TP-LINK TL-WR700N Wireless N Mini Pocket Router Quick Installation Guide
Below you will find brief information for Wireless N Mini Pocket Router TL-WR700N. This compact router offers three working modes: AP, Router, and Repeater, extending your Wi-Fi range and enabling multiple users to share internet access. It features a user-friendly interface for quick setup and basic network configuration, along with a LED indicator to display connection status. The TL-WR700N is ideal for extending existing networks or creating a small home network.
PDF
Download
Document
Advertisement
Advertisement
TP-LINK The Reliable Choice Quick Installation Guide 150Mbps Wireless N Mini Pocket Router MODEL NO. TL-WR700N 7106503681 Package Contents = 0 ZZ =n TL-WR700N Ethernet Cable “= == Resource CD QIG Hardware Introduction В Repeater Mode Before hardware connection, please write down the SSID and Password of your Router on the label for TL-WR700N is used to extend the range of wireless signal of the existing AP or wireless router. In this mode, the only wired port works as LAN. The SSID later use. Both are case-sensitive. of TL-WR700N is the same as that of the device you repeat. The DHCP server is disabled by default in this mode. NVA ARR 120000000000 DOGO NANO MAC:40169F2046F2 SSID:TP-LINK_2046F2 (С, Password:9F2046F2 SSID: abc SSID+abc У) (CHEN MAC:40169F2046F2 SSID:TP-LINK_2046F2 Password:9F2046F2 *% SSID: Wireless Network Name of TL-WR700N. * Password: Pre-encryption password of TL-WR700N. Three Typical Working Modes ED AP Mode As the supplement of wired LAN, TL-WR700N enables the wired LAN to connect to the Internet wirelessly. The default mode of TL-WR700N is AP. In this mode, the only wired port works as LAN. The DHCP server is disabled by default in this mode. If you want to log in the management page, please set your computer’s IP address manually. Wired Network © * This hardware connection is applied in AP Mode and Router Mode only. Step 1: Connect the LAN/WAN port of TL-WR700N to Internet with an Ethernet cable. Step 2: Plug in standard electrical wall socket directly to power the Router. EJ Router Mode As a wireless router, TL-WR700N enables multi-user to share Internet via DSL/Cable Modem. In this mode, the only wired port works as WAN, which can be connected to DSL/Cable Modem with an Ethernet cable. Computers could connect to the device by only wireless way. DHCP server is enabled by default. TL-WR700N LED: Status Indication It's powered on but the LAN/WAN port is not connected. The LAN/WAN cable is connected but there is no data being transmitted or received. The LAN/WAN cable is connected and there is Solid Flashing Slowly Flashing Quickly data being transmitted or received. — —— Cm o щи Reset: It is used to reset the Router to its factory defaults. LAN/WAN: This port works as LAN in AP/Repeater/ Bridge/Client mode and as WAN in Router mode. Note For more detailed information about Reset, please refer to Appendix: Troubleshooting. Instant Wireless Connection (This method is for connecting to the default AP Mode. If you want to configure AP Mode or choose other modes, please skip to Advanced Web Management.) For Windows 7 For Windows XP . . . к Click the wireless icon Y at the bottom of your desktop. Click Refresh network list, and then select the network. Click Connect. Enter the Network key, and then Confirm network key. Click Connect. If you can see Connected as shown in the following screen, youve successfully connected to the Click the icon E at the bottom of your desktop. Click refresh button, and then select the target pinMireloss ohm Convectión 16 Wireless Network Connection The network. TP-LINK_2046F2' requi kk |: lled key or WPA key), network ke i i i Type the key, and then click Connect. Network key: | ........ | Confirm network key: | ........ | Connect Cancel 1. Note 2. on the label. The password is case-sensitive. wireless network. as AR etresh noter iat Click an ize q q Wireless $ 520 rty-enabled wwaless retuark (WWA) wall Wireless TP LINK “» +7 sao rity-enabled wirless returric(WPa) TP q LINE “| Connecte <A Set up à wireless wetwork To LINK 208452 » - =0.rity-enabled wiraless retar (WPA) ol = The default SSID of the network is TP-LINK_x>0000x. (The TP-LINK_000ax is the SSID on the label.) In AP mode, the pre-encryption function is opened by default and the default Network key/Security key is the Password Advanced Web Management (Here we take Windows 7 as an example.) 1 Configure PC о Go to Start > Control Panel > View network status and tasks > Change adapter settings. Right click Wireless Network Connection, and select Properties. Double click Internet Protocol Version 4 (TCP/IPv4) in the item list. Ü Wireless Network Connection Properties Networking | Sharing Connect using: A Wireless Network Connection = на Mot connected À fil Microsc a] Disable Status к Realtek 8185 Extensible 802.11b/9 Wireless Device #2 This connection uses the following items: 0% Client for Microsoft Networks El dos Packet Scheduler ¡El File and Printer Sharing for Microsoft Networks Create Shortcut Ya. temer Proaza Version op et Prof ET E) Delete Intemet Protocol Version 4 (TCP/IPv4) 2 Tnk-Cayer Topology DI Mapper 1/0 Driver Hy Rename a. Link-Layer Topology Discovery Responder [6 Properties | Description Transmission Control Protocol/Intemet Protocol. The default Uninstall across diverse interconnected networks. Specify the IP address as 192.168.0.x (x is from 1 to 253), and the Subnet mask as 255.255.255.0. Type the Router's LAN IP address (the default IP is 192.168.0.254) into the Default gateway field. Click OK. Internet Protocol Version 4 (TCP/IPv4) Properties General You can get IP i i i ically if your k this capability. Otherwise, you need to ask your network administrator for the appropriate IP settings. (E) Obtain an IP address automatically {@) Use the following IP address: IP address: 192 .168 . 0 . 20 Subnet mask: 255 .255 ‚255, 0 Default gateway: 192 . 168 . 0 .754 Obtain DNS server address automatically (8) Use the following DNS server addresses: Preferred DNS server: Alternate DNS server: [И] validate settings upon exit [к] сена) network. Click Connect. Currently connected to: E TP-LINK Network Fo No Internet access Wireless Network Connection 2 A IS TP-LINK_Network „A TP-LINK_2046F2 a | apple_lee TP-LINK 656D4E WPS000051e32c Al ChinaMet-uWLC Open Network and Sharing Center Note El Enter the Security key. Click OK. If you can see Connected as shown in the following screen, you've my Connect to a Network Type the network security key Security key: Hide characters Connect to Network Click the wireless icon Е" at the bottom of your desktop. Click refresh button, and then select the target network. Click Connect. Currently connected to: En = TP-LINK_Network "No Internet access Wireless Network Connection 2 a = TP-LINK_Network „A TP-LINK_2046F2 A | E omar [tama] 1123 "1 | apple_lee A TP-LINK_656D4E „al | WP5000051e32c 1] | ChinaNet-uWLC "A Open Network and Sharing Center я Enter the Security key. Click OK. successfully connected to the wireless network. Currently connected to: * = TF-LINK_2046F2 7 Mo Internet access Wireless Network Connection 2 a |5 TP-LINK_2046F2 Al TP-LINK_Network „MM Network Al 1123 Al TP-LINK_656D4E ll] TP-LINK_756796 A | WPS000051 e32¢ al ChinaNet-uWLC MM Open Network and Sharing Center If you can see Connected as shown in the following screen, you've successfully connected to the wireless network. fe Connect to a Network Type the network security key Security key: Hide characters Currently connected to: = TP-LINK_2046F2 "No Internet access Wireless Network Connection 2 A 3 TP-LINK_2046F2 | || TP-LINK_Network A Network oN || na il TP-LINE_656D4E A TP-LINK_756736 a || WPS000051e32c ll ChinaNet-uWLC | Open Network and Sharing Center 1. The default SSID of the network is TP-LINK_xxxxxx. (The TP-LINK_xxxxxx is the SSID on the label.) 2. In AP mode, the pre-encryption function is opened by default and the default Security key is the Password on the label. The password is case-sensitive. 3 Configure Router AP Mode о Open a Web browser, type 192.168.0.254 in the address field, and press Enter. At the prompt, enter the default User Name and Password: admin, both in lower case letters. Click OK. |= The server 192.168.0.254 at TP-LINK Wireless N Router WR700N requires a username and password, A Windows Security d password be Warning: This server is requesting that your (basi henti without a secure sent in an i connection). [7] Remember my credentials Configure the Wireless Settings according to the mode you chose. After a successfully login, you can click the Quick Setup menu to quickly configure your Router. Click Next. El Choose the Working Mode you need, and then click Next. The quick setup will tell you how to configure the basic network parameters. To continue, please click the Next button. To exit, please click the Exit button. Quick Setup - Working Mode O AP: AP Mode O Router: Router Mode O Repeater: Repeater Mode O Bridge: Bridge Mode O Client: Client Made Back Next (TL-WR700N supports five working modes. Here we introduce three modes, including AP, Router and Repeater. For Bridge and Client, please refer to User Guide in the Resource CD.) Set the wireless parameters. It's recommended that you rename an SSID, choose a Security Type and enter a Password. O Click Reboot to reboot the Router and make the settings take effect. After the rebooting, please reconnect to the network according to Step 4 Reconfigure PC and Step 5 Reconnect to Network. If Wireless Security is enabled, you need to enter Note . . the password you've just set to sucessfully finish the connecting. Wireless Radio: ca Congratulations! The Router is now connecting you to the Internet. For detail settings, e A please click other menus if necessary. — Incorrect selings may cause interference The change of wireless config will not take effect until the Router reboot. Channel: crm [Back [Crewe] Security Options: Disahle Security © WPA PSKWPAZ PSK PSK Password: © No Change Next Router Mode Set the wireless parameters. It's recommended that you rename a) If PPPoE is selected, please enter the User Name and Password © Click Reboot to reboot the Router and make the settings take о an SSID, choose a Security Type and enter a Password. Quick Setup - Router vos Rad 550: TP-LINK_2046F2 : Warning: Ensure you select à correct country to conform local Lay. Incarrect settings may cause interference Mode: 11bgn mixed м Channel Width: Auto v Security Options: Disable Security WPA-PSKMWPAZ PSK PSK Password: 9F2046F2 © No Change Choose your WAN Connection Type and click Next to continue. Quick Setup - WAN Connection Type given by your ISP. These fields are case-sensitive. Then click Next. Quick Setup - PPPoE effect. Quick Setup - Finish Congratulations! The Router is now connecting you to the Internet. For detail settings, please click other menus if necessary. The change of wireless config will not take effect until the Router reboot. Back Next b) If Dynamic IP is selected, the Router gets the IP address automatically from the DHCP server or the ISP. No configuration should be set and you can go on with the wireless configuration. с) If Static IP is selected, please enter the IP Address and Subnet Mask given by your ISP. Then click Next. | Quick Setup - Static IP | Note After the rebooting, please reconnect to the network according to Step 4 Reconfigure PC and Step 5 Reconnect to Network. If Wireless Security is enabled, you need to enter the password you've just set to sucessfully finish the The Quick Setup is preparing to set up your connection type of WAR port. Repeater Mode connecting. IP Address: 0.00.0 O) PPPoE - For this connection, your will need your account name and password from your ISP. Subnet Mask: 0.0.0.0 (© Dynamic IP - Your ISP uses a DHCP service to assign your Router an IP address when connecting to the Internet. © Static IP - This type of connection uses a permanent, fixed (static) IP address that your ISP assigned. Default Gateway: (Optional) Primary DNS: (Optional) = Се] Secondary DNS: (Optional) [e 7 @ Click Survey button to find the available wireless €) Select the SSID of the target network and click Connect. €) The target network's SSID will be automatically filled into @ Click Reboot to reboot the Router and make the settings networks. Quick Setup - Wireless Repeater | for ecample:00-1 D-0F-11-22-33 Region: United States es Incorrect settings may cause interference (Р Disable Security + Security Options: WEP Key Index: 1 Authentication Type: Open System PassWord: | 4 Reconfigure PC Follow the steps in 1 Configure PC to set the IP address. Select Obtain an IP address automatically and Obtain DNS server address automatically. Click OK to finish the settings. Internet Protocol Version 4 (TCP/IPv4) Properties General | Alternat: j es can getIP i i ically if your | thig capability. Otherwise, you need to ask your network administrator for the appropriate IP settings. (© Use the following IP address: IP address: Subnet mask: Default gateway: (8) Obtain DNS server address automatically (© Use the following DNS server addresses: Preferred DNS server: Alternate DMS server: Validate settings upon exit the wireless setting figure. Select the Security Options and enter the Password. Then click Next. take effect. Quick Setup - Finish please click other menus if necessary. Congratulations! The Router is how connecting you to the Internet. For detail settings, The change of wireless config will not take effect until the Router reboot. Back | Reboot | eV ME Quick Setup - Wireless Repeater AP Count 10 SSID: [TP-Link_EBBESB | MAC of AP: 94-0C-6D-EB-BE-58 | forexample:00-1C-0F-11-22-33 _EDU Region: United States H States a Warning: E lect -LINK_EBBESB Incorrect settings may cause interference. LINK -LINK_BF13CE (Please choose Main AP*s type of encryption and input the wireless password) LINK_BF142C CUNK 020484 ity Opt Disable Security м _LINK_2BF75E WEP Key Index: 1 -LINK_PocketaP_419A88 duthenficatipnlTvpe: Open System Password: | — Note 5 Reconnect to Network Appendix: Troubleshooting After the rebooting, please reconnect to the network according to Step 4 Reconfigure PC and Step 5 Reconnect to Network. If Wireless Security is enabled, you need to enter the password you've just set to sucessfully finish the connecting. Only for four modes: AP, Router, Repeater and Bridge. In Repeater Mode, the SSID of TL-WR700N is the SSID of router that you want to access. Click refresh button, and then select the network SSID which is set in Step 3 Configure Router. Click Connect. factory default settings? TP-LINK Network No Internet access WPS000051e32c „All O ChinaNet-uWLC a Open Network and Sharing Center factory default settings? If Wireless Security is enabled, you need to enter the Security key you've set in Step 3 Configure Router. @ Whatcan | do if! forgot my password? 1) Restore the Router’s configuration to its factory default settings. If you don't know how to do that, please refer to How can | restore my Router's configuration to its Currently connected to: 7 2) To log in the Web Management page, use the default user name and password: admin, admin. Wireless Network Connection 2 ^ |Е To connect to the Wireless Network, use the default TP-LINK Network AM password on the label. TP-LINK_2046F2 „AM E CER EZ 3) Try to configure your Router once again by following | НН the instructions in th i t fthe QIG UK a я e instructions in the previous steps of the . Li apple_lee asii TP-LINK 656D4E ll How can | restore my Router's configuration to its With the Router powered on, use a pin to press and hold the Reset button for about 5 seconds before releasing it. For more troubleshooting help, go to www.tp-link.com/support/faq.asp f following details: Global Tel: +86 755 26504400 E-mail : supportetp-link.com Service time: 24hrs, 7 days a week Singapore Tel: +65 62840493 E-mail: [email protected] Service time: 24hrs, 7 days a week Tel: +44 (0) 845 147 0017 E-mail: [email protected] Service time: 24hrs, 7 days a week USA/Canada Toll Free: +1 866 225 8139 E-mail: [email protected] Service time: 24hrs,7 days a week Malaysia Tel: 1300 88 875465 (1300 88TPLINK) E-mail: [email protected] Click OK. y Connect to a Network [mE] O Type the network security key Reset Security key: [Y] Hide characters Note Guide in the Resource CD. Service time: 24 hrs a day, 7 days a week Switzerland Tel: +41 (0)848 800998 (German service) For more advanced settings, please refer to the User E-mail: [email protected] Fee: 4-8 Rp/min, depending on rate of different time Service time: Monday to Friday www.tp-link.c pport, sp For all other technical support, please contact us by using the Technical Support To download the latest Firmware, Driver, Utility and User Guide, go to Il 1 A a Australia & New Zealand Tel: AU 1300 87 5465 NZ 0800 87 5465 E-mail: [email protected] Service time: 24hrs, 7 days a week Turkey Tel: 444 1925 (Turkish Service) E-mail: [email protected] Service time: 9:00 AM to 6:00 PM, 7 days a week Italy Tel: +39 02 66987799 E-mail: [email protected] Service time: 9:00 AM to 6:00 PM, Monday to Friday na Tel: (+62) 021 6259 135 E-mail: support.idetp-link.com Service time: Monday to Friday 9:00 -12:00 ; 13:00 -18:00 *Except public holidays Germany / Austria Tel :+49 1805 875465 (German Service) / +49 1805 TPLINK E-mail: [email protected] Fee: 0.14 EUR/min from the German fixed phone network and up to 0.42 EUR/min from mobile phone. Service Time: Monday to Friday 9:00 AM to 6:00 PM GMT+1 or GMT+2 9:00 AM to 6:00 PM. | DAN GMT+1 or GMT+2 (Daylight Saving Time in Germany) O (Daylight Saving Time) * Except bank holidays in Hesse J TP-LINK TECHNOLOGIES CO., LTD. www.tp-link.com ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- White
- Wi-Fi 4 (802.11n) 150 Mbit/s
- Fast Ethernet
- Ethernet WAN
- Ethernet LAN (RJ-45) ports: 1
- Quality of Service (QoS) support
Frequently asked questions
You can connect to the network by searching for the SSID named 'TP-LINK_xxxxxx' (the SSID is found on the device label) and entering the password found on the label. Make sure you enable the pre-encryption function in the device settings.
If you forget your password, you can restore the device to its factory default settings by holding the Reset button for five seconds. You can then log in to the web management page with the default username and password: admin, admin. You will then be able to configure the device again.
You can change the network name (SSID) and password in the web management page. Log in to the web management page, navigate to the wireless settings, and change the desired settings. Remember to reboot the router to apply the new settings.