TRENDnet TFM-PCIV92A User's Manual

TRENDnet TFM-PCIV92A User's Manual
TABLE OF CONTENT
1. Contents of Package
2. Comprehensive Modem Installation Instructions
1
1
2.1
2.2
Modem Installation
Hardware Installation
1
2.3
System Setup
3
2.3.1
Setup Instructions for Windows 98
3
2.3.2
Uninstall Modem from Windows 98
4
2.3.3
Setup Instructions for Windows Me
5
2.3.4
Uninstall Modem from Windows Me
6
2.3.5
Setup Instructions for Windows 2000
7
2.3.6
Uninstall Modem from Windows 2000
2.3.7
Setup Instructions for Windows XP
10
2.3.8
Uninstall Modem from Windows XP
12
2.4
Testing your modem
13
2.5
Install Communication Software
13
3. Troubleshooting
Appendix 1:
Appendix 2:
Appendix 3:
Appendix 4:
Appendix 5:
1
9
14
Modem Specifications..…..............….......16
AT Command Set ………...............……....17
S-Register Summary ……..............….......22
Result Codes Summary..…..............….....25
Government Compliance...............……....27
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
Section 1
7.
Fasten the modem bracket firmly with the screw saved in step 5.
8.
Reassemble your computer cover and re-plug cables for peripheral.
9.
Plug one end of telephone cord into the "LINE" jack at the modem's bracket. Plug another end of the
Contents of Package
z
One V.92/V.90 PCI bus window modem
z
One telephone cable
z
One CD-ROM disk comprises Communication software, Modem Driver & User's Manual
z
Quick installation guide
telephone cord into the telephone wall jack
10. Some models may comprise a phone jack for an optional telephone. If you wish to use a phone through
the same telephone wall jack when the modem is not in use, plug the telephone cord of the phone into
"PHONE" jack at the modem's bracket now. Lift the handset and listen for a dial tone to check for a
properly connection.
Please contact the place of purchase if any of the above listed items are missing.
11.
Plug the power cord into the computer and turn the computer on.
12. Up to now, the hardware installation has been finished. If you have not encountered any problems, you
Section 2
Comprehensive Modem Installation Instructions
Section 2.1
Modem Installation
can go to Section 2.3 System Setup. If you are having problems, see Section 3 Troubleshooting.
NOTE : The telephone wall jack you use must be for an ANALOG phone line (the type found in most homes).
Many offices are equipped with digital phone lines. Please be sure you know which type of line you have. The
This section will provide instructions for the installation of your modem. There are hardware installation and
modem will be damaged if you use a digital phone line.
system setup two parts for the modem. The modem hardware must be installed into the computer correctly
before you start the system setup.
Section 2.2
Hardware Installation
Please refer to Fig. 2 - 1 and proceed to following steps for how to insert your modem into the computer and
connect telephone wire and audio accessories.
Figure 2-1 Internal modem figure
1.
Turn off and unplug your computer from the AC outlet.
2.
Unplug any peripheral devices (keyboard, monitor, etc.) from your computer to avoid the
risk of electric shock.
3.
Take the cover off your computer, review computer's manual if you need further instructions.
4.
Find an empty PCI slot.
5.
Unscrew the PCI slot bracket and save the screw, then remove the bracket.
6.
Plug the modem into the PCI slot carefully until the modem is properly seated.
-1-
Rev.1.00.2.1.34
-2-
Rev.1.00.2.1.34
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
Section 2.3.2
Section 2.3
System Setup
Section 2.3.1
Setup instructions for Windows 98
STEP 1.
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
STEP 1.
Uninstall Modem from Windows 98
Open Control Panel window, then click Add/Remove Programs icon.
After you complete the modem hardware installation and turn on your PC, Windows system will
automatically detect your new added devices. Windows system will prompt you with an Add New
Hardware Wizard.
STEP 2.
Then click on Cancel.
Choose Agere Systems PCI Soft Modem device in stall/Uninstall tab, then click on
Add/Remove… .
STEP 2.
Insert the Modem Driver CD-ROM disk attached with your modem into the CD-ROM drive device,
Then run <CD-ROM letter>:\drivers\Win98\Setup.exe as shown in figure.
Then click on OK
STEP 3.
And then, a prompt screen will ask you to ensure to install the modem driver.
Then click OK.
STEP 3.
Click Yes to ensure to remove Agere Systems PCI Soft Modem device and its drivers.
STEP 4.
Click Yes to restart your computer for all of the changes to take effect.
The setup utility will copy the needed files into windows system.
STEP 4.
If there is no error message while the system is installing, your modem has been set up properly
and functionally.
-3-
Rev.1.00.2.1.34
-4-
Rev.1.00.2.1.34
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
Section 2.3.3
STEP 1.
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
Section 2.3.4
Setup instructions for Windows Me
After you complete the modem hardware installation and turn on your PC, Windows system will
STEP 1.
Uninstall Modem from Windows Me
Open Control Panel window, then click on Add/Remove Programs icon.
automatically detect and install your new added devices. Windows system will prompt you with an
Add New Hardware Wizard.
Click on Cancel.
STEP 2.
STEP 2.
Choose Agere Systems PCI Soft Modem device in Install/Uninstall tab, then click on
Add/Remove...
Insert the Modem Driver CD-ROM disk attached with your modem into the CD-ROM drive device,
then run <CD-ROM letter>:\drivers\WinMe\SETUP.EXE to upgrade the modem driver as shown
in figure.
Then click on OK.
STEP 3.
And then, a prompt screen will ask you to ensure to install the modem driver.
Then click OK.
STEP 3.
Click Yes to ensure to remove Agere Systems PCI Soft Modem device and its drivers.
STEP 4.
Click Yes to restart your computer for all of the changes to take effect.
The setup utility will copy the needed files into windows system.
STEP 4.
If there is no error message while the system is installing, your modem has been set up properly
and functionally.
-5-
Rev.1.00.2.1.34
-6-
Rev.1.00.2.1.34
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
Section 2.3.5
STEP 4.
Setup instructions for Windows 2000
The prompt screens will be warning you that the digital signature of programs have not found as
shown in figure.
STEP 1.
After you complete the modem hardware installation and turn on your PC, Windows system will
automatically detect your new added devices. Windows system will prompt you with an Add New
Hardware Wizard.
Please always click on Yes.
STEP 5.
If there is no error message while the system is installing, your modem has been set up properly
and functionally.
Click on Cancel.
STEP 2.
Insert the Modem Driver CD-ROM disk attached with your modem into the CD-ROM drive device,
then run <CD-ROM letter>:\drivers\Win2K&XP\Setup.exe as shown in figure.
Then click on OK.
STEP 3.
And then, a prompt screen will ask you to ensure to install the modem driver.
Then click on OK.
The setup utility will copy the needed files into windows system.
-7-
Rev.1.00.2.1.34
-8-
Rev.1.00.2.1.34
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
Section 2.3.6
STEP 1.
Uninstall Modem from Windows 2000
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
Section 2.3.7
Open Control Panel window and choose Add/Remove Programs icon.
STEP 1.
Setup instructions for Windows XP
After you complete the modem hardware installation and turn on your PC, Windows system will
automatically detect and install your new added devices. Windows system will prompt you with an
Add New Hardware Wizard.
Click on Cancel.
STEP 2.
Select Agere Systems PCI Soft Modem device in Change or Remove Programs tab, then click
on Change/Remove.
STEP 2.
Insert the Modem Driver CD-ROM disk attached with your modem into the CD-ROM drive device,
Then run <CD-ROM letter>:\Drivers\Win2K&XP\SETUP.EXE to upgrade the modem driver as
shown in figure.
Then click on OK.
STEP 3.
Click Yes to ensure to remove Agere Systems PCI Soft Modem device and its drivers.
STEP 3.
STEP 4.
Click Yes to restart your computer for all of the changes to take effect.
And then, a prompt screen will ask you to ensure to install the modem driver.
Then click OK.
The setup utility will copy the needed files into windows system.
-9-
Rev.1.00.2.1.34
- 10 -
Rev.1.00.2.1.34
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
STEP 4.
Section 2.3.8
The prompt screens will be warning you that the digital signature of programs have not found as
Uninstall Modem from Windows XP
shown in figure.
STEP 1.
Open Control Panel window, then click on Add or Remove Programs icon.
Please always click on Yes.
STEP 5.
If there is no error message while the system is installing, your modem has been set up properly
STEP 2.
and functionally.
Choose Agere Systems PCI Soft Modem device in Change or Remove Programs tab, then
click on Change/Remove.
- 11 -
Rev.1.00.2.1.34
STEP 3.
Click Yes to ensure to remove Agere Systems PCI Soft Modem device and its drivers.
STEP 4.
Click Yes to restart your computer for all of the changes to take effect.
- 12 -
Rev.1.00.2.1.34
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
Section 3
Section 2.4
Troubleshooting
Testing Your Modem
Your modem is designed to provide reliable and trouble-free functionality, however, should you experience
Before you set up your software, start with a quick test to check that your modem is working. Once you have
any difficulty, the information contained in this section will assist you in determining and resolving the source
determined that your modem is setup properly, go on to Section 2.5 Install Communication Software to
of the problem.
install your communications software. If you are having problems, see Section 3 Troubleshooting.
Problem: Modem does not respond to AT commands
Click on Start and point to Setting. Then click on Control Panel. When the Control Panel window opens.
Possible solutions:
Scroll down to the Modem icon and double click on it. Click on the Diagnostics tab and highlight the COM
1.
Make sure the modem is not configured with a conflicting COM port and IRQ setting. Make sure the
port for your modem. Then click on More Info, your computer will automatically communicate with your new
communication software is configured with the correct COM and IRQ settings (the same COM port and
modem using AT commands and receiving responses from your modem. A list of response means the modem
IRQ as the modem). Your communications software will not be able to send or receive any data if it is
is setup properly.
not configured to match the COM port and IRQ settings for the modem.
Section 2.5
Install Communication Software
DOS based communication program is not working with this modem neither can you operate the modem
in MS-DOS prompt screen.
You can install the communication software from the CD-ROM disc attached with your new modem. Please
consult the software manual in the CD-ROM disc for the detail of software installation.
2.
Make sure the modem is properly initialized using the driver software. The software may improperly
Initialize your modem because you have selected an incorrect modem type. You may also be prompted
to enter an initialization string by the software. Use AT&F as your initialization string.
You do not have to use the communication software attached with your new modem. The modem was
designed for and tested using a wide range of communications software packages. Many communication
applications identify the modem automatically and configure themselves for the correct operating settings.
Problem: Modem dials but does not connect
Some of the communication applications will ask you to select the type of modem you are using. Select a
Possible solutions:
Generic Fax class 1 modem will let you use basic communication and fax functions.
1.
Be sure the IRQ setting is identical on the modem and the software.
2.
Make sure that the phone line is working properly. A noisy line will prevent proper modem operation.
Problem: Modem makes a connection but no data appears on screen
Possible solutions:
1.
Make sure all communication parameters (baud rate, data, stop, and parity bits) are properly configured
and are identical on both sides. Be certain hardware flow control (RTS/CTS - default) is enabled in both
the modem and the communication software.
2.
Press the ENTER key several times. The remote system may be waiting to receive your data before it
begins.
3.
Make sure the correct terminal emulation mode is being used in the software (refer to software manual).
Problem: Modem displays errors while on-line with a remote modem
Possible solutions:
1.
Make sure Call Waiting is turned off.
2.
Make sure RTS/CTS hardware flow control is enabled (do not use XON/XOFF software flow control
when transferring binary files).
- 13 -
Rev.1.00.2.1.34
- 14 -
Rev.1.00.2.1.34
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
3.
Appendix 1
Make sure the data speed is not faster than your computer capability. Operating too many applications
Modem Specifications
at the same time may cause communication problem. Close unnecessary application in your system.
Modulation standards : V.92, V.90, V.34, V.32bis, V.32, V.29, V.27ter, V.22bis, V.23,V.22, V.21,V.17,
Bell212/103
Problem: Modem exhibits poor voice recording or playback
Possible solutions:
Compression
: V.44, V.42bis, MNP Class 5
1.
Make sure the correct modem type is selected in the Voice/FAX software. Volume adjustment is
Error Correction
: V.42, MNP Class 2-4
available in control panel.
Host Interface
: PCI bus
Make sure your computer is fast enough to handle voice operations (38.4 Kbps). Voice operations are
FAX Group
: Group III
CPU intensive and require a better CPU sharing when running under Windows.
FAX Command
: EIA/TIA 578 class 1
2.
Problem: No dial tone
Possible solutions:
1.
Ensure that the telephone cord it securely connected at both modem and wall outlet.
2.
Unplug the telephone cord from the computer and connect it directly to a telephone from the wall outlet.
Check for a dial tone. If there is none, the problem is in the telephone cord or system. Call your
telephone service provider.
3.
Double-check your country setting. Different country setting will cause different modem performance.
Please select the correct country as you located.
4.
Check modem performance with a direct line from your telephone company. Some PBXs may cause the
telephone line condition change and affect modem performance.
Problem: The modem does not answer incoming calls
Possible solutions:
1.
Ensure that the automatic answer parameter is set to one of the enabled options, using the ATS0
command (ATS0=1 to answer after one ring, and so on).
2.
Ensure that no other devices, such as fax or answering machines, are answering calls before the
modem does.
If you cannot resolve your situation after reading this section, contact your dealer or vendor for assistance.
- 15 -
Rev.1.00.2.1.34
- 16 -
Rev.1.00.2.1.34
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
Appendix 2
AT command set
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
AT
Command prefix
Executing commands
,
Your modem is in Command Mode upon power-on and is ready to receive and execute AT commands. The
!
Flash hook
modem remains in Command Mode until it makes a connection with a remote modem. Commands may be
@
Wait for quiet answer
sent to the modem from an attached terminal or a PC running a communication program. This modem is
^
Disable data calling tone transmission
designed to operate at common DTE speeds ranging from 115.2 Kbps to 300 bps. All commands and data
$
Bong tone detection
must be issued to the modem using one of the valid DTE speeds.
;
Return to command mode
E0
Disables echo
Pause the time specified in S-register S8
AT commands and format
E1
Enables echo
All commands must begin with the AT prefix, followed by the command letter and ended with the ENTER key.
H0
Hang up the telephone line
All default settings are printed in bold text. Spaces are allowed in the command string to increase command
H1
Pick up the telephone line
line readability but are ignored by the modem during command execution. All commands may be typed in
I0
Reports modem identify string and driver version number
either upper or lower case, but not mixed. A command issued without any parameters is considered as
I1
Calculate ROM checksum and report it to DTE
specifying the same command with a parameter of "0".
I2
Verifies ROM checksum and report OK or ERROR
Example: ATL [ENTER]
I3
Report modem identify string and driver version number
This command causes your modem to lower its speaker volume.
I4
Report firmware version for datapump
I5
Report the board/firmware ID, country ID and subsystem vendor ID
AT Command Summary
AT
Command prefix
I9
Report country ID
I11
Report connection information
L0
Low speaker volume
A/
Repeat last command
L1
Low speaker volume
A
Answer
L2
Medium speaker volume
B0
Select V.22/V.21
L3
High speaker volume
B1
Select B212A/B103
M0
Speaker always off
B15
Select V.21 when the modem is at 300 BPS
M1
Speaker on until carrier present
B16
Select Bell 103J when the modem is at 300 BPS
M2
Speaker always on
D
Dial
M3
Speaker off during dialing; speaker on until carrier present
N0
Handshake only at the communication standard specified by S37 and
ATB command
0-9
Dialing digits
ABCD*#
Tone dial characters
L
Redial last number
O0
Return to data mode
P
Pulse dial
O1
Retrain and return to data mode
T
Tone dial
O3
Rate re-negotiation and return to data mode
V
The modem switches to speakerphone mode and dials the number
P
Select pulse dialing
R
The modem goes into answer mode directly after finish dialing
Q0
Enables result code
S=n
Dial stored telephone number n
Q1
Disables result code
W
Wait for dial tone
Sn
Select S-register n; refer to S-register summary for the details
N1
Begin the handshake at the communication standard specified by s37 and ATB,
and fallback to lower speed may occur
- 17 -
Rev.1.00.2.1.34
- 18 -
Rev.1.00.2.1.34
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
AT
Command prefix
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
AT
Command prefix
Sn=x
Write x to S-register n; refer to S-register summary for the details
&Q6
Sn?
Read from S-register n; refer to S-register summary for the details
&Q8
Same as &Q0
T
Select tone dialing
V0
Choose numeric form result code
V1
Choose verbose form result code
W0
Reports DTE connect speed result code, disable protocol result codes
&S0
DSR always ON
W1
Reports DTE connect speed result code, enable protocol result codes
&S1
DSR ON only during handshaking and when carrier is lost
W2
Reports DCE connect speed result code, enable protocol result codes
&T0
Terminates test in progress
X0
Enables result code 0-4; disables dial tone and busy tone detection
&T1
Initiates local analog loopback(LAL)
X1
Enables result code 0-5,10 and above; disables dial tone and busy tone detection
&T3
Initiates local digital loopback
Select MNP error control mode. If fail to connect, the modem will fallback according to
current setting in S36
&Q9
Select V42 or MNP error control mode. If fails to establish, the modem will fallback
according to current setting in S36
Enables result code 0-6, 10 and above; enables dial tone detection and disables busy
&T6
Initiates remote digital loopback(RDL)
tone detection
&V
View active profile, stored user profile and stored telephone number
Enables result code 0-5,7,10 and above; disables dial tone detection and enables busy
&W
Stores active profile into user profile
tone detection
&Zn=x
Stores telephone number x(up to 40 digits) to location n(0-3).I301 V.90
X4
Enables result code 0-7, 10 and above; enables dial tone and busy tone detection
%B
View number in blacklist
Z
Reset modem and recalls user profile
%C0
Disables data compression
&C0
Ignores carrier status; CD always ON
%C1
Enables data compression
&C1
CD set according to carrier status
%E0
Disables fallback and fall forward
&D0
Ignores DTR
%E1
Enables fallback, disables fall forward
X2
X3
&D1
&D2
Modem switches from data mode to command mode when an ON-to-OFF transition of
%E2
Enables fallback and fall forward
DTR occurs
-C0
Disables calling tone
When DTR switches OFF , the modem goes on-hook and disables
-C1
Enables 1300 Hz calling tone
auto-answer
-V90=n
Control V.90 downstream speed
&D3
Reset modem and recall user profile when DTR switches OFF
n=0
V.90 disabled
&F
Load factory defaults
n=1
Auto rate
&G0
Disables guard tone
n=2
28000 BPS
&G1
Enables 550 Hz guard tone
n=3
29333 BPS
&G2
Enables 1800 Hz guard tone
n=4
30666 BPS
&K0
Disables flow control
n=5
32000 BPS
&K3
Enables CTS/RTS hardware flow control
n=6
33333 BPS
&K4
Enables XON/XOFF software flow control
n=7
34666 BPS
&M0
Select asyncronous buffer mode
n=8
36000 BPS
&P0
Select 10 pps pulse dial with 39%/61% make/break ratio
n=9
37333 BPS
&P1
Select 10 pps pulse dial with 33%/67% make/break ratio
n = 10
38666 BPS
&P2
Select 20 pps pulse dial with 33%/67% make/break ratio
n = 11
40000 BPS
&Q0
Select asynchronous buffer mode
n = 12
41333 BPS
&Q5
Select Error control mode
n = 13
42666 BPS
- 19 -
Rev.1.00.2.1.34
- 20 -
Rev.1.00.2.1.34
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
Appendix 3
AT
S-Register Summary
Command prefix
n = 14
44000 BPS
Register
Function
Default Range
Units
n = 15
45333 BPS
S0*
No. of rings to start auto-answer 0
0-255
n = 16
46666 BPS
S1*
Ring count
0
0-255
ring
n = 17
48000 BPS
S2*
Escape character
43
0-255
ASCII
n = 18
49333 BPS
S3
Carriage return character
13
0-127
ASCII
n = 19
50666 BPS
S4
Line feed character
10
0-127
ASCII
n = 20
52000 BPS
S5
Backspace character
8
0-32,127
ASCII
n = 21
53333 BPS
ring
S6*
Wait before dialing
2
2-65
second
-V90?
Reports current V.90 setting
S7*
Wait for carrier
50
1-255
second
\A0
Set maximum MNP block size to 64 characters
S8*
Pause time for dial modifier ,
2
0-65
second
\A1
Set maximum MNP block size to 128 characters
S10*
Lost carrier hang up delay
20
1-254
0.1second
\A2
Set maximum MNP block size to 192 characters
S11*
DTMF dialing speed
95
50-150
msec
\A3
Set maximum MNP block size to 256 characters
S12*
Escape guard time
50
0-255
20 msec
\Bn
Transmit break in n*100ms (n = 0-9)
S14*
Bit-mapped register
-
0-255
-
\G0
Disables XON/XOFF flow control between local and remote modems
Bit 0,1,2
\G1
Enables XON/XOFF flow control between local and remote modems
Bit 3
\J0
Disables DTE speed adjust
\J1
Enables DTE speed adjust
Bit 4,5
\Kn
Set break control (n=0-5, default is 5).
Bit 6
\N0
Select normal mode
\N1
Select normal mode
\N2
Select MNP reliable mode
\N3
Select V.42 auto-reliable mode
Bit0,1,2
\N4
Select V.42 reliable mode
Bit 4-3
=
00
&D0 is selected
\Q0
Disables flow control
=
01
&D1 is selected
\Q1
Enables XON/XOFF software flow control
=
10
&D2 is selected
\Q2
Enables CTS hardware flow control
=
11
&D3 is selected
=
0
&C0 is selected
=
1
&C1 is selected
=
0
V0 is selected
=
1
V1 is selected
=
0
10 PPS pulse dialing(&P0, &P1)
=
1
20 PPS pulse dialing(&P2)
Reserved
Bit 7
S21*
Reserved
Bit-mapped register
Bit 5
\Q3
Enables CTS/RTS hardware flow control
\Tn
Set inactivity timer in minutes(n=0-255, default is 0)
\V0
Disables protocol result code appended to DCE speed
\V1
Enables protocol result code appended to DCE speed
\X0
Process XON/XOFF character as flow control character only
Bit 0,1,2,3
Process XON/XOFF character as flow control character and pass through to local DTE
Bit 6-4
\X1
Reserved
Bit 6,7
S22*
-
-
000 X0 is selected
001 Reserved
Notes:
=
010 Reserved
The default setting of commands is in bold Italic text format.
=
011 Reserved
=
100 X1 is selected
Rev.1.00.2.1.34
0-255
-
Reserved
=
- 21 -
-
Reserved
Bit-mapped register
=
or remote modem
0-255
Reserved
- 22 -
Rev.1.00.2.1.34
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
Register
Function
Bit 7
S28*
Default Range
Units
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
Register
Function
=
101 X2 is selected
=
1
Auto rate
=
110 X3 is selected
=
2
32K BPS
=
111 X4 is selected
=
3
34K BPS
=
0
33/67 M/B ratio is selected(&P1, &P2)
=
4
36K BPS
=
1
39/61 M/B ratio is selected(&P0)
=
5
38K BPS
=
6
40K BPS
Control V.34 modulation
1
0-1
-
=
0
Disables V.34 modulation
=
7
42K BPS
=
1
Enables V.34 modulation
=
8
44K BPS
S30*
Inactivity timer
0
0-255
minute
=
9
46K BPS
S32*
Synthetic ring volume
10
0-255
-
=
10
48K BPS
S33*
Synthetic ring frequency
0
0-5
-
=
11
50K BPS
S35*
Data calling tone
0
0-1
=
12
52K BPS
S37*
S38*
=
0
Disables data calling
=
13
54K BPS
=
1
Enables data calling
=
14
56K BPS
Maximum line speed attempted 0
0-19
S48*
-
Error control feature
Default Range
Units
7
7,128
-
=
0
Auto rate
=
7
=
1
Reserved
=
128 Negotiation disabled
Negotiation enabled
=
2
1200/75 bps
S89*
Sleep mode timer
10
0,5-65
second
=
3
300 BPS
S108 *
Network codec type
7
7,22,33
-
=
4
Reserved
=
7
Specified by central site mode
=
5
1200 BPS
=
22
u-law
=
6
2400 BPS
=
33
A-law
=
7
4800 BPS
=
8
7200 BPS
=
9
9600 BPS
=
10
12000 BPS
=
11
14400 BPS
=
12
16800 BPS
=
13
19200 BPS
=
14
21600 BPS
=
15
24000 BPS
=
16
26400 BPS
=
17
28800 BPS
=
18
=
19
31200 BPS
33600 BPS
K56flex downstream rate
=
0
Notes : The value of the S-registers marked with (*) were saved in NVRAM
1
0-14
-
Disables K56flex
- 23 -
Rev.1.00.2.1.34
- 24 -
Rev.1.00.2.1.34
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
Appendix 4
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
Result Codes Summary
Verbose Code
Verbose Code
Numeric Code
Numeric Code
CONNECT 38000 EC*
73
OK
0
CONNECT 38400 EC*
28
CONNECT
1
CONNECT 38666 EC*
106
RING
2
CONNECT 40000 EC*
74
NO CARRIER
3
CONNECT 41333 EC*
107
ERROR
4
CONNECT 42000 EC*
75
CONNECT 1200 EC*
5
CONNECT 42666 EC*
108
NO DIAL TONE
6
CONNECT 44000 EC*
76
BUSY
7
CONNECT 45333 EC*
109
NO ANSWER
8
CONNECT 46000 EC*
77
DELAYED
88
CONNECT 46666 EC*
110
BLACKLISTED
89
CONNECT 48000 EC*
78
BLACKLIST FULL
90
CONNECT 49333 EC*
111
CONNECT 300 EC*
40
CONNECT 50000 EC*
79
CONNECT 2400 EC*
10
CONNECT 50666 EC*
112
CONNECT 4800 EC*
11
CONNECT 52000 EC*
80
CONNECT 7200 EC*
24
CONNECT 53333 EC*
113
CONNECT 9600 EC*
12
CONNECT 54000 EC*
81
CONNECT 12000 EC*
25
CONNECT 54666 EC*
114
CONNECT 14400 EC*
13
CONNECT 56000 EC*
82
CONNECT 16800 EC*
86
CONNECT 57600 EC*
18
CONNECT 19200 EC*
14
CONNECT 115200 EC*
87
CONNECT 21600 EC*
55
CONNECT 24000 EC*
56
* EC only appear when the extended result codes configuration option is enabled. EC is
CONNECT 26400 EC*
57
replaced by one of the following symbols, depending upon the error control method used:
CONNECT 28000 EC*
100
V.42bis
- V.42 error control and V.42bis data compression.
CONNECT 28800 EC*
58
V.42
- V.42 error control only.
CONNECT 29333 EC*
101
MNP5
- MNP class 4 error control and MNP class 5 data compression.
CONNECT 30666 EC*
102
MNP4
- MNP class 4 error control only.
CONNECT 31200 EC*
59
NoEC
- No error control protocol.
CONNECT 32000 EC*
70
CONNECT 33333 EC*
103
CONNECT 33600 EC*
60
CONNECT 34000 EC*
71
CONNECT 34666 EC*
104
CONNECT 36000 EC*
72
CONNECT 37333 EC*
105
Note:
- 25 -
Rev.1.00.2.1.34
- 26 -
Rev.1.00.2.1.34
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
TFM-PCIV92A User’s Guide
_________________________________________________________________________________________________________________________
Appendix 5 Government compliance notices
DOC compliance information
FCC compliance
NOTICE: The Canadian Department of Communications label identifies certified equipment. This certification
This equipment complies with Part 68 of the FCC Rules. On this equipment is a label that contains, among
means that the equipment meets certain telecommunications network protective, operational and safety
other information, the FCC registration number and Ringer Equivalence Number (REN) for this equipment.
requirements. The Department does not guarantee the equipment will operate to the user’s satisfaction.
You must, upon request, provide this information to your telephone company.
Before installing this equipment, users ensure that it is permissible to be connected to the facilities of the local
Telecommunications Company. The equipment must also be installed using an acceptable method of
If your telephone equipment causes harm to the telephone network, the Telephone Company may discontinue
connection. The customer should be aware that compliance with the above conditions might not prevent
your service temporarily. If possible, they will notify in advance. But, if advance notice isn’t practical, you will
degradation of service in some situations.
be notified as soon as possible. You will be informed of your right to file a complaint with the FCC.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by
Your telephone company may make changes in its facilities, equipment, operations, or procedures that could
the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may
affect proper operation of your equipment. If they do, you will be notified in advance to give you an opportunity
give the telecommunications company cause to request the user to disconnect the equipment.
to maintain uninterrupted telephone service.
The FCC prohibits this equipment to be connected to party lines or coin-telephone service.
Users should ensure for their own protection that the electrical ground connections of the power utility,
In the event that this equipment should fail to operate properly, disconnect the equipment from the phone line
telephone lines and internal metallic water pipe system, if present, are connected together. This precaution
to determine if it is causing the problem. If the problem is with the equipment, discontinue use and contact
may be particularly important in rural areas.
your dealer or vendor.
CAUTION: Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate.
NOTICE: The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to
FCC Class B statement
be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
loop may consist of any combination of devices subject only to the requirement that the sum of the Load
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
Numbers of all the devices does not exceed 100.
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause harmful interference to
European CTR 21 compliance
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
The equipment has been approved in accordance with Council Decision 98/482/EC for pan-European single
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
terminal connection to the public switched telephone network (PSTN). However, due to differences between
one or more of the following measures:
the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional
Reorient or relocate the receiving antenna.
assurance of successful operation on every PSTN network termination point. In the event of problem, you
Increase the separation between the equipment and the receiver.
should contact your equipment supplier in the first instance.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Note: The manufacturer should ensure that the vendor and user of the equipment is clearly informed of the
Consult the dealer or an experienced radio/TV technician for help.
above information by means of package and /or user manuals of the forms of user instructions.
Notice: 1) Shielded cables, if any, must be used in order to comply with the emission limits.
2) Any change or modification not expressly approved by the Grantee of the equipment
authorization could void the userٛ s authority to operate the equipment.
- 27 -
Rev.1.00.2.1.34
- 28 -
Rev.1.00.2.1.34
Limited Warranty
TRENDware warrants its products against defects in material and workmanship, under
normal use and service, for the following lengths of time from the date of purchase.
TFM-PCIV92A – 3 Years Warranty
If a product does not operate as warranted above during the applicable warranty period,
TRENDware shall, at its option and expense, repair the defective product or part, deliver to
customer an equivalent product or part to replace the defective item, or refund to customer
the purchase price paid for the defective product. All products that are replaced will
become the property of TRENDware. Replacement products may be new or
reconditioned.
TRENDware shall not be responsible for any software, firmware, information, or memory
data of customer contained in, stored on, or integrated with any products returned to
TRENDware pursuant to any warranty.
There are no user serviceable parts inside the product. Do not remove or attempt to
service the product by any unauthorized service center. This warranty is voided if (i) the
product has been modified or repaired by any unauthorized service center, (ii) the product
was subject to accident, abuse, or improper use (iii) the product was subject to conditions
more severe than those specified in the manual.
Warranty service may be obtained by contacting TRENDware office within the applicable
warranty period for a Return Material Authorization (RMA) number, accompanied by a copy
of the dated proof of the purchase. Products returned to TRENDware must be
pre-authorized by TRENDware with RMA number marked on the outside of the package,
and sent prepaid, insured and packaged appropriately for safe shipment.
WARRANTIES EXCLUSIVE: IF THE TRENDWARE PRODUCT DOES NOT OPERATE AS
WARRANTED ABOVE, THE CUSTOMER’S SOLE REMEDY SHALL BE, AT
TRENDWARE’S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING
WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF
LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TRENDWARE
NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT
ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION
MAINTENANCE OR USE OF TRENDWARE’S PRODUCTS.
TRENDWARE SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND
EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES
NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE,
NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO
REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE
INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDWARE
ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER
BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL,
CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR
FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF
INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE,
PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH
DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF
THE PURCHASE PRICE PAID, AT TRENDWARE’S OPTION. THIS DISCLAIMER OF
LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED
HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.
Governing Law: This Limited Warranty shall be governed by the laws of the state of
California.
Technical Support
You can find the most recent driver/firmware/software and user documentations on the
TRENDware website. TRENDware provides FREE technical support for all
customers for the duration of the warranty period on this product.
TRENDware Technical Support
Tel: +1-310-891-1100
Fax: +1-310-8911111
E-mail: [email protected]
www.TRENDnet.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement