TRENDnet TE100-P21 User's Manual

TRENDnet TE100-P21 User's Manual
TABLE OF C ONTENTS
ABOUT THIS GUIDE .................................................................................. 5
INTRODUCTION......................................................................................... 6
PACKAGE CONTENTS .................................................................................... 7
SYSTEM REQUIREMENTS ............................................................................... 7
GENERAL FEATURES ..................................................................................... 8
PRODUCT VIEW............................................................................................. 9
HARDWARE INSTALLATION ............................................................... 11
NETWORKING APPLICATION ....................................................................... 11
INSTALLING THE PRINT SERVER .................................................................. 12
USING THE UTILITIES ........................................................................... 13
AUTO-RUN INSTALLATION ......................................................................... 13
PS-UTILITY ................................................................................................. 15
Installing PS-Utility ................................................................................ 15
Using PS-Utility...................................................................................... 16
PS WIZARD ................................................................................................. 19
PSM SETUP UTILITY ................................................................................... 22
Installing of HP LaserJet1000 in Win 98 ............................................... 26
Installing of HP LaserJet1000 in Win 2000 ........................................... 30
Installing of HP LaserJet1000 in Win XP............................................... 37
WEB CONFIGURATION.......................................................................... 43
WEB CONFIGURATION UTILITY .................................................................. 43
MANAGEMENT ............................................................................................ 44
Management J System........................................................................... 45
Management J Network ........................................................................ 47
Management J User .............................................................................. 50
CONFIGURATION ......................................................................................... 51
Configuration J System ......................................................................... 51
-2-
Configuration J Network....................................................................... 54
Configuration J User ............................................................................ 57
Configuration J E-mail ......................................................................... 58
Configuration J SNMP.......................................................................... 60
TOOLS ......................................................................................................... 61
Tool J Print Test.................................................................................... 61
Tool J E-mail......................................................................................... 62
Tool J Reset........................................................................................... 63
Tool J Factory Reset ............................................................................. 64
Tool J Firmware Upgrade .................................................................... 65
Tool J Backup ....................................................................................... 66
HELP ........................................................................................................... 67
PRINTING IN WINDOWS 95/98/ME ...................................................... 68
INSTALLING THE LPR FOR TCP/IP PRINTING CLIENT ................................. 69
ADDING LPR PRINTER PORTS ..................................................................... 71
PRINTING FROM WINDOWS 95/98/ME ........................................................ 73
SETTING TCP/IP PRINTING SETTINGS ......................................................... 76
PRINTING IN WINDOWS 2000/XP ........................................................ 78
SETTING UP WINDOWS 2000 TCP/IP PRINTING .......................................... 78
SETTING UP WINDOWS XP TCP/IP PRINTING............................................. 87
PRINTING IN MAC OS ............................................................................ 96
RENDEZVOUS USES IN MAC OS 10.2 ......................................................... 96
SETTING UP APPLE TALK/LPR PRINTING ................................................... 99
For MAC OS X User............................................................................... 99
For MAC OS 9 User ............................................................................. 101
For MAC OS 9 User ............................................................................. 102
PRODUCT SPECIFICATIONS .............................................................. 105
Printer Connection ............................................................................... 105
Network Connection ............................................................................. 105
Network Protocol Support .................................................................... 105
Hardware .............................................................................................. 106
Operating System Support .................................................................... 106
Management ......................................................................................... 106
LEDs ..................................................................................................... 106
-3-
Environmental and Physical ................................................................. 107
EMI Compliance ................................................................................... 107
-4-
A BOUT THIS G UIDE
This manual provides instructions and illustrations on how to use your
Print Server, including:
z
Chapter 1, Introduction, provides the general information on
the product.
z
Chapter 2, Hardware Installation, describes the hardware
installation procedure for the product.
z
Chapter 3, Using the Utilities, helps you to install and use the
software.
z
Chapter 4, Web Configuration, completes the configuration
using the web browser.
z
Chapter 5, Printing in Windows 95/98/ME, completes the
printing TCP/IP setting in Windows 95/98/ME environment.
z
Chapter 6, Printing in Windows 2000/XP, completes the
printing TCP/IP Setting in Windows 2000/XP environment.
z
Chapter 7, Printing in MAC OS, lets you complete printing task
through your print server in MAC OS environment.
z
Chapter 8, Product Specification.
Please note that the illustrations or setting values in this manual are
FOR YOUR REFERENCE ONLY. The actual settings and values
depend on your system and network. If you are not sure about the
respective information, please ask your network administrator or MIS
staff for help.
-5-
1
I NTRODUCTION
Congratulations on purchasing your TE100-P21 Print Server, the
easiest and fastest way to deploy printers on your network.
This print server can connect your network through an Access Point
under the infrastructure mode, or can be used in ad-hoc mode for
direct communication between PC/Notebook and print server
anywhere you wish to locate wireless printer services. It manages
the flow of print files from your workstation or file server to its
connected printers, delivering print jobs to high-performance printers
much faster than a file server or a PC acting as a print server can.
The Print Server features a Web-based Configuration Utility, which
allows you to set up the print server through the web browser easily
and quickly. It also includes a powerful software utility PS-Utility
and PS Monitor Setup, the user-friendly program that allows you to
complete further settings for the print server.
-6-
Package Contents
Unpack the package and check all the items carefully, and be certain
that you have:
♦ One TE100-P21 Print Server.
♦ One Quick Installation Guide.
♦ One Installation CD-ROM containing the PS-Utility & PS Monitor
Setup program and User’s Guide.
♦ One AC Power Adapter suitable for your country’s electric power
service.
If any item contained is damaged or missing, please contact your local
dealer immediately. Also, keep the box and packing materials in
case you need to ship the unit in the future.
System Requirements
♦ Operating System:
Microsoft Windows 95/98/ME/NT/2000/XP/2003.
Apple Mac OS (with Apple Talk support).
♦ For Web Configuration:
Java-enabled web browser, such as Microsoft® Internet
Explorer 5.0 and Netscape Navigator 6.0.
-7-
General Features
♦ Equipped with 1 parallel port and 2 USB ports allows user to share
three printers on LAN simultaneously.
♦ Compliant with USB 2.0 High-speed printing.
♦ Equipped one 10/100 auto-MDIX Fast Ethernet LAN port.
♦ Multi protocol support is ideal for shared printing in mixed-LAN
environments.
♦ Windows-based administrative program makes it possible to set up
in a few steps.
♦ Latest MIB-II (RFC 1213) for SNMP standard management.
♦ Offer LPR program for Windows 95/98/Me TCP/IP printing.
♦ IP assignment support for DHCP, BOOTP and RARP.
♦ Support Web configuration.
♦ Provide Flash memory for easy firmware upgrade.
♦ Printing Access control and display.
♦ E-mail notification for printer error messages.
♦ Support E-Mail printing and FTP printing.
♦ Ability to save print server configuration into hard drive for easy
access and backup without the hassle to reconfigure if setting
is altered.
♦ Support IPP printing for Windows 2000/XP.
♦ Support Microsoft Graphical Device Interface (GDI) Printer
♦ Support second http port for remote web configuration and IPP
printing.
♦ Support UPnP (Universal Plug and Play) for Windows XP.
♦ Support Mac OS 10.2 “Rendezvous” zero-configuration function.
-8-
Product View
This section describes the externally visible features of the print
server.
Front View
LEDs*
Rear View
LPT Port – connect the
print server to a LPT printer.
LAN Connector –
plug your LAN cable
to this connector.
DC Power Input –
plug the AC Power
Adapter to this jack.
Reset Button**
USB Port – connect the
print server to a USB printer.
-9-
* There are five green LED indicators on the front panel:
LEDs
Description
Power
Steady light means power on.
USB1
When it is blinking, the connected printer is
printing.
USB2
When it is blinking, the connected printer is
printing.
LPT
When blinking, the connected printer is printing.
LAN
Steady light means the print server has been
connected to the network.
When blinking (briefly dark), the print server is
receiving/ transmitting data from/to the network.
**Reset Unit
•
Press and release reset button to reset the print server
Restore to Factory Default
•
Press and hold this button for three seconds (the USB LED on
the front panel will light up) and then release it, the print
server will restore to factory default settings.
- 10 -
2
H ARDWARE
I NSTALLATION
Networking Application
The following diagram explains the application of your print server.
Print Server
- 11 -
Installing the Print Server
Follow these steps for a trouble-free start of print server operations
with your Print Server.
1. Confirm that your network is operating normally.
2. Connect the print server to the network (through the RJ-45
connector of the print server).
5. While the printer is powered off, connect the print server to the
printer’s USB or Parallel port.
6. Turn on the printer’s power.
7. Connect the DC end of the AC Power adapter to the DC power
input socket of the print server and the AC end to the wall outlet.
This will supply power to the print server immediately.
NOTE: This print server is built-in with a default IP Address (e.g.
192.168.0.1). To prevent from any conflict in your network, it is
recommended to use the PS-Utility program to change the IP
setting when there is some other device’s IP Address is the same
as the print server’s default IP Address.
- 12 -
3
U SING T HE U TILITIES
This chapter describes the software utilities for the print server,
including how to set up your print server with these utility. The PSUtility and PS Wizard are designed with a user-friendly interface that
allows you to set up and administer the print server easily.
Auto-Run Installation
Insert the Installation CD-ROM into your computer’s CD-ROM drive
to initiate the Auto-Run program, and the menu screen will appear as
below.
- 13 -
• Manual – click to preview the User's Guide in PDF format for
detailed information of the Print Server.
• Install Utility – click to install PS-Utility. Please refer to the
next section for detailed information on installing the utility.
• PS Wizard – click to launch the Printer Wizard program, which
is helpful to set up the printer configuration easily and quickly.
• PS Monitor Setup – Click to launch the PSM Program to
support GDI printer.
• Browse CD – if you want to browse the contents of the
Installation CD-ROM, click this button and the contents of the
CD will be available for preview.
• Exit – click to close the Auto-Run program.
- 14 -
PS-Utility
To avoid the conflict in your network, you can use PS-Utility to
change the related settings of your print server (such as the IP address)
after finishing the installation.
Installing PS-Utility
1. Click Install Utility from the Auto-Run menu screen. Once
executed, the Setup program will extract files to launch the
InstallShield Wizard; then, click Next > in the welcome screen of
InstallShield Wizard.
2. Choose the destination location. If no specific requirement,
leave the default setting and click Next >.
- 15 -
3. The InstallShield Wizard starts to install the software, and the
Progress bar indicates the installation is proceeding.
4. When completed, click Finish.
After installing the utility, the application program for the print server
is automatically installed to your computer, and creates a folder in
Start\Programs\PS-Utility.
Using PS-Utility
This section describes the operation of PS-Utility.
Utility:
To launch PS-
1. Click Start -> Programs -> PS-Utility, and then click the PSUtility v3.00 item.
- 16 -
2. The main screen will appear as below, and it starts to search the
connected print server within the network.
Your print server
Component Features:
1. Device List: Display the connected print server within the
network.
2. Control Buttons
- Setup Wizard: Click the button to set up the print server’s
system setting, IP Address, Workgroup of Microsoft Network
and apple talk setting.
- Update Firmware: Click this button to update the firmware of
the selected print server.
- 17 -
-
-
-
Change IP Address:
Click this button to
bring up the following
dialog box, allowing
you to change the IP
Address. In this dialog
box, you can select
either Manually Assign
or DHCP Assign
Automatically. When
completed, click OK.
Factory Reset: Click this button to reload the factory settings
of the print server.
Show Web Setup: Click this button to open your web
browser and launch the Configuration Utility. Alternately,
you can double-click the print server in the Device List to
launch the Configuration Utility.
Discover Device: Click this button to search the connected
print server again.
About: Click this button to bring up a window containing the
basic information of PS-Utility.
Close: Click this button to exit PS-Utility.
3. Information Field: Display the basic information of the selected
print server in the Device List.
4. Status Bar: Display the system status.
- 18 -
PS Wizard
PS Wizard is a convenient utility that allows you to set up the print
server’s port connection.
To launch PS Wizard:
1. Insert the Installation CD-ROM into your computer’s CD-ROM
drive, and click PS Wizard from the Auto-Run menu screen.
The welcome screen appears as below. Click Next >.
NOTE: For some specific printers, you may need to connect the
printer to the computer and install the driver. In this case, connect
it to the computer and install the driver first, and then connect it to
the print server.
- 19 -
2. In the following window, select one printer in the Printer List to
set up port connection, and then click Next >.
Choose one connected
printer within the network.
3. Select one printer port in the Print Server List, and click Next >.
Your print server name
Your printer port name
- 20 -
Choose one connected
printer port.
4. The configuration is completed, click Reboot and then Yes to
restart the system.
After rebooting, PS Wizard will help you to complete the port
connection automatically. You can start your printing task
without any complex configuration.
TIP: If you use Windows 2000/XP, the system will not restart to
complete the installation.
- 21 -
PSM Setup Utility
PS Monitor will allow the print server to support HP GDI Printers.
1. Click the “PS Monitor Setup” program from the CD-ROM. This
program will lead you to finish the installation process of the PS
Monitor step by step.
2. Choose the Language of your Windows system and click the
“OK” button to the next step.
- 22 -
3. Click the “Next” button and start to install the PS Monitor.
4. Specified the directory for of the PS Monitor to be installed inside
and then click the “Next” button.
- 23 -
5. Click the “Finish” button to complete the installation.
- 24 -
6. The installation is completed. Click the “Start”->”Program”->”PS
Monitor”->”PS Monitor 1.30” to launch the PS Monitor.
7. To verify if the PS Monitor is executed successfully, please check
that the icon of PS Monitor is shown in the right side of bottom
bar under your Windows system.
- 25 -
Installing of HP LaserJet1000 in Win 98
1. Open the “Printers” window of your Windows 98 system and
click the “Add Printer” function. The following window will be
popped up. Click the “Next” button to the next step.
2. Select the “Network Printer”. Click “Next” button to the next step.
- 26 -
3. Specify the port name of the printer server. The syntax is
“\\Printer Server name\Printer port name of the printer server”
as the following show. Click the “Next” button to the next step.
- 27 -
4. Choose the driver form the list or insert the HP LaserJet 1000 CDROM. Click the “Next” button to the next step.
- 28 -
5. If necessary, you could modify the name for the printer added.
The installation is completed by clicking the “Finish” button.
- 29 -
Installing of HP LaserJet1000 in Win 2000
1. Open the “Printers” window of your Windows 2000 system and
click the “Add Printer” function. The following window will be
popped up. Click the “Next” button to the next step.
2. Select the “Local printer” and uncheck the “Automatically detect
and install my Plug and Play printer”. Click “Next” button to the
next step.
- 30 -
6. Select the “Create a new port” and specify the type of port as
“Local Port”. Click the “Next” button to the next step.
- 31 -
3. The following window will be popped up for you to specify the
port name of the printer server. The syntax is “\\Printer Server
name\Printer port name of the printer server” as the following
show. Click the “OK” button to the next step.
4. Please specify the location of the driver of your HP LaserJet 1000
according to your condition. Click the “Next” button to the next
step.
- 32 -
7. Name your printer if necessary. Click the “Next” button to the
next step.
- 33 -
8. Select “Do not share this printer”. Click the “Next” button to the
next step.
- 34 -
9. Select “No” for printer test. Click the “Next” button to the next
step.
- 35 -
10. The installation is completed by clicking the “Finish” button.
- 36 -
11. Select the HP Laser Jet 1000 just been added and open the
“Property” of it.
Click the “Ports” menu and uncheck the “Enable bidirectional
support” to make the printing successful.
Installing of HP LaserJet1000 in Win XP
1. Open the “Printers and Fax” window of your Windows System
and click the “Add Printer” function. The following window will
be popped up. Click the “Next” button to the next step.
- 37 -
2. Select the “Local printer attached to this computer” and uncheck
the “Automatically detect and install my Plug and Play printer”.
Click “Next” button to the next step.
- 38 -
3. Select the “Create a new port and specify the type of port as
“Local Port”.
Click the “Next” button to the next step.
4. The following window will be popped up for you to specify the
port name of the printer server. The syntax is “\\Printer Server
name\Printer port name of the printer server” as the following
show. Click the “OK” button to the next step.
5. Please specify the location of the driver of your HP LaserJet 1000
according to your condition. Click the “Next” button to the next
step.
- 39 -
6. Name your printer if necessary. Click the “Next” button to the
next step.
- 40 -
7. Select “No” for printer test. Click the “Next” button to the next
step.
8. The installation is completed by clicking the “Finish” button.
- 41 -
9. Select the HP LaserJet 1000 just been added and open the
“Property” of it. Click the “Ports” menu and uncheck the “Enable
bidirectional support” to make the printing successful.
- 42 -
4
W EB C ONFIGURATION
You can access and manage the Print Server through: 1) the enclosed
software PS-Utility, and 2) a web browser. This chapter describes
the second method – the Web Configuration Utility, and explains how
to set up your print server with the web browser.
Web Configuration Utility
First, launch your web browser (such as the Internet Explorer 6.0 used
in this manual). Then, type http://192.168.0.1 (the default IP
address) in the Address bar and press [Enter] to enter the Management
screen of the Configuration Utility.
TIP: The computer’s IP address must correspond with the print
server’s IP address in the same segment for the two devices to
communicate. Extensive knowledge of LAN will be helpful in
configuring the print server.
- 43 -
Management
The Management Screen of the Configuration Utility
- 44 -
The Management screen displays the basic information of the print
server, including the following four categories:
z System
z Network
z User
Management J System
As shown above, the System displays the status of your print server,
printer, and network. Clicking Refresh will update the information.
Device Status
The information about the print server, including the firmware
version, MAC/IP address, and up time, can be found in this field.
Printer Status
The items in this field display the information of the printer, such as
the given name for the printer, speed, printer status, and status of your
printing tasks, etc.
- 45 -
Ethernet Status
You can monitor the networking status in this field, including the
network connection, speed, and the packets status.
- 46 -
Management J Network
Click the Network item to display the information of the LAN.
Clicking Refresh will update the information.
- 47 -
Auto IP
This field contains the current settings of TCP/IP, including
DHCP/BOOTP, UPnP, and MAC Rendezvous. The items in this
field are configured in Configuration > Network > TCP/IP.
TCP/IP Printing
In this field, you can monitor the status of your printing tasks through
TCP/IP.
- 48 -
Microsoft Network Printing
In this field, you can monitor the status of your printing tasks through
Microsoft Network.
MAC AppleTalk Printing
In this field, you can monitor the status of your printing tasks through
MAC AppleTalk.
- 49 -
Management J User
Click the User item in the left column to display the user(s)
information.
Users Printing Log
The items in this field display the user(s) information, which include
the user(s) MAC address, IP address, name, and status of printing
tasks.
- 50 -
Configuration
Configuration J System
System Device
In this field, you can configure the basic information of your print
server.
- 51 -
-
Server Name: Assign a name to the print server.
Location (optional): Assign a location for the print server
Admin Contact (optional): Assign the Admin Contact’s name for
the print server.
Password: Enter the Administrator password (3-8 characters).
To set up the password, please enter the password in the New
Password box, and then enter the same one again in the Confirm
Again box.
Port Settings
In this field, you can assign the Port Name for the print server, and
the description for the USB port. It also allows you to select the PJL
Printer setting (Yes or No).
- 52 -
NOTE: PJL (Print Job Language) has certain job requirements that
must be met to work correctly. For more information, please refer
to your printer’s manual.
- 53 -
Configuration J Network
- 54 -
TCP/IP
This field contains three options that allow you to configure the
TCP/IP setting: IP Address, UPnP, and MAC Rendezvous.
-
-
IP Address: This option allows you to set the IP address
manually or automatically. When you choose Manually Assign,
you should enter the related information in the following boxes,
including IP Address, Subnet Mask, and Default Gateway.
UPnP: This option allows you to enable or disable UPnP mode.
MAC Rendezvous: This option allows you to enable or disable
MAC Rendezvous mode.
Microsoft Network
Enter the name of the Workgroup that you want the print server
associated with in this field.
- 55 -
AppleTalk
Enter the AppleTalk Zone name in the box. In the following options,
enter the related configuration, such as the printer type.
-
USB1, USB2, LPT3
• Chooser Name: Display the print server’s Port name.
• Printer Type: Enter the printer’s type in this box.
• PostScript Level: Select from the pull-down menu (Level 1
or Level 2).
• Font Group: Select from the pull-down menu.
- 56 -
TIP: Once you have changed the settings in each option, click
Save to store the settings, or Cancel to abandon.
Configuration J User
Printing Control
By configuring the Enable User Printing Control option (Yes or
No), the user in the User List is permitted to access the print server or
not. For the user(s) who is not in the User List, you can also limit
the access right by setting the Allow Undefined Users Printing
option to Yes or No.
- 57 -
Define Users
You can add/delete the user(s) to/from the User List. The User List
at the bottom of the screen displays the current defined user and
related information for the print server.
TIP: Once you have changed the settings in each option, click
Save to store the settings, or Cancel to abandon.
Configuration J E-mail
- 58 -
E-mail Account
You can assign an E-mail address to the print server, so that your mail
of the account can be printed out directly through the printer (ASCII
text only). To enable this function, enter the E-mail account in the
Print Server E-mail Address box.
-
Incoming E-mail (POP3) Server Address: Enter the server
address that is used to receive your E-mail in this box.
Outgoing E-mail (SMTP) Server Address: Enter the server
address that is used to send your E-mail in this box.
If your mail server needs to verify the user when sending E-mail, you
have to input the Account Name and Password.
E-mail Notification
You can set the print server to send an alter message when the printer
status changes through E-mail. To enable this function, set the
Enable e-mail notification for printer status changing option to
Yes. Then, input the administrator’s E-mail address in the Admin Email Address box.
E-mail Printing
-
E-mail Printing (ASCII Text Only): Select Enable to enable the
E-mail printing function.
Receive E-mail Interval: Enter the number in this box to set up
the time (in minute) to check/receive E-mail regularly.
TIP: Once you have changed the settings in each option, click
Save to store the settings, or Cancel to abandon.
- 59 -
Configuration J SNMP
SNMP Management
SNMP (Simple Network Management Protocol) is a set of protocols
for managing complex networks
-
Community 1/2/3: Enter a name in the Name box, and configure
the Access Right by selecting Read Only or Read/Write from the
pull-down menu.
TIP: Once you have changed the settings in each option, click
Save to store the settings, or Cancel to abandon.
- 60 -
Tools
Tool J Print Test
Print Test
Choose one of the print ports and click Test to print a test page.
- 61 -
Tool J E-mail
Test E-mail Account
Click Test to send a test E-mail to the given administrator’s E-mail
address.
Receive E-mail
Click Yes to immediately check and receive E-mail, and then print
out the mail when available.
- 62 -
Tool J Reset
Reset
Click Yes to immediately reset the print server.
- 63 -
Tool J Factory Reset
Factory Reset
Click Yes to reload the factory settings of the print server.
- 64 -
Tool J Firmware Upgrade
Firmware Upgrade
When a new version of firmware is available (e.g. downloading from
the manufacturer’s website), you can upgrade the firmware of your
print server. Click Browse to point to the firmware file, and then
click Upgrade.
- 65 -
Tool J Backup
Backup Device Configuration to File
Click Backup to backup your current configuration of the print
server to file and then save in the computer.
Restore Device Configuration from File
You can reload a configuration that you saved before.
Browse to point to the backup file, and then click Restore.
- 66 -
Click
Help
This screen displays the information of the print server.
- 67 -
5
P RINTING
IN
W INDOWS
95/98/ME
The Print Server can provide print services to TCP/IP networks using
the LPR/LPD network printing protocol. Most UNIX systems are
capable of supporting LPD, as is Windows NT/2000.
This LPR for TCP/IP Printing client gives Windows 95/98/ME
workstations the ability to print using the LPR/LPD printing protocol.
Though it is possible to print to Print Servers from Windows
95/98/Me, this capability is useful if primarily administer your
network from UNIX systems, or if you want to print from workstations
that are only accessible through IP routing.
- 68 -
Installing the LPR for TCP/IP
Printing Client
Before your Windows 95/98/ME workstation can print using the LPR
protocol, you will need to install the client program, as follows:
1. Make sure that you have installed the TCP/IP protocol, and
have properly configured the Windows 95/98/ME TCP/IP
settings. You can install the protocol from the Network
control panel if necessary.
2. From the Start menu, choose the Settings submenu, then the
Control Panel item within it.
Control Panel folder.
Windows will display the
3. Double-click on the Network icon in the Control Panel folder.
4. Click on the Add... button on the Configuration tab.
5. Windows will ask for the type of component to add. Select
Client and click Add... to continue.
6. When Windows asks you to select a network client, click the
Have Disk... button.
- 69 -
7. Insert the Print Server installation CD in your computer’s CDROM, enter the proper pathname (for example , D:\ lpr), and
click OK.
8. Select the LPR for TCP/IP Printing client and click OK.
9. Windows will copy the necessary files, and return to the
Network dialog.
Click OK to let Windows restart.
- 70 -
Adding LPR Printer Ports
Once you have installed the client, and have enabled TCP/IP printing
for the Print Servers, then you need to add a printer port for each
printer you will be printing to using the lpr/lpd protocol. To add a
printer port,
1. From the Start menu, choose the Settings submenu, then the
Control Panel item within it.
Control Panel folder.
Windows will display the
2. Double-click on the Network icon in the Control Panel folder.
3. Choose the LPR for TCP/IP Printing client and click the
Properties button.
- 71 -
4. Click the Add Port... button to add a new lpd-accessible printer
port.
5. Enter the IP address of the Print Server and the name of the
printer port that you will be printing to, then press OK.
Hint: You can get the Port name (same as print name) from the print
server’s system information through web browser. Please refer page
44-46. Please make sure the port name is correspondence to the port
you connected.
6. Click OK to leave the LPR for TCP/IP Printing Properties
window.
- 72 -
Printing from Windows 95/98/ME
After you have added the necessary printer ports, you can add a
printer device for printing to the port. To enable printing to an lpraccessible printer port from Windows 95/98/ME:
1. From the Start menu, choose the Settings submenu, then the
Printers item within it.
folder.
Windows will display the Printers
2. Double-click on the Add Printer icon in the Printers folder.
Windows will start the Add Printer Wizard.
Click the Next > button to continue to the next screen.
3. Choose the Network Printer selection and click the Next >
button to continue.
- 73 -
4. Enter the name of the port, as displayed in the LPR for TCP/IP
Printing Port List.
Alternatively, you can click Browse... and locate the printer port.
TCP/IP printing ports are located under the Entire Network icon,
within the Print Servers - TCP/IP LPR icon.
- 74 -
Press OK when you have located the proper printer port.
Click Next > to continue to the next step.
5. At this point Windows will ask you to choose the correct printer
driver for the printer. Choose you printer’s make and model
from the list, or use the driver disk included with the printer.
When you have chosen the correct printer, click Next > to
continue.
6. Windows will then ask for a name for the new printer, and ask
whether or not you want to set the printer as the Windows
default printer. Click Finish (or Next >) to continue.
7. Windows may ask you whether or not you wish to print a test
page to make sure that the printer will work correctly. When
the test page is done printing, you will be asked whether or not
the test page printed.
- 75 -
Setting TCP/IP Printing Settings
The lpr client’s Properties dialog allows you to change several of the
client’s settings. To change these settings,
1. From the Start menu, choose the Settings submenu, then the
Control Panel item within it.
Control Panel folder.
Windows will display the
2. Double-click on the Network icon in the Control Panel folder.
3. Choose the LPR for TCP/IP Printing client and click the
Properties button.
4. Click on the Settings tab to access the lpr client settings.
Change the settings as necessary, and press OK to let the
changes take effect.
- 76 -
The parameters are as follows:
♦ Communication Timeout Determines how long, in seconds,
the system will wait before determining that it has lost
connection with lpr/lpd print servers.
♦ Retry Interval Determines how long, in seconds, the system
will wait before retrying a lost connection.
♦ Retry Times Determines how many times the system will
retry a lost connection with an lpr/lpd print server. If Infinite
is checked, it will retry indefinitely.
♦ Spool Path Gives the directory path where the system will
temporarily store lpr/lpd print server job files.
- 77 -
6
P RINTING IN W INDOWS
2000/XP
Setting Up Windows 2000 TCP/IP Printing
Following is the correct procedure for setting up TCP/IP LPR printing
under Windows 2000.
Click Start > Settings > Printers. Double Click “Add Printer”
Select “Local Printer”
- 78 -
Create a new “Standard TCP/IP Port”
Click “Next”
- 79 -
Input the IP Address of the Print Server, and the Port name (Printer
Name) of the Port that will be printed to, then click “Next”.
Hint: You can get the port Name (Same as Printer Name) from the
print server’s system information through web browser. Please refer
page 44-46. Please refer page 44-46. Please make sure the port name
is correspondence to the port you connected (etc.USB1, USB2, LPT3)
Select “Custom”, and click “Settings”.
- 80 -
Select “LPR”, and put the Port name in the field labeled “Queue
Name”. Then Click “OK”.
- 81 -
Click “Next”.
- 82 -
Click “Finish”
- 83 -
The Printer Install Wizard will now prompt for drivers. Select the
correct Make and Model, or click “Have Disk”, to provide the
Manufacturer’s Driver Disk.
Click “Next”.
- 84 -
Select a “Printer Name”.
Sharing can be enabled here.
- 85 -
Also, a Test Page can be printed to confirm proper configuration.
When the Test Page has been printed, click “Finish” to complete the
installation.
- 86 -
Setting Up Windows XP TCP/IP Printing
Following is the correct procedure for setting up TCP/IP LPR printing
under Windows XP.
Click Start > Printer and Faxes
Double Click “Add a Printer”
Click “Next”
- 87 -
Select “Local Printer”
Create a new “Standard TCP/IP Port”
- 88 -
Click “Next”
Input the IP Address of the Print Server, and the Port name of the Port
that will be printed to, then click “Next”.
Hint: You can get the Port name (same as printer name) from the print
server’s system information through web browser. Please refer page
44-46. Please make sure the port name is correspondence to the port
you connected (etc.USB1, USB2, LPT3)
- 89 -
Select “Custom”, and click “Settings”.
- 90 -
Select “LPR”, and put the Port name in the field labeled “Queue
Name”. Then Click “OK”.
Click “Next”.
- 91 -
Click “Finish”
- 92 -
The Printer Install Wizard will now prompt for drivers. Select the
correct Make and Model, or click “Have Disk”, to provide the
Manufacturer’s Driver Disk.
Click “Next”.
- 93 -
Select a “Printer Name”.
- 94 -
A Test Page can be printed to confirm proper configuration.
When the test page has been printed, click “Finish” to complete the
installation.
- 95 -
7
P RINTING IN MAC OS
Rendezvous Uses in MAC OS 10.2
The latest version of MAC OS provides a new feature that is called
Rendezvous. Rendezvous is a revolutionary networking technology
standard that lets you create an instant network of computers and
devices, which can be used throughout Mac OS 10.2 to provide
innovative ways to share files and printers and even contact other
people on the network.
For the printer connection, the Mac OS 10.2 Print Center application
uses Rendezvous to discover Rendezvous-enabled printers on the
network. When you add your computer to a network, Print Center
automatically discovers the available printers. All you have to do is
selecting the one you want to use and then start printing. You can
add a new printer to the network and all the users on the network will
see the new printer automatically appear in their Print Center, without
any configuration.
The following instructions provide a common procedure of installing
the printer:
- 96 -
1. Launch Print Center.
Add button.
Press and hold the Option key, click the
2. Select Rendezvous from the pop-up menu.
3. When clicking the Rendezvous item, the following window
appears to display the connected Rendezvous-enabled printers.
Connected printer(s)
- 97 -
4. Select the desired printer, and the following pop-up menu displays
the printer’s manufacturer. Select Generic.
5. The printer is installed into the system successfully.
- 98 -
Setting Up Apple Talk/LPR Printing
For MAC OS X User
With MAC OS X, you can use AppleTalk or LPR printers to print
through the print server. Follow the instructions below for setting up
the print server:
1. After attaching the print server to your network, change the IP
Address of your Macintosh computer to access the print server’s
web configuration. The default I P Address of the print server
is 192.168.0.1. Change your IP Address to 102.168.0.x, where x
is any number between 2 and 254.
2. Open the System Preference window and click Network. In the
Network window, select the AppleTalk tab and check the Make
AppleTalk Active option.
Check this option.
- 99 -
3. To print, open a document and select File > Print from the menu.
Select this option.
4. Select Edit Printer List from the Printer dialog box.
Select this option.
5. Click Add Printer. Then, select the desired printing protocol
(AppleTalk or LPR Printers using IP).
- 100 -
- AppleTalk: After selecting AppleTalk, the Port Name of the
print server will be displayed. Select the Port to which the
post-script printer is connected. Then, select the printer
model from the dialog box. Click Add Printer to complete
the Printer Port configuration. Select the Printer Port just
configured in the Print window. Click Print to print your
document.
- LPR Printers using IP: When you select LPR Printers
using IP Protocol, type the IP Address of the print server into
the LPR Printer’s Address field of the following window.
In the Queue Name field, type in the Port Name of the postscript printer that is connected to the Print Server. Select the
printer model from the dialog box, and select the printer
model from the pull-down menu. Click Add to complete the
process. Close all Print Center windows and select the
Printer Port that was just selected. Then, click Print to print
the document.
Port Name of the connected printer.
- 101 -
For MAC OS 9 User
If you use MAC OS 9, you can use the AppleTalk network protocol
for network communications over standard Ethernet or Fast Ethernet
using the EtherTalk transport, or over a proprietary low-speed
LocalTalk transport. Your print server can be used for network
printing to PostScript printers. You can print from any MAC OS
computer connected to your Ethernet network, either directly using an
EtherTalk connection or indirectly through a LocalTalk-to-EtherTalk
router.
To set up the print server to be used for AppleTalk printing:
1. Please confirm that the AppleTalk protocol is enabled in your
Macintosh computer.
2. Change the IP Address on one of the computers within your
network to 192.168.0.x (where x is any number between 2-254).
3. Type 192.168.0.1 (the default IP Address) into the address field of
your browser.
4. Select the Network tab and scroll to the AppleTalk protocol
section.
5. If your AppleTalk network is divided into AppleTalk zones, you
have to specify which zone the Print Server should be in. You
should locate the print server in the same zone as most of the users
who will be using it. If your network is not divided into zones, it
should contain a single asterisk “*”.
- 102 -
To print from MAC OS Client Workstations:
The actual settings of selecting a PostScript printer connected to your
print server may be different from the instructions provided in this
section, depending on the devices and the software you are using.
1. To choose a printer connected to your print server as your MAC
OS workstation’s default printer, select Chooser from the Apple
menu.
2. In the left column of Chooser window, select the desired item.
Please confirm that AppleTalk is set to Active. A list of all
networked PostScript printers will be displayed within the right
column.
Select
Check this option.
3. Double-click the name of the Printer Port you wish to use.
Printer Ports shown are examples only.
- 103 -
The
4. If you have not previously set this printer as the default, your
computer will prompt you for a PostScript Printer Description file.
Choose Select PPD.
5. Select the appropriate printer description file for your printer.
Click Open. (If your printer is not listed, click Generic to use a
generic printer description.)
The selected printer will become your computer’s default printer. You
may need to choose Page Setup in any applications you have open.
- 104 -
8
P RODUCT
S PECIFICATIONS
Printer Connection
Printer Interface: Two USB ports, compliant with USB 2.0 Hi-speed
standard.
Network Connection
Network Interface: One 10/100 Fast Ethernet port (RJ-45 connector).
Network Data Transfer Rate: 100Mbps.
Network Protocol Support
Transport Protocols: TCP/IP, SMB, NetBEUI, and AppleTalk.
TCP/IP Protocols Support: BOOTP, SNMP, Telnet, FTP, LPD,
DHCP, and IPP.
- 105 -
Hardware
SDRAM: 8MB.
Flash ROM: 2MB.
Operating System Support
- Windows 95/98/ME, Windows NT, Windows 2000/XP/2003;
- NetWare 5.x (NDPS LPR remote printing);
- HP-UX Unix, Sun O.S, Solaris, SCO Unix, AIX;
- Unixware and Linux;
- Mac OS, AppleTalk.
Management
Standard: SNMP
MIBs: MIB-II (RFC 1213).
Utilities: PS-Utility, PS Wizard. PSM Setup
LEDs
Power, LAN, USB1, USB2, LPT.
- 106 -
Environmental and Physical
Power Supply: 5VDC.
Operating Temperature: 0°C to 50°C.
Storage Temperature: -25°C to 55°C.
Humidity: 5% to 95%, non-condensing at 30°C.
EMI Compliance
FCC Class B, CE Class B
- 107 -
Limited Warranty
TRENDnet its products against defects in material and workmanship, under
normal use and service, for the following lengths of time from the date of
purchase.
TE100-P21 Print Server – 5 Years Warranty
If a product does not operate as warranted above during the applicable
warranty period, TRENDnet shall, at its option and expense, repair the
defective product or part, deliver to customer an equivalent product or part to
replace the defective item, or refund to customer the purchase price paid for
the defective product. All products that are replaced will become the property
of TRENDnet. Replacement products may be new or reconditioned.
TRENDnet shall not be responsible for any software, firmware, information, or
memory data of customer contained in, stored on, or integrated with any
products returned to TRENDnet pursuant to any warranty.
There are no user serviceable parts inside the product. Do not remove or
attempt to service the product by any unauthorized service center. This
warranty is voided if (i) the product has been modified or repaired by any
unauthorized service center, (ii) the product was subject to accident, abuse, or
improper use (iii) the product was subject to conditions more severe than
those specified in the manual.
Warranty service may be obtained by contacting TRENDnet office within the
applicable warranty period for a Return Material Authorization (RMA) number,
accompanied by a copy of the dated proof of the purchase. Products
returned to TRENDnet must be pre-authorized by TRENDnet with RMA
number marked on the outside of the package, and sent prepaid, insured and
packaged appropriately for safe shipment.
WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT
OPERATE AS WARRANTED ABOVE, THE CUSTOMER’S SOLE REMEDY
SHALL BE, AT TRENDNET’S OPTION, REPAIR OR REPLACEMENT. THE
FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE
IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,
EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR
OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. TRENDNET NEITHER
ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT
ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION
MAINTENANCE OR USE OF TRENDNET’S PRODUCTS.
TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS
TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT
IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S
OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER
INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR
OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE
INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER
HAZARD.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW
TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY
LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT,
SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF
REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION
OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE,
PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF
SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR,
REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT
TRENDNET’S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES
WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL
FAIL OF ITS ESSENTIAL PURPOSE.
Governing Law: This Limited Warranty shall be governed by the laws of the
state of California.
AC/DC Power Adapter, Cooling Fan, and Power Supply carry - 1 Year
Warranty
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement