l 1 Assembly Instructions
ITEM NO.: 31126
Ú Fixture loop(1)
РЕ Nipple(2)
am -—- — Socket ring(3)
\ /— Glass shade(4)
ОК Socket(5)
Ball screw(9) — tn
Arm(8) \ // 7
Arm(7) —— = tim =
Housing(6)
НЕСЕТ ТТ
TED
a ll
Inn
1.Carefully remove the fixture out of the carton,and check that all parts are included referring to the above
illustration. Make sure not to misplace any parts that are needed for the installation;
2.Screw the Fixture loop(1) onto the Nipple(2); |
3.Adjust the arms its desired position,insert the bottom end of Arm (7) into Housing (6) ,attach the top end of
Arm(7) onto Arm(8) with Ball screw(9);
4 Put Glass shade (4) over Socket (5) ,then secure with Socket ring (3);
5.Install the lamps on.
Assembly Instruction for the
fixture with safety cable
NOTE: Fixtures weighing over 50 lbs, must be
supported independently of the outlet box
1)Turn off power
2)Supply wires shall enter the outlet box through any knockout except the
top center knockout, — ОД Support Cable
3)Fixture is to be mounted by a steel pipe approximately 3/470f Structural Bridging |
3/8-18NPSN threads at bottom. (Not Supplied) Position pipe so that Member
approximately 1/2"of thread protrudes into outlet box. Attach pipe to a
structural bridging member of sufficient strength to support at least 4 times
the fixture weigh. Clamps
4)Thread pipe coupling onto protruding inside outlet box, Steel Pipe
5)Thread hex nut onto threaded pipe. Screw threaded pipe into pipe A0
coupling. Secure in place by tightening hex nut against pipe coupling and
tightening allen head screw. Outlet Box
§)Thread hex nut. Ship on ground wire and thread a second hex nut onto ~~
threaded pipe.
7)Connect screw collar loop (without threaded ring) to threaded pipe.
R)Pass canopy over screw collar loop. Approximately one-half of the
screw collar loop exterior thread should be exposed. Adjust loop as
required. Remove canopy and tighten hex nut against screw collar loop. ‚
Tighten second hex nut against first to hold ground wire in place. _.— Pipe Coupling
MAttach chain to fixture (not shown) | |
10)Slip threaded ring then canopy onto chain
1 Attach chain (with fixture connected) to bottom of screw collar loop. Allen Head Screw
12)Weave silver support cable up chain and exit through top hole inside
of pipe coupling. Slip cable through top existing opening or drill 3/16" día. Hexnut
Ground Wire
Hole near center of outlet box. Wrap cable around structural member
described in step #3. Cable must be pulled tight to evenly distribute
fixture weight between cable and chain. Secure cable with (2) claps pa
provided. Threaded Pipe
t3)Weavc both fixture wires and copper ground wire up chain and exit
through top hole inside of pipe coupling.
14)Connect fixture ground wire and ground wire attached to threaded pipe Open Loop
to outlet box ground wire with wire connector (not provided). Never — Screw Collar Loop yd
connect ground wire to black or power supply wires. “Canopy
Make wire connections {connectors not provided) Reference chart below и
for correct connections and wire accordingly.
Connect Black or Connect Black or
Red Supply Wire to: White Supply Wire io:
Black White
*Paralle] cord (round & smooth) — |*Parallel cord (square & ndged)
Clear, Brown, Gold or Clear, Brown, Gold or
Black without tracer Black without tracer
Insulated wire (other than Insulated wire (other than E
green) with copper conductor een) with silver conductor Ц 9) —_— Threaded Ring
Notes: When parallel (SPTI & SPTIH) are used. The
Neutral wire is square shaped or ridged and the other wire
Will be round in shape or smooth (see us)
Warning:
Consult a qualified
Electrician for
installation
Light Loop
">
