Note Please use only wired network connections to configure the Router.
Turn off all of your network devices, including your computer, Modem and the
Router.
Connect the WAN port on your
Router to the Modem’s LAN port with an Ethernet cable.
Connect your computer to the
Port labeled 1~4 on the Router with an Ethernet cable.
Plug the provided Power
Adapter into the Power jack on the back of the Router and the other end to a standard electrical wall socket.
1
Turn on all of your network devices and then check to see if the LEDs of the
Router display normally as the digram below describes.
PWR: Solid light
SYS/WLAN: Flashing
LAN: Flashing or solid light if the corresponding port is connected
WAN: Flashing or solid light
Note If the LEDs display abnormally, please check to see if all the cable connectors (power adapter and Ethernet cable) are well connected to your device.
Note To configure the device, you can either run the Resource CD (method one), or run the Web-based Quick Setup Wizard (method two). TP-LINK strongly recommends that you run the Resource CD.
2
Insert the provided Resource CD into your CD-ROM drive.
The Easy Setup Assistant will automatically prompt you on your computer’s screen.
Please select your product model and click
Easy Setup Assistant
Click START, and then follow the step-by-step instructions until you complete the configuration
The configuration has now been completed. Please skip to step 3 Testing the
Internet Connection.
3
Login
Open your web browser, type
http://tplinklogin.net in the address field and press Enter
A dialog box will prompt you for the User name and Password.
Enter the default values and click
OK.
User name: admin
Password: admin
Click OK
Note If the dialog box does not pop up, please refer to T3 in the
Troubleshooting guide. T2 will help you if you forget the password.
The web management page will display after a successful login.
Click Quick Setup
4
Internet Parameters Configuration
This page will then display.
Click Next
Select
Click Next
Wait for the Router to detect the connection type.
If PPPoE is detected, the screen will pop up as shown in A. Please proceed to AǗ
If Static IP is detected, the screen will pop up as shown in B. Please skip to BǗ
If Dynamic IP is detected, the screen will pop up as shown in C. Please skip to C.
Note detection.
1. Make sure the cable is securely plugged into the WAN port before
2. If the connection type your ISP provided is PPTP, L2TP or BigPond (or
Heart Beat Signal), you must go to “Network > WAN” to configure your connection type manually.
A
Configuration for PPPoE
This page will then display.
Enter the Username and
Password provided by your ISP
Click Next
After completing the above configuration, please skip to
Configuration.
Wireless Settings
5
B
Configuration for Static IP
Enter the IP Address,
Gateway, DNS provided by your ISP manually
Click Next
After completing the above configuration, please proceed to
Configuration.
C
Configuration for Dynamic IP
This page will then display.
If you are visiting the Router from the main computer, please select Yes
Click Clone MAC Address
Click Next
Wireless Settings or
If you are visiting the Router from another computer, rather than the main computer, please select No
Enter the main computer’s MAC in the field WAN MAC Address
Click Next
Note 1. It’s strongly recommended that you visit and configure the Router from the main computer.
2. To find the main computer’s MAC, please go to Start > Run on your main computer, type in cmd and press Enter. At the command prompt, enter
ipconfig/all and press Enter. The MAC will be displayed under Physical
Address.
6
After completing the above configuration, please proceed to Wireless Settings
Configuration.
Wireless Settings Configuration
This page will then display.
Keep the default setting:
Enable Wireless. If you want to disable wireless, please select Disable
Create a unique and easy-to-remember name for your wireless network.
You can also keep default settings without the device being affected.
Select your region from the drop-down list
Click Next
Note The wireless security has not yet been configured in the above steps. You are suggested to finish this configuration first and then refer to Appendix
Wireless Security Setup to configure the wireless security.
Click Finish
Or if wireless settings have been changed
Click Reboot
7
The basic settings for your Router are completed. Please open the web browser and log on to the following websites: http://www.tp-link.com http://www.google.com
If the above websites can be accessed, it indicates that your Router has been configured successfully and you can begin to enjoy the Internet. If the website cannot be accessed, please refer to “T4. What can I do if I cannot access the
Internet?” in the Troubleshooting guide.
Note
For advanced configurations, please refer to the User Guide on the
Resource CD provided.
Note The above configurations only need to be set once. If you want other computers in your network to access the Internet, please connect the desired computer to the router directly. If the additional computer can not access the
Internet, please set that computer referring to “T3. What can I do if I cannot
access the web-based configuration page?” in the Troubleshooting guide.
8
T1. How do I restore my Router’s configuration to its factory default settings?
With the Router powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before releasing it.
POWER RESET WAN 1 2 3 4
Hold it for 8 to 10 seconds
Note Once the Router is reset, the current configuration settings will be lost and you will need to re-configure the router.
T2. What can I do if I don’t know or forget my password?
1) Restore the Router’s configuration to its factory default settings. If you don’t know how to do that, please refer to section T1.
2) Use the default user name and password: admin, admin.
3) Try to configure your Router once again by following the instructions in the previous steps of the QIG.
T3. What can I do if I cannot access the web-based configuration page?
1) Configure your computer’s IP Address.
For Windows XP OS
Go to Start > Control Panel, you will then see the following page.
Click Network and Internet
Connections
9
Click Network
Connections
Right-click Local
Area Connection
Click Properties
Double-click Internet
Protocol (TCP/IP)
10
Select Obtain an IP address automatically
Select Obtain DNS server address
automatically
Click OK
Click OK
11
For Windows Vista OS
Go to Start > Settings >
Control Panel, and then you will see the following page.
Click View network status and tasks
Click View status
Click Properties
12
Double-click Internet Protocol
Version 4 (TCP/IPv4)
Select Obtain an IP address automatically
Select Obtain DNS server address automatically
Click OK
13
For Windows 7 OS
Go to Start > Settings >
Control Panel, and then you will see the following page.
Click View network status and tasks
Click Change adapter settings
Right-click Local
Area Connection
Click Properties
14
Double-click Internet Protocol
Version 4 (TCP/IPv4)
Select Obtain an IP address automatically
Select Obtain DNS server address automatically
Click OK
15
2) Configure your IE browser
Open your IE browser, click
Tools tab and you will see the following screen.
Click Internet Options
Select Never dial a connection
Click OK
Now, try to log on to the Web-based configuration page again after the above settings have been configured. If you still cannot access the configuration page, please restore your Router’s factory default settings and reconfigure your Router following the instructions of this QIG. Please feel free to contact our Technical
Support if the problem persists.
T4. What can I do if I cannot access the Internet?
1) Check to see if all the connectors are connected well, including the telephone line (for your modem), Ethernet cables and power adapter.
2) Disconnect the Router and directly connect your computer to the Modem and try to access the Internet. If you still cannot access the Internet, please contact
16
your ISP or the Modem’s manufacturer; otherwise, please reconnect the physical connection between your Modem, Router and the computer, then continue to follow the next step.
3) Make sure that you are connected to the TP-LINK Router with the computer that was originally connected to your modem, then login to the web-based management page and browse to “Network > MAC Clone”, click “Clone
MAC Address” and then click “Save”. Reboot the Router and try to access the Internet from your computer, if the problem persists, please go to the next step.
4) Please feel free to contact our Technical Support if the problem persists.
17
Log on to the Web Management
Page and click Wireless.
Select Wireless Security
Select WPA2-PSK-Personal
(Recommended)
Enter a Security Key using 8 characters or more (numbers or letters) in the PSK Password filed
Click Save
Click System Tools
Click Reboot
Click Reboot
18
Technical Support
For more troubleshooting help, go to: www.tp-link.com/support/faq.asp
To download the latest Firmware, Driver, Utility and User Guide, go to: www.tp-link.com/support/download.asp
For all other technical support, please contact us by using the following details:
Global
Tel: +86 755 26504400
E-mail: [email protected]
Service time: 24hrs, 7 days a week
Singapore
Tel: +65 62840493
E-mail: [email protected]
Service time: 24hrs, 7 days a week
UK
Tel: +44 (0) 845 147 0017
E-mail: [email protected]
Service time: 24hrs, 7 days a week
USA/Canada
Toll Free: +1 866 225 8139
E-mail: [email protected]
Service time: 24hrs, 7 days a week
Malaysia
Tel: 1300 88 875465 (1300 88TPLINK)
Email: [email protected]
Service time: 24hrs, 7 days a week
Russian Federation
Tel: 8 (495) 223-55-60
8 (800) 250-55-60 (toll-free call from any RF region)
E-mail: [email protected]
Service time: From 10:00 to 18:00
(Moscow time)
*Except weekends and holidays in
Russian Federation
Germany / Austria
Tel: +49 1805 875465 (German Service)
+49 1805 TPLINK
E-mail: [email protected]
Fee: 0.14 EUR/min from the German fixed phone network and up to 0.42
EUR/min from mobile phone
Service time: Monday to Friday 9:00 AM to 6:00 PM. GMT+ 1 or GMT+ 2
(Daylight Saving Time in Germany)
*Except bank holidays in Hesse
Australia & New Zealand
Tel: AU 1300 87 5465
NZ 0800 87 5465
E-mail: [email protected]
Service time: 24hrs, 7 days a week
Turkey
Tel: 444 19 25DŽTurkish ServiceDž
E-mail: [email protected]
Service time: 9:00 AM to 6:00 PM
7 days a week
Italy
Tel: +39 02 66987799
E-mail: [email protected]
Service time: Monday to Friday
9:00 AM to 6:00 PM
Ukrainian
Tel: +380 (44) 590-51-14
E-mail: [email protected]
Service time: Monday to Friday
14:00 PM to 22:00 PM
Brazilian(Portuguese Service)
Toll Free: 0800-770-4337
E-mail: [email protected]
Service time: Monday to Saturday
08:00 AM to 08:00 PM
Indonesia
Tel: (+62 ) 021 6259 135
E-mail : [email protected]
Service time : Monday to Friday
9:00 -12:00; 13:00 -18:00
*Except public holidays
Switzerland
Tel: +41 (0)848 800998 (German Service)
E-mail: [email protected]
Fee: 4-8 Rp/min, depending on rate of different time
Service time: Monday to Friday 9:00 AM to
6:00 PM. GMT+ 1 or GMT+ 2
(Daylight Saving Time)
