advertisement
Product Catalog
Split System Air Conditioners
Odyssey ™
R-22 Dry Charge
Heat Pump Condenser — 7.5, 10, 15 and 20 Tons — 60 Hz
May 2014
SSP-PRC027B-EN
Introduction
Trane’s reputation for providing quality comfort solutions continues with the development of the next generation Light Commercial Odyssey Split Systems.
With wide network availability, flexible applications, installation ease, built-in reliability and easy servicing, Odyssey will meet any number of customer applications. Add to that Trane’s outstanding customer service and you have the formula to make Odyssey the clear choice for continued customer satisfaction.
Wide network availability
A broad distribution network provides owners, maintenance personnel, contractors, etc., the means to get their hands on equipment when they need it. Whether it’s an emergency replacement or a new construction project in its infancy stages, Odyssey products meet an array of needs at the right time and right price.
Flexible applications
No matter what the application, Odyssey provides the solution. A broad array of models and tonnages are available with single or dual compressors, single or dual circuits and numerous accessories. Condensing units can be installed on the ground or on a rooftop along with extended piping runs, while air handlers can be free discharge on the ground or horizontally suspended with long duct runs from a ceiling. Should application challenges arise, Odyssey delivers.
Easy to install
Small footprints and low weights combined with factory installed components like TXVs, filter driers, etc., reduce installation time and cost. Colored and numbered wiring and factory tested units make Odyssey the right choice.
Built-in reliability
Keeping in mind that productivity only occurs when equipment is operational,Trane has taken the steps to ensure that Odyssey is up and running. Early indicators such as phase/reversal monitors and loss of charge protection provide diagnostics which prevent failure and provide years of worry-free service and operation.
©2014 Trane All rights reserved SSP-PRC027B-EN
Easy to service
When preventive maintenance or service is required, technicians will find efficient access to both air handlers and condensers. Panels provide complete, easy access coupled with standardized cabinets in which all components are located in proximity. Odyssey’s improved design results in minimum service times and costs.
With these capabilities, Odyssey provides customers high efficiency and superior performance for the best all-around value in the market today.
Copyright
This document and the information in it are the property of Trane, and may not be used or reproduced in whole or in part without written permission. Trane reserves the right to revise this publication at any time, and to make changes to its content without obligation to notify any person of such revision or change.
Trademarks
All trademarks referenced in this document are the trademarks of their respective owners.
SSP-PRC027B-EN 3
4
Table of Contents
SSP-PRC027B-EN
Accessories
Heat Pump Condenser
Table 1.
TWA Accessories
Model
Coil (Hail/Vandal) Guard
BAYGARD058A
BAYGARD060A
BAYGARD061A
BAYHGBP010B
Rubber Isolators
BAYISLT005A (black)
BAYISLT009A (red)
BAYISLT010A (green)
Steel Spring Isolators
BAYISLT023A (red)
BAYISLT024A (black)
BAYISLT025A (yellow)
Low Ambient — On/Off Fan Control (External mount, small cabinets) (a) (b) (c)
BAYLOAMU01B (External Mount, small cabinets) (d)
Used With
TWA090A
TWA120A
TWA180B, TWA240B
All models
TWA090A, TWA120A
TWA180B
TWA240B
TWA090A, TWA120A
TWA180B
TWA240B
(all voltages) TWA090A
BAYLOAMU02B (Internal mount, large cabinets) (all voltages) TWA120A, TWA180B, TWA240B
(a)
(b)
(c)
(d)
Cycles fan on/off, (no modulating).
Quantity of 1 required for each fan (2 total for ).
ReliaTel™ requires onboard EDC function to be disabled when BAYLOAM is used, remove OA sensor from terminal J8-1&2
Kit mounts external to the outdoor unit and operates by sensing ambient and liquid line temperatures.
SSP-PRC027B-EN 5
Model Number Description
Heat Pump Condenser
T W A
1 2 3
120
4 5 6
A
7
3
8
0 0
9 10
*
11
*
12
All products are identified by a multiple-character model number that precisely identifies a particular type of unit. An explanation of the alphanumeric identification code is provided. Its use will enable the owner/operator, installing contractors, and service engineers to define the operation, specific components, and other options for any specific unit. When ordering replacement parts or requesting service, be sure to refer to the specific model number, serial number, and DL number (if applicable) stamped on the unit nameplate.
ucctt T yp
TWA = Split System Heat Pump g C ap
090 = 7.5 Tons (60Hz)
120 = 10 Tons (60Hz)
180 = 15 Tons (60Hz)
240 = 20 Tons (60Hz) ntt S eq
A = Single Compressor, Single Circuit, R-22
B = Dual Compressor, Dual Circuit, R-22 eccttrriic all C
3 = 208–230/60/3
4 = 460/60/3
9 -- 1 0:: F
00 = Packed Stock
S 1 Miin
* = Current Design Sequence
1
* = Current Design Sequence
1
1.
* = sequential alpha character
6 SSP-PRC027B-EN
General Data
Table 2.
General data for 7.5 - 20 ton heat pump, 60 Hz
7.5 Tons
Single Compressor
TTA090A3, A4
10 Tons
Single Compressor
TTA120A3, A4
15 Tons
Dual Compressor
TTA180B3, B4
Compressor
Type
No./Tons
System Data
No. Refrigerant Circuits
Suction Line (in.) OD
Liquid Line (in.) OD
Outdoor Coil
Type
Tube Size (in.) OD
Face Area (sq ft)
Rows/FPI (Fins per inch)
Outdoor Fan
Type
No. Used/Diameter (in.)
Drive Type/No. Speeds
CFM
No. Motor/HP
Motor RPM
Refrigerant Charge (Field
Supplied) lbs of R-22
Shipping Dimensions
HxWxD (in.)
Scroll
1/6.9
1
1.38
5/8
Lanced
0.38
19.2
2/18
Propeller
1/26
Direct/1
6530
1/0.5
1100
17.6
43.54” x 43” x 36.5”
Scroll
1/8.6
1
1.38
1/2
Lanced
0.38
24.0
2/18
Propeller
1/28
Direct/1
9600
1/1
1100
22.5
43.5” x 53” x 40.5”
Scroll
2/6.9
2
1.38
1/2
Lanced
0.38
24.0
2/18
Propeller
2/28
Direct/1
19500
2/1
1100
39.0
49.5" x 94.8" x 47"
20 Tons
Dual Compressor
TTA240B3, B4
Scroll
2/8.6
2
1.38
1/2
Lanced
0.38
24.0
2/18
Propeller
2/28
Direct/1
19500
2/1
1100
43.8
49.5" x 94.8" x 47"
SSP-PRC027B-EN 7
8
1 5 5
1 4 5
1 3 5
1 2 5
1 1 5
1 0 5
9 5
8 5
7 5
6 5
5 5
4 5
3 5
2 5
Performance Data
Table 3.
Gross cooling capacities (MBH) 7.5 tons TWA090A condensing unit only (IP)
Outdoor
Temp (°F)
65
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
30
161.6
75.4
4.8
190.7
35
172.5
83.5
5.0
196.7
Suction Temperature (°F)
40
178.6
92.3
5.1
203.0
45
185.2
101.5
5.3
209.7
50
192.0
111.1
5.5
216.7
75
85
95
105
115
125
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
71.3
5.3
217.1
67.5
5.8
246.4
63.6
6.4
278.2
59.7
7.0
312.8
55.7
7.7
350.1
51.6
8.4
79.2
5.5
223.3
75.0
6.0
252.9
70.8
6.6
285.0
66.5
7.2
319.8
62.1
7.8
357.3
57.7
8.6
87.7
5.6
230.0
83.0
6.1
259.7
78.3
6.7
292.0
73.6
7.4
327.1
68.9
8.0
364.7
64.1
8.7
96.4
5.8
237.0
91.3
6.3
266.9
86.2
6.9
299.4
81.0
7.6
334.6
75.8
8.2
372.5
70.6
8.9
105.5
6.0
244.3
99.9
6.5
274.5
94.4
7.1
307.2
88.7
7.8
342.5
83.1
8.4
380.5
77.3
9.1
Note: Performance data calculated at 15°F subcooling and 15°F superheat and does not include capacity loss due to refrigerant lines.
Figure 1.
TWA090A capacity curve
Ca pa city Curves - Condensing Unit Only
3 0 3 5 4 0 6 0 6 5 7 0
65
75
85
95
105
115
125
7 5 4 5 5 0 5 5
Sa tura te d Suction Te mpe ra ture (F)
55
199.2
121.0
5.6
224.1
114.8
6.2
252.0
108.8
6.7
282.3
102.8
7.3
315.2
96.7
8.0
350.7
90.5
8.6
388.8
84.3
9.3
SSP-PRC027B-EN
13 0
11 5
10 0
85
70
55
25
Table 4.
Gross cooling capacities (MBH) 10 tons TWA120A condensing unit only (IP)
Outdoor
Temp (°F) 30 35
Suction Temperature (°F)
40 45 50
65
Head Press (psig)
Capacity (Btuh/1000)
166.3
98.4
172.1
108.8
178.4
119.9
185.1
131.5
192.3
143.8
75
85
95
105
115
125
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
7.1
189.0
95.0
7.6
213.9
91.2
8.1
241.6
87.2
8.8
272.0
82.8
9.6
305.1
78.1
10.4
340.8
73.2
11.3
7.3
194.9
105.1
7.8
219.9
101.0
8.4
247.7
96.5
9.0
278.2
91.8
9.8
311.3
86.7
10.6
347.1
81.3
11.5
7.5
201.2
115.8
8.0
226.3
111.3
8.6
254.3
106.5
9.2
284.8
101.2
10.0
317.9
95.7
10.8
353.8
89.9
11.7
7.8
207.9
127.1
8.3
233.1
122.2
8.8
261.2
117.0
9.5
291.7
111.3
10.2
324.9
105.2
11.0
360.8
98.8
12.0
8.0
215.1
138.9
8.5
240.4
133.6
9.1
268.5
127.9
9.7
299.1
121.8
10.5
332.3
115.2
11.3
368.2
108.2
12.2
Note: Performance data calculated at 15°F subcooling and 15°F superheat and does not include capacity loss due to refrigerant lines.
Figure 2.
TWA120A capacity curves
Ca pacity Curves - Condensing Unit Only
17 5
16 0
14 5
30 35 40 45
Sa turated Suction Temperature (F)
50 55
65
75
85
95
105
115
125
60
55
9.3
276.2
139.4
10.0
306.9
132.7
10.7
340.1
125.6
11.5
199.9
156.6
8.3
222.7
151.3
8.8
248.1
145.6
375.9
118.0
12.4
SSP-PRC027B-EN 9
275
260
245
230
215
200
185
170
155
140
125
110
95
80
25
Table 5.
Gross cooling capacities (MBH) 15 tons TWA180B condensing unit only (IP)
Outdoor
Temp (°F) 30 35
Suction Temperature (°F)
40 45 50
65
Head Press (psig)
Capacity (Btuh/1000)
149.9
148.9
154.2
167.0
158.9
186.2
164.0
206.9
169.3
228.7
75
85
95
105
115
125
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
10.4
172.4
141.1
11.3
197.3
133.2
12.2
224.8
125.1
13.2
255.2
116.8
14.4
288.4
108.4
15.7
324.5
99.9
17.1
10.6
176.8
158.4
11.5
201.8
149.7
12.4
229.4
140.9
13.5
259.9
131.9
14.7
293.2
122.8
15.9
329.5
113.6
17.3
10.9
181.5
176.8
11.7
206.6
167.3
12.7
234.3
157.6
13.8
264.9
147.9
15.0
298.3
138.1
16.2
334.7
128.1
17.6
11.1
186.6
196.3
12.0
211.6
185.8
13.0
239.5
175.4
14.1
270.2
164.8
15.3
303.7
154.1
16.5
340.1
143.3
17.9
11.4
192.0
217.1
12.3
217.0
205.4
13.3
245.0
194.0
14.4
275.8
182.5
15.6
309.3
170.9
16.9
345.8
159.2
18.2
Note: Performance data calculated at 15°F subcooling and 15°F superheat and does not include capacity loss due to refrigerant lines.
Figure 3.
TWA180B capacity curves
Ca pacity Curves - Condensing Unit Only
30 35 40 45
Sa turated Suction Temperature (F)
50 55
65
75
85
95
105
115
125
60
55
213.5
14.7
281.6
201.0
15.9
315.2
188.4
17.2
175.0
251.4
11.6
197.6
238.9
12.6
222.7
226.2
13.6
250.8
351.7
175.7
18.6
10 SSP-PRC027B-EN
290
275
260
245
230
215
200
185
350
335
320
305
170
155
140
125
110
25
Table 6.
Gross cooling capacities (MBH) 20 tons TWA240B condensing unit only (IP)
Outdoor
Temp (°F) 30 35
Suction Temperature (°F)
40 45 50
65
Head Press (psig)
Capacity (Btuh/1000)
164.1
196.0
169.9
217.1
176.1
239.8
182.8
263.8
189.9
288.9
75
85
95
105
115
125
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
Head Press (psig)
Capacity (Btuh/1000)
Unit Power (kW)
14.3
186.5
187.6
15.3
211.3
178.5
16.4
238.7
168.8
17.7
268.9
158.4
19.2
301.8
147.6
20.9
337.5
136.2
22.7
14.8
192.3
208.1
15.7
217.1
198.3
16.8
244.7
187.8
18.2
275.0
176.7
19.6
307.9
164.9
21.3
343.7
152.7
23.1
15.2
198.6
229.8
16.2
223.4
219.2
17.3
251.1
208.0
18.6
281.4
195.9
20.1
314.4
183.3
21.7
350.2
170.0
23.5
15.7
205.3
253.0
16.7
230.1
241.4
17.8
257.8
229.1
19.1
288.2
216.2
20.5
321.3
202.5
22.2
357.1
188.2
24.0
16.2
212.4
277.4
17.2
237.3
264.8
18.3
265.1
251.6
19.5
295.4
237.4
21.0
328.5
222.7
22.6
364.1
207.1
24.4
Note: Performance data calculated at 15°F subcooling and 15°F superheat and does not include capacity loss due to refrigerant lines.
Figure 4.
TWA240B capacity curves
Ca pacity Curves - Condensing Unit Only
30 35 40 45
Sa turated Suction Temperature (F)
50 55
65
75
85
95
105
115
125
60
55
18.8
272.7
275.1
20.0
303.1
259.9
21.5
336.2
243.8
23.1
197.5
315.2
16.8
219.9
302.8
17.7
245.0
289.3
371.6
226.7
24.8
SSP-PRC027B-EN 11
Electrical Data
Table 7.
Electrical characteristics — compressor and condenser fan motors — heat pumps — 60Hz
Tons
7.5
10
Unit Model
Number
TWA090A3
TWA090A4
TWA120A3
TWA120A4
No.
1
1
1
1
Compressor Motor
Amps
Volts
208-230
460
208-230
460
Phase
3
3
3
3
RLA LRA
(Ea.) (Ea.)
22.4
10.9
30.1
15.5
164
100
225
114
No.
1
1
1
1
Condenser Fan Motor
Amps
Volts
208-230
460
208-230
460
Phase
1
1
1
1
FLA
3.1
1.6
5.0
2.5
LRA
(Ea.) (Ea.)
8.1
3.8
14.4
5.8
TWA180B3 1 208-230 3 22.4
164 2 208-230 2 5.0
14.4
15
TWA180B4 1 460 3 10.9
100 2 460 2 2.5
5.8
TWA240B3 1 208-230 3 30.1
225 2 208-230 2 5.0
14.4
20
TWA240B4 1 460 3 15.5
114 2 460 2 2.5
5.8
Note: Electrical characteristics reflect nameplate values and are calculated in accordance with cULus and ARI specifications.
Table 8.
Unit wiring — heat pumps —60Hz
Tons
7.5
10
15
20
Unit Model
Number
TWA090A3
TWA090A4
TWA120A3
TWA120A4
TWA180B3
TWA180B4
TWA240B3
TWA240B4
Note: HACR type circuit breaker per NEC.
Unit Operating
Voltage Range
187-253
414-506
187-253
414-506
187-253
414-506
187-253
414-506
Minimum Circuit
Ampacity
31.1
15.2
42.6
21.9
60.4
29.5
77.7
39.9
Maximum Fuse or HACR
Circuit Breaker Size
45
25
60
30
80
40
100
50
12 SSP-PRC027B-EN
Dimensional Data
Heat Pump Condenser
Figure 5.
7.5 ton heat pump, single compressor
SEE NOTE 3
SERVICE PANEL
N OTES :
1 . ACCES S OP ENING IS FOR FIELD INS TALLED BAYLOAM ACCES S ORY.
2 . MINIMUM CLEARANCE FOR P ROP ER OP ERATION IS 36" ( 914.4) FROM
WALLS , S HRUBBERY, P RIVACY FENCES ETC. MINIMUM CLEARANCE
B ETWEEN ADJ ACENT UNITS IS 72" (1828.8). RECOMMENDED S ERVICE
C LEARANCE 48" (1219.2)
3 . TOP DIS CHARGE AREA S HOULD BE UNRES TRICTED FOR 100" (2540)
M INIMUM. UNIT S HOULD BE P LACED S O ROOF RUN-OFF WATER DOES
NOT P OUR DIRECTLY ON UNIT
4 . OUTDOOR AIR TEMP ERATURE S ENS OR OP ENING (DO NOT BLOCK OP ENING)
H AIL GUARD
( OP TIONAL)
SEE NOTE 4
HAI L GUARD
(OP TIONAL)
S ERVICE CLEARANCE
48" (1219.2) (S EE NOTE 2
F OR CLEARANCE)
LINE VOLTAGE
CONT ROL WIRING
LIQUID LINE
SUCTION LINE
WIT
35 15
33 15
/16"
(912.8 )
H HAIL GUARD
/16"
(86 2)
S EE NOTE 1
R EFRIGERANT ACCES S
5 5/8"
(143)
8 5/16"
(211.1)
29 13/16"
(757.2)
36 3/8"
(923.9)
SER VICE P ANEL
3 9 3/16"
(995.4)
2 6 15/16"
(684.2)
1 4 3/8"
(365.1)
1/16"
(1.6)
3" (76. 2)
6 "
(152 .4)
21 11 /16"
(55 0.9)
33 13/1 6"
(858 .8)
SERVIC E P ANEL S IDE
6"
(152 .4)
3 1/16" (77.8)
2 " (50.8)
W
41 1/16"
(1043)
4 2 1/8"
(1070)
ITH HAIL GUARD
7/16" (11.1) DIA. IS OLATOR MOUNTING
H OLES (OUTS IDE HOLES - 4 P LACES )
40 3/4"
(1035)
34 3/4"
(882.7)
B
O
OTTOM
F UNIT
4 3/16"
(106.4)
1 13/16"
(46)
27 11/ 16"
(703.3 )
2 5/16"
(58.7)
SSP-PRC027B-EN 13
Figure 6.
10 ton heat pump, single compressor
SEE NOTE 3
SERVICE PANEL
SEE NOTE 4
N OTES :
1 . ACCES S OP ENING IS FOR FIELD INS TALLED BAYLOAM ACCES S ORY.
2. MINIMUM CLEARANCE FOR P ROP ER OP ERATION IS 36" (914.4) FROM
WALLS , S HRUBBERY, P RIVACY FENCES ETC. MINIMUM CLEARANCE
BETWEEN ADJ ACENT UNITS IS 72" (1828.8). RECOMMENDED S ERVICE
CLEARANCE 48" (1219.2)
3 . TOP DIS CHARGE AREA S HOULD BE UNRES TRICTED FOR 100" (2540)
MINIMUM. UNIT S HOULD BE P LACED S O ROOF RUN-OFF WATER DOES
NOT P OUR DIRECTLY ON UNIT
4. OUTDOOR AIR TEMP ERATURE S ENS OR OP ENING (DO NOT BLOCK OP ENING)
HAI L GUARD
(OP TIONAL)
H AIL GUARD
(OP TIONAL)
S ERVICE CLEARANCE
48" (1219.2) (S EE NOTE 2
F OR CLEARANCE
4 1/4" (108)
1 1/4" ( 31.7)
LINE VOLTAGE
CONTROL WIRING
3 9 15/16"
(1014.4)
WIT H HAIL GUARD
37 15 /16"
(96 3.6)
S EE NOTE 1
R EFRIGERANT ACCES S
LIQUID LINE
SUCTION LINE
5 9/16"
(141.3)
8 1/4"
(209.5)
35 3/4"
(908)
42 5/16"
(1074.7)
1/16" (1.6)
6" (152. 4)
4" (101. 6)
4 3/8" (111.1)
S ERVICE P ANEL
25 11 /16"
(65 2.5)
37 11 /16"
(95 7.3)
SERVI CE P ANEL S IDE
3" (76. 2)
4 4 3/4"
(1136.6)
3 2 7/8"
(835)
1 4 5/16"
(363.5)
6" (152. 4) 1 13/16" (46)
2 7/8" (73)
7 /16" (11.1) DIA. IS OLATOR MOUNTING
H OLES (OUTS IDE HOLES - 4 P LACES )
5 0 15/16"
(1293.8)
5 1 15/16"
(1319.2)
W ITH HAIL GUARD
50 3/4"
(1289)
44 3/4"
(1136.6)
B
O
OTTOM
F UNIT
2 3/16"
(55.6)
3 13/16 "
(96.8)
31 11 /16"
(80 5)
1 11/16"
(42.9)
14 SSP-PRC027B-EN
Figure 7.
15-20 ton heat pump, dual compressor
SEE NOTE 2
HAI L GUARD
(OP TIONAL)
N OTES :
1 . MINIMUM CLEARANCE FOR P ROP ER OP ERATION IS 36" (914.4) FROM
WALLS , S HRUBBERY, P RIVACY FENCES ETC. MINIMUM CLEARANCE
B ETWEEN ADJ ACENT UNITS IS 72" (1829). RECOMMENDED S ERVICE
C LEARANCE 48" (1219.2)
2 . TOP DIS CHARGE AREA S HOULD BE UNRES TRICTED FOR 100" (2540)
M INIMUM. UNIT S HOULD BE P LACED S O ROOF RUN-OFF WATER DOES
NOT P OUR DIRECTLY ON UNIT
3 . OUTDOOR AIR TEMP ERATURE S ENS OR OP ENING (DO NOT BLOCK OP ENING).
SEE NOTE 3
S ERVICE CLEARANCE
48" (1219.2) (S EE NOTE 1
FOR CLEARANCE)
DETAIL A
95 7/16"
(2424.112)
WITH HAIL GUARD
SERVICE PANEL
46"
(1168. 4)
WITH HAIL GUARD
4 4 3/16"
(1122.4)
HAI L GUARD
(OP TIONAL)
H AIL GUARD
( OP TIONAL)
45 1/8"
(1146.2)
SER VICE
P ANEL
3" (76. 2)
93 5/16"
(2370.1)
87"
(2210)
93"
(2362.2)
41 3/8"
(1051)
7/16" (11.1) ( DIA. ISOLATOR MOUNTING
H OLES (OUTS IDE HOLES - 4 P LACES )
SERVICE PANEL SIDE
BOTTOM OF UNIT
1 /16"
(1.6)
C ONTROL WIRING
L INE VOLTAGE
9 "
(228.6)
2 5 11/16"
(652.5)
9 "
(228.6)
9 1/4" (235)
6 13/16" (173)
1 3/16" (30.2)
R EFRIGERANT ACCES S
3 9 7/8"
(1012.8)
4 1 5/8"
(1057.3)
36 7/8"
(936.6)
41 1/ 2"
(1054 .1)
1 4 1/2"
(368.3)
1 4 5/8"
(371.5)
1 2 5/8"
(320.7)
5 5/8"
(143)
4 1/4"
(108)
SUCTI ON LINES
2 3/16"
(55.6)
6 13/16"
(173)
FRO NT DETAIL A
D IMENS IONAL DETAIL
LIQUID LINES
1 5/16" (23.8)
3 11/16" (94)
6 5/16" (160.3)
SSP-PRC027B-EN 15
Weights
Heat Pump Condenser
Table 9.
TWA unit and corner weights — lbs (60 Hz)
Tons
7.5
10
15
20
Model No.
Shipping
Max (lbs)
TWA090A
TWA120A
TWA180B
TWA240B
394
509
898
981
Net Max
(lbs)
340
438
765
848
1
117
127
202
254
Figure 8.
TWA090, 120
#3
#4
#1
#2
Corner Weights
2
86
121
192
266
3
58
72
181
147
Figure 9.
TWA180, 240
#4
4
79
118
190
181
#1
S ER
ACC
VICE
ESS
S ER
ACC
ESS
S ER
ACC
VICE
ESS
LIFTING HOLES
(BOTH S IDES )
LIFTING HOLES (BOTH S IDES )
#2
#3
16 SSP-PRC027B-EN
SSP-PRC027B-EN 17
18 SSP-PRC027B-EN
SSP-PRC027B-EN 19
Trane optimizes the performance of homes and buildings around the world. A business of Ingersoll Rand, the leader in creating and sustaining safe, comfortable and energy efficient environments, Trane offers a broad portfolio of advanced controls and HVAC systems, comprehensive building services, and parts. For more information, visit www.Trane.com
.
Trane has a policy of continuous product and product data improvements and reserves the right to change design and specifications without notice.
©2014 Trane All rights reserved
SSP-PRC027B-EN 19 May 2014
Supersedes SSP-PRC027-EN (June 2012)
We are committed to using environmentally conscious print practices that reduce waste.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project