AeroLift 35 - AV-iQ
AeroLift 35
Installation & Operating Instructions
Caution:
1 Read instructions completely before proceeding. Follow instructions carefully.
Installation contrary to instructions invalidates warranty.
2 Do not obstruct operation of AeroLift 35 with fingers or any other
object. Serious injury or damage could result.
3 It is not uncommon to overheat the motor during initial installation when
setting limits. The motor is thermally protected and will stop working
temporarily. DO NOT physically pull the unit down when this occurs. Once it
has cooled to a safe temperature, it will begin operating again.
4 The AeroLift 35 is designed to accommodate ceiling suspended
equipment. Equipment should not be allowed to rest on ceiling closures
during operation (see “Installing Projector”).
5 Entire bottom of unit must be unobstructed to permit proper operation.
6 Unit must be installed level (use a carpenter’s level).
7 Unit operates on 110-120V AC 60 Hz. current.
AeroLift 35
(with Closure panel)
Note: Unit has been thoroughly inspected and tested at factory and found to be
operating properly prior to shipment.
Planning
Electrical Connections
1 Based on screen location and projector specifications, determine proper
position for projector installation.
2 Confirm that there is adequate space for installation and operation. Minimum
clearance above ceiling level varies according to height of projector, projector
mounting bracket, optional ceiling closure and optional Environmental Air
Space Housing.
3 Arrange to provide service access to the unit.
4 Total maximum capacity for the AeroLift 35 is 35 lbs.
(including closure, projector and bracket).
Unit operates on 110-120V, 60 Hz. AC current. The AeroLift 35 is shipped closed,
with a temporary field connection provided in the form of a pigtail temporarily
wired to the unit. After hanging the unit, make sure power is off and use this
pigtail to temporarily connect the unit to power and to a switch, so the unit can be
lowered to allow access inside.
Please note: Make sure electrical supply has been disconnected before
attempting to connect AeroLift to electricity.
Terminal strip for field connections is located inside a junction box on the end
of the unit. Unit is shipped with internal wiring complete to the terminal strip.
Once the unit has been lowered, turn off power and remove the J-box cover.
The terminal strip is attached to the cover. Disconnect temporary pigtail from
unit, then complete permanent wiring to electricity and to switches. Wire to
connect unit to power supply and to switches should be furnished by installer.
Connections should be made in accordance with wiring diagram, and wiring
should comply with national and local electrical codes. All operating switches
should be “off” before power is connected. AeroLift should be operated and
checked prior to installing projector and/or optional ceiling closure.
As Soon As AeroLift Arrives
1 Open carton and inspect for damage.
2 Locate the following parts:
A. The unit itself
B. Controls
C. Any optional equipment
3 Test lift prior to installation.
Hanging Unit
AeroLift 35
The AeroLift is provided with four (4) mounting angles for suspending or direct
mounting the unit from above, or direct mounting from the sides. These angles
provide up to 1½" of adjustment (side to side). The unit should be guy wired or
blocked to prevent swinging. All installations should observe the following guidelines:
1 Installer must ensure that all fasteners and supports are of
adequate strength to securely support AeroLift 35 and
projector. It is recommended that hardware structure be able to
hold at least four times the combined weight of the lift, projector,
housing, closure and ceiling material attached to closure.
Caution: DO NOT hang from, "ride" or pull down on the unit.
This could create a failure and cause damage and/or injury.
Front View
187/8"
12½"
413/16"
3/4"
Printed in U.S.A.
12½"
20"
Top
Mounting
Hole
Top View
221/4"
2 Fastening methods must be suitable for mounting surface,
and securely anchored so vibration or abusive pulling on unit
will not weaken installation.
3 Bottom of unit must be unobstructed after installation.
Sufficient clearance must be allowed below projector or optional ceiling closure.
4 Do not use unit to support adjacent ceiling, light fixtures, etc.
5 Do not complete the ceiling below the unit until electrical connections have been
completed and unit has been operated successfully.
6 Use slots on the projector plate and on the closure to adjust the unit to ensure
proper alignment of ceiling closure relative to ceiling opening.
Form AeroLift35_Inst16
Side View
11/4"
Side
Mounting
Slots
Copyright © 2016 Draper Inc.
(Relevant Mounting Dimensions)
Anti-Slip
Hole
Figure (1)
121/2"
101/8"
193/8"
If you encounter any difficulties installing or servicing your AeroLift 35, call your
dealer or Draper, Inc. in Spiceland, Indiana, 765-987-7999 or fax 765-987-7142.
page 2 of 4
AeroLift 35 by Draper, Inc.
Operation
Limit Switch Adjustments
When unit is first operated, be cautious! If unit fails to operate when the switch
is flipped “down”, return switch to “off” and re-check electrical connections
before proceeding. Cycle unit down and up several times to confirm satisfactory
operation.
CAUTION: Be sure all switches are in “off” position before adjusting limit switches
Always be prepared to shut lift off manually when new adjustment is being tested.
110-120V Single Station Control
3-position up-off-down switch permits operation to be stopped at any point. Factory
adjusted limit switches automatically stop AeroLift when fully down or fully up.
Limit switches for the AeroLift 35 are preset at the factory. The “Up” (closed) limit switch
is set for fully closed. The “down” (show) limit switch is set for fully lowered. Once unit is
in place, the “down” limit switch may need to be changed to stop the AeroLift 35 closer
to the ceiling (that is, to raise the “down” position). Limit switches are located on the end
of roller, and are accessible by removing the cover of the junction box at the left end of
the unit. To adjust the limit switches, use a 5/32" screwdriver/allen wrench.
Optional 110-120V Multiple Station Control
Switches are similar in appearance to 110-120V Single Station Control. AeroLift
stops when switch is released and may be restarted in either direction. Factory
adjusted limit switches automatically stop AeroLift when up or fully down.
Caution: It is not uncommon to overheat the motor during initial installation
when setting limits. The motor is thermally protected and will stop working until it
has cooled to a safe temperature before it will start operating again. DO NOT
physically pull the unit down when this occurs.
Optional 24V Control
Three-button up-stop-down switches stop at any point desired, operate in any
sequence. Factory adjusted limit switches automatically stop AeroLift when fully up
or fully down.
“Down” position may be adjusted by turning the #1 limit switch adjustment socket. Turning
the socket clockwise will stop the AeroLift 35 closer to the ceiling. Turning it counterclockwise will cause the lift to stop at a lower point.
Optional Infrared or Radio Frequency Remote Control
If ordered, a three-button transmitter is provided, with “up”, “down” and “stop”
buttons. Unit starts up or down when appropriate button is pressed, and may be
stopped by pressing “off” button. Factory set limit switches stop unit automatically
when projector is in “show” position. Multiple Station Control required for this
option.
Optional RS232/Ethernet
Serial communication and network communication optionally available with wall
switches, RF or IR remote.
Optional Key Operated Switching
Two kinds of key-operated switches are optionally available with this unit.
1 The key-operated power supply switch controls power to the AeroLift 35 and
switches. When it is “off”, the switches will not operate lift. Key may be removed
from the switch in either “on” or “off” position.
2 A three-position key switch permits the AeroLift 35 to be operated directly by key.
In this case, the screen’s operator must always have a key.
Adjusting “Down” (SHOW position)
Adjusting “Up” (CLOSED position)
Because the “up” (“closed”) position is preset at the factory, Draper does not recommend
changing this position using the limit switch. The “up” position of the closure may be
changed by changing the length of threaded rod (see fig. 6). If necessary, however,
“up” position may be adjusted by turning the #2 limit switch adjustment socket. Turning
the socket counterclockwise creates a higher, or more fully closed position. Turning it
clockwise creates a lower ‘UP” (closed) position.
UP LIMIT
Figure (2)
DOWN LIMIT
JUNCTION BOX
Fabric Roller Adjustment Setscrew
Testing the Safety Limit Switches
The AeroLift 35 are equipped with two Safety Limit Switches (see "AeroLift—
Limit Switch Adjustment (Bottom View)" diagram on page 3). These switches
may be damaged during shipping or by rough handling on the job site.
Once the AeroLift has been installed in the ceiling, but
before the projector and closure are attached, the Safety
Limits must be tested.
Use a screwdriver or other tool to press and hold the limit switch. While holding down the limit switch, have someone operate the unit. If the unit runs up
while the limit switch is depressed, the limit switch is broken and must be
replaced. Operating the unit without a functioning Safety Limit Switch could cause
the unit's motor to continue operating after the lift is closed, leading to a failure and
the possibility of damage or injury. Make sure to test BOTH switches.
Please Note: As weight is applied to the AeroLift, the projector plate may
shift slightly. If this occurs, use setscrews on bottom of fabric roller brackets
to compensate for shift and level projector plate (see page 3).
Caution: Make sure limit switch is set so that the AeroLift 35 motor is NOT still
running after the lift is closed. If it continues to cycle once the lift is closed, a
failure may occur, making the unit descend rapidly and causing damage and/or
injury.
Please Note: If load is off-center of pan, you may need to adjust the pitch of the
fabric rollers. One setscrew is provided on each end of both fabric rollers (see
above drawing). Use these to adjust roller pitch to keep entire fabric panel taut, so
load is evenly distributed. Use 1/8" hex key to adjust.
page 3 of 4
AeroLift 35 by Draper, Inc.
Installing Projector Using Universal Projector Mount
(Maximum Capacity 11.8 kg)
If you ordered the unit with optional Universal Projector Mount pre-installed,
disregard these instructions.
If you did not order the mount pre-installed, you will need to install a new
Projector Pan, which includes the Universal Projector Mount's rectangular plate.
See Installation Instructions included with Universal Pojector Mount.
Figure (3)
5½"
7"
(140mm)
Attaching Universal Projector Mount to Projector Pan
(178mm)
1 Lower unit until the Bottom Pan is resting on a tabletop or other stable and
sturdy surface.
2 Remove Lifting Cable Bar from Bottom Pan (see Fig. 4).
3 Remove bolts holding Projector Pan to Bottom Pan (see Fig. 6).4
4 Remove Projector Pan and set aside.
5 Place new Projector Pan with Universal Mount into place.
6 Re-attach Projector Pan to Bottom Pan.
7 Re-attach Lifting Cable Bar to Bottom Pan.
Figure (4)
5mm)
10" (254mm)
7"
12" (305mm)
(178mm)
2½"
15
5½" 3 /16" (100mm)
(64mm)
7"
(140mm)
12" (305mm)
(178mm)
10" (254mm)
21/16"
(52mm)
12"
(304mm)
12" (305mm)
AeroLift Clearance
Installing Optional Environmental Air Space Housing
The Environmental Air Space Housing is shipped in pieces, and must be
assembled by the installer. The height of the Environmental Air Space Housing is set by drilling out the knockouts at the desired locations then using
screws to connect side panels. It is recommended that an access panel be
installed in the ceiling to allow future access. The optional environmental air
space housing must be installed to isolate the lift from the “other space used
for environmental air.” Includes trim ring for ceiling opening.
See installation instructions included with Environmental Air Space Housing.
Figure (5)
Caution: Make
sure there are
no obstructions
to the AeroLift's
operation
Installing Optional Ceiling Closure
If your AeroLift is equipped with optional ceiling closure, it can be used as
is, or in conjunction with a square of existing ceiling tile.
See installation instructions included with ceiling closure.
/8" Min. clearance
1
Installing Optional Ceiling Trim Kit
The AeroLift is available with a ceiling trim kit, which consists of the lower
section of the Environmental Air Space Housing and the optional closure
panel. See installation instructions included with Ceiling Trim Kit.
www.draperinc.com
(765) 987-7999
page 4 of 4
AeroLift 35 by Draper, Inc.
Wiring Diagrams
Single Station Control
Optional Multiple Station Control
RD 14 AWG
LS2
PROJECTOR
OUTLET
BL
14 AWG
PROJECTOR
OUTLET
BK 14 AWG
BK 14 AWG
BK
WH
BL
WH 14 AWG
RD
OR
LS2
OR
LS1
LS1
RD
BK
MOTOR
WH 14 AWG
BK
BK
RD
GN14 AWG
GN14 AWG
BK
WH
BL
LS2
LS1
BL
14 AWG
BK 14 AWG
BK 14 AWG
RD
RD 14 AWG
LS2
LS1
BK
MOTOR
GN
WH
GN
GN/YL 14 AWG
WH
BL
BK
RD RD BK BK WH
Dashed Wiring
By electrician.
BK
GN/YL 14 AWG
BL
Dashed Wiring
By electrician.
WH
1 2 3 4 5
6
7
8
TB
UP
RD
RD RD BK BK WH
1 2 3 4 5
WH
6
7
8
N
GRD
TB
DOWN
BL
COM
BK
UP
DOWN
UP
RD
COMMON
SWITCH
N
L1
To 110-120 Vac Line
BL
COM
GRD
L1
DOWN
BK
To 110-120 Vac Line
UP
RD
Location of key
operated On-off
switch if furnished.
DOWN
BL
COM
BK
Lift Low Voltage (& Wireless) Control
Lift LVC — AeroLift Wiring Diagram
AeroLift Terminal Block
Dashed Wiring
By electrician.
Low voltage
wiring by others.
Brown-to lift (UP)
Red-to lift (DOWN)
White-Neutral (Common) to lift & 110-120V AC
Green-Ground
k to 110
120V AC
Black-to
110-120V
w-to 110-120V AC
Yellow-to
1
2
3
4 5
UP DN COM
6 7
N N
Key Operated
On-Off switch
(if furnished).
Eye Port for IR Eye
or RF Receiver.
Splitter is required if both
are used with one Lift LVC.
L1 N
3 Button Wall Switch
Aux Port for connecting
additional Lift LVC modules
(up to six total-connect from Aux to Eye).
(765) 987-7999
GND
To 110 -120V
AC Line
DOWN - Black
COM - White
UP - Red
www.draperinc.com
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising