Trane Indirect Fired Make-Up Air Catalogue

Trane Indirect Fired Make-Up Air Catalogue
Indoor Gas-Fired
Make-Up Air Handlers
Standard and High Efficiency
Packaged Unit for Heating, Cooling,
Ventilating and Make-Up Air Applications
June 2003
MUA-D-3
Features
and
Benefits
General
Control Options
The Trane indoor make-up air handler
product line is a packaged air, heating
and cooling system, suitable for
heating, cooling, ventilating and
make-up air applications. These units
are designed for indoor use only. Unit
sizes range from 900 to 9,800 cfm
(0.4-4.6 cu m/s) with 1/2 to 15 hp motor
capabilities. These units are available
with inputs from 100,000 Btu/h to
1,200,000 Btu/h (29.3 to 351.4 kW).
In addition to a versatile offering of
mechanical features, this new unit also
offers a wide variety of factory installed
control options. Control components
are located in the main electrical
cabinet. The main electrical cabinet is
located out of the airstream as part of
the blower transition, between the
blower cabinet and the first furnace for
both standard and high cfm units. The
standard electrical control scheme
consists of a solid-state fan time delay,
two pre-wired relay sockets for fan on
and damper open functions mounted
on the unit’s main connection board, a
solid stage gas ignition system and
room or duct thermostats. The units are
also equipped with a blower door
safety interlock, a 24 VAC circuit
breaker, a high temperature limit switch
in each furnace section and a reverse
airflow switch located in the blower
cabinet as standard equipment.
Duct furnaces are AGA and CGA
certified for safety and performance
with a range of 100,000 Btu/h input to
400,000 Btu/h (29.3 to 117.1 kW) input
per duct furnace. The units can be
ordered as heating only, heating with
evaporative cooling or packaged
heating and cooling systems.
The mechanical configuration is
determined by selecting one of the four
standard arrangements. Arrangements
are divided into two classifications –
standard and high cfm blower types.
The standard blower unit consists of a
blower cabinet that houses dampers,
filters and blower in one cabinet. An
optional evaporative cooling unit is
available on units up to 800 MBh
(234.3 kW). Trane recommends the use
of 409 stainless steel whenever
evaporative cooling is installed
upstream of a duct furnace section(s).
The high cfm blower unit utilizes a
separate damper/filter cabinet with a
“V” bank filter arrangement, a blower
cabinet and up to three duct furnaces
(1200 MBh) (351.4 kW). An optional
cooling coil cabinet is offered on units
up to 800 MBh. Trane recommends the
use of 409 stainless steel whenever a
coil is used upstream of a furnace
section(s). Both standard and high cfm
blower arrangements may also include
outside air and/or return air.
All units are completely packaged, railmounted, wired, piped and test fired to
assure a smooth installation and easy
start-up.
All furnaces have optional left or right
hand access. The maximum discharge
air temperature for all duct furnaces is
150 F (66 C).
©2003 American Standard Inc.
2
Gas control options range from single
stage to six stages of fire, mechanical
or electronic modulation and direct
digital control (DDC). Air control
options offer a similar range of control
features from manual dampers to
modulating dampers that may include
mixed air, dry bulb, pressure sensing,
enthalpy control, DDC interface or
ASHRAE cycle control arrangements.
Units are available in a standard or
high efficiency line. The high efficiency
line features an integral flue vent fan
and sealed flue collector for improved
combustion. It reduces air
requirements and wind effects on the
system’s efficiency. Intermittent pilot
ignition reduces pilot gas losses and
the flue vent fan allows for horizontal
venting through side walls.
Contents
Features and Benefits
• AGA and CGA certified duct furnaces
• FM (Factory Mutual) Compliant
• Heating capacities from 100 MBh to
1200 MBh (29.3 kW- 351.4 kW)
• Gravity and power vented furnaces
• Cfm ranges from 900 to 9800 cfm
(0.4-4.6 cu. m/s)
• Motor sizes up to 15 horsepower
• ODP motors with high efficiency and
totally enclosed options
• Left hand or right hand service access
• Draw-thru coil cabinet with stainless
steel drain pan
• Evaporative cooling with standard 8 or
optional 12” media (203 or 305 mm)
• Standard 18-gauge cabinets
• Standard 20-gauge aluminized steel
heat exchanger
• Standard one-inch washable filters
• Standard single stage combination gas
valve
• Standard high temperature limit (each
furnace)
• Standard blower door safety interlock
switch
• Standard reverse airflow safety switch
• Standard 24-volt circuit breaker
• Standard printed circuit main
connection board
• Wiring harnesses with stamped wire
numbers
• Solid stage automatic pilot ignition
control
• Solid-state fan time delay
• Over 40 standard gas and air control
Features and Benefits
2
Model Number Description
4
Unit Configurations
6
General Data
10
Application Considerations
12
Selection Procedure
14
packages
Performance Adjustment Factors 19
3
Performance Data
20
Electrical Data
37
Controls
38
Dimensional Data
41
Weights
66
Options
68
Features Summary
71
Mechanical Specifications
72
Model
Number
Description
Digit 1 — Gas Heating Equipment
G = Gas
Digit 2 — Unit Type
S = Indoor Make-Up Air Handler
G = High Efficiency Indoor Make-Up Air
Handler
D = Indoor Duct Furnace
L = High Efficiency Indoor Duct Furnace
Digit 3 — Furnace Type
A = Standard Temp Rise (30-80 F) LH
B = Standard Temp Rise (30-80 F) RH
S = Special Furnace Type
Note: LH = Left Hand RH = Right Hand
Digit 4 — Development Sequence
A = First Generation
Digits 5 and 6 — Input Capacity
Single Furnace
10 = 100 MBh Input
15 = 150 MBh Input
20 = 200 MBh Input
25 = 250 MBh Input
30 = 300 MBh Input
35 = 350 MBh Input
40 = 400 MBh Input
Double Furnace
50 = 500 MBh Input
60 = 600 MBh Input
70 = 700 MBh Input
80 = 800 MBh Input
Triple Furnace
12 = 1200 MBh Input
SS = Special unit
Digit 7 — Venting Type
G = Gravity Venting (All GS Units)
P = Power Venting (All GG Units)
S = Special Venting
Digit 8 — Main Power Supply
A = 115/60/1
B = 208/60/1
C = 230/60/1
D = 208/60/3
E = 230/60/3
F = 460/60/3
G = 575/60/3
S = Special Main Power Supply
G
S A A
40 G D C
1
2
5,6 7
3
4
8
D0
2
B Q
1
0
1
A
0
+
9 10,11 12 13 14 15 16 17 18 19 20 21
Digit 9 — Gas Control Option
(Intermittent Pilot Ignition)
A = Single-Stage
B = Two-Stage
C = Hydraulic Modulating (60-100)
D = Hydraulic Modulating (75-200)
E = Hydraulic Modulating w/Bypass and
limit (60-100)
F = Hydraulic Modulating w/Bypass
(75-200)
G = Electronic Modulating w/Room T-Stat
H = Electronic Modulating w/Duct T-Stat
J = Electronic Modulating w/Duct T-Stat
and Override Room Thermostat
K = Electronic Modulating w/External
4-20 mA Input (Furnace 1)
L = Electronic Modulating w/External
4-20 mA Input (All furnaces)
M= Electronic Modulating w/External
0-10 VDC Input (Furnace 1)
N = Electronic Modulating w/External
0-10 VDC Input (All furnaces)
P = VAV Control Two-Stage
R = VAV Control Three-Stage
T = VAV Control Four-Stage
U = S-350 2-Stage Modular Electronic
Control System
W= S-350 3-Stage Modular Electronic
Control System
X = S-350 4-Stage Modular Electronic
Control System
Y = S-350 6-Stage Modular Electronic
Control System
S = Special Gas Control
Digit 10, 11 — Design Sequence
D0 = Design Sequence
Digit 12 — Fuel Type
N = Natural Gas
P = LP Gas (Propane)
L = Natural Gas with 100% Lockout
S = Special Fuel type
4
N
Digit 13 — Heat Exchanger Material
1 = Aluminized Steel
2 = #409 Stainless Steel (First Furnace Only)
3 = #409 Stainless Steel (All Furnace
Sections)
4 = #321 Stainless Steel (First Furnace Only)
5 = #321 Stainless Steel (All Furnace
Sections)
6 = #409 Stainless Steel Package
(First Furnace Only)
7 = #409 Stainless Steel Package
(All Furnace Sections)
8 = #321 Stainless Steel Package
(First Furnace Only)
9 = #321 Stainless Steel Package
(All Furnace Sections)
S = Special Heat Exchanger Package
Digit 14 — Indoor Arrangements
A = Indoor Duct Furnace
B = Blower (Standard)
D = Blower (Standard) Evaporative Cooler
G = Blower (High CFM)
K = Blower (High CFM) /Cooling
S = Special Rooftop Arrangement
Digit 15 — Indoor Heating Unit Motor
Selection
0 = No Motor (Duct Furnace)
A = 1/2 HP w/Contactor
B = 3/4 HP w/Contactor
C = 1 HP w/Contactor
D = 1 1/2 HP w/Contactor
E = 2 HP w/Contactor
F = 3 HP w/Contactor
G = 5 HP w/Contactor
H = 1/2 HP w/Magnetic Starter
J = 3/4 HP w/Magnetic Starter
K = 1 HP w/Magnetic Starter
L = 1 1/2 HP w/Magnetic Starter
N = 2 HP w/Magnetic Starter
P = 3 HP w/Magnetic Starter
Q = 5 HP w/Magnetic Starter
R = 7 1/2 HP w/Magnetic Starter
T = 10 HP w/Magnetic Starter
U = 15 HP w/Magnetic Starter
S = Special Motor
Model
Number
Description
Digit 16 — Motor Speed
0 = No Motor (Duct Furnace)
1 = Single Speed ODP 1800 RPM
2 = Single Speed TEFC 1800 RPM
3 = Single Speed High Efficiency ODP
1800 RPM
4 = Single Speed High Efficiency TEFC
1800 RPM
5 = 2S1W ODP 1800/900 RPM
6 = 2S2W ODP 1800/1200 RPM
S = Special Motor Speed and Starter
Digit 17 — Coil Options
0 = No cooling Coil selection
A = DX Coil, 4-Row, Single Circuit
B = DX Coil, 4-Row, Dual Circuit
C = DX Coil, 6-Row, Single Circuit
D = DX Coil, 6-Row, Dual Circuit
E = Chilled Water Coil, 4-Row,
G = Chilled Water Coil, 6-Row,
S = Special Coil
Digit 18 — Air Inlet Configuration
0 = None (Indoor Duct Furnace)
1 = Outside Air (OA) Horizontal Inlet
3 = Return Air (RA) Bottom Inlet
4 = Outside and Return Air (OA/RA)
S = Special Air Inlet Configuration
Digit 19 — Air Control and
Damper Arrangement
0 = None
A = Outside Air 2 Pos. Motor/SR
B = Return Air 2 Pos. Motor/SR
C = OA/RA 2 Pos SR
E = OA/RA Mod Mtr w/Mixed Air Control/
Min Pot/SR
H = OA/RA Mod Mtr w/Mixed Air Control/
SR
K = OA/RA Mod Mtr w/Min Pot/SR
M = OA/RA Mod Mtr w/Dry Bulb/Mixed Air
Control/Min Pot/SR
N = OA/RA Mod Mtr w/Enthalpy Controlled
Economizer/SR
P = OA/RA Mod Mtr w/Space Pressure
Controller
R = OA/RA Mod Mtr w/S-350 P
Proportional Mixed Air Control/SR
U = OA/RA Mtr. w/External 0-10 VDC and
4-20 mA Analog Input/SR
(External Input)
W = ASHRAE Cycle I (OA/RA 2 Pos.
w/Warm-up Stat/SR
X = ASHRAE Cycle II (OA/RA Mod
w/Warm-up Stat/Mixed Air/min pot/SR
Y = ASHRAE Cycle III (OA/RA Mod.
w/Warm-up Stat/Mixed Air/SR
Z = Manual Dampers
S = Special Air Control and
Damper Arrangement
5
Digit 20
0 = Non-California Shipment
1 = California Shipment
Digit 21 — Miscellaneous Options
A = Orifices for Elevation Above 2000 Feet
(Specify Elevation)
B = 12” Evaporative Media (Celdek)
D = Horizontal Return
E = Interlock Relay – 24V Coil DPDT 10A
F = Freezestat
G = Fan Time Delay (Indoor Duct Furnace)
H = Return Air Firestat
J = Supply Air Firestat
K = Manual Blower Switch
L = 409 Stainless Steel Furnace Drip Pan
M = Double Wall Construction
P = Low Leak Dampers
Q = Clogged Filter Switch
R = High/Low Gas Pressure Limit Switches
T = Status Indicator Lamps (Elec Cabinet)
V = Manual Reset High Limit Switch
W = Interlock Relay —24/115V Coil SPDT
10A
X = Interlock Relay —24/115-230V Coil
DPDT 10A
Y = Ambient Lockout
Z = 8” Evaporative Media (Glasdek)
1 = 12” Evaporative Media (Glasdek)
2 = Hinged Service Access Doors
Unit
Configurations
Indoor Make-Up Air Handler
Gravity Vented
Unit Type
Standard Features
Arrangement A
Indoor Gas Duct Furnace
- Natural or LP (Propane Gas)
- Single Stage 24 Volt Gas Valve
- Intermittent Pilot Ignition
- Orificed for Operation Up to 2000' Above Sea Level
- Aluminized Steel Heat Exchanger
- 24 Volt High Temperature Safety Circuit
- 24 Volt Control Circuitry
- Blow-thru Applications Only
Arrangement B
Indoor Heating Unit with Standard Blower
- Natural or LP (Propane Gas)
- Single Stage 24 Volt Gas Valve
- Intermittent Pilot Ignition
- Orificed for Operation Up to 2000' Above Sea Level
- Aluminized Steel Heat Exchanger
- 24 Volt High Temperature Safety Circuit
- Terminal Block Wiring, Single Point Connection
- Quick Opening Access Doors (Blower Section)
- Single, Forward Curved Blower
- Insulated Blower/Filter/Damper Cabinet
- 1” Permanent Filters
- Fan Time Delay Relay
- Electrical Cabinet Isolated from the Airstream
- 24 Volt Control Circuitry
- Low Voltage Circuit Breaker
- Blower Door Interlock Switch with Service Override
Arrangement D
Indoor Heating Unit with Standard Blower
and Evaporative Cooler
Same as Arrangement B with
- Evaporative Cooler
- High Efficiency 8“ Media
- Self Cleaning Design
- Sealed Pump Motor with Float Valve
- 24 Volt Control Circuitry
- Heavy Duty Stainless Steel Water Tank
- Easy Access Intake Filter and PVC Distribution Tubes
6
Unit
Configurations
Indoor Make-Up Air Handler
Gravity Vented
Unit Type
Standard Features
Arrangement G
Indoor Heating Unit with High Cfm Blower
- Natural or LP (Propane Gas)
- Single Stage 24 Volt Gas Valve
- Intermittent Pilot Ignition
- Orificed for Operation Up to 2000' Above Sea Level
- Aluminized Steel Heat Exchanger
- Electrical Cabinet Isolated from the Airstream
- 24 Volt High Temperature Safety Circuit
- Terminal Block Wiring, Single Point Connection
- Quick Opening Access Doors (Blower Section)
- 1 Permanent Filters
- Fan Time Delay Relay
- Standard V-bank Filter and Damper Cabinet
- Insulated Filter/Damper and Blower Cabinet
- Single Forward Curved Blower
- 24 Volt Control Circuitry
- Low Voltage Circuit Breaker
- Blower Door Interlock Switch with Service Override
Arrangement K
Indoor Heating Unit with High Cfm Blower
and Cooling Coil Section
Same as Arrangement G with
- Coil Section
- Mounting for 4 to 6 Row Coils – Single or Dual Circuit
- Stainless Steel Drain Pan with 3/4” Tapped Outlets
Motors/air inlet configuration/air control and damper arrangement must be selected and added to the list price of each unit.
NOTES:
1. Arrangements are shown with the maximum number of furnaces available.
2. Legend is as follows:
B/F/D - Standard Blower/Filter/Damper
SP - Supply Plenum
EV - Evaporative Cooler
F/D - Filter/Damper
B - High Cfm Blower
CC - Cooling Coil
3. Horizontal outside air over return air. Specify air inlet Configuration 4 and then
select miscellaneous Option D for horizontal return.
Air Inlet Configuration
1
3
4
See Note 3 Above
7
Unit
Configurations
High Efficiency Indoor Make-Up Air Handler
Power Vented
Unit Type
Standard Features
Arrangement A
High Efficiency Indoor Gas Duct Furnace
- Natural or LP (Propane Gas)
- Single Stage 24 Volt Gas Valve
- Intermittent Pilot Ignition
- Orificed for Operation Up to 2000' Above Sea Level
- Aluminized Steel Heat Exchanger
- 24 Volt High Temperature Safety Circuit
- 24 Volt Control Circuitry
- Factory Installed Flue Vent Fan
- Sealed Draft Diverter
- Blow-thru Applications Only
Arrangement B
High Efficiency Indoor Heating Unit
with Standard Blower
- Natural or LP (Propane Gas)
- Single Stage 24 Volt Gas Valve
- Intermittent Pilot Ignition
- Orificed for Operation Up to 2000' Above Sea Level
- Aluminized Steel Heat Exchanger
- 24 Volt High Temperature Safety Circuit
- Terminal Block Wiring, Single Point Connection
- Quick Opening Access Doors (Blower Section)
- Single, Forward Curved Blower
- Insulated Blower/Filter/Damper Cabinet
- 1” Permanent Filters
- Fan Time Delay Relay
- Electrical Cabinet Isolated from the Airstream
- 24 Volt Control Circuitry
- Low Voltage Circuit Breaker
- Blower Door Interlock Switch with Service Override
- Factory Installed Flue Vent Fan - Sealed Draft Diverter
Arrangement D
High Efficiency Indoor Heating Unit
with Standard Blower and Evaporative Cooler
Same as Arrangement B with
- Evaporative Cooler
- High Efficiency 8“ Media
- Self Cleaning Design
- Sealed Pump Motor with Float Valve
- 24 Volt Control Circuitry
- Heavy Duty Stainless Steel Water Tank
- Easy Access Intake Filter and PVC Distribution Tubes
8
Unit
Configurations
High Efficiency Indoor Make-Up Air Handler
Power Vented
Unit Type
Standard Features
Arrangement G
High Efficiency Indoor Heating Unit
with High Cfm Blower
- Natural or LP (Propane Gas)
- Single Stage 24 Volt Gas Valve
- Intermittent Pilot Ignition
- Orificed for Operation Up to 2000' Above Sea Level
- Aluminized Steel Heat Exchanger
- Electrical Cabinet Insulated from the Airstream
- 24 Volt High Temperature Safety Circuit
- Terminal Block Wiring, Single Point Connection
- Quick Opening Access Doors (Blower Section)
- 1 Permanent Filters
- Fan Time Delay Relay
- Standard V-bank Filter and Damper Cabinet
- Insulated Filter/Damper and Blower Cabinet
- Single Forward Curved Blower
- 24 Volt Control Circuitry
- Low Voltage Circuit Breaker
- Blower Door Interlock Switch with Service Override
- Factory Installed Flue Vent Fan
- Sealed Draft Diverter
Arrangement K
Indoor Heating Unit with High Cfm Blower
and Cooling Coil Section
Same as Arrangement G with
- Coil Section
- Mounting for 4 to 6 Row Coils – Single or Dual Circuit
- Stainless Steel Drain Pan with 3/4” Tapped Outlet
Motors/air inlet configuration/air control and damper arrangement must be selected and added to the list price of each unit.
NOTES:
1. Arrangements are shown with the maximum number of furnaces available.
2. Legend is as follows:
B/F/D - Standard Blower/Filter/Damper
SP - Supply Plenum
EV - Evaporative Cooler
F/D - Filter/Damper
B - High Cfm Blower
CC - Cooling Coil
3. Horizontal outside air over return air. Specify air inlet Configuration 4 and
then select miscellaneous Option D for horizontal return.
Air Inlet Configuration
1
3
4
See Note 3 Above
9
General
Data
Indoor Makeup Air Arrangement Reference
Furnace Type A, B
Temperature Rise 30 F-80 F
Standard Blower
Arrangements B
Standard Blower W/Evap.
Arrangements D
High CFM Blower
Arrangements G
High CFM Blower W/Cooling
Arrangements K* DX Coil
High CFM Blower W/Cooling
Arrangements K* Chilled Water Coil
Furnace Type A, B
Temperature Rise 60 F-160 F
Capacity 10-40
10 - 900-2,400 CFM, 1/2-3 HP
15 - 1,400-3,600 CFM, 1/2-5 HP
20 - 1,800-4,900 CFM, 1/2-5 HP
25 - 2,300-5,500 CFM, 1/2-5 HP
30 - 2,700-6,500 CFM, 3/4-5 HP
35 - 3,200-8,500 CFM, 3/4-5 HP
40 - 3,700-8,500 CFM, 3/4-5 HP
ESP .1-2” in WC
Capacity 10-40
10 - 900-2,400 CFM, 1/2-3 HP
15 - 1,400-3,600 CFM, 1/2-5 HP
20 - 1,800-4,900 CFM, 1/2-5 HP
25 - 2,300-5,500 CFM, 1/2-5 HP
30 - 2,700-6,500 CFM, 3/4-5 HP
35 - 3,200-8,500 CFM, 3/4-5 HP
40 - 3,700-8,500 CFM, 3/4-5 HP
ESP .1-2” in WC
Capacity 20-40
20 - 1,800-4,900 CFM, 1/2-5 HP
25 - 2,300-5,500 CFM, 1/2-7 1/2 HP
30 - 2,700-7,400 CFM, 1/2-7 1/2 HP
35 - 3,200-8,600 CFM, 1/2-10 HP
40 - 3,700-9,800 CFM, 1/2-10 HP
Capacity 60-80
50 - 2,300-5,200 CFM, 1/2-5 HP
60 - 2,700-6,000 CFM, 3/4-5 HP
70 - 3,200-7,500 CFM, 1/2-5 HP
80 - 3,700-7,500 CFM, 3/4-5 HP
ESP .1-2” in WC
Capacity 10-40
10 - 1,600-2,400 CFM, 1/2-5 HP
15 - 1,600-3,000 CFM, 1/2-5 HP
20 - 2,100-4,400 CFM, 1/2-5 HP
25 - 2,500-4,400 CFM, 1/2-5 HP
30 - 2,800-5,800 CFM, 3/4-7 1/2 HP
35 - 3,200-5,800 CFM, 3/4-7 1/2 HP
40 - 3,700-6,800 CFM, 3/4-7 1/2 HP
ESP .1-2” in WC
Capacity 10-40
10 - 960-2,400 CFM, 1/2-5 HP
15 - 1,400-2,900 CFM, 1/2-5 HP
20 - 1,800-4,300 CFM, 1/2-5 HP
25 - 2,300-4,300 CFM, 1/2-5 HP
30 - 2,700-5,700 CFM, 1/2-7 1/2 HP
35 - 3,200-5,700 CFM, 3/4-7 1/2 HP
40 - 3,700-6,300 CFM, 3/4-7 1/2 HP
ESP .1-2” in WC
ESP .1-2” in WC
Capacity 60-80
50 - 2,500-4,400 CFM, 1-5 HP
60 - 2,800-5,800 CFM, 3/4-7 1/2 HP
70 - 3,200-5,800 CFM, 3/4-7 1/2 HP
80 - 3,700-6,500 CFM, 3/4-7 1/2 HP
Furnace Type A, B
Temperature Rise 90 F-180 F
N/A
ESP .1-2” in WC
Capacity 60-80
50 - 2,300-5,200 CFM, 1/2-5 HP
60 - 2,700-6,000 CFM, 3/4-5 HP
70 - 3,200-7,500 CFM, 1/2-5 HP
80 - 3,700-7,500 CFM, 3/4-5 HP
ESP .1-2” in WC
Capacity 60-80
50 - 2,300-6,000 CFM, 1/2-10 HP
60 - 2,700-7,400 CFM, 1/2-10 HP
70 - 3,200-8,600 CFM, 1/2-10 HP
80 - 3,700-9,800 CFM, 3/4-15 HP
N/A
Capacity 12
12 - 4,500-9,800 CFM, 1-15 HP
ESP .1-2” in WC
Capacity 60-80
50 - 2,300-4,300 CFM, 1/2-5 HP
60 - 2,700-5,700 CFM, 3/4-7 1/2 HP
70 - 3,200-5,700 CFM, 3/4-7 1/2 HP
80 - 3,700-6,300 CFM, 3/4-7 1/2 HP
ESP .1-2” in WC
*The maximum CFM for Arrangements K is 6,500. A two-speed motor may be utilized for non-cooling air flow up to 9,800 cfm.
10
ESP .1-2” in WC
N/A
N/A
General
Data
Table G-1 — Filter Data
Rooftop
Arrangement
B-D
10,15
(4)16 x 20
20,25,50
(4)20 x 20
Unit Size
G-K
(8)16 x 20
(8)20 x 20
30,35,60,70
(4)16 x 20
(2)20 x 20
(8)16 x 20
(4)20 x 20
40,80,12
(6)20 x 20
(12)20 x 20
Table G-2 — Metric Conversion Table
Unless otherwise specified, the following conversions may be used for calculating SI unit measurements:
1 cubic foot= 0.028 m3
1 inch water column = 0.029 kPa
1 foot = 0.0305 m
1 gallon = 3.785 L
1 inch = 25.4 mm
1,000 Btu/Cu. Ft. = 37.5 MJ/m3
1 psig = 6.894 kPa
1 liter/second = CFM x 0.472
1 pound = 0.453 kg
1 meter/second = FPM ÷ 196.8
1,000 Btu per hour = 0.293 kW
11
Application
Considerations
Gas Heating Value
The majority of gas heating units are
installed in applications where natural
gas is readily available. In areas where
natural gas is not available, Trane units
may be ordered directly from the
factory for use on LP (propane) gas.
Gas heat content varies by fuel type
and location. The standard gross
heating value for natural gas is 1,000
Btuh per cubic foot; for propane it is
2,500 Btuh per cubic foot. Significant
variations from these standard values
should be taken into account in
equipment selections. To account for
variations in the gross heating value of
the fuel, adjust the total heat input
required and select the unit on the basis
of the adjusted load using the following
formula:
Adjusted load = Calculated load x
Standard gross heat value (Btuh/cu ft)
Actual gross heat value (Btuh/cu ft)
Low Temperature Rise
Trane recommends against the setup of
a unit which will result in a temperature
rise of less than 20 F. With such low
temperature rises, the flue gases
passing through the heat exchanger are
cooled to condensate before reaching
the flue outlet. This condensate is
corrosive and will result in shortened
heat exchanger life.
Air Density
Catalog performance data is based on
elevations up to 2,000 feet (610 m)
above sea level. Above 2,000 feet (610
m), the unit’s heating capacity must be
derated four percent for each 1,000 feet
(305 m) above sea level and special
orifice selections are required. Table
PAF-1 contains correction factors that
can be applied to the unit’s cataloged
heating capacity, fan rpm, and fan bhp
to obtain actual values for elevations
above 2,000 feet (610 m).
Corrosive Atmospheres
Corrosion of heat exchangers and draft
diverters have two basic variables —
moisture (condensation) and sulfur.
These two ingredients form to make
sulfuric acid in the combustion process.
Condensation occurs commonly in
make-up air systems, using large
amounts of fresh air, when air
temperatures entering the heat
exchanger drop to 40 F or below. This
reaction can also occur in recirculating
systems where some quantity of
outside air is introduced upstream
of the exchanger. The sulfur will always
be present as an integral component of
the gas. The resulting concentration of
the acid is governed by the amount of
sulfur in the gas. This concentration
varies from gas to gas and geographically
within the same type of gas.
Beyond sulfuric acid corrosion, there is
the area of chlorinated or halogenated
hydrocarbon vapor corrosion. This type
of corrosion occurs when substances
are mixed with combustion air that will
cause the formation of hydrochloric or
hydrofluoric acid when burned. These
basic substances are found in
degreasers, dry cleaning solvents,
glues, cements, paint removers and
aerosol propellants. Specific chemicals
included in this group are
trichloroethylene, perchloroethylene,
carbon tetrachloride, methylene
chloride, methyl chloroform and
refrigerants 11, 12, 21, 22 and 114.
If sufficient ppm content of these
corrosives is present, none of the
common heat exchanger materials will
hold up. The dilemma becomes whether
to place the gas heating equipment
outside of the area to be conditioned or
use equipment in the space which does
not burn a fuel such as gas (i.e., electric
or hydronic).
12
Units should not be installed in areas
with corrosive or inflammable
atmospheres. Locations containing
solvents or chlorinated hydrocarbons
will produce corrosive acids when
coming in contact with burner flames.
This reaction will greatly reduce the life
of the heat exchanger and may void
the warranty. For added protection
against heat exchanger corrosion,
optional 409 and 321 stainless steel
construction is available.
On units using outside air, with
entering air temperature below 40 F,
condensation of flue gas in the heat
exchanger is possible. In these cases,
stainless steel heat exchangers are
recommended. An optional 409 or 321
stainless steel heat exchanger is
recommended whenever there is an
evaporative cooler or cooling coil
upstream of the furnace section(s).
Careful review of the job application
with respect to use, probable
contaminants within a conditioned
space and the amount of fresh air to be
brought in will help to make the proper
selection of heat exchanger material.
This review will help to eliminate
problems before they begin.
Application
Considerations
FM and IRI Requirements
IRI, which stands for Industrial Risk
Insurers, and FM, which stands for
Factory Mutual, are both basically
insurance companies which insure
commercial/industrial firms against a
variety of losses. Both publish
requirements which must be met by
certain equipment operating in the
facilities they are preparing to insure.
Listed below is our interpretation of the
requirements of both insurers
pertaining to heating units only to the
extent of features/controls required by
IRI and/or FM. There are a number of
additional requirements which pertain
to electrical service, details of
installation, etc., and we urge you to
obtain copies of the publications
pertaining to these details if you are
involved in a job where IRI or FM
adherence has been indicated. The
requirements detailed herein are our
interpretations of the latest publications
in our possession and we must
disclaim any responsibility for errors
due to our interpretation and/or lack of
any updated revision of these
standards. Our intent is to provide you
with an understanding of the
application of these standards and how
we believe our indirect-fired gas
heating equipment applies.
IRI Requirements
1
All input sizes require 100 percent
shutoff. This requires that any natural
gas unit, equipped with intermittent
pilot ignition, must employ a “lock-out”
type ignition system which will shut off
pilot gas if the pilot fails to light at any
time. This system is required by AGA
on LP gas units as standard equipment.
However, for natural gas units, you will
need to specify fuel type “L” Natural
Gas with 100 percent lockout.
2
All units require AGA certification or UL
listed controls. Our units are AGA
certified and meet this requirement.
3
Models with inputs of 150,000 to
400,000 Btuh (43.9-117.1 kW) require
mechanical exhaust and a safety
interlock. For our units this means a
power vented unit.
FM Requirements
1
All units must be AGA certified or UL
listed. Our units are AGA certified.
2
The high limit control must be in a
circuit, the voltage of which does not
exceed 120 VAC. All of our high limits
would meet this requirement.
The specific requirement for an “IRI or
FM gas train,” while it applies to direct
and indirect-fired gas heating
equipment as well as oil-fired, comes
into play only with units having an
input in excess of 400,000 Btuh (117.1
kW). This may be one of the reasons
why the majority of gas heating
equipment manufacturers (indirectfired) limit their largest individual
furnace to 400,000 Btuh (117.1 kW).
Minimum/Maximum Gas
Inlet Pressures
Gas valves are suitable to a maximum
inlet pressure of 0.5 psi (14 inches water
column) (3.5 kPa) on natural gas. If the
main gas supply pressure is greater
than 14 inches WC (3.5 kPa), a step
down pressure regulator must be field
installed ahead of the gas valve.
Minimum inlet pressure for natural gas
units is 61/2 inches WC (1.6 kPa).
For LP (propane) gas, the minimum
inlet pressure is 111/2 inches WC (2.9
kPa) and the maximum inlet pressure is
14 inches WC (3.5 kPa).
High Pressure Regulators —
Natural Gas Only
The Trane gas heating products
contained in this catalog are designed
to operate at a pressure of 3.5-inch WC
(water column) (0.9 kPa) when firing on
natural gas. This is the “manifold”
pressure or that which is present at the
burner orifices. All five and six-function
valves provide a built-in pressure
regulator which is capable of reducing
“supply” pressures from a maximum
of 14-inch WC (3.5 kPa) (1/2 psi) down to
3.5-inch WC (0.9 kPa) on the leaving
side of the valve. The valve typically
drops about 11/2-inch (38 mm) so the
minimum supply pressure is 5-inch WC
(1.3 kPa).
Whenever supply pressures exceed
14-inch WC (3.5 kPa), a high pressure
regulator should be selected. We
supply an Equimeter regulator which is
fitted with pressure springs and
capacity orificing to meet the
requirements of each specific job. In
order to select the proper spring/orifice
combination, we need to know what
the supply pressure is on that
particular job and the input size of the
unit being ordered. More than one unit
can be run from one regulator;
however, we recommend that each
unit have its own regulator.
We require that the job supply pressure
be included on all jobs requiring high
pressure regulators along with the unit
size. The table that follows displays the
regulator’s range as it pertains to inlet
pressure and MBh. NA requires the
customer to contact a local utility or an
industrial supply house.
These devices are not available from
Trane for LP gas. LP accessories must
be secured from the gas supplier or
industrial supply house.
13
Selection
Procedure
Temperature Rise
Quick Sizer Chart 1
Furnace Type (A, B) Arrangement (B, D)
Airflow, CFM
Airflow, CFM
14
Selection
Procedure
Temperature Rise
Quick Sizer Chart 2
Furnace Type (A, B) Arrangement (G, K)
Airflow, CFM
Airflow, CFM
15
Selection
Procedure
Step 1
To properly select a unit, two of the
three following items must be known:
temperature rise (TR) required, cubic
feet per minute of air delivery (cfm)
required and output (Btu/h out)
required. From any two of these items
the third item can be determined, as
well as the input (Btu/h In) required, by
using the following:
Figure SP-1 — Zone Chart
TR = BTU/H Out ÷ (1.085 x CFM)
CFM = BTU/H ÷ (1.085 x TR)
BTU/H Out = (CFM x 1.085) x TR
BTU/H In = BTU/H Out ÷ Efficiency
.80 or .79
(The value 1.085 represents a constant.)
With any two of the three required
values, match these requirements to a
unit with the nearest input (Btu/h),
temperature rise (TR) and airflow (cfm)
capabilities keeping in mind that:
BTU/H Out = BTU/H In x Efficiency
Refer to the “Arrangement Reference”
to match a capacity range (Btu/h), air
delivery (cfm) and temperature rise (TR)
with a rooftop arrangement.
The top portion of Quick Sizer Charts 1
and 2 allows the use of temperature rise
and cfm to determine capacity, or
temperature rise and capacity to
determine cfm, or capacity and cfm to
determine temperature rise. Follow the
top chart down to the corresponding
filter and cooling range for the selection.
Step 2
Once capacity, temperature rise and
cfm have been determined, go to the
accessory pressure losses table for the
arrangement and calculate pressure
losses for unit accessories. Add the
losses for filters, plenums, dampers,
rainhood with screen or moisture
eliminators, evaporative cooler or
cooling coil and losses due to ductwork
to determine the total esp.
Step 3A – 2000 Ft. Altitude and Below
Refer to the performance table for the
selection and determine rpm and bhp
for the total external static pressure
(esp). Go to the table row that most
closely matches unit capacity,
temperature rise and cfm, and follow
the row out to the column that equals
the total esp for rpm and bhp values.
Step 3B – Above 2000 Ft. Altitude
To correct for altitude, go to Table
PAF-1, Correction Factors for Altitude.
From this table, determine the
correction factor from temperature and
altitude for the system.
Correct the esp from ductwork to
actual esp for altitude, then add sp
from accessories as shown below.
Refer to the performance table for the
selected unit. Go to the row that most
closely matches unit capacity,
temperature rise and cfm, and follow
the row out to the column that equals
the corrected actual esp for rpm and
bhp values. The bhp value cannot be
corrected to actual bhp for altitude as
shown below.
Performance
Evaporative cooling is most commonly
used in areas where the relative
humidity is low and the dry bulb
temperatures are high. However,
cooling through evaporation can be
used in most areas.
Evaporative cooling is best utilized
whenever the wet bulb depression
(difference between dry and wet bulb
temperature) is a minimum of 15 F.
Corrected BTUH Input =
Catalog BTUH Input ÷ Factor
The efficiency of the evaporative cooler
is determined by a variety of factors:
geographical location, application, air
change requirements, sufficient water
supply, airflow and maintenance. In
most instances, efficiency is expected to
be between 77 percent and 88 percent.
Heat gains in the distribution system
will affect the final output temperature.
Corrected BTUH Output =
Corrected BTUH Input x Efficiency
For SI metric conversion, see Table G-2
on page 11.
Actual ESP = Duct ESP x Factor +
Access. SP
Actual BHP = Cat. BHP ÷ Factor
16
Selection
Procedure
Figure SP-2 — Psychrometrics Chart
Use the psychrometric chart (shown in
Figure SP-2) or actual humidity
temperature readings to estimate the
leaving dry bulb temperature at the
outlet of the evaporative cooler.
Example:
Entering Dry Bulb: 95 F
Entering Wet Bulb: 75 F
Wet Bulb Depression (95 F - 75 F)
= 20 F
Effective Wet Bulb Depression
(20 F x .85) = 17 F
Leaving Dry Bulb Temperature
(95 F - 17 F) = 78 F
Leaving Wet Bulb = Entering Wet Bulb
= 75 F
Selection Method
The easiest method for selecting an
evaporative cooler is to first determine
the required number of air changes per
minute.
1
Using Figure SP-1, choose the
geographical zone in which the unit is
to be installed.
2
Determine the internal load within the
structure:
Normal Load: structures with normal
people loads, and without high internal
heat gains.
High Load: Structures with high
equipment loads (i.e., factories,
laundromats, beauty salons, restaurant
kitchens, etc.), and structures with high
occupancy (night clubs, arenas, etc.).
3
Determine whether the structure has
normal or high heat gains.
Normal Gain: Structures that have
insulated roofs or are in shaded areas.
Structures that have two or more
stories or facing directions with no sun.
High Gain: Structures that have
uninsulated roofs, unshaded areas, or
rooms that are exposed to sun.
4
Using Table SP-1, determine the
required air changes per minute based
on zone selection and the type of heat
load.
5
Finally, determine the air quantity for
the space chosen, by calculating the
volume (L x W x H). Multiply this
volume by the air changes per minute.
Example:
Structure Dimensions:
25 L x 24 W x 10 H = 6000 Ft3
Exterior Load Type: Normal
Interior Load Type: Normal
Location: Dallas, Texas – Zone 3
Air Changes Per Minute: 3/4
Evaporative Cooler Requirements:
6000 Ft3 x 3/4 Air Change/Minute =
4500 CFM Required
See the evaporative cooler
performance chart for unit size that
would best apply.
Table SP-1 — Air Changes Per Minute
Type Heat Load
High Load/High Gain
High Load/Normal Gain
Normal Load/High Gain
Normal Load/Normal Gain
For SI metric conversion, see Table G-2 on page 11.
17
1
3
/4
1
/2
1
/2
1
/2
Zone
2
3
1 1 1/3
3
/4
1
3
/4
1
1
3
/2
/4
4
2
1 1/3
1 1/3
1
Cooling Coils
Cooling coils are used in air handling
systems to cool and dehumidify an air
stream for comfort purposes. To reduce
the cooling load in buildings, most
applications recirculate a large
percentage of the air. Usually
recirculated air is 75 to 80 percent of
the airflow with the remainder being
outside fresh air. Some codes require
100 percent outside air, particularly for
hospitals and schools. Also many
engineers specify higher percentages
of outside air to meet the requirements
of ASHRAE Standard 62-1989
“Ventilation for Acceptable Indoor Air
Quality.”
1
In order to select the least expensive
coil to meet the specific performance
criteria, the following information is
required:
- Unit size
- Airflow in scfm or acfm and altitude
(see “Fan Selection at Altitude“)
- Entering air dry bulb and wet bulb
temperatures based on ratio of
outside to return air.
- Cooling load MBh (1000’s Btu/h) or
leaving air wet bulb.
2
For chilled water coils, the following
additional information is required.
- Fluid type: water, ethylene glycol,
propylene glycol and percent of
mixture.
- Entering fluid temperature – F
- Leaving fluid temperature – F or rate
of flow gpm.
Chilled water catalog tables are based
on:
45 F entering water temperature
Entering air temperature of 80 F DB/
67 F WB. Data is certified in
accordance with ARI Standard 410.
For other than these conditions,
please consult the factory.
Selection
Procedure
3
For DX (refrigerant) coils, the following
additional information is required:
- Refrigerant type
- Suction temperature – F
- Liquid temperature – F
- Type of circuiting desired
- Is hot gas bypass required?
DX catalog tables are based on:
45 F suction temperature
Entering air temperature of 80 F DB/67
F WB
R-22 refrigerant
100 F liquid temperature
Data is certified in accordance with ARI
Standard 410. For other than these
conditions, please consult the factory.
4
When specifying a coil, one of the most
important pieces of information is the
airflow in scfm. As stated in the “Fan
Selection at Altitude” section, scfm
means Standard cfm or air at a density
of 0.075 lb./cu. ft. A fan must be
selected using acfm or actual cfm. A
cooling coil or heating coil must be
selected using scfm. Up to an altitude
of approximately 1,500 feet above sea
level, very little error would be
introduced in the selection of a cooling
coil. For altitudes above 1,500 feet
above sea level, the coil must be
selected using scfm. The relationship
between acfm and scfm is shown by
the following equation:
SCFM = ACFM x (Actual Density
÷ 0.075)
The term “0.075 ÷ Actual Density” is
referred to as the density correction
factor, herein called the “Factor.” This
factor can be found in Table PAF-1. The
previous equation can then be
rewritten as:
5
The entering air temperatures, both
wet bulb and dry bulb, must also be
considered when selecting a coil. A
majority of units usually use
recirculated air with a percentage of
outside air. The cooling coil must be
selected using the mixed air
temperature entering the coil.
The following example shows how to
calculate the mixed air temperature:
25 percent outside air at
95 F DB/75 F WB
75 percent recirculated air at
78 F DB/67 F WB
The mixed dry bulb is simply the
proportional value between the outside
and recirculated dry bulb temperatures.
.25 x 95 + .75 x 78 = 82.3 F
The mixed wet bulb temperatures
must be calculated using either the
humidity ratio from a psychrometric
chart or from Table SP-2, The enthalpy
of saturated air at various wet bulb
temperatures.
Using Table SP-2, the enthalpy of the
outside air at 75 F WB is 38.62 Btu/lb.
and the recirculated air at 67 F WB is
31.63 Btu/lb., the mixed enthalpy is:
.25 x 38.62 + .75 x 31.63 = 33.38 Btu/lb.
Using this value in Table SP-2, the
interpolated wet bulb temperature is
69.1 F.
So the final mixed temperatures are:
82.3 F DB/69.1 F WB
SCFM = (ACFM ÷ Factor)
Example: A cooling coil must be
selected at 5,000 ft. altitude. The unit
delivers 10,000 acfm. What is the scfm?
At 5,000 ft. altitude, the factor from
Table PAF-1 is 1.20, therefore:
SCFM = 10,000 ACFM ÷ 1.20 =
8.333 SCFM
For SI metric conversion, see Table G-2 on page 11.
18
Table SP-2 — Enthalpy of Saturated Air at
Various Wet Bulb
Temperatures
Wet Bulb
Temp.
50
50.5
51
51.5
52
52.5
53
53.5
54
54.5
55
55.5
56
56.5
57
57.5
58
58.5
59
59.5
60
60.5
61
61.5
62
62.5
63
63.5
64
64.5
BTU per
Pound
20.38
20.64
20.90
21.17
21.45
21.73
22.01
22.29
22.59
22.88
23.18
23.48
23.79
24.10
24.42
24.74
25.06
25.39
25.73
26.06
26.40
26.75
27.10
27.45
27.81
28.17
28.54
28.91
29.29
29.67
Wet Bulb
Temp.
65
65.5
66
66.5
67
67.5
68
68.5
69
69.5
70
70.5
71
71.5
72
72.5
73
73.5
74
74.5
75
75.5
76
76.5
77
77.5
78
78.5
79
79.5
BTU per
Pound
30.05
30.44
30.83
31.23
31.63
32.03
32.44
32.86
33.27
33.70
34.12
34.55
34.99
35.42
35.87
36.31
36.77
37.22
37.68
38.15
38.61
39.09
39.56
40.04
40.53
41.02
41.51
42.01
42.51
43.02
Performance
Adjustment
Factors
Table PAF-1 — Correction Factors for Altitude
Temp.
F
-40
0
40
70
80
100
120
0’
500’
1000’
39.92
0.79
0.87
0.94
1.00
1.02
1.06
1.90
29.38
0.81
0.88
0.96
1.02
1.04
1.08
1.11
28.86
0.82
0.90
0.98
1.04
1.06
1.10
1.13
Altitude (Feet)
1500’ 2000’ 2500’ 3000’ 3500’ 4000’ 4500’ 5000’ 5500’ 6000’
Barometric Pressure (In. Hg)
28.33 27.82 27.31 26.82 26.32 25.84 25.36 24.90 24.43 29.98
0.84
0.85 0.87
0.88
0.90
0.92 0.93
0.95
0.97
0.99
0.92
0.93 0.95
0.97
0.99
1.00 1.02
1.04
1.06
1.08
1.00
1.01 1.03
1.05
1.07
1.09 1.11
1.13
1.16
1.18
1.06
1.08 1.10
1.12
1.14
1.16 1.18
1.20
1.22
1.25
1.08
1.10 1.12
1.14
1.16
1.18 1.20
1.22
1.25
1.27
1.12
1.14 1.16
1.18
1.20
1.22 1.25
1.27
1.29
1.32
1.16
1.18 1.20
1.22
1.24
1.27 1.29
1.31
1.34
1.37
1. Actual ESP = Duct ESP x Factor ÷ Accs. SP
2. Actual BHP = Cat. BHP ÷ Factor
3. Correct BTUH Input = Catalog BTUH Input ÷ Factor
4. Corrected BTUH Output = Corrected BTUH Input x Efficiency
19
Performance
Data
Table PD-1 – Standard or High Efficiency Indoor Duct Furnace – Arrangement A – 500-1200 MBh Performance Data
Input
Capacity
(CA)
50
60
70
80
12
(Max.)
MBH
(kW)
500
(146.4)
600
(175.7)
700
(205.0)
800
(234.3)
1200
(351.4)
Output
(Min.)
MBH
(kW)
250
(73.2)
300
(87.8)
350
(102.5)
400
(117.1)
600
(175.7)
MBH
(kW)
400
(117.1)
480
(140.6)
560
(164.0)
640
(187.4)
960
(281.1)
Min.
CFM
(cu. m/s)
2315
(1.093)
2778
(1.311)
3241
(1.530)
3704
(1.748)
3704
(1.748)
Temp. Rise
Deg. F
(Deg. C)
160
(89)
160
(89)
160
(89)
160
(89)
180
(100)
P.D.
in. W.C.
(kPa)
0.28
(0.07)
0.26
(0.06)
0.26
(0.06)
0.28
(0.07)
0.42
(0.10)
Max.
CFM
(cu. m/s)
6173
(2.914)
7407
(3.496)
8642
(4.079)
9877
(4.662)
9877
(4.662)
Temp. Rise
Deg. F
(Deg. C)
60
(33)
60
(33)
60
(33)
60
(33)
90
(50)
P.D.
in. W.C.
(Pascals)
0.96
(0.24)
1.00
(0.25)
0.96
(0.24)
1.00
(0.25)
1.50
(0.37)
Notes:
Ratings shown are for unit installations at elevations between 0 and 2,000 ft. (610 m). For unit installations in U.S.A. above 2,000 ft. (610 m), the unit input must
be derated 4% for each 1,000 ft. (305 m) above sea level; refer to local codes, or in absence of local codes, refer to National Fuel Gas Code, ANSI Standard
Z223.1-1992 (N.F.P.A. No. 54) or the latest edition.
For installations in Canada, any references to deration at altitudes in excess of 2,000 ft. (610 m) are to be ignored. At altitudes of 2,000 to 4,500 ft. (610 to 1372 m),
the unit must be derated to 90% of the normal altitude rating, and be so marked in accordance with the CGA certification.
20
Performance
Data
Table PD-2 – Standard or High Efficiency Indoor Make-Up Air Handler — Arrangements B,D — 100-400 MBh Performance Data
Capacity
10
15
20
25
30
35
40
TR
(F)
82
74
61
53
46
41
37
34
31
79
74
55
44
37
32
31
82
74
59
49
42
37
33
30
80
74
61
53
46
41
37
34
82
74
55
44
37
34
81
65
52
43
37
32
30
80
74
59
49
42
37
35
CFM
900
1,000
1,200
1,400
1,600
1,800
2,000
2,200
2,400
1,400
1,500
2,000
2,500
3,000
3,500
3,600
1,800
2,000
2,500
3,000
3,500
4,000
4,500
4,900
2,300
2,500
3,000
3,500
4,000
4,500
5,000
5,500
2,700
3,000
4,000
5,000
6,000
6,500
3,200
4,000
5,000
6,000
7,000
8,000
8,500
3,700
4,000
5,000
6,000
7,000
8,000
8,500
Input Btu/Hr.
Max.
Min.
Max.
Output
Btu/Hr.
100,000
40,000
80,000
150,000
60,000
120,000
200,000
80,000
160,000
250,000
300,000
350,000
400,000
100,000
120,000
140,000
160,000
200,000
240,000
280,000
320,000
0.4
RPM BHP
730
.18
745
.21
795
.29
850
.39
910
.52
980
.68
1050
.87
1125 1.11
1200 1.38
745
.31
770
.35
895
.65
1035 1.13
1180 1.84
1335 2.79
1370 3.02
640
.33
665
.41
740
.66
825 1.02
915 1.50
1005 2.12
1105 2.91
1185 3.67
685
.52
715
.63
790
.96
875 1.41
960 1.99
1055 2.73
1145 3.65
1240 4.76
740
.58
775
.72
905 1.33
1045 2.30
1195 3.73
1275 4.64
630
.55
690
.86
770 1.40
860 2.18
960 3.22
1060 4.56
650
670
745
830
925
1020
.70
.82
1.34
2.07
3.04
4.31
Total Adjusted Static Pressure (Inches of Water)
0.8
1
1.4
1.8
RPM BHP
RPM BHP
RPM BHP
RPM BHP
965
.33
1065
.41
1230
.58
1375
.76
980
.37
1080
.46
1245
.64
1390
.83
1015
.47
1110
.57
1280
.77
1425
.99
1050
.59
1145
.69
1310
.92
1455 1.16
1095
.73
1180
.85
1340 1.09
1485 1.36
1145
.90
1225 1.03
1375 1.29
1515 1.57
1200 1.11
1275 1.24
1420 1.52
1550 1.82
1265 1.36
1330 1.50
1465 1.79
1590 2.11
1330 1.66
1390 1.80
1515 2.11
1635 2.44
960
.49
1055
.59
1235
.81
1385 1.05
970
.54
1065
.65
1240
.87
1395 1.12
1060
.89
1135 1.00
1285 1.26
1425 1.54
1180 1.40
1245 1.55
1370 1.84
1490 2.14
1310 2.12
1370 2.28
1480 2.64
1585 2.98
1450 3.10
1505 3.27
1605 3.66
1705 4.07
1475 3.34
1530 3.50
1630 3.89
1730 4.32
830
.51
915
.62
1060
.84
1200 1.09
845
.60
925
.71
1075
.95
1205 1.20
895
.89
970 1.02
1105 1.28
1230 1.56
965 1.29
1030 1.43
1150 1.72
1265 2.03
1040 1.82
1100 1.98
1210 2.31
1315 2.64
1120 2.48
1175 2.67
1275 3.04
1375 3.41
1205 3.31
1255 3.52
1350 3.93
1440 4.35
1280 4.11
1325 4.33
1415 4.78
850
.74
930
.85
1075 1.10
1205 1.36
875
.86
945
.98
1085 1.23
1210 1.51
935 1.23
1000 1.37
1125 1.66
1240 1.96
1005 1.72
1065 1.88
1175 2.21
1285 2.54
1080 2.35
1135 2.53
1240 2.90
1340 3.27
1160 3.12
1210 3.32
1305 3.74
1400 4.15
1245 4.06
1290 4.29
1380 4.74
2
RPM
1440
1455
1490
1520
1550
1585
1615
1655
1695
1460
1465
1495
1550
1640
1750
1775
1265
1265
1290
1320
1365
1420
1485
BHP
.86
.93
1.10
1.28
1.49
1.72
1.98
2.27
2.61
1.17
1.24
1.69
2.30
3.16
4.27
4.53
1.23
1.34
1.70
2.19
2.82
3.60
4.56
1260
1270
1295
1335
1385
1445
1.50
1.66
2.12
2.71
3.46
4.36
960
975
1070
1190
1325
.94
1.09
1.80
2.85
4.30
1055
1070
1145
1255
1385
1.14
1.30
2.03
3.14
4.64
1235
1245
1290
1380
1.58
1.76
2.55
3.72
1390
1395
1435
1500
2.04
2.25
3.11
4.33
1460
1470
1500
1560
2.27
2.50
3.41
4.65
830
865
925
995
1080
.91
1.26
1.88
2.73
3.86
915
945
995
1060
1135
1.10
1.48
2.12
3.02
4.18
1070
1090
1125
1180
1245
1.55
1.95
2.65
3.60
4.84
1210
1220
1250
1290
2.05
2.47
3.22
4.22
1280
1280
1310
1345
2.31
2.75
3.51
4.55
835
845
900
970
1045
1.08
1.22
1.81
2.62
3.68
920
930
975
1035
1105
1.29
1.43
2.05
2.90
4.01
1070
1075
1110
1155
1215
1.74
1.90
2.57
3.48
4.66
1200
1205
1235
1270
2.25
2.42
3.13
4.09
1265
1265
1295
1325
2.52
2.69
3.43
4.41
Notes:
1. Values in this table are based on the basic package unit that includes blower and duct furnace(s).
2. Brake horsepower (BHP) includes typical belt losses.
3. Unit leaving air temperature (LAT) is limited to 150 F LAT = Entering Air Temperature (EAT) + Temperature Rise (TR).
4. Total External Static Pressure = Accessory Pressure Losses + External Static Pressure.
21
Performance
Data
Table PD-3 – Standard or High Efficiency Indoor Make-Up Air Handler – Arrangements B,D – 500-800 MBh Performance Data
Capacity
50
60
70
80
TR
(F)
160
147
123
105
92
82
74
71
164
147
111
88
74
161
129
103
86
74
69
159
147
118
88
84
79
CFM
2,300
2,500
3,000
3,500
4,000
4,500
5,000
5,200
2,700
3,000
4,000
5,000
6,000
3,200
4,000
5,000
6,000
7,000
7,500
3,700
4,000
5,000
6,000
7,000
7,500
Input Btu/Hr.
Max.
Min.
500,000
600,000
700,000
800,000
200,000
240,000
280,000
320,000
Max.
Output
Btu/Hr.
400,000
480,000
560,000
640,000
0.4
RPM BHP
735
.58
765
.70
855 1.08
950 1.59
1050 2.26
1155 3.11
1260 4.15
1300 4.62
800
.67
840
.83
1000 1.59
1170 2.76
1350 4.44
690
.64
765 1.02
870 1.70
985 2.68
1105 4.00
1165 4.81
705
.80
730
.95
825 1.57
930 2.46
1040 3.66
1100 4.39
Total Adjusted Static Pressure (Inches of Water)
0.8
1
1.4
1.8
RPM BHP
RPM BHP
RPM BHP
RPM BHP
895
.80
970
.91
1110 1.17
1235 1.44
920
.93
990 1.06
1125 1.32
1250 1.60
995 1.36
1055 1.50
1175 1.79
1290 2.10
1075 1.92
1130 2.08
1240 2.41
1345 2.75
1165 2.63
1215 2.81
1315 3.18
1410 3.56
1255 3.52
1305 3.72
1395 4.14
1485 4.55
1350 4.60
1395 4.83
2
RPM
1295
1305
1345
1395
1455
1530
BHP
1.58
1.75
2.26
2.92
3.75
4.76
1010
1035
1150
1300
1.05
1.22
2.06
3.35
1105
1130
1225
1360
1.25
1.45
2.31
3.64
1275
1295
1370
1480
1.69
1.92
2.86
4.24
1425
1445
1510
1600
2.16
2.41
3.44
4.89
1495
1510
1575
2.40
2.67
3.75
875
930
1010
1110
1215
1.01
1.44
2.20
3.25
4.66
960
1010
1080
1170
1270
1.22
1.67
2.46
3.55
4.99
1110
1145
1210
1280
1.68
2.16
3.01
4.16
1250
1270
1325
1390
2.19
2.70
3.60
4.82
1315
1330
1380
2.46
2.99
3.91
885
900
975
1060
1160
1.20
1.36
2.05
3.02
4.30
965
980
1040
1120
1210
1.41
1.58
2.31
3.31
4.63
1105
1120
1175
1235
1.88
2.07
2.85
3.91
1240
1245
1295
1350
2.40
2.60
3.43
4.55
1300
1305
1350
1400
2.68
2.88
3.73
4.88
Notes:
1. Values in this table are based on the basic package unit that includes blower and duct furnace(s).
2. Brake horsepower (BHP) includes typical belt losses.
3. Unit leaving air temperature (LAT) is limited to 150 F LAT = Entering Air Temperature (EAT) + Temperature Rise (TR).
4. Total External Static Pressure = Accessory Pressure Losses + External Static Pressure.
22
Performance
Data
Table PD-4 – Standard or High Efficiency Indoor Make-Up Air Handler – Arrangements B,D – 100-400 MBh Accessory Pressure Loss
Capacity
10
15
20
25
30
35
40
CFM
900
1,000
1,200
1,400
1,600
1,800
2,000
2,200
2,400
1,400
1,500
2,000
2,500
3,000
3,500
3,600
1,800
2,000
2,500
3,000
3,500
4,000
4,500
4,900
2,300
2,500
3,000
3,500
4,000
4,500
5,000
5,500
2,700
3,000
4,000
5,000
6,000
6,500
3,200
4,000
5,000
6,000
7’000
8,000
8,500
3,700
4,000
5,000
6,000
7,000
8,000
8,500
Rainhood
with
Screen
Mstr. Elim.
.01
.02
.01
.02
.02
.03
.03
.04
.04
.05
.05
.06
.06
.07
.07
09
.08
.11
.03
.04
.03
.04
.06
.07
.09
.12
.13
.17
.18
.23
.19
.24
.02
.03
.03
.04
.04
.06
.06
.08
.09
.11
.11
.15
.14
.19
.17
.22
.04
.05
.04
.06
.06
.08
.09
.11
.11
.15
.14
.19
.17
.23
.21
.28
.03
.04
.04
.05
.06
.09
.10
.13
.14
.19
.17
.23
.04
.05
.06
.09
.10
.13
.14
.19
.20
.26
.26
.34
.29
.39
.04
.06
.05
.07
.08
.11
.11
.15
.16
.21
.20
.27
.23
.31
Throwaway
2”
.03
.04
.05
.06
.07
.08
.09
.10
.12
.06
.06
.09
.12
.16
.19
—
.06
.07
.09
.12
.14
.17
—
—
.08
.09
.12
.14
.17
—
—
—
.07
.08
.12
.16
—
—
.09
.12
.16
—
—
—
—
.09
.10
.13
.17
—
—
—
Pressure Loss (Inches of Water)
Filters
Washable
Pleated
1”
2”
1”
2”
<.01
<.01
.03
.02
<.01
<.01
.04
.02
<.01
<.01
.05
.03
<.01
.01
.06
.03
.01
.02
.08
.04
.02
.02
.10
.05
.02
.03
.12
.07
.02
.03
.14
.08
.03
.04
.16
.09
<.01
.01
.06
.03
.01
.02
.07
.04
.02
.03
.12
.07
.03
.04
.17
.10
.04
.06
.23
.14
.06
.08
.30
.18
.06
.09
.31
.19
<.01
.01
.07
.04
.01
.02
.08
.04
.02
.03
.12
.07
.03
.04
.16
.09
.04
.05
.21
.12
.05
.07
.26
.16
.06
.09
.31
.19
.07
.10
.36
.22
.02
.02
.10
.06
.02
.03
.12
.07
.03
.04
.16
.09
.04
.05
.21
.12
.05
.07
.26
.16
.06
.09
.31
.19
.07
.11
.38
.23
.09
.13
.44
.28
.01
.02
.09
.05
.02
.02
.10
.06
.03
.04
.17
.10
.04
.06
.24
.14
.06
.09
.33
.20
.07
.11
.38
.23
.02
.03
.11
.06
.03
.04
.17
.10
.04
.06
.24
.14
.06
.09
.33
.20
.09
.13
.43
.27
.11
.16
—
—
.13
.18
—
—
.02
.03
.11
.06
.02
.03
.13
.07
.03
.05
.19
.11
.05
.07
.26
.16
.07
.09
.33
.21
.09
.12
.42
.26
.10
.14
—
—
23
Evaporative
Cooling Pad
8”
12”
<.01
.01
.01
.02
.02
.02
.02
.03
.03
.04
.04
.06
.05
.07
.06
.08
.07
.10
.02
.03
.03
.04
.05
.07
.07
.11
.10
.15
.14
.21
.15
.22
.02
.03
.03
.04
.04
.06
.06
.09
.08
.12
.10
.15
.13
.20
.16
.23
.03
.05
.04
.06
.06
.09
.08
.12
.10
.15
.13
.20
.16
.24
20
.29
.03
.04
.04
.05
.06
.10
.10
.15
.14
.21
.17
.25
.04
.06
.06
.10
.10
.15
.14
.21
.20
.29
—
—
—
—
.04
.07
.05
.08
.08
.12
.12
.18
.16
.24
.21
.31
—
—
Return or
Outside Air
Damper
.02
.02
.03
.04
.06
.07
.09
.10
.12
.04
.05
.09
.13
.19
.25
.27
.03
.04
.06
.08
.11
.15
.19
.22
.05
.06
.08
.11
.15
.19
.23
.28
.04
.05
.08
.13
.19
.22
.05
.08
.13
.19
.25
.33
.37
.06
.07
.10
.15
.20
.26
.30
Performance
Data
Table PD-5 – Standard or High Efficiency Indoor Make-Up Air Handler – Arrangements B,D – 500-800 MBh Accessory Pressure Loss
Capacity
50
60
70
80
CFM
2,300
2,500
3,000
3,500
4,000
4,500
5,000
5,200
2,700
3,000
4,000
5,000
6,000
3,200
4,000
5,000
6,000
7,000
7,500
3,700
4,000
5,000
8,000
7,000
7,500
Rainhood
with
Screen
Mstr. Elim.
.04
.05
.04
.06
.06
.08
.09
.11
.11
.15
.14
.19
.17
.23
.19
.25
.03
.04
.04
.05
.06
.09
.10
.13
.14
.19
.04
.05
.06
.09
.10
.13
.14
.19
.20
.26
.22
.30
.04
.06
.05
.07
.08
.11
.11
.15
.16
.21
.18
.24
Throwaway
2”
.08
.09
.12
.14
.17
—
—
—
.07
.08
.12
.16
—
.09
.12
.16
—
—
—
.09
.10
.13
.17
—
—
Pressure Loss (Inches of Water)
Filters
Washable
Pleated
1”
2”
1”
2”
.02
.02
.10
.06
.02
.03
.12
.07
.03
.04
.16
.09
.04
.05
.21
.12
.05
.07
.26
.16
.06
.09
.31
.19
.07
.11
.38
.23
.08
.12
.40
.25
.01
.02
.09
,05
.02
.02
.10
.06
.03
.04
.17
.10
.04
.06
.24
.14
.06
.09
.33
.20
.02
.03
.11
.06
.03
.04
.17
.10
.04
.06
.24
.14
.06
.09
.33
.20
.09
.13
.43
.27
10
.14
.
.02
.03
.11
.06
.02
.03
.13
.07
.03
.05
.19
.11
.05
.07
.26
.16
.07
.09
.33
.21
.07
.11
.38
.23
24
Evaporative
Cooling Pad
8”
12”
.03
.05
.04
.06
.06
.09
.08
.12
.10
.15
.13
.20
.16
.24
.17
.26
.03
.04
.04
.05
.06
.10
.10
.15
.14
.21
.04
.06
.06
.10
.10
.15
.14
.21
.20
.29
22
.34
.04
.07
.05
.08
.08
.12
.12
.18
.16
.24
.18
.28
Return or
Outside Air
Damper
.05
.06
.08
.11
.15
.19
.23
.25
.04
.05
.08
.13
.19
.05
.08
.13
.19
.25
.29
.06
.07
.10
.15
.20
.23
Performance
Data
Table PD-6 – Standard or High Efficiency Indoor Make-Up Air Handler – Arrangements G – 200-400 MBh Performance Data
Capacity
20
25
30
35
40
TR
(F)
82
74
59
49
42
37
33
30
80
74
61
53
46
41
37
34
82
74
55
44
37
32
30
81
65
52
43
37
32
30
80
74
59
49
42
37
33
30
CFM
1,800
2,000
2,500
3,000
3,500
4,000
4,500
4,900
2,300
2,500
3,000
3,500
4,000
4,500
5,000
5,500
2,700
3,000
4,000
5,000
6,000
7,000
7,400
3,200
4,000
5,000
6,000
7,000
8,000
8,600
3,700
4,000
5,000
6,000
7,000
8,000
9,000
9,800
Input Btu/Hr.
Max.
Min.
Max.
Output
Btu/Hr.
200,000
80,000
160,000
250,000
100,000
200,000
300,000
120,000
240,000
350,000
140,000
280,000
400,000
160,000
320,000
0.4
RPM BHP
495
.29
510
.35
560
.55
620
.84
685 1.23
755 1.73
825 2.37
885 2.98
520
.43
540
.52
595
.79
655 1.15
720 1.61
790 2.21
860 2.95
935 3.84
520
.47
530
.56
595
.95
670 1.55
750 2.40
840 3.54
875 4.09
495
.50
530
.74
585 1.17
650 1.79
720 2.65
795 3.75
840 4.54
500
.61
515
.70
565 1.11
625 1.70
695 2.50
760 3.52
835 4.82
895 6.07
Total Adjusted Static Pressure (Inches of Water)
0.8
1
1.4
1.8
RPM BHP
RPM BHP
RPM BHP
RPM BHP
650
.49
720
.59
835
.82
940 1.07
665
.56
730
.67
845
.91
950 1.17
695
.79
755
.92
870 1.20
970 1.48
735 1.09
795 1.24
900 1.56
995 1.88
790 1.50
840 1.65
935 2.00
1025 2.37
845 2.04
890 2.20
975 2.55
1060 2.95
905 2.72
950 2.90
1025 3.25
1105 3.65
960 3.36
995 3.56
1070 3.94
1140 4.34
665
.66
730
.78
845 1.04
945 1.31
675
.75
740
.88
855 1.15
955 1.44
710 1.03
770 1.17
875 1.49
975 1.81
760 1.42
810 1.56
905 1.89
1000 2.26
810 1.93
855 2.08
945 2.41
1030 2.79
870 2.55
910 2.73
990 3.08
1065 3.45
930 3.31
995 3.51
1040 3.90
1110 4.29
995 4.22
1025 4.43
1095 4.87
1160 5.30
705
.89
785 1.12
915 1.60
1025 2.10
710
.99
790 1.24
925 1.76
1035 2.29
740 1.43
810 1.70
940 2.30
1060 2.96
795 2.10
850 2.39
965 3.03
1075 3.74
860 3.02
910 3.35
1010 4.05
1105 4.80
935 4.25
985 4.62
1070 5.38
1155 6.19
970 4.84
1015 5.22
1100 6.02
1180 6.85
665
.87
720 1.07
840 1.51
940 2.00
680 1.17
745 1.40
860 1.88
960 2.41
720 1.67
780 1.94
890 2.50
985 3.07
765 2.33
820 2.64
925 3.29
1015 3.94
825 3.21
870 3.53
965 4.25
1055 5.01
885 4.37
930 4.70
1015 5.44
1095 6.27
925 5.21
965 5.55
1045 6.30
1125 7.15
660 1.02
725 1.23
840 1.69
945 2.20
665 1.13
730 1.36
850 1.83
950 2.35
700 1.60
760 1.87
875 2.41
975 2.99
745 2.21
800 2.51
905 3.15
1000 3.81
795 3.05
845 3.35
940 4.05
1030 4.80
855 4.15
900 4.47
985 5.17
1070 5.97
915 5.53
960 5.88
1035 6.59
1115 7.40
970 6.84
1010 7.23
1080 7.99
1150 8.80
Notes:
1. Values in this table are based on the basic package unit that includes blower and duct furnace(s).
2. Brake horsepower (BHP) includes typical belt losses.
3. Unit leaving air temperature (LAT) is limited to 150 F LAT = Entering Air Temperature (EAT) + Temperature Rise (TR).
4. Total External Static Pressure = Accessory Pressure Losses + External Static Pressure.
25
2
RPM
985
995
1015
1040
1065
1100
1140
1175
995
1000
1020
1040
1070
1105
1145
1195
1070
1085
1110
1125
1155
1200
1220
985
1005
1030
1060
1095
1135
1165
990
995
1020
1045
1075
1110
1150
1190
BHP
1.20
1.31
1.63
2.05
2.56
3.16
3.87
4.55
1.45
1.58
1.98
2.45
3.00
3.66
4.49
5.51
2.36
2.57
3.30
4.12
5.19
6.61
7.28
2.25
2.68
3.37
4.28
5.38
6.70
7.60
2.47
2.63
3.29
4.14
5.18
6.40
7.85
9.24
Performance
Data
Table PD-7 – Standard or High Efficiency Indoor Make-Up Air Handler – Arrangement K – 100-400 MBh Performance Data
Capacity
10
15
20
25
30
35
40
TR
(F)
82
74
61
53
46
41
37
34
31
79
74
55
44
37
32
31
82
74
59
49
42
37
33
30
80
74
61
53
46
41
37
34
82
74
55
44
37
32
30
81
65
52
43
37
32
30
80
74
59
49
42
37
33
30
CFM
900
1,000
1,200
1,400
1,600
1,800
2,000
2,200
2,400
1,400
1,500
2,000
2,500
3,000
3,500
3,600
1,800
2,000
2,500
3,000
3,500
4,000
4,500
4,900
2,300
2,500
3,000
3,500
4,000
4,500
5,000
5,500
2,700
3,000
4,000
5,000
6,000
7,000
7,400
3,200
4,000
5,000
6,000
7,000
8,000
8,600
3,700
4,000
5,000
6,000
7,000
8,000
9,000
9,800
Input Btu/Hr.
Max.
Min.
Max.
Output
Btu/Hr.
100,000
40,000
80,000
150,000
60,000
,
120,000
200,000
80,000
160,000
250,000
100,000
200,000
300,000
120,000
240,000
350,000
140,000
280,000
400,000
160,000
320,000
0.4
RPM BHP
730
.18
745
.21
795
.29
850
.39
910
.52
980
.68
1050
.87
1125 1.11
1200 1.38
745
.31
770
.35
895
.65
1035 1.13
1180 1.84
1335 2.79
1370 3.02
495
.29
510
.35
560
.55
620
.84
665 1.23
755 1.73
825 2.37
885 2.98
520
.43
540
.52
595
.79
655 1.15
720 1.61
790 2.21
860 2.95
935 3.84
520
.47
530
.56
595
.95
670 1.55
750 2.40
840 3.54
875 4.09
495
.50
530
.74
585 1.17
650 1.79
720 2.65
795 3.75
840 4.54
500
.61
515
.70
565 1.11
625 1.70
695 2.50
760 3.52
835 4.82
895 6.07
Total Adjusted Static Pressure (Inches of Water)
0.8
1
1.4
1.8
RPM BHP
RPM BHP
RPM BHP
RPM BHP
965
.33
1065
.41
1230
.58
1375
.76
980
.37
1080
.46
1245
.64
1390
.83
1015
.47
1110
.57
1280
.77
1425
.99
1050
.59
1145
.69
1310
.92
1455 1.16
1095
.73
1160
.85
1340 1.09
1485 1.36
1145
.90
1225 1.03
1375 1.29
1515 1.57
1200 1.11
1275 1.24
1420 1.52
1550 1.82
1265 1.36
1330 1.50
1465 1.79
1590 2.11
1330 1.66
1390 1.80
1515 2.11
1635 2.44
960
.49
1055
.59
1235
.81
1385 1.05
970
.54
1065
.65
1240
.87
1395 1.12
1060
.89
1135 1.00
1285 1.26
1425 1.54
1180 1.40
1245 1.55
1370 1.84
1490 2.14
1310 2.12
1370 2.28
1480 2.64
1585 2.98
1450 3.10
1505 3.27
1605 3.66
1705 4.07
1475 3.34
1530 3.50
1630 3.89
1730 4.32
650
.49
720
.59
835
.82
940 1.07
665
.56
730
.67
845
.91
950 1.17
695
.79
755
.92
870 1.20
970 1.48
735 1.09
795 1.24
900 1.56
995 1.88
790 1.50
840 1.65
935 2.00
1025 2.37
845 2.04
890 2.20
975 2.55
1060 2.95
905 2.72
950 2.90
1025 3.25
1105 3.65
960 3.36
995 3.56
1070 3.94
1140 4.34
665
.66
730
.78
845 1.04
945 1.31
675
.75
740
.88
855 1.15
955 1.44
710 1.03
770 1.17
875 1.49
975 1.81
760 1.42
810 1.56
905 1.89
1000 2.26
810 1.93
855 2.08
945 2.41
1030 2.79
870 2.55
910 2.73
990 3.08
1065 3.45
930 3.31
995 3.51
1040 3.90
1110 4.29
995 4.22
1025 4.43
1095 4.87
1160 5.30
705
.89
785 1.12
915 1.60
1025 2.10
710
.99
790 1.24
925 1.76
1035 2.29
740 1.43
810 1.70
940 2.30
1060 2.96
795 2.10
850 2.39
965 3.03
1075 3.74
860 3.02
910 3.35
1010 4.05
1105 4.80
935 4.25
985 4.62
1070 5.38
1155 6.19
970 4.84
1015 5.22
1100 6.02
1180 6.85
665
.87
720 1.07
840 1.51
940 2.00
680 1.17
745 1.40
860 1.88
960 2.41
720 1.67
780 1.94
890 2.50
985 3.07
765 2.33
820 2.64
925 3.29
1015 3.94
825 3.21
870 3.53
965 4.25
1055 5.01
885 4.37
930 4.70
1015 5.44
1095 6.27
925 5.21
965 5.55
1045 6.30
1125 7.15
660 1.02
725 1.23
840 1.69
945 2.20
665 1.13
730 1.36
850 1.83
950 2.35
700 1.60
760 1.87
875 2.41
975 2.99
745 2.21
800 2.51
905 3.15
1000 3.81
795 3.05
845 3.35
940 4.05
1030 4.80
855 4.15
900 4.47
985 5.17
1070 5.97
915 5.53
960 5.88
1035 6.59
1115 7.40
970 6.84
1010 7.23
1080 7.99
1150 8.80
Notes:
1. Values in this table are based on the basic package unit that includes blower and duct furnace(s).
2. Brake horsepower (BHP) includes typical belt losses.
3. Unit leaving air temperature (LAT) is limited to 150 F LAT = Entering Air Temperature (EAT) + Temperature Rise (TR).
4. Total External Static Pressure = Accessory Pressure Losses + External Static Pressure.
26
2
RPM
1440
1455
1490
1520
1550
1585
1615
1655
1695
1460
1465
1495
1550
1640
1750
1775
985
995
1015
1040
1065
1100
1140
1175
995
1000
1020
1040
1070
1105
1145
1195
1070
1085
1110
1125
1155
1200
1220
985
1005
1030
1060
1095
1135
1165
990
995
1020
1045
1075
1110
1150
1190
BHP
.86
.93
1.10
1.28
1.49
1.72
1.98
2.27
2.61
1.17
1.24
1.69
2.30
3.16
4.27
4.53
1.20
1.31
1.63
2.05
2.56
3.16
3.87
4.55
1.45
1.58
1.98
2.45
3.00
3.66
4.49
5.51
2.36
2.57
3.30
4.12
5.19
6.61
7.28
2.25
2.68
3.37
4.28
5.38
6.70
7.60
2.47
2.63
3.29
4.14
5.18
6.40
7.85
9.24
Performance
Data
Table PD-8 – Standard or High Efficiency Indoor Make-Up Air Handler – Arrangement G, K – 500-800 MBh Performance Data
Capacity
50
60
70
80
TR
(F)
160
147
123
105
92
82
74
67
61
164
147
111
88
74
63
60
161
129
103
86
74
65
60
159
147
118
98
84
74
66
60
CFM
2,300
2,500
3,000
3,500
4,000
4,500
5,000
5,500
6,000
2,700
3,000
4,000
5,000
6,000
7,000
7,400
3,200
4,000
5,000
6,000
7,000
8,000
8,600
3,700
4,000
5,000
6,000
7,000
8,000
9,000
9,800
Input Btu/Hr.
Max.
Min.
Max.
Output
Btu/Hr.
500,000
200,000
400,000
600,000
240,000
480,000
700,000
280,000
560,000
800,000
320,000
640,000
0.4
RPM BHP
560
.48
585
.58
645
.89
715 1.31
790 1.86
865 2.54
945 3.38
1020 4.40
1100 5.62
570
.57
590
.68
675 1.21
775 2.01
880 3.16
995 4.71
1040 5.46
540
.60
595
.92
675 1.48
755 2.27
845 3.35
935 4.75
995 5.78
550
.72
570
.84
635 1.34
710 2.05
790 3.02
875 4.30
960 5.91
1030 7.47
Total Adjusted Static Pressure (Inches of Water)
0.8
1
1.4
1.8
RPM BHP
RPM BHP
RPM BHP
RPM BHP
700
.72
760
.85
875 1.11
975 1.38
715
.83
775
.97
885 1.24
985 1.53
765 1.15
820 1.31
920 1.63
1015 1.96
820 1.59
865 1.75
960 2.11
1050 2.49
880 2.17
925 2.33
1010 2.70
1095 3.11
945 2.89
985 3.07
1065 3.44
1140 3.86
1015 3.78
1055 3.97
1125 4.36
1195 4.79
1090 4.84
1125 5.05
1190 5.48
1255 5.92
1165 6.09
1195 6.33
1255 6.80
1315 7.26
750 1.01
820 1.25
945 1.73
1050 2.24
760 1.15
835 1.40
960 1.92
1065 2.47
815 1.73
885 2.03
1010 2.67
1120 3.34
890 2.61
950 2.93
1055 3.63
1160 4.40
985 3.84
1030 4.20
1125 4.96
1220 5.78
1080 5.48
1125 5.88
1210 6.72
1290 7.60
1125 6.27
1165 6.68
1245 7.55
1320 8.46
690
.98
755 1.19
865 1.64
965 2.13
735 1.36
795 1.59
900 2.09
1000 2.64
795 2.02
850 2.29
950 2.86
1045 3.46
865 2.90
915 3.23
1010 3.88
1095 4.55
940 4.05
985 4.42
1075 5.18
1155 5.94
1020 5.51
1065 5.92
1145 6.77
1220 7.63
1075 6.56
1110 6.99
1190 7.89
1260 8.82
695 1.13
760 1.35
870 1.83
970 2.35
710 1.28
770 1.51
885 2.00
980 2.53
760 1.87
820 2.14
925 2.70
1020 3.29
820 2.65
875 2.97
970 3.62
1060 4.28
890 3.66
935 4.02
1025 4.77
1110 5.52
960 4.97
1005 5.35
1090 6.17
1165 7.03
1040 6.63
1080 7.03
1155 7.89
1225 8.83
1105 8.24
1140 8.65
1210 9.54
1280 10.52
2
RPM
1020
1030
1060
1095
1130
1180
1230
1285
1345
1095
1115
1170
1210
1265
1330
1360
1010
1040
1085
1135
1195
1255
1295
1015
1025
1065
1105
1150
1205
1265
1315
BHP
1.53
1.68
2.13
2.68
3.33
4.09
5.02
6.15
7.50
2.50
2.75
3.69
4.80
6.21
8.06
8.93
2.39
2.92
3.77
4.90
6.32
8.07
9.28
2.62
2.82
3.59
4.62
5.91
7.46
9.31
11.03
Notes:
1. Values in this table are based on the basic package unit that includes blower and duct furnace(s).
2. Brake horsepower (BHP) includes typical belt losses.
3. Unit leaving air temperature (LAT) is limited to 150 F LAT= Entering Air Temperature (EAT) + Temperature Rise (TR).
4. Total External Static Pressure = Accessory Pressure Losses + External Static Pressure.
5. See Tables PD-10, 11, 13 and 14 for cfm limitations on Arrangement K.
Table PD-9 – Standard or High Efficiency Indoor Make-Up Air Handler – Arrangement G – 1200 MBh Performance Data
Capacity
12
TR
(F)
197
177
147
126
111
98
90
Input Btu/Hr.
Max.
Min.
CFM
4,500
5,000
6,000
7,000 1,200,000 480,000
8,000
9,000
9,800
Max.
Output
Btu/Hr.
960,000
0.4
RPM BHP
660 1.26
700 1.60
790 2.46
885 3.63
985 5.15
1080 7.07
1165 8.93
Total Adjusted Static Pressure (Inches of Water)
0.8
1
1.4
1.8
RPM BHP
RPM BHP
RPM BHP
RPM BHP
785 1.75
840 2.01
945 2.55
1035 3.12
820 2.14
875 2.42
975 2.99
1065 3.60
895 3.10
945 3.43
1035 4.09
1120 4.77
980 4.36
1025 4.74
1110 5.49
1185 6.26
1065 5.95
1105 6.38
1185 7.24
1260 8.10
1160 7.94
1195 8.40
1265 9.36
1335 10.33
1235 9.85
1265 10.34
1335 11.36
1400 12.41
Notes:
1. Values in this table are based on the basic package unit that includes blower and duct furnace(s).
2. Brake horsepower (BHP) includes typical belt losses.
3. Unit leaving air temperature (LAT) is limited to 150 F LAT = Entering Air Temperature (EAT) + Temperature Rise (TR).
4. Total External Static Pressure = Accessory Pressure Losses + External Static Pressure.
27
2
RPM
1080
1105
1160
1225
1295
1370
1430
BHP
3.43
3.91
5.12
6.65
8.54
10.81
12.94
Performance
Data
Standard DX Coil Performance Data
Table PD-10 – Indoor Make-Up Air Gas Heating Units – Refrigerant (R-22) DX Coil Performance
Unit
Capacity
(CA)
10
15
20
25, 50
30, 60
35, 70
40, 80
Air
Flow
(SCFM)
1600
Face
Velocity
(FPM)
334
2400
481
1600
334
3000
601
2100
296
4400
596
2500
353
4400
596
2800
299
5800
594
3200
341
5800
594
3700
355
6500
599
Conversions:
2119 SCFM = 1 m/s
196.8 FPM = 1 m/s
3.412 MBH = 1 kW
(F-32) 5/9 = C
1 In. W.C. = 248.8 Pa
1 LB. = 0.453 kg
Fin
Spacing
(FPF)
* 96
* 120
* 144
96
120
144
* 96
* 120
* 144
96
120
144
* 96
* 120
* 144
96
120
144
* 96
* 120
* 144
96
120
144
* 96
* 120
* 144
96
120
144
* 96
* 120
* 144
96
120
144
* 96
* 120
* 144
96
120
144
Capacity
(MBH)
54.2
59.9
64.0
63.5
72.4
80.0
54.2
59.9
64.0
71.3
82.0
91.3
79.4
86.7
91.9
105.6
123.1
138.6
88.6
97.3
103.6
105.6
123.1
138.6
107.3
117.1
124.0
147.7
169.9
189.1
116.7
127.8
135.8
147.7
169.6
189.1
132.3
144.6
153.5
166.3
190.0
210.6
Capacity based on 80 F EDB, 67 F EWB, 45 F Sat. Suction, 100 F Liquid
NUMBER OF ROWS
4
6
L.A.T.
A.P.D.
WT.
Capacity
L.A.T.
A.P.D.
(DB / WB) In.W.C.
(LBS)
(MBH)
(DB / WB)
In.W.C.
57 / 56
0.27
62
68.7
53 / 53
0.41
55 / 55
0.32
65
72.5
52 / 52
0.48
54 / 54
0.37
70
75.8
51 / 51
0.56
61 / 59
0.43
62
81.7
57 / 56
0.63
59 / 58
0.46
65
88.1
55 / 55
0.67
57 / 56
0.49
70
94.5
54 / 54
0.72
57 / 56
0.27
62
68.7
53 / 53
0.41
55 / 55
0.32
65
72.5
52 / 52
0.48
54 / 54
0.37
70
75.8
51 / 51
0.56
62 / 60
0.59
62
89.8
59 / 58
0.87
60 / 58
0.63
65
101.2
57 / 56
0.93
58 / 57
0.67
70
111.1
55 / 55
1.00
56 / 55
0.23
84
95.9
52 / 52
0.34
54 / 54
0.27
89
102.0
51 / 51
0.40
53 / 53
0.31
95
106.2
50 / 50
0.47
62 / 60
0.58
84
142.1
58 / 57
0.87
60 / 58
0.62
89
158.7
56 / 55
0.94
58 / 57
0.66
95
172.3
54 / 54
1.00
57 / 56
0.30
84
108.5
53 / 53
0.45
55 / 54
0.35
89
116.1
52 / 52
0.53
54 / 53
0.41
95
121.3
51 / 51
0.61
62 / 60
0.58
84
142.1
58 / 57
0.87
60 / 58
0.62
89
158.7
56 / 55
0.94
58 / 57
0.66
95
172.3
54 / 54
1.00
55 / 54
0.23
105
126.8
52 / 52
0.34
54 / 53
0.27
112
134.3
51 / 51
0.40
53 / 52
0.32
119
140.1
50 / 50
0.47
61 / 59
0.58
105
187.5
58 / 57
0.87
59 / 58
0.63
112
208.0
56 / 55
0.92
58 / 57
0.67
119
228.2
54 / 54
0.99
56 / 55
0.28
105
139.3
53 / 53
0.43
55 / 54
0.33
112
149.6
51 / 51
0.50
53 / 53
0.39
119
156.6
50 / 50
0.58
61 / 59
0.58
105
187.5
58 / 57
0.87
59 / 58
0.63
112
208.0
56 / 55
0.92
58 / 57
0.67
119
228.2
54 / 54
0.99
56 / 55
0.30
115
161.9
53 / 53
0.46
55 / 54
0.35
122
173.9
51 / 51
0.53
54 / 53
0.41
130
182.1
50 / 50
0.62
61 / 59
0.59
115
209.6
58 / 57
0.88
59 / 58
0.63
122
237.0
56 / 55
0.94
58 / 57
0.68
130
259.7
54 / 54
1.00
Notes:
1.) Data certified in accordance with ARI Standard 410.
2.) Capacity based on 80 F EDB, 67 F EWB, 45 F Sat. Suction, 100 F Liquid.
3.) Weight listed is the total weight of the dry coil.
4.) Coils denoted by an asterisk ( * ) require special pricing; consult your Trane representative for special coil requirements
and pricing.
28
WT.
(LBS)
84
89
95
84
89
95
84
89
95
84
89
95
115
122
130
115
122
130
115
122
130
115
122
130
145
155
166
145
155
166
145
155
166
145
155
166
158
170
182
158
170
182
Performance
Data
Standard DX Coil Performance Data
Table PD-11 – Indoor Make-Up Air Gas Heating Units – Refrigerant (R-22) DX Coil Performance
Unit
Capacity
(CA)
10
15
20
25, 50
30, 60
35, 70
40, 80
Air
Flow
(SCFM)
1600
Face
Velocity
(FPM)
320
2400
481
1600
320
3000
601
2100
244
4400
596
2500
312
4400
596
2800
276
5800
594
3200
328
5800
594
3700
341
6500
599
Conversions:
2119 SCFM = 1 m/s
196.8 FPM = 1 m/s
3.412 MBH = 1 kW
(F-32) 5/9 = C
1 In. W.C. = 248.8 Pa
1 LB. = 0.453 kg
Fin
Spacing
(FPF)
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
Capacity
(MBH)
78.6
87.4
94.3
98.7
111.2
121.7
78.6
87.4
94.3
110.2
124.9
139.2
98.0
108.6
116.7
168.6
194.5
217.7
115.4
129.3
140.5
168.6
194.5
217.7
145.9
161.6
173.5
226.2
257.4
285.0
162.6
181.2
195.8
226.2
257.4
285.0
185.6
206.3
222.4
250.8
287.1
324.3
Capacity based on 80 F EDB, 67 F EWB, 45 F Sat. Suction, 100 F Liquid
NUMBER OF ROWS
4
6
L.A.T.
A.P.D.
WT.
Capacity
L.A.T.
A.P.D.
(DB / WB) In.W.C.
(LBS)
(MBH)
(DB / WB)
In.W.C.
62 / 60
0.23
62
94.2
58 / 57
0.34
59 / 58
0.24
65
102.9
55 / 55
0.36
57 / 56
0.26
70
109.4
53 / 53
0.38
66 / 63
0.43
62
124.4
60 / 59
0.64
63 / 61
0.46
65
138.5
58 / 57
0.68
61 / 60
0.49
70
149.9
56 / 55
0.73
62 / 60
0.23
62
94.2
58 / 57
0.34
59 / 58
0.24
65
102.9
55 / 55
0.36
57 / 56
0.26
70
109.4
53 / 53
0.38
67 / 64
0.59
62
142.9
62 / 61
0.88
65 / 62
0.64
65
161.1
59 / 58
0.94
62 / 61
0.66
70
176.0
57 / 57
1.01
60 / 58
0.14
84
119.5
54 / 54
0.21
57 / 56
0.15
89
127.6
53 / 52
0.23
55 / 55
0.16
95
133.3
51 / 51
0.24
67 / 64
0.58
84
215.7
62 / 60
0.87
64 / 62
0.63
89
238.1
59 / 58
0.94
61 / 60
0.67
95
261.2
57 / 56
1.00
62 / 60
0.22
84
143.1
56 / 56
0.32
59 / 58
0.23
89
154.2
54 / 54
0.35
57 / 56
0.25
95
162.3
53 / 53
0.37
67 / 64
0.58
84
215.7
62 / 60
0.87
64 / 62
0.63
89
238.1
59 / 58
0.94
61 / 60
0.67
95
261.2
57 / 56
1.00
60 / 58
0.18
105
173.4
55 / 55
0.26
57 / 56
0.19
112
185.3
53 / 53
0.28
55 / 55
0.20
119
195.5
52 / 52
0.30
67 / 63
0.58
105
290.6
61 / 60
0.87
64 / 62
0.63
112
326.5
58 / 58
0.93
61 / 60
0.66
119
356.4
56 / 56
1.00
62 / 60
0.24
105
194.7
57 / 56
0.35
59 / 58
0.25
112
212.0
54 / 54
0.38
57 / 56
0.27
119
225.2
53 / 53
0.40
67 / 63
0.58
105
290.6
61 / 60
0.87
64 / 62
0.63
112
326.5
58 / 58
0.93
61 / 60
0.66
119
356.4
56 / 56
1.00
62 / 60
0.25
115
225.6
57 / 56
0.38
59 / 58
0.27
122
245.6
54 / 54
0.40
57 / 56
0.29
130
260.9
53 / 53
0.43
67 / 63
0.59
115
328.1
61 / 60
0.88
64 / 62
0.63
122
367.3
58 / 57
0.95
61 / 60
0.67
130
400.1
56 / 56
1.01
Notes:
1.) Data certified in accordance with ARI Standard 410.
2.) Capacity based on 95 F EDB, 74 F EWB, 45 F Sat. Suction, 100 F Liquid.
3.) Weight listed is the total weight of the dry coil.
4.) Coils denoted by an asterisk ( * ) require special pricing; consult your Trane representative for special coil requirements
and pricing.
29
WT.
(LBS)
84
89
95
84
89
95
84
89
95
84
89
95
115
122
130
115
122
130
115
122
130
115
122
130
145
155
166
145
155
166
145
155
166
145
155
166
158
170
182
158
170
182
Performance
Data
Table PD-12 – Standard Conditions and Specifications – Refrigerant DX Coil
CONDITIONS
Elevation
Entering Air Temperature DB:
Entering Air Temperature WB:
Suction Temperature:
Liquid Temperature:
Fouling Factor:
SPECIFICATIONS
Coil Type:
Tube Size:
Row Sizes:
Fin Type:
Fin Size:
Fin Spacing:
Circuiting:
Turbulators:
DIMENSIONAL DATA LISTING
Unit Size
10, 15
20, 25, 50
30, 35, 60, 70
40, 80
0 Ft.
80 F
95 F
67 F
74 F
45 F
45 F
100 F
100 F
2
0 HR x Ft x F/BTU
FD — Staggered Tube Pattern
1
/2” O.D. x 0.016” TWT Copper
4,6
DE – Optional DH
0.0055” Aluminum
Standard – 96, (120), 144 Fins/Ft.
Optional – 72 thru 180 Fins/Ft.
Standard – Single
Optional – Dual:
a) Intertwined
b) Face-Split
No
Fixed Finned Width
30.00
30.00
30.00
30.00
Note:
1. Above specification is for standard coil with standard fin spacing.
Specify fin spacing and dual circuiting.
2. Special coils — contact your Trane representative.
3. Every order requires a coil selection.
30
Fixed Finned Length
23.00
34.00
45.00
50.00
Performance
Data
Standard Chilled Water Coil Performance Data
Table PD-13 – Indoor Make-Up Air Gas Heating Units – Chilled Water Coil Performance
Unit
Capacity
(CA)
10
15
20
25, 50
30, 60
35, 70
40, 80
Air
Flow
(SCFM)
960
Face
Velocity
(FPM)
200
2400
501
1400
292
2900
605
1800
254
4300
607
2300
325
4300
607
2700
288
5700
608
3200
355
5700
608
3700
355
6300
605
Conversions:
2119 SCFM = 1 m/s
196.8 FPM = 1 m/s
3.412 MBH = 1 kW
(F-32) 5/9 = C
1 In. W.C. = 248.8 Pa
1 LB. = 0.453 kg
Fin
Spacing
(FPF)
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
Capacity
(MBH)
44.6
48.1
50.6
78.5
86.9
93.4
57.9
63.0
67.0
85.8
95.5
103.0
77.4
83.9
89.0
124.8
138.7
149.6
90.5
98.8
105.3
124.8
138.7
149.6
110.1
119.7
127.4
162.1
180.2
194.2
121.9
133.2
142.2
162.1
180.2
194.2
137.7
150.6
160.8
178.0
197.9
213.3
Capacity based on 80 F EDB, 67 F EWB, 45 F EWT, 70 GPM
NUMBER OF ROWS
4
6
L.A.T.
A.P.D.
WT.
Capacity
L.A.T.
(DB / WB) In.W.C.
(LBS)
(MBH)
(DB / WB)
53 / 52
0.08
158
52.0
48 / 48
51 / 50
0.09
164
54.5
47 / 47
49 / 49
0.11
170
56.1
46 / 46
58 / 56
0.35
158
99.7
54 / 53
56 / 55
0.40
164
108.1
52 / 52
55 / 54
0.45
170
114.3
51 / 51
55 / 54
0.15
158
69.9
51 / 50
53 / 52
0.17
164
74.2
49 / 49
51 / 51
0.20
170
77.2
48 / 48
60 / 57
0.46
158
110.7
55 / 54
58 / 56
0.53
164
108.1
54 / 53
56 / 55
0.60
170
114.3
52 / 52
54 / 53
0.12
197
92.3
50 / 50
52 / 51
0.14
206
97.5
49 / 48
51 / 50
0.16
215
101.3
48 / 48
60 / 58
0.47
197
160.4
56 / 55
58 / 57
0.53
206
175.2
54 / 53
57 / 56
0.60
215
186.2
53 / 52
56 / 54
0.17
197
110.4
51 / 51
54 / 53
0.20
206
117.6
50 / 50
52 / 52
0.23
215
123.0
49 / 49
60 / 58
0.47
197
160.4
56 / 55
58 / 57
0.53
206
175.2
54 / 53
57 / 56
0.60
215
186.2
53 / 52
55 / 54
0.14
240
132.8
51 / 50
53 / 52
0.17
252
141.0
49 / 49
52 / 51
0.19
264
147.0
48 / 48
60 / 58
0.47
240
207.6
56 / 55
58 / 57
0.53
252
227.0
55 / 54
57 / 56
0.60
264
241.2
53 / 53
56 / 55
0.19
240
149.2
52 / 51
54 / 53
0.22
252
159.4
50 / 50
53 / 52
0.25
264
167.0
49 / 49
60 / 58
0.47
240
207.6
56 / 55
58 / 57
0.53
252
227.0
55 / 54
57 / 56
0.60
264
241.2
53 / 53
57 / 55
0.20
258
169.1
52 / 52
55 / 54
0.23
271
181.0
51 / 51
53 / 53
0.27
284
189.8
50 / 50
60 / 58
0.47
258
227.8
56 / 55
58 / 57
0.52
271
248.9
55 / 54
57 / 56
0.59
284
264.4
53 / 53
Notes:
1.) Data certified in accordance with ARI Standard 410.
2.) Capacity based on 80 F EDB, 67 F EWB, 45 F EWT, 70 GPM.
3.) Weight listed is the total weight of the coil filled with fluid.
4.) Consult your Trane representative for special coil requirements.
31
A.P.D.
In.W.C.
0.11
0.13
0.16
0.52
0.60
0.68
0.22
0.26
0.29
0.70
0.79
0.90
0.17
0.21
0.24
0.70
0.79
0.90
0.26
0.31
0.35
0.70
0.79
0.90
0.21
0.25
0.29
0.70
0.79
0.90
0.28
0.33
0.38
0.70
0.79
0.90
0.30
0.35
0.40
0.69
0.78
0.89
WT.
(LBS)
204
213
222
204
213
222
204
213
222
204
213
222
260
274
287
260
274
287
260
274
287
260
274
287
324
341
359
324
341
359
324
341
359
324
341
359
349
369
389
349
369
389
Performance
Data
Standard Chilled Water Coil Performance Data
Table PD-14 – Indoor Make-Up Air Gas Heating Units – Chilled Water Coil Performance
Unit
Capacity
(CA)
10
15
20
25, 50
30, 60
35, 70
40, 80
Air
Flow
(SCFM)
960
Face
Velocity
(FPM)
200
2400
501
1400
292
2900
605
1800
254
4300
607
2300
325
4300
607
2700
288
5700
608
3200
355
5700
608
3700
355
6300
605
Conversions:
2119 SCFM = 1 m/s
196.8 FPM = 1 m/s
3.412 MBH = 1 kW
(F-32) 5/9 = C
1 In. W.C. = 248.8 Pa
1 LB. = 0.453 kg
Fin
Spacing
(FPF)
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
96
120
144
Capacity
(MBH)
63.4
68.3
72.0
110.6
122.4
131.8
82.0
89.2
94.9
120.6
134.3
145.0
109.8
119.0
126.3
175.1
195.3
210.8
128.0
139.7
149.0
175.1
195.3
210.8
155.8
169.4
180.2
227.8
253.7
273.7
172.1
188.1
200.8
227.8
253.7
273.7
194.3
212.5
227.1
250.4
278.8
300.7
Capacity based on 95 F EDB, 74 F EWB, 45 F EWT, 70 GPM
NUMBER OF ROWS
4
6
L.A.T.
A.P.D.
WT.
Capacity
L.A.T.
(DB / WB) In.W.C.
(LBS)
(MBH)
(DB / WB)
56 / 54
0.08
158
74.0
50 / 50
53 / 52
0.09
164
77.6
48 / 48
51 / 51
0.11
170
80.0
47 / 47
64 / 61
0.34
158
140.8
58 / 57
61 / 59
0.39
164
152.8
56 / 55
59 / 58
0.44
170
161.8
54 / 53
59 / 57
0.14
158
99.2
53 / 52
56 / 55
0.17
164
105.4
51 / 50
54 / 53
0.19
170
109.8
50 / 49
66 / 62
0.46
158
156.0
60 / 58
63 / 61
0.52
164
170.7
57 / 56
61 / 59
0.59
170
181.6
56 / 55
58 / 56
0.11
197
131.2
52 / 51
55 / 54
0.13
206
138.6
50 / 50
53 / 52
0.15
215
143.9
49 / 49
66 / 62
0.46
197
226.1
60 / 58
63 / 61
0.52
206
247.5
58 / 57
61 / 60
0.59
215
263.2
56 / 56
60 / 57
0.17
197
156.4
54 / 53
57 / 56
0.20
206
166.8
52 / 51
55 / 54
0.23
215
174.4
50 / 50
66 / 62
0.46
197
226.1
60 / 58
63 / 61
0.53
206
247.5
58 / 57
61 / 60
0.59
215
263.2
56 / 56
59 / 57
0.14
240
188.3
53 / 53
56 / 55
0.17
252
200.0
51 / 51
55 / 54
0.19
264
208.6
50 / 50
66 / 63
0.46
240
292.9
61 / 59
64 / 61
0.51
252
320.4
58 / 57
62 / 60
0.59
264
340.8
57 / 56
61 / 58
0.19
240
211.2
55 / 54
58 / 57
0.22
252
225.7
53 / 52
56 / 55
0.25
264
236.7
51 / 51
66 / 63
0.46
240
292.9
61 / 59
64 / 61
0.51
252
320.4
58 / 57
62 / 60
0.59
264
340.8
57 / 56
61 / 59
0.20
258
239.1
55 / 54
58 / 57
0.23
271
256.0
53 / 53
57 / 56
0.26
284
269.0
52 / 52
66 / 63
0.45
258
321.3
61 / 59
64 / 61
0.51
271
351.4
59 / 58
62 / 60
0.58
284
373.6
57 / 56
Notes:
1.) Data certified in accordance with ARI Standard 410.
2.) Capacity based on 95 F EDB, 74 F EWB, 45 F EWT, 70 GPM.
3.) Weight listed is the total weight of the coil filled with fluid.
4.) Consult your Trane representative for special coil requirements.
32
A.P.D.
In.W.C.
0.12
0.14
0.16
0.52
0.59
0.67
0.22
0.26
0.29
0.69
0.78
0.89
0.17
0.20
0.23
0.69
0.78
0.89
0.26
0.31
0.35
0.69
0.78
0.89
0.21
0.25
0.29
0.69
0.77
0.89
0.28
0.33
0.37
0.69
0.77
0.89
0.30
0.35
0.40
0.68
0.77
0.88
WT.
(LBS)
204
213
222
204
213
222
204
213
222
204
213
222
260
274
287
260
274
287
260
274
287
260
274
287
324
341
359
324
341
359
324
341
359
324
341
359
349
369
389
349
369
389
Performance
Data
Table PD-15 – Standard Conditions and Specifications – Chilled Water Coil
CONDITIONS
Elevation
Entering Air Temperature DB:
Entering Air Temperature WB:
Entering Water Temperature:
Water Flow Rate:
Tube Velocity:
Fouling Factor:
SPECIFICATIONS
Coil Type:
Tube Size:
Row Sizes:
Fin Type:
Fin Size:
Fin Spacing:
0 Ft.
80 F
95 F
67 F
78 F
45 F
45 F
70 GPM 70 GPM
4 Ft./Sec.
0 HR x FT2 x F/BTU
W — Full Row Serpentine
5
/8” O.D. x 0.024” TWT Copper
4,6
Prima-Flo®
0.0075” Aluminum
Standard — 96, (120), 144 Fins/Ft.
Optional — 80 thru 168 Fins/Ft.
Single Circuit
Yes
No
Circuiting:
Drainable:
Turbulators:
DIMENSIONAL DATA LISTING
Unit Size
Fixed Finned Width
10, 15
30.00
20, 25, 50
30.00
30, 35, 60, 70
30.00
40, 80
30.00
Note:
1. Above specification is for standard coil with standard fin spacing.
2. Special coils – contact your Trane representative.
3. Every order requires a coil selection.
33
Fixed Finned Length
23.00
34.00
45.00
50.00
Performance
Data
Table PD-16 – Standard or High Efficiency Indoor Make-Up Air Handler – Arrangement G, K – 100-400 MBh – Accessory Pressure Loss
Capacity
10
15
20
25
30
35
40
CFM
900
1,000
1,200
1,400
1,600
1,800
2,000
2,200
2,400
1,400
1,500
2,000
2,500
3,000
3,500
3,600
1,800
2,000
2,500
3,000
3,500
4,000
4,500
4,900
2,300
2,500
3,000
3,500
4,000
4,500
5,000
5,500
2,700
3,000
4,000
5,000
6,000
7,000
7,400
3,200
4,000
5,000
6,000
7,000
8,000
8,600
3,700
4,000
5,000
6,000
7,000
8,000
9,000
9,800
Rainhood
with
Screen
Mstr. Elim.
.01
.02
.01
.02
.02
.03
.03
.04
.04
.05
.05
.06
.06
.07
.07
.09
.08
.11
.03
.04
.03
.04
.06
.07
.09
.12
.13
.17
.18
.23
.19
.24
.02
.03
.03
.04
.04
.06
.06
.08
.09
.11
.11
.15
.14
.19
.17
.22
.04
.05
.04
.06
.06
.08
.09
.11
.11
.15
.14
.19
.17
.23
.21
.28
.03
.04
.04
.05
.06
.09
.10
.13
.14
.19
.20
.26
.22
.29
.04
.05
.06
.09
.10
.13
.14
.19
.20
.26
.26
.34
.30
.40
.04
.06
.05
.07
.08
.11
.11
.15
.16
.21
.20
.27
.26
.35
.31
.41
Pressure Loss (Inches of Water)
Filters
Throwaway
Washable
2”
1”
2”
.01
<.01
<.01
.01
<.01
<.01
.02
<.01
<.01
.02
<.01
<.01
.03
<.01
<.01
.03
<.01
<.01
.04
<.01
<.01
.04
<.01
<.01
.05
<.01
<.01
.02
<.01
<.01
.02
<.01
<.01
.04
<.01
<.01
.05
<.01
.01
.06
.01
.02
.08
.01
.02
.08
.02
.02
.03
<.01
<.01
.04
<.01
<.01
.05
<.01
.01
.06
.01
.02
.08
.01
.02
.09
.02
.03
.11
.02
.03
.12
.03
.04
.04
<.01
<.01
.05
<.01
.01
.06
.01
.02
.08
.01
.02
.09
.02
.03
.11
.02
.03
.12
.03
.04
.14
.04
.05
.03
<.01
<.01
.03
<.01
<.01
.05
<.01
.01
.06
.01
.02
.08
.02
.02
.10
.02
.03
.11
.02
.03
.03
<.01
<.01
.05
<.01
.01
.06
.01
.02
.08
.02
.02
.10
.02
.03
.12
.03
.04
.13
.03
.05
.03
<.01
<.01
.04
<.01
<.01
.05
<.01
.01
.07
.01
.02
.08
.02
.02
.10
.02
.03
.12
.03
.04
.13
.03
.05
34
Pleated
1”
<.01
.01
.02
.02
.03
.03
.04
.04
.05
.02
.02
.04
.05
.07
.09
.10
.03
.04
.05
.07
.09
.12
.14
.16
.05
.05
.07
.09
.12
.14
.17
.20
.03
.03
.05
.08
.10
.13
.15
.04
.05
.08
.10
.13
.17
.19
.04
.04
.06
.08
.10
.13
.16
.18
2”
<.01
<.01
<.01
<.01
.01
.02
.02
.02
.03
<.01
.01
.02
.03
.04
.05
.05
.02
.02
.03
.04
.05
.07
.08
.10
.02
.03
.04
.05
.07
.08
.10
.12
.01
.02
.03
.04
.06
.08
.08
.02
.03
.04
.06
.08
.10
.11
.02
.02
.03
.04
.06
.07
.09
.11
Return or
Outside Air
Damper
.02
.02
.03
.04
.06
.07
.09
.11
.12
.04
.05
.09
.13
.19
.25
.27
.03
.04
.06
.08
.11
.15
.19
.22
.05
.06
.08
.11
.15
.19
.23
.28
.04
.05
.08
.13
.19
.25
.28
.05
.08
.13
.19
.25
.33
.38
.06
.07
.10
.15
.20
.26
.33
.39
Performance
Data
Table PD-17 – Standard or High Efficiency Indoor Make-Up Air Handler – Arrangement G, K – 500-800 MBh – Accessory Pressure Loss
Capacity
50
60
70
80
CFM
2,300
2,500
3,000
3,500
4,000
4,500
5,000
5,500
6,000
2,700
3,000
4,000
5,000
6,000
7,000
7,400
3,200
4,000
5,000
6,000
7,000
8,000
8,600
3,700
4,000
5,000
6,000
7,000
8,000
9,000
9.800
Rainhood
with
Screen
Mstr. Elim.
.04
.05
.04
.06
.06
.08
.09
.11
.11
.15
.14
.19
.17
.23
.21
.28
.25
.33
.03
.04
.04
.05
.06
.09
.10
.13
.14
.19
.20
.26
.22
.29
.04
.05
.06
.09
.10
.13
.14
.19
.20
.26
.26
.34
.30
.40
.04
.06
.05
.07
.08
.11
.11
.15
.16
.21
.20
.27
.26
.35
.31
.41
Pressure Loss (Inches of Water)
Filters
Throwaway
Washable
2”
1”
2”
.04
<.01
<.01
.05
<.01
.01
.06
.01
.02
.08
.01
.02
.09
.02
.03
.11
.02
.03
.12
.03
.04
.14
.04
.05
.16
.04
.06
.03
<.01
<.01
.03
<.01
<.01
.05
<.01
.01
.06
.01
.02
.08
.02
.02
.10
.02
.03
.11
.02
.03
.03
<.01
<.01
.05
<.01
.01
.06
.01
.02
.08
.02
.02
.10
.02
.03
.12
.03
.04
.13
.03
.05
.03
<.01
<.01
.04
<.01
<.01
.05
<.01
.01
.07
.01
.02
.08
.02
.02
.10
.02
.03
.12
.03
.04
.13
.03
.05
Pleated
1”
.05
.05
.07
.09
.12
.14
.17
.20
.23
.03
.03
.05
.08
.10
.13
.15
.04
.05
.08
.10
.13
.17
.19
.04
.04
.06
.08
.10
.13
.16
.18
2”
.02
.03
.04
.05
.07
.08
.10
.12
.14
.01
.02
.03
.04
.06
.08
.08
.02
.03
.04
.06
.08
.10
.11
.02
.02
.03
.04
.06
.07
.09
.11
Return or
Outside Air
Damper
.05
.06
.08
.11
.15
.19
.23
.28
.33
.04
.05
.08
.13
.19
.25
.28
.05
.08
.13
.19
.25
.33
.38
.06
.07
.10
.15
.20
.26
.33
.39
Table PD-18 – Standard or High Efficiency Indoor Make-Up Air Handler – Arrangement G – 1200 MBh – Accessory Pressure Loss
Capacity
12
CFM
4,500
5,000
6,000
7,000
8,000
9,000
9,800
Rainhood
with
Screen
Mstr. Elim.
.06
.09
.08
.11
.11
.15
.16
.21
.20
.27
.26
.35
.31
.41
Pressure Loss (Inches of Water)
Filters
Throwaway
Washable
2”
1”
2”
.05
<.01
<.01
.05
<.01
.01
.07
.01
.02
.08
.02
.02
.10
.02
.03
.12
.03
.04
.13
.03
.05
35
Pleated
1”
.05
.06
.08
.10
.13
.16
.18
2”
.03
.03
.04
.06
.07
.09
.11
Return or
Outside Air
Damper
.08
.10
.15
.20
.26
.33
.39
Performance
Data
Table PD-19 – Evaporative Cooling Performance Data and Pressure Drop – Rooftop Arrangement D
CFM
(cu. m/s) (cu. m/s)
Unit Size
Min.
Max.
10, 15
800
4,500
(0.378)
(2.124)
20, 25, 50
1,600
5,500
(0.755)
(2.596)
30, 35, 60, 70 2,400
8,500
(1.133)
(4.012)
40, 80
3,200
8,500
(1.510)
(4.012)
Efficiency
Range
Min.
Max.
78
88
8” Saturation
Efficiency
Range
Min.
Max.
89
92
77
88
88
92
77
86
88
92
77
86
87
92
12” Saturation
8” or 12” Deep Media
Face Area
Size
Ft.2 (m2)
In. (mm)
7.01
31 x 32 9/16
(0.65)
(787) (827)
9.38
31 x 43 9/16
(0.87)
(787) (1106)
11.75
31 x 54 9/16
(1.09)
(787) (1386)
12.92
31 x 60
(1.20)
(787) (1524)
Pressure Drop
in. of Water
(KPa)
(KPa)
Min.
Max.
0.03
0.23
(0.01)
(0.06)
0.03
0.20
(0.01)
(0.05)
0.05
0.30
(0.01)
(0.07)
0.07
0.28
(0.02)
(0.07)
Note:
1. These weights are for evaporative cooler only.
CELdek® Evaporative Media
The Trane Evaporative Cooler uses
high efficiency CELdek® media.
CELdek® is made from a special
cellulose paper, impregnated with
insoluble anti-rot salts and rigidifying
saturants. The cross fluted design of
the pads induces high-turbulent
mixing of air and water for optimum
heat and moisture transfer. The Trane
evaporative coolers are standard with
eight-inch deep media which produce
high efficiency and high face
velocities, along with a two-inch
distribution pad to disperses the water
evenly over the pads. We offer an
optional 12-inch deep media (see chart
at right for efficiencies). Sump motor
hp is 1/50th.
Chart PD-1 – Evaporative Cooler Efficiency/A.P.D. Chart
36
(1)
“A” Unit Shipping
Width
Wt.
In. (mm) lb. (kg)
32 3/4
137
(832)
(62)
43 3/4
166
(1111)
(75)
54 3/4
192
(1391)
(87)
1
60 /4
206
(1530)
(93)
(1)
Operating
Wt.
lb. (kg)
301
(136)
386
(175)
468
(212)
509
(231)
Electrical
Data
Indoor Make-Up Air Handler Standard or High Efficiency – Motor Electrical Data
Voltage
115/60/1 ODP
208/60/1 ODP
230/60/1 ODP
208/60/3 ODP
230/60/3 ODP
460/60/3 ODP
575/60/3 ODP
115/60/1 TE
208/60/1 TE
230/60/1 TE
208/60/3 TE
230/60/3 TE
460/60/3 TE
575/60/3 TE
115/60/1 HEODP
208/60/1 HEODP
230/60/1 HEODP
208/60/3 HEODP
230/60/3 HEODP
460/60/3 HEODP
575/60/3 HEODP
115/60/1 HETE
208/60/1 HETE
230/60/1 HETE
208/60/3 HETE
230/60/3 HETE
460/60/3 HETE
575/60/3 HETE
208/60/3 2S1W
230/60/3 2S1W
460/60/3 2S1W
575/60/3 2S1W
115/60/1 2S2W
208/60/1 2S2W
230/60/1 2S2W
208/60/3 2S2W
230/60/3 2S2W
460/60/3 2S2W
575/60/3 2S2W
1
/2 HP
7.2
4.3
4.3
2.8
2.8
1.4
1.1
9.0
3.9
4.5
2.1
2.2
1.1
0.9
5.2
2.8
2.6
1.8
1.6
0.8
NA
5.5
NA
2.8
NA
4.6
2.3
NA
NA
NA
NA
NA
9.2/6.0
NA
4.6/3.0
2.4/1.6
2.1/1.4
1.1/0.7
NA
3
/4 HP
10.9
6.0
5.5
2.6
2.6
1.3
1.4
11.4
4.5
5.7
2.8
2.8
1.4
1.3
6.4
4.2
5.2
2.5
2.3
1.2
NA
7.6
NA
3.8
NA
6.3
3.2
NA
NA
NA
NA
NA
9.2/4.6
5.0/2.5
4.6/2.3
3.0/1.9
2.7/1.7
1.3/0.9
NA
1 HP
13.4
6.7
6.7
3.2
3.2
1.6
1.5
13.6
6.8
6.8
3.4
3.6
1.8
1.7
9.2
NA
4.6
3.6
2.8
1.4
1.1
9.2
NA
4.6
3.2
3.0
1.5
1.1
3.0/1.0
3.0/1.0
1.5/0.5
NA
11.9/6.9
6.3/3.0
6.0/3.6
3.4/2.0
3.2/2.0
1.5/1.0
NA
1 1/2 HP
18.0
9.3
9.0
4.8
4.8
2.4
1.9
17.6
8.0
8.8
4.8
4.9
2.4
1.9
12.5
NA
6.3
5.0
3.8
1.9
1.8
14.0
NA
7.0
4.6
4.2
2..1
1.8
4.4/1.8
4.4/1.8
2.2/1.9
NA
NA
NA
NA
5.0/2.6
4.8/2.9
2.3/1.3
NA
2 HP
26.0
11.5
13.0
6.2
6.2
3.1
2.5
24.6
12.3
12.3
6.4
6.4
3.2
2.6
16.4
NA
8.2
6.7
5.4
2.7
2.3
19.2
NA
9.6
6.2
5.8
2.9
2.4
6.2/3.0
5.9/2.9
3.1/1.3
NA
NA
NA
NA
6.5/3.5
6.3/3.5
3.0/1.7
NA
Notes:
1. ODP = Open Drip Proof
2. TE = Totally enclosed
3. HEODP = High Efficiency Open Drip Proof
4. HETE = High Efficiency Totally Enclosed
5. 2S1W = Two Speed One Winding
6. 2S2W = Two Speed Two Winding
7. NA = Not Available
FLA based on NEC Ratings
37
3 HP
33.0
16.5
16.5
8.4
8.4
4.2
3.6
34.0
17.0
17.0
9.4
9.2
4.6
3.6
NA
NA
NA
9.2
8.0
4.0
3.2
NA
NA
NA
8.8
8.0
4.0
3.2
9.0/3.4
8.0/3.3
3.8/1.6
NA
NA
NA
NA
9.3/4.9
8.5/4.6
4.6/2.7
NA
5 HP
NA
NA
NA
12.2
12.2
6.1
5.3
NA
NA
NA
14.0
13.0
6.5
5.1
NA
NA
NA
14.7
12.8
6.4
5.2
NA
NA
NA
14.7
12.0
6.0
4.8
15.0/6.0
14.0/6.2
6.8/2.8
NA
NA
NA
NA
NA
NA
NA
NA
7 1/2 HP
NA
NA
NA
24.0
21.6
10.8
8.6
NA
NA
NA
21.8
20.4
10.2
7.6
NA
NA
NA
22.1
19.2
9.6
7.7
NA
NA
NA
21.4
18.8
9.4
7.5
21.0/7.5
19.5/7.5
10.0/4.0
NA
NA
NA
NA
20.0/11.0
19.0/10.0
9.7/5.5
NA
10 HP
NA
NA
NA
28.0
26.6
13.3
10.6
NA
NA
NA
28.7
26.4
13.2
9.6
NA
NA
NA
29.0
25.2
25.2
10.1
NA
NA
NA
29.0
25.2
12.6
10.2
29.0/9.6
25.0/9.3
12.0/4.3
NA
NA
NA
NA
27.0/14.0
25.0/12.5
12.2/7.0
NA
15 HP
NA
NA
NA
44.9
40.6
20.3
15.6
NA
NA
NA
42.6
28.4
19.2
14.4
NA
NA
NA
40.0
36.0
18.0
14.5
NA
NA
NA
41.2
37.0
18.5
14.9
NA
NA
18.0/6.0
NA
NA
NA
NA
NA
NA
NA
NA
Controls
Pilot Control
Intermittent pilot ignition is standard on
all outdoor units. Intermittent pilot
ignition contains a solid-state ignition
control system that ignites the pilot by
spark for each cycle of operation. When
the pilot flame is proven, the main
burner valve opens to allow gas flow to
the burners. Both the pilot and burners
are extinguished during the off cycle.
Energy savings will be realized using
this system as the pilot is extinguished
in the off cycle.
Air Inlet Configuration
The air inlet configuration defines the
entering air opening for the gas heating
units. This selection does not include
dampers and must match the required
opening for the air control and damper
arrangement. A horizontal return air
feature is offered on air inlet
configurations 3 and 4.
Air Inlet Configuration
1
3
4
See
Note
Below
Note: Horizontal outside air over return
air. Specify air inlet configuration 4 and
then select miscellaneous option “D”
for horizontal return.
Damper Options
Dampers shall be of the opposed
blade type, constructed of galvanized
steel with neoprene nylon bushings,
blades to be mechanically interlocked.
Optional low leak dampers shall be of
the opposed blade type, construction
of galvanized steel with neoprene
nylon bushings and vinyl blade edge
seals, blades to be mechanically
interlocked.
Outside Air or Return Air
Two-Position Motor/Spring Return
Units with outside air or return air only
shall be provided with a damper, twoposition spring return damper motor
and controls. The motor shall power
the damper fully open when the unit is
on and fully closed when the unit is off.
Outside Air/Return Air
Two-Position Spring Return
A two-position spring return motor
with interlocked outside and return air
dampers shall be provided. The motor
shall power either the outside air
damper fully open and the return air
damper fully closed or the outside air
damper fully closed and the return air
damper fully open in response to an
outside air temperature sensor. When
the unit is off, the motor will drive the
outside air damper fully closed and the
return air damper fully open.
Outside Air/Return Air Modulating
Motor with Mixed Air Control/
Minimum Position Potentiometer/
Spring Return
A modulating motor with interlocked
outside and return air dampers shall be
provided. The motor shall modulate the
position of the outside and return air
dampers in response to a thermostatic
controller located in the mixed air
stream. Units shall also be provided
with a minimum position
potentiometer for minimum outside air
damper position.
The spring return feature drives the
outside air damper fully closed and the
return air damper fully open when the
unit is off.
Outside Air/Return Air Modulating
Motor with Mixed Air Temperature
Control/Spring Return
Modulating motor with interlocked
outside and return air dampers shall be
provided. The motor shall modulate the
position of the outside and return air
dampers in response to a thermostatic
controller located in the mixed air
stream.
The spring return feature drives the
outside air damper fully closed and the
return air damper fully open when the
unit is off.
38
Outside Air/Return Air Modulating
Motor with Minimum Position
Potentiometer/Spring Return
A modulating motor with interlocked
outside and return air dampers shall be
provided. The motor shall position the
outside and return air dampers in
response to a manually set
potentiometer.
The spring return feature drives the
outside air damper fully closed and the
return air damper fully open when the
unit is off.
Outside Air/Return Air Modulating
Motor with Dry Bulb/ Mixed Air
Temperature Control and Minimum
Position Potentiometer/Spring Return
A modulating motor with interlocked
outside and return air dampers shall be
provided. The motor shall modulate the
position of the outside and return air
dampers in response to a thermostatic
controller and dry bulb thermostat
located in the mixed air stream. Units
shall also be provided with a minimum
position potentiometer for minimum
outside air damper position. The spring
return feature drives the outside air
damper fully open and the return air
damper fully closed when the unit is
off.
Outside Air/Return Air Modulating
Motor with Enthalpy Controlled
Economizer/Spring Return
A modulating motor with spring return
and interlocked outside and return air
dampers shall be provided. The motor
shall modulate the position of the
outside and return air dampers in
response to an enthalpy controlled
economizer. When the unit is off, the
motor will drive the outside air damper
fully closed and the return air damper
fully open.
Controls
Outside Air/Return Air Modulating
Motor with Space Pressure Controller
A modulating motor with spring return
and interlocked outside and return air
dampers shall be provided. The motor
shall modulate the position of the
outside and return air dampers in
response to a pressure sensor located
in the building. When the unit is off, the
motor will drive the outside air damper
fully closed and the return air damper
fully open.
Outside Air/Return Air Modulating
Motor with S-350P Proportional Mixed
Air Control/Spring Return
A modulating motor with spring return
and interlocked outside and return air
dampers shall be provided. The motor
shall modulate the position of the
outside and return air dampers in
response to a solid-state mixed air
sensor and S-350 proportional
controller.
When the unit is off, the motor will
drive the outside air damper fully
closed and the return air damper fully
open.
Outside Air/Return Air Modulating
Motor with External 4-20 mA or
0-10 VDC Analog Input/Spring Return
A modulating motor interlocked with
outside and return air dampers shall be
provided. The motor shall modulate the
position of the outside and return air
dampers in response to a 4-10 mA or 010 VDC signal supplied by an external
DDC controller. The spring return
feature drives the outside air damper
fully closed and the return air damper
fully open when the unit is shut down.
ASHRAE Cycle I (Outside/Return Air
Two Position with Warm-Up Stat/
Spring Return)
A two-position spring return motor
with interlocked outside and return air
dampers shall be provided. The motor
shall power the outside air damper
fully open after a warm-up period
determined by a minimum supply air
temperature sensor when the unit is
on, and fully closed when the unit is off.
39
ASHRAE Cycle II (Outside Air/Return
Air Modulating Motor with Warm-Up
Stat/Mixed Air Temperature Controller/
Minimum Position Potentiometer/
Spring Return)
A modulating motor with interlocked
outside and return air dampers shall be
provided. The motor shall modulate the
position of the outside and return air
dampers in response to a thermostatic
controller located in the mixed air
stream after a warm-up period
determined by a minimum supply air
temperature sensor. Units shall also be
provided with a minimum position
potentiometer for minimum outside air
damper position.
When the unit is off, the motor will
drive the outside air damper full closed
and the return air damper full open.
ASHRAE CYCLE III (Outside Air/ Return
Air Modulating Motor with Warm-Up
Thermostat/Mixed Air Temperature
Controller/Spring Return)
A modulating motor with spring return
and interlocked outside and return air
dampers shall be provided. The motor
shall modulate the position of the
outside and return air dampers in
response to a thermostatic controller
located in the mixed air stream after a
warm up period determined by a
minimum supply air temperature
sensor. Units shall also be provided
with a minimum position
potentiometer for minimum outside air
damper position.
When the unit is off, the motor will
drive the outside air damper fully
closed and the return air damper fully
open.
Manual Dampers
Units with outside air and return air
shall be provided with manually set
outside and return air dampers.
Controls
Gas Control Reference
1 Stage
2 Stage
Modulation
Single Furnace
Capacities “10-40”
1 Stage
2 Stage
4 Stage
Modulation
Dual Furnace
Capacities “50-80”
Gas Controls
Single-Stage Control
Gas heating units are provided with an
automatic single-stage gas valve as
standard. This valve is an on/off type
control, typically activated by a low
voltage single-stage thermostat
(thermostat not included).
Two-Stage Gas Valve
This gas valve provides two stages of
heat. Ignition is at low fire (one half of
the unit’s full rated input). Requires the
use of an optional two-stage
thermostat.
Hydraulic Modulating Gas Valve
Provides modulated heat output.
Ignition is at low fire (one half of the
unit’s full rated input), and a discharge
air temperature sensing bulb located in
the air stream shall modulate the gas
input from 40 percent to 100 percent of
rated input. Provided with an automatic
electric valve in series with the
hydraulic valve which cycles the unit in
response to an optional low voltage
single-stage thermostat.
Hydraulic Modulating Gas Valve
with Bypass
Provides modulated heat output.
Ignition is at low fire (one half of the
unit’s full rated input), and a discharge
temperature sensing bulb located in
the air stream shall modulate the gas
input from 40 percent to 100 percent
rated input. Provided with an automatic
electric valve in series with the
hydraulic valve which cycles the unit.
An additional electric valve in parallel
bypasses the hydraulic modulating
valve, overriding the discharge
temperature sensing bulb, allowing full
fire. Requires the use of an optional
thermostat to control the electric valve.
1 Stage
2 Stage
3 Stage
6 Stage
Modulation
Triple Furnace
Capacity “12”
Electronic Modulating — Room or
Duct Stat Control
Provides modulated heat output. An
automatic valve in series with the
modulating valve shall be provided to
cycle the unit. Ignition is at full fire
(100 percent input), and modulates the
gas input from 100 percent to 40
percent rated input.
Available for use with a room
thermostat or duct thermostat with a
remote setpoint adjustment. A duct
thermostat is available with an optional
override room thermostat which
causes the unit to go to full fire when
the room temperature falls below the
override room thermostat’s setpoint.
Electronic Modulating — 4-20 mA/
0-10 VDC Input
Provides modulated heat output.
Ignition is at full fire (100 percent input),
and modulates the gas input from 100
percent to 40 percent rated input. The
modulating gas valve shall operate in
response to a 4-20 mA or a 0-10 VDC
input from an external DDC control.
When “furnace one only” is specified
on double and triple furnaces,
additional furnace sections will have
single-stage on-off control.
Discharge Air Control with Outside
Air Reset
Unit provided with factory-mounted
discharge air controller, discharge air
sensor, outdoor air reset, summer/
winter thermostat and velocity
pressure switch. The outdoor air reset
range is from 10 F to 60 F. Full reset
occurs at 10 F outside air temperature.
There is a straight line relationship
between outside air temperature and
reset. Therefore, at 60 F outside air
temperature, no reset will occur. The
amount of reset is adjustable from 20 F
to 50 F.
40
A discharge air controller provides a
two-minute delay between successive
on and off stages. A summer/winter
thermostat locks out heating when
outside air temperature is above 55 F.
The velocity pressure switch is
provided for protection against high
temperatures at low airflows. Available
in two-stage (half of the unit’s full rated
input-single furnace units only), threestage (33 percent of the unit’s full rated
input) and four-stage (25 percent of the
unit’s full rated input). Three and fourstage is available on double and triple
furnace units only.
S-350 Modular Electronic Control
System Two-Stage
The basic system utilizes a controller
module with discharge air sensor,
setpoint and one-stage output, a stage
module with differential setpoint and
one-stage output and a display module
with LCD display for temperature
readout. The system stages the unit’s
rate of fire based upon sensed
discharge air temperature, setpoint
setting and differential setting between
stages. Provided as a two-stage (all
furnaces), three and four-stage (double
and triple furnaces only) and six-stage
(triple furnace only).
Dimensional
Data
Standard Blower Module for Arrangements B, D
Unit Sizes 10-80 (100-800 MBh)
Model
10/15
20/25/50
30/35
60/70
40/80
A
32 7/8”
(835)
43 7/8”
(1114)
54 7/8”
(1394)
60 3/4”
(1534)
B
15 9/16”
(395)
23 13/16”
(605)
34 13/16”
(884)
45 13/16”
(1164)
J
24”
(610)
35”
(889)
46”
(1168)
51 1/2”
(1308)
STANDARD BLOWER MODULE
Unit Sizes 10-80
(Left Hand Service Access Shown)
Note: The dimensions shown do not include base skid rail.
DIMENSIONS ARE IN INCHES, DIMENSIONS IN
PARENTHESES ARE IN MILLIMETERS.
41
Dimensional
Data
Detail Drawing
High CFM Blower Module for Arrangement G
Unit Sizes 10-12 (100-1200 MBh)
100 and 150 MBh Units Not Available on Arrangement G
Model
10/15*
20/25/50
30/35
60/70
40/80/12
A
32 7/8”
(835)
43 7/8”
(1114)
54 7/8”
(1394)
60 3/8”
(1534)
B
15 9/16”
(395)
23 13/16”
(605)
34 13/16”
(884)
45 13/16”
(1164)
∆J
24”
(610)
35”
(889)
46”
(1168)
51 1/2”
(1308)
HIGH CFM BLOWER MODULE
*For Cooling Arrangements Only
(Left Hand Service Access Shown)
Note: The dimensions shown do not include base skid rail.
DIMENSIONS ARE IN INCHES, DIMENSIONS IN
PARENTHESES ARE IN MILLIMETERS.
42
Dimensional
Data
Over/Under Air Intake without Hood
Arrangements B, D, G, K
Unit Sizes 10-12 (100-1200 MBh)
Model
10/15
E Dimension
27 3/4”
(705)
38 3/4”
(984)
49 3/4”
(1264)
55 1/4”
(1403)
20/25/50
30/35
60/70
40/80/12
DIMENSIONS ARE IN INCHES, DIMENSIONS IN
PARENTHESES ARE IN MILLIMETERS.
43
Dimensional
Data
Coil Module
Arrangement K
Unit Sizes 10-80 (100-800 MBh)
Model
10/15
20/25/50
30/35
60/70
40/80
A
32 7/8”
(835)
43 7/8”
(1114)
54 7/8”
(1394)
60 3/8”
(1534)
DIMENSIONS ARE IN INCHES, DIMENSIONS
IN PARENTHESES ARE IN MILLIMETERS.
Unit Size
10/15
20/25/50
30/35/60/70
40/80
“L” Inside Max.
Cabinet Opening
32 1/4” (794)
42 1/4” (1073)
53 1/4” (1353)
58 3/4” (1492)
Side Opening of Cooling Module
• The coil section drain pan connection is 3/4 inch NPT pipe thread. It is a female fitting that
just protrudes outside of the unit base rail. It is located on the service side of the unit.
• The drain pan is constructed of stainless steel, including the fitting. It is sloped towards the
center of the pan and level across the width of the unit.
• P-trap required external to the unit provided by others.
44
Dimensional
Data
Evaporative Cooler Module
Arrangement D
Unit Sizes 10-80 (100-800 MBh)
EVAPORATIVE COOLER MODULE
Models 10/80
Model
10/15
A
32 7/8”
(835)
43 7/8”
(1114)
54 7/8”
(1394)
60 3/8”
(1534)
20/25/50
30/35
60/70
40/80
DIMENSIONS ARE IN INCHES, DIMENSIONS IN
PARENTHESES ARE IN MILLIMETERS.
45
Dimensional
Data
Indoor Make-Up Air Handler with Standard Blower – Arrangement B
Models GSAA, GSBA – 10, 15, 20, 25, 30, 35, 40 (100-400 MBh)
Single Furnace
GRAVITY VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
10
15
20
25
30
35
40
A
32 7/8
(835)
32 7/8
(835)
43 7/8
(1114)
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
15 9/16
(395)
18 5/16
(465)
23 13/16
(605)
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
1/2
LP
1/2
1/2
1/2
1/2
1/2
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
16 3/8
(416)
20 1/2
(521)
23 1/2
(597)
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
“J” is an outside dimension for return air dampers.
“S” Dimension Legend: R = Round; OV = Oval.
46
G
31 1/16
(789)
31 1/16
(789)
42 1/16
(1068)
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
H
40 5/8
(1032)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
J
24
(610)
24
(610)
35
(889)
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
M
21 1/4
(540)
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
21 1/4
(540)
S
6R
(152)
7R
(178)
8R
(203)
8R
(203)
10 OV
(254)
10 OV
(254)
12 OV
(305)
Dimensional
Data
Indoor Make-Up Air Handler with Standard Blower and Evaporative Cooler – Arrangement D
Models GSAA, GSBA – 10, 15, 20, 25, 30, 35, 40 (100-400 MBh)
Single Furnace
GRAVITY VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
10
15
20
25
30
35
40
A
32 7/8
(835)
32 7/8
(835)
43 7/8
(1114)
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
15 9/16
(395)
18 5/16
(465)
23 13/16
(605)
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
1/2
LP
1/2
1/2
1/2
1/2
1/2
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
16 3/8
(416)
20 1/2
(521)
23 1/2
(597)
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
“J” is an outside dimension for return air dampers.
“S” Dimension Legend: R = Round; OV = Oval.
47
G
31 1/16
(789)
31 1/16
(789)
42 1/16
(1068)
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
H
40 5/8
(1032)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
J
24
(610)
24
(610)
35
(889)
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
M
21 1/4
(540)
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
21 1/4
(540)
S
6R
(152)
7R
(178)
8R
(203)
8R
(203)
10 OV
(254)
10 OV
(254)
12 OV
(305)
Dimensional
Data
Indoor Make-Up Air Handler with High Cfm Blower – Arrangement G
Models GSAA, GSBA – 20, 25, 30, 35, 40 (200-400 MBh)
Single Furnace
GRAVITY VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
20
25
30
35
40
A
43 7/8
(1114)
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
23 13/16
(605)
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
1/2
LP
1/2
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
23 1/2
(597)
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
“J” is an outside dimension for return air dampers.
“S” Dimension Legend: R = Round; OV = Oval.
48
G
42 1/16
(1068)
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
H
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
J
35
(889)
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
M
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
21 1/4
(540)
S
8R
(203)
8R
(203)
10 OV
(254)
10 OV
(254)
12 OV
(305)
Dimensional
Data
Indoor Make-Up Air Handler with High Cfm Blower and Cooling Coil Section – Arrangement K
Models GSAA, GSBA – 10, 15, 20, 25, 30, 35, 40 (100-400 MBh)
GRAVITY VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
10
15
20
25
30
35
40
A
32 7/8
(835)
32 7/8
(835)
43 7/8
(1114)
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
15 9/16
(395)
18 5/16
(465)
23 13/16
(605)
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
1/2
LP
1/2
1/2
1/2
1/2
1/2
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
16 3/8
(416)
20 1/2
(521)
23 1/2
(597)
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
“J” is an outside dimension for return air dampers.
“S” Dimension Legend: R = Round; OV = Oval.
49
G
31 1/16
(789)
31 1/16
(789)
42 1/16
(1068)
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
H
40 5/8
(1032)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
J
24
(610)
24
(610)
35
(889)
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
M
21 1/4
(540)
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
21 1/4
(540)
S
6R
(152)
7R
(178)
8R
(203)
8R
(203)
10 OV
(254)
10 OV
(254)
12 OV
(305)
Dimensional
Data
Indoor Duct Furnace – Arrangement A
Models GDAA, GDBA – 50, 60, 70, 80 (500-800 MBh)
Double Furnace
GRAVITY VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Capacity
50
60
70
80
A
31 5/8
(803)
37 1/8
(943)
42 5/8
(1083)
48 1/8
(1222)
B
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
F*
37 5/8
(956)
43 18
(1095)
48 5/8
(1235)
54 1/8
(1375)
G
41 1/8
(1045)
52 1/8
(1324)
52 1/8
(1324)
57 5/8
(1464)
M
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
21 1/4
(540)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
“S” Dimension Legend: R = Round; OV = Oval.
Gas inlet sizes: Natural Gas = 3/4” Dia. LP Gas = 1/2” or 3/4” Dia.
50
S
8R
(203)
10 OV
(254)
10 OV
(254)
12 OV
(305)
Dimensional
Data
Indoor Make-Up Air Handler with Standard Blower – Arrangement B
Models GSAA, GSBA – 50, 60, 70, 80 (500-800 MBh)
Double Furnace
GRAVITY VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
50
60
70
80
A
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
3/4
LP
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
“J” is an outside dimension for return air dampers.
“S” Dimension Legend: R = Round; OV = Oval.
51
G
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
H
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
J
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
M
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
21 1/4
(540)
S
8R
(203)
10 OV
(254)
10 OV
(254)
12 OV
(305)
Dimensional
Data
Indoor Make-Up Air Handler with Standard Blower and Evaporative Cooler – Arrangement D
Models GSAA, GSBA – 50, 60, 70, 80 (500-800 MBh)
Double Furnace
GRAVITY VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
50
60
70
80
A
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
3/4
LP
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
“J” is an outside dimension for return air dampers.
“S” Dimension Legend: R = Round; OV = Oval.
52
G
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
H
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
J
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
M
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
21 1/4
(540)
S
8R
(203)
10 OV
(254)
10 OV
(254)
12 OV
(305)
Dimensional
Data
Indoor Make-Up Air Handler with High Cfm Blower – Arrangement G
Models GSAA, GSBA – 50, 60, 70, 80 (500-800 MBh)
Double Furnace
GRAVITY VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
50
60
70
80
A
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
3/4
LP
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
“J” is an outside dimension for return air dampers.
“S” Dimension Legend: R = Round; OV = Oval.
53
G
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
H
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
J
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
M
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
21 1/4
(540)
S
8R
(203)
10 OV
(254)
10 OV
(254)
12 OV
(305)
Dimensional
Data
Indoor Make-Up Air Handler with High Cfm Blower and Cooling Coil Section – Arrangement K
Models GSAA, GSBA – 50, 60, 70, 80 (500-800 MBh)
Double Furnace
GRAVITY VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
50
60
70
80
A
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
3/4
LP
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
“J” is an outside dimension for return air dampers.
“S” Dimension Legend: R = Round; OV = Oval.
54
G
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
H
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
45 5/8
(1159)
J
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
M
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
21 1/4
(540)
S
8R
(203)
10 OV
(254)
10 OV
(254)
12 OV
(305)
Dimensional
Data
Indoor Duct Furnace – Arrangement A
Models GDAA, GDBA – 12 (1200 MBh)
Triple Furnace
GRAVITY VENT
(Left Hand Unit Shown)
Indoor Make-Up Air Handler with High Cfm Blower – Arrangement G
Models GSAA, GSBA – 12 (1200 MBh)
Triple Furnace
GRAVITY VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
55
Dimensional
Data
High Efficiency Indoor Make-Up Air Handler with Standard Blower – Arrangement B
Models GGAA, GGBA – 10, 15, 20, 25, 30, 35, 40 (100-400 MBh)
Single Furnace
POWER VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
10
15
20
25
30
35
40
A
32 7/8
(835)
32 7/8
(835)
43 7/8
(1114)
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
15 9/16
(395)
18 5/16
(465)
23 13/16
(605)
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
1/2
LP
1/2
1/2
1/2
1/2
1/2
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
16 3/8
(416)
20 1/2
(521)
23 1/2
(597)
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
G
31 1/16
(789)
31 1/16
(789)
42 1/16
(1068)
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
J
24
(610)
24
(610)
35
(889)
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
**V Dia.
**4
(102)
**4
(102)
5
(127)
5
(127)
**6
(152)
**6
(152)
**6
(152)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
** “V Dia.” = The Flue Opening; Capacities 10 & 15 will require a field installed 5” to 4” Dia. reducer. Capacities 30/35/40 will require a field installed 5” to 6” Dia.
increaser that will be supplied with the unit.
“J” is an outside dimension for outside or return air dampers.
56
Dimensional
Data
High Efficiency Indoor Make-Up Air Handler with Standard Blower and Evaporative Cooler – Arrangement D
Models GGAA, GGBA – 10, 15, 20, 25, 30, 35, 40 (100-400 MBh)
Single Furnace
POWER VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
10
15
20
25
30
35
40
A
32 7/8
(835)
32 7/8
(835)
43 7/8
(1114)
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
15 9/16
(395)
18 5/16
(465)
23 13/16
(605)
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
1/2
LP
1/2
1/2
1/2
1/2
1/2
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
16 3/8
(416)
20 1/2
(521)
23 1/2
(597)
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
G
31 1/16
(789)
31 1/16
(789)
42 1/16
(1068)
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
J
24
(610)
24
(610)
35
(889)
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
**V Dia.
**4
(102)
**4
(102)
5
(127)
5
(127)
**6
(152)
**6
(152)
**6
(152)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
** “V Dia.” = The Flue Opening; Capacities 10 & 15 will require a field installed 5” to 4” Dia. reducer. Capacities 30/35/40 will require a field installed 5” to 6” Dia.
increaser that will be supplied with the unit.
“J” is an outside dimension for outside or return air dampers.
57
Dimensional
Data
High Efficiency Indoor Make-Up Air Handler with High Cfm Blower – Arrangement G
Models GGAA, GGBA – 20, 25, 30, 35, 40 (200-400 MBh)
Single Furnace
POWER VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
20
25
30
35
40
A
43 7/8
(1114)
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
23 13/16
(605)
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
1/2
LP
1/2
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
23 1/2
(597)
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
G
42 1/16
(1068)
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
J
35
(889)
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
** “V Dia.” = The Flue Opening; Capacities 30/35/40 will require a field installed 5” to 6” Dia. increaser that will be supplied with the unit.
“J” is an outside dimension for outside or return air dampers.
58
**V Dia.
5
(127)
5
(127)
**6
(152)
**6
(152)
**6
(152)
Dimensional
Data
High Efficiency Indoor Make-Up Air Handler with High Cfm Blower and Cooling Coil Section – Arrangement K
Models GGAA, GGBA – 10, 15, 20, 25, 30, 35, 40 (100-400 MBh)
POWER VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
10
15
20
25
30
35
40
A
32 7/8
(835)
32 7/8
(835)
43 7/8
(1114)
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
15 9/16
(395)
18 5/16
(465)
23 13/16
(605)
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
1/2
LP
1/2
1/2
1/2
1/2
1/2
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
16 3/8
(416)
20 1/2
(521)
23 1/2
(597)
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
G
31 1/16
(789)
31 1/16
(789)
42 1/16
(1068)
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
J
24
(610)
24
(610)
35
(889)
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
**V Dia.
**4
(102)
**4
(102)
5
(127)
5
(127)
**6
(152)
**6
(152)
**6
(152)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
** “V Dia.” = The Flue Opening; Capacities 10 & 15 will require a field installed 5” to 4” Dia. reducer. Capacities 30/35/40 will require a field installed 5” to 6” Dia.
increaser that will be supplied with the unit.
“J” is an outside dimension for outside or return air dampers.
59
Dimensional
Data
High Efficiency Indoor Duct Furnace – Arrangement A
Models GGAA, GGBA – 50, 60, 70, 80 (500-800 MBh)
Double Furnace
POWER VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Capacity
50
60
70
80
A
31 5/8
(803)
37 1/8
(943)
42 5/8
(1083)
48 1/8
(1222)
B
20 5/16
(745)
34 3/16
(884)
40 5/16
(1024)
45 13/16
(1164)
F*
37 5/8
(956)
43 18
(1095)
48 5/8
(1235)
54 1/8
(1375)
G
41 1/8
(1045)
52 1/8
(1324)
52 1/8
(1324)
57 5/8
(1464)
M
20 1/4
(514)
20 1/4
(514)
20 1/4
(514)
21 1/4
(540)
V Dia.**
5
(127)
6
(152)
6
(152)
6
(152)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
**“V” Dia. = Flue Opening (ME - Power Vent Units Only). The 5” to 6” increaser adapter is supplied by
the manufacturer for unit capacities 60, 70 and 80.
Gas inlet sizes: Natural Gas = 3/4” Dia. LP Gas = 1/2” or 3/4” Dia.
60
Dimensional
Data
High Efficiency Indoor Make-Up Air Handler with Standard Blower – Arrangement B
Models GGAA, GGBA – 50, 60, 70, 80 (500-800 MBh)
Double Furnace
POWER VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
50
60
70
80
A
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
3/4
LP
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
G
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
** “V Dia.” = The Flue Opening; Capacities 60/70/80 will require 5” to 6” increaser on each furnace that will be supplied with the unit.
“J” is an outside dimension for outside or return air dampers.
61
J
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
**V Dia.
5
(127)
**6
(152)
**6
(152)
**6
(152)
Dimensional
Data
High Efficiency Indoor Make-Up Air Handler with Standard Blower and Evaporative Cooler – Arrangement D
Models GGAA, GGBA – 50, 60, 70, 80 (500-800 MBh)
Double Furnace
POWER VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
50
60
70
80
A
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
3/4
LP
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
G
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
** “V Dia.” = The Flue Opening; Capacities 60/70/80 will require 5” to 6” increaser on each furnace that will be supplied with the unit.
“J” is an outside dimension for outside or return air dampers.
62
J
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
**V Dia.
5
(127)
**6
(152)
**6
(152)
**6
(152)
Dimensional
Data
High Efficiency Indoor Make-Up Air Handler with High Cfm Blower – Arrangement G
Models GGAA, GGBA – 50, 60, 70, 80 (500-800 MBh)
Double Furnace
POWER VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
50
60
70
80
A
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
3/4
LP
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
G
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
** “V Dia.” = The Flue Opening; Capacities 60/70/80 will require 5” to 6” increaser on each furnace that will be supplied with the unit.
“J” is an outside dimension for outside or return air dampers.
63
J
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
**V Dia.
5
(127)
**6
(152)
**6
(152)
**6
(152)
Dimensional
Data
High Efficiency Indoor Make-Up Air Handler with High Cfm Blower and Cooling Coil Section – Arrangement K
Models GGAA, GGBA – 50, 60, 70, 80 (500-800 MBh)
Double Furnace
POWER VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
Unit Dimensional Data
Gas Inlet
Capacity
50
60
70
80
A
43 7/8
(1114)
54 7/8
(1394)
54 7/8
(1394)
60 3/8
(1534)
B
29 5/16
(745)
34 13/16
(884)
40 5/16
(1024)
45 13/16
(1164)
NAT
3/4
LP
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
3/4
1/2 OR 3/4
F*
31 1/2
(800)
34 1/4
(870)
42 1/4
(1073)
48
(1219)
G
42 1/16
(1068)
53 1/16
(1348)
53 1/16
(1348)
58 9/16
(1487)
Note:
Dimensions are in inches (Dimensions in parentheses are in millimeters).
*“F” Dimension is the recommended clearance to service the burner drawer.
** “V Dia.” = The Flue Opening; Capacities 60/70/80 will require 5” to 6” increaser on each furnace that will be supplied with the unit.
“J” is an outside dimension for outside or return air dampers.
64
J
35
(889)
46
(1168)
46
(1168)
51 1/2
(1308)
**V Dia.
5
(127)
**6
(152)
**6
(152)
**6
(152)
Dimensional
Data
High Efficiency Indoor Duct Furnace – Arrangement A
Models GGAA, GGBA – 12 (1200 MBh)
Triple Furnace
POWER VENT
(Left Hand Unit Shown)
Note:
*Recommended clearance to service the burner drawer.
**6” Dia. = Flue Opening. The 5” to 6” increaser adapter is supplied by the manufacturer for this model.
Gas inlet sizes: Natural Gas = 3/4” Dia. LP Gas = 1/2” or 3/4” Dia.
High Efficiency Indoor Make-Up Air Handler with High Cfm Blower – Arrangement G
Models GGAA, GGBA – 12 (1200 MBh)
Triple Furnace
POWER VENT
(Left Hand Unit Shown)
Dimensions are in inches.
Dimensions in parentheses are in millimeters.
65
Weights
Table W-1 – Indoor Make-Up Air Handler Unit Weight Data (Pounds)
A
Capacity
Net
Ship
Net
10
NA
NA
537
15
NA
NA
566
20
NA
NA
689
25
NA
NA
716
30
NA
NA
843
35
NA
NA
889
40
NA
NA
950
50
589
686
1035
60
684
788
1219
70
734
838
1289
80
806
914
1386
12
1198
1333
NA
Note:
1. Weights do not include motors or coils.
2. 1 lb. = 0.453 Kg.
B
D
Ship
638
667
798
825
959
1005
1070
1169
1362
1432
1533
NA
Net
715
744
895
922
1083
1129
1206
1241
1459
1529
1642
NA
G
Ship
846
875
1035
1062
1232
1279
1359
1406
1634
1704
1022
NA
Net
NA
NA
848
898
1066
1110
1183
1209
1434
1503
1612
2040
K
Ship
NA
NA
988
1038
1215
1259
1336
1374
1609
1678
1792
2246
Net
775
801
950
1000
1176
1220
1302
1311
1544
1613
1730
NA
Ship
NA
NA
972
1021
1186
1238
1314
1349
1565
1634
1748
2181
Net
774
799
938
984
1146
1199
1280
1286
1500
1569
1687
NA
Ship
930
956
1115
1165
1351
1395
1482
1501
1745
1814
1936
NA
Outside
Air Hood
43
43
51
51
59
59
63
51
59
59
63
63
Ship
929
954
1103
1149
1321
1374
1460
1476
1701
1770
1893
NA
Outside
Air Hood
43
43
51
51
59
59
63
51
59
59
63
63
Table W-2 – High Efficiency Indoor Make-Up Air Handler Unit Weight Data (Pounds)
A
Capacity
Net
Ship
Net
10
NA
NA
536
15
NA
NA
561
20
NA
NA
676
25
NA
NA
703
30
NA
NA
821
35
NA
NA
867
40
NA
NA
928
50
589
686
1010
60
684
788
1175
70
734
838
1246
80
806
914
1343
12
1198
1333
NA
Note:
1. Weights do not include motors or coils.
2. 1 lb. = 0.453 Kg.
B
D
Ship
637
662
785
812
937
983
1048
1144
1318
1389
1490
NA
Net
714
739
882
909
1061
1107
1184
1216
1415
1486
1599
NA
G
Ship
845
870
1022
1049
1210
1256
1337
1381
1590
1661
1779
NA
66
Net
NA
NA
832
881
1037
1089
1161
1184
1390
1459
1568
1975
K
Weights
Table W-3 – Motor Weights
1
Voltage
/2 HP 3/4 HP
1 HP 1 1/2 HP
115/60/1 ODP
20
25
25
40
208/60/1 ODP
21
27
25
40
230/60/1 ODP
21
25
25
40
208/60/3 ODP
20
24
31
29
230/60/3 ODP
20
24
31
29
460/60/3 ODP
20
24
31
29
575/60/3 ODP
20
20
27
31
115/60/1 TE
26
30
34
41
208/60/1 TE
27
36
39
48
230/60/1 TE
26
30
34
41
208/60/3 TE
18
23
28
32
230/60/3 TE
18
23
28
32
460/60/3 TE
18
23
28
32
575/60/3 TE
21
21
26
36
115/60/1 HEODP
32
33
38
58
208/60/1 HEODP
32
30
NA
NA
230/60/1 HEODP
32
33
38
58
208/60/3 HEODP
22
25
40
44
230/60/3 HEODP
24
26
40
43
460/60/3 HEODP
24
26
40
43
575/60/3 HEODP
NA
NA
41
44
115/60/1 HETE
28
37
38
41
208/60/1 HETE
NA
NA
NA
NA
230/60/1 HETE
28
37
38
41
208/60/3 HETE
NA
NA
39
34
230/60/3 HETE
32
52
39
34
460/60/3 HETE
32
52
39
34
575/60/3 HETE
NA
NA
44
69
208/60/3 2S1W
NA
NA
34
38
230/60/3 2S1W
NA
NA
34
38
460/60/3 2S1W
NA
NA
34
38
575/60/3 2S1W
NA
NA
NA
NA
115/60/1 2S2W
23
30
37
NA
208/60/1 2S2W
NA
29
36
NA
230/60/1 2S2W
23
29
36
NA
208/60/3 2S2W
27
32
44
47
230/60/3 2S2W
26
32
44
47
460/60/3 2S2W
26
33
40
44
575/60/3 2S2W
NA
NA
NA
NA
Notes:
1. ODP = Open Drip Proof
2. TE = Totally enclosed
3. HEODP = High Efficiency Open Drip Proof
4. HETE = High Efficiency Totally Enclosed
5. 2S1W = Two Speed One Winding
6. 2S2W = Two Speed Two Winding
7. NA = Not Available
FLA based on NEC Ratings
Table W-4 – Evaporative Cooler Weight
Unit Size
10, 15
20, 25, 50
30, 35, 60, 70
40, 80
Shipping Wt.
lb (Kg)
137
166
192
206
Metric Conversion:
1 lb. = 0.453 Kg.
67
Operating Wt.
lb (Kg)
301
386
468
509
2 HP
42
66
42
35
35
35
37
65
65
65
36
36
36
40
72
NA
72
44
44
44
45
53
NA
53
48
48
48
88
48
48
41
NA
NA
NA
NA
67
67
55
NA
3 HP
80
80
80
47
47
47
56
74
74
74
55
55
55
90
NA
NA
NA
83
80
80
90
NA
NA
NA
71
94
94
76
66
66
58
NA
NA
NA
NA
84
84
67
NA
5 HP
NA
NA
NA
49
49
49
73
NA
NA
NA
65
65
65
92
NA
NA
NA
89
91
91
100
NA
NA
NA
78
110
110
80
81
81
94
NA
NA
NA
NA
NA
NA
NA
NA
7 1/2 HP
NA
NA
NA
99
99
99
105
NA
NA
NA
90
90
90
161
NA
NA
NA
139
137
137
170
NA
NA
NA
107
158
158
132
125
125
125
NA
NA
NA
NA
221
221
214
NA
10 HP
NA
NA
NA
118
118
118
116
NA
NA
NA
123
123
123
199
NA
NA
NA
141
138
138
141
NA
NA
NA
124
166
166
140
143
143
136
NA
NA
NA
NA
192
192
230
NA
15 HP
NA
NA
NA
152
150
150
150
NA
NA
NA
295
295
295
284
NA
NA
NA
213
238
238
215
NA
NA
NA
225
294
294
260
NA
NA
218
NA
NA
NA
NA
NA
NA
NA
NA
Thermostats
Options
Single-Stage Room Thermostat
(Order No. 134-0207-01)
• Low Voltage (24V)
• 40 F to 90 F Range
• Fan Auto-On Switch
Heat-Off-Cool Switch
• System
• 311/16” Diameter; 13/4” Deep
Two-Stage Room Thermostat
(Order No. 134-0207-04)
• Low Voltage (24V)
• 40 F to 90 F Range
• Fan Auto-On Switch
Off-Heat-Auto-Cool Switch
• System
• 55/8” W 31/2” H 21/8” D
Single-Stage Room Thermostat
with Summer/Winter Switch
(Order No. 134-0207-02)
• Low Voltage (24V)
• 55 to 95 F Range
Auto-On Switch
• Fan
• 31/2” W 41/5” H 13/8” D
T7300 Programmable Room
Thermostat
(Order No. 134-0207-05)
• Provides seven-day programmability
for two stages of heating and two
stages of cooling.
• Heat-Off-Cool-Auto system switching
four time periods per day for occupied
and unoccupied modes with threehour override of unoccupied mode.
• Automatic heat-cool changeover and
battery backup.
Universal Guard
(Order No. 134-0207-07)
• Clear Plastic
• Ring Base
• Tumbler7Lock and5 Two Keys
• Cover: 69 /8” W 51 /8” H 33“ D
• Base: 6 /16” W 5 /2” H /8” D
68
Options
Thermostats
Single-Stage Duct Thermostat
(Order No. 134-0207-03)
• Low Voltage (24V)
• 55 to 175 F Range
• 5’ Capillary
• 2” W 55/8” H 27/16” D
Two-Stage Duct Thermostat
(Order No. 134-0207-06)
• Low Voltage (24V)
• 55 to 175 F Range
• 5’ Capillary
• 2” W 55/8” H 27/16” D
Remote Control Station
(Order No. 134-0201-01)
• Wall mounted
• Six LED status lamps
• System on/off, fan auto/on, heat auto/
off, cool auto/off, auxiliary on/off
switching and modulating damper
potentiometer mounting.
• Plug-in terminal block wiring and wall
mounting bracket.
• 61/4” W x 33/4” H x 11/2” D
Seven-Day Timeclock
(Order No. 134-0201-02)
• Single pole double throw (SPDT) relay
output at setpoint time
of six setpoints per day
• Maximum
• 73/4” H x 5” W x 37/16” D
24-Hour Timeclock
(Order No. 134-0201-03)
• Single pole double throw (SPDT) relay
output at setpoint time.
12 setpoints per day.
• Maximum
• 73/4” H x 5” W x 37/16” D
69
Controls
Options
Electronic Modulating Room
Thermostat
(Included with Gas Control)
• Low voltage (24 V)
• 60-85 F range
thermostat
• Room
• 41/2” H x 21/2” W x 11/2” D
Electronic Modulating Duct
Thermostat
(Included with Gas Control)
• Low voltage (24 V)
• 55-90 F range
• Sensor: 10-inch probe
temperature selector:
• Remote
41/4” W x 41/4” H x 17/8” D
thermostat:
• Duct
41/4” W x 41/4” H x 15/8” D
Electronic Modulating Duct
Thermostat with Room
Override
• Line voltage (115 V) roomstat
F range
• 50-90
• 27/8” W x 49/16” H x 11/4” D
• Low voltage (24 V) Ductstat
• 55-90 F range
• Sensor: 10-inch probe
temperature selector:
• Remote
41/4” W x 41/4” H x 15/8” D
thermostat:
• Duct
41/4” W x 41/4” H x 15/8” D
Electronic Modulating
4-20 mA or 0-10 VDC Input
• A200 signal conditioner.
• Control replaces amplifier in duct or
room control package.
70
Discharge Air Control with Outside
Air Reset
• Available in two, three and four-stage
control. Shown above is the discharge
air controller.
Features
Summary
Trane indoor gas heating units have the
following design features:
• All units have AGA and CGA certified
duct furnaces.
• All units are fabricated from aluminized
steel. The heat exchanger uses 20gauge tubes and 18-gauge header
sections.
• Units are complete, wired, tested and
rail-mounted packages with blower
drives preset.
• Units are available with left hand or
right hand gas control configuration.
This flexibility helps to meet special
application requirements.
• Draw-thru cabinet arrangements have
a stainless steel drain pan.
• Evaporative cooling arrangement come
with a standard 8 or optional 12-inch
media (203 or 305 mm).
71
Mechanical
Specifications
Indoor Gas Duct Furnaces
Arrangement A
50-80 (500-800 MBH)
General
Units are completely factory
assembled, piped, wired and test fired.
All units are AGA Certified and conform
with the latest ANSI Standards for safe
and efficient performance. Units are
provided with four point suspension
hangers. All units are available for
operation on either natural or LP
(propane) gas.
Casing
Casings are die-formed, 20-gauge
galvanized steel and finished in baked
enamel. The bottom panel is easily
removed to provide service access to
the burners, pilot and orifices. The pilot
is also accessible through a side panel
access plate. The high limit switch is
accessible through a side panel access.
Duct discharge flanges for simple
ductwork connection are provided.
Heat Exchanger
Standard heat exchanger construction
consists of seam welded 20-gauge
aluminized steel tubes and 18-gauge
aluminized steel headers.
Draft Diverter
Standard draft diverter construction is
corrosion resistant aluminized steel.
Burners
Burners are die-formed, corrosion
resistant aluminized steel, with
stainless steel port protectors. Port
protectors prevent scale or foreign
matter from obstructing the burner
ports. Burners are individually
removable for ease of inspection and
servicing. Each burner is provided with
an individually adjustable, manually
rotated air shutter adjustment. Air
shutter adjustment is fixed.
Controls
A factory installed junction box is
provided for all power connections.
Standard units are provided with a
24-volt combination single-stage
automatic gas valve, including main
operating valve and pilot safety shutoff,
pressure regulator, manual main and
pilot shutoff valve, and adjustable pilot
valve. Gas valve is suitable to a
maximum inlet pressure of 0.5 psi
(14-inch W.C.) on natural gas. A 24-volt
control transformer, a spill (blocked
vent) switch and a high limit are
provided.
All units are provided with a solid-state
ignition control system which ignites
the intermittent pilot by spark during
each cycle of operation. When the pilot
flame is proven, the main burner valve
opens to allow gas flow to the burners.
Pilot and burners are extinguished
during the off cycle.
FACTORY INSTALLED OPTIONS
Control Options (Per Furnace)
Two-Stage Gas Valve
Provides two stages of heat. Ignition is
at low fire (40% of the unit’s full rated
input). Requires the use of an optional
two-stage thermostat.
Hydraulic Modulating Gas Valve
Provides modulated heat output.
Ignition is at low fire (40% of the unit’s
full rated input) and a discharge air
temperature sensing bulb located in
the air stream shall modulate the gas
input from 40% to 100% rated input.
Provided with an automatic electric
valve in series with the hydraulic valve
which cycles the unit in response to an
optional low voltage single-stage
thermostat.
Hydraulic Modulating Gas Valve with
Bypass
Provides modulated heat output.
Ignition is at low fire (40% of the unit’s
full rated input) and a discharge air
temperature sensing bulb located in
the air stream shall modulate the gas
input from 40% to 100% rated input.
Provided with an automatic electric
valve in series with the hydraulic valve
which cycles the unit in response to an
optional low voltage single-stage
thermostat.
An additional electric valve in parallel
bypasses the hydraulic modulating
valve, overriding the discharge
temperature sensing, allowing full fire.
Requires the use of an optional
thermostat to control the electric valve.
Electronic Modulating – Room or Duct
Stat Control
Provides modulated heat output. An
automatic valve in series with the
modulating valve shall be provided to
cycle the unit. Ignition is at full fire
(100% input) and modulates the gas
input from 100% to 40% rated input.
Available for use with a room
thermostat or duct thermostat with
remote set point adjustment. Duct
thermostat available with optional
override room thermostat which
72
causes the unit to go to full fire when
the room temperature falls below the
override room thermostat’s set point.
Electronic Modulating – 4-20 mA or
0-10VDC Input
Provides modulated heat output.
Ignition is at full fire (100% input) and
modulates the gas input from 100% to
40% rated input.
The modulating gas valve shall operate
in response to a 4-20 mA or a 0-10 VDC
input from an external DDC control.
When “furnace one only” is specified
on double and triple furnaces,
additional furnace sections will have
single-stage on-off control.
Discharge Air Control with Outside Air
Reset
The unit is provided with a factorymounted discharge air controller,
discharge air sensor, outdoor air reset,
summer/winter thermostat and velocity
pressure switch. The outdoor air reset
range is from 10 F to 60 F. Full reset
occurs at 10 F outside air temperature.
There is a straight line relationship
between outside air temperature and
reset. Therefore, at 60 F outside air
temperature, no reset will occur. The
amount of reset is adjustable from 20 F
to 50 F.
A discharge air controller provides a
two-minute delay between successive
on and off stages. A summer/winter
thermostat locks out heating when the
outside air temperature is above 55 F.
The velocity pressure switch is provided
for protection against high
temperatures at low airflow’s.
Available in three-stage (33% of the
unit’s full rated input) and four-stage
(25% of the unit’s full rated input).
S-350 Modular Electronic Control
System
The basic system utilizes a controller
module with discharge air sensor,
setpoint and one-stage output, a stage
module with differential setpoint and
one-stage output and a display module
with LCD display for temperature
readout. The system stages the unit’s
rate of fire based upon sensed
discharge air temperature, setpoint
setting and differential setting between
stages.
Provide as a three, four-stage (double
and triple furnaces only) and six-stage
(triple furnace only).
Mechanical
Specifications
Heat Exchanger Options
Type 409 Stainless Steel
Heat exchanger tubes and headers
shall be 20-gauge type 409 stainless
steel. The burners and flue collector
shall be aluminized steel. 409 stainless
steel is recommended when outside air
is used for make-up air in areas where
outside temperatures are 40 F or below
Type 409 Stainless Steel Package
Heat exchanger tubes and headers
shall be 20-gauge type 409 stainless
steel. The burners and flue collector
shall be 409 stainless steel. 409
stainless steel is recommended where
outside air is used for make-up air in
areas where temperatures are 40 F or
below.
Type 321 Stainless Steel
Heat exchanger tubes and headers
shall be 20-gauge type 321 stainless
steel. Burners and flue collector shall
be aluminized steel.
Type 321 Stainless Steel Package
Heat exchanger tubes and headers
shall be 20-gauge type 321 stainless
steel. The burners and flue collector
shall be 409 stainless steel.
Fan Time Delay Relay
The fan time delay relay minimizes cold
blasts of air on start-up. It also allows
the fan to operate after burner
shutdown, removing residual heat
from the heat exchanger.
Orifices for Elevations over 2000 Feet
Freezestat with Time Delay
The unit shall be provided with a
freezestat (0-100 F) with the sensing
bulb located in the discharge air
stream. Wired as an interlock to
prevent cold air discharge.
Firestat
If the temperature reaches the setpoint,
the unit will close all gas valves, return
the dampers to their normal position
and shut down the blower. Automatic
reset.
Supply Air Mounted
(Setpoint typically 150 F)
Manual Blower Switch
409 Stainless Steel Furnace Drip Pan
Clogged Filter Switch
A clogged filter pressure switch with
adjustable operating range and
normally open switch shall be installed
to sense increased suction pressure by
the blower due to filter obstruction. A
provision for remote indication shall be
provided by a terminal block connection
points. Includes a status lamp mounted
in the electrical cabinet.
Continuous Fan Relay – Interlock Relay 24V Coil DPDT 10A
A relay is provided with 24 volt coil and
double-pole, double-throw 10 amp
contacts. It plugs into the main
connection PC board in the electrical
cabinet. May also be used as an
exhaust fan interlock.
Interlock Relay – 24/115V coil SPDT 10A
This relay has a selectable coil voltage
of 24 or 115 volts and single-pole,
double-throw 10 amp contacts with an
LED on the indicator lamp. The relay is
utilized as an auxiliary relay.
Interlock Relay – 24/115-230V Coil DPDT
10A
This relay has a selectable coil voltage
of 24, 115 or 230 volts and double-pole,
double-throw 10 amp contacts. Utilized
as an auxiliary relay for general
purpose duty.
High/Low Gas Pressure Limit Switches
A high pressure and a low pressure
interlock switch and shutoff valve shall
be provided for each furnace section.
High/low gas pressure limits disengage
heating upon detecting either high line
pressure or low manifold pressure.
Status Indicator Lamps (Electrical
Cabinet)
Status indicator lamps shall include
power on, blower on and one lamp per
stage of heat mounted in the electrical
cabinet.
Airflow Proving Switch
Ambient Lockout
FIELD INSTALLED ACCESSORIES
Manual Reset High Limit Switch
The unit shall be provided with a
manual reset, high-limit switch wired in
series to the lead furnace high limit. If
the setpoint is reached, the gas valve
will close and the blower will continue
to run until the sensed temperature is
below the set point.
Flue Vent Fan
The flue vent fan provides power
venting. It is provided with all fixtures
for field mounting and wiring. The flue
vent fan is activated in response to a
single-stage thermostat. A centrifugal
switch in the flue vent fan in turn
activates the automatic electric gas
valve. (One flue vent fan required per
furnace.)
73
High Gas Line Pressure Regulator
Reduces main gas line pressure to a
minimum of 7 inches WC. Pressure at
the jobsite must be specified. The
regulator is selected to accommodate
that specific pressure.
Remote Control Station
Wall mounted. Provides 6 LED status
lamps with System On/Off, Fan Auto/
On, Heat Auto/Off, Cool Auto/Off,
Auxiliary On/Off switching and
modulating damper potentiometer
mounting. Designed for easy
installation with plug-in terminal block
wiring and wall mounting bracket.
7-Day Timeclock
Provides single-pole, double-throw
(SPDT) relay output at setpoint time
with a maximum six setpoints per day.
24-Hour Timeclock
Provides single-pole, double-throw
(SPDT) relay output at setting time with
a maximum 12 setpoints per day.
Disconnect Switch
115V Convenience Outlet
GFI - Ground Fault Convenience Outlet
is manual reset with weatherproof
enclosure - requires separate 115V
power source.
Thermostats
Low-voltage room thermostat, singlestage with fan auto-on-switch and
system heat-off cool switch.
Low-voltage room thermostat, singlestage with a fan auto-on switch.
Low-voltage room thermostat, twostage with a fan auto-on switch and
system off-heat-auto-cool switch.
Low-voltage programmable room
thermostat, two-stage with LCD display,
fan auto-on switch and system-off-heatauto-cool switch.
A universal tamperproof guard for all
room thermostats
Low-voltage duct thermostat, singlestage.
Low-voltage duct thermostat, twostage.
Room thermostat, electronic
modulating control.
Duct thermostat, electronic modulating
control.
Duct thermostat, electronic modulating
control with override room thermostat.
Mechanical
Specifications
Indoor Make-Up Air Handler
Arrangements B, D, G, K
General
Units shall be completely factory
assembled, piped, wired and test fired.
All units shall contain duct furnaces
that are AGA and CGA certified and
conform with the latest ANSI
Standards for safe and efficient
performance. Units are provided with
four-point suspension hangers and
shall be available for operation on
either natural or LP (propane) gas.
The firing rate of each furnace will not
exceed 400 MBh and shall contain its
own heat exchanger, flue collector,
venting, burners, safety and ignition
controls.
All units shall be in compliance with
FM (Factory Mutual) requirements.
Electrical
Standard control relays shall be socket
mounted with terminal block
connections. All control wiring shall
terminate at terminal strips (single
point connection) and include an
identifying marker corresponding to
the wiring diagram.
Motor and control wiring shall be
harnessed with terminal block
connections.
Casing
Casings shall be die-formed, 18-gauge
galvanized steel and finished in air-dry
enamel. Service and access panels
shall be provided through easily
removable side access panels with
captive fasteners. Fan sections and
supply plenums (when provided) shall
be insulated with fire resistant,
odorless, matte-faced one-inch glass
fiber material.
Heat Exchanger
Standard heat exchanger construction
shall consist of 20-gauge aluminized
steel tubes and 18-gauge aluminized
steel headers.
Flue Collector
Standard flue collector construction
shall be corrosion resistant aluminized
steel.
Burners
Burners shall be die-formed, corrosion
resistant aluminized steel, with
stamped porting and stainless steel
port protectors. Port protectors prevent
foreign matter from obstructing the
burner ports. Burners are individually
removable for ease of inspection and
servicing. The entire burner assembly is
easily removed with its slide-out
drawer design. The pilot shall be
accessible through an access plate
without removing the burner drawer
assembly.
Evaporative Cooler
(Standard on arrangement D only)
An evaporative cooler with eight-inch
media shall be provided. The
evaporative cooler shall be of a selfcleaning design with a stainless steel
water tank, regulated water flow and
overflow protection. The cooler shall
have a cabinet assembly of heavygauge aluminized steel with
weatherproof finish, a UL recognized
thermally protected sealed recirculating
pump motor, two-inch distribution pad,
and corrosion-resistant PVC water
distribution tubes.
Cooling Coil Section
(Standard on arrangement K only)
A cooling coil section, constructed of
galvanized steel, shall be provided with
the unit.
Fans
The centrifugal fan shall be belt driven,
forward curved, with a double inlet
statically and dynamically balanced.
The blower wheel shall be fixed on a
keyed shaft, supported with rubber
grommet on bearing only and ball
bearing secured. 7 1/2 through 15 hp
motors do not have the rubber
grommets and are equipped with a
pillow block bearing assembly on the
drive side.
An access interlock switch shall be
installed in the blower compartment
and will disengage the blower upon
removing the service panel. An
override shall be incorporated into the
access interlock switch for
serviceability.
Filters
(Standard on Arrangement B, D Only)
The filter rack shall be constructed of
galvanized steel with access through
the side service panel. Standard filters
are one-inch permanent washable type.
74
Filters
(Standard on Arrangement G, K Only)
The filter rack shall be of v-bank design
for minimal pressure drop and
constructed of galvanized steel with
access through the side service panel.
Standard filters are one-inch
permanent washable type.
Electrical Cabinet
The electrical cabinet shall be isolated
from the air stream with a nonremovable access panel interior to the
outer service panel. There is provision
in this cabinet for component
mounting, wire routing and high
voltage isolation. Motor and control
wiring shall be harnessed with terminal
block connections.
Controls
Standard units shall be provided with a
24-volt combination single-stage
automatic gas valves, including a main
operating valve and pilot safety shutoff,
pressure regulator, manual main and
pilot shutoff valve, and an adjustable
pilot valve. Gas valves shall be suitable
for NEC Class 2 use for a maximum
inlet gas pressure of 0.5 psi (14” WC)
on natural gas. All rooftop units shall
be provided with a low voltage circuit
breaker rated for 150% of the unit’s
normal 24-volt operating load.
Each duct furnace shall be provided
with a 24-volt high temperature limit
switch, a (redundant) combination gas
valve and a fan time delay relay. The
fan time delay relay delays the fan start
until the heat exchanger reaches a
predetermined temperature. It also
allows the fan to operate after burner
shutdown, removing residual heat
from the heat exchanger. Double and
triple furnace units shall contain a
reverse airflow interlock switch. The
normally closed switch, when
activated, shall cause gas valves to
close and continue blower operation.
All units are provided with a solid-state
ignition control system which ignites
the intermittent pilot by spark during
each cycle of operation. When the pilot
flame is proven, the main burner valve
opens to allow gas flow to the burners.
Pilot and burners are extinguished
during the off cycle.
Mechanical
Specifications
FACTORY INSTALLED OPTIONS
Control Options (Per Furnace)
Two-Stage Gas Valve
Provides two stages of heat. Ignition is
at low fire (one half of the unit’s full
rated input). Requires the use of an
optional two-stage thermostat.
Hydraulic Modulating Gas Valve
Provides modulated heat output.
Ignition is at low fire (one half of the
unit’s full rated input), and a discharge
air temperature sensing bulb located in
the air stream shall modulate the gas
input from 40% to 100% rated input.
Provided with an automatic electric
valve in series with the hydraulic valve
which cycles the unit in response to an
optional low voltage single-stage
thermostat.
Hydraulic Modulating Gas Valve
with Bypass
Provides modulated heat output.
Ignition is at low fire (one half of the
unit’s full rated input), and a discharge
temperature sensing bulb located in
the air stream shall modulate the gas
input from 40% to 100% rated input.
Provided with an automatic electric
valve in series with the hydraulic valve
which cycles the unit. An additional
electric valve in parallel bypasses the
hydraulic modulating valve, overriding
the discharge temperature sensing
bulb, allowing full fire. Requires the use
of an optional thermostat to control the
electric valve.
Electronic Modulating – Room or Duct
Stat Control
Provides modulated heat output. An
automatic valve in series with the
modulating valve shall be provided to
cycle the unit. Ignition is at full fire
(100% input), and modulates the gas
input from 100% to 40% rated input.
Available for use with a room
thermostat or duct thermostat with
remote set point adjustment. Duct
thermostat available with optional
override room thermostat which
causes the unit to go to full fire when
the room temperature falls below the
override room thermostat’s set point.
Electronic Modulating - 4-20 mA/
0-10 VDC Input
Provides modulated heat output.
Ignition is at full fire (100% input), and
modulates the gas input from 100% to
40% rated input.
The modulating gas valve shall operate
in response to a 4-20 mA or a 0-10 VDC
input from an external DDC control.
When “furnace one only” is specified
on double and triple furnaces,
additional furnace sections will have
single-stage on-off control.
Discharge Air Control with Outside
Air Reset
The unit is provided with a factorymounted discharge air controller,
discharge air sensor, outdoor air reset,
summer/ winter thermostat and
velocity pressure switch. The outdoor
air reset range is from 10 F to 60 F. Full
reset occurs at 10 F outside air
temperature. There is a straight line
relationship between outside air
temperature and reset. Therefore, at
60 F outside air temperature, no reset
will occur. The amount of reset is
adjustable from 20 F to 50 F.
A discharge air controller provides a
two-minute delay between successive
on and off stages. A summer/winter
thermostat locks out heating when the
outside air temperature is above 55 F.
The velocity pressure switch is
provided for protection against high
temperatures at low airflows.
Available in two-stage (half of the unit’s
full rated input – single furnace units
only), three-stage (33% of the unit’s full
rated input) and four-stage (25% of the
unit’s full rated input). Three and fourstage are available on double and triple
furnace units only.
S-350 Modular Electronic Control
System 2-Stage
The basic system utilizes a controller
module with discharge air sensor,
setpoint and one-stage output, a stage
module with differential setpoint and
one-stage output and a display module
with LCD display for temperature
readout. The system stages the unit’s
rate of fire based upon sensed
discharge air temperature, setpoint
setting and differential setting between
stages.
Provided as a two-stage (all furnaces),
three and four-stage (double and triple
furnaces only) and six-stage (triple
furnace only).
75
Heat Exchanger Options
Type 409 Stainless Steel
(one or all furnaces)
Heat exchanger tubes and headers
shall be 20-gauge type 409 stainless
steel. The burners and flue collector
shall be aluminized steel. 409 stainless
steel is recommended when outside
air is used for make-up air in areas
where outside temperatures are 40 F
or below.
Type 409 Stainless Steel Package
(one or all furnaces)
Heat exchanger tubes and headers
shall be 20-gauge type 409 stainless
steel. The burners and flue collector
shall be 409 stainless steel. 409
stainless steel is recommended where
outside air is used for make-up air in
areas where outside temperatures are
40 F or below.
Type 321 Stainless Steel
(one or all furnaces)
Heat exchanger tubes and headers
shall be 20-gauge type 321 stainless
steel. Burners and flue collector shall
be aluminized steel.
Type 321 Stainless Steel Package
(one or all furnaces)
Heat exchanger tubes and headers
shall be 20-gauge type 321 stainless
steel. The burners and flue collector
shall be 409 stainless steel.
Motors - General
All motors shall be ball bearing type
with resilient base mount. Windings
are Class “B”, 1800 rpm with service
factors of 1/2 - 3/4 hp = 1.25 and
1 - 5 hp = 1.15.
Single-Speed Open Drip-proof
60 HZ/1800 RPM
Single-Phase (with contactor) Optional 115V, 208V and 230V motors
available in 1/2 - 2 hp models.
Three-Phase (with contactor) - Optional
208V, 230V and 460V motors available
in 1/2 - 5 hp models.
Single-Phase (with magnetic starter) Optional 115V, 208V and 230V motors
available in 1/2 - 3 hp models.
Three-Phase (with magnetic starter) Optional 208V, 230V, 460V and 575V
motors available in 1/2-5 hp models.
Mechanical
Specifications
Single Speed TEFC 60 HZ/1800 RPM
Single-Phase (with contactor) Optional 208V, 230V and 230V motors
available in 1/2 - 1 1/2 hp models.
Manual Blower Switch
A manual blower switch shall be
factory installed in the electrical
cabinet.
Single-Phase (with magnetic starter) Optional 115V, 208V and 230V motors
available in 1/2 - 3 hp models.
DX or Chilled Water Cooling Coils
A direct expansion (DX) or chilled water
coil certified by ARI shall be provided
with the unit (available on Arrangement
K only).
Three-Phase (with magnetic starter) Optional 208V, 230V, 460V and 575V
motors available in 1/2 - 5 hp models.
Single-Speed High Efficiency ODP
60 HZ/1800 RPM
Single-Phase (with contactor) Optional 115V and 230V motors
available in 1/2 - 1 hp models. Optional
208V motors available in 1/2 - 3/4 hp
models.
Single-Phase (with magnetic starter) Optional 115V and 230V motors
available in 1/2 - 2 hp models. Optional
208V motors available in 1/2 - 3/4 hp
models.
Three-Phase (with magnetic starter) Optional 208V, 230V and 460V motors
available in 1/2 - 5 hp models. Optional
575V motors available in 1 - 5 hp
models.
Single-Speed High Efficiency TEFC
60 HZ/1800 RPM
Single-Phase (with contactor) Optional 115V and 230V motors
available in 1/2 - 1 1/2 hp models.
Single-Phase (with magnetic starter) Optional 115V and 230V motors
available in 1/2 - 2 hp models.
Three-Phase (with magnetic starter) Optional 230V and 460V motors
available in 1/2 - 5 hp models. Optional
208V and 575V available in 1 - 5 hp
models.
Two-Speed/One Winding Motors
(Three Phase On;y)
60 HZ/1800/900 RPM
Three-Phase (with magnetic starter) Optional 208V, 230V and 460V motors
available in 1 - 5 hp models.
Two-Speed/Two Winding Motors
60 HZ/1800/1200 RPM
Single-Phase (with magnetic starter) Optional 115V and 230V motors
available in 1/2 - 1 hp models. Optional
208V motors available in 3/4 - 1 hp
models.
Three-Phase (with magnetic starter) Optional 208V and 230V motors
available in 1/2 - 5 hp models. Optional
460V motors available in 1/2 - 3 hp
models.
Damper Options
Dampers shall be of the opposed blade
type, constructed of galvanized steel
with neoprene nylon bushings, blades
to be mechanically interlocked.
Optional low leak dampers shall be of
the opposed blade type, construction of
galvanized steel with neoprene nylon
bushings and vinyl blade edge seals,
blades to be mechanically interlocked.
Outside Air or Return Air/
2 pos. Motor/SR
Units with outside air or return air only
shall be provided with a damper, twoposition spring return damper motor
and controls. The motor shall power the
damper fully open when the unit is on
and fully closed when the unit is off.
OA/RA 2 Pos SR
A two-position spring return motor
with interlocked outside and return air
dampers shall be provided. The motor
shall power either the outside air
damper fully open and the return air
damper fully closed or the outside air
damper fully closed and the return air
damper fully open in response to an
outside air temperature sensor. When
the unit is off, the motor will drive the
outside air damper fully closed and the
return air damper fully open.
OA/RA Mod Motor with Mixed Air
Control/Min. Pot/Spring Return
Modulating motor with interlocked
outside and return air dampers shall be
provided. The motor shall modulate the
position of the outside and return air
dampers in response to a thermostatic
controller located in the mixed air
stream. Units shall also be provided
with a minimum position
potentiometer for minimum outside air
damper position.
The spring return feature drives the
outside air damper fully closed and the
return air damper fully open when the
unit is off.
76
OA/RA Mod Mtr. with Mixed
Air Control/Spring Return
A modulating motor with interlocked
outside and return air dampers shall
be provided. The motor shall modulate
the position of the outside and return
air dampers in response to a
thermostatic controller located in the
mixed air stream.
The spring return feature drives the
outside air damper fully closed and the
return air damper fully open when the
unit is off.
OA/RA Mod Mtr with Min Pot/
Spring Return
A modulating motor with interlocked
outside and return air dampers shall
be provided. The motor shall position
the outside and return air dampers in
response to a manually set
potentiometer.
The spring return feature drives the
outside air damper fully closed and the
return air damper fully open when the
unit is off.
OA/RA Mod Mtr with Dry Bulb/Mixed
Air Control/Min Pot/Spring Return
A modulating motor with interlocked
outside and return air dampers shall
be provided. The motor shall modulate
the position of the outside and return
air dampers in response to a
thermostatic controller and dry bulb
thermostat located in the mixed air
stream. Units shall also be provided
with a minimum position
potentiometer for minimum outside air
damper position.
The spring return feature drives the
outside air damper fully open and the
return air damper fully closed when
the unit is off.
OA/RA Mod Mtr with Enthalpy
Controlled Economizer/SR
A modulating motor with spring return
and interlocked outside and return air
dampers shall be provided. The motor
shall modulate the position of the
outside and return air dampers in
response to an enthalpy controlled
economizer. When the unit is off, the
motor will drive the outside air damper
fully closed and the return air damper
fully open.
Mechanical
Specifications
OA/RA Mod Mtr with Space
Pressure Controller
A modulating motor with spring return
and interlocked outside and return air
dampers shall be provided. The motor
shall modulate the position of the
outside and return air dampers in
response to a pressure sensor located
in the building. When the unit is off, the
motor will drive the outside air damper
fully closed and the return air damper
fully open.
OA/RA Mod Mtr with S-350P
Proportional Mixed Air Control/SR
A modulating motor with spring return
and interlocked outside and return air
dampers shall be provided. The motor
shall modulate the position of the
outside and return air dampers in
response to a solid-state mixed air
sensor and S-350 Proportional
controller. When the unit is off, the
motor will drive the outside air damper
fully closed and the return air damper
fully open.
OA/RA Mtr. with External 4-20 mA or 010VDC Analog Input/Spring Return
A modulating motor interlocked with
outside and return air dampers shall be
provided. The motor shall modulate the
position of the outside and return air
dampers in response to a 4-10 mA or 010VDC signal supplied by an external
DDC controller.
The spring return feature drives the
outside air damper fully closed and the
return air damper fully open when the
unit is shut down.
ASHRAE Cycle I
(OA/RA 2 pos with warm-up stat/SR)
A two-position spring return motor
with interlocked outside and return air
dampers shall be provided. The motor
shall power the outside air damper fully
open after a warm up period
determined by a minimum supply air
temperature sensor when the unit is
on, and fully closed when the unit is off.
ASHRAE Cycle II (OA/RA Mod with
Warm-up Stat/Mixed Air/Min Pot/
Spring Return)
A modulating motor with interlocked
outside and return air dampers shall be
provided. The motor shall modulate the
position of the outside and return air
dampers in response to a thermostatic
controller located in the mixed air
stream after a warm-up period
determined by a minimum supply air
temperature sensor.
Units shall also be provided with a
minimum position potentiometer for
minimum outside air damper position.
When the unit is off, the motor will
drive the outside air damper full closed
and the return air damper full open.
ASHRAE Cycle III (OA/RA Mod. with
Warm-up Stat/Mixed Air/SR)
A modulating motor with spring return
and interlocked outside and return air
dampers shall be provided. The motor
shall modulate the position of the
outside and return air dampers in
response to a thermostatic controller
located in the mixed air stream after a
warm-up period determined by a
minimum supply air temperature
sensor. Units shall also be provided
with a minimum position
potentiometer for minimum outside air
damper position. When the unit is off,
the motor will drive the outside air
damper fully closed and the return air
damper fully open.
Manual Dampers
Units with outside air and return air
shall be provided with manually set
outside and return air dampers.
Firestat
If the temperature reaches the setpoint,
the unit will close all gas valves, return
the dampers to their normal position
and shut down the blower. Automatic
reset.
Return Air Mounted
(setpoint typically 130 F)
Standard on Arrangements B and D.
Utilized on these arrangements as a
reverse airflow switch.
Supply Air Mounted
(setpoint typically 150 F)
Freezestat
The unit shall be provided with a
freezestat (0-100 F) with the sensing
bulb located in the discharge air
stream. Wired as an interlock to prevent
cold air discharge.
Orifices for Elevations over 2000 feet
12” Evaporative Media
(Arrangement D only)
12” media shall be provided for the
evaporative cooler.
409 Stainless Steel Furnace Drip Pan
Replaces the standard aluminized steel
furnace drain pan.
77
Double Wall Construction
The construction will consist of a 24gauge inner liner wall with 1-inch 1½
lb. density insulation. Access doors on
the specified side will be hinged and of
the same double wall design. Double
wall is not available on the applicable
evaporative cooler and furnace
sections. Double wall construction will
be provided by the manufacturer on
applicable filter/damper, blower, coil
and plenum cabinets.
Clogged Filter Switch
A clogged filter pressure switch with
adjustable operating range and
normally open switch shall be installed
to sense increased suction pressure by
the blower due to filter obstruction.
A provision for remote indication shall
be provided by a terminal block
connection points. Includes a status
lamp mounted in the electrical cabinet.
Horizontal Return
The unit shall be supplied with the
return air opening at or under the
outside air opening location depending
on the air inlet configuration.
Continuous Fan Relay – 24V Coil
DPDT 10A
A relay is provided with 24 volt coil and
double-pole, double-throw 10 amp
contacts. It plugs into the main
connection PC board in the electrical
cabinet. Included as standard on
Arrangements D and E. May also be
utilized as an exhaust fan interlock.
Interlock Relay – 24/115V Coil
SPDT 10A
This relay has a selectable coil voltage
of 24 or 115 volts and single-pole,
double-throw 10 amp contacts with an
LED on the indicator lamp. The relay is
utilized as an auxiliary relay.
Interlock Relay – 24/115-230V Coil
DPDT 10A
This relay has a selectable coil voltage
of 24, 115 or 230 volts and double-pole,
double-throw 10 amp contacts. Utilized
as an auxiliary relay for general
purpose duty.
High/Low Gas Pressure
Limit Switches
A high pressure and a low pressure
interlock switch and shutoff valve shall
be provided for each furnace section.
High/low gas pressure limits disengage
heating upon detecting either high line
pressure or low manifold pressure.
Mechanical
Specifications
Status Indicator Lamps
(Elec Cabinet)
Status indicator lamps shall include
power on, blower on and one lamp per
stage of heat mounted in the electrical
cabinet.
Ambient Lockout
Airflow Proving Switch
Hinged Service Access Doors
Optional hinged doors are mounted to
the access side of the standard blower/
filter/damper cabinet and high CFM
filter/damper and blower cabinets in
leau of the standard removable access
doors. The hinged doors include dual
quick opening tool-less latches and full
perimeter gasketing to assure a water
tight seal and door stops to guard
against closure while open. The
remaining Duct Furnace(s), supply
plenum cabinets (if applicable) are
supplied with a standard removable
door. The coil cabinet door utilizes a
special removable vertical split door
allowing for coil access and unit
penetration for coil connections.
FIELD INSTALLED ACCESSORIES
Disconnect Switch
Manual Reset High Limit Switch
The unit shall be provided with a
manual reset, high-limit switch wired in
series to the lead furnace high limit. If
the setpoint is reached, the gas valve
will close and the blower will continue
to run until the sensed temperature is
below the set point.
115V Convenience Outlet
GFI (Ground Fault Convenience Outlet)
is manual reset with a weatherproof
enclosure.
Flue Vent Fan
The flue vent fan provides power
venting. It is provided with all fixtures
for field mounting and wiring. The flue
vent fan is activated in response to a
single-stage thermostat. A centrifugal
switch in the flue vent fan in turn
activates the automatic electric gas
valve. (One flue vent fan required per
furnace.)
High Gas Line Pressure Regulator
Reduces main gas line pressure to a
minimum of 7 inches WC. Pressure at
the jobsite must be specified. The
regulator is selected to accommodate
that specific pressure.
Remote Control Station
Wall mounted. Provides six LED status
lamps with System On/Off, Fan Auto/
On, Heat Auto/Off, Cool Auto/Off,
Auxiliary On/Off switching and
Modulating damper potentiometer
mounting. Designed for easy
installation with plug-in terminal block
wiring and wall mounting bracket.
(Auxiliary On/Off may be used with the
Evaporative Cooler fill and drain kit.)
7-Day Timeclock
Provides single-pole, double-throw
(SPDT) relay output at setpoint time
with a maximum six setpoints per day.
24-Hour Timeclock
Provides single-pole, double-throw
(SPDT) relay output at setting time with
a maximum 12 setpoints per day.
Fill and Drain Kit
(Arrangement D only)
Includes a three-way valve and relay
for automatic fill and drain for the
evaporative coolers. Optional
freezestat provides automatic shutoff
and drain upon meeting outside air
setpoint.
Optional Filters
(One-inch permanent standard)
Two-inch Permanent
Two-inch Throwaway
One-inch 30% Pleated Media
Two-inch 30% Pleated Media
Thermostats
Low-voltage room thermostat, singlestage with fan auto-on-switch and
system heat-off cool switch.
Low-voltage room thermostat, singlestage with a fan auto-on switch.
Low-voltage room thermostat, twostage with a fan auto-on switch and
system off-heat-auto-cool switch.
Low-voltage programmable room
thermostat, two-stage with LCD
display, fan auto-on switch and system
off-heat-auto-cool switch.
A universal tamperproof guard for all
room thermostats.
Low-voltage duct thermostat, singlestage.
Low-voltage duct stat, two-stage.
Room thermostat, electronic
modulating control.
Duct thermostat, electronic modulating
control.
Duct thermostat, electronic modulating
control with override room thermostat.
78
Mechanical
Specifications
High Efficiency Indoor Gas
Duct Furnaces
Arrangement A
50-80 (500-800 MBh)
General
Units are completely factory
assembled, piped, wired and test fired.
All units are AGA Certified and
conform with the latest ANSI
Standards for safe and efficient
performance. Units are provided with
four point suspension hangers. All
units are available for operation on
either natural or LP (propane) gas.
Casing
Casings are die-formed, 20-gauge
galvanized steel and finished in baked
enamel. The bottom panel is easily
removed to provide service access to
the burners, pilot and orifices. The pilot
is also accessible through a side panel
access plate. The high limit switch is
accessible through a side panel access.
Duct discharge flanges for simple
ductwork connection are provided.
Heat Exchanger
Standard heat exchanger construction
consists of seam welded 20-gauge
aluminized steel tubes and 18-gauge
aluminized steel headers.
Controls
A factory installed junction box is
provided for all power connections.
Standard units are provided with a 24volt combination single-stage
automatic gas valve, including main
operating valve and pilot safety shutoff,
pressure regulator, manual main and
pilot shutoff valve, and adjustable pilot
valve. Gas valve is suitable to a
maximum inlet pressure of 0.5 psi (14inch W.C.) on natural gas. A 24-volt
control transformer and a high limit are
provided.
All units are provided with a solid-state
ignition control system which ignites
the intermittent pilot by spark during
each cycle of operation. When the pilot
flame is proven, the main burner valve
opens to allow gas flow to the burners.
Pilot and burners are extinguished
during the off cycle.
Flue Vent Fan
The flue vent fan is factory assembled
to a sealed flue collection chamber and
provides power venting. The flue vent
fan is activated in response to a low
voltage (24V) single stage thermostat.
A combustion air pressure switch is
provided as standard to verify proper
powered vent flow prior to allowing the
gas valve to operate.
Burners
Burners are die-formed, corrosion
resistant aluminized steel, with
stainless steel port protectors. Port
protectors prevent scale or foreign
matter from obstructing the burner
ports. Burners are individually
removable for ease of inspection and
servicing. Each burner is provided with
an individually adjustable, manually
rotated air shutter adjustment. Air
shutter adjustment is fixed.
FACTORY INSTALLED OPTIONS
Control Options (Per Furnace)
Two-Stage Gas Valve
Provides two stages of heat. Ignition is
at low fire (40% of the unit’s full rated
input). Requires the use of an optional
two-stage thermostat.
Hydraulic Modulating Gas Valve
Provides modulated heat output.
Ignition is at low fire (40% of the unit’s
full rated input) and a discharge air
temperature sensing bulb located in the
air stream shall modulate the gas input
from 40% to 100% rated input.
Provided with an automatic electric
valve in series with the hydraulic valve
which cycles the unit in response to an
optional low voltage single-stage
thermostat.
Hydraulic Modulating Gas Valve with
Bypass
Provides modulated heat output.
Ignition is at low fire (40% of the unit’s
full rated input) and a discharge air
temperature sensing bulb located in the
air stream shall modulate the gas input
from 40% to 100% rated input.
Provided with an automatic electric
valve in series with the hydraulic valve
which cycles the unit in response to an
optional low voltage single-stage
thermostat.
An additional electric valve in parallel
bypasses the hydraulic modulating
valve, overriding the discharge
temperature sensing, allowing full fire.
Requires the use of an optional
thermostat to control the electric valve.
Electronic Modulating - Room or Duct
Stat Control
Provides modulated heat output. An
automatic valve in series with the
modulating valve shall be provided to
cycle the unit. Ignition is at full fire
(100% input) and modulates the gas
input from 100% to 40% rated input.
Available for use with a room
thermostat or duct thermostat with
remote set point adjustment. Duct
thermostat available with optional
override room thermostat which causes
the unit to go to full fire when the room
temperature falls below the override
room thermostat’s set point.
79
Mechanical
Specifications
Electric Modulating - 4-20 mA or
0-10 VDC Input
Provides modulated heat output.
Ignition is at full fire (100% input) and
modulates the gas input from 100% to
40% rated input.
The modulating gas valve shall operate
in response to a 4-20 mA or a 0-10 VDC
input from an external DDC control.
When “furnace one only” is specified
on double and triple furnaces,
additional furnace sections will have
single-stage on-off control.
Discharge Air Control with Outside Air
Reset
The unit is provided with a factorymounted discharge air controller,
discharge air sensor, outdoor air reset,
summer/winter thermostat and
velocity pressure switch. The outdoor
air reset range is from 10 F to 60 F. Full
reset occurs at 10 F outside air
temperature. There is a straight line
relationship between outside air
temperature and reset. Therefore, at 60
F outside air temperature, no reset will
occur. The amount of reset is
adjustable from 20 F to 50 F.
A discharge air controller provides a
two-minute delay between successive
on and off stages. A summer/winter
thermostat locks out heating when the
outside air temperature is above 55 F.
The velocity pressure switch is
provided for protection against high
temperatures at low airflow’s.
Available in three-stage (33% of the
unit’s full rated input) and four-stage
(25% of the unit’s full rated input).
S-350 Modular Electronic Control
System
The basic system utilizes a controller
module with discharge air sensor,
setpoint and one-stage output, a stage
module with differential setpoint and
one-stage output and a display module
with LCD display for temperature
readout. The system stages the unit’s
rate of fire based upon sensed
discharge air temperature, setpoint
setting and differential setting between
stages.
Heat Exchanger Options
Manual Blower Switch
Type 409 Stainless Steel
Heat exchanger tubes and headers
shall be 20-gauge type 409 stainless
steel. The burners and flue collector
shall be aluminized steel. 409 stainless
steel is recommended when outside
air is used for make-up air in areas
where outside temperatures are 40 F
or below
409 Stainless Steel Furnace Drip Pan
Type 409 Stainless Steel Package
Heat exchanger tubes and headers
shall be 20-gauge type 409 stainless
steel. The burners and flue collector
shall be 409 stainless steel. 409
stainless steel is recommended where
outside air is used for make-up air in
areas where temperatures are 40 F
or below.
Type 321 Stainless Steel
Heat exchanger tubes and headers
shall be 20-gauge type 321 stainless
steel. Burners and flue collector shall
be aluminized steel.
Type 321 Stainless Steel Package
Heat exchanger tubes and headers
shall be 20-gauge type 321 stainless
steel. The burners and flue collector
shall be 409 stainless steel.
Fan Time Delay Relay
The fan time delay relay minimizes
cold blasts of air on start-up. It also
allows the fan to operate after burner
shutdown, removing residual heat
from the heat exchanger.
Orifices for Elevations over 2000 Feet
Freezestat with Time Delay
The unit shall be provided with a
freezestat (0-100 F) with the sensing
bulb located in the discharge air
stream. Wired as an interlock to
prevent cold air discharge.
Firestat
If the temperature reaches the setpoint,
the unit will close all gas valves, return
the dampers to their normal position
and shut down the blower. Automatic
reset.
Supply Air Mounted
(setpoint typically 150 F)
Provide as a three and four-stage
(double and triple furnaces only) and
six-stage (triple furnace only).
80
Clogged Filter Switch
A clogged filter pressure switch with
adjustable operating range and
normally open switch shall be installed
to sense increased suction pressure by
the blower due to filter obstruction.
A provision for remote indication shall
be provided by a terminal block
connection points. Includes a status
lamp mounted in the electrical cabinet.
Continuous Fan Relay (Interlock Relay 24V Coil DPDT 10A
A relay is provided with 24 volt coil and
double-pole, double-throw 10 amp
contacts. It plugs into the main
connection PC board in the electrical
cabinet. May also be used as an
exhaust fan interlock.
Interlock Relay - 24/115V coil
SPDT 10A
This relay has a selectable coil voltage
of 24 or 115 volts and single-pole,
double-throw 10 amp contacts with an
LED on the indicator lamp. The relay is
utilized as an auxiliary relay.
Interlock Relay - 24/115-230V Coil
DPDT 10A
This relay has a selectable coil voltage
of 24, 115 or 230 volts and double-pole,
double-throw 10 amp contacts.
Utilized as an auxiliary relay for general
purpose duty.
High/Low Gas Pressure Limit Switches
A high pressure and a low pressure
interlock switch and shutoff valve shall
be provided for each furnace section.
High/low gas pressure limits disengage
heating upon detecting either high line
pressure or low manifold pressure.
Status Indicator Lamps (Electrical
Cabinet)
Status indicator lamps shall include
power on, blower on and one lamp per
stage of heat mounted in the electrical
cabinet.
Airflow Proving Switch
Ambient Lockout
Mechanical
Specifications
FIELD INSTALLED ACCESSORIES
Manual Reset High Limit Switch
The unit shall be provided with a
manual reset, high-limit switch wired in
series to the lead furnace high limit. If
the setpoint is reached, the gas valve
will close and the blower will continue
to run until the sensed temperature is
below the set point.
High Gas Line Pressure Regulator
Reduces main gas line pressure to a
minimum of 7 inches WC. Pressure at
the jobsite must be specified. The
regulator is selected to accommodate
that specific pressure.
Remote Control Station
Wall mounted. Provides six LED status
lamps with System On/Off, Fan Auto/
On, Heat Auto/Off, Cool Auto/Off,
Auxiliary On/Off switching and
modulating damper potentiometer
mounting. Designed for easy
installation with plug-in terminal block
wiring and wall mounting bracket.
7-Day Timeclock
Provides single-pole, double-throw
(SPDT) relay output at setpoint time
with a maximum six setpoints per day.
24-Hour Timeclock
Provides single-pole, double-throw
(SPDT) relay output at setting time with
a maximum 12 setpoints per day.
Disconnect Switch
115V Convenience Outlet
GFI - Ground Fault Convenience Outlet
is manual reset with weatherproof
enclosure - requires separate 115V
power source.
81
Thermostats
Low-voltage room thermostat, singlestage with fan auto-on-switch and
system heat-off cool switch.
Low-voltage room thermostat, singlestage with a fan auto-on switch.
Low-voltage room thermostat, twostage with a fan auto-on switch and
system off-heat-auto-cool switch.
Low-voltage programmable room
thermostat, two-stage with LCD
display, fan auto-on switch and systemoff-heat-auto-cool switch.
A universal tamperproof guard for all
room thermostats
Low-voltage duct thermostat, singlestage.
Low-voltage duct thermostat, twostage.
Room thermostat, electronic
modulating control.
Duct thermostat, electronic modulating
control.
Duct thermostat, electronic modulating
control with override room thermostat.
Mechanical
Specifications
High Efficiency Indoor
Make-Up Air Handler
Arrangement B, D, G, K
General
Units shall be completely factory
assembled, piped, wired and test fired.
All units shall contain duct furnaces
that are AGA and CGA certified and
conform with the latest ANSI
Standards for safe and efficient
performance. Units are provided with
four-point suspension hangers and
shall be available for operation on
either natural or LP (propane) gas.
The firing rate of each furnace will not
exceed 400 MBh and shall contain its
own heat exchanger, flue collector,
venting, burners, safety and ignition
controls.
All units shall be in compliance with
FM (Factory Mutual) requirements.
Electrical
Standard control relays shall be socket
mounted with terminal block
connections. All control wiring shall
terminate at terminal strips (singlepoint connection) and include an
identifying marker corresponding to
the wiring diagram
Motor and control wiring shall be
harnessed with terminal block
connections.
Casing
Casings shall be die-formed, 18-gauge
galvanized steel and finished in air-dry
enamel. Service and access panels
shall be provided through easily
removable side access panels with
captive fasteners. Fan sections and
supply plenums (when provided) shall
be insulated with fire-resistant,
odorless, matte-faced, one-inch glass
fiber material.
Heat Exchanger
Standard heat exchanger construction
shall consist of 20-gauge aluminized
steel tubes and 18-gauge aluminized
steel headers.
Burners
Burners shall be die-formed, corrosion
resistant aluminized steel, with
stamped porting and stainless steel
port protectors. Port protectors prevent
foreign matter from obstructing the
burner ports. Burners are individually
removable for ease of inspection and
servicing. The entire burner assembly is
easily removed with its slide-out
drawer design. The pilot shall be
accessible through an access plate
without removing the burner drawer
assembly.
Evaporative Cooler
(Standard on Arrangement D only)
An evaporative cooler with eight-inch
media shall be provided. The
evaporative cooler shall be of a selfcleaning design with a stainless steel
water tank, regulated water flow and
overflow protection. The cooler shall
have a cabinet assembly of heavygauge aluminized steel with
weatherproof finish, a UL recognized
thermally protected, sealed
recirculating pump motor, two-inch
distribution pad, and corrosion
resistant PVC water distribution tubes.
Coil Section
(Standard on Arrangement K only)
A cooling coil section, constructed of
galvanized steel, shall be provided with
the unit.
Fans
The centrifugal fan shall be belt driven,
forward curved, with double inlet
statically and dynamically balanced.
The blower wheel shall be fixed on a
keyed shaft, supported with rubber
grommet on bearing only and ball
bearing secured. 7 1/2 through 15 hp
motors do not have the rubber
grommets and are equipped with a
pillow block bearing assembly on the
drive side.
An access interlock switch shall be
installed in the blower compartment
and will disengage the blower upon
removing the service panel. An
override shall be incorporated into
the access interlock switch for
serviceability.
Filters
(Standard on Arrangement B,D only)
The filter rack shall be constructed of
galvanized steel with access through
the side service panel. Standard filters
are one-inch permanent washable
type.
Filters
(Standard on Arrangement G, K only)
The filter rack shall be of v-bank design
for minimal pressure drop and
constructed of galvanized steel with
access through the side service panel.
Standard filters are one-inch
permanent washable type.
82
Electrical Cabinet
The electrical cabinet shall be isolated
from the air stream with a nonremovable access panel interior to the
outer service panel. There is a provision
in this cabinet for component
mounting, wire routing and highvoltage isolation.
Motor and control wiring shall be
harnessed with terminal block
connections.
Controls
Standard units shall be provided with
24 volt combination single-stage
automatic gas valves, including main
operating valve and pilot safety shutoff,
pressure regulator, manual main and
pilot shutoff valve, and adjustable pilot
valve. Gas valves shall be suitable for
NEC Class 2 use for a maximum inlet
gas pressure of 0.5 psi (14” WC) on
natural gas. All rooftop units shall be
provided with a low voltage circuit
breaker rated for 150% of the units
normal 24 volt operating load.
Each duct furnace shall be provided
with a 24 volt high temperature limit
switch, a (redundant) combination gas
valve and a fan time delay relay. The fan
time delay relay delays the fan start
until the heat exchanger reaches a
predetermined temperature. It also
allows the fan to operate after burner
shutdown, removing residual heat from
the heat exchanger. Double and triple
furnace units shall contain a reverse
airflow interlock switch. The normally
closed switch, when activated, shall
cause gas valves to close and continue
blower operation.
All units are provided with a solid-state
ignition control system which ignites
the intermittent pilot by spark during
each cycle of operation. When the pilot
flame is proven, the main burner valve
opens to allow gas flow to the burners.
The pilot and burners are extinguished
during the off cycle.
Flue Vent Fan
The flue vent fan is factory assembled
to a sealed flue collection chamber and
provides power venting. The flue vent
fan is activated in response to a low
voltage (24 volt) single stage
thermostat. A combustion air pressure
switch is provided as standard to verify
proper powered vent flow prior to
allowing the gas valve to operate.
Mechanical
Specifications
FACTORY INSTALLED OPTIONS
Control Options (Per Furnace)
Two-Stage Gas Valve
Provides two stages of heat. Ignition is
at low fire (one half of the unit’s full
rated input). Requires the use of an
optional two-stage thermostat.
Hydraulic Modulating Gas Valve
Provides modulated heat output.
Ignition is at low fire (one half of the
unit’s full rated input), and a discharge
air temperature sensing bulb located in
the air stream shall modulate the gas
input from 40% to 100% rated input.
Provided with an automatic electric
valve in series with the hydraulic valve
which cycles the unit in response to an
optional low voltage single-stage
thermostat.
Hydraulic Modulating Gas
Valve with Bypass
Provides modulated heat output.
Ignition is at low fire (one half of the
unit’s full rated input), and a discharge
temperature sensing bulb located in the
air stream shall modulate the gas input
from 40% to 100% rated input. Provided
with an automatic electric valve in
series with the hydraulic valve which
cycles the unit. An additional electric
valve in parallel bypasses the hydraulic
modulating valve, overriding the
discharge temperature sensing bulb,
allowing full fire. Requires the use of an
optional thermostat to control the
electric valve.
Electronic Modulating - Room or Duct
Stat Control
Provides modulated heat output. An
automatic valve in series with the
modulating valve shall be provided to
cycle the unit. Ignition is at full fire
(100% input), and modulates the gas
input from 100% to 40% rated input.
Available for use with a room
thermostat or duct thermostat with
remote setpoint adjustment. A duct
thermostat is available with an optional
override room thermostat which causes
the unit to go to full fire when the room
temperature falls below the override
room thermostat’s setpoint.
Electronic Modulating - 4-20 mA/
0-10 VDC input
Provides modulated heat output.
Ignition is at full fire (100% input) and
modulates the gas input from 100% to
40% rated input.
The modulating gas valve shall operate
in response to a 4-20 mA or a 0-10 VDC
input from an external DDC control.
When “furnace one only” is specified
on double and triple furnaces,
additional furnace sections will have
single-stage on-off control.
Discharge Air Control with Outside
Air Reset
The unit is provided with a factorymounted discharge air controller,
discharge air sensor, outdoor air reset,
summer/winter thermostat and
velocity pressure switch. The outdoor
air reset range is from 10 F to 60 F. Full
reset occurs at 10 F outside air
temperature. There is a straight line
relationship between outside air
temperature and reset. Therefore, at
60 F outside air temperature, no reset
will occur. The amount of reset is
adjustable from 20 F to 50 F.
The discharge air controller provides a
two-minute delay between successive
on and off stages. A summer/winter
thermostat locks out heating when the
outside air temperature is above 55 F.
The velocity pressure switch is
provided for protection against high
temperatures at low airflows.
Available in two-stage (half of the unit’s
full rated input – single furnace units
only), three-stage (33% of the unit’s full
rated input) and four-stage (25% of the
unit’s full rated input). Three and fourstage available on double and triple
furnace units only.
S-350 Modular Electronic Control
System
The basic system utilizes a controller
module with a discharge air sensor,
setpoint and one-stage output, a stage
module with differential setpoint and
one-stage output and a display module
with LCD display for temperature
readout. The system stages the unit’s
rate of fire based upon sensed
discharge air temperature, setpoint
setting and differential setting between
stages.
Provided as a two-stage (all furnaces),
three and four-stage (double and triple
furnaces only) and six-stage (triple
furnace only).
83
Heat Exchanger Options
Type 409 Stainless Steel
(one or all furnaces)
Heat exchanger tubes and headers
shall be 20-gauge type 409 stainless
steel. The burners and flue collector
shall be aluminized steel. 409 stainless
steel is recommended when outside
air is used for make-up air in areas
where outside temperatures are 40 F or
below.
Type 409 Stainless Steel Package
(one or all furnaces)
Heat exchanger tubes and headers
shall be 20-gauge type 409 stainless
steel. The burners and flue collector
shall be 409 Stainless Steel. 409
stainless steel is recommended where
outside air is used for make-up air in
areas where outside temperatures are
40 F or below.
Type 321 Stainless Steel
(one or all furnaces)
Heat exchanger tubes and headers
shall be 20-gauge type 321 stainless
steel. The burners and flue collector
shall be aluminized steel.
Type 321 Stainless Steel Package
(one or all furnaces)
Heat exchanger tubes and headers
shall be 20-gauge type 321 stainless
steel. The burners and flue collector
shall be 409 stainless steel.
Motors - General
All motors shall be ball bearing type
with resilient base mount. Windings
are Class “B”, 1800 rpm with service
factors of 1/2 - 3/4 hp = 1.25 and 1 - 5 hp
= 1.15.
Single-speed Open Drip-proof
60 HZ/1800 RPM
Single-Phase (with contactor) —
Optional 115V, 208V and 230V motors
available in 1/2 - 2 hp models.
Three-Phase (with contactor) —
Optional 208V, 230V and 460V motors
available in 1/2 - 5 hp models.
Single-Phase (with magnetic starter) —
Optional 115V, 208V and 230V motors
available in 1/2 - 3 hp models.
Three-Phase (with magnetic starter) —
Optional 208V, 230V, 460V and 575V
motors available in 1/2 -5 hp models.
Mechanical
Specifications
Single-Speed TEFC
60 HZ/1800 RPM
Single-Phase (with contactor) —
Optional 115V, 208V and 230V motors
available in 1/2 - 1 1/2 hp models.
Single-Phase (with magnetic starter) —
Optional 115V, 208V and 230V motors
available in 1/2 - 3 hp models.
Three-Phase (with magnetic starter) —
Optional 208V, 230V, 460V and 575V
motors available in 1/2 - 5 hp models.
Single-Speed High Efficiency ODP
60 HZ/1800 RPM
Single-Phase (with contactor) —
Optional 115V and 230V motors
available in 1/2 - 1 hp models. Optional
208V motors available in 1/2 - 3/4 hp
models.
Single-Phase (with magnetic starter) —
Optional 115V and 230V motors
available in 1/2 - 2 hp models. Optional
208V motors available in 1/2 - 3/4 hp
models.
Three-Phase (with magnetic starter) —
Optional 208V, 230V and 460V motors
available in 1/2 - 5 hp models. Optional
575V motors available in 1 - 5 hp
models.
Single-Speed High Efficiency TEFC
60 HZ/1800 Rpm
Single-Phase (with contactor) - Optional
115V and 230V motors available in
1
/2 - 11/2 hp models.
Single-Phase (with magnetic starter) Optional 115V and 230V motors
available in 1/2 - 2 hp models.
Three-Phase (with magnetic starter) Optional 230V and 460V motors
available in 1/2 - 5 hp models. Optional
208V and 575V available in 1 - 5 hp
models.
Two-Speed/One Winding Motors
(Three Phase Only)
60 HZ/1800/900 RPM
Three-Phase (with magnetic starter) Optional 208V, 230V and 460V motors
available in 1 - 5 hp models.
Two-Speed/Two Winding Motors
60 HZ/1800/1200 RPM
Single-Phase (with magnetic starter) Optional 115V and 230V motors
available in 1/2 - 1 hp models. Optional
208V motors available in 3/4 - 1 hp
models.
Three-Phase (with magnetic starter) Optional 208V and 230V motors
available in 1/2 - 5 hp models. Optional
460V motors available in 1/2 - 3 hp
models.
Manual Blower Switch
Manual blower switch shall be factory
installed in the electrical cabinet.
DX or Chilled Water Cooling Coils
A direct expansion (DX) or chilled water
coil certified by ARI shall be provided
with the unit (available on
Arrangement K only).
Damper Options
Dampers shall be of the opposed blade
type, constructed of galvanized steel
with neoprene nylon bushings, blades
to be mechanically interlocked.
Optional low leak dampers shall be of
the opposed blade type, construction
of galvanized steel with neoprene
nylon bushings and vinyl blade edge
seals, blades to be mechanically
interlocked.
Outside Air or Return Air/2 pos. Motor/
SR
Units with outside air or return air only
shall be provided with a damper, twoposition spring return damper motor
and controls. The motor shall power
the damper fully open when the unit is
on and fully closed when the unit is off.
OA/RA 2 pos SR
A two-position spring return motor
with interlocked outside and return air
dampers shall be provided. The motor
shall power either the outside air
damper fully open and the return air
damper fully closed or the outside air
damper fully closed and the return air
damper fully open in response to an
outside air temperature sensor. When
the unit is off, the motor will drive the
outside air damper fully closed and the
return air damper fully open.
OA/RA Mod Mtr. with Mixed Air
Control/Min. Pot/Spring Return
A modulating motor with interlocked
outside and return air dampers shall be
provided. The motor shall modulate the
position of the outside and return air
dampers in response to a thermostatic
controller located in the mixed air
stream. Units shall also be provided
with a minimum position
potentiometer for minimum outside air
damper position.
The spring return feature drives the
outside air damper fully closed and the
return air damper fully open when the
unit is off.
84
OA/RA Mod Mtr. with Mixed
Air Control/Spring Return
A modulating motor with interlocked
outside and return air dampers shall be
provided. The motor shall modulate the
position of the outside and return air
dampers in response to a thermostatic
controller located in the mixed air
stream.
The spring return feature drives the
outside air damper fully closed and the
return air damper fully open when the
unit is off.
OA/RA Mod Mtr with Min Pot/
Spring Return
A modulating motor with interlocked
outside and return air dampers shall be
provided. The motor shall position the
outside and return air dampers in
response to a manually set
potentiometer.
The spring return feature drives the
outside air damper fully closed and the
return air damper fully open when the
unit is off.
OA/RA Mod Mtr with Dry Bulb/Mixed
Air Control/Min Pot/Spring Return
A modulating motor with interlocked
outside and return air dampers shall be
provided. The motor shall modulate the
position of the outside and return air
dampers in response to a thermostatic
controller and dry bulb thermostat
located in the mixed air stream. Units
shall also be provided with a minimum
position potentiometer for minimum
outside air damper position.
The spring return feature drives the
outside air damper fully open and the
return air damper fully closed when the
unit is off.
OA/RA Mod Mtr with Enthalpy
Controlled Economizer/SR
A modulating motor with spring return
and interlocked outside and return air
dampers shall be provided. The motor
shall modulate the position of the
outside and return air dampers in
response to an enthalpy controlled
economizer. When the unit is off, the
motor will drive the outside air damper
fully closed and the return air damper
fully open.
Mechanical
Specifications
OA/RA Mod Mtr with Space
Pressure Controller
A modulating motor with spring return
and interlocked outside and return air
dampers shall be provided. The motor
shall modulate the position of the
outside and return air dampers in
response to a pressure sensor located
in the building. When the unit is off, the
motor will drive the outside air damper
fully closed and the return air damper
fully open.
OA/RA Mod Mtr with S-350P
Proportional Mixed Air Control/SR
A modulating motor with spring return
and interlocked outside and return air
dampers shall be provided. The motor
shall modulate the position of the
outside and return air dampers in
response to a solid-state mixed air
sensor and S-350 proportional
controller. When the unit is off, the
motor will drive the outside air damper
fully closed and the return air damper
fully open.
OA/RA Mtr. with External 4-20 mA or
0-10VDC Analog Input/Spring Return
A modulating motor interlocked with
outside and return air dampers shall be
provided. The motor shall modulate the
position of the outside and return air
dampers in response to a 4-10 mA or
0-10VDC signal supplied by an external
DDC controller.
The spring return feature drives the
outside air damper fully closed and the
return air damper fully open when the
unit is shut down.
ASHRAE Cycle I
(OA/RA 2 pos with Warm-up Stat/SR)
A two-position spring return motor
with interlocked outside and return air
dampers shall be provided. The motor
shall power the outside air damper
fully open after a warm-up period
determined by a minimum supply air
temperature sensor when the unit is
on, and fully closed when the unit is
off.
ASHRAE Cycle II (OA/RA Mod with
Warm-up Stat/Mixed Air/Min Pot/
Spring Return)
A modulating motor with interlocked
outside and return air dampers shall be
provided. The motor shall modulate the
position of the outside and return air
dampers in response to a thermostatic
controller located in the mixed air
stream after a warm-up period
determined by a minimum supply air
temperature sensor. Units shall also be
provided with a minimum position
potentiometer for minimum outside air
damper position. When the unit is off,
the motor will drive the outside air
damper full closed and the return air
damper full open.
ASHRAE Cycle III (OA/RA Mod. with
Warm-up Stat/Mixed Air/SR
A modulating motor with spring return
and interlocked outside and return air
dampers shall be provided. The motor
shall modulate the position of the
outside and return air dampers in
response to a thermostatic controller
located in the mixed air stream after a
warm-up period determined by a
minimum supply air temperature
sensor. Units shall also be provided
with a minimum position
potentiometer for minimum outside air
damper position. When the unit is off,
the motor will drive the outside air
damper fully closed and the return air
damper fully open.
Manual Dampers
Units with outside air and return air
shall be provided with manually set
outside and return air dampers.
Firestat
If the temperature reaches the setpoint,
the unit will close all gas valves, return
the dampers to their normal position
and shut down the blower. Automatic
reset.
Return Air Mounted
(setpoint typically 130 F)
Standard on Arrangement B and D.
Utilized on these arrangements as a
reverse airflow switch.
Supply Air Mounted
(setpoint typically 150 F)
Freezestat
The rooftop unit shall be provided with
a freezestat (0-100 F) with the sensing
bulb located in the discharge air stream.
Wired as an interlock to prevent cold air
discharge.
Orifices for Elevations over 2000 Feet
12” Evaporative Media
(Arrangement D only)
12” media shall be provided for the
evaporative cooler.
409 Stainless Steel Furnace Drip Pan
Replaces the standard aluminized steel
furnace drip pan.
85
Double Wall Construction
The construction will consist of a 24gauge inner liner wall with 1-inch 1½
lb. density insulation. Access doors on
the specified side will be hinged and of
the same double wall design. Double
wall is not available on the applicable
evaporative cooler and furnace
sections. Double wall construction will
be provided by the manufacturer on
applicable filter/damper, blower, coil
and plenum cabinets.
Clogged Filter Switch
A clogged filter pressure switch with
adjustable operating range and
normally open switch shall be installed
to sense increased suction pressure by
the blower due to filter obstruction. A
provision for remote indication shall be
provided by terminal block connection
points. Includes a status lamp mounted
in the electrical cabinet.
Horizontal Return
The unit shall be supplied with the
return air opening at or under the
outside air opening location depending
on the air inlet configuration.
Continuous Fan Relay - 24V Coil
DPDT 10A
This relay is provided with a 24 volt coil
and double-pole, double-throw 10 amp
contacts. It plugs into the main
connection PC board in the electrical
cabinet. Included as standard on
Arrangement D and E . May also be
utilized as an exhaust fan interlock.
Interlock Relay - 24/115V Coil
SPDT 10A
This relay has a selectable coil voltage
of 24 or 115 volts and single-pole,
double-throw 10 amp contacts with an
LED on the indicator lamp. The relay is
utilized as an auxiliary relay.
Interlock Relay - 24/115-230V Coil
DPDT 10A
This relay has a selectable coil voltage
of 24, 115 or 230 volts and double-pole,
double-throw 10 amp contacts. Utilized
as an auxiliary relay for general
purpose duty.
High/Low Gas Pressure
Limit Switches
A high pressure and a low pressure
interlock switch and shutoff valve shall
be provided for each furnace section.
High/low gas pressure limits disengage
heating upon detecting either high line
pressure or low manifold pressure.
Mechanical
Specifications
Status Indicator Lamps
(Electrical Cabinet)
Status indicator lamps shall include
power on, blower on and one lamp per
stage of heat mounted in the electrical
cabinet.
Ambient Lockout
Airflow Proving Switch
Hinged Service Access Doors
Optional hinged doors are mounted to
the access side of the standard blower/
filter/damper cabinet and high CFM
filter/damper and blower cabinets in
leau of the standard removable access
doors. The hinged doors include dual
quick opening tool-less latches and full
perimeter gasketing to assure a water
tight seal and door stops to guard
against closure while open. The
remaining Duct Furnace(s), supply
plenum cabinets (if applicable) are
supplied with a standard removable
door. The coil cabinet door utilizes a
special removable vertical split door
allowing for coil access and unit
penetration for coil connections.
Field Installed Accessories
Manual Reset High Limit Switch
The unit shall be provided with a
manual reset high limit switch wired in
series to the lead furnace high limit. If
the setpoint is reached, the gas valve
will close and the blower will continue
to run until the sensed temperature is
below the setpoint.
High Gas Line Pressure Regulator
Reduces main gas line pressure to a
minimum of seven inches WC.
Pressure at the jobsite must be
specified. The regulator is selected to
accommodate that specific pressure.
Remote Control Station
Wall mounted. Provides six LED status
lamps with System On/Off, Fan Auto/
On, Heat Auto/Off, Cool Auto/Off,
Auxiliary On/Off switching and
Modulating damper potentiometer
mounting. Designed for easy
installation with plug-in terminal block
wiring and wall mounting bracket.
(Auxiliary On/Off may be used with the
Evaporative Cooler fill and drain kit)
7-Day Timeclock
Provides single-pole, double-throw
(SPDT) relay output at setpoint time
with a maximum of six setpoints per
day.
24-Hour Timeclock
Provides single-pole, double-throw
(SPDT) relay output at setting time with
maximum 12 setpoints per day.
Disconnect Switch
115V Convenience Outlet
GFI (Ground Fault Convenience Outlet)
is manual reset with a weatherproof
enclosure.
Fill and Drain Kit
Includes three-way valve and relay for
automatic fill and drain for the
evaporative coolers. Optional freezestat
provides automatic shutoff and drain
upon meeting outside air setpoint.
Optional Filters
(One-inch permanent standard)
Two-inch Permanent
Two-inch Throwaway
One-inch 30% Pleated Media
Two-inch 30% Pleated Media
Thermostats
Low voltage room thermostat, single
stage with fan auto-on-switch and
system heat-off cool switch
Low voltage room thermostat, single
stage with fan auto-on switch
Low voltage room thermostat, two
stage with fan auto-on switch and
system off-heat-auto-cool switch
Low voltage programmable room
thermostat, two stage with LCD
display, fan auto-on switch and system
off-heat-auto-cool switch.
Universal tamperproof guard for all
room thermostats
Low voltage duct thermostat, single
stage
Low voltage duct stat, two stage
Room thermostat, electronic
modulating control
Duct thermostat, electronic modulating
control
Duct thermostat, electronic modulating
control with override room thermostat
86
a business of American Standard
www.trane.com
For more information contact your
local office, or e-mail us at
[email protected]
Literature Order Number
MUA-D-3
File Number
PL-AH-MUA-000-D-3-603
Supersedes
MUA-D-3 6/01
Stocking Location
Inland - La Crosse
Trane has a policy of continuous product and product data improvement and reserves the right to change
design and specifications without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement