cord (not supplied). Refer to the instructions supplied with the TV to be connected. DVD recorder VHF/UHF IN DIGITAL OUT LINE IN PCM/DTS/DOLBY DIGITAL B Connecting to an S VIDEO input jack R-AUDIO-L COAXIAL OUT CONTROL S IN OPTICAL LINE OUT S VIDEO R-AUDIO-L VIDEO S VIDEO ~ Y AC IN VIDEO 1 1 PB 3 2 PR COMPONENT VIDEO OUT Connect using an S VIDEO cord (not supplied). You will enjoy high quality images. to CONTROL S IN CONTROL S IN DVD recorder VHF/UHF IN DIGITAL OUT LINE IN PCM/DTS/DOLBY DIGITAL R-AUDIO-L COAXIAL OUT CONTROL S IN OPTICAL LINE OUT S VIDEO R-AUDIO-L VIDEO 1 1 3 2 S VIDEO Y ~ AC IN VIDEO PB PR COMPONENT VIDEO OUT CONTROL S LINE OUT R-AUDIO-L S VIDEO VIDEO to LINE OUT (S VIDEO) 1 or 2 1 Control S cord (not supplied) 2 INPUT S VIDEO cord (not supplied) : Signal flow 18 Step 3: Connecting the Video Cords S VIDEO TV, projector, or AV amplifier (receiver) : Signal flow TV Note Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In the case of 480 progressive scan picture problems, it is recommended that the user switch the connection to the ‘standard definition’ output. If there are questions regarding our TV set compatibility with this model 480p DVD recorder, please contact our customer service center. Step 4: Connecting the Audio Cords Select the connection that best suits your system. Be sure to read the instructions for the components you wish to connect. Basic Hookups and Settings Connection Your setup A TV • Surround effects: Dynamic, Wide B Stereo amplifier (receiver) and two speakers • Surround effects: Standard MD deck/DAT deck • Surround effects: None C AV amplifier (receiver) having a Dolby Surround (Pro Logic) decoder*1 and 3 to 6 speakers • Surround effects: Dolby Surround (Pro Logic) D AV amplifier (receiver) with a digital input jack having a Dolby Digital or DTS*2 decoder and 6 speakers • Surround effects: Dolby Digital (5.1ch), DTS (5.1ch) *1 Manufactured under license from Dolby laboratories. “Dolby,” “Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories. *2 “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc. ,continued Step 4: Connecting the Audio Cords 19 Connecting to your TV A This connection will use your TV’s speakers for sound. DVD recorder VHF/UHF IN DIGITAL OUT LINE IN PCM/DTS/DOLBY DIGITAL R-AUDIO-L COAXIAL OUT CONTROL S IN OPTICAL LINE OUT S VIDEO VIDEO R-AUDIO-L 1 1 3 2 ~ Y S VIDEO AC IN VIDEO PB PR COMPONENT VIDEO OUT A If your stereo amplifier (receiver) only has audio input jacks L and R, use B-1 . If your amplifier (receiver) has a digital input jack, or when connecting to an MD deck or DAT deck, use B-2 . In this case, you can also connect the recorder directly to the MD deck or DAT deck without using your stereo amplifier (receiver). to LINE OUT (R-AUDIO-L) 1 or 2 LINE OUT R-AUDIO-L Connecting to a stereo amplifier (receiver) and 2 speakers/Connecting to an MD deck or DAT deck B S VIDEO VIDEO DVD recorder 1 VHF/UHF IN 2 DIGITAL OUT LINE IN PCM/DTS/DOLBY DIGITAL R-AUDIO-L COAXIAL OUT TV CONTROL S IN OPTICAL LINE OUT S VIDEO VIDEO R-AUDIO-L 1 1 3 2 S VIDEO ~ Y AC IN VIDEO PB PR COMPONENT VIDEO OUT (yellow) (yellow)* INPUT VIDEO (white) B-2 (white) L Coaxial digital cord (not supplied) B-1 LINE OUT DIGITAL OUT PCM/DTS/DOLBY DIGITAL (red) (red) AUDIO R-AUDIO-L COAXIAL S VIDEO VIDEO 1 R Audio/video cord (supplied) 2 OPTICAL or to DIGITAL OUT (COAXIAL or OPTICAL) to LINE OUT (R-AUDIO-L) 1 or 2 : Signal flow * The yellow plug is used for video signals (page 18). Optical digital cord (not supplied) (red) Stereo audio cord (not supplied) z Hint When connecting to a monaural TV, use a stereo-mono conversion cord (not supplied). Connect the LINE OUT (R-AUDIO-L) 1/2 jacks to the TV’s audio input jack. (white) (red) (white) Note Do not connect the LINE IN (AUDIO L/R) jacks to your TV’s audio output jacks at the same time. to coaxial or optical digital input [Speakers] to audio input Stereo amplifier (receiver) Front (L) MD deck/DAT deck Front (R) : Signal flow z Hint For connection B-1 , you can use the supplied audio/video cord instead of using a separate stereo audio cord. 20 Step 4: Connecting the Audio Cords Connecting to an AV amplifier (receiver) having a Dolby Surround (Pro Logic) decoder and 3 to 6 speakers Connecting to an AV amplifier (receiver) with a digital input jack and 6 speakers If your AV amplifier (receiver) only has L and R audio input jacks, use C-1 . If your amplifier (receiver) has a digital input jack, use C-2 . You can enjoy Dolby Surround effects only when playing Dolby Surround audio or multi-channel audio (Dolby Digital) discs. If your AV amplifier (receiver) has a Dolby Digital or DTS decoder and a digital input jack, use this connection. Note that the surround sound effects of this recorder cannot be used with this connection. C D VHF/UHF IN DIGITAL OUT LINE IN PCM/DTS/DOLBY DIGITAL VHF/UHF R-AUDIO-L COAXIAL IN DIGITAL OUT LINE IN PCM/DTS/DOLBY DIGITAL R-AUDIO-L COAXIAL OUT CONTROL S IN OPTICAL LINE OUT S VIDEO R-AUDIO-L VIDEO 1 1 3 2 ~ Y S VIDEO OUT AC IN VIDEO CONTROL S IN OPTICAL LINE OUT S VIDEO VIDEO R-AUDIO-L 1 1 3 2 S VIDEO ~ Y AC IN VIDEO PB PR PB COMPONENT VIDEO OUT PR COMPONENT VIDEO OUT C-2 Coaxial digital cord (not supplied) D C-1 DIGITAL OUT PCM/DTS/DOLBY DIGITAL LINE OUT DIGITAL OUT PCM/DTS/DOLBY DIGITAL R-AUDIO-L COAXIAL to DIGITAL OUT (COAXIAL or OPTICAL) S VIDEO VIDEO COAXIAL 1 OPTICAL 2 OPTICAL or to DIGITAL OUT (COAXIAL or OPTICAL) or to LINE OUT (R-AUDIO-L) 1 or 2 Optical digital cord (not supplied) (white) (red) Optical digital cord (not supplied) Coaxial digital cord (not supplied) Stereo audio cord (not supplied) to optical digital input (red) to coaxial digital input (white) [Speakers] to coaxial or optical digital input [Speakers] Basic Hookups and Settings DVD recorder DVD recorder to audio input AV amplifier (receiver) having a decoder [Speakers] [Speakers] Amplifier (receiver) with Dolby Surround decoder Rear (L) Center Rear (R) Front (R) Front (R) Rear (L) Rear (R) Subwoofer Center Front (L) Front (L) : Signal flow Subwoofer Rear (mono) : Signal flow z Hint For correct speaker location, see the operating instructions of the connected components. Note z Hint For correct speaker location, see the operating instructions of the connected components. Note After you have completed the connection, be sure to set “Dolby Digital” to “Dolby Digital” and “DTS” to “On” under “Audio” in Easy Setup (page 24). Otherwise, no sound or a loud noise will come from your speakers. When connecting 6 speakers, replace the monaural rear speaker with a center speaker, 2 rear speakers, and a subwoofer. Step 4: Connecting the Audio Cords 21 Step 5: Connecting the Power Cord Connect the supplied power cord to the AC IN terminal of the recorder. Then plug the recorder and TV power cords into an AC outlet. After you connect the power cord, you must wait for a short while before operating the recorder. You can operate the recorder once the front panel display lights up and the recorder enters standby mode. If you connect additional equipment to this recorder (pages 29 to 30), be sure to connect the power cord after all connections are complete. Step 7: Easy Setup Follow the steps below to make the minimum number of basic adjustments for using the recorder. If you do not complete Easy Setup, it will appear each time you turn on your recorder. Make the settings below in the following order. OSD Language Setup m Clock Setup m Tuner and Channel Setup ~ m AC IN TV Type Setup to AC IN m Audio Connection Setup to AC outlet "/1 Step 6: Preparing the Remote You can control the recorder using the supplied remote. Insert two Size AA (R6) batteries by matching the 3 and # ends on the batteries to the markings inside the battery compartment. When using the remote, point it at the remote sensor on the recorder. RETURN </M/m/,, ENTER a Turn on the TV. b Press [/1. The recorder turns on and the power indicator on the front panel lights up in green. Notes • If the supplied remote interferes your other Sony DVD recorder or player, change the command mode number for this recorder. For details, see page 28. • Do not leave the remote in an extremely hot or humid place. • Do not drop any foreign object into the remote casing, particularly when replacing the batteries. • Do not expose the remote sensor to direct sunlight or a lighting apparatus. Doing so may cause a malfunction. • If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. 22 Step 5: Connecting the Power Cord c Switch the input selector on your TV so that the signal from the recorder appears on your TV screen. “Initial settings necessary to operate the DVD recorder will be made. You can change them later using Setup.” appears. If this message does not appear, select “Easy Setup” from “SETUP” in the System Menu to run Easy Setup. For details, see “Settings and Adjustments” on page 90. d Press ENTER. g Press M/m to select the item that matches the The Setup Display for selecting the language used in the on-screen display appears. EASY SETUP Language antenna connection you selected on page 16 (Hookup 1, 2, or 3). 1/5 Select the screen Language. EASY SETUP Tuner Preset 3/5 Select the way in which you will receive channels. English Antenna Français Cable ENTER. The Setup Display for clock setting appears. Basic Hookups and Settings e Press M/m to select a language, then press ◆ Hookup 1 and 2 • Antenna ◆ Hookup 3 • Cable EASY SETUP Clock 2/5 h Press ENTER. Select a method for setting the clock. If you select "Auto", this recorder will look for a time signal when you turn it off. The Tuner Preset function automatically starts searching for all of the receivable channels and presets them. Auto Manual EASY SETUP f Press M/m to select the item that matches the Tuner Preset Searching for receivable channels. Please wait. 3/5 Ch45 antenna connection you selected on page 16 (Hookup 1, 2, or 3). ◆ Hookup 1 and 3 Select “Auto,” then press ENTER. The recorder automatically sets the clock by searching for a channel that carries a time signal and sets your time zone and Daylight Saving Time (if applicable). To activate the Auto Clock function, turn off the recorder after finishing Easy Setup. If your clock is set to the wrong time zone or Daylight Saving Time, you can adjust these settings (page 93). If your clock cannot be set automatically, set the clock manually (page 93). ◆ Hookup 2 Select “Manual,” then press ENTER. Set the clock manually using </M/m/,, and press ENTER. EASY SETUP Clock 2/5 Set the time and date manually. Sun 9 / 14 / 2003 9 : 00 AM Once the clock is set, the Tuner Preset display appears. To set the channels manually, see page 92. After the Tuner Preset is finished, the Setup Display for selecting the aspect ratio of the connected TV appears. EASY SETUP TV Type 4/5 Select your TV screen type. 16 : 9 4 : 3 Letter Box 4 : 3 Pan Scan i Press M/m to select the setting that matches your TV type. ◆ If you have a 4:3 standard TV • 4:3 Letter Box Displays a wide picture with bands on the upper and lower sections of the screen. • 4:3 Pan Scan Automatically displays a wide picture on the entire screen and cuts off the sections that do not fit. ◆ If you have a wide-screen TV or a 4:3 standard TV with a wide-screen mode • 16:9 For details, see “TV type” on page 94. ,continued Step 7: Easy Setup 23 j Press ENTER. n Press M/m to select whether or not you wish The Setup Display for selecting the type of jack used to connect to your amplifier (receiver) appears. EASY SETUP Audio Connection 5/5 to send a DTS signal to your amplifier (receiver) and press ENTER. Choose the item that matches the audio connection you selected on pages 20 to 21 ( B through D ). B-2 Is this recorder connected to an amplifier (receiver)? Select the type of jack you are using. C-2 • Off Yes : LINE OUT(R-AUDIO-L) D Yes : DIGITAL OUT • On (only if the amplifier (receiver) has a DTS decoder) No o Press ENTER when “Finish” appears. k Press M/m to select the type of jack (if any) Easy Setup is finished. All connections and setup operations are complete. you are using to connect to an amplifier (receiver), then press ENTER. EASY SETUP Choose the item that matches the audio connection you selected on pages 20 to 21 ( A through D ). Easy Setup is finished A Finish • If you connect just a TV and nothing else, select “No,” then go to step 15. B-1 C-1 • Select “Yes: LINE OUT (R-AUDIO-L),” then go to step 15. B-2 C-2 D • Select “Yes: DIGITAL OUT.” The Setup Display for “Dolby Digital” appears. l Press M/m to select the type of Dolby Digital signal you wish to send to your amplifier (receiver). Choose the signal that matches the audio connection you selected on pages 20 to 21 ( B through D ). EASY SETUP Audio Connection 5/5 Dolby Digital D-PCM Dolby Digital B-2 C-2 • D-PCM D • Dolby Digital (only if the amplifier (receiver) has a Dolby Digital decoder) m Press ENTER. The Setup Display for selecting the type of DTS signal appears. EASY SETUP DTS On Off 24 Step 7: Easy Setup Audio Connection 5/5 To return to the previous step Press RETURN. z Hint If you want to run Easy Setup again, select “Easy Setup” in the Setup Display (page 100). Notes • If there are only a few channels in your area that carry time signals, setting the clock automatically may take up to about 20 minutes after the recorder turns off. If nothing happens even after you wait about 20 minutes, set the clock manually in “Clock” of “Settings” (page 93). • If you use the antenna connection Hookup 2 (page 17), make sure you leave the cable box on. • To record TV programs using the timer, you must set the clock accurately. Setting Up the VCR System Plus® c Press M/m to select “Settings,” then press ENTER. d Press M/m to select “Set VCR Plus+ Channels,” then press ENTER. The display for setting VCR Plus+ channels appears. Settings - Set VCR Plus+ Channels Guide CH -- TV CH -- ---- Basic Hookups and Settings Setting up your recorder involves coordinating the TV channel number (the number you turn to on your TV or recorder to watch a program) with the guide channel (the number that’s assigned to that channel in your TV program guide). To find the guide channel numbers, look at the “Channel Lineup Chart” in the program guide for your area that features VCR PlusCode numbers. Use the Channel Line-up Chart to check that the guide channel numbers match the TV channel your recorder receives. If not, you need to coordinate these numbers using the following procedure. If the guide and TV channel numbers are the same, you can skip this procedure. Channel list e Press M/m to select “Guide CH – TV CH,” then press ENTER. Settings - Set VCR Plus+ Channels Guide CH -- -- TV CH ---- -- -- f Enter the guide channel number assigned in the program guide using the number buttons, then press SET. Number buttons, SET Settings - Set VCR Plus+ Channels Guide CH 25 -- TV CH ---- -- 25 SYSTEM MENU </M/m/,, ENTER RETURN g Enter the TV channel number. Settings - Set VCR Plus+ Channels Guide CH 25 a Press SYSTEM MENU while the recorder is stopped. The System Menu appears. DVD Recorder Dual RW Compatible SYSTEM MENU TITLE LIST Plays/erases/edits recorded titles. -- TV CH ---- -- 36 ◆ For Hookup 1 or 3 (page 16) Enter the actual number on your TV (and recorder) using the number buttons, then press SET. ◆ For Hookup 2 (page 17) Enter the cable box output channel (usually 2, 3, or 4) using the number buttons, then press SET. TIMER TIMER LIST DV/D8 EDIT h Repeat steps 5 to 7 for each channel number that does not match. SETUP i Press SYSTEM MENU repeatedly to exit the b Press M/m to select “SETUP,” then press menu. ENTER. The Setup Display appears. SETUP Settings Press RETURN. Tuner Preset Video Set VCR Plus+ Channels Audio Clock Features To return to the previous step Language Options Easy Setup ,continued Setting Up the VCR Plus® System 25 To check the channel settings When displaying the “Set VCR Plus+ Channels” menu, press M/m to select “Channel List,” then press ENTER. The display lists the channels whose guide channel number is not as same as the TV channel number. Settings - VCR Plus+ Channel List Guide CH TV CH Guide CH Setting Up the Remote Page2 TV CH 2 - 21 45 - 18 4 - 32 53 - 5 6 - 9 -- - -- 10 - 121 -- - -- 11 - 13 -- - -- 25 - 36 -- - -- 28 - 2 -- - -- Close To go to the next page, press m. To return to the previous page, press M. You can control your TV with the supplied remote by adjusting the remote control’s signal. If you connected the recorder to an AV amplifier (receiver), you can also control the volume with the supplied remote. Notes • Depending on the connected unit, you may not be able to control your TV or AV amplifier (receiver) with some or all of the buttons below. • If you enter a new code number, the code number previously entered will be erased. • When you replace the batteries of the remote, the code number may be reset to the default setting. Set the appropriate code number again. Controlling TVs with the remote TV/DVD switch "/1 CH +/– Number buttons, SET VOL +/– TV/VIDEO WIDE MODE a Slide the TV/DVD switch to TV. b Hold down [/1. c Enter your TV’s manufacturer code (see “Code numbers of controllable TVs” below) using the number buttons. d Release [/1. When the TV/DVD switch is set to TV, the remote performs the following: 26 Setting Up the Remote [/1 Turns your TV on or off VOL +/– Adjusts the volume of your TV CH +/– Selects the channel on your TV WIDE MODE Switches to or from the wide mode of a Sony wide-screen TV TV/VIDEO Switches your TV’s input source Number buttons and SET Selects the channel on your TV Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV. Code number Sony 01 (default) Akai 04 AOC 04 Centurion 12 Coronado 03 Curtis-Mathes 12 Daytron 12 Emerson 03, 04, 14 Fisher 11 General Electric 06, 10 Gold Star 03, 04, 17 Hitachi 02, 03 J.C.Penney 04, 12 JVC 09 KMC 03 Magnavox 03, 08, 12 Marantz 04, 13 MGA/Mitsubishi 04, 12, 13, 17 NEC 04, 12 Panasonic 06, 19 Philco 03, 04 Philips 08, 21 Pioneer 16 Portland 03 TV/DVD switch "/1 Number buttons, SET Basic Hookups and Settings Manufacturer Controlling the volume of your AV amplifier (receiver) with the remote VOL +/– a Slide the TV/DVD switch to DVD. b Hold down [/1, and enter the manufacturer code (see the table below) for your AV amplifier (receiver) using the number buttons. c Release [/1. The VOL +/– buttons control the AV amplifier’s volume. ◆ If you want to control the TV’s volume Slide the TV/DVD switch to TV. Proscan 10 z Hint Quasar 06, 18 Radio Shack 05, 14 If you want to control the TV’s volume even when the TV/DVD switch is set to DVD, repeat the steps above and enter the code number 90 (default). RCA 04, 10 Sampo 12 Samsung 03, 12, 20 Sanyo 11, 14 Scott 12 Code numbers of controllable AV amplifiers (receivers) If more than one code number is listed, try entering them one at a time until you find the one that works with your AV amplifier (receiver). Sears 07, 10, 11 Sharp 03, 05, 18 Manufacturer Code number Sylvania 08, 12 Sony 80, 88, 89, 91 Teknika 03, 08, 14 Denon 84, 85, 86 Toshiba 07 Kenwood 92, 93 Wards 03, 04, 12 Onkyo 81, 82, 83 Yorx 12 Pioneer 99 Zenith 15 Sansui 87 Technics 97, 98 Yamaha 94, 95, 96 ,continued Setting Up the Remote 27 If you have a Sony DVD player or more than one Sony DVD recorder d Press M/m to select “Command Mode,” then press ENTER. SETUP If the supplied remote interferes with your other Sony DVD recorder or player, set the command mode number for this recorder and the supplied remote to one that differs from the other Sony DVD recorder or player. The default command mode setting for this recorder and the supplied remote is DVD3. Settings Format Disc : Selectable Video Dimmer : Bright Audio Auto Display : On Command Mode : DVD3 DVD1 Features Options Factory Setup DVD2 DVD3 Easy Setup e Press M/m to select the Command mode (DVD1, DVD2, or DVD3), then press ENTER. f Slide the COMMAND MODE switch on the remote so it matches the mode you selected above. To return to the previous step SYSTEM MENU Press RETURN. M/m, ENTER RETURN COMMAND MODE a Press SYSTEM MENU. The System Menu appears. b Press M/m to select “SETUP,” then press ENTER. SETUP Settings Tuner Preset Video Set VCR Plus+ Channels Audio Clock Features Language Options Easy Setup c Press M/m to select “Options,” then press ENTER. SETUP Settings Format Disc : Selectable Video Dimmer : Bright Audio Auto Display : On Command Mode : DVD3 Features Options Factory Setup Easy Setup 28 Setting Up the Remote Connecting a VCR or Similar Recording Device to the LINE Jacks How to connect to record on other equipment Connect a VCR or similar recording device to the LINE OUT jacks of this recorder. VCR, etc. INPUT AUDIO R VIDEO S Video L Audio/video cord (not supplied) S VIDEO cord (not supplied) How to connect to record on this recorder Connect a VCR or similar recording device to the LINE IN jacks of this recorder. See “Recording from connected equipment” on page 88. LINE OUT S VIDEO R-AUDIO-L VIDEO 1 Basic Hookups and Settings You can use this recorder as the source player or as the recording deck. After disconnecting the recorder’s power cord from an AC outlet, connect a VCR or similar recording device to the LINE jacks of this recorder. Use the DV IN jack on the front panel if the equipment has a DV output jack (i.LINK jack) (page 75). See also the instruction manual supplied with the connected equipment. VCR, etc. 2 OUTPUT AUDIO VIDEO R S Video L DVD recorder to LINE OUT 1 or 2 VHF/UHF IN DIGITAL OUT LINE IN PCM/DTS/DOLBY DIGITAL R-AUDIO-L COAXIAL OUT CONTROL S IN OPTICAL LINE OUT S VIDEO R-AUDIO-L VIDEO 1 1 3 2 S VIDEO Y ~ AC IN VIDEO PB PR COMPONENT VIDEO OUT Audio/video cord (not supplied) : Signal flow S VIDEO cord (not supplied) Notes • If you pass the recorder signals via the VCR, you may not receive a clear image on the TV screen. LINE IN S VIDEO R-AUDIO-L VIDEO 1 DVD recorder 3 TV • Do not connect the yellow LINE IN (VIDEO) jack when using an S VIDEO cord (not supplied). DVD recorder to LINE IN 1 or 3 VCR VHF/UHF IN DIGITAL OUT LINE IN PCM/DTS/DOLBY DIGITAL R-AUDIO-L COAXIAL OUT CONTROL S IN OPTICAL LINE OUT S VIDEO R-AUDIO-L VIDEO S VIDEO Y ~ AC IN VIDEO 1 1 PB 3 2 PR COMPONENT VIDEO OUT : Signal flow z Hint You can also use the LINE 2 IN jacks on the front panel of the recorder (page 88). Notes • Do not connect the yellow LINE IN (VIDEO) jack when using an S VIDEO cord (not supplied). • Pictures containing copy protection signals that prohibit any copying cannot be recorded. Connecting a VCR or Similar Recording Device to the LINE Jacks 29 Connecting to a Satellite Receiver or a Cable Box Connect a satellite receiver, digital cable box, or a cable box to this recorder using the LINE IN 1/3 jacks. Disconnect the recorder’s AC power cord from an AC outlet when connecting the box. To record on this recorder, see page 88. To use the Synchro Rec function, see below. Satellite receiver, etc. OUTPUT AUDIO VIDEO R L Audio/video cord (not supplied) LINE IN S VIDEO R-AUDIO-L VIDEO 1 3 to LINE IN 1 or 3 DVD recorder VHF/UHF IN DIGITAL OUT LINE IN PCM/DTS/DOLBY DIGITAL R-AUDIO-L COAXIAL OUT CONTROL S IN OPTICAL LINE OUT S VIDEO VIDEO R-AUDIO-L S VIDEO Y ~ AC IN VIDEO 1 1 PB 3 2 PR COMPONENT VIDEO OUT : Signal flow If you want to use the Synchro Rec function Connect a satellite receiver to LINE IN 1 jacks of this recorder. See “Recording from External Equipment with a Timer (Synchro Rec)” on page 47. Refer to your satellite receiver’s instructions for more information. Notes • Synchro-Recording does not work with some boxes. For details, refer to the box’s operating instructions. • When connecting the LINE IN jacks to the cable box, be sure to also connect the recorder’s antenna to the cable box. 30 Connecting to a Satellite Receiver or a Cable Box Guide to Displays Operating the Recorder The recorder uses the following four types of displays for most operations: System Menu, Title List, TOOLS, and Sub-menu. It also has a Disc Information display for checking the status of the inserted disc, and an on-screen keyboard that enables you to label a title or disc. Operating the Recorder The recorder’s overall operation is simple. Generally, most operations can be performed by pressing only </M/m/,, and ENTER. Once you know the common procedure, you will find the recorder easy to operate. Number buttons, SET TITLE LIST SYSTEM MENU TOOLS CURSOR MODE ZOOM +/– RETURN </M/m/,, ENTER System Menu The System Menu appears when you press SYSTEM MENU, and provides entries to all of the recorder’s main functions. SYSTEM MENU TITLE LIST DVD Recorder Dual RW Compatible Plays/erases/edits recorded titles. TIMER TIMER LIST DV/D8 EDIT SETUP 1 TITLE LIST (page 53, 64): Turns on the Title List menu, which shows recorded titles on the disc. 2 TIMER (page 40): Allows you to set a new timer recording setting. 3 TIMER LIST (page 42): Turns on the Timer List menu, which allows you to check, change, or cancel timer settings. • Guide to Displays . . . . . . . . . . . . . . . . .page 31 • How to Use the Displays . . . . . . . . . . .page 33 • How to Enter Characters . . . . . . . . . . .page 34 4 DV/D8 EDIT (page 79): Activates the DV Edit function, which allows you to record and edit the contents of a DV/Digital8 format tape. 5 SETUP (page 91): Turns on the Setup Display, which allows you to set up the recorder to suit your preferences. ,continued Guide to Displays 31 About the types of Title List menus Title List The recorder uses list displays for some operations. The most frequently used is the Title List menu. The Title List menu appears when you press TITLE LIST or when you select “TITLE LIST” from the System Menu, and displays all of the titles on the disc. To show the list in greater details (zoom), press ZOOM+. To return to the previous display, press ZOOM–. The appearance of the Title List menu differs according to the disc type and recording format. ◆For DVD+RWs, DVD-Rs, DVD-RWs (Video mode): The Title List menu appears and displays the titles on the disc. ◆For DVD-RWs (VR mode): The Title List (Original) or Title List (Playlist) menu appears and displays the Original or Playlist titles on the disc. The “PLAYLIST” indicator lights up on the front panel display when the Title List (Playlist) menu is selected. Standard Title List -RW.VR TITLE LIST My Movies ORIGINAL 1.5/4.7GB 1 2ch 1:00PM - 2:00PM 9/15 Date 2 5ch 8:00PM - 9:00PM 9/17 Number 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 5 25ch 8:00PM - 8:30PM 10/15 6 L2 9:00PM - 9:30PM 10/19 7 8ch 9:00PM - 9:30PM 10/26 8 125ch 10:00AM - 10:30AM 10/28 Sort Title “Zoomed” Title List -RW.VR TITLE LIST Sort Date Number Title My Movies ORIGINAL To switch the Title List menu for a DVD-RW (VR mode) The recorder displays either the Original or Playlist Title List. Follow the steps below. 1 Press TITLE LIST. The Title List menu appears. 2 Press TOOLS. The TOOLS menu appears. 3 Press M/m to select either “Original” or “Playlist,” whichever is not displayed, then press ENTER. The display switches to the selected Title List menu. 1.5/4.7GB 1 2ch 1:00PM - 2:00PM To scroll the list display by page (Page mode) 2 5ch 8:00PM - 9:00PM 3 12ch 9:00AM - 9:30AM Press CURSOR MODE while the list display is turned on. The display enters Page mode. Each time you press M/m, the entire Title List changes to the next/previous page of titles. To return to the Cursor mode, press CURSOR MODE again. 2ch Mon 9/15 1:00PM( 1H00M) SP 5ch Wed 9/17 8:00PM( 1H00M) SLP Thu 9/25 9:00AM( 0H30M) 4 3ch 12ch EP 8:00PM - 8:30PM 3ch Thu 9/25 8:00PM( 0H30M) SLP Notes 1 Sort buttons (page 54): Sorts the title order. 2 Zooming indicator (page 54): Shows the current zoom status. 3 Disc name (page 72) 4 Disc space (remainder/total) 5 Title information (page 54): Displays the title number, title name, and recording date. 6 Scroll bar: Appears when all the titles do not fit on the list. To view the hidden titles, press M/m. • When you turn off the list display, the Page mode is canceled. • When all the titles on the disc fit on a single page, you cannot select the Page mode. TOOLS The TOOLS menu appears when you press TOOLS, and displays options applicable to the entire disc or recorder. Example 1: When you press TOOLS while the Title List menu is turned on. -RW.VR Options for the disc or menu TITLE LIST Close Sort DatePlaylist 1.5/4.7GB 1:00PM- 2:00PM 9/15 2 5ch 8:00PM- 9:00PM 9/17 12ch 9:00AM- 9:30AM 9/25 Create Playlist 4 3ch 8:00PM- 8:30PM 9/25 Disc Info. 5 25ch 8:00PM- 8:30PM 10/15 3 7 Title’s thumbnail picture (page 54) My Movies 2ch Number Erase Titles Title ORIGINAL 1 TOOLS 6 L2 9:00PM- 9:30PM 10/19 7 8ch 9:00PM- 9:30PM 10/26 8 125ch 10:00AM-10:30AM 10/28 Notes • The letters that cannot be displayed are replaced with “*”. • The Title List does not appear when you play DVD VIDEOs, CDs, CD-Rs, or CD-RWs. • The Title List may not appear for discs created on other DVD recorders. • On this model, 1 GB is equivalent to 1 billion bytes. Example 2: When you press TOOLS while a DVD is playing. Close Options for the disc or picture Stop Title Search Chapter Search Time Search TOOLS 32 Guide to Displays How to Use the Displays Sub-menu The sub-menu appears when you select an item from the displayed list menu and press ENTER. The sub-menu displays options applicable only to the selected item. Example: The Title List menu -RW.VR TITLE LIST ORIGINAL Use the displays in the following way. The procedure is common to many of the operations. My Movies 1.5/4.7GB Close 2ch 1:00PM - 2:00PM Date 2 5ch 8:00PM - 9:00PM 9/17 Number 3 12ch 9:00AM - 9:30AM Erase9/25 4 3ch 8:00PM - 8:30PM Protect Title 9/25 5 25ch 8:00PM - 8:30PM 6 L2 9:00PM - 9:30PM 7 8ch 9:00PM - 9:30PM 10/26 8 125ch 10:00AM - 10:30AM 10/28 Title 9/15 Play Play From Start Title Name 10/15 Options for the selected item a Press SYSTEM MENU. The System Menu appears with entries to the main functions. Set Thumbnail 10/19 A-B Erase b Press M/m to select a function, then press ENTER. The display for the selected function appears. Example: When “TITLE LIST” is selected. -RW.VR TITLE LIST ORIGINAL My Movies 1.5/4.7GB 1 2ch 1:00PM - 2:00PM 9/15 Date 2 5ch 8:00PM - 9:00PM 9/17 Number 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 5 25ch 8:00PM - 8:30PM 10/15 6 L2 9:00PM - 9:30PM 10/19 7 8ch 9:00PM - 9:30PM 10/26 8 125ch 10:00AM - 10:30AM 10/28 Sort Title Operating the Recorder 1 Sort ◆ Using the TOOLS menu Use the TOOLS menu to display options for the entire disc. A Press TOOLS. The TOOLS menu appears. B Press M/m to select the option, then press ENTER. ◆ Using the sub-menu The sub-menu displays options for a specific title. A Press M/m to select the title on the list, then press ENTER. The sub-menu appears. B Press M/m to select the option, then press ENTER. c Press RETURN repeatedly to turn off the list display. To return to the previous display Press RETURN. How to Use the Displays 33 ◆ To erase a character How to Enter Characters A Press </M/m/, to move the cursor to the input row. B Press </, to move the cursor to the right of the character you want to erase. C Press </M/m/, to select “Back,” then press ENTER. You can label a title, disc, or program by entering characters. You can enter up to 64 characters for a title/disc/program name, but the actual number of characters displayed in the menus such as the Title List will vary. When the display for entering characters appears, follow the steps below. ◆ To insert a character A Press </M/m/, to move the cursor to the input row. a Press </M/m/, to move the cursor to the B Press </, to move the cursor to the right of the point where you want to insert a character. right of the screen and select “A” (uppercase), “a” (lower-case), or “Symbol,” then press ENTER. C Press </M/m/, to select the character you want to insert, then press ENTER. The characters of the selected type are displayed. ◆ To erase all the characters Press </M/m/, to select “Clear All,” then press ENTER. Example: Input Title Name d Press </M/m/, to select “Finish,” then Input Title Name 25ch 1:00PM - 2:00PM press ENTER. "A" - 1 2 A B C 2 3 D E F 3 4 G H I 4 1 . 5 J , K L 6 M N O 6 Back 7 P Q R S Clear All 8 T U V 8 9 W X Y Z Space 5 0 To cancel the setting, select “Cancel.” "a" 7 Symbol To use the number buttons 9 0 Cancel You can also use the number buttons to enter characters. Finish 1 In step 2 above, press the number buttons repeatedly to select the character you want to enter. Example: Press the number 3 button once to enter “D.” Press the number 3 button three times to enter “F.” 2 3 Select the next character, or press SET. 4 Press </M/m/, to select “Finish,” then press ENTER. b Press </M/m/, to select a character you want to enter, then press ENTER. The selected character appears at the top of the display. Input Title Name K "A" - 1 2 A B C 2 3 D E F 3 4 G H I 4 5 J L 5 1 . , K 6 M N O 6 Back 7 P Q R S Clear All 8 T U V 8 9 W X Y Z Space 0 "a" 7 Symbol 9 Cancel 0 Finish To enter a letter with an accent mark, select an accent followed by the letter. Example: Select “ ` ” and then “a” to enter “à.” To insert a space between the characters, select “Space.” c Repeat steps 1 and 2 to enter all the characters for the name. Input Title Name Kids "A" 1 . , - 1 2 A B C 2 3 D E 3 F 4 G H I 4 5 J L 5 K 6 M N O 6 Back 7 P Q R S Clear All 8 T U V 8 9 W X Y Z Space 0 0 "a" 7 Symbol 9 Cancel Finish 34 How to Enter Characters Repeat steps 1 and 2 to enter all of the characters for the name. Before Recording This section covers the basics of DVD recording, and the available methods for setting the timer. This recorder can record on various discs. Before you record, read the following and select the disc type according to your needs. Recordable discs This recorder can record on the following discs. ◆Disc type Recording/Timer Recording Recording/ Timer Recording DVD-RW*1 Ver. 1.1 Ver. 1.1 with CPRM*2 DVD+RW*1 DVD-R*1 Ver. 2.0 *1 “DVD-RW,” “DVD+RW,” and “DVD-R” are trademarks. *2 CPRM (Content Protection for Recordable Media) is a coding technology that protects copyrights for images. DVD-RWs and DVD+RWs are rewritable. DVD-Rs are nonrewritable. The recorder cannot record on the following discs: • 8 cm discs • DVD+R • DVD-RW (Ver 1.0) • DVD-RAM • CD-R/CD-RW Notes • Before Recording . . . . . . . . . . . . . . . . .page 35 • Recording TV programs . . . . . . . . . . . . . . . .page 38 • The following type of high-speed discs can be used for recording: up to 2×-speed DVD-RWs (Revision 1.0), up to 4×-speed DVD-Rs (Revision 1.0), or up to 4×-speed DVD+RWs. Note that high-speed discs will not record at higher speed. You cannot record on the disc if it is not 1×-speed compatible. • Use a disc with CPRM to record Copy-Once TV programs (page 36). • It is recommended that you use discs with “For Video” printed on their packing. • You cannot add new recordings to DVD-Rs and DVD-RWs (Video mode) that contain recordings made on other DVD recorders. • In some cases, you may not be able to add new recordings to DVD+RWs that contain recordings made on other DVD recorders. If you do add a new recording, note that this recorder will rewrite the DVD menu. If the disc contains PC data unrecognizable by this recorder, the data will be erased. • Timer Recording . . . . . . . . . . . . . . . . . . . . . .page 40 • Adjusting the Recording Picture Quality and Size . . .page 46 • Recording from External Equipment with a Timer (Synchro Rec) . . . . . . . . . . . . . . . . . . . . . .page 47 ,continued Before Recording 35 About recording formats When you insert an unused disc, the recorder automatically starts formatting. Since available functions differ depending on the disc type, select the disc that best suits your needs using the chart below. You can preset the format for unused DVD-RWs in Options Setup. When “Format Disc” is set to either “VR” or “Video” (page 99), the recorder starts formatting in the selected mode without asking for confirmation. Select “Selectable” if you want to select the mode each time you insert an unused DVD-RW. Differences between the disc types See pages in parentheses for details. Disc type Characteristics Unrecordable pictures Pictures with copy protection cannot be recorded on this recorder. When the recorder receives a copy guard signal while recording, the recorder stops recording and a message appears on your TV screen. About pictures with Copy Control Signals Broadcasts that contain Copy Control Signals may have one of the following three signal types, Copy-Free, Copy-Once, and Copy-Never. This recorder limits the recording according to copy protection signal as shown below. If you want to record a Copy-Once program, use a DVD-RW with CPRM in VR mode. ◆Available recording options – Automatically creates chapters at specified intervals (page 97) – Simple editing (erasing titles/changing title name) (page 64) – Creates chapters manually or automatically (page 67) – Various editing options using a created Playlist (page 67) – Records Copy-Once programs provided that the disc has CPRM Notes • To play a recorded disc on other DVD equipment, you need to finalize the disc. For details on finalizing, see page 73. • You cannot mix the two formats on one DVD-RW. To change the disc’s format, reformat the disc (page 74). Note that the disc’s contents will be erased after reformatting. Recording mode While the recorder is stopped, you can select one of six recording modes by pressing REC MODE repeatedly for the desired recording time and picture quality. The picture quality generally improves as the recording time decreases. Recording mode Recording time (minute) HQ 60 HSP 90 SP (Standard mode) 120 LP 180 EP 240 SLP 360 Notes • The recording times are an estimate and actual times may differ. • Situations below may cause slight inaccuracies with the recording time. – Recording a program with poor reception, or a program or video source of low picture quality – Recording on a disc that has already been edited – Recording only a still picture or just sound 36 Before Recording CopyFree CopyOnce CopyNever DVD-RW (Ver.1.1) a — — DVD-RW (Ver.1.1 with CPRM VR mode Video mode a a a* — — — DVD+RW a — — DVD-R (Ver.2.0) a — — * The recorded disc can be played only on CPRM compatible equipment. Checking the available disc space (Disc Info.) When recording on a used disc, make sure that there is enough disc space for recording. With DVD-RWs or DVD+RWs, you can free up disc space by erasing titles. ◆How programs are recorded on a DVD-R A new program is recorded on the last space [a] only. Check that the remaining disc space is large enough for the recording. Erasing “B” does not free up any space a A a Press TOOLS while the disc is in the recorder. The TOOLS menu appears. b Press M/m to select “Disc Info.,” then press ENTER. C New recording You cannot free up disc space on a DVD-R. Erasing a title will only hide the title name in the Title List menu. The erased titles will still take up space on the disc. ◆How programs are recorded on a DVD-RW (VR mode) A program is recorded on the free disc space [a]. Check that the total remaining disc space is large enough for recording. Erasing “B” frees up more space Example: DVD-RW (VR mode) A B Disc Information a Close Media DVD-RW Title no. Original 3 / Playlist 2 Format New recording Protect Disc New recording (continued) Finalize Erase All 9/15/2003 ~ 10/28/2003 HSP : 0H45M EP : 2H00M C Disc Name VR Protected Not Protected HQ : 0H30M Remainder LP : 1H30M a A DiscName Movie Date C Recording/Timer Recording The Disc Information display appears. Items in the display differ depending on the disc type or recording format. Note that the remaining disc space indicator is an estimate and actual available space may differ. B SP : 1H00M SLP : 3H00M 2. 3 / 4. 7GB Format 1 Disc Name ◆To free up disc space You can free up disc space by erasing titles. The original title used for a Playlist cannot be erased. To erase a title, see page 65. To erase multiple titles, see page 65. 2 Media: Disc type 3 Format: Recording format type (DVD-RW only) 4 Title no.: Total number of titles ◆How programs are recorded on a DVD-RW (Video mode) or DVD+RW The recorder searches for the largest block of space [a] and records there. Check that there is a continuous free block large enough for the recording. If not, the recording will stop. 5 Protected: Indicates whether protection is set (DVD-RW in VR mode only) Erasing “B” and “C” creates a block of free space A 6 Date: Dates when the oldest and the most recent titles are recorded 8 Disc setting buttons • Disc Name: Labels the disc (page 72) • Protect Disc: Protects the disc (DVD-RW in VR mode only) (page 72) • Finalize: Finalizes the disc/Creates a DVD menu (page 73) • Unfinalize: Unfinalizes the disc if it has already been finalized (DVD-RW in VR mode only) (page 73) • Erase All: Erases all titles on the disc (page 73) • Format: Reformats the disc (page 74) C D a D A New recording 7 Continuous Rem. Time/Remainder: • The longest continuous recording time in each of the recording modes (approximate) • Disc space bar (approximate) • Remaining disc space/total disc space (approximate) B ◆To check or free up disc space For DVD-RWs (Video mode) and DVD+RWs only, you can check free disc space and title location, and also erase titles using the Disc Map display (see below). z Hint You can erase all of the disc’s titles (other than protected titles) at once (page 73). Notes • When you erase titles, the title order may change depending on the disc type or format. • After finalizing, you cannot record further on a DVD-RW (Video mode) or DVD-R. ,continued Before Recording 37 To free up disc space using the Disc Map display (DVD-RWs in Video mode, DVD+RWs only) Recording TV programs The Disc Map display in the TOOLS menu allows you to check the disc status and erase titles on the disc. 1 Press TITLE LIST while the disc is in the recorder. 2 3 Press TOOLS. Press M/m to select “Disc Map” from the TOOLS menu, then press ENTER. The Disc Map display appears. ◆ To check free disc space Press </, to select an open space. The remaining space and the longest recording time in each of the recording modes appears. Before you start… • Check that the disc has enough available space for the recording (page 37). • Adjust the recording picture quality and picture size if necessary (page 46). Z OPEN/CLOSE Disc Map }/1 CH +/– Empty HQ[ 0H30M] LP [ 1H30M] HSP[ 0H45M] EP[ 2H00M] SP[ 1H00M] 2.3GB SLP[ 3H00M] Selected open space Number buttons, SET TV/VIDEO Erase Cancel DISPLAY TOOLS ◆ To free up disc space by erasing a title using the Disc Map </M/m/,, ENTER A Press </, to select the title you want to erase, then press ENTER. The title is selected. Disc Map 2 5ch X REC PAUSE z REC x REC STOP REC MODE 8:00PM - 9:00PM Wed 9/17 8:00PM( 1H00M) TIME/TEXT SP 0.6GB INPUT SELECT Selected title Erase Cancel To cancel the selection, press ENTER again. Repeat step 1 to erase multiple titles. B Press m to select “Erase,” then press ENTER. The display asks for confirmation. C Press </, to select “OK.” All of the selected titles are erased, freeing up disc space. If you want to change your selection, select “Change.” D Press RETURN repeatedly to turn off the Title List menu. Note You cannot erase a title during playback or recording. 38 Recording TV programs a Press }/1. The recorder turns on and the power indicator on the front panel lights up in green. b Turn on the TV, and switch the input selector on your TV so that the signal from the recorder appears on the TV screen. ◆ When using an amplifier (receiver) Turn on the amplifier (receiver) and select the appropriate channel so that you can hear sound from the recorder. c Press Z OPEN/CLOSE, and place a recordable disc on the disc tray. Notes • After pressing z REC, it may take a short while to start recording. • While recording or during recording pause, you cannot change the recording mode. • If there is a power failure, the program you are recording may be erased. • When you use Hookup 2 (page 17), you cannot watch a cable TV program while recording another cable TV program. With the recording side facing down Using the Quick Timer function d Press Z OPEN/CLOSE to close the disc tray. e Press CH +/– to select the channel or input You can set the recorder to record in 30 minute increments by pressing just the z REC button. Press z REC repeatedly to set the duration time. Each press advances the time in 30 minute increments. The maximum duration is six hours. 0:30 1:00 5:30 6:00 (normal recording) source you want to record. f Press REC MODE repeatedly to select the recording mode. Each time you press the button, the display changes on the TV screen as follows: HQ HSP SP LP EP SLP For more details of the recording mode, see page 36. g Press z REC. Recording starts. Recording continues until you stop the recording or the disc is full. To stop recording Press x REC STOP. Note that it may take a few seconds for recording to stop. To pause recording Press X REC PAUSE. To restart recording, press the button again. The time counter decreases minute by minute to 0:00, then the recorder stops recording (power does not turn off). Even if you turn off the recorder during recording, the recorder continues to record until the time counter runs out. Recording/Timer Recording Wait until “LOAD” disappears from the front panel display. If you use an unused DVD, formatting starts automatically. When using an unused DVD-RW, select the recording format, VR or Video. To cancel the Quick Timer Press z REC repeatedly until the counter appears in the front panel display. The recorder returns to normal recording mode. Recording a stereo program and SAP The recorder automatically receives and records a stereo program and SAP. ◆Stereo programs When a stereo program is received, the “STEREO” indicator lights up on the front panel display. If there is noise in the stereo program, set “Auto Stereo” in Audio Setup to “Off” (page 95). The sound will be recorded in monaural but with less noise. ◆SAP (Second Audio Program) When a SAP (Second Audio Program) is received, the “SAP” indicator lights up on the front panel display. To record only SAP sound, set “Tuner Audio” in Audio Setup to “SAP” (page 95). To watch another TV program while recording Set the TV to TV input using the TV/VIDEO button. z Hints • You can also start and stop recording using the TOOLS menu. Press TOOLS and select “Record” or “Rec Stop,” then press ENTER. • You can stop recording from the Title List menu as well. Select the title you are currently recording and press ENTER. Then select “Rec Stop” from the sub-menu. • If you do not want to watch TV while recording, you can turn off the TV. When using a cable box, make sure to leave it on. • To select a channel, you can also use the number buttons and SET button in step 5 above. • If you record from equipment connected to the recorder’s input jack, you can also use the INPUT SELECT button to select “L1,” “L2,” “L3,” or “DV” in step 5. For details, see “Recording from connected equipment” (page 88). • You can also select the recording mode using the TOOLS menu (page 46). ,continued Recording TV programs 39 Checking the disc status while recording Timer Recording You can check the recording information such as recording time or disc type. a Press DISPLAY twice during recording. The recording information appears. DVD-RW VIDEO SP 1:23:45 You can set the timer for a total of 30 programs up to one month in advance. There are two setting methods: the manual setting and VCR Plus+ setting. • Standard: Set the date, time, and channel of the program manually. • VCR Plus+: Enter the PlusCode number designated for each TV program (page 44). 1 Disc type/format Before you start… 2 Recording status • Check that the disc has enough available space for the recording (page 37). • Adjust the recording picture quality and picture size if necessary (page 46). 3 Recording mode 4 Recording time b Press DISPLAY to turn off the display. Setting the timer manually (Standard) Creating chapters in a title The recorder can automatically divide a recording (a title) into chapters by inserting chapter marks at 6 or 15 minute intervals during recording. Select the interval, “6Min” (default) or “15Min” in “Auto Chapter” of Features Setup (page 97). Z OPEN/CLOSE "/1 z Hint You can make chapters manually when playing DVD-RWs (VR mode). For details, see page 67. Notes • If “Auto Chapter” is set to “Off” in Features Setup, no chapters are automatically created. • When no more chapter marks can be added, you may not be able to make additional recordings or edit the disc. [TIMER] SYSTEM MENU RETURN TOOLS </M/m/,, ENTER x REC STOP a Press }/1. b Turn on the TV, and switch the input selector on your TV so that the signal from the recorder appears on the TV screen. ◆ When using an amplifier (receiver) Turn on the amplifier (receiver) and select the appropriate channel so that you can hear sound from the recorder. c Press Z OPEN/CLOSE, and place a recordable disc on the disc tray. 40 Timer Recording d Press Z OPEN/CLOSE to close the disc tray. Wait until “LOAD” disappears from the front panel display. If you use an unused DVD, formatting starts automatically. When using an unused DVD-RW, select the recording format, VR or Video. h Press RETURN to turn off the Timer List, or press [TIMER] and repeat from step 5 to enter additional timer settings. Unlike a VCR, there is no need to turn off the recorder before the timer recording starts. To stop recording during timer recording e Press [TIMER]. Press x REC STOP. The Timer programming (Standard) menu appears. If the timer settings overlap Timer - Standard Overlapped timer settings are shown as follows. Set the timer manually. Date Start Stop Today : : CH Mode Timer Cancel These timer settings overlap. Do you want to save this setting? Wed 10/29 10:00AM - 10:30AM 9:00AM - 10:15AM 25ch 3ch SP SLP If the Timer programming (VCR Plus+) menu appears, press < to switch the display. OK Cancel f Set the following items using </M/m/,. A Press M/m to set the date, then press ,. Each time you press M/m, the item changes as follows. Today y Tomorrow y …… y Tue 10/28 (1 month later) y Sun (every Sunday) y …… y Sat (every Saturday) y Mon-Fri (Monday to Friday) y Mon-Sat (Monday to Saturday) y Sun-Sat (Sunday to Saturday) y Today B Press M/m to set the start time, then press ,. C Press M/m to set the stop time, then press ,. D Press M/m to set the channel, then press ,. When you set the timer for recording from connected equipment, select “Line1,” “Line2,” or “Line3.” E Press M/m to select the recording mode (HQ, HSP, SP, LP, EP, or SLP), then press ,. Timer - Standard OK Set the timer manually. Date Tomorrow Start Stop 8 : 00 PM 8 : 30 PM CH Mode 107 SP Cancel VCR Plus+ ◆ If you make a mistake Press </, to select the item you want to change. ◆ To exit without saving the current setting Press </M/m/, to select “Cancel,” then press ENTER. g Press </M/m/, to select “OK,” then press ENTER. The Timer List menu appears. The TIMER REC indicator lights up on the front panel and the recorder is ready to start recording. To store the setting, press </, to select “OK,” then press ENTER. The programs are recorded in order of priority (page 43). To cancel or change the setting, select “Cancel.” To confirm, change, or cancel timer recording Recording/Timer Recording Mon-Sat VCR Plus+ See “Checking/changing/canceling timer settings (Timer List)” (page 42). z Hints • For recording over the next day, leave the starting date setting as it is, and enter the ending time in the setting. The date will automatically change to the next day. • You can also display the timer programming menu by: – selecting “TIMER” from the System Menu. – selecting “Set Timer” from the TOOLS menu while the Timer List menu is displayed. • You can also use the recorder even when the recorder stands by for recording. To remind you of the timer setting, a message appears on your TV screen five minutes before the timer recording starts. Notes • If “The disc is full or nearly full” appears on the screen, change the disc, or make available space for the recording (DVD-RW/DVD+RW only). • Check that the clock is correctly set before setting the timer recording. If not, the timer recording cannot be made. To record a satellite program, turn on the satellite receiver and select the satellite program you want to record. Leave the satellite receiver turned on until the recorder finishes recording. If you connect equipment with a timer function, you can use the Synchro Rec function (page 47). Rec Mode Adjust If there is not enough available disc space for the recording, the recorder automatically selects the recording mode to enable the program to be recorded. This function is normally set to on. ◆To cancel the function A Press TOOLS while the Timer List is displayed. B Press M/m to select “Rec Mode Adjust,” then press ENTER. C Press </, to select “Off,” then press ENTER. Note This function only works with a timer recording. It does not function with Quick Timer or Synchro Rec. ,continued Timer Recording 41 To extend the recording duration time You can extend the recording duration while recording. 1 2 Press TOOLS during recording. Press M/m to select “Extend Rec. Time,” then press ENTER. The following display appears. Extend Rec. Time OK Set the timer extend function. Cancel Sun 9/28 10:00AM - 11:30AM 3ch SP Checking/changing/canceling timer settings (Timer List) You can check, change, or cancel timer settings using the Timer List menu. a Press SYSTEM MENU. The System Menu appears. Extend Time Off 3 4 Press M/m to select the duration time, then press ENTER. You can set the duration in increments of 10 minutes, up to 60 minutes. Press </M/m/, to select “OK,” then press ENTER. b Press M/m to select “TIMER LIST,” then press ENTER. The Timer List menu appears. TIMER LIST Sports -RW VR Sat 10/25 8:30PM - 9:30PM Mon-Sat 10:00AM - 10:30AM 4ch 25ch HQ SP Wed 10/29 9:00AM - 10:15AM 3ch SLP Thu 10/30 4:00PM - 5:00PM 125ch SLP z Hint You can also extend the recording duration time using “Extend Rec” in the sub-menu of the Timer List. 1 Disc name To enter a disc name, see “Labeling a disc (Disc Name)” (page 72). 2 Timer information: Displays the recording date, time, recording mode, etc. • ❐ indicates the overlapped setting. • a (red) indicates the setting currently being recorded. • z (grey) indicates that the setting cannot be recorded in the selected recording mode. c Press M/m to select the setting you want to check/change/cancel, then press ENTER. The sub-menu appears. d Press M/m to select one of the following items. • Modify • Erase • Check Overlap ◆ To modify the setting A Select “Modify,” then press ENTER. The display for modifying appears. Modify OK Modify the timer setting. Date Mon-Sat Start Stop 10 : 00 PM 10 : 15 PM CH Mode 25 SP Cancel B Press </M/m/, to select the item and change the setting. To undo the change, press </M/m/, to select “Cancel,” then press ENTER or RETURN. To change another setting, repeat step 2. C Press </M/m/, to select “OK,” then press ENTER. 42 Timer Recording ◆ To erase the setting A Select “Erase,” then press ENTER. The display asks for confirmation. The recorder records the programs according to priority if the timer settings overlap. The timer setting set last has priority. If the timer settings overlap, the program that has priority will be recorded. A timer recording of lower priority will be canceled, start from the middle, or stop on the way. Check the overlapped timer settings and change the priority if necessary. Erase Are you sure you want to erase this timer setting? Mon-Sat 10:00AM - 10:30AM 25ch OK Changing the priority of overlapped settings SP Cancel If you do not want to erase the setting, select “Cancel,” then press ENTER or RETURN. If the timer is set using the manual or VCR Plus+ setting, the program set last has priority. Example: you set the timer in order of A, B, and C (setting C has first priority) ◆ To check for overlapped settings 7:00 A Select “Check Overlap,” then press ENTER. The display for confirming overlapped settings appears. The timer setting set most recently is listed at the top and has priority. You may not be able to record the program that has low priority. 9:00 10:30 Wed 10/29 9:00AM - 10:15AM Change priority C Actual recording These timer settings overlap. 10:00AM - 10:30AM 11:00 B Check Overlap Mon-Sat will be cut off A 25ch 3ch A SP 7:00 SLP Close B Recording/Timer Recording B Press </, to select “OK,” then press ENTER. When the timer settings overlap C 9:00 10:30 If you give priority to setting B over setting C, program B will be entirely recorded and program C is recorded only after program B has finished. To change a priority, press </, to select “Change priority.” For details, see “Changing the priority of overlapped settings” below. A 7:00 B C 11:00 9:00 z Hint You can change the priority of a timer setting during recording. B Press </, to select “Close.” To change or cancel the setting, press RETURN to return to the Timer List menu, and repeat steps 3 and d above. e Press RETURN to turn off the Timer List. Note If the end time of one recording and the start time of another are the same, the beginning or end of a program of lower priority may be cut. Example: you made the timer setting A after B 7:00 9:00 10:00 A z Hint While recording, you cannot modify the timer setting for the current recording, but you can extend the recording duration of the recording time (page 42). Note Even if the timer is set for the same program daily or weekly, the timer recording cannot be made if it overlaps with the program that has priority. A mark will appear next to the overlapped setting in the Timer List. Check the priority order of the settings. B a Press SYSTEM MENU. The System Menu appears. b Press M/m to select “TIMER LIST,” then press ENTER. The Timer List menu appears. TIMER LIST Sports -RW VR Sat 10/25 8:30PM - 9:30PM Mon-Sat 10:00AM - 10:30AM 4ch 25ch HQ SP Wed 10/29 9:00AM - 10:15AM 3ch SLP Thu 10/30 4:00PM - 5:00PM 125ch SLP ,continued Timer Recording 43 c Press M/m to select the setting for which you want to change a priority order, then press ENTER. Recording TV programs using the VCR Plus+ system The sub-menu appears. d Press M/m to select “Check Overlap,” then press ENTER. The display for confirming overlapped settings appears. Check Overlap The VCR Plus+ system is a feature that simplifies setting timer recordings. Just enter the PlusCode number listed in the TV program guide. The date, time, and channel of that program are set automatically. Check that the TV and guide channels are correctly set in “Set VCR Plus+ Channels” in “Settings” (page 93). These timer settings overlap. Mon-Sat Wed 10/29 10:00AM - 10:30AM 9:00AM - 10:15AM 25ch 3ch SP SLP Z OPEN/CLOSE Change priority "/1 Number buttons Close e Press </, to select “Change priority,” then press ENTER. CLEAR SET [TIMER] The display for changing priority appears. Change priority 3ch Wed 10/29 9:00AM Cancel Where do you want to move this timer setting? 25ch Mon-Sat 10:00AM RETURN f Press M/m to move the timer setting where you want, then press ENTER. The program moves to its new location in the list. A program higher up in the list has higher priority. To return to the Timer List, select “Cancel.” g Press RETURN to turn off the Timer List. </M/m/,, ENTER x REC STOP a Press }/1. b Turn on the TV, and switch the input selector on your TV so that the signal from the recorder appears on the TV screen. ◆ When using an amplifier (receiver) Turn on the amplifier (receiver) and select the appropriate channel so that you can hear sound from the recorder. c Press Z OPEN/CLOSE, and place a recordable disc on the disc tray. d Press Z OPEN/CLOSE to close the disc tray. Wait until “LOAD” disappears from the front panel display. If you use an unused DVD, formatting starts automatically. When using an unused DVD-RW, select the recording format, VR or Video. 44 Timer Recording e Press [TIMER]. z Hints The Timer programming (VCR Plus+) menu appears. Timer - VCR Plus+ Set the timer by entering the PlusCode. PlusCode Cancel • The Rec Mode Adjust function also works with this timer setting method (page 41). • You can extend the recording duration time during recording (page 42). • You can also display the timer programming menu by: – selecting “TIMER” from the System Menu. – selecting “Set Timer” from the TOOLS menu while the Timer List menu is displayed. Standard Notes If the Timer programming (Standard) menu appears, press < to switch the display. Recording/Timer Recording f Press the number buttons to enter the PlusCode number, then press SET. • Check the clock set before setting the timer recording. If not, the timer recording cannot be made. • You can also use the recorder even when the recorder stands by for recording. To remind you of the timer setting, a message appears on your TV screen five minutes before the timer recording starts. ◆ If you make a mistake Press CLEAR and re-enter the correct number. ◆ To cancel the setting Press </M/m/, to select “Cancel,” then press ENTER. g Press </M/m/, to select “OK,” then press ENTER. The date, start and stop times, channel, and recording mode appears. Timer - VCR Plus+ Is the follwing timer setting correct? To modify, adjust each item or re-enter the PlusCode. Date Start Stop Mon 6/28 10 : 00 AM 11 : 30 AM CH Mode 107 HQ OK Cancel Change ◆ If you want to change the setting A Press </, to select the item you want to change. B Press M/m to change the setting. To cancel the setting, select “Cancel.” To re-enter the PlusCode number, select “Change.” h Press </M/m/, to select “OK,” then press ENTER. The TIMER REC indicator lights up on the front panel, and the recorder is ready to start recording. i Press RETURN to turn off the display. To record from a decoder or other source, leave the connected equipment turned on. To stop recording during timer recording Press x REC STOP. If the timer settings overlap See page 41. To confirm, change, or cancel timer recording See “Checking/changing/canceling timer settings (Timer List)” (page 42). Timer Recording 45 Adjusting the Recording Picture Quality and Size You can adjust the recording picture quality and picture size. ◆ Rec Mode Selects the recording mode for the desired recording time and picture quality. For more information, see “Recording mode” (page 36). • HQ • HSP • SP (default) • LP • EP • SLP ◆ Rec Screen Size Sets the picture size of the program to be recorded • 4:3 (default): Sets the picture size to 4:3. • 16:9: Sets the picture size to 16:9 (wide mode). TOOLS </M/m/,, ENTER RETURN This function works with DVD-Rs and DVD-RWs (Video mode) when the recording mode is set to HQ, HSP, or SP. For all other recording modes, the screen size is fixed at “4:3.” For DVD-RWs (VR mode), the actual picture size is recorded regardless of the setting. For instance, if a 16:9 size picture is received, the disc records the picture as 16:9 even if “Rec Screen Size” is set to “4:3.” For DVD+RWs, the screen size is fixed at “4:3.” ◆ Rec NR (noise reduction) Reduces noise contained in the video signal. a Press TOOLS before recording starts. The TOOLS menu appears. b Press M/m to select “Rec Settings,” then press ◆ Rec Video Equalizer Adjusts the picture in greater detail. Press M/m to select the item you want to adjust, then press ENTER. • Contrast: Changes the contrast. • Brightness: Changes the overall brightness. • Color: Makes the colors deeper or lighter. • Hue: Changes the color balance. ENTER. The following display appears. d Adjust the setting using </M/m/,, then press ENTER. Rec. Settings The larger the number, the greater the effect. The default setting is underlined. Select the item you want to change. Rec Mode : SP Rec Screen Size : 4:3 Rec NR : 1 Rec Video Equalizer Items Settings Rec NR Off 1 ~ 3 Rec Video Equalizer c Press M/m to select the item you want to Contrast –3 ~ 0 ~ 3 adjust, then press ENTER. Brightness –3 ~ 0 ~ 3 The adjustment display appears. Color –3 ~ 0 ~ 3 Hue –3 ~ 0 ~ 3 Example: Rec NR e Repeat steps 3 and 4 to adjust any other Rec NR Off items. 1 2 3 f Press RETURN to turn off the display. Note The adjustments made here are for the recorder and cannot be saved for individual titles. 46 Adjusting the Recording Picture Quality and Size Recording from External Equipment with a Timer (Synchro Rec) You can set the recorder to automatically record programs from connected equipment that has a timer function (such as a satellite receiver). Connect the equipment to the LINE IN 1 jacks of the recorder (page 30). When the connected equipment turns on, the recorder starts recording a programme from the LINE IN 1 jacks. • Check that the disc has enough available space for the recording (page 37). • Adjust the recording picture quality and picture size if necessary (page 46). Z OPEN/CLOSE "/1 Wait until “LOAD” disappears from the front panel display. If you use an unused DVD, formatting starts automatically. When using an unused DVD-RW, select the recording format, VR or Video. e Select the line input audio when recording a program having two types of sound. A Press INPUT SELECT to select “L1.” B Press TOOLS. C Press M/m to select “Line Audio Input,” then press ENTER. D Press M/m to select “Main/Sub*,” then press ENTER. * When recording a program having two types of sound, select “Main/Sub.” Both sounds can be recorded. You can select either sound when playing a disc. Select “Main/Sub” only when using a DVD-RW (VR mode). For other discs, select “Stereo.” Only stereo sound is recorded. f Press REC MODE repeatedly to select the recording mode, HQ, HSP, SP, LP, EP, or SLP. Recording/Timer Recording Before you start… d Press Z OPEN/CLOSE to close the disc tray. g Set the timer on the connected equipment to the time of the program you want to record, and turn it off. TOOLS </M/m/,, ENTER x REC STOP REC MODE SYNCHRO REC h Press SYNCHRO REC. The SYNCHRO REC indicator lights up on the front panel. The recorder automatically turns off and stands by for Synchro-Recording. The recorder automatically starts recording when it receives an input signal from the connected equipment. The recorder stops recording when the connected equipment turns off. INPUT SELECT To stop recording a Press }/1. b Turn on the TV, and switch the input selector on your TV so that the signal from the recorder appears on the TV screen. ◆ When using an amplifier (receiver) Turn on the amplifier (receiver) and select the appropriate channel so that you can hear the sound from the recorder. c Press Z OPEN/CLOSE, and place a Press x REC STOP. To cancel Synchro Rec Press SYNCHRO REC or turn on the recorder before the Synchro-Recording Starts. The SYNCHRO REC indicator turns off. If the timer settings of a Synchro-Recording and another timer recording overlap Regardless of whether or not the program is a Synchro Rec program, the program that starts first has priority and the second program starts recording only after the first program has finished. recordable disc on the disc tray. 7:00 8:00 9:00 10:00 First program Second program will be cut off ,continued Recording from External Equipment with a Timer (Synchro Rec) 47 Notes • The recorder starts recording only after detecting the video signal from the connected equipment. The beginning of the program may not be recorded. • You cannot set Synchro-Recording only by pressing the SYNCHRO REC button when the recorder is turned off. Be sure to turn on the recorder first to set Synchro-Recording. • While Synchro-Recording, other operations such as normal recording cannot be done. • Do not turn on the recorder while it stands by for Synchro-Recording. Synchro-Recording will be canceled. • Any program that contains a Copy-Never copy guard signal cannot be recorded. When you record a program that contains a Copy-Once signal, use a DVD-RW (Ver. 1.1 with CPRM) in VR mode for recording. For details, see “Unrecordable pictures” (page 36). • When using the Synchro Rec function, do not use the VCR control function on connected equipment. • To use the connected equipment while the recorder is standing by for Synchro-Recording, cancel Synchro-Recording by pressing SYNCHRO REC. Before timer recording starts, be sure to turn off the connected equipment, then turn on the recorder and press SYNCHRO REC to reset Synchro-Recording. • The Synchro Rec function does not work with some satellite receivers. For details, refer to the satellite receiver’s operating instructions. 48 Recording from External Equipment with a Timer (Synchro Rec) Before Playing Playback Read the following information before playing a disc. This section explains the basics of playback, such as playable disc types, and describes the settings necessary for playback in general. Playable discs This recorder can play the following discs in both the 12 cm and 8 cm sizes. ◆Disc types DVD VIDEO* Playback DVD-RW* Ver. 1.0 Ver. 1.1 Ver. 1.1 with CPRM DVD+RW* DVD-R* DVD+R* Music CD • Before Playing . . . . . . . . . . . . . . . . . . .page 49 • Playing Discs CD-R/CD-RW (Music CD format only) . . . . . . . . . . . . . . . .page 50 • Selecting a Recorded Title on a Disc . . . . . . . . .page 53 • Searching for a Title/Chapter/Track . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 55 * “DVD VIDEO,” “DVD-RW,” “DVD+R,” “DVD+RW,” and “DVDR” are trademarks. Region code (DVD VIDEO only) Your recorder has a region code printed on the rear of the unit and will only play DVD VIDEOs (playback only) labeled with identical region codes. This system is used to protect copyrights. • Checking the Play Information and Playing Time DVD VIDEOs labeled . . . . . . . . . . . . . . . . . . . . . .page 56 • Selecting the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 57 • TV Virtual Surround Settings (TVS) . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 58 will also play on this recorder. ALL If you try to play any other DVD VIDEO, the message “Playback prohibited by region code.” will appear on the TV screen. Depending on the DVD VIDEO, no region code indication may be labeled even though playing the DVD VIDEO is prohibited by area restrictions. X • Changing the Angles . . . . . . . .page 59 Region code RDR–XXXX 00V 00Hz 00W • Displaying the Subtitles . . . . . .page 60 NO. 0-000-000-00 • Adjusting the Playback Picture and Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 60 ,continued Before Playing 49 Discs that cannot be played on this recorder The recorder cannot play the following discs: • All CD-ROMs (including PHOTO CDs) • CD-Rs/CD-RWs, other than those recorded in the music CD format • Data part of CD-Extras • VIDEO CDs • Super VCDs • DVD-ROMs • DVD Audio discs • DVD-RAMs • HD layer on Super Audio CDs • DVD VIDEOs with a different region code (page 49) • A disc recorded in a color system other than NTSC, such as PAL or SECAM Notes on playing DTS sound tracks on a CD • When playing DTS-encoded CDs, excessive noise will be heard from the analog stereo jacks. To avoid possible damage to the audio system, the consumer should take proper precautions when the analog stereo jacks of the recorder are connected to an amplification system. To enjoy DTS Digital Surround™ playback, an external 5.1-channel decoder system must be connected to the digital jack of the recorder. • Set the sound to “Stereo” using the AUDIO button when you play DTS sound tracks on a CD (page 57). • Do not play DTS sound tracks without first connecting the recorder to an audio component having a built-in DTS decoder. The recorder outputs the DTS signal via the DIGITAL OUT (COAXIAL or OPTICAL) jack even if “DTS” is set to “Off” in the Audio Setup (page 96), and may affect your ears or cause your speakers to be damaged. Playing Discs Depending on the disc, some operations may differ, or certain restrictions may apply. Refer to the operating instructions supplied with your disc. Z OPEN/CLOSE "/1 Number buttons, SET TOP MENU MENU </M/m/,, ENTER H PLAY x STOP Notes on playing DVDs with a DTS sound track • DTS audio signals are output only through the DIGITAL OUT (COAXIAL or OPTICAL) jack. • When you play a DVD with DTS sound tracks, set “DTS” to “On” in the Audio Setup (page 96). • If you connect the recorder to audio equipment without a builtin DTS decoder, do not set “DTS” to “On” in the Audio Setup (page 96). A loud noise may come out from the speakers, affecting your ears or causing the speakers to be damaged. Notes • The following type of high-speed discs can be played back on this recorder: up to 2×-speed DVD-RWs (Revision 1.0), up to 4×-speed DVD-Rs (Revision 1.0), or up to 4×-speed DVD+RWs/DVD+Rs. • DVD-RW/-Rs, DVD+RWs/+Rs, or CD-RW/-Rs recorded on another recording device cannot be played on this recorder if they have not been correctly finalized. Some discs cannot be played due to the recording quality or physical condition of the disc, or the characteristics of the recording device and authoring software. a Press }/1. The recorder turns on and the power indicator lights up in green. b Turn on the TV, and switch the input selector on your TV so that the signal from the recorder appears on the TV screen. ◆ When using an amplifier Turn on the amplifier (receiver) and select the appropriate channel so that you can hear sound from the recorder. c Press Z OPEN/CLOSE to open the disc tray. d Place a disc on the disc tray. With the playing side facing down e Press Z OPEN/CLOSE to close the disc tray. Wait until “LOAD” disappears in the front panel display. 50 Playing Discs ◆ When playing a DVD-RW/DVD+RW/DVD-R You can select the title from the Title List menu. See “Selecting a Recorded Title on a Disc” (page 53). ◆ If a menu appears on the TV screen See “Using the DVD’s Menu” below. c Press ENTER. z Hint If you are playing a finalized DVD-R, DVD+RW, or DVD-RW (Video mode), you can display the menu with the TOP MENU or MENU button. See “Finalizing a disc (Finalize)” (page 73) for more information about finalizing and DVD menus. f Press H PLAY. The recorder starts playback. Using the PROGRESSIVE button To adjust the volume Adjust the volume of your TV or amplifier (receiver). To stop playback Press x STOP. Press @/1. PROGRESSIVE (the PROGRESSIVE indicator lights up) z Hint You can also start or stop playback using the TOOLS menu. To play a DVD VIDEO for which Parental Control is set When the message “Do you want temporarily change parental control to *?” appears on the TV screen, follow the steps below. Press </, to select “OK,” then press ENTER. The display for entering your password appears. Parental Control Enter your password. Cancel Password 2 Enter your four digit password using the number buttons. The cursor moves to “OK.” 3 Press ENTER to select “OK.” The recorder starts playback. • INTERLACE Select this when you are connected to a standard (Interlace format) TV. • PROGRESSIVE Select this when you are connected to a TV compatible with progressive signals. The recorder outputs video signals in progressive format. Playback INTERLACE (the PROGRESSIVE indicator turns off) To turn off the recorder 1 You can fine-tune the Progressive 480p video signal output when you press PROGRESSIVE on the front panel (the PROGRESSIVE indicator lights up) and connect the recorder using the COMPONENT VIDEO OUT jacks to a TV that is able to accept the video signal in progressive format. Press PROGRESSIVE repeatedly to toggle the displays as follows: ◆ Conversion modes DVD software can be divided into two types: film based software and video based software. Video based software is derived from the TV, such as dramas and sit-coms, and displays images at 30 frames/60 fields per second. Film based software is derived from film and displays images at 24 frames per second. Some DVD software contains both Video and Film. In order for these images to appear natural on your screen when output in PROGRESSIVE mode (60 frames per second), the progressive video signal needs to be converted to match the type of DVD software that you are watching. The title recorded on this recorder is Video based software. If you want to set the conversion mode for Video based software regardless of the software type, set “Progressive Mode” in Video Setup to “Video” (page 95). Notes To register or change the password, see “Parental Control (DVD VIDEO only)” (page 97). Using the DVD’s Menu When you play a DVD VIDEO which contains several titles, you can select the title you want using the TOP MENU or MENU button. When you play DVD VIDEOs that allow you to select items such as the language for the subtitles and the language for the sound, select these items using the MENU button. • When you play video based software with progressive signals, sections of some types of images may appear unnatural due to the conversion process when output through the COMPONENT VIDEO OUT jacks. Images from the LINE OUT (S VIDEO) 1/2 and LINE OUT (VIDEO) 1/2 jacks are unaffected as they are output in the normal (interlace) format. • If you have set the recorder to progressive format even though your TV is not compatible with progressive format (480p) signals, you cannot view pictures. Some video signals recorded on the disc may not be converted in progressive format. In either of these cases, set the recorder to interlace format. a Press TOP MENU or MENU. The disc’s menu appears on the TV screen. The contents of the menu vary from disc to disc. b Press </M/m/, or the number buttons to select the item you want to play or change. ,continued Playing Discs 51 Basic operations/Changing the playback speed Z OPEN/CLOSE INSTANT REPLAY INSTANT SEARCH TOOLS m / M (Search) </M/m/,, ENTER ./> PREV/NEXT x STOP X PAUSE Jog Stick H PLAY To: Operations Discs Pause Press X PAUSE. To resume playback, press X PAUSE or H PLAY. All discs Locate the beginning of the title/chapter/track During playback, press > NEXT or . PREV. • > NEXT : Goes to the next title/chapter/track. • . PREV : Goes back to the beginning of the previous title/chapter/ track. For DVD-RWs (VR mode), you can manually add chapter marks (page 67). All discs Stop play and remove the disc Press Z OPEN/CLOSE. All discs Replay the previous scene INSTANT REPLAY. Press This function is useful when you want to review a scene or dialogue you missed. Briefly fast forward the current scene Press INSTANT SEARCH. This function is useful for skipping a scene you do not want to watch. Fast forward/fast reverse (search) During playback, briefly push the Jog Stick to the left or right. Each time you push the Jog Stick, the search speed changes as follows: fast reverse m FR1 T FR2 T T FR3* T T T fast forward M t FF1 t t FF2 t t t FF3* To resume to the normal speed, press H PLAY. When you push and hold the Jog Stick down to the left or right, fast forward/fast reverse continues at the selected speed until you release the Jog Stick. Actual speeds may differ with some discs or recording modes. * Music CDs cannot be played at FR3/FF3. 52 Frame by frame (Slowmotion play) Push m / M Jog Stick for more than one second when the recorder is in pause mode. To return to the normal speed, press H PLAY. Watch one frame at a time (Freeze Frame) Push m / M Jog Stick briefly when the recorder is in pause mode. To return to the normal speed, press H PLAY. Playing Discs All discs To resume playback from the point where you stopped the disc (Resume Play) When you stop the disc, the recorder remembers the point where you pressed x STOP. • For DVDs: Resume Play works as long as you do not open the disc tray (you may turn off the recorder). • For CDs: Resume Play works as long as you do not turn off the recorder or open the disc tray. While playing a disc, press x STOP to stop playback. “RESUME” appears on the front panel display. If “RESUME” does not appear, Resume Play is not available. 2 Press H PLAY. The recorder starts playback from the point where you stopped the disc in step 1. The Title List menu displays all the titles recorded on the disc and you can select the one you want to play. For details, see also page 32. Playback 1 Selecting a Recorded Title on a Disc ◆To play from the beginning of the disc Reset the resume point using the TOOLS menu. Press TOOLS and press M/m to select “Reset Resume,” then press ENTER. ◆To play from the beginning of the title You can locate the beginning of the title/track using the TOOLS menu. Press TOOLS and press M/m to select “Play From Start,” then press ENTER. Playback automatically starts from the beginning of the title. TITLE LIST SYSTEM MENU </M/m/,, ENTER ZOOM +/– CURSOR MODE RETURN m/M H PLAY X PAUSE Notes • Depending on the disc, the recorder may not resume playback from where you stopped the disc. • Depending on where you stopped the disc, the recorder may not resume playback from exactly the same point. • The point where you stopped playing is cleared when: – you open the disc tray. – you play another title. – you switch the Title List menu (Original or Playlist). – you edit the disc, such as erasing a title. – you change the settings on the recorder. – you turn off the recorder (CD only). – you make a recording (except for DVD-RWs in VR mode). a Insert a disc and press TITLE LIST. The Title List menu appears. For a DVD-RW (VR mode), select “Original” or “Playlist” using the TOOLS menu (page 32). -RW.VR TITLE LIST ORIGINAL My Movies 1.5/4.7GB 1 2ch 1:00PM - 2:00PM 9/15 Date 2 5ch 8:00PM - 9:00PM 9/17 Number 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 5 25ch 8:00PM - 8:30PM 10/15 6 L2 9:00PM - 9:30PM 10/19 7 8ch 9:00PM - 9:30PM 10/26 8 125ch 10:00AM - 10:30AM 10/28 Sort Title b Press M/m to select the title, then press ENTER. The sub-menu appears. c Press M/m to select “Play,” then press ENTER. Playback starts from the selected title on the disc. z Hints • You can also display the Title List menu using the System Menu. Press SYSTEM MENU and select “TITLE LIST,” then press ENTER (page 32). • You can select Page mode by pressing CURSOR MODE (page 32). In Page mode, you can change the page of the Title List using M/m. • You can also use the H PLAY button to start playback. • To change the title name, see “Labeling a title (Title Name)” (page 64). ,continued Selecting a Recorded Title on a Disc 53 To change the title order (Sort) You can sort the titles according to date, number, or title. 1 Press < while the Title List menu is turned on. The Sort buttons are selected. -RW.VR TITLE LIST Sort buttons 1.5/4.7GB 2ch 1:00PM - 2:00PM 9/15 Date 2 5ch 8:00PM - 9:00PM 9/17 Number 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 5 25ch 8:00PM - 8:30PM 10/15 6 L2 9:00PM - 9:30PM 10/19 7 8ch 9:00PM - 9:30PM 10/26 8 125ch 10:00AM - 10:30AM 10/28 Title 2 My Movies ORIGINAL 1 Sort To change a title thumbnail picture (Thumbnail) (DVD-RW in VR mode only) You can select a favourite scene for a thumbnail picture in a zoomed Title List menu. 1 Press TITLE LIST while a disc is in the recorder. The Title List menu appears. 2 Press M/m to select a title whose thumbnail picture you want to change, then press ENTER. The sub-menu appears. 3 Press M/m to select “Set Thumbnail,” then press ENTER. The display for setting a thumbnail picture appears. The selected title starts to play in the background. Press M/m to select date, number, or title, then press ENTER. The titles are sorted in selected order. Order Sorted Date in order of date (when the titles were recorded). The title that is recorded most recently is listed at the top. Number in order of recorded title number. Title in alphabetical order. Set Thumbnail 1 2ch 1:00PM - 2:00PM 0:00:45 4 To show the list in greater detail (Zoom) Press ZOOM+ while the Title List menu is turned on to view detailed information about the title. To return to the normal Title List menu, press ZOOM–. Example: DVD-RW (VR mode) While watching the playback picture, press H PLAY, X PAUSE, or m/M to select the scene you want to set for a thumbnail picture, then press ENTER. Playback pauses at the selected scene, and the display asks for confirmation. Set Thumbnail Do you want to set this point as a Thumbnail? -RW.VR Sort Date Number Title TITLE LIST ORIGINAL My Movies 1.5/4.7GB OK 1 2ch 1:00PM - 2:00PM 2ch Mon 9/15 1:00PM( 1H00M) SP 5ch 8:00PM - 9:00PM 5ch Wed 9/17 8:00PM( 1H00M) SLP Change Cancel 2 3 12ch 9:00AM - 9:30AM 12ch EP Thu 9/25 9:00AM( 0H30M) 4 3ch 8:00PM - 8:30PM 3ch Thu 9/25 8:00PM( 0H30M) SLP To change the selection, select “Change.” 5 Press </, to select “OK,” then press ENTER. The scene is set for the title’s thumbnail picture. 6 Press RETURN to turn off the display. 1 Title’s thumbnail picture 2 Title information: Displays the title number, title name, date/time of recording, channel, and recording mode*. • indicates that the title is protected. • a (red) indicates that the title is being recorded. * The displayed recording mode refers to the mode selected when the program was recorded on this recorder. 54 Selecting a Recorded Title on a Disc z Hint After recording, the first scene of the recording (the title) is automatically set for the thumbnail picture. Notes • Title thumbnail pictures are displayed only on this recorder. • It may take a few seconds for the thumbnail pictures to be displayed. Searching for a Title/ Chapter/Track c Press the number buttons to select the number of the title, chapter, track, time code, etc., you want. For example: Time Search To find a scene at 2 hours, 10 minutes, and 20 seconds, enter “21020.” ◆ If you make a mistake Press CLEAR to cancel the number, then select another number. You can search a DVD by title or chapter, and a CD by track. Since titles and tracks are assigned unique numbers on the disc, you can select the desired title/chapter/track by entering its number. Or, you can search for a scene using the time code. d Press SET. The recorder starts playback from the selected title/ chapter/track/scene. To cancel searching Number buttons, SET Playback Press RETURN. Notes CLEAR • You cannot search for a still picture on a DVD-RW (VR mode) using Time Search. • If you enter a number that does not exist, the current selection does not change. TOOLS M/m, ENTER RETURN a Press TOOLS during playback. The TOOLS menu appears. b Press M/m to select the search method, then press ENTER. • Title Search (for DVDs) • Chapter Search (for DVDs) • Track Search (for CDs) • Time Search (for DVDs): Searches for a starting point by entering the time code. The display for entering the number appears. Example: Title Search Title : -- (21) The number in parentheses indicates the total number of titles, tracks, etc. Searching for a Title/Chapter/Track 55 Checking the Play Information and Playing Time ◆ Display 2 Example: When playing a DVD-RW (VR mode) Original DVD-RW VR SP T1 0:00:45 1 Disc type/format (page 35) You can check the playing time and remaining time of the current title, chapter, or track. Also, you can check the disc name recorded on the disc. 2 Title type (Original or Playlist) (page 32) 3 Play mode 4 Recording mode* (page 36) 5 Playing status bar 6 Title number (page 53) 7 Playing time * The displayed recording mode refers to the mode selected when the program was recorded on this recorder. To check the remaining time TIME/TEXT DISPLAY Press DISPLAY repeatedly. Each time you press the button, the display changes as follows: Title/track information (Display 1) m Play mode/time information (Display 2) m (Display off) The displays differ depending on the disc type or playing status. ◆ Display 1 Example: When playing a DVD VIDEO Press TIME/TEXT repeatedly while the Display 2 is displayed above. Each time you press the button, the display changes in the following order. ◆When playing a DVD • Playing time of the current title (hours: minutes: seconds) • Remaining time of the current title • Playing time of the current chapter • Remaining time of the current chapter • Disc name (DVD-RW/DVD+RW/DVD-R only) ◆When playing a CD • Playing time of the current track (minutes: seconds) • Remaining time of the current track • Playing time of the current disc • Remaining time of the current disc • Disc name To check the disc name (except DVD VIDEO) Press TIME/TEXT repeatedly while the Display 2 is displayed. The text appears only when text is recorded on a CD, or if you input the disc’s name. To label a DVD-RW/DVD+RW/DVD-R, see “Labeling a disc (Disc Name)” (page 72). Title 1 Movies 1 : English DolbyDigital 2/0 1 Title/track number/name 2 Available disc functions (angle/audio/subtitle, etc.) 3 The current selected function or audio setting (appears only temporarily) 56 Checking the Play Information and Playing Time DVD-RW VR SP T2 0:00:45 Text, Disc name z Hint When “Auto Display” is set to “On” (default) in Options Setup (page 99), playback information automatically appears for several seconds after starting playback. Checking the playing time on the front panel display Selecting the Sound You can view the playing or time information and text displayed on the TV screen also on the front panel display. Press TIME/TEXT repeatedly. Each press of the button changes the information as follows: ◆When playing a DVD Title playing time and the current title/chapter number Remaining time of the current title Playing time and number of the current chapter Playback When playing a DVD VIDEO recorded in multiple audio formats (PCM, Dolby Digital, or DTS), you can select the audio format. If a DVD VIDEO is recorded with multilingual tracks, you can also change the language. With CDs, you can select the sound from the right or left channel and listen to the sound of the selected channel through both the right and left speakers. For example, when playing a disc containing a song with the vocals on the right channel and the instruments on the left channel, you can listen to the instruments only from both speakers, by selecting the left channel. Remaining time of the current chapter AUDIO Disc name DISPLAY ◆When playing a CD Track playing time and the current track/index number Press AUDIO repeatedly during playback to select one of the audio options. Remaining time of the current track The following display appears. Example: DVD VIDEO Playing time of the disc Remaining time of the disc Disc name z Hint Long text that does not fit in a single line will scroll across the front panel display. Notes • Depending on the type of disc being played, the disc’s text may not be displayed. • The recorder can only display the first level of a CD’s text, such as the disc name. • The letters or symbols that cannot be displayed are replaced with “*.” 1 : English DolbyDigital 2/0 ◆When playing a DVD VIDEO Depending on the DVD VIDEO, the choice of language varies. When four numbers are displayed, they indicate a language code. To see which language the code represents, see “Language Code List” (page 108). When the same language is displayed two or more times, the DVD VIDEO is recorded in multiple audio formats. ◆When playing a DVD-RW in VR mode The types of sound tracks recorded on a disc are displayed. The default setting is underlined. For a disc recorded on this recorder, the sound can be selected only if recorded from equipment connected to the LINE IN jacks. Example: • 1: Main (main sound) • 1: Sub (sub sound) • 1: Main/Sub (main and sub sound) ,continued Selecting the Sound 57 ◆When playing a CD The default setting is underlined. • Stereo: The standard stereo sound • 1/L: The sound of the left channel (monaural) • 2/R: The sound of the right channel (monaural) TV Virtual Surround Settings (TVS) Notes • Depending on the disc, you may not be able to change the audio format. • When playing a DVD-RW in VR mode: If you connected to an AV amplifier (receiver) using the DIGITAL OUT (COAXIAL or OPTICAL) jack and want to switch between the sound tracks, set “Dolby Digital” in Audio Setup to “D-PCM.” Checking the audio signal format When playing a DVD, you can check the format of the current audio signal (Dolby Digital, DTS, PCM, etc.). Press DISPLAY. When you connect a stereo TV or two front speakers, TVS (TV Virtual Surround) lets you enjoy surround sound effects by using sound imaging to create virtual rear speakers from the sound of the front speakers (L: left, R: right) without using actual rear speakers. If the recorder is set up to output the signal from the DIGITAL OUT (OPTICAL or COAXIAL) jack, the surround effect will only be heard when “Dolby Digital” in Audio Setup is set to “DPCM” (page 96). TVS was developed by Sony to produce surround sound for home use using just a stereo TV. The following display appears. Example: Dolby Digital 5.1 ch Rear (L/R) SUR 1 : English DolbyDigital 3/2.1 Front (L/R) + Center LFE (Low Frequency Effect) ◆About audio signals Audio signals recorded in a disc contain the sound elements (channels) shown below. Each channel is output from a separate speaker. • Front (L) • Front (R) • Center • Rear (L) • Rear (R) • Rear (Monaural): This signal can be either Dolby Surround Sound processed signals or Dolby Digital sound’s monaural rear audio signals. • LFE (Low Frequency Effect) signal Note If “DTS” is set to “Off” in Audio Setup, the DTS track selection option will not appear on the screen even if the disc contains DTS tracks (page 96). Press SUR repeatedly during playback to select one of the TVS sounds. Refer to the following explanations given for each item. • Off • Dynamic • Wide • Night • Standard TV Virtual Surround modes ◆Dynamic Creates one set of virtual rear speakers from the sound of the actual front speakers (L, R) as shown below. This mode is effective when the distance between the front L and R speakers is short, such as with built-in speakers on a stereo TV. TV ◆Wide Creates five sets of virtual rear speakers from the sound of the actual front speakers (L, R) as shown below. This mode is effective when the distance between the front L and R speakers is short, such as with built-in speakers on a stereo TV. TV 58 TV Virtual Surround Settings (TVS) ◆Night Large sounds, such as explosions, are suppressed, but quieter sounds are unaffected. This feature is useful when you want to hear the dialogue and enjoy the surround sound effects of “Wide” at low volume. Changing the Angles ◆Standard Creates three sets of virtual rear speakers from the sound of the actual front speakers (L, R) as shown below. This mode is effective when you use two separate front speakers. L R If various angles (multi-angles) for a scene are recorded on a DVD VIDEO, “ANGLE” appears in the front panel display, indicating that you can change the viewing angle. ANGLE Playback L: Front speaker (left) R: Front speaker (right) : Virtual speaker To cancel the setting Select “Off”. z Hint You can select the TVS mode from the TOOLS menu (page 61). Notes • When the playing signal does not contain a signal for the rear speakers, the surround effects will be difficult to hear. • When you select one of the surround modes, turn off the surround setting of the connected TV or amplifier (receiver). • Make sure that your listening position is between and at an equal distance from your speakers, and that the speakers are located in similar surroundings. • Not all discs will respond to the “Night” function in the same way. • The TVS function cannot be used with discs recorded on this recorder. Press ANGLE repeatedly during playback to select an angle. The scene changes to the selected angle. Angle 1(3) Notes • Depending on the DVD VIDEO, you may not be able to change the angles even if multi-angles are recorded on the disc. • You cannot change the angles when playing a disc recorded on this recorder. Changing the Angles 59 Displaying the Subtitles Adjusting the Playback Picture and Sound You can adjust the video/audio signal from the recorder to obtain the picture or sound quality you want. If subtitles are recorded on a disc you can change the subtitle language or turn the subtitles on and off whenever you want during playback. SUBTITLE TOOLS </M/m/,, ENTER RETURN Press SUBTITLE repeatedly during playback to select a setting. 1 : English Depending on the DVD VIDEO, the choice of language varies. When four numbers are displayed, they indicate a language code. To see which language the code represents, see “Language Code List” (page 108). To turn off the subtitles Select “Off”. Notes Adjusting the picture quality a Press TOOLS during playback. The TOOLS menu appears. b Press M/m to select “Video Settings,” then press ENTER. The following display appears. Video Settings Select the item you want to change. • Depending on the DVD VIDEO, you may not be able to change the subtitle language even if multilingual subtitles are recorded on it. You also may not be able to turn them off. • You cannot change the subtitles when playing a disc recorded on this recorder. Y NR : 2 C NR : 2 BNR : 2 DVE : Off PB Video Equalizer c Press M/m to select the item you want to adjust, then press ENTER. The adjustment display appears. Example: Y NR Y NR Off 1 2 3 ◆ Y NR (luminance noise reduction) Reduces noise contained in the luminance element of the video signal. 60 Displaying the Subtitles ◆ C NR (chroma noise reduction) Reduces noise contained in the color element of the video signal. ◆ BNR (block noise reduction) Reduces “block noise” or mosaic like patterns in the picture. ◆ DVE (digital video enhancer) Sharpens the outlines of the images. Adjusting the sound quality a Press TOOLS. The TOOLS menu appears. ◆ PB Video Equalizer (Playback video equalizer) Adjusts the picture in greater detail. Press M/m to select the item you want to adjust, then press ENTER. • Contrast: changes the contrast. • Brightness: changes the overall brightness. • Color: makes the colors deeper or lighter. • Hue: changes the color balance. The larger the number, the greater the effect. The default settings are underlined. The following display appears. Audio Settings Select the item you want to change. Surround : Off Audio Filter : Sharp c Press M/m to select the item, then press ENTER. Playback d Press </, to adjust the setting, then press ENTER. b Press M/m to select “Audio Settings,” then press ENTER. Example: Surround (TVS) Surround (TVS) Items Settings Y NR Off 1 2 3 C NR Off 1 2 3 BNR Off 1 2 3 Select a surround effect. Off Dynamic Wide Night DVE Off 1 2 3 Standard PB Video Equalizer Contrast –3 ~ 0 ~ 3 Brightness –3 ~ 0 ~ 3 Color –3 ~ 0 ~ 3 Hue –3 ~ 0 ~ 3 e Repeat steps 3 and 4 to adjust any other items. f Press RETURN to turn off the display. Notes • If the outlines of the images on your screen become blurred, set “BNR” to “Off.” • Depending on the disc or the scene being played, the BNR effect may be hard to discern. The BNR function may not work with some screen sizes. • When playing a disc recorded in SLP recording mode, the BNR setting may have little effect. ◆ Surround (DVD VIDEO only) Selects one of the surround modes. For more information, see “TV Virtual Surround Settings (TVS)” (page 58). • Off (default) • Dynamic • Wide • Night • Standard ◆ Audio Filter (all discs) Selects the digital filter to reduce noise above 22.05 kHz (Fs* is 44.1 kHz), 24 kHz (Fs is 48 kHz), or 48 kHz (Fs is above 96 kHz). • Sharp (default): Provides a wide frequency range and spatial feeling. • Slow: Provides smooth and warm sound. * Sampling frequency of audio source This function affects output signals from the LINE OUT (AUDIO L/R) 1/2 jacks. d Press </M/m/, to select the option, then press ENTER. e Press RETURN to turn off the display. Note There may be little effect by changing the Audio Filter depending on the disc or playback environment. Adjusting the Playback Picture and Sound 61 Before Editing Editing a DVD This section introduces the basics of DVD editing, and explains both edit functions for the recording on a disc and the edit functions for the entire disc. This recorder offers various edit options. Before you edit, read the following to see what is available for your disc. Note that you may lose the edited contents if you remove the disc or a timer recording starts while editing. Checking the disc type, recording format, and title type Press TITLE LIST, and check the disc type and recording format indicated at the top of the Title List menu. If the disc is a VR mode disc, check also the title type, Original or Playlist. If you edit an original title instead of a Playlist title by mistake, it is irreversible. You will be unable to recover the erased title, or revert the edited title to the previous status. Edit options for DVD-RWs (Video mode)/DVD+RWs/DVD-Rs You can perform simple edits. Since Video mode titles are actual recordings on the disc, you cannot undo the edits you have done. Title List menu for DVD-RWs (Video mode)/DVD+RWs/DVD-Rs Disc type/ Recording format -RW.VIDEO TITLE LIST My Movies 1.5/4.7GB 1 2ch 1:00PM - 2:00PM 9/15 Date 2 5ch 8:00PM - 9:00PM 9/17 Number 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 5 25ch 8:00PM - 8:30PM 10/15 6 L2 9:00PM - 9:30PM 10/19 7 8ch 9:00PM - 9:30PM 10/26 8 125ch 10:00AM - 10:30AM 10/28 Sort Title Basic edit functions available with Video mode titles: – Setting protection against erasure (page 64). – Labeling a title (page 64). – Erasing a title (page 65). – Erasing multiple titles (page 65). Notes • Once the disc is finalized, you cannot edit or record on the disc (except for DVD-RWs in VR mode and DVD+RWs). • You cannot create a Playlist (see below) on a DVD-RWs (Video mode), DVD+RW, or DVD-Rs. • Before Editing . . . . . . . . . . . . . . . . . . . page 62 • Basic Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 64 • Advanced Editing (Playlist Edit) . . . . . . . . . . . . . . . . . . . . . . page 67 • Labeling, Protecting, or Finalizing the Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 72 62 Before Editing Edit options for DVD-RWs (VR mode) You have two options for a DVD-RW (VR mode): editing either the original recording (called the “Original”), or the playback information created from the Original (called a “Playlist”). Since each is different in nature and offers different merits, read the following and select the one that better suits your needs. Advanced edit functions available with the Playlist: – Labeling a title (page 64). – Erasing a title (page 65). – Erasing multiple titles (page 65). – Erasing a section of a title (A-B Erase) (page 66). – Creating a Playlist title from selected titles and scenes (page 67). – Rearranging the title order (page 70). – Dividing a title into multiple titles (page 70). – Combining multiple titles into one title (page 71). Editing the “Original” Basic edit functions available with Originals: – Labeling a title (page 64). – Setting protection against erasure (page 64). – Erasing a title (page 65). – Erasing multiple titles (page 65). – Erasing a section of a title (A-B Erase) (page 66). All edits made to the original title are final. If you plan to retain an unaltered original recording, create and edit a Playlist (see below). Editing a DVD The Title List (Original) menu displays all the original titles on the disc. Disc type/ Recording format -RW.VR Title type TITLE LIST My Movies ORIGINAL 1.5/4.7GB 1 2ch 1:00PM - 2:00PM 9/15 Date 2 5ch 8:00PM - 9:00PM 9/17 Number 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 5 25ch 8:00PM - 8:30PM 10/15 6 L2 9:00PM - 9:30PM 10/19 7 8ch 9:00PM - 9:30PM 10/26 8 125ch 10:00AM - 10:30AM 10/28 Sort Title Note Original titles provide a source for the created Playlist. If you use an original title for a Playlist, you will be unable to erase the original title. Editing the “Playlist” A Playlist is a group of Playlist titles created from the original title for editing purposes. When you create a Playlist, only the control information necessary for playback, such as the playback order, is stored on the disc. Example: You have recorded the final few matches of a football tournament on a DVD-RW (VR mode). You want to create a digest with the goal scenes and other highlights, but you also want to keep the original recording. In this case, you can collect the scenes of the highlights, and create playback information (a Playlist title). You can even rearrange the scene order within the Playlist title. The above is only an example. Try using the Playlist’s various edit functions, or use them in conjunction with an Original edit. Devise your own ways of editing with Playlists and Originals. The Title List (Playlist) menu displays the Playlist titles on the disc. Disc type/ Title type Recording format -RW.VR Sort Date TITLE LIST PLAYLIST My Movies 1.5/4.7GB 1 2ch 1:00PM - 2:00PM 9/15 2 5ch 8:00PM - 9:00PM 9/17 Number Title Before Editing 63 b Press M/m to select the title, then press ENTER. Basic Editing The sub-menu appears. c Press M/m to select “Title Name,” then press ENTER. This section explains the basic edit functions. Note that these edits are irreversible to the original status. If you want to edit a DVD-RW (VR mode) without changing the original recordings, create a Playlist (page 67). The display for entering a title name appears. To enter character, see page 34. Input Title Name 2ch 1:00PM - 2:00PM Notes "A" • If “No new data can be added to this disc” appears on the screen, erase any unwanted titles before editing. • For DVD-Rs/DVD-RWs (Video mode): Finish all the editing before finalizing the disc. You cannot edit a finalized disc. • For original titles in DVD-RWs (VR mode): Original titles provide a source for derived Playlist. When you use an original title for a Playlist, you will be unable to erase or edit the original title. - 1 2 A B C . 2 3 D E 3 1 , F 4 G H I 4 5 J L 5 K 6 M N O 6 Back 7 P Q R S Clear All 8 T U V 8 9 W X Y Z Space 0 "a" 7 Symbol 9 Cancel 0 Finish d When you finish entering the title name, press </M/m/, to select “Finish.” A new Title List menu appears with the title of the entered name. TITLE LIST TOOLS </M/m/,, ENTER ./> PREV/NEXT m/M H PLAY X PAUSE CHAPTER MARK CHAPTER ERASE Protecting a title (Protect Title) You can set protection for a title so that the title cannot be erased. a Press TITLE LIST. The Title List menu appears. If you are using a DVDRW (VR mode), press TOOLS and select “Original” from the TOOLS menu. -RW.VR TITLE LIST 1:00PM - 2:00PM 9/15 Date 2 5ch 8:00PM - 9:00PM 9/17 Number 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 5 25ch 8:00PM - 8:30PM 10/15 6 L2 9:00PM - 9:30PM 10/19 7 8ch 9:00PM - 9:30PM 10/26 8 125ch 10:00AM - 10:30AM 10/28 Labeling a title (Title Name) a Press TITLE LIST. The Title List menu appears. If you are using a DVDRW (VR mode), press TOOLS and select either “Original” or “Playlist” from the TOOLS menu to change the Title List, if necessary. 1.5/4.7GB 2ch Title You can enter up to 64 characters for a name. The title name will be displayed in the Title List menu. My Movies ORIGINAL 1 Sort b Press M/m to select the title, then press ENTER. The sub-menu appears. c Press M/m to select “Protect Title,” then press ENTER. The following display appears. Protect Select the protection status for this title. 1 -RW.VR TITLE LIST My Movies 1 2ch 1:00PM - 2:00PM 9/15 2 5ch 8:00PM - 9:00PM 9/17 Number 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 5 25ch 8:00PM - 8:30PM 10/15 6 L2 9:00PM - 9:30PM 10/19 7 8ch 9:00PM - 9:30PM 10/26 8 125ch 10:00AM - 10:30AM 10/28 Title Basic Editing 2ch 1:00PM - 2:00PM Mon 9/15 1.5/4.7GB Date Sort 64 ORIGINAL On Off d Press </, to select “On,” then press ENTER. The protection is set. To cancel the protection 1 2 3 Select the protected title in step 2. Press M/m to select “Protect Title,” then press ENTER. Press </, to select “Off,” then press ENTER. ◆ When the selected title is referred to by a Playlist Select “Close” as you are unable to delete an original title that is referred to by a Playlist. If you want to delete the original title, first delete the Playlist title. Then, delete the original title. z Hint To protect the entire disc If you are using a DVD-RW (Video mode) or DVD+RW, you can erase a title using the Disc Map (page 38). See page 72. Note You cannot protect Playlist titles. Erasing multiple titles (Erase Titles) You can erase more than two titles at one time using the TOOLS menu. Erasing a title (Erase) You can erase titles individually using the sub-menu. ◆For DVD-RWs (VR mode): Note that you are unable to erase the original title if there is a Playlist title derived from the original title. a Press TITLE LIST. The Title List menu appears. If you are using a DVDRW (VR mode), press TOOLS and select either “Original” or “Playlist” from the TOOLS menu to change the Title List, if necessary. ◆For DVD-RWs (VR mode): Note that you are unable to erase the original title if there is a Playlist title derived from the original title. a Press TITLE LIST. The Title List menu appears. If you are using a DVDRW (VR mode), press TOOLS and select either “Original” or “Playlist” from the TOOLS menu to change the Title List, if necessary. -RW.VR TITLE LIST -RW.VR TITLE LIST ORIGINAL 2ch 1:00PM - 2:00PM 9/15 Date 2 5ch 8:00PM - 9:00PM 9/17 Number 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 5 25ch 8:00PM - 8:30PM 10/15 6 L2 9:00PM - 9:30PM 10/19 7 8ch 9:00PM - 9:30PM 10/26 8 125ch 10:00AM - 10:30AM 10/28 Sort Title b Press M/m to select the title you want to erase, then press ENTER. The sub-menu appears. c Press M/m to select “Erase,” then press ENTER. The display asks for confirmation. d Press </, to select “OK,” then press ENTER. The title is erased. ◆ When the selected title is protected • To continue the procedure, press , to select “Change.” The protection display appears. Select “Off” by pressing </,, then press ENTER. • To cancel the procedure, select “Close” by pressing </,, then press ENTER. 1.5/4.7GB 2ch 1:00PM - 2:00PM 9/15 Date 2 5ch 8:00PM - 9:00PM 9/17 Number 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 5 25ch 8:00PM - 8:30PM 10/15 6 L2 9:00PM - 9:30PM 10/19 7 8ch 9:00PM - 9:30PM 10/26 8 125ch 10:00AM - 10:30AM 10/28 Sort 1.5/4.7GB 1 My Movies 1 Title My Movies ORIGINAL Editing a DVD ◆For DVD-Rs: Note that erasing titles on a DVD-R does not increase available disc space. ◆For DVD-Rs: Note that erasing titles on a DVD-R does not increase available disc space. b Press TOOLS. The TOOLS menu appears. c Press M/m to select “Erase Titles,” then press ENTER. The display for selecting titles to be erased appears. Erase Titles Select the titles to erase. 1 2ch 1:00PM - 2:00PM 9/15 2 5ch 8:00PM - 9:00PM 9/17 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 5 25ch 8:00PM - 8:30PM 10/15 Cancel d Press M/m to select the title, then press ENTER. A check mark appears in the check box next to the selected title. To clear the check mark, press ENTER again. Erase Titles Select the titles to erase. OK 1 2ch 1:00PM - 2:00PM 9/15 2 5ch 8:00PM - 9:00PM 9/17 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 5 25ch 8:00PM - 8:30PM 10/15 Cancel List Reset All ,continued Basic Editing 65 To list all of the titles to be erased, select “List.” To clear all the check marks, select “Reset All.” e Repeat step 4 to select all the titles you want to erase. ◆ When the selected title is protected The display asks for confirmation. c Press M/m to select “A-B Erase,” then press ENTER. The display for setting point A appears. The selected title plays in the background. The slider indicates the current playback point. A-B Erase (Set point A) 2 5ch 8:00PM - 9:00PM • To continue the procedure, press , to select “Change.” The protection display appears. Select “Off” by pressing </,, then press ENTER. • To cancel the procedure, select “Close” by pressing </,, then press ENTER. ◆ When the selected title is referred to by a Playlist Select “Close” as you are unable to delete an original title that is referred to by a Playlist. If you want to delete the original title, first delete the Playlist title. Then, delete the original title. f Press </, to select “OK,” then press ENTER. The display asks for confirmation. To return to the display for selecting titles, select “View All.” g Press </, to select “OK,” then press ENTER. z Hint If you are using a DVD-RW (Video mode) or DVD+RW, you can erase a title using the Disc Map (page 38). Erasing a section of a title (A-B Erase) A 0:12:34 B – :– –:– – Playback point ◆ When the selected title is protected The display asks for confirmation. • To continue the procedure, press </, to select “Change.” The protection display appears. Select “Off” by pressing </,, then press ENTER. • To cancel the procedure, select “Close” by pressing </,, then press ENTER. ◆ When the selected title is referred to by a Playlist Select “Close” as you are unable to delete an original title that is referred to by a Playlist. If you want to delete a section of the original title, first delete the Playlist title. Then, delete the section. d While watching the playback picture, set point A using H PLAY, X PAUSE, and m/M, then press ENTER. The display for setting point B appears, and the title continues to play in the background. A-B Erase (Set point B) 2 5ch 8:00PM - 9:00PM You can erase a section of a title using the sub-menu. ◆For original titles in a DVD-RW (VR mode): Note that you are unable to erase the original title if there is a Playlist title derived from the original title. A 0:12:34 B 0:23:45 A a Press TITLE LIST. The Title List menu appears. If you are using a DVDRW (VR mode), press TOOLS and select either “Original” or “Playlist” from the TOOLS menu to change the Title List, if necessary. -RW.VR TITLE LIST ORIGINAL My Movies 1.5/4.7GB 1 2ch 1:00PM - 2:00PM 9/15 Date 2 5ch 8:00PM - 9:00PM 9/17 Number 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 Sort Title 5 25ch 8:00PM - 8:30PM 10/15 6 L2 9:00PM - 9:30PM 10/19 7 8ch 9:00PM - 9:30PM 10/26 8 125ch 10:00AM - 10:30AM 10/28 b Press M/m to select the title, then press ENTER. The sub-menu appears. 66 Basic Editing e While watching the playback picture, set point B using H PLAY, X PAUSE, and m/M, then press ENTER. The display asks for confirmation. A-B Erase Erase the scene between A 0:12:34 and B 0:23:45? OK Cancel Preview Change A Change B To preview, select “Preview.” To reset either point A or B, select “Change A” or “Change B.” f Press </M/m/, to select “OK,” then press ENTER. The scene is erased, and the display asks whether to erase another scene. g To exit, press </, to select “No,” then press ENTER. The display returns to the Title List menu. To continue, select “Yes” and repeat the steps above. Notes • Images or sound may be momentarily interrupted at the point where you erase a section of a title. • Sections shorter than five seconds may not be erased. Creating chapters manually Advanced Editing (Playlist Edit) This section explains how to create a Playlist, and then covers available edit functions for the created Playlist. Playlist titles can be created from scenes that are selected original titles or other Playlist titles. Since edits to the Playlist does not affect the original title, you can redo editing as many times as you like. To create a Playlist title, you will do the following. 1.Select a title or titles for editing m 2.“Capture” multiple scenes from the selected title(s) m 3.Confirm the scenes on the Scene List Editing a DVD You can manually insert a chapter mark at any point you like. m Press CHAPTER MARK during playback at the point where you want to divide the title into chapters. Each time you press the button, “Marking…” appears on the screen and the scene to the left and right of the mark becomes a chapter. 4.If necessary, edit the scenes on the Scene List m 5.Connect scenes to create a “Playlist” title Marking... To erase chapter marks TITLE LIST You can combine two chapters by erasing a chapter mark during playback. 1 Press . PREV or > NEXT to search for a chapter number. 2 Press CHAPTER ERASE while displaying the chapter you want to erase. The current playing chapter combines with the previous chapter. TOOLS </M/m/,, ENTER m/M X PAUSE H PLAY Notes • Playback may momentarily stop when inserting a chapter mark. • A message will appear when no more chapter marks can be added. In this case, you may not be able to record or edit the disc. Creating a Playlist title from other titles Collect your favourite scenes from original titles or other Playlist titles to create a new Playlist title. You can rearrange the order of the scenes, delete scenes, or edit the scenes as well. a Press TITLE LIST. The Title List (Original) menu or the Title List (Playlist) menu appears. Example: The Title List (Original) menu. ,continued Advanced Editing (Playlist Edit) 67 -RW.VR TITLE LIST ORIGINAL My Movies 1.5/4.7GB 1 2ch 1:00PM - 2:00PM 9/15 Date 2 5ch 8:00PM - 9:00PM 9/17 Number 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 5 25ch 8:00PM - 8:30PM 10/15 6 L2 9:00PM - 9:30PM 10/19 7 8ch 9:00PM - 9:30PM 10/26 8 125ch 10:00AM - 10:30AM 10/28 Sort Title b Press TOOLS. g Press M/m to select one of the titles, then press ENTER. The sub-menu appears. ◆ To add the entire title as one scene to the Playlist title Select “Capture All” and go to step 14. h Press M/m to select “Capture,” then press ENTER. The display for setting the start point (IN) appears. The selected title starts to play in the background. The TOOLS menu appears. c Press M/m to select “Create Playlist,” then press ENTER. Capture (Set IN point) 2 5ch 8:00PM - 9:00PM The display for selecting titles appears. Create Playlist Select the titles you want to capture. Original Cancel 1 2ch 1:00PM - 2:00PM 9/15 2 5ch 8:00PM - 9:00PM 9/17 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 5 25ch 8:00PM - 8:30PM 10/15 6 L2 9:00PM - 9:30PM 10/19 IN0:10:26 OUT- : - - : - - Select All i While watching the playback picture, select the start of the scene using H PLAY, X PAUSE, and m/M, then press ENTER. d Press M/m to select the title you want to include in the Playlist title, then press ENTER. The display for setting the end point (OUT) appears, and the title continues to play in the background. Capture (Set OUT point) 2 5ch 8:00PM - 9:00PM A check mark appears in the check box next to the selected title. To clear the check mark, press ENTER again. Create Playlist Select the titles you want to capture. IN0:10:26 OUT0:23:45 IN OK Original Cancel 1 2ch 1:00PM - 2:00PM 9/15 2 5ch 8:00PM - 9:00PM 9/17 3 12ch 9:00AM - 9:30AM 9/25 4 3ch 8:00PM - 8:30PM 9/25 5 25ch 8:00PM - 8:30PM 10/15 6 L2 9:00PM - 9:30PM 10/19 Select All Reset All j While watching the playback picture, select the end point of the scene using H PLAY, X PAUSE, and m/M, then press ENTER. The display asks for confirmation. To select all of the titles, select “Select All.” Capture Do you want to capture the scene between IN 0:10:26 and OUT 0:23:45? e Repeat step 4 when adding more titles. To go to the next page, press m. To clear all the check marks, select “Reset All.” f Press </, to select “OK,” then press ENTER. OK Cancel Preview Change IN Change OUT To view the selected scene, select “Preview.” To reset either the IN or OUT point, select “Change IN” or “Change OUT.” The list of selected titles appears. k Press </, to select “OK,” then press ENTER. Create Playlist - Selected Titles Select a title to start capturing. 1 2ch 1:00PM - 2:00PM 9/15 2 5ch 8:00PM - 9:00PM 9/17 Cancel The selected portion is captured as a scene, and the display asks whether to continue scene capture. Add Title Capture Do you want to select another scene? To add another title, select “Add Title.” 68 Advanced Editing (Playlist Edit) More No More New Title l Press </, to select an option on the screen, then press ENTER. To capture a scene from the same title, select “More,” and repeat the steps above. To capture a scene from another title, select “New Title,” and repeat the steps above. m To end scene capture, press </, to select “No More” and press ENTER. ◆ To erase the scene (Erase) A Press M/m to select the scene you want to erase, then press ENTER. The sub-menu appears. B Press M/m to select “Erase,” then press ENTER. C When the display asks for confirmation, press </, to select “OK,” then press ENTER. ◆ To check the captured scenes in a single title ◆ To change the scene contents (Change IN/ Change OUT) A Press M/m to select a title from the list of selected titles, then press ENTER. The sub-menu appears. A Press M/m to select the scene you want to change, then press ENTER. The sub-menu appears. B Press M/m to select “Check Scenes,” then press ENTER. The thumbnail pictures of the captured scenes within the title appear. B Press M/m to select “Change IN,” then press ENTER. The display for setting the IN point appears. The display returns to the list of selected titles. 1 Close n Press </M/m/, to select “Scene List,” then press ENTER. The Scene List menu appears with all of the selected scenes. Total number of scenes Total duration of the selected scene Scene List Total 0:33:28 5ch 8:00PM - 9:00PM Scenes 2 OK -1 0:10:26 - 0:23:45 5ch 2 8:00PM - 9:00PM Quit -2 0:25:00 - 0:45:08 Add Preview ◆ To change the scene order (Move) A Press M/m to select the scene you want to move, then press ENTER. The sub-menu appears. B Press M/m to select “Move,” then press ENTER. The display for selecting the insertion point appears. Move 5ch 1 8:00PM - 9:00PM -1 Cancel 0:10:26 - 0:23:45 Where do you want to move this scene to? 5ch 2 2 5ch 8:00PM - 9:00PM 2 5ch 8:00PM - 9:00PM 2 1 Editing a DVD Capture (Set IN point) Check Scenes 8:00PM - 9:00PM -2 0:25:00 - 0:45:08 IN0:10:26 OUT0:23:45 C Repeat steps 9 to 14. To reset the OUT point, select “Change OUT,” then repeat steps 10 to 14. The display returns to the Scene List menu. ◆ To add another scene Press </M/m/, to select “Add,” then press ENTER. Repeat steps above. ◆ To preview the entire Playlist title Press </M/m/, to select “Preview,” then press ENTER. The captured scenes start to play in the listed order. When the playback is finished, the display returns to the Scene List menu. o Press </, to select “OK,” then press ENTER. The scenes are connected to create a new Playlist title, and the display for entering the title name appears. ◆ To enter a new name Select “Enter” and follow the explanations on page 34. ◆ To use the default name Press </, to select “OK,” then press ENTER. A new Title List menu appears with the title of the entered name. z Hint C Press M/m to select the insertion point, then press ENTER. The scene moves to its new position, and the display returns to the Scene List menu. When a Playlist title is created, the “IN” point and “OUT” point will become chapter marks, and each scene will become a chapter. Notes • You can capture, move, or change the IN and OUT points for a maximum of 50 scenes per title. • The picture may pause when the edited scene is played. ,continued Advanced Editing (Playlist Edit) 69 Moving a Playlist title (Move Title) -RW.VR TITLE LIST Sort Date My Movies PLAYLIST 1.5/4.7GB 1 2ch 1:00PM - 2:00PM 9/15 2 5ch 8:00PM - 9:00PM 9/17 Number You can change the Playlist title order within the Title List (Playlist). Title a Press TITLE LIST. The Title List menu appears. If the Title List (Original) menu appears, press TOOLS, and select “Playlist” from the TOOLS menu. -RW.VR Sort Date TITLE LIST PLAYLIST My Movies 1.5/4.7GB 1 2ch 1:00PM - 2:00PM 9/15 2 5ch 8:00PM - 9:00PM 9/17 Number Title b Press M/m to select the title, then press ENTER. The sub-menu appears. c Press M/m to select “Divide Title” then press ENTER. The display setting the dividing point appears. The selected title starts to play in the background. Divide 1 2ch 1:00PM - 2:00PM b Press < to select the sort buttons. c Press M/m to select “Number,” then press ENTER. d Press M/m to select the title you want to move, then press ENTER. The sub-menu appears. e Press M/m to select “Move Title,” then press ENTER. The display for moving titles appears. 0:12:34 d While watching the picture on the screen, move the playback point using H PLAY, X PAUSE, and m/M. e Press ENTER at the point where you want to divide the title. The display asks for confirmation. Divide f Press M/m to select the new location, then press ENTER. Do you want to divide this title at this point? OK Change Cancel The title moves to its new location, and the display returns to the new Title List (Playlist) menu. To change the dividing point, select “Change.” Dividing a Playlist title (Divide Title) f Press </, to select “OK,” then press ENTER. The display asks if you want to enter a new name. You can divide a Playlist title into two Playlist titles. For example, if a Playlist title contains two football matches, you can divide the title where the first match ends. a Press TITLE LIST. The Title List menu appears. If the Title List (Original) menu appears, press TOOLS, and select “Playlist” from the TOOLS menu. 70 Advanced Editing (Playlist Edit) ◆ To enter a new name Select “Yes” and follow the explanations on page 34. ◆ To use the same name as before Select “No.” The title is divided and the Title List menu appears with the two divided titles. Combining multiple Playlist titles (Combine Titles) f Press , to select “OK,” then press ENTER. The display asks for confirmation. Combine Combine the titles in the following order. You can add new contents to an existing Playlist title by combining the title with other Playlist titles. 1 1 2ch 1:00PM - 2:00PM 2 2 2ch 1:00PM - 2:00PM 9/28 3 3 2ch 1:00PM - 2:00PM 10/ 5 a Press TITLE LIST. OK The Title List menu appears. If the Title List (Original) menu appears, press TOOLS, and select “Playlist” from the TOOLS menu. -RW.VR TITLE LIST PLAYLIST My Movies 1.5 / 4.7GB 1 2ch 1:00PM - 2:00PM 9/15 Date 2 5ch 8:00PM - 9:00PM 9/17 Number 3 2ch 1:00PM - 2:00PM 9/28 4 2ch 1:00PM - 2:00PM 10/ 5 Sort Title 9/15 Change To change the selection, select “Change.” g Press </, to select “OK,” then press ENTER. The display for selecting a title name from among the selected titles appears. To enter a new name, select “Enter Text,” and follow the explanations on page 34. The titles are combined, and the display returns to the Title List menu. b Press TOOLS. The TOOLS menu appears. c Press M/m to select “Combine Titles,” then press ENTER. Editing a DVD h Press M/m to select a name, then press ENTER. Additional Playlist edit functions The display for selecting titles appears. Combine Select the titles to combine. 1 2ch 1:00PM - 2:00PM 9/15 2 5ch 8:00PM - 9:00PM 9/17 3 2ch 1:00PM - 2:00PM 9/28 4 2ch 1:00PM - 2:00PM 10/ 5 Cancel d Press M/m to select the title, then press ENTER. A number appears next to the selected title, indicating the order in which you selected the title. You can also do the following edits for Playlists. – Label a Playlist title (page 64). – Erase a Playlist title (page 65). – Erase multiple Playlist titles (page 65). – Erase a section of a Playlist title (A-B Erase) (page 66). – Create chapters in a title (page 67). To perform these edits, press TITLE LIST * and then follow the same steps for these functions explained in “Basic Editing” (page 64). * If the Title List (Original) menu appears, press TOOLS and select “Playlist” from the TOOLS menu. Note Combine Erasing Playlist titles will not free up disc space. Select the titles to combine. 1 1 2ch 1:00PM - 2:00PM 9/15 2 5ch 8:00PM - 9:00PM 9/17 3 2ch 1:00PM - 2:00PM 9/28 4 2ch 1:00PM - 2:00PM 10/ 5 Cancel Reset All To cancel the selection, move the cursor to the selected title by pressing M/m, then press ENTER again. e Repeat step 4 to select all the titles you want to combine. To list the titles to be combined, select “List.” To cancel all of the selections, select “Reset All.” Advanced Editing (Playlist Edit) 71 Labeling, Protecting, or Finalizing the Disc c Press M/m to select “Disc Name,” then press ENTER. The display for entering a disc name appears. Input Disc Name Using the Disc Information display, you can label, protect, or finalize your disc. You can even erase the entire disc except for the protected titles. This section explains settings effective for the entire disc. "A" 1 . , - 1 2 A B C 2 3 D E 3 F 4 G H I 4 5 J L 5 K 6 M N O 6 Back 7 P Q R S Clear All 8 T U V 8 9 W X Y Z Space 0 0 "a" 7 Symbol 9 Cancel Finish d Enter a name by following the explanation on page 34. The Disc Information display appears with the new disc name. Disc Information Close DiscName Movie TOOLS </M/m/,, ENTER RETURN Media DVD-RW Format Title no. Original 3 / Playlist 2 Disc Name VR Protect Disc e Press RETURN to turn off the display. Note The disc name will not appear when the disc is played on a different recorder. Labeling a disc (Disc Name) Protecting a disc (Protect Disc) You can enter up to 64 characters for a disc name (the actual number of displayed characters will vary). The disc name will be displayed in the Title List, etc. You can protect an entire disc. To protect individual titles, see page 64. Note that this protection is effective only for inadvertent edit commands and erasure. a Press TOOLS while the disc is in the recorder. a Press TOOLS while the disc is in the recorder. The TOOLS menu appears. The TOOLS menu appears. b Press M/m to select “Disc Info.,” then press ENTER. The Disc Information display appears. Example: When the inserted disc is a DVD-RW (VR mode). b Press M/m to select “Disc Info.,” then press ENTER. The Disc Information display appears. Disc Information Close DiscName Movie Disc Information Close DiscName Media DVD-RW Title no. Original 3 / Playlist 2 Disc Name VR Protect Disc Protected Not Protected Finalize Date Erase All 9/15/2003 ~ 10/28/2003 HQ : 0H30M Remainder LP : 1H30M 72 Format HSP : 0H45M EP : 2H00M SP : 1H00M SLP : 3H00M 2. 3 / 4. 7GB Format Labeling, Protecting, or Finalizing the Disc Media DVD-RW Title no. Original 3 / Playlist 2 Format Disc Name VR Protect Disc Protected Not Protected Finalize Date Erase All 9/15/2003 ~ 10/28/2003 HQ : 0H30M Remainder LP : 1H30M HSP : 0H45M EP : 2H00M SP : 1H00M SLP : 3H00M 2. 3 / 4. 7GB Format c Press M/m to select “Protect Disc,” then press ENTER. The display for setting disc protection appears. Protect Disc Select the protection status for this disc. Protect Don't Protect d Press </, to select “Protect,” then press ENTER. The display returns to the Disc Information display. e Press RETURN to turn off the display. a Press TOOLS while the disc is in the recorder. The TOOLS menu appears. b Press M/m to select “Disc Info.,” then press ENTER. The Disc Information display appears. Disc Information Close DiscName Movie Media DVD-RW Title no. Original 3 / Playlist 2 Repeat steps 1 to 3 above. The display for setting disc protection appears. 2 Press </, to select “Don’t Protect.” The display returns to the Disc Information display. 3 Press RETURN to turn off the display. Protect Disc Finalize Date Erase All 9/15/2003 ~ 10/28/2003 HSP : 0H45M EP : 2H00M SP : 1H00M SLP : 3H00M 2. 3 / 4. 7GB Format c Press M/m to select “Finalize,” then press ENTER. The display shows the approximate time required for finalizing and asks for confirmation. Finalize About xx min is needed for finalizing this disc. Cannot cancel finalizing during transaction. Do you want to finalize? Finalizing a disc (Finalize) Finalizing is necessary when you play discs recorded with this recorder on other DVD equipment. Before finalizing, check the differences between the disc types on the table below. When you finalize a DVD-RW (Video mode), DVD+RW, or DVD-R, a DVD menu will be automatically created, which can be displayed on other DVD equipment. When a finalized disc is in the recorder, the FINALIZED indicator lights up on the front panel. Differences between the disc types Finalizing is unnecessary when playing a disc on VR format compatible equipment. You may need to finalize the disc depending on the DVD equipment, or if the recording time is short. You can edit or record on the disc even after finalizing. Finalizing is unnecessary, since DVD+RWs are automatically finalized when removed from the recorder. However, you may need to finalize the disc by following the steps below for certain DVD equipment, or if the recording time is short. You can edit or record on the disc even after finalizing. Finalizing is necessary when playing on equipment other than this recorder. After finalizing, you cannot edit or record on the disc. If you want to record on it again, reformat the disc (page 74). However, all contents recorded on the disc will be erased. Finalizing is necessary when playing on equipment other than this recorder. After finalizing, you cannot edit or record on the disc. OK Editing a DVD 1 VR Protected Not Protected HQ : 0H30M Remainder LP : 1H30M To cancel the disc protection Format Disc Name Cancel d Press </, to select “OK,” then press ENTER. The recorder starts finalizing the disc. To unfinalize a disc If you cannot record or edit on the DVD-RW (VR mode) that has been finalized with other DVD equipment (a message appears), unfinalize the disc. Select “Unfinalize” in step 3 above. z Hint You do not need to finalize a disc again once the disc has been finalized with this recorder. Notes • Depending on the condition of the disc, recording, or the DVD equipment, discs may not play even when the discs are finalized. • The recorder may not be able to finalize the disc if it was recorded on another recorder. Erasing all the titles on the disc (Erase All) You can erase all the titles on the disc except the titles you have set protection. The disc name and recording format remain the same. a Press TOOLS while the disc is in the recorder. The TOOLS menu appears. ,continued Labeling, Protecting, or Finalizing the Disc 73 b Press M/m to select “Disc info.,” then press ENTER. The Disc Information display appears. ◆ When you place a DVD-RW and set “Format Disc” to “Selectable” in Options Setup The display asks you to select the recording format. Format Disc Information Close Select the recording format. DiscName Movie Media Title no. DVD-RW Format Video Protect Disc Original 3 / Playlist 2 Protected Not Protected Finalize Date Erase All 9/15/2003 ~ 10/28/2003 HQ : 0H30M Remainder LP : 1H30M VR Disc Name VR HSP : 0H45M EP : 2H00M SP : 1H00M SLP : 3H00M 2. 3 / 4. 7GB Press </, to select “VR” or “Video,” then press ENTER. Format The recorder starts formatting the disc. c Press M/m to select “Erase All,” then press ENTER. The display asks for confirmation. When there is a protected title on the disc, a list of protected titles appears. Erase All Titles Do you want to erase all the titles? OK Cancel d Press </, to select “OK,” then press ENTER. The titles are erased. Reformatting a disc (Format) By reformatting, you can change the recording format of DVDRWs, or record again on DVD-RWs (Video mode) that have been finalized. Make sure nothing important is left on the disc, as all the disc contents will be erased. For DVD+RWs, reformat the disc if you want to create a blank disc. a Press TOOLS while the disc is in the recorder. The TOOLS menu appears. b Press M/m to select “Disc Info.,” then press ENTER. The Disc Information display appears. Disc Information Close DiscName Movie Media DVD-RW Title no. Original 3 / Playlist 2 Format Disc Name VR Protect Disc Protected Not Protected Finalize Date Erase All 9/15/2003 ~ 10/28/2003 HQ : 0H30M Remainder LP : 1H30M HSP : 0H45M EP : 2H00M SP : 1H00M SLP : 3H00M 2. 3 / 4. 7GB Format c Press M/m to select “Format,” then press ENTER. The display asks for confirmation. d Press </, to select “OK,” then press ENTER. 74 Labeling, Protecting, or Finalizing the Disc Notes • Even when you have set protection for the title, all the contents will be erased after formatting the disc. • A protected disc cannot be reformatted (DVD-RW in VR mode only). Before Recording/Editing You can record from connected equipment, such as a digital video camera. The recorder has a DV IN jack that inputs digital signals, and LINE jacks that input/output analogue signals. The DV IN jack on this recorder conforms to the i.LINK standard. You can connect other equipment that has an i.LINK (DV) jack. For more information, see “About i.LINK” (page 106). If you plan to do additional editing on a disc after the initial dub, use the DV IN jack and record on a DVD-RW in VR mode. ◆When recording from the DV IN jack See “Preparing for recording using the DV IN jack” below. ◆When recording from the LINE IN jacks See “Recording From Equipment Connected to the LINE IN Jacks” (page 88). Preparing for recording using the DV IN jack You can connect a digital video camera to the DV IN jack on the recorder to record or edit from a DV/Digital8 format tape. Operation is smooth because the recorder will fast forward and rewind the tape for you – you do not need to operate your digital video camera. Do the following to start using the DV Edit functions of this recorder. See also the instruction manual supplied with the digital video camera before connecting. ◆If you connect a digital video camera but cannot use the DV Edit functions See “Recording from connected equipment” (page 88). Notes • Before Recording/Editing . . . . . . . . . .page 75 • The DV IN jack on this recorder is for input only. If you want to have the recorder output signals, for example, when you use this recorder as source player, connect other equipment to this recorder’s LINE OUT jacks. • Only DVC-SD format signals can be input to the DV IN jack on this recorder. Do not connect a MICRO MV format digital video camera even if it has an i.LINK jack. • Recording may be limited if the images on the tape contain copyright protection signals. Connecting a Digital Video Camera or Other Equipment Connecting a Digital Video Camera or Other Equipment • Available DV Dubbing Functions . . . . .page 77 • Recording an Entire DV/Digital8 Format Tape (ONE TOUCH DUB) . . . . . . . . . . . . . . . . . . . . . .page 78 • Program Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 79 • Advanced Program Edit . . . . . .page 81 • Re-editing the “program” in the DV/D8 Edit List . . . . . . . . . . . . . . . . . . . . . .page 84 • Creating a Copy of the Edited Contents (Copy Dubbing) . . . . . . . . . . . . . . . . . . . . . . . . . . . .page 86 • Recording From Equipment Connected to the LINE IN Jacks . . . . . . . . . . . . . . . . . . . . . .page 88 ,continued Before Recording/Editing 75 c Press Z OPEN/CLOSE to close the disc tray. Hookups DVD recorder To DV IN Wait until “LOAD” disappears from the front panel display. If you use an unused DVD, formatting starts automatically. When using an unused DVD-RW, select the recording format, VR or Video. d Insert the source DV/Digital8 format tape into the digital video camera. For the recorder to record or edit, the digital video camera must be set to video playback mode. i.LINK cable (not supplied) e Press INPUT SELECT on the remote repeatedly to select “DV.” The front panel display changes as follows. Channel number DV output L1 L2 L3 DV Digital video camera f Press REC MODE on the remote repeatedly to select the recording mode. The recording mode changes as follows: : Signal flow HQ Z OPEN/CLOSE HSP SP LP EP SLP g Select the audio input for the digital video camera using the TOOLS menu. A Press TOOLS. B Press M/m to select “DV/D8 Audio Input,” then press ENTER. TOOLS M/m, ENTER REC MODE INPUT SELECT C Press M/m to select the item, then press ENTER. • Stereo1 (default) • Mix (both stereo 1 and stereo 2) • Stereo2 You are ready to start recording. z Hints • You can adjust the settings for the recording picture before recording. See “Adjusting the Recording Picture Quality and Size” (page 46). • If you plan to re-edit the “program” (page 77), insert a DVD-RW and format it in VR mode. Notes a Turn on your TV and this recorder, then set the TV to the connected channel (“VIDEO” etc.). b Press Z OPEN/CLOSE, and place a recordable disc on the tray. Make sure that the disc has enough free space to record the contents of your tape. 76 Before Recording/Editing • You cannot connect more than two pieces of digital video equipment to the recorder. • Depending on the digital video equipment, you may not be able to control the equipment. • You cannot control the recorder using another device or another recorder of the same model. • You cannot record date, time or the contents of the cassette memory onto the disc. • If you record from a DV/Digital8 format tape with a sound track that is recorded in multiple sampling frequencies (48 kHz, 44.1 kHz, or 32 kHz), no sound will be output when playing back the switched point on the disc. • In order to use this recorder’s Auto Scene Chaptering feature, be sure to correctly set the clock on your digital video camera before shooting. • The recorded picture may be momentarily affected if the picture size of the source image changes, or if there is nothing recorded on the tape. Available DV Dubbing Functions ◆About the “DV/D8 Edit List” The “DV/D8 Edit List” contains the “programs.” If you re-edit the program, the re-edited program is stored in the DV/D8 Edit List, but the original program is lost. You can store up to 20 programs in the DV/D8 Edit List. ◆One Touch Dub (page 78) Records the entire contents of a DV/Digital8 format tape to a disc of your choice with a single touch of the ONE TOUCH DUB button. ◆Program Edit (page 79) Allows you to select scenes from a DV/Digital8 format tape, and then record the selected scenes to a disc of your choice. As you select the scenes, you will create a “program” (see below), which will then be used to dub the selected scenes to a disc. Before you dub the scenes, you can rearrange the order and make other changes using the “Scene List” (see below). ◆Re-editing the “program” in the DV/D8 Edit List (DVD-RW in VR mode only) (page 84) Allows you to select the “program” (see below) created during One Touch Dub or Advanced Program Edit from the “DV/D8 Edit List” (see below), and make further edits before coping the contents to a disc. You can delete or create new scenes, or rearrange the order of existing scenes. ◆Copy Dubbing (page 86) Allows you to make duplicate copies of the “programs” (see below) in the “DV/D8 Edit List” (see below) to a disc of your choice. When making copies, you will need the original DV/ Digital8 format tapes used to create the “program.” About “programs” DV12/11/02 1:00PM - 12/11/02 7:05PM 1H16M 6/10 DV12/24/02 11:34AM - 12/25/02 1:24PM 1H24M 6/18 1 Disc mark 2 Program name 3 Total playing time 4 Date of editing or recording ◆About the “Scene List” The contents of the programs are contained in the “Scene List.” A thumbnail of each scene, as well as the length of the scene is displayed in the list. You can add or delete scenes, or change the order of the scenes. 50 scenes can be made for each program. Total 1:23:30 Scenes 20 SCENE LIST 1 0:00:30-0:00:52 Duration 0:00:22 2 0:01:40-0:06:23 Duration 0:06:43 3 0:07:07-0:10:51 Duration 0:03:44 4 0:11:40-0:16:19 Duration 0:04:39 OK Quit Add 1 Thumbnail picture 2 Time information 3 Total duration of the program 4 Total number of scenes Note After you make a dubbing, do not throw away or record over your tapes. You will need them later to make additional edits or copies. Connecting a Digital Video Camera or Other Equipment ◆Advanced Program Edit (page 81) Allows you to select scenes from a DV/Digital8 format tape by first recording the entire contents of the tape to a DVD-RW (VR mode), whereupon you can easily create a “program” (see below). By first copying the entire contents of the tape to a disc, the start and stop points on the tape automatically become scenes (you can also select scenes manually). These scenes are displayed in a “scene list” (see below). You can then delete, rearrange, or select new scenes to create a “program.” Once the “program” is complete, you will use it to copy the scenes to a disc of your choice from the “DV/D8 Edit List” (see below). Furthermore, you can also automatically create a Playlist of the edited scenes and save it on the DVD-RW (VR mode) you used to originally record the entire contents of the tape. DV/D8 EDIT LIST DV10/11/02 1:30PM - 11/12/02 4:46PM 1H12M 6/ 5 “Programs” are automatically created whenever you make a One Touch Dub, Program Edit, or Advanced Program Edit. These programs are stored in the “DV/D8 Edit List” (see below) and contain editing information such as which scenes have been selected, moved, or deleted. Programs are useful when you want to make duplicates of the edited contents because you do not have to select the same scenes again from the tape – just select the program. You can also re-edit the program to create different variations of the original program. Note that programs contain only the start and stop points of the scenes; they do not contain the actual scenes themselves so you need to use the original DV/Digital8 format tapes to copy a program to a disc. Available DV Dubbing Functions 77 Recording an Entire DV/ Digital8 Format Tape (ONE TOUCH DUB) • The recorder automatically records a blank for five minutes before it stops dubbing. When you press x REC STOP, the recorder stops recording, rewinds the tape, and turns off. You can record the entire contents of a DV/Digital8 format tape onto a disc with a single press of the ONE TOUCH DUB button. The recorder controls the digital video camera for the whole process, and completes the recording. Example for all disc types a a b b When using a DVD-RW (VR mode), chapter marks [b] are marked where the recordings start on the tape [a] (Auto Scene Chaptering). For other discs, the recorder marks chapters either in 6 or 15 minute intervals depending on the setting in “Auto Chapter” in Features Setup (page 97). Follow steps 1 to 7 of “Preparing for recording using the DV IN jack” (page 75), then press ONE TOUCH DUB on the front panel of the recorder. The recorder rewinds the tape and then starts recording the tape contents. When the recording is finished, the recorder rewinds the tape in the digital video camera, and turns off. To stop during recording Press x REC STOP. z Hints • The date and time of the recording made with your digital video camera is assigned as the program name in the DV/D8 Edit List (page 84) (example: DV 10/25/03 10:00PM – 10/31/03 11:30PM). • If you set “Finalize Disc” to “Auto” in Features Setup (page 98), the recorded disc will automatically be finalized after recording is finished. Notes • The recorder does not start One Touch Dub when you set “Add to Edit List” to “On” (default) in Features Setup (page 98) and there are already twenty programs on the recorder. In this case, the recorder beeps and the front panel display lights up. Delete unnecessary programs from the DV/D8 Edit List menu (page 84) and repeat the steps above. • When a blank space on the tape continues for more than five minutes, One Touch Dub ends automatically. • This function may not work with certain digital video cameras. In this case, follow the instructions of “Recording From Equipment Connected to the LINE IN Jacks” (page 88). • In order for a One Touch Dub recording to be added to the DV/D8 Edit List, “Add to Edit List” in Features Setup must be set to “On” (default) (page 98). 78 Recording an Entire DV/Digital8 Format Tape (ONE TOUCH DUB) Program Edit You can select scenes from a DV/Digital8 format tape, and then automatically record selected scenes to a disc of your choice. SYSTEM MENU Example for DVD-RWs (VR mode) </M/m/,, ENTER m/M RETURN a a H PLAY c b x REC STOP c b b To use this function, you will do the following: Connect your digital video camera and prepare for recording m Select and edit the scenes you want to dub Using the recorder’s remote control, you will fast forward or rewind the tape to select the scenes. At this point, the selected scenes are not copied to the disc. The recorder only remembers the IN and OUT points of the scenes that you selected for dubbing. You can also reset, erase, or change the order of the scenes. m Dub the selected scenes to a disc After you have selected the scenes, the recorder will fast forward and rewind the tape automatically and record the scenes to a disc of your choice. b Press M/m to select “DV/D8 EDIT,” then press ENTER. The DV/D8 Edit menu appears. DV/D8 EDIT Program Edit Select only the scenes you want to copy from the DV/D8 tape. Advanced Program Edit DV/D8 Edit List c Press M/m to select “Program Edit,” then press ENTER. The display asks whether to start selecting scenes. Scenes Selection Do you want to select a scene? Start Connecting a Digital Video Camera or Other Equipment When using a DVD-RW (VR mode), chapter marks [b] are marked where the recordings start on the tape [a] (Auto Scene Chaptering). Chapter marks are also inserted at the IN points of the selected scenes [c]. For other discs, the recorder marks chapters either in 6 or 15 minute intervals depending on the setting in “Auto Chapter” in Features Setup (page 97). a Follow steps 1 to 7 of “Preparing for recording using the DV IN jack” (page 75), then press SYSTEM MENU. Cancel ◆ If you have previously saved a program The display asks whether to edit an existing program or to create a new program. To resume editing the existing program, select “Saved Data.” d Press </, to select “Start,” then press ENTER. The display for setting the IN point (start of the scene on the tape) appears. e Press H PLAY to start playback of the tape in your digital video camera. The scene starts to play in the background. ,continued Program Edit 79 Select scene(Set IN point) Total 1:23:30 Scenes 20 SCENE LIST 0:00:30-0:00:52 Duration 0:00:22 1 2 0:01:40-0:06:23 Duration 0:06:43 3 0:07:07-0:10:51 Duration 0:03:44 4 0:11:40-0:16:19 Duration 0:04:39 OK Quit Add IN 0:00:30 OUT – :– –:– – f While watching the playback picture, search for the IN point by pressing m or M, then press ENTER. The display for setting the OUT point (end of the scene on the tape) appears. The scene starts to play in the background from the IN point. Select scene(Set OUT point) To edit the Scene List, select a scene by pressing </ M/m/,, and then press ENTER. When the submenu appears, select an edit option you want to apply to the scene. ◆ To erase the scene A Press M/m to select “Erase,” then press ENTER. B When the display asks for confirmation, press </, to select “OK,” then press ENTER. ◆ To move the scene IN 0:00:30 OUT 0:00:52 g While watching the playback picture, search for the OUT point by pressing m or M, then press ENTER. The display asks whether to add the selected scene to the Scene List menu. Scenes Selection OK Cancel Change IN B Press M/m to select the point, then press ENTER. The scene moves to the selected location. ◆ To reset the start or end of the scene Press M/m to select “Change IN” or “Change OUT,” then press ENTER. ◆ To preview the scene Press M/m to select “Preview,” then press ENTER. Do you want to capture the scene between IN 0:00:30 and OUT 0:00:52? Preview A Press M/m to select “Move,” then press ENTER. The display for selecting the scene insertion point appears. Change OUT To preview the scene, select “Preview.” To reset either the IN or OUT point, select “Change IN” or “Change OUT.” Repeat from step 5. h Press </M/m/, to select “OK,” then press ENTER. A new Scene List menu appears with the selected scene. To cancel, press </M/m/, to select “Quit” in the Scene List menu, then press ENTER. j When you finish editing the Scene List, press </M/m/, to select “OK,” then press ENTER. The display for entering a title name appears. Title Name Enter the title name. DV10/11/02 1:30PM - 11/12/02 4:46PM SCENE LIST 1 0:00:30-0:00:52 Duration 0:00:22 Total 0:00:22 Scenes 1 OK OK Enter Quit Add i Press </M/m/, to select “Add” and press ENTER. Then repeat steps 5 to 9 to select all the scenes you want to include. You can add up to 50 scenes to a title. To enter a new name, select “Enter,” and follow the explanations on page 34. k To use the default name, press </, to select “OK,” then press ENTER. The default title name is fixed, and the display asks whether to start recording. If you want to change the recording mode, press </, to move the cursor, then press M/m to select the mode. DV/D8 Dubbing Change the recording mode if necessary. Select "Start" to start dubbing. SP 80 Program Edit Start Cancel l Press </, to select “Start,” then press ENTER. The recorder starts recording the tape contents as programmed. To quit recording, press x REC STOP. Advanced Program Edit m When the recording is finished, press ENTER to select “Close.” The display returns to the DV/D8 Edit menu. n Press RETURN repeatedly to turn off the display. Notes a a c DVD-RW (VR) c New disc b b b When dubbing to a DVD-RW (VR mode), chapter marks [b] are marked where the recordings start on the tape [a] (Auto Scene Chaptering). Chapter marks are also inserted at the IN points of the selected scenes [c]. To use this function, you will do the following: Connect your digital video camera and prepare for recording m Record the entire contents of the DV/Digital8 tape to a DVD-RW (VR mode) m Select and edit the scenes you want to dub Taking advantage of the disc’s quick accessibility, you will select the scenes you want from the recorded DVD-RW. You do not have to fast forward or rewind the tape as explained in “Program Edit” (page 79). You can also reset, erase, or change the order of the scenes. m Connecting a Digital Video Camera or Other Equipment • The disc may not be recorded as programmed if the tape’s time code is not sequential or there are blanks between the recordings on the tape. In this case, follow the instructions of “Recording From Equipment Connected to the LINE IN Jacks” (page 88). • The start and end points of a program may be different from what you have set if the source DV/Digital8 format tape is in any of the following conditions: – Recording mode was changed during the recording. – There is a blank space in the recorded portion of the tape. • If you set the beginning of the tape as the IN point and the end point as the OUT point, the IN and OUT points may change slightly during dubbing. • You cannot set a scene shorter than one second. • This function may not work with certain digital video cameras. In this case, follow the instructions of “Recording From Equipment Connected to the LINE IN Jacks” (page 88). You can quickly edit a DV/Digital8 format tape by first copying the entire contents of the tape to a DVD-RW (VR mode) and then select the scenes you want from the disc. After you select the scenes, you can change discs and record the scenes to another disc of your choice. If necessary, you can also create a Playlist title of the selected scenes in the DVD-RW (VR mode). Dub the scenes to another disc After you have selected the scenes, you can dub the selected scenes to another disc of your choice. Or, you can create a Playlist of the selected scenes. ,continued Advanced Program Edit 81 Edit Select the method for dividing scenes. DV10/11/02 1:30PM - 11/12/02 Auto Manual Chapter 2 Cancel ◆ To create scenes automatically Press </, to select “Auto,” then press ENTER. The recorder divides the generated program into scenes, and the Scene List menu appears. SYSTEM MENU ◆ To create scenes manually </M/m/,, ENTER m/M RETURN x REC STOP a Follow steps 1 to 7 of “Preparing for recording using the DV IN jack” (page 75), then press SYSTEM MENU. Insert a DVD-RW (VR mode) into the recorder. Make sure that the disc has enough free space to record the contents of your tape. b Press M/m to select “DV/D8 EDIT,” then press ENTER. The DV/D8 Edit menu appears. A Press </, to select “Manual,” then press ENTER. The display for setting the IN point appears. The scene starts to play in the background. B While watching the playback picture, press m or M to search for the IN point, then press ENTER. The IN point is set, and the display for setting the OUT point (end of the scene) appears. C While watching the playback picture, press m or M to search for the OUT point, then press ENTER. The OUT point is set, and the display asks whether to add the selected scene to the Scene List menu. Scenes Selection Do you want to capture the scene between IN 0:00:30 and OUT 0:00:52? OK Cancel Preview Change IN Change OUT DV/D8 EDIT Select only the scenes you want to copy from the DV/D8 tape. Program Edit Advanced Program Edit DV/D8 Edit List c Press M/m to select “Advanced Program Edit,” then press ENTER. The display asks whether to start recording. DV/D8 Dubbing Change the recording mode if necessary. Select "Start" to start dubbing. SP Start Cancel If you want to change the recording mode, press </, to move the cursor, then press M/m to select the mode. d Press </, to select “Start,” then press ENTER. The recorder starts recording the tape contents. To quit recording, press x REC STOP. When recording is finished, the display asks if you want to create scenes within the generated program automatically or manually, or quit editing. 82 Advanced Program Edit • To preview the scene, select “Preview.” • To reset either the IN or OUT point, select “Change IN” or “Change OUT.” D Press </M/m/, to select “OK,” then press ENTER. A new Scene List menu appears with the selected scene. E Press </M/m/, to select “Add,” then press ENTER. The display for selecting the scene insertion point appears. F Press M/m to select the insertion point in the Scene List, then press ENTER. The display for setting the IN point (start of the scene) appears. G Repeat steps 2 to 6 to create all the scenes you want to add to the Scene List. You can add up to 50 scenes. ◆ To quit editing Press </, to select “Cancel,” then press ENTER. e To edit the Scene List, press </M/m/, to select a scene in the Scene List menu and press ENTER. When the sub-menu appears, select an edit option you want to apply to the scene. ◆ To erase the scene A Press M/m to select “Erase,” then press ENTER. B When the display asks for confirmation, press </, to select “OK,” then press ENTER. ◆ To move the scene A Press M/m to select “Move,” then press ENTER. The display for selecting the scene insertion point appears. B Press M/m to select the point, then press ENTER. The scene moves to the selected location. Notes • The disc may not be recorded as programmed if the tape’s time code is not sequential or there are blanks between the recordings on the tape. In this case, follow the instructions of “Recording From Equipment Connected to the LINE IN Jacks” (page 88). • You cannot set a scene to be shorter than one second. • The start and end point of a program may be different from what you have set if the source DV/Digital8 format tape is in any of the following conditions: – Recording mode was changed during the recording. – There is a blank space in the recorded portion. • This function may not work with certain digital video cameras. In this case, follow the instructions of “Recording From Equipment Connected to the LINE IN Jacks” (page 88). • In step 4, the recorder automatically records a blank for five minutes before it stops dubbing. When you press x REC STOP, the recorder stops recording. ◆ To reset the start or end of the scene Press M/m to select “Change IN” or “Change OUT,” then press ENTER. ◆ To preview the scene Press M/m to select “Preview,” then press ENTER. Connecting a Digital Video Camera or Other Equipment To cancel, press </M/m/, to select “Quit” in the Scene List menu, then press ENTER. f When you finish creating the Scene List, press </M/m/, to select “OK,” then press ENTER. The edited program is saved, and the display asks if you want to create a Playlist title. If you select “No,” the display returns to the DV/D8 Edit menu. Go to step 9. g Press </, to select “Yes,” then press ENTER. The display for entering a Playlist title name appears. To enter a new name, select “Enter,” and follow the explanations on page 34. h To use the default name, press </, to select “OK,” then press ENTER. A Playlist title of the default title name is created on the same disc, and the display returns to the DV/D8 Edit menu. You now have a disc containing both the entire contents of the DV/Digital8 format tape and a Playlist of the selected scenes. To edit the Playlist title, see “Advanced Editing (Playlist Edit)” (page 67). i Dub the selected scenes to a disc. Make copies of the selected scenes to a disc of your choice. Go to step 3 of “Creating a Copy of the Edited Contents (Copy Dubbing)” (page 86). Advanced Program Edit 83 Re-editing the “program” in the DV/D8 Edit List b Press M/m to select “DV/D8 EDIT,” then press ENTER. The DV/D8 Edit menu appears. DV/D8 EDIT Select only the scenes you want to copy from the DV/D8 tape. Program Edit Advanced Program Edit Each time you dub a DV/Digital8 format tape, the start and stop points of the selected scenes (called a “program”) are saved in a DV/D8 Edit List. You can make additional changes to these “programs” if they were created by One Touch Dub or Advanced Program Edit on a DVD-RW (VR mode). You can reset, erase, or change the order of the scenes and then dub the re-edited program to a disc of your choice. To use this function, you will do the following: Connect your digital video camera and prepare for editing DV/D8 Edit List c Press M/m to select “DV/D8 Edit List,” then press ENTER. The DV/D8 Edit List menu appears. A disc mark will appear next to the program that corresponds to the inserted disc. You can only edit the programs that display a disc mark (1). Be sure to use the original DV/Digital8 format tape and the DVD-RW (VR mode) that corresponds to the program in the DV/D8 Edit List. m Select a program from the DV/D8 Edit List DV/D8 EDIT LIST DV10/11/02 1:30PM - 11/12/02 4:46PM 1H12M 6/ 5 DV12/11/02 1:00PM - 12/11/02 7:05PM 1H16M 6/10 DV12/24/02 11:34AM - 12/25/02 1:24PM 1H24M 6/18 m Edit the program in the DV/D8 Edit List m 1 Disc mark Dub the selected scenes to a disc 2 Program name The recorder will fast forward and rewind the tape automatically and record the scenes to a disc of your choice. 3 Total playing time 4 Date of editing or recording d Press M/m to select the program you want to edit, then press ENTER. The sub-menu appears. e Press M/m to select “Edit,” then press ENTER. The Scene List menu appears with all the scenes the program contains. SYSTEM MENU Total duration of the program </M/m/,, ENTER m/M SCENE LIST 1 0:00:30-0:00:52 Duration 0:00:22 2 0:01:40-0:06:23 Duration 0:06:43 3 0:07:07-0:10:51 Duration 0:03:44 4 0:11:40-0:16:19 Duration 0:04:39 Total number of scenes Total 1:23:30 Scenes 20 OK Quit Add a Follow steps 1 to 4 of “Preparing for recording using the DV IN jack” (page 75), then press SYSTEM MENU. Be sure to use the original DV/Digital8 format tape and the DVD-RW (VR mode) that corresponds to the program in the DV/D8 Edit List. ◆ To add a new scene to the Scene List A Press </M/m/, to select “Add,” then press ENTER. The display for selecting the scene insertion point appears. B Press M/m to select the insertion point in the Scene List, then press ENTER. The display for setting the IN point (start of the scene) appears. 84 Re-editing the “program” in the DV/D8 Edit List C While watching the playback picture, press m or M to search for the IN point, then press ENTER. The IN point is set, and the display for setting the OUT point (end of the scene) appears. D While watching the playback picture, press m or M to search for the OUT point, then press ENTER. The OUT point is set, and the display asks whether to add the selected scene to the Scene List menu. Scenes Selection ◆ To reset the start or end of the scene Press M/m to select “Change IN” or “Change OUT,” then press ENTER. ◆ To preview the scene Press M/m to select “Preview,” then press ENTER. To cancel, press </M/m/, to select “Quit” in the Scene List menu, then press ENTER. h When you finish editing the Scene List, press </M/m/, to select “OK,” then press ENTER. The display asks if you want to make a Playlist title. If you select “No,” the edited program is saved, and the display returns to the DV/D8 Edit List. Note that the original program will be rewritten. To dub the selected scenes to a disc, go to step 4 of “Creating a Copy of the Edited Contents (Copy Dubbing)” (page 86). Do you want to capture the scene between IN 0:00:30 and OUT 0:00:52? OK Cancel Preview Change IN Change OUT • To preview the scene, select “Preview.” • To reset either the IN or OUT point, select “Change IN” or “Change OUT.” ◆ If you select a program that contains no scenes The display asks whether to generate scenes within the selected program. To generate scenes automatically, press </, to select “Auto,” then press ENTER. Scenes are generated and a new Scene List menu appears. To capture scenes manually, select “Manual,” then press ENTER. The display for adding a scene appears. Follow steps 3 to 5 above. You can add a maximum of 50 scenes. f Press M/m to select the scene you want to edit, then press ENTER. i Press </, to select “Yes,” then press ENTER. The display for entering a Playlist title name appears. To enter a new name, select “Enter,” and follow the explanations on page 34. j To use the default name, press </, to select “OK,” then press ENTER. A Playlist title of the default title name is created on the same disc, and the display returns to the DV/D8 Edit List. You now have a disc containing both the entire contents of the DV/Digital8 format tape and a Playlist of the selected scenes. To edit the Playlist title, see “Advanced Editing (Playlist Edit)” (page 67). k Dub the selected scenes to a disc. Make copies of the selected scenes to a disc of your choice. Go to step 4 of “Creating a Copy of the Edited Contents (Copy Dubbing)” (page 86). The sub-menu appears. g Press M/m to select the edit option you want to apply to the scene, then press ENTER. ◆ To erase the scene A Press M/m to select “Erase,” then press ENTER. B When the display asks for confirmation, press </, to select “OK,” then press ENTER. To preview a program After you edit a program, you can preview the changes you made. 1 While the DV/D8 Edit List is displayed, press M/ m to select the program, then press ENTER. 2 Press M/m to select “Preview,” from the submenu, then press ENTER. ◆ To move the scene A Press M/m to select “Move,” then press ENTER. The display for selecting the scene insertion point appears. B Press M/m to select the point, then press ENTER. The scene moves to the selected location. Connecting a Digital Video Camera or Other Equipment E Press </M/m/, to select “OK,” then press ENTER. A new Scene List menu appears with the selected scene. To add another scene, repeat from step 1. To create a Playlist title of the program After you edit a program, you can create a Playlist title of the edited program. The Playlist will be created on the inserted DVD-RWs (VR mode). 1 While the DV/D8 Edit List is displayed, press M/ m to select the program, then press ENTER. 2 Press M/m to select “Make a Playlist,” from the sub-menu, then press ENTER. The display for entering a Playlist title name appears. To enter a new name, select “Enter,” and follow the explanations on page 34. ,continued Re-editing the “program” in the DV/D8 Edit List 85 3 To use the default name, press </, to select “OK,” then press ENTER. Notes • You cannot set a scene to be shorter than one second. • In order for a One Touch Dub recording to be added to the DV/D8 Edit List, “Add to Edit List” in Features Setup must be set to “On” (page 98). Creating a Copy of the Edited Contents (Copy Dubbing) You can make copies of the programs in the DV/D8 Edit List. Each time you dub a DV/Digital8 format tape, the start and stop points of the selected scenes (called a “program”) are saved in a DV/D8 Edit List. You can select a program from the DV/D8 Edit List and use this information to copy the same contents onto another disc of your choice. To use this function, you will do the following: Connect your digital video camera and prepare for recording Be sure to insert the original DV/Digital8 format tape that corresponds to the program in the DV/D8 Edit List. m Select a program from the DV/D8 Edit List m Dub the selected scenes to a disc The recorder will fast forward and rewind the tape automatically and record the scenes to a disc of your choice. On a DVD-RW (VR mode), chapter marks are inserted at the start of each scene and where the recordings start on the tape. For other discs, the recorder marks chapters either in 6 or 15 minute intervals depending on the setting in “Auto Chapter” in Features Setup (page 97). SYSTEM MENU RETURN </M/m/,, ENTER x REC STOP a Follow steps 1 to 7 of “Preparing for recording using the DV IN jack” (page 75), then press SYSTEM MENU. Be sure to insert the original DV/Digital8 format tape that corresponds to the program in the DV/D8 Edit List. b Press M/m to select “DV/D8 EDIT,” then press ENTER. The DV/D8 Edit menu appears. 86 Creating a Copy of the Edited Contents (Copy Dubbing) c Press M/m to select “DV/D8 Edit List,” then press ENTER. The DV/D8 Edit List menu appears. To change the name of a program 1 While the DV/D8 Edit List is displayed, press M/ m to select the program name you want to change, then press ENTER. 2 Press M/m to select “Rename” from the submenu, then press ENTER. The display for entering the program name appears. 3 Enter a name by following the explanations on page 34. DV/D8 EDIT LIST DV10/11/02 1:30PM - 11/12/02 4:46PM 1H12M 6/ 5 DV12/11/02 1:00PM - 12/11/02 7:05PM 1H16M 6/10 DV12/24/02 11:34AM - 12/25/02 1:24PM 1H24M 6/18 1 Disc mark To erase a program 2 Program name 1 While the DV/D8 Edit List is displayed, press M/ m to select the program you want to erase, then press ENTER. 2 Press M/m to select “Erase” from the sub-menu, then press ENTER. 3 Press </, to select “OK,” then press ENTER. 3 Total playing time 4 Date of editing or recording d Press M/m to select the program you want to record on a disc, then press ENTER. The sub-menu appears. The display for entering a title name appears. Title Name • You can preview the scenes within the program title by selecting “Preview” in step 5. • On a DVD-RW (VR mode), chapter marks are inserted at the start of each scene and where the recordings start on the tape. For other discs, the recorder marks chapters either in 6 or 15 minute intervals depending on the setting in “Auto Chapter” in Features Setup (page 97). Enter the title name. DV10/11/02 1:30PM - 11/12/02 4:46PM OK Enter To enter a new name, select “Enter,” and follow the explanations on page 34. f To use the default name, press </, to select “OK,” then press ENTER. Notes • If you want to play the disc on other DVD equipment, finalize the disc (page 73). • In order for a One Touch Dub recording to be added to the DV/D8 Edit List, “Add to Edit List” in Features Setup must be set to “On” (page 98). • Copy dubbing may not work if you have edited sections that do not contain any recorded material. • This function may not work with certain digital video cameras. In this case, follow the instructions of “Recording From Equipment Connected to the LINE IN Jacks” (page 88). The default title name is fixed, and the display asks whether to start recording. If you want to change the recording mode, press </, to move the cursor then press M/m to select the mode. DV/D8 Dubbing Change the recording mode if necessary. Select "Start" to start dubbing. SP Start Connecting a Digital Video Camera or Other Equipment e Press M/m to select “DV Dubbing,” then press ENTER. z Hints Cancel g Press </, to select “Start,” then press ENTER. The recorder starts recording the tape contents as programmed. To stop during recording, press x REC STOP. h When the recording is finished, press ENTER to select “Close.” The display returns to the DV/D8 Edit menu. i Press RETURN repeatedly to turn off the display. Creating a Copy of the Edited Contents (Copy Dubbing) 87 Recording From Equipment Connected to the LINE IN Jacks Recording from connected equipment Z OPEN/CLOSE You can connect other equipment (e.g. a VCR or video camera), and output the audio/video signals to the recorder for recording. Use the DV IN jack on the front panel if the equipment has a DV output jack (i.LINK jack). See also the instruction manual supplied with the connected equipment. TOOLS M/m, ENTER Connecting other equipment to the LINE 2 IN jacks You can monitor the recorded picture with a TV connected to the recording equipment. X REC PAUSE x REC STOP REC MODE VCR, etc. INPUT SELECT OUTPUT VIDEO S VIDEO AUDIO L R a Turn on your TV and this recorder, then set it to the connected channel (“VIDEO,” etc.). S VIDEO cord (not supplied) Audio/video cord (not supplied) b Press Z OPEN/CLOSE, and place a recordable disc on the tray. c Press Z OPEN/CLOSE to close the disc tray. Wait until “LOAD” disappears from the front panel display. to LINE 2 IN DVD recorder d Press INPUT SELECT to select a input source according to the connection you made. The front panel display changes as follows: Channel number L1 L2 L3 DV : Signal flow z Hint When the connected equipment outputs only monaural sound, use audio cables that distribute monaural sounds to left/right channels (not supplied). Notes • Do not connect the yellow LINE IN (VIDEO) jack when using an S VIDEO cord (not supplied). • Do not connect the output jack of this recorder to another equipment’s input jack with the other equipment’s output jack connected to the input jack of this recorder. Noise (feedback) may result. • Pictures containing copy protection signals that prohibit any copying cannot be recorded. 88 Recording From Equipment Connected to the LINE IN Jacks e Press REC MODE repeatedly to select the recording mode. The recording mode changes as follows: HQ HSP SP LP EP SLP f Select the audio input using the TOOLS menu. A Press TOOLS. B Press M/m to select “Line Audio Input,” then press ENTER. C Press M/m to select the item, then press ENTER. • Stereo (default) • Main/Sub* * When “Main/Sub” is selected, the two different types of sounds are recorded. You can select either sound when playing a disc. Select “Main/Sub” only when using a DVD-RW (VR mode). For other discs, select “Stereo.” Only stereo sound is recorded. g Press X REC PAUSE to set this recorder to record pause. h Insert the source tape into the connected equipment and set to playback pause. Connecting a Digital Video Camera or Other Equipment i At the same, press X REC PAUSE on this recorder and the pause or play button on the connected equipment. Recording starts. j To stop recording, press x REC STOP on this recorder. ◆If you connect a digital video camera with a DV IN jack (without using the DV Edit functions) • Select “DV” in step 4. • Select “Stereo1,” “Mix,” or “Stereo2” from “DV/D8 Audio Input” in step 6. z Hint You can adjust the settings for the recording picture before recording. See “Adjusting the Recording Picture Quality and Size” (page 46). Note When recording a video game image, the screen may not be clear. Recording From Equipment Connected to the LINE IN Jacks 89 About the Setup Display Structure Settings and Adjustments By using the Setup Displays, you can make various adjustments to items such as picture and sound, as well as select a language for the subtitles. System Menu DVD Recorder Dual RW Compatible SYSTEM MENU TITLE LIST The Setup Displays allow you to adjust the recorder to suit your preferences. This section first lists the types of Setup Displays, and then explains how to use the Setup Displays (“Using the Setup Displays”). Plays/erases/edits recorded titles. TIMER TIMER LIST DV/D8 EDIT SETUP m Select “SETUP” Setup Displays 1. “Settings” (page 92) SETUP Settings Tuner Preset Video Set VCR Plus+ Channels Audio Clock Features Language Options Easy Setup SETUP Settings TV Type : 4 : 3 Letter Box Video Pause Mode : Auto Audio Component Black Level : On Features Options Progressive Mode : Auto Line1 Input : Video Line3 Input : Video 2. “Video” (page 94) Easy Setup SETUP Settings Auto Stereo : On Video Tuner Audio : Main Audio Audio ATT : Off Audio DRC : Standard Downmix : Dolby Surround Digital Out : On Features Options Easy Setup Dolby Digital D-PCM DTS : Off SETUP Settings Auto Chapter : Video Parental Control Audio One Touch Dubbing 6 Min 3. “Audio” (page 95) 4. “Features” (page 97) Features Options Easy Setup SETUP • About the Setup Display Structure . . . page 90 • Using the Setup Displays . . . . . . . . . . page 91 • Settings (Basic Settings) . . . . . . . . . . page 92 Settings Format Disc : Selectable Video Dimmer : Bright Audio Auto Display : On Command Mode : DVD3 Features Options 5. “Options” (page 99) Factory Setup Easy Setup • Video Settings . . . . . . . . . . . . . . . . . . page 94 • Audio Settings . . . . . . . . . . . . . . . . . . page 95 • Features Settings . . . . . . . . . . . . . . . . page 97 SETUP Settings • Options Settings . . . . . . . . . . . . . . . . . page 99 Video Audio Features • Easy Setup (Resetting the Recorder) . . . . . . . . . . . . . . . . . . . . . . . . . . page 100 90 About the Setup Display Structure Options Easy Setup Easy Setup 6. “Easy Setup” (page 100) Using the Setup Displays c Press M/m to select “Settings,” “Video,” “Audio,” “Features,” “Options,” or “Easy Setup,” then press ENTER. The selected Setup Display appears. Example: “Video” The Setup Displays are used in the following way. SETUP Settings Note Playback settings stored in the disc take priority over the Setup Display settings, and not all the functions described may work. TV Type : 4 : 3 Letter Box Video Pause Mode : Auto Audio Component Black Level : On Features Options Progressive Mode : Auto Line1 Input : Video Line3 Input : Video Easy Setup d Press M/m to select the item you want to set up, then press ENTER. Available options for the item appear. Example: “TV Type” SETUP SYSTEM MENU 16 : 49 : 3 Letter Box Pause Mode : 4 : 3 Auto Letter Box Audio Component Black Level 4 : 3 OnPan Scan </M/m/,, ENTER RETURN Features Options Progressive Mode : Auto Line1 Input : Video Line3 Input : Video Easy Setup a Press SYSTEM MENU while the recorder is stopped. The System Menu appears. Features - Parental Control Enter your password. DVD Recorder Dual RW Compatible SYSTEM MENU Some items display a dialogue box that provides further detailed settings. Example: The following dialogue box appears when “Parental Control” in Features Setup is selected. Settings and Adjustments TV Type : Video Settings OK TITLE LIST Plays/erases/edits recorded titles. Cancel TIMER TIMER LIST DV/D8 EDIT SETUP In this case, see “Parental Control” in “Features Settings” (page 97). b Press M/m to select “SETUP,” then press ENTER. The Setup Display appears. SETUP Settings Set VCR Plus+ Channels Audio Clock Options Easy Setup ENTER. The set option is displayed next to the setup item. Example: when “16:9” is set. Tuner Preset Video Features e Press M/m to select an option, then press Language SETUP Settings TV Type : 16 : 9 Video Pause Mode : Auto Audio Component Black Level : On Features Options Progressive Mode : Auto Line1 Input : Video Line3 Input : Video Easy Setup To turn off the display Press SYSTEM MENU repeatedly. Using the Setup Displays 91 Settings (Basic Settings) The Settings Setup helps you to make fundamental settings for the recorder. Select “Video” in the Setup Display. To use the display, see “Using the Setup Displays” (page 91). The default settings are underlined. ◆Manual Set Presets or disables channels manually. If some channels could not be set using the Auto Preset or Easy Setup function, you can set them manually. If there is no sound or if the picture is distorted, the tuner system may not have been preset correctly or completely during Auto Preset or Easy Setup. Set the correct tuner system manually by the steps below. 1 Follow steps 1 to 3 of “Using the Setup Displays” (page 91) to select “Settings” in the Setup Display. 2 Press M/m to select “Tuner Preset,” then press ENTER. SETUP Settings Settings - Tuner Preset Ch1 Tuner Preset Video Set VCR Plus+ Channels Antenna / Cable : Audio Clock Auto Preset Language Manual Set : Add AFT : On Features Options Easy Setup 3 Tuner Preset Cable Press M/m to select “Antenna/Cable,” then press ENTER. Settings - Tuner Preset ◆Auto Preset Automatically presets the receivable channels. The recorder can receive VHF channels 2 to 13, UHF channels 14 to 69, and unscrambled CATV channels 1 to 125. First, we recommend that you preset the receivable channels in your area using automatic presetting methods. 1 Follow steps 1 to 3 of “Using the Setup Displays” (page 91) to select “Settings” in the Setup Display. 2 Press M/m to select “Tuner Preset,” then press ENTER. Antenna / Cable : Ch1 Cable Antenna Auto Preset Cable Manual Set : Add AFT : On ◆ To preset cable TV channels Press M/m to select “Cable,” then press ENTER. ◆ To preset VHF and UHF channels Press M/m to select “Antenna,” then press ENTER. 4 Select the channel you want to preset or disable. Channel to be preset/disabled Settings - Tuner Preset Antenna / Cable : Ch1 Cable Settings - Tuner Preset Auto Preset 3 Manual Set : Add AFT : On Antenna / Cable : Auto Preset Press M/m to select “Antenna/Cable,” then press ENTER. Settings - Tuner Preset Antenna / Cable : Ch1 Cable Antenna Auto Preset Cable Manual Set : Add AFT : On ◆ To preset VHF and UHF channels Press M/m to select “Antenna,” then press ENTER. Press M/m to select “Auto Preset,” then press ENTER. All receivable channels are preset in numerical sequence. Settings - Tuner Preset - Auto Preset Searching for receivable channels. Please Wait. 92 Settings (Basic Settings) Manual Set : Add Add AFT : On Erase ◆ To preset a channel A Enter the channel number using the number button(s), then press SET. B Press M/m to select “Manual Set,” then press ENTER. ◆ To preset cable TV channels Press M/m to select “Cable,” then press ENTER. 4 Ch34 Cable Ch 23 C Press M/m to select “Add,” then press ENTER. ◆ To disable a channel A Press CH +/– to select the channel number. B Press M/m to select “Manual Set,” then press ENTER. C Press M/m to select “Erase,” then press ENTER. 5 Press M/m to select “AFT,” then press ENTER. Settings - Tuner Preset Antenna / Cable : Ch1 Cable Auto Preset Manual Set : Add AFT : On On Off 6 Press M/m to select “On,” then press ENTER. On Normally select this. Off Allows you to adjust the pictures manually. Select this if the Auto Fine Tuning function does not work effectively. ◆If the clock does not activate If your clock is set to the wrong time zone or Daylight Saving Time, you can adjust these settings without turning off the Auto Clock Set function. 1 Follow steps 1 to 3 of “Using the Setup Displays” (page 91) to select “Settings” in the Setup Display. 2 3 4 Press M/m to select “Clock,” then press ENTER. 5 Press M/m to select “No,” then press ENTER. Press </, to select “Auto,” then press ENTER. Press M/m to select “Full Auto,” then press ENTER. Settings - Clock - Auto Clock Set ◆ If the picture is not clear Full Auto : No Clock Set CH : –– Time Zone : Auto Daylight Saving : Auto A Press M/m to select “Off,” then press ENTER. The fine tuning bar appears. Fine Tuning Ch34 6 To preset or disable another channel, repeat steps 3 and 6. Set VCR Plus+ Channels Sets up the guide channel number assigned to each channel. You need to set this correctly when you set the timer recording using the VCR Plus+ function. For details, see page 25. Settings - Clock - Auto Clock Set Clock ◆Auto (Auto Clock Set) Turns on the Auto Clock Set function when a channel in your local area broadcasts a time signal. 1 Follow steps 1 to 3 of “Using the Setup Displays” (page 91) to select “Settings” in the Setup Display. 2 Press M/m to select “Clock,” then press ENTER. Select a method for setting the clock. If you select "Auto", this recorder will look for a time signal when you turn it off. 3 Manual Settings - Clock - Auto Clock Set Yes Clock Set CH : –– Time Zone : –– –– Auto Daylight Saving : Auto ◆ Daylight Saving Select “On” or “Off” (standard time), or select “Auto” to have the recorder automatically set the daylight saving time. Press </, to select “Auto,” then press ENTER. Full Auto : No Clock Set CH : ◆ Time Zone Select the time zone of your area, or select “Auto” to have the recorder automatically set your time zone. The options are: Auto y Atlantic y Eastern y Central y Mountain y Pacific y Alaska y Hawaii y Auto Settings - Clock Auto Full Auto : Settings and Adjustments ◆ Clock Set CH Select a channel that carries a time signal using the number buttons. Use this option if you know of a channel that carries a time signal. Most PBS member stations broadcast a time signal. For the fastest response select your local PBS station. Leave the setting at “--” to have the recorder automatically search for a channel that carries a time signal. To return to “- -,” enter “0.” B Press </, to obtain a clearer picture, the press ENTER. 7 Press M/m to select the item you want to set and press ENTER. Then press M/m to make the setting and press ENTER. Time Zone : Daylight Saving : 4 Press M/m to select “Full Auto,” then press ENTER. 5 Press M/m to select “Yes,” then press ENTER. The recorder automatically sets the clock by searching for a channel that carries a time signal and sets your time zone and Daylight Saving Time (if applicable). z Hint If you set “Full Auto” to “Yes,” the Auto Clock Set function is activated whenever the recorder is turned off. ◆Manual (Manual Clock Set) If the Auto Clock Set function did not set the clock correctly for your local area, set the clock manually. 1 Follow steps 1 to 3 of “Using the Setup Displays” (page 91) to select “Settings” in the Setup Display. ,continued Settings (Basic Settings) 93 2 Press M/m to select “Clock,” then press ENTER. Settings - Clock Video Settings Select a method for setting the clock. If you select "Auto", this recorder will look for a time signal when you turn it off. Auto 3 Manual Press </, to select “Manual,” then press ENTER. Settings - Clock - Present Time Choose the settings according to the TV, tuner, or decoder to be connected. Select “Video” in the Setup Display. To use the display, see “Using the Setup Displays” (page 91). The default settings are underlined. Set the time and date manually. Wed 1 / 1 / 2003 SETUP 12 : 00 AM Settings 4 5 Press M/m to set the month, then press ,. Set the day, year, hour, and minutes in sequence. Press </, to select the item to be set, then press M/m to set the numbers. The day of the week is set automatically. Press ENTER to start the clock. z Hint To change the numbers in step 3, press < to return to the item to be changed, and select the numbers by pressing M/m. TV Type : 4 : 3 Letter Box Video Pause Mode : Auto Audio Component Black Level : On Features Options Progressive Mode : Auto Line1 Input : Video Line3 Input : Video Easy Setup TV Type Selects the aspect ratio of the connected TV (4:3 standard or wide). 16:9 Select this when connecting to a widescreen TV or TV with a wide mode function. 4:3 Letter Box Select this when connecting to a 4:3 screen TV. Displays a wide picture with bands on the upper and lower portions of the screen. 4:3 Pan Scan Select this when connecting to a 4:3 screen TV. Automatically displays a wide picture on the entire screen and cuts off the portions that do not fit. Language ◆OSD (On-Screen Display) Switches the display language on the screen. ◆DVD Menu Switches the language for the DVD menu. ◆Audio Switches the language of the sound track. When you select “Original,” the language given priority in the disc is selected. ◆Subtitle Switches the language of the subtitles recorded on the disc. When you select “Audio Follow,” the subtitle language changes according to the language you selected for the sound track. 16:9 z Hint 4:3 Letter Box If you select “Others” in “DVD Menu,” “Subtitle,” or “Audio,” select and enter a language code from “Language Code List” (page 108) using the number buttons. Note 4:3 Pan Scan If you select a language in “DVD Menu,” “Subtitle,” or “Audio” that is not recorded on the DVD VIDEO, one of the recorded languages will be automatically selected. Note Depending on the disc, “4:3 Letter Box” may be selected automatically instead of “4:3 Pan Scan” or vice versa. 94 Video Settings Pause Mode (DVDs only) Selects the picture in pause mode. Auto The picture, including subjects that move dynamically, is output with no jitter. Normally select this position. Frame The picture, including subjects that do not move dynamically, is output in high resolution. Component Black Level Selects the black level (setup level) for the video signals output from the COMPONENT VIDEO OUT jacks (page 51). This setting is not effective when the recorder outputs progressive signal and the PROGRESSIVE indicator lights up on the front panel. On Off Select “Audio” in the Setup Display. To use the display, see “Using the Setup Displays” (page 91). The default settings are underlined. SETUP Sets the black level of the output signal to the standard level. Select this when connecting equipment for which the black level (setup level) is set to “0.” Settings Auto Stereo : On Video Tuner Audio : Main Audio Audio ATT : Off Audio DRC : Standard Downmix : Dolby Surround Digital Out : On Automatically detects if you are playing Film based or Video based software and convert the signal to the appropriate conversion mode. Normally select this. Selects the conversion mode for Video based software, regardless of the software type that you are playing. Options Easy Setup Dolby Digital D-PCM DTS : Off Auto Stereo This function affects only when “Tuner Audio” is set to “Main.” On Receives stereo programs. Normally select this. Off Select this to reduce noise. The sound changes to monaural. Settings and Adjustments Selects the conversion mode of software when the recorder is set to output video signals in progressive format (page 51). Video The Audio Setup allows you to set the sound according to the playback and connection conditions. Features Progressive Mode Auto Audio Settings Tuner Audio Selects the sound to be recorded. Main Records only main sound. SAP Records only the SAP (Second Audio Program) sound. Line1 Input Selects a method of inputting video signals for the LINE IN 1 jack on the rear panel of the recorder. Video Inputs video signals. S Video Inputs S video signals. Line3 Input Selects the method of inputting video signals for the LINE IN 3 jack on the rear panel of the recorder. Video Inputs video signals. S Video Inputs S video signals. Notes • If no SAP sound is received, the main sound is recorded regardless of the setting. • When “Tuner Audio” is set to “SAP,” set “Auto Stereo” to “On.” Audio ATT (attenuation) If the playback sound is distorted, set this item to “On.” The recorder reduces the audio output level. This function affects the output of the following jacks: – LINE OUT (AUDIO L/R) 1/2 jacks On Select this when the playback sound from the speakers is distorted. Off Normally select this position. ,continued Audio Settings 95 Audio DRC (Dynamic Range Control) (DVDs only) Makes the sound clear when the volume is turned down when playing a DVD that conforms to “Audio DRC.” This affects the output from the following jacks: – LINE OUT (AUDIO L/R) 1/2 jacks – DIGITAL OUT (OPTICAL or COAXIAL) jack only when “Dolby Digital” is set to “D-PCM” (page 96). Standard Normally select this position. TV Mode Makes low sounds clear even if you turn the volume down. Wide Range Gives you the feeling of being at a live performance. Downmix (DVDs only) Switches the method for mixing down to two channels when you play a DVD which has rear sound elements (channels) or is recorded in Dolby Digital format. For details on the rear signal components, see “Checking the audio signal format” (page 58). This function affects the output of the following jacks: – LINE OUT (AUDIO L/R) 1/2 jacks – DIGITAL OUT (OPTICAL or COAXIAL) jack when “Dolby Digital” is set to “D-PCM” (page 96). Dolby Surround Normally select this position. Multi-channel audio signals are output to two channels for enjoying surround sounds. Normal Multi-channel audio signals are downmixed to two channels for use with your stereo. Digital Out Selects if audio signals are output via the DIGITAL OUT (OPTICAL or COAXIAL) jacks. On Normally select this position. When you select “On,” see “To set the digital output signal” for further settings. Off The influence of the digital circuit upon the analog circuit is minimal. • To set the digital output signal The following setup items switch the method of outputting audio signals when you connect a component such as an amplifier (receiver) or MD deck with a digital input jack. For connection details, see “Connecting the Audio Cords” (page 19). Select “Dolby Digital” and “DTS” after setting “Digital Out” to “On.” SETUP Settings Auto Stereo : On Video Tuner Audio : Main Audio Audio ATT : Off Audio DRC : Standard Downmix : Dolby Surround Digital Out : On Features Options Easy Setup Dolby Digital D-PCM DTS : Off If you connect a component that does not accept the selected audio signal, a loud noise (or no sound) will come out from the speakers, and may affect your ears or cause speaker damage. 96 Audio Settings ◆Dolby Digital (DVDs only) Selects the type of Dolby Digital signal. D-PCM Select this when the recorder is connected to an audio component lacking a built-in Dolby Digital decoder. You can select whether the signals conform to Dolby Surround (Pro Logic) or not by making adjustments to the “Downmix” item in Audio Setup (page 96). Dolby Digital Select this when the recorder is connected to an audio component with a built-in Dolby Digital decoder. ◆DTS (DVD VIDEO only) Selects whether or not to output DTS signals. On Select this when the recorder is connected to an audio component with a built-in DTS decoder. Off Select this when the recorder is connected to an audio component without a built-in DTS decoder. ◆ When you have already registered a password Features Settings The display for entering the password appears. Features - Parental Control Enter your password. OK The Features Setup provides entries to the following features. Select “Audio” in the Setup Display. To use the display, see “Using the Setup Displays” (page 91). The default settings are underlined. Cancel 3 Enter your four digit password using the number buttons, then select “OK” and press ENTER. SETUP Settings Auto Chapter : Video Parental Control Audio One Touch Dubbing Features - Parental Control 6 Min Features Level : Off Standard : USA Password Options Easy Setup 4 Auto Chapter Automatically divides a recording (a title) into chapters by inserting chapter markings at a specified interval. The markings are made during recording. No chapter mark is inserted. 6Min Inserts chapter marks at approximately 6 minute intervals. 15Min Inserts chapter marks at approximately 15 minute intervals. Features - Parental Control Off Standard : Others USA Password Others 5 Press M/m to select a geographic area as the playback limitation level, then press ENTER. The area is selected. When you select “Others,” press the number buttons to select and enter an area code in the table on page 98. Then select “OK” and press ENTER. 6 Press M/m to select “Level,” then press ENTER. The selection items for “Level” are displayed. Notes • Depending upon the size of the recording being made, the actual interval may vary from the interval selected in “Auto Chapter.” The selected interval should only be used as an approximation to create chapters. • This function is not available when using DVD-RWs in VR mode with the DV Edit function. Chapter marks are automatically entered where the recordings start on the tape (page 78, 79, 81). Level : Settings and Adjustments Off Press M/m to select “Standard,” then press , or ENTER. The selection items for “Standard” are displayed. Features - Parental Control Level : Off Off Standard : Others 8 Password 7 6 Parental Control (DVD VIDEO only) Playback of some DVD VIDEOs can be limited according to a predetermined level, such as the age of the users. Scenes may be blocked or replaced with different scenes. 1 Follow steps 1 to 3 of “Using the Setup Displays” (page 91) to select “Features” in the Setup Display. 2 Press M/m to select “Parental Control,” then press ENTER. ◆ If you have not entered a password The display for registering a new password appears. Features - Parental Control 5 4 7 Select the level you want using M/m, then press ENTER. Parental Control setting is complete. The lower the value, the stricter the limitation. • To cancel the Parental Control setting for the disc Set “Level” to “Off” in step 7. • To change the password A In step 4, select “Password,” then press ENTER. The display for registering a password appears. B Enter a new four-digit password using the number buttons, then select “OK” and press ENTER. Enter a new password. OK Cancel Notes • If you forget your password, you will have to reset it by selecting “Parental Control” under “Factory Setup” in Options Setup (page 99). • When you play discs which do not have the Parental Control function, playback cannot be limited on this recorder. • Depending on the disc, you may be asked to change the Parental Control level while playing the disc. In this case, enter your password, then change the level. If the Resume Play mode is canceled, the level returns to the previous level. ,continued Features Settings 97 • Area code Standard Code number Argentina 2044 Australia 2047 Austria 2046 Belgium 2057 Brazil 2070 Canada 2079 Chile 2090 China 2092 Denmark 2115 Finland 2165 France 2174 Germany 2109 India 2248 Indonesia 2238 Italy 2254 Japan 2276 Korea 2304 Malaysia 2363 Mexico 2362 Netherlands 2376 New Zealand 2390 Norway 2379 Pakistan 2427 Philippines 2424 Portugal 2436 Russia 2489 Singapore 2501 Spain 2149 Sweden 2499 Switzerland 2086 Thailand 2528 United Kingdom 2184 One Touch Dubbing Displays the following items. ◆Finalize Disc Selects whether or not to finalize the disc automatically following One Touch Dub (page 78). 98 Auto Automatically finalizes the disc following One Touch Dub. Manual Allows you to finalize the disc manually. Features Settings ◆Add to Edit List Automatically generates a program in the DV/D8 Edit List during One Touch Dub of DV/Digital8 format tapes. You can use the created program for further editing. For details, see page 78. On Automatically generates a program during One Touch Dub of DV/Digital8 format tapes. Off No program is generated. Options Settings The Options Setup allows you to set up other operational settings. Select “Options” in the Setup Display. To use the display, see “Using the Setup Displays” (page 91). The default settings are underlined. Factory Setup Allows you to select the setup settings by group, and return them to their default settings. Note that all of your previous settings will be lost. 1 Follow steps 1 to 3 of “Using the Setup Displays” (page 91) to select “Options” in the Setup Display. 2 Press M/m to select “Factory Setup,” then press , or ENTER. The display for selecting the group of settings appears. 3 Press M/m to select the group of settings you want to return to default from “Settings,” “Video,” “Audio,” “Features,” “Options” “Parental Control,” and “All,” then press , or ENTER. The dialogue box appears. 4 Press </, to select “Start,” then press ENTER. The selected settings return to the default settings. 5 Press ENTER when “Finish” appears. SETUP Settings Format Disc : Selectable Video Dimmer : Bright Audio Auto Display : On Command Mode : DVD3 Features Options Factory Setup Easy Setup Format Disc (DVD-RW only) Selects the recording format when formatting a DVD-RW. Automatically formats the disc in VR mode. Video Automatically formats the disc in Video mode. Selectable Allows you to select the format before formatting. Settings and Adjustments VR Dimmer Adjusts the lighting of the front panel display. Bright Bright lighting. Dark Low lighting. Display Off Turns off the lighting. Auto Display On Automatically displays information on the screen when the recorder is turned on, etc. Off Displays information only when DISPLAY is pressed. Command Mode Changes the Command Mode of the recorder if other DVD equipment is assigned the same Command Mode. Be sure to match the Command Mode switch on the remote to the setting made here. For details, see “Preparing the Remote” on page 22. DVD1 Select this if the default Command Mode conflicts with other DVD equipment. DVD2 Select this if the default Command Mode conflicts with other DVD equipment. DVD3 The default Command Mode of the recorder. Options Settings 99 Easy Setup (Resetting the Recorder) Select this to restart Easy Setup mode for basic setup. Select “Easy Setup” in the Setup Display. To use the display, see “Using the Setup Displays” (page 91). SETUP Settings Easy Setup Video Audio Features Options Easy Setup Easy Setup 100 1 Follow steps 1 to 3 of “Using the Setup Displays” (page 91) to select “Easy Setup” in the Setup Display. 2 3 4 Press ENTER. Press </, to select “Start,” then press ENTER. Follow the Easy Setup explanation from step 5 on page 22. Easy Setup (Resetting the Recorder) Troubleshooting Additional Information If you experience any of the following difficulties while using the recorder, use this troubleshooting guide to help remedy the problem before requesting repairs. Should any problem persist, consult your nearest Sony dealer. Power The power does not turn on. , Check that the AC power cord is connected securely. Picture There is no picture. Picture noise appears. , The disc is dirty or flawed. , If the picture output signal from your recorder passes through your VCR to get to your TV, or if you are connected to a combination TV/VIDEO player, the copy-protection signal applied to some DVD programs could affect picture quality. If you still experience this problem even when you connect your recorder directly to your TV, try connecting your recorder to your TV’s S VIDEO input. , You have set the recorder to progressive format (the PROGRESSIVE indicator lights up) even though your TV cannot accept the progressive signal. In this case, press the PROGRESSIVE button on the front panel until the progressive indicator turns off. , Even if your TV is compatible with progressive format (480p) signals, the image may be affected when you set the recorder to progressive format. In this case, press the PROGRESSIVE button so that the PROGRESSIVE indicator turns off and the recorder is set to normal (interlace) format. • Troubleshooting. . . . . . . . . . . . . . . . .page 101 • Self-diagnosis Function (When letters/numbers appear in the display) . . . . . . . . . .page 104 • Specifications. . . . . . . . . . . . . . . . . . .page 105 Additional Information , Re-connect the connecting cord securely. , The connecting cords are damaged. , The Setup Display appears. Press RETURN to turn off the display. , Check the connection to your TV (page 16). , Switch the input selector on your TV (such as to “VCR”) so that the signal from the recorder appears on the TV screen. TV program reception does not fill the screen. , Set the channel manually in “Tuner Preset” in Settings Setup (page 92). , Select the correct source using the INPUT SELECT button, or select a channel of any TV program using the CH +/– buttons. • About i.LINK. . . . . . . . . . . . . . . . . . . .page 106 • Glossary. . . . . . . . . . . . . . . . . . . . . . .page 107 • Language Code List . . . . . . . . . . . . . .page 108 ,continued Troubleshooting 101 TV program pictures are distorted. Sound is noisy. , Reorient the TV antenna. , Adjust the picture (see the TV’s instruction manual). , Place the recorder and TV farther apart. , Place the TV and any bunched antenna cables farther apart. , The disc is dirty or flawed. , When playing a CD with DTS sound tracks, noise will come from the LINE OUT (AUDIO L/R) 1/2 jacks (page 50). TV channels cannot be changed. , Switch the input selector to TV. , Connect the antenna cable correctly (page 16). , The sound volume is low on some DVDs. The sound volume may improve if you set “Audio DRC” in Audio Setup to “TV Mode” (page 96). , Set “Audio ATT” in Audio Setup to “Off” (page 95). The picture from equipment connected to the recorder’s input jack does not fill the screen. An alternate audio track cannot be recorded. , If the equipment is connected to the LINE IN 1 jack, select “L1” in the front panel display by pressing CH +/– or INPUT SELECT. If the equipment is connected to the LINE 2 IN jacks, select “L2” in the front panel display by pressing CH +/– or INPUT SELECT. If the equipment is connected to the LINE IN 3 jack, select “L3” in the front panel display by pressing CH +/– or INPUT SELECT. If the equipment is connected to the DV IN jack, (this is usually for a digital video camera connection), select “DV” in the front panel display by pressing CH +/– or INPUT SELECT. The playback picture or TV program from the equipment connected through the recorder is distorted. , If the playback picture output from a DVD player, VCR, or tuner goes through your recorder before reaching your TV, the copy-protection signal applied to some programs could affect picture quality. Disconnect the playback equipment in question and connect it directly to your TV. The picture does not fill the screen, even though the aspect ratio is set in “TV Type” in Video Setup. , The aspect ratio of the disc is fixed on your DVD. Sound There is no sound. , The disc is dirty or flawed. , Re-connect all connections securely. , The connecting cord is damaged. , Check the connections to the amplifier input. , The input source setting on the amplifier is incorrect. , The recorder is in pause mode or in Slow-motion Play mode. , The recorder is in fast forward or fast reverse mode. , If the audio signal does not come through the DIGITAL OUT (OPTICAL or COAXIAL) jacks, check the Audio Setup settings (page 95). Sound distortion occurs. , Set “Audio ATT” in Audio Setup to “On” (page 95). 102 The sound volume is low Troubleshooting , Second Audio Program (SAP) is not available for all programs. A program you are recording does not have a second audio program. , You have set “Tuner Audio” in Audio Settings to “Main” (page 95). Select “SAP” to record alternate audio programs. Playback The disc does not play. , No disc is inserted. , A blank disc is inserted. , The disc is upside down. Insert the disc with the labeled side facing up. , The disc is not correctly inserted. , The recorder cannot play certain discs (such as a CD-ROM) (page 50). , The region code on the DVD VIDEO does not match the recorder (page 49). , Moisture has condensed inside the recorder. Remove the disc and leave the recorder turned on for about half an hour until the moisture evaporates (page 2). , If the disc was recorded on another recorder, the recorder cannot play the disc if it was not finalized (page 73). The disc does not start playback from the beginning. , Resume play was activated (page 53). During stop, select “Reset Resume” in the TOOLS menu, then press ENTER. , You have inserted a disc whose Title menu or DVD menu automatically appears on the TV screen when it is first inserted. The recorder starts playing the disc automatically. , The DVD VIDEO features an auto playback function. Playback stops automatically. , While playing discs with an auto pause signal, the recorder stops playback at the auto pause signal. Some functions such as Stop, Search, or Slowmotion Play cannot be performed. , Depending on the disc, you may not be able to do some of the operations above. See the instruction manual supplied with the disc. The language for the sound track cannot be changed. , Multilingual tracks are not recorded on the DVD VIDEO, DVD-R, DVD+R, DVD+RW, or DVD-RW being played. , The DVD VIDEO prohibits the changing of the language for the sound track. , Try changing the language using the DVD VIDEO’s menu. The subtitle language cannot be changed or turned off. , Multilingual subtitles are not recorded on the DVD VIDEO. , The DVD VIDEO prohibits changing of the subtitles. , Try changing the subtitle using the DVD VIDEO’s menu. The angles cannot be changed. , Multi-angles are not recorded on the DVD VIDEO being played. , You are trying to change the angles when “ANGLE” does not appear on the TV screen (page 59). , The DVD VIDEO prohibits changing angles. , Try changing the angle using the DVD VIDEO’s menu. Recording/Timer recording/Editing Contents previously recorded were erased. , Data that has been recorded on a DVD with a PC will be erased from the disc when the disc is inserted. Recording from the equipment with a timer Nothing was recorded even though you set the Synchro-Rec setting correctly. , You forgot to turn off the connected equipment. Turn off the connected equipment and set the recorder to Synchro-Rec standby mode (page 47). , The recorder was not set to the Synchro-Recording standby mode. Press SYNCHRO REC to have the recorder stand by for recording. Make sure the SYNCHRO REC indicator lights up on the front panel (page 47). , The recorder is connected to the TV output jack of the connected equipment. , Set the TV’s input source to “TV.” Synchro-Recording does not complete. Recording does not start immediately after you press the z REC button. , An unused DVD-RW was inserted. It takes a while for the recorder to automatically format a DVD-RW (VR mode). Nothing was recorded even though you set the timer setting correctly. , There was a power failure during recording. , The recorder’s internal clock stopped due to a power failure that lasted for more than 1 hour. Reset the clock (page 93). , The channel was disabled after the timer recording is set. (See “Manual Set” on page 92.) , Disconnect the AC power cord from the AC outlet, and connect it again. , The program contains copy protection signals that restricts copying. , The timer setting overlapped with another setting that was set later or has priority (page 43). Recording does not stop immediately after you press the x REC STOP button. , It will take a few seconds for the recorder to input disc data before recording can stop. Recording does not stop after you press x STOP. , Press x REC STOP. Timer recording is not complete or did not start from the beginning. , The timer setting for the connected equipment overlapped the recorder’s timer setting (page 47). , There was a power failure during the recording. Additional Information The channel cannot be changed from the channel you are recording. , There was a power failure during recording. If the power recovers during the time a timer recording is set, the recorder resumes recording. Should the power failure continue for more than 1 hour, reset the clock (page 93). , The timer setting overlapped with another setting that was set later or has priority (page 43). , Disc space was not enough. The recorder automatically starts recording when the satellite receiver is turned on. , The Synchro-Rec function was activated. Turn off the satellite receiver and cancel the Synchro-Rec function (page 47). Display The clock has stopped. , Set the clock again (page 93). , The clock stopped due to a power failure that lasted for more than 1 hour. Reset the clock (page 93). The TIMER REC indicator is flashing. , The disc does not have enough space or there are more than 99 titles in the disc. Insert a recordable disc. , There is no recordable disc inside the recorder. The recording mode indication is incorrect. , If you make a recording that is less than three minutes long, the recording mode indication shown during playback may not match the recording mode you selected during recording. Note that the actual recording mode will always match the mode you selected, not the indication during playback. ,continued Troubleshooting 103 Remote commander The remote does not function. , Batteries are weak. , There are obstacles between the remote and the recorder. , The remote is too far from the recorder. , There are no batteries in the remote. , The remote’s manufacturer code returned to the default setting when you replaced the batteries. Reset the code (page 26). , Turn on the recorder. , The remote is not pointed at the remote sensor on the recorder. , Different command modes are set for the recorder and remote. Set the same command mode (page 28). Other Sony equipment responds to the remote. , The same command mode is set for both the equipment and recorder. Set a different command mode for the recorder (page 28). Self-diagnosis Function (When letters/numbers appear in the display) When the self-diagnosis function is activated to prevent the recorder from malfunctioning, a five-character service number (e.g., C 13 50) with a combination of a letter and four numbers appears on the front panel display. In this case, check the following table. First three characters Cause and/or corrective action of the service number C 13 The disc is dirty. , Clean the disc with a soft cloth (page 3). C 31 The disc is not inserted correctly. , Re-insert the disc correctly. E XX (xx is a number) To prevent a malfunction, the recorder has performed the self-diagnosis function. , Contact your nearest Sony dealer or local authorized Sony service facility and give the five-character service number. Example: E 61 10 Others The recorder does not operate properly. , When static electricity, etc., causes the recorder to operate abnormally, unplug the recorder and then plug it in again. Nothing appears in the front panel display. , “Dimmer” in Options Setup is set to “Display Off” (page 99). Five numbers or letters are displayed on the front panel display. , The self-diagnosis function was activated (see the table on page 104). The disc tray does not open when you press the Z OPEN/CLOSE button. , It may take a few seconds for the disc tray to open after you have recorded or edited a disc. This is because the recorder is adding disc data to the disc. The disc tray does not open and “TRAY LOCKED” appears on the front panel display. , Contact your Sony dealer or local authorized Sony service facility. “RECOVERY” appears in the front panel display. , The recorder’s recovery function was activated when the recorder was turned on because the power was turned off or failed during recording. Leave the recorder on until “RECOVERY” disappears from the front panel display. Mechanical sound is heard when the recorder is off. , When the recorder’s clock is being adjusted, operational noises (such as the internal fan) may be heard, even when the power is off. This is not malfunction. 104 Self-diagnosis Function (When letters/numbers appear in the display) Specifications The signals from LINE OUT (AUDIO L/R) jack are measured. When you play PCM sound tracks with a 96 kHz sampling frequency, the output signals from the DIGITAL OUT (OPTICAL or COAXIAL) jack are converted to 48 kHz sampling frequency. Inputs and outputs Laser Semiconductor laser Format NTSC Channel coverage VHF: 2 to 13 UHF: 14 to 69 CATV: A-8 to A-1, A to W, W+1 to W+84 Video reception Frequency synthesizer system Audio reception Split carrier system Antenna 75-ohm antenna terminal for VHF/ UHF Timer Clock: Quartz locked Timer indication: 12-hour cycle (digital) Power back-up duration: 1 hour Video recording format MPEG Video Audio recording format/applicable bit rate Dolby Digital/2 ch, 256 kbps LINE OUT 1/2 (AUDIO) Phono jack Output level: 2 Vrms Load impedance: 10 kilohms (VIDEO) Phono jack Output level: 1.0 Vp-p (S VIDEO) 4-pin mini DIN Output level: Y:1.0 Vp-p, C: 0.286 Vp-p (NTSC) LINE IN 1/2/3 (AUDIO) Phono jack Input level: 2 Vrms Input impedance: more than 22 kilohms (VIDEO) Phono jack Input level: 1.0 Vp-p (S VIDEO) 4-pin mini DIN Input level: Y:1.0 Vp-p, C: 0.286 Vp-p (NTSC) DV IN 4-pin i.LINK S100 DIGITAL OUT (OPTICAL) Optical output jack Output level: –18 dBm (wave length: 660 nm) DIGITAL OUT (COAXIAL) Phono jack Output level: 0.5 Vp-p Load impedance: 75 ohms COMPONENT VIDEO OUT(Y, PB, PR) Phono jack/Y: 1.0 Vp-p/PB, PR: interlace*=0.648 Vp-p, progressive or interlace**=0.7 Vp-p * Component Black Level is On ** Component Black Level is Off CONTROL S IN Mini jack Audio characteristics (Playback) Frequency response DVD (PCM 96 kHz): 4 Hz to 44 kHz (±1.0 dB)/DVD (PCM 48 kHz): 4 Hz to 22 kHz (±0.5 dB)/CD: 4 Hz to 20 kHz (±0.5 dB) Signal-to-noise ratio (S/N ratio) DVD: 115 dB (LINE OUT (AUDIO L/R) 2 jacks only) Harmonic distortion DVD: 0.002 % Dynamic range DVD: 110 dB/CD: 100 dB Wow and flutter DVD: Less than detected value (0.001% W PEAK) Audio characteristics (Recording/ Playback) Frequency response DVD (Dolby Digital 48 kHz): 10 Hz-20 kHz (±1.0 dB) Signal-to-noise ratio DVD: 96 dB Harmonic distortion DVD: 0.004 % Dynamic range DVD: 96 dB Specifications and design are subject to change without notice. Additional Information System Supplied accessories Audio/video cord (1) Power cord (1) Antenna cable (1) Remote commander (remote) (1) Size AA(R6) batteries (2) General Power requirements 120 V AC, 60 Hz Power consumption 43 W Dimensions (approx.) 430 × 89 × 381 mm (17 × 3 5/8 × 15 in.) (width/height/ depth) incl. projecting parts Mass (approx.) 5.6 kg (11.16 lb) Operating temperature 5 ºC to 35 ºC (41 ºF to 95 ºF) Operating humidity 25 % to 80 % Specifications 105 About i.LINK The DV IN jack on this recorder is an i.LINK-compliant DV IN jack. This section describes the i.LINK standard and its features. What is i.LINK? i.LINK is a digital serial interface for handling digital video, digital audio and other data in two directions between equipment having the i.LINK jack, and for controlling other equipment. i.LINK-compatible equipment can be connected by a single i.LINK cable. Possible applications are operations and data transactions with various digital AV equipment. When two or more i.LINK-compatible equipment are connected to this recorder in a daisy chain, operations and data transactions are possible with not only the equipment that this recorder is connected to but also with other devices via the directly connected equipment. Note, however, that the method of operation sometimes varies according to the characteristics and specifications of the equipment to be connected, and that operations and data transactions are sometimes not possible on some connected equipment. Note Normally, only one piece of equipment can be connected to this recorder by the i.LINK cable (DV connecting cable). When connecting this recorder to i.LINK-compatible equipment having two or more i.LINK jacks (DV jacks), see the instruction manual of the equipment to be connected. About the Name “i.LINK” i.LINK is a more familiar term for IEEE 1394 data transport bus proposed by SONY, and is a trademark approved by many corporations. IEEE 1394 is an international standard standardized by the Institute of Electrical and Electronics Engineers. i.LINK Baud rate i.LINK’s maximum baud rate varies according to the equipment. Three maximum baud rates are defined: S100 (approx. 100 Mbps*) S200 (approx. 200 Mbps) S400 (approx. 400 Mbps) The baud rate is listed under “Specifications” in the instruction manual of each equipment. It is also indicated near the i.LINK jack on some equipment. The maximum baud rate of equipment on which it is not indicated such as this unit is “S100.” When units are connected to equipment having a different maximum baud rate, the baud rate sometimes differs from the indicated baud rate. * What is Mbps? Mbps stands for megabits per second, or the amount of data that can be sent or received in one second. For example, a baud rate of 100 Mbps means that 100 megabits of data can be sent in one second. 106 About i.LINK i.LINK functions on this recorder For details on how to dub when this recorder is connected to other video equipment having DV jacks, see page 75. The DV jack on this recorder can only input DVC-SD signals. It cannot output signals. The DV jack will not accept MICRO MV signals from equipment such as a MICRO MV digital video camera with an i.LINK jack. For further precautions, see the notes on page 75. For details on precautions when connecting this recorder, also see the instruction manuals for the equipment to be connected. Required i.LINK Cable Use the Sony i.LINK 4-pin-to-4-pin cable (during DV dubbing). i.LINK and are trademarks. CPRM (Content Protection for Recordable Media) is a coding technology that protects copyrights for images. sided DVD is 8.5 GB, a single-layer and double-sided DVD is 9.4 GB, and double-layer and double-sided DVD is 17GB. The picture data uses the MPEG 2 format, one of the worldwide standards of digital compression technology. The picture data is compressed to about 1/40 (average) of its original size. The DVD also uses a variable rate coding technology that changes the data to be allocated according to the status of the picture. Audio information is recorded in a multi-channel format, such as Dolby Digital, allowing you to enjoy a more real audio presence. Furthermore, various advanced functions such as the multi-angle, multilingual, and Parental Control functions are provided with the DVD. Dolby Digital (page 96) DVD-R (page 35) Digital audio compression technology developed by Dolby Laboratories. This technology conforms to multi-channel surround sound. The rear channel is stereo and there is a discrete subwoofer channel in this format. Dolby Digital provides the same discrete channels of high quality digital audio found in “Dolby Digital” theater surround sound systems. Good channel separation is realized because all of the channel data is recorded discretely and little deterioration occurs because all channel data processing is digital. A DVD-R is a recordable disc that is the same size as a DVD VIDEO. Contents can be recorded only once to a DVD-R, and will have the same format as a DVD VIDEO. Glossary Chapter (page 55) Sections of a picture or a music feature that are smaller than titles. A title is composed of several chapters. Depending on the disc, no chapters may be recorded. CPRM (page 35) Title (page 55) The longest section of a picture or music feature on a DVD, movie, etc., in video software, or the entire album in audio software. Track (page 55) Sections of a music feature on a CD (the length of a song). DVD-RW (page 35) A DVD-RW is a recordable and rewritable disc that is the same size as a DVD VIDEO. The DVD-RW has two different modes: VR mode and Video mode. DVDs created in Video mode have the same format as a DVD VIDEO, while discs created in VR (Video Recording) mode allow the contents to be programmed or edited. Audio signal processing technology that Dolby Laboratories developed for surround sound. When the input signal contains a surround component, the Pro Logic process outputs the front, center and rear signals. The rear channel is monaural. DVD+RW (page 35) DTS (page 96) DVDs can be classified as Film based or Video based software. Film based DVDs contain the same images (24 frames per second) that are shown at movie theaters. Video based DVDs, such as television dramas or sit-coms, display images at 30 frames (or 60 fields) per second. Digital audio compression technology that Digital Theater Systems, Inc. developed. This technology conforms to multi-channel surround sound. The rear channel is stereo and there is a discrete subwoofer channel in this format. DTS provides the same discrete channels of high quality digital audio. Good channel separation is realized because all of the channel data is recorded discretely and little deterioration occurs because all channel data processing is digital. Compared to the Interlace format that alternately shows every other line of an image (field) to create one frame, the Progressive format shows the entire image at once as a single frame. This means that while the Interlace format can show 30 frames/60 fields in one second, the Progressive format can show 60 frames in one second. The overall picture quality increases and still images, text, and horizontal lines appear sharper. Additional Information Dolby Surround (Pro Logic) (page 96) Progressive format (page 51) A DVD+RW (plus RW) is a recordable and rewritable disc. DVD+RWs use a recording format that is comparable to the DVD VIDEO format. Film based software, Video based software (page 51) Index (page 57) A number that divides a track into sections to easily locate the point you want on a CD. Depending on the disc, no index may be recorded. Interlace format (page 51) DVD VIDEO (page 49) A disc that contains up to eight hours of moving pictures even though its diameter is the same as a CD. The data capacity of a single-layer and single-sided DVD is 4.7 GB (Giga Byte), which is 7 times that of a CD. The data capacity of a double-layer and single- Interlace format shows every other line of an image as a single “field” and is the standard method for displaying images on television. The even number field shows the even numbered lines of an image, and the odd numbered field shows the odd numbered lines of an image. Glossary 107 Language Code List For details, see pages 57, 60, 94. The language spellings conform to the ISO 639: 1988 (E/F) standard. Code 1027 Afar 1028 Abkhazian 1032 Afrikaans 1039 Amharic 1044 Arabic 1045 Assamese 1051 Aymara 1052 Azerbaijani 1053 Bashkir 1057 Byelorussian 1059 Bulgarian 1060 Bihari 1061 Bislama 1066 Bengali; Bangla 1067 Tibetan 1070 Breton 1079 Catalan 1093 Corsican 1097 Czech 1103 Welsh 1105 Danish 1109 German 1130 Bhutani 1142 Greek 1144 English 1145 Esperanto 1149 Spanish 1150 Estonian 1151 Basque 1157 Persian 1165 Finnish 1166 Fiji 1171 Faroese 1174 French 1181 Frisian 1183 Irish 1186 Scots Gaelic 1194 Galician 1196 Guarani 1203 Gujarati 1209 Hausa 1217 Hindi 1226 Croatian 1229 Hungarian 1233 108 Language Armenian Language Code List Code Language Code Language 1235 Interlingua 1502 Serbo-Croatian 1239 Interlingue 1503 Singhalese 1245 Inupiak 1505 Slovak 1248 Indonesian 1506 Slovenian 1253 Icelandic 1507 Samoan 1254 Italian 1508 Shona 1257 Hebrew 1509 Somali 1261 Japanese 1511 Albanian 1269 Yiddish 1512 Serbian 1283 Javanese 1513 Siswati 1287 Georgian 1514 Sesotho 1297 Kazakh 1515 Sundanese 1298 Greenlandic 1516 Swedish 1299 Cambodian 1517 Swahili 1300 Kannada 1521 Tamil 1301 Korean 1525 Telugu 1305 Kashmiri 1527 Tajik 1307 Kurdish 1528 Thai 1311 Kirghiz 1529 Tigrinya 1313 Latin 1531 Turkmen 1326 Lingala 1532 Tagalog 1327 Laothian 1534 Setswana 1332 Lithuanian 1535 Tonga 1334 Latvian; Lettish 1538 Turkish 1345 Malagasy 1539 Tsonga 1347 Maori 1540 Tatar 1349 Macedonian 1543 Twi 1350 Malayalam 1557 Ukrainian 1352 Mongolian 1564 Urdu 1353 Moldavian 1572 Uzbek 1356 Marathi 1581 Vietnamese 1357 Malay 1587 Volapük 1358 Maltese 1613 Wolof 1363 Burmese 1632 Xhosa 1365 Nauru 1665 Yoruba 1369 Nepali 1684 Chinese 1376 Dutch 1697 Zulu 1703 Not specified 1379 Norwegian 1393 Occitan 1403 (Afan)Oromo 1408 Oriya 1417 Punjabi 1428 Polish 1435 Pashto; Pushto 1436 Portuguese 1463 Quechua 1481 Rhaeto-Romance 1482 Kirundi 1483 Romanian 1489 Russian 1491 Kinyarwanda 1495 Sanskrit 1498 Sindhi 1501 Sangho Index Words in quotations appear in the onscreen displays. Numerics 16:9 23, 94 4:3 Letter Box 23, 94 4:3 Pan Scan 23, 94 A B Batteries 22 C “Cable” 92 CD 49 Chapter 40, 107 Chapter mark 67 “Clock” 93 “Combine Titles” 71 “Command Mode” 28, 99 “Component Black Level” 95 Connecting the antenna cable 16 the audio cords 19 the video cords 18 Copy Control Signals 36 Copy Dubbing 86 Copy-Free 36 Copy-Never 36 Copy-Once 36 CPRM 35 “Create Playlist” 68 D “Digital Out” 96 Digital video camera 75 “Dimmer” 99 Disc Info. 37 Disc Map 38 “Disc Name” 72 Disc space 37 E “Easy Setup” 100 Easy Setup 22 Editing 62 DV Edit 75 Playlist Edit 67 “Erase” 65 “Erase All” 73 “Erase Titles” 65 “Extend Rec. Time” 42 F “Factory Setup” 99 Film based software 51, 107 “Finalize Disc” 98 Finalizing 73 “Format Disc” 99 Formatting 74 Front panel display 14, 57 H Handling discs 3 I Index 107 INSTANT REPLAY 52 INSTANT SEARCH 52 INTERLACE 51 Interlace format 51, 107 J Jog Stick 52 L “Language” 94 “Line1 Input” 95 “Line3 Input” 95 M Menu DVD’s menu 51 Top menu 51 “Move Title” 70 O One Touch Dub 78, 98 On-screen display Setup Display 91 Sub-menu 33 System Menu 31 TOOLS menu 32 Original 32, 63 “OSD” language 94, 23 P Page mode 32 Parental Control 51, 97 “Pause Mode” 95 PCM 57 Playback 49 fast forward/fast reverse 52 Freeze Frame 52 playable discs 49 Replay 52 Resume Play 53 selecting a recorded title 53 Slow-motion play 52 Playlist 32, 63 Pro Logic 21, 107 Program Edit 79 PROGRESSIVE 51 Progressive format 51, 107 “Progressive Mode” 95 Protection disc 72 title 64 Additional Information “A-B Erase” 66 “Add to Edit List” 98 Adjusting playback picture/sound 60 recording picture 46 Advanced Program Edit 81 AFT 93 Angle 59 Area code 98 “Audio” 94 Audio 57 “Audio ATT” 95 “Audio DRC” 96 “Audio Filter” 61 “Auto Chapter” 97 “Auto Clock Set” 23, 93 “Auto Display” 99 “Auto Stereo” 95 Display front panel display 14, 57 On-screen display 31 Setup Display 91 “Divide Title” 70 Dolby Digital 21, 24, 57, 96, 107 “Downmix” 96 DTS 24, 57, 96, 107 Dubbing 75 Copy Dubbing 86 One Touch Dub 78, 98 Program Edit 79 DV/D8 Edit List Create a Playlist 85 Erase 87 Preview 85 Re-edit 84 Rename 87 “DVD Menu” 94 DVD VIDEO 49, 107 DVD+RW 35, 107 DVD-R 35, 107 DVD-RW 35, 107 Q Quick Guide to DVD Disc Types back cover Quick Timer 39 R Rec Mode Adjust 41 Recording 35 picture adjustment 46 recordable discs 35 recording format 36 recording mode 36 while watching another programme 39 RECOVERY 104 Region code 49 Remote 22, 26 Resume Play 53 “Play From Start” 53 “Reset Resume” 53 S SAP (Second Audio Program) 39 Scene List 69, 77 Searching fast forward/fast reverse 52 locating the beginning of the title/ chapter/track 52 Setting the VCR Plus+ channels 25, 93 Setup Display 91 Sort 54 Stereo programs 39 Sub-menu 33 Subtitle 60, 94 Surround 58 Synchro Rec 47 System Menu 31, 91 ,continued Index 109 T Timer List 42 Timer recording check/change/cancel 42 manual setting 40 Rec Mode Adjust 41 Synchro Rec 47 VCR Plus+ system 44 Title 107 Title List 32, 53, 67 Sort 54 Thumbnail 54 Zoom 54 “Title Name” 64 TOOLS menu 32 Track 107 Troubleshooting 101 “Tuner Audio” 95 “Tuner Preset” 23, 92 “TV Type” 23, 94 TV Virtual Surround (TVS) 58 Dynamic 58 Night 59 Standard 59 Wide 58 V VCR Plus+ 44 Video based software 51, 107 Video mode 62 VR (Video Recording) mode 36, 63 Z Zoom 54 110 Index Quick Guide to DVD Disc Types : Most suitable. : Can be used. : Some functions are limited. : Cannot be used. Refer to the following when selecting a disc (DVD-RW, DVD+RW, or DVD-R) and a recording format (VR mode or Video mode for DVD-RW discs). Each disc can record for up to six hours. You want to... Record TV programs Reuse by deleting unwanted contents Edit recorded contents Edit/Record from connected equipment Copy discs for distribution *1 Play on other DVD equipment *1 Features Recording Rewritable? Yes Yes Yes No Can create chapters at fixed intervals (auto.) Yes Yes Yes Yes Can create chapters wherever you like (manual) Yes No No No Can record 16:9 size pictures Yes Yes *2 No Yes *2 Can record Copy-Once programs Yes No No No Can perform basic edit functions Yes Yes Yes Yes *3 Can perform advanced edit functions (Playlist edit) Yes No No No One Touch Dub Yes Yes Yes Yes Program Edit Yes Yes Yes Yes Advanced Program Edit Yes Yes *4 Yes *4 Yes *4 Auto Scene Chaptering Yes No No No Yes No Yes Yes Editing DV editing Compatibility with other DVD equipment Finalization required? No Can generate a Title Menu (DVD Menu) No *1 DVD-RWs (VR mode) can only be played on DVD equipment that is VR compatible. *2 Only if the recording mode is SP, HSP, or HQ, and “Rec Screen Size” is set to 16:9. *3 Erasing titles does not free up disc space. *4 You will need another blank DVD-RW. *5 For certain DVD equipment, finalization may be required. Printed on 100% recycled paper using VOC (Volatile Organic Compound)free vegetable oil based ink. Sony Corporation Printed in Malaysia *5 *5 Yes Yes Note For details of the above functions and implied restrictions, see the explanations inside the manual.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project