TP-Link Archer T4U User Guide

Add to my manuals
54 Pages

advertisement

TP-Link Archer T4U User Guide | Manualzz

Archer T4U

AC1200 Wireless Dual Band USB Adapter

Rev: 1.1.0

1910011106

COPYRIGHT & TRADEMARKS

Specifications are subject to change without notice. is a registered trademark of

TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from

TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD.

All rights reserved. http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment has been SAR-evaluated for use in hand.

SAR measurements are based on a 5mm spacing from the body and that compliance is achieved at that distance.

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

National Restrictions

This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

Country Restriction Reason/remark

Bulgaria None

General authorization required for outdoor use and public service

France

Italy

Luxembourg

Norway

Outdoor use limited to the band 2454-2483.5

MHz

Military Radiolocation use. Refarming of the 2.4 GHz

10 mW e.i.r.p. within band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012

None

None

If used outside of own premises, general authorization is required

General authorization required for network and service supply(not for spectrum)

Implemented

Russian Federation None

This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund

Only for indoor applications

Note: Please don’t use the product outdoors in France.

Canadian Compliance Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and

(2)This device must accept any interference, including interference that may cause undesired operation of the device.

Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes:

(1) cet appareil ne doit pas provoquer d’interférences et

(2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil.

Industry Canada Statement

Complies with the Canadian ICES-003 Class B specifications.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations.

Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

Korea Warning Statements

당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice & BSMI Notice

注意!

依據 低功率電波輻射性電機管理辦法

第十二條 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻

率、加大功率或變更原設計之特性或功能。

第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行;經發現有干擾現象時,應立

即停用,並改善至無干擾時方得繼續使用。前項合法通信,指依電信規定作業之無線電信。低功

率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。

減少電磁波影響,請妥適使用。

5.25GHz 5.35GHz 區域內操作之無線設備的警告聲明

工作頻率 5.250~5.350GHz 該頻段限於室內使用。

安全諮詢及注意事項

●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

●注意防潮,請勿將水或其他液體潑灑到本產品上。 

●插槽與開口供通風使用,以確保本產品的操作可靠並防止過熱,請勿堵塞或覆蓋開口。

●請勿將本產品置放於靠近熱源的地方。除非有正常的通風,否則不可放在密閉位置中。

●請不要私自打開機殼,不要嘗試自行維修本產品,請由授權的專業人士進行此項工作。

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами

України.

Safety Information

 When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source.

 Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.

 Avoid water and wet locations.

 This product can be used in the following countries:

AT

ES

LT

RU

BG

FI

LV

SE

BY

FR

MT

SK

CA

GB

NL

TR

CZ

GR

NO

UA

DE

HU

PL

US

DK

IE

PT

EE

IT

RO

TP-LINK TECHNOLOGIES CO., LTD

DECLARATION OF CONFORMITY

For the following equipment:

Product Description: AC1200 Wireless Dual Band USB Adapter

Model No.: T4U

Trademark: TP-LINK

We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:

Directives 1999/5/EC, Directives 2006/95/EC, Directives 1999/519/EC, Directives 2011/65/EU

The above product is in conformity with the following standards or other normative documents:

EN 300 328 V1.8.1

EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1

EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011

EN 50566: 2013

EN 301 893 V1.7.1

The product carries the CE Mark:

Person responsible for marking this declaration:

Yang Hongliang

Product Manager of International Business

Date of issue: 2014

TP-LINK TECHNOLOGIES CO., LTD.

Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,

Shennan Rd, Nanshan, Shenzhen, China

CONTENTS

Package Contents .................................................................................................... 1

Chapter 1 Product Overview ................................................................................. 2

1.1 Introduction ................................................................................................................ 2

1.2 Features ..................................................................................................................... 2

1.3 Hardware Overview ................................................................................................... 3

Chapter 2 Installation ............................................................................................. 4

2.1 Hardware Installation ................................................................................................. 4

2.2 Software Installation .................................................................................................. 5

Chapter 3 Connect to a Wireless Network ......................................................... 10

3.1 To connect using TWCU ......................................................................................... 10

3.2 To connect using WPS ............................................................................................ 14

3.2.1 PBC (Push Button Configuration) method ................................................. 14

3.2.2 PIN method ................................................................................................. 16

3.3 To connect using Windows built-in wireless utility .................................................. 18

3.3.1 In Windows XP ........................................................................................... 18

3.3.2 In Windows 7 .............................................................................................. 20

3.3.3 In Windows 8 .............................................................................................. 22

3.3.4 In Windows 8.1 ........................................................................................... 24

Chapter 4 Management ........................................................................................ 27

4.1 Profile ....................................................................................................................... 27

4.1.1 Add a profile ............................................................................................... 27

4.1.2 Modify a profile ........................................................................................... 32

4.1.3 Delete a profile ........................................................................................... 32

4.2 Advanced ................................................................................................................. 32

4.3 About ....................................................................................................................... 33

Chapter 5 AP Mode .............................................................................................. 34

Chapter 6 Uninstall Software ............................................................................... 37

6.1 In Windows XP/7 ..................................................................................................... 37

6.1.1 Uninstall the utility software from your PC ................................................. 37

6.1.2 Uninstall the driver software from your PC ................................................ 39

6.2 In Windows 8/8.1 ..................................................................................................... 40

6.2.1 Uninstall the utility software from your PC ................................................. 40

6.2.2 Uninstall the driver software from your PC ................................................ 42

Appendix A: Specifications ................................................................................... 44

Appendix B: Glossary ............................................................................................ 45

Archer T4U TP-LINK Wireless USB Adapter User Guide

Package Contents

Please verify that all the package contents below are available.

One Archer T4U AC1200 Wireless Dual Band USB Adapter

Quick Installation Guide

USB Extension Cable

One Resource CD for Archer T4U, including:

• TP-LINK Wireless Configuration Utility (TWCU) and Drivers

• User Guide

• Other helpful information

Make sure that the above items are contained in the package. If any of the above items is damaged or missing, please contact your distributor.

Note:

The ‘adapter’ mentioned in this User Guide stands for Archer T4U AC1200 Wireless Dual Band

USB Adapter without any explanation.

1

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Chapter 1 Product Overview

1.1 Introduction

The adapter is a dual band 802.11ac client device designed to deliver a high-speed wireless performance for your desktop. With a faster wireless connection, you can get a better Internet experience, such as downloading, gaming, and video streaming.

With the 802.11ac technology, higher throughput improvements using 2T2R, the Archer T4U’s auto-sensing capability allows high packet transfer rate of up to 867Mbps for maximum throughput. It has good capability on anti-jamming, and it can also interoperate with other wireless

(802.11a/b/g/n/ac) products. The adapter supports WEP, WPA-PSK/WPA2-PSK and WPA/WPA2 encryption to prevent outside intrusion and protect your personal information from being exposed.

The adapter is easy to install and manage. The Quick Setup Wizard will guide you step-by-step through the installation process and the TP-LINK Wireless Configuration Utility (TWCU) will instruct you to quickly set up a wireless connection.

With unmatched wireless performance, reception, and security protection, the Archer T4U is the best choice for easily adding or upgrading wireless connectivity to your desktop.

1.2 Features

 Complies with IEEE 802.11ac.

 Provides USB 3.0 interface

 Supports dual-band, 2.4GHz or 5GHz

 Seamlessly compatible with 802.11a/b/g/n/ac products

 Experience smoother video streaming and online gaming by choosing the clearer 5GHz band for wireless connections

 Supports 64/128 WEP, WPA/WPA2, WPA-PSK/WPA2-PSK(TKIP/AES), supports IEEE

802.1x

 Supports Windows XP 32/64bit, Windows 7 32/64bit, Windows 8 32/64bit, windows 8.1

32/64bit

 Supports ad-hoc and infrastructure mode

 Bundled utility provides quick & hassle-free installation

2

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

1.3 Hardware Overview

LED status:

Status Working Status

Off

The driver has not been installed;

The adapter's radio has been disabled.

Flashing Slowly The driver has been installed but no data is being transmitted or received.

Flashing Quickly Data is being transmitted or received.

3

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Chapter 2 Installation

Please install the adapter into your computer before installing the driver and utility software from the Resource CD.

2.1 Hardware Installation

There are two methods:

Method One:

Plug the adapter into an available USB interface on your computer directly.

Method Two:

Connect the adapter and your computer with the provided USB extension cable.

When the Found New Hardware wizard appears, click Cancel.

Note:

When the hardware has been successfully installed on your computer, you may be prompted

'

Found New Hardware Wizard' (as shown in Figure 2-1); please click Cancel, and then follow

the Software Installation steps to install driver and utility for your adapter.

4

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 2-1 Found New Hardware Wizard in Windows XP

2.2 Software Installation

The adapter’s Setup Wizard will guide you through the installation procedures for Windows XP,

Windows 7, Windows 8 and Windows 8.1. The procedures in different systems are quite similar, therefore here we use the procedures in Windows 7 as an example.

1. Insert the Resource CD into your CD-ROM drive and then select model Archer T4U on the

window that pops up (as shown in the below Figure 2-2).

There will be a menu including:

Install Driver and Utility and User Guide. Click Install Driver and Utility to begin.

Figure 2-2

2. The InstallShield Wizard window will appear. Click Next to continue.

5

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 2-3

3. Choose a setup type. It is recommended to select Install TP-LINK Wireless

Configuration Utility and Driver. Selecting Install Driver Only can only install driver.

Click Next to continue.

Figure 2-4

4. Click Change to specify the destination location for the software or you can leave it default.

Click Next in the screen below to continue.

6

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

5. Click Install to continue the setup.

Figure 2-5

Figure 2-6

6. The utility and drivers will install. It may take 1~2 minutes.

7

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 2-7

7. After all the steps above, you will see the screen below. Click Finish to complete the setup.

Figure 2-8

8. After installation, the utility configuration page will automatically pop up as shown in the following figure and the icon will appear in your system tray. To connect to a network, please refer to

Chapter 3 Connect to a Wireless Network .

8

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 2-9

9

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Chapter 3 Connect to a Wireless Network

With both the hardware and software successfully installed into your computer, you can quickly connect to a wireless network using one of the following methods.

Method One: To connect using TWCU (TP-LINK Wireless Configuration Utility)

Archer T4U uses the TWCU as the management software. The utility provides you an easy interface to connect to a network and to change any settings related to the wireless adapter.

Method Two: To connect using WPS

By this method, you can connect to your network quickly on the condition that your Router or access point supports WPS or QSS as is called by some other products.

Method Three: To connect using Windows built-in wireless utility

Windows users may use the built-in wireless utility to connect to a wireless network. For specific

operations, please go to Section 3.3 To connect using Windows built-in wireless utility .

3.1 To connect using TWCU

1. After installation, the utility configuration page will automatically pop up on the screen. If the utility page does not pop up, you can also launch the utility by double-clicking the icon on your desktop.

Figure 3-1

2. The Network page will display all wireless networks that are available in your area. To connect to a network, simply highlight the wireless network name (SSID) and click

Connect. If you tick Connect automatically, the adapter will automatically connect to your target network next time.

10

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 3-2

3. You will be prompted different windows when you choose wireless network of different security types.

1) Wireless network of WPA/WPA2-Personal

If you selected a wireless network of the security type WPA/WPA2-Personal, you will be

prompted to enter the password in the security key field, as shown in Figure 3-3. Or you

can push the WPS/QSS button on your Router (if it features the WPS/QSS function) to quickly build a connection without entering the security key (password).

Figure 3-3

Note:

The security key (password) can be found on the configuration page of your Router or Access

Point.

2) Wireless network of WPA/WPA2-Enterprise

If you selected a wireless network of the security type WPA/WPA2-Enterprise, you will be prompted to choose a type of authentication, either Certificate or Password. With

11

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Certificate as your authentication, you need to select one specific certificate from the

drop-down list, as shown in Figure 3-4. With

Password as your authentication, you should enter the right user name and password in the corresponding field, as shown in Figure 3-5.

Figure 3-4

Figure 3-5

3) Wireless network of None

If you selected a wireless network of None (that is, no security is set.), you can get directly connected to this network without any further configuration.

12

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

4. Please wait a few minutes for the connection process.

Figure 3-6

5. You have now successfully connected to your network. Click Close to enjoy the Internet.

Figure 3-7

6. To view more information about the network currently connected, click Status in the tools section and the page will display information such as the network type, channel, rate, etc.

13

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 3-8

3.2 To connect using WPS

WPS (Wi-Fi Protected Setup) function allows you to add a new wireless device to an existing network quickly.

If your wireless Router supports WPS or QSS (Quick Security Setup), you can establish a wireless connection between wireless card and Router using either Push Button Configuration

( PBC) method or PIN method. Three WPS connection methods are listed in the following parts.

3.2.1 PBC (Push Button Configuration) method

1. Press the WPS or QSS button on the Router. Here we use Router Archer C7 as an example. Press the WPS/Reset button for 2~3 seconds.

2. Open TWCU and click WPS tab. Select Push the button on my access point or wireless

router and then click Connect.

14

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 3-9

3. The adapter will be connecting to the target network.

Figure 3-10

4. When the following window appears, you have successfully connected to the network.

Figure 3-11

15

3.2.2 PIN method

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

There are two ways to configure the WPS by PIN method:

1) Enter the PIN from your Router or AP device.

2) Enter a PIN into your Router or AP device.

Following are the detailed configuration procedures of each way.

3.2.2.1. Enter the PIN from your Router or AP device

1. Open TWCU and click WPS tab. Select Enter the PIN of my access point or wireless

router. In the empty field beside PIN, enter the PIN labeled on the bottom of the Router

(here takes 13492564 for example). If you have generated a new PIN code for your Router, please enter the new one instead. Click Connect to continue.

Figure 3-12

2. The adapter will be connecting to the target network.

Figure 3-13

3. When Figure 3-11 appears, you have successfully connected to the network.

16

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

3.2.2.2. Enter a PIN into your AP device

1. Open TWCU and click WPS tab. Select Enter the PIN of this device into my access

point or wireless router. In the field beside PIN, you will see the PIN value of the adapter which is randomly generated. Click Connect to continue.

Figure 3-14

2. Open your Router’s Web-based Utility and click WPS link on the left of the main menu.

Then click Add device and the following figure will appear. Enter the PIN value of the adapter in the empty field beside PIN and then click Connect.

Figure 3-15

3. When

Connect successfully appears on the screen (as shown in Figure 3-16), the WPS

configuration is completed. Or you can view the adapter’s utility page to see whether the

connection has been successful (as shown in Figure 3-17).

17

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 3-16

Figure 3-17

3.3 To connect using Windows built-in wireless utility

3.3.1 In Windows XP

Windows XP users may use the built-in wireless utility. Follow the steps below.

1. Right-click on the utility icon in your system tray (lower-right corner). Select Switch to

Windows wireless configuration tool.

Figure 3-18

18

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Or double-click the utility icon to load the utility configuration page. Click Advanced in the tools section and then select Use Windows wireless configuration tool in the figure shown below. Click

OK when Figure 3-20 appears to continue.

Figure 3-19

Figure 3-20

2. Right-click on the wireless computer icon in your system tray (lower-right corner). Select

View Available Wireless Networks.

Figure 3-21

3. The utility will display any available wireless networks in your area. Click on a network

(displayed using the SSID) and click the Connect button.

19

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 3-22

4. If the network is security-enabled, you will be prompted to enter the key as shown below. If not, you will connect to the network directly without entering a key.

Figure 3-23

3.3.2 In Windows 7

Windows 7 users may use the built-in wireless utility. Follow the steps below.

1. Left-click the wireless icon in your system tray (lower-right corner). The utility will display any available wireless networks in your area. Highlight the wireless network

(displayed using the SSID) to be connected and then click Connect.

20

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 3-24

2. If the network you would like to connect is encrypted, enter the same security key or passphrase that is on your Router. Or push the WPS/QSS button on the Router or access point (You will be prompted to push the button on the window if WPS function is supported as shown in the figure below). If the network to be connected is not secure, the connection will be built without entering a key.

Figure 3-25

21

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

3. You have now successfully connected to the network.

Figure 3-26

3.3.3 In Windows 8

Windows 8 users may use the built-in wireless utility. Follow the steps below.

1. Click the icon at the bottom of your screen, and a network list will appear at the right side of your screen. Select your target network, and then click Connect.

Figure 3-27

2. If the network is unencrypted, you will directly connect to it.

If the network is encrypted, enter the password (network security key) and then click Next to continue.

22

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 3-28

Note:

You can also push the WPS/QSS button on your router as hinted “You can also connect by pushing the button on the router”. Then click Next to continue.

3. When Connected appears behind the SSID (as shown below), you have successfully connected to the target network.

Figure 3-29

Note:

If the adapter is connected to the network for the first time, you will be asked whether to turn on sharing or connect to devices. Please select “Yes, ...”or “No, ...” according to your Internet environment.

23

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 3-30

3.3.4 In Windows 8.1

Windows 8.1 users may use the built-in wireless utility. Follow the steps below.

1. Click the icon at the bottom of your screen, and a network list will appear at the right side of your screen. Select your target network, and then click Connect.

Figure 3-31

2. If the network is unencrypted, you will directly connect to it.

If the network is encrypted, enter the password (network security key) and then click Next to continue.

24

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 3-32

Note:

1) You can also push the WPS/QSS button on your router as hinted “You can also connect by pushing the button on the router”. Then click Next to continue.

2) You can also enter the PIN from your router as hinted “Connect using a security key instead”. Then click Next to continue.

Figure 3-33

3. When Connected appears behind the SSID (as shown below), you have successfully connected to the target network.

25

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 3-34

Note:

If the adapter is connected to the network for the first time, you will be asked whether to connect to devices. Please select “Yes” or “No” according to your Internet environment.

Figure 3-35

26

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Chapter 4 Management

This section will show you how to configure your Archer T4U adapter using the TP-LINK

Wireless Configuration Utility (TWCU).

The Archer T4U adapter uses the TP-LINK Wireless Configuration Utility as the management software. The utility provides users with an easy interface to change any settings related to the adapter. Double-clicking on the icon on your desktop will start the utility.

4.1 Profile

Your wireless networks may vary in different places like home, office or coffee shop. With

Profile management, you can easily save and manage various networks to be connected, saving you the trouble of having to repeat the same configurations. Click Profile in the tools section, the following page will appear.

Figure 4-1

4.1.1 Add a profile

To add a profile, click the Add button on the bottom of the screen. Then the configuration window will appear.

4.1.1.1. Add a profile in Infrastructure mode

If you are connecting to a wireless router or access point, select Infrastructure as the Network

Type in the screen that appears and follow the instructions below to finish the setting.

27

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 4-2

Figure 4-3

The following items can be found on the screen.

Profile Name: Enter a name for your profile (e.g. Home, Office, Coffee Shop). The same name is not allowed. Please also note that no space is allowed between words.

SSID: Select the target network from the drop-down list.

Network Type: Select the network type. If you are connecting to a wireless Router or access point, select Infrastructure. If you are connecting to another wireless client such as an adapter, select ad-hoc.

Security Type: Select the security type from the list. Four options are available:

WPA-PSK/WPA2-PSK, WPA/WPA2, WEP and None. The security type should be the same as on your Router or access point, otherwise, you will not be able to build a successful connection. WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key must be the exact same key entered on your wireless

Router or access point. None stands for no security. It’s recommended to enable

WPA-PSK/WPA2-PSK on your wireless Router or access point before con is configuring your wireless adapter.

28

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Note:

You will see Figure 4-2 if you selected the security type WPA-PSK/WPA2-PSK; while, if you selected the security type WPA/WPA2, Figure 4-3 will be displayed.

Encryption Type: From the drop-down menu, select the encryption type that is the same as on your Router or access point.

Security Key: Enter the passphrase exactly as it is on your wireless Router or access point. Click the Show characters box to see the passphrase, or uncheck this box to hide it.

Authentication: Select a type of authentication, either certificate or password.

Certificate: If you select certificate as your Authentication, then you need to specify your certificate from the drop-down list here.

Start this connection automatically: Check this box to automatically connect to this network next time.

Save: Click Save to save your settings.

Having completed the above settings, the Profile page should look like the following figure. To connect to a desired network, just highlight the network you would like to connect to and click the Connect button on the bottom of the window. Then click OK in Figure 4-5 to activate the profile.

Figure 4-4

Figure 4-5

29

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

4.1.1.2. Add a profile in ad hoc mode

If you are connecting to another wireless client such as an adapter, select ad hoc as the

Network Type in the screen that appears and follow the instructions below to finish the setting.

Figure 4-6

The following items can be found on the screen.

Profile Name: Enter a name for your profile e.g. Home, Office, Coffee Shop. The same name is not allowed. Please also note that no space is allowed between words.

SSID: Select the target network from the drop-down list.

Network Type: Select the network type. If you are connecting to a wireless router or access point, select Infrastructure. If you are connecting to another wireless client such as an adapter, select ad hoc.

Band: This item determines which operating frequency will be used. Two options are available: 2.4Ghz and 5Ghz. It is recommended that your computers and devices running video and voice applications use the 5Ghz band, while your guest access and computers

 that are only browsing the web use the 2.4Ghz band.

2.4Ghz - You can use the 2.4GHz band to connect to many classic wireless devices like gaming consoles, laptops, DVRs, ect.

5Ghz - This band is less crowded and is used for time-sensitive music, video streaming or gaming. Using this band can avoid interference with 2.4GHz networks or noisy devices like cordless phones and microwave ovens.

Security Type: Select the security type from the list. Two options are available: WEP and

None. None stands for no security. It is recommended that you select WEP to secure your wireless network.

Encryption Type: If you select None as the Security Type, the Encryption Type will be

None accordingly. If you select WEP as the Security Type, the Encryption Type will be

Open.

Key Index: You can select ASCII or Hexadecimal format on the right. ASCII format stands for any combination of keyboard characters in the specified length. Hexadecimal format stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length.

30

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

For 64-bit encryption - You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 5 ASCII characters.

For 128-bit encryption - You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not permitted) or 13 ASCII characters.

Security Key: Enter the passphrase. Click the Show characters box to see the passphrase. Unchecking it will hide it.

Start this connection automatically: Check this box to automatically connect to this network next time.

Save: Click Save to save your settings.

Having completed the above settings, the Profile page should looks like the following figure. To connect to a desired network, just highlight the network you would like to connect to and click the Connect button on the bottom of the window. Then click OK in Figure 4-8 to activate the profile.

Figure 4-7

Figure 4-8

31

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

4.1.2 Modify a profile

You may edit an existing profile by clicking the Modify button from the Profile page. For instance, you may like to change the profile name from Home to Home1 or you may want to specify another SSID for profile Home. After all the changes, click Save to make the changes take effect.

Figure 4-9

4.1.3 Delete a profile

To delete an existing profile, highlight the profile name and click Remove on the bottom of the screen or press the Delete button on your keyboard. When the following figure appears, click

OK to continue.

Figure 4-10

4.2 Advanced

The following configurations can be made on the Advanced page:

1) To select wireless configuration tool.

Here you can decide which tool to use, either the TP-LINK Configuration Utility or the

Windows wireless configuration tool. (This option is available only in Windows XP.

)

2) To switch to another wireless network adapter.

32

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Here you can switch to another adapter installed in your computer. The adapters successfully installed in your computer will be listed in the drop-down list if the adapters are supported by this utility.

3) To switch to SoftAP mode.

Once enabled, the adapter will be able to work as an AP.

4) To change the power save mode. The default option is OFF.

Figure 4-11

4.3 About

The About screen gives you some information about the Driver and Utility versions of the adapter. Right-click the icon in your system tray and select About from the list.

Figure 4-12

Figure 4-13

33

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Chapter 5 AP Mode

In Soft AP mode, the adapter will work as an AP.

Suppose that only one computer in your house can access the Internet for various reasons like only one WLAN port is available on your wired broadband Router, however, other wireless-capable devices also want to share the Internet. Then the adapter can be configured as an AP under the Soft AP mode, saving you the trouble of having to get a separate access point or a Router.

With this feature, a computer can use a single physical wireless adapter to connect as a client to a hardware access point while at the same time acting as a software AP allowing other wireless-capable devices to connect to it.

To switch to this mode, right-click on the utility icon in your system tray and select Switch to

SoftAP mode.

Figure 5-1

Or from the Advanced page of the utility, tick ON under the SoftAP mode as shown in the following figure. Click OK when prompted to confirm the setting.

Figure 5-2

34

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

The Soft AP icon then will appear beside Advanced icon in the utility.

Figure 5-3

Figure 5-4

SoftAP mode: Select to enable or disable the function.

Internet Connecting Share (ICS): Specify a connection through which devices connected to your AP can access the Internet.

SSID: Enter the name for your soft AP (for example, Jone) so that others can know which

AP is yours when trying to connect to it.

Security Type: The security type here is set to be WPA2-PSK which is based on 802.11i and uses AES (Advanced Encryption Standard) instead of TKIP. It was designed to improve the security features of WEP. WPA2-PSK uses a passphrase or key to authenticate your wireless connection. You needn’t make any configuration here.

Encryption Type: The encryption type here is set to be AES.

Security Key: Enter the Key in the field to make your AP security enabled. It is recommended that you specify another key instead of the default key 12345678. Only by entering the corresponding key can other computers establish a successful connection with your AP.

IP Address: Here displays the IP address of the SoftAP.

35

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Having completed the above settings, click

Apply; then Figure 5-4 will pop up, where you click

OK to make Soft AP mode take effect.

36

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Chapter 6 Uninstall Software

6.1 In Windows XP/7

The software uninstall steps are similar in Windows XP, and Windows 7, here we just use

Windows 7 as an example.

6.1.1 Uninstall the utility software from your PC

1. On the Windows taskbar, click the Start button, click All programsTP-LINK, and then click Uninstall-TP-LINK Wireless Configuration Utility.

Figure 6-1 Uninstall Utility

2. Click Yes to start uninstalling the utility software from your PC.

Figure 6-2

37

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

3. It may take a few minutes to undergo the whole un-installation process.

Figure 6-3

4. Click Finish when the figure below appears.

Figure 6-4

38

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

6.1.2 Uninstall the driver software from your PC

1. On the Windows taskbar, click the Start button, click All programsTP-LINK, and then click Uninstall-TP-LINK Archer T4U Driver.

Figure 6-5 Uninstall Driver

2. Click Yes to start uninstalling the driver software from your PC.

Figure 6-6

39

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

3. It may take a few minutes to undergo the whole un-installation process.

Figure 6-7

4. Click Finish when the figure below appears.

Figure 6-8

6.2 In Windows 8/8.1

The software uninstall steps are similar in Windows 8 and Windows 8.1. Here we just use

Windows 8 as an example.

6.2.1 Uninstall the utility software from your PC

1. Enter the Apps interface, and find the TP-LINK application, then click Uninstall- TP-LINK

Wireless Configuration Utility.

40

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Figure 6-9

2. Click Yes to start uninstalling the utility software from your PC.

Figure 6-10

3. It may take a few minutes to undergo the whole un-installation process.

Figure 6-11

41

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

4. Click Finish when the figure below appears.

Figure 6-12

6.2.2 Uninstall the driver software from your PC

1. Enter the Apps interface, and find the TP-LINK application, then click Uninstall-TP-LINK

Archer T4U Driver.

Figure 6-13

2. Click Yes to start uninstalling the driver software from your PC.

Figure 6-14

42

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

3. It may take a few minutes to undergo the whole un-installation process.

Figure 6-15

4. Click Finish when the figure below appears.

Figure 6-16

43

Archer T4U TP-LINK Wireless USB Adapter User Guide

Appendix A: Specifications

Normal

Interface

Standards

Operating System

Throughput

Data Security

Frequency *

Safety & Emissions

USB 3.0 Interface

IEEE802.11a; IEEE802.11b; IEEE802.11g; IEEE802.11n;

IEEE802.1x, IEEE802.11ac

Windows XP, Windows 7, Windows 8, Windows 8.1

2.4GHz:300Mbps (Maximal)

5GHz: 867Mbps (Maximal)

WEP, WPA / WPA2, WPA-PSK / WPA2-PSK

2.4 ~ 2.4835 GHz, 5.15~5.25GHz,

5.25~5.35GHz, 5.475~5.725GHz, 5.745~5.825GHz

FCC, CE, WIFI, IC, NCC, WHQL

Environmental and Physical

Working Temperature 0℃~ 40℃ (32℉~104℉)

Storage Temperature

Working Humidity

Storage Humidity

-40℃~70℃(-40℉~158℉)

10% ~ 90% RH, Non-condensing

5% ~ 90% RH, Non-condensing

* 1.

Only 2.412GHz~2.462GHz is allowed to be used in USA, which means only channel 1~11 is available for American users to choose.

* 2. Rules on the use of 5GHz band channels may vary according to different national laws.

44

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Appendix B: Glossary

802.11ac - IEEE 802.11ac is a wireless computer networking standard of 802.11.This specification will enable multi-station WLAN throughput of at least 1 gigabit per second .This is accomplished by extending the air interface concepts embraced by

802.11n: wider RF bandwidth, more MIMO spatial streams, multi-user MIMO, and high-density modulation (up to 256 QAM).

802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium

(EWC) was formed to help accelerate the IEEE 802.11n development process and promote a technology specification for interoperability of next-generation wireless local area networking

(WLAN) products.

802.11g - specification for wireless networking at 54 Mbps using direct-sequence spread-spectrum (DSSS) technology, using OFDM modulation and operating in the unlicensed radio spectrum at 2.4GHz, and backward compatibility with IEEE 802.11b devices, and WEP encryption for security.

802.11b - The 802.11b standard specifies a wireless product networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks.

802.11a - specification for wireless networking at 54 Mbps using OFDM modulation and operating in radio band at 5GHz.

Ad hoc Network - An ad hoc network is a group of computers, each with a Wireless Adapter, connected as an independent 802.11 wireless LAN. Ad hoc wireless computers operate on a peer-to-peer basis, communicating directly with each other without the use of an access point.

Ad hoc mode is also referred to as an Independent Basic Service Set (IBSS) or as peer-to-peer mode, and is useful at a departmental scale or SOHO operation.

DSSS - (Direct-Sequence Spread Spectrum) - DSSS generates a redundant bit pattern for all data transmitted. This bit pattern is called a chip (or chipping code). Even if one or more bits in the chip are damaged during transmission, statistical techniques embedded in the receiver can recover the original data without the need of retransmission. To an unintended receiver,

DSSS appears as low power wideband noise and is rejected (ignored) by most narrowband receivers. However, to an intended receiver (i.e. another wireless LAN endpoint), the DSSS signal is recognized as the only valid signal, and interference is inherently rejected (ignored).

FHSS - (Frequency Hopping Spread Spectrum) - FHSS continuously changes (hops) the carrier frequency of a conventional carrier several times per second according to a pseudo-random set of channels. Because a fixed frequency is not used, and only the transmitter and receiver know the hop patterns, interception of FHSS is extremely difficult.

45

Archer T4U AC1200 Wireless Dual Band USB Adapter User Guide

Infrastructure Network - An infrastructure network is a group of computers or other devices, each with a Wireless Adapter, connected as an 802.11 wireless LAN. In infrastructure mode, the wireless devices communicate with each other and to a wired network by first going through an access point. An infrastructure wireless network connected to a wired network is referred to as a Basic Service Set (BSS). A set of two or more BSS in a single network is referred to as an Extended Service Set (ESS). Infrastructure mode is useful at a corporation scale, or when it is necessary to connect the wired and wireless networks.

Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems.

It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise.

There are two main alternatives, Direct Sequence Spread Spectrum (DSSS) and Frequency

Hopping Spread Spectrum (FHSS).

SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name. See also Wireless Network

Name and ESSID.

WEP - (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit or

152-bit shared key algorithm, as described in the IEEE 802.11 standard. To gain access to a

WEP network, you must know the key. The key is a string of characters that you create.

When using WEP, you must determine the level of encryption. The type of encryption determines the key length. 128-bit encryption requires a longer key than 64-bit encryption.

Keys are defined by entering in a string in HEX (hexadecimal - using characters 0-9, A-F) or

ASCII (American Standard Code for Information Interchange – alphanumeric characters) format. ASCII format is provided so you can enter a string that is easier to remember. The

ASCII string is converted to HEX for use over the network. Four keys can be defined so that you can change keys easily.

Wi-Fi - A trade name for the 802.11b wireless networking standard, given by the Wireless

Ethernet Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standards group promoting interoperability among 802.11b devices.

WLAN - (Wireless Local Area Network) - A group of computers and associated devices communicate with each other wirelessly, which network serving users are limited in a local area.

WPA - (Wi-Fi Protected Access) - A wireless security protocol uses TKIP (Temporal Key

Integrity Protocol) encryption, which can be used in conjunction with a RADIUS server.

46

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • Ultra-fast Wi-Fi – 1300Mbps wireless speeds (400Mpbs on the 2.4GHz band and 867Mbps on the 5GHz band) with support for the next generation 802.11ac Wi-Fi standard*
  • Dual Band Wireless - 2.4GHz and 5GHz bands for flexible connectivity
  • High gain antennas – Improved range, signal quality and transmission performance
  • MU-MIMO –Delivers highly efficient wireless connection**
  • Super Speed USB 3.0 Port - Up to 10x faster transfer speeds than USB 2.0
  • WPS Button - Easy wireless security encryption at the push of the WPS button

Related manuals

Download PDF

advertisement