TVS electronic | RP-3200 | User's Manual | TVS electronic RP-3200 User's Manual

TVS electronic RP-3200 User's Manual
3” Thermal Printer
Jus' Print RP-3200
All specifications are subject to change without notice
TVS electronics Ltd.
No 34, Developed Plots, South Phase, Industrial Estate, Guindy, Chennai - 600032
Toll Free no- 1800 103 2345
TABLE OF CONTENTS
1. Parts Identifications
3
2. Setting up the printer
4
2.1 Unpacking
4
2.2 Connecting the cables
5
2.3 Loading the roll paper
9
2.4 Dip switch setting
11
3. Control panel and other functions
18
3.1 Control panel
18
3.2 Error Indicating
18
4. Self Test
19
5. Hexadecimal Dump
20
6. Specifications
21
6.1. General Specifications
21
6.2. Auto Cutter Specifications
23
6.3. Interface
23
6.4. Electrical Characteristics
23
6.5. Environmental Requirements
24
6.6. Reliability
24
6.7. Certification
24
7. Command List
25
Jus' Print RP-3200 User’s Manual
1. Parts Identifications
3
Jus' Print RP-3200 User’s Manual
2. Setting Up the Printer
2-1. Unpacking
Your printer box should include these items. If any items are damaged or missing, please
contact your dealer for assistance.
The Printer
Adaptor (Option)
4
User’s Manual
Roll Paper
Interface Cable (optional)
Jus' Print RP-3200 User’s Manual
2-2. Connecting the Cables
Your printer box should include these items. If any items are damaged or missing, please
contact your dealer for assistance.
Before connecting any of the cables, make sure that both the printer and the computer are
turned off.
5
Jus' Print RP-3200 User’s Manual
2-2-1. Interface Connector
<D-SUB 25 Female Serial>
<Centronics Parallel>
<USB “B” Type>
<Ethernet>
<USB COMBO>
<Wi-fi>
Serial Interface
PIN
2
3
4, 20
6
1, 7
SIGNAL
TXD
RXD
DTR
DSR
GND
I/O
Output
Input
Output
Input
-
DESCRIPTION
Printer transmit data line RS-232C level
Printer receive data line RS-232C level
Printer handshake to host line RS-232C level
Data Send Ready
System Ground
USB Interface
PIN
1
2
3
4
6
SIGNAL
+5V
DATADATA+
GND
I/O
-
DESCRIPTION
+5V
Printer transmit data line
Printer transmit data line
System Ground
Jus' Print RP-3200 User’s Manual
Centronics Parallel Interface
PIN
1
2~9
10
11
12
13
14
15
16
17
18
19~30
31
32
33
34
35
36
SIGNAL
STROBEDATA0~7
ACKBUSY
PE
SELECT
AUTO FEEDGROUND
GROUND
NC
LOGIC-H
GROUND
INITERRORGROUND
NC
+5V
SELLECT IN-
I/O
Input
Input/Output
Output
Output
Output
Output
Input
Input
Output
Input
DESCRIPTION
Synchronize signal Data received
Data bit Transmitted 0~7
Data receiving completed.
Impossible to print of data receiving.
Paper empty
Printer status for ON/OFF line
Paper auto feed signal
System ground
System ground
+5V
System ground
Initialize
Printer error
System ground
+5V
Printer select signal
Ethernet Interface
PIN
1
2
3
4
5
6
7
8
SIGNAL
Data Out +
Data Out GND
Data IN +
Data IN N.C
N.C
N.C
I/O
Output Data +
Output Data Ground
Input Data +
Input Data -
7
Jus' Print RP-3200 User’s Manual
2-2-2. Cash Drawer Connector
The printer can operate two cash drawers with a 6 pin RJ-11 modular connector.
The driver is capable of supplying a maximum current of 1.0A/24VDC for 510ms or less when
not printing.
PIN
1
2
3
4
5
6
SIGNAL
Signal GND
Drawer kick-out drive signal 1
Drawer open/close signal
+24V
Drawer kick-out drive signal 2
Signal GND
DESCRIPTION
Output
Input
Output
-
Caution : To avoid an overcurrent, the resistance of the drawer kick-out solenoid
must be 24 Ω or more.
8
Jus' Print RP-3200 User’s Manual
2-3. Loading the Roll Paper
Notes: Be sure to use paper rolls that meet the specifications. Do not use paper rolls
that have the paper glued to the core because the printer cannot detect the paper end
correctly. (Turn off power switch)
1. Make sure that the printer is not receiving data; Otherwise, data may be lost.
2. Open the paper roll cover by pushing down the cover open button.
3. Remove the used paper roll core if there is one inside.
4. Insert new paper roll as shown.
9
Jus' Print RP-3200 User’s Manual
5. Pull out a small amount of paper, as shown. Then, close the cover.
6. Tear off the paper as shown.
10
Jus' Print RP-3200 User’s Manual
2-4. Dip Switch Setting
The printer is set up at the factory to be appropriate for almost all users. On the other hand,
offers some more settings for users with special requirements.
It has DIP switches that allow you to change communication setting, such as handshaking and
parity check, as well as print density.
Your printer has two sets of DIP switches. The functions of the switches are shown in the
following tables.
♣Note : Power off. And open the cover of Dip Switch and change setting.
2-4-1. Serial Interface Specification
DIP Switch Set 1 Functions
SW
1
2
3
4
5
6
FUNCTION
Data Receive
Hexadecimal
Hand Shaking
Data Length
Parity Check
Parity Check
ON
Ignored
HEXDUMP
XON/XOFF
7bits
ENABLED
EVEN
OFF
Print “?”
NORMAL
DTR/DSR
8bits
DISABLED
ODD
DEFAULT
OFF
OFF
OFF
OFF
OFF
OFF
Baud rate selection
Transmission speed
4800 bps
9600 bps
19200 bps
38400 bps
SW-7
ON
OFF
ON
OFF
SW-8
ON
ON
OFF
OFF
Print Density (DIP-SW2)
Print Density
Low Power
Normal
Normal
Dark
SW-1
ON
OFF
ON
OFF
SW-2
ON
ON
OFF
OFF
11
Jus' Print RP-3200 User’s Manual
2-4-2. Parallel Interface Specification
DIP Switch Set 1 Function
SW
2
5
FUNCTION
Hexadecimal
Bi-Parallel mode
ON
HEXDUMP
DISABLED
OFF
NORMAL
ENABLED
DEFAULT
OFF
OFF
Print Density (DIP-SW2)
Print Density
Low Power
Normal
Normal
Dark
12
SW-1
ON
OFF
ON
OFF
SW-2
ON
ON
OFF
OFF
Jus' Print RP-3200 User’s Manual
2-4-3. USB COMBO Interface Specification
DIP Switch Set 1 Function
SW
2
FUNCTION
Hexadecimal
ON
HEXDUMP
OFF
NORMAL
DEFAULT
OFF
COMBO Serial Option
SW
3
4
5
6
FUNCTION
HANDSHAKING
DATA LENGHT
PARITYCHECK
PARITYCHECK
ON
XON/XOFF
7BITS
ENABLED
EVEN
OFF
DTR/DSR
8BITS
DISABLED
0DD
Baud rate selection
Transmission speed
4800 bps
9600 bps
19200 bps
38400 bps
SW-7
ON
OFF
ON
OFF
SW-8
ON
ON
OFF
OFF
Print Density (DIP-SW2)
Print Density
Low Power
Normal
Normal
Dark
SW-1
ON
OFF
ON
OFF
SW-2
ON
ON
OFF
OFF
13
Jus' Print RP-3200 User’s Manual
2-4-4. USB Interface Specification
DIP Switch Set 1 Function
SW
2
FUNCTION
Hexadecimal
ON
HEXDUMP
OFF
NORMAL
DEFAULT
OFF
Print Density (DIP-SW2)
Print Density
Low Power
Normal
Normal
Dark
SW-1
ON
OFF
ON
OFF
SW-2
ON
ON
OFF
OFF
2-4-5. Wi-fi Interface Specification
DIP Switch Set 1 Function
SW
2
FUNCTION
Hexadecimal
ON
HEXDUMP
OFF
NORMAL
DEFAULT
OFF
Print Density (DIP-SW2)
Print Density
Low Power
Normal
Normal
Dark
14
SW-1
ON
OFF
ON
OFF
SW-2
ON
ON
OFF
OFF
Jus' Print RP-3200 User’s Manual
2-4-6. Ethernet Interface Specification
DIP Switch Set 1 Function
SW
2
FUNCTION
Hexadecimal
ON
HEXDUMP
OFF
NORMAL
DEFAULT
OFF
Print Density (DIP-SW2)
Print Density
Low Power
Normal
Normal
Dark
SW-1
ON
OFF
ON
OFF
SW-2
ON
ON
OFF
OFF
DIP Switch Set 2 Functions
Cutter
SW
3
FUNCTION
Cutter
ON
FULL CUT
OFF
PARTIAL CUT
Remarks
Only Epson mode
SW-4
OFF
SW-5
OFF
Emulation
FUNCTION
Epson (TM-88)
Paper low detect
SW
6
FUNCTION
Paper Low
ON
Detect
OFF
Do not Detect
15
Jus' Print RP-3200 User’s Manual
♣CAUTION:
Turn off the printer while removing the DIP switch cover to prevent an electric short, which can
damage the printer.
1. Make sure the printer is turned off.
2. Remove the screw from the DIP switch cover. Then, take off the DIP switch cover as shown
in the illustration below.
3. Set the switches using a pointed tool, such as tweezers or a small screwdriver.
4. Replace the DIP switch cover. Then, secure it with the screw.
The new settings take effect when you turn on the printer.
16
Jus' Print RP-3200 User’s Manual
♣CAUTION:
When the paper is jammed with cutter, the top cover might be stuck. In this case, repeat power
on and off several times.
If the top cover is still stuck, please follow the steps to release the papers from jamming.
1. Make sure the printer is turned off.
2. Take out cutter cover as shown.
3. Turn screw with drivers to a direction until paper is released from the cutter.
17
Jus' Print RP-3200 User’s Manual
3. Control panel and other functions.
3-1. Control panel
You can control the basic paper feeding operations of the printer with the button on the control
panel. The indicator lights help you to monitor the printer’s status.
Control Panel
POWER
ERROR
PAPER
Button
The button can be disabled by the ESC c 5 command.
Press the FEED button once to advance paper one line. You can also hold down the FEED
button to feed paper continuously.
3-2. Error indicators
This section explains the different patterns signaled by the three LED indicators located on
the top cover of the printer.
PAPER
RED
ERROR
RED
POWER
GREEN
Power off
OFF
OFF
OFF
Power on
OFF
OFF
ON
On line
Cover open
Paper empty
Paper near end
Test mode
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
STATUS
18
REMARKS
Normal power is not supplied to
the printer
Normal power is supplied to the
printer
Normal error-free mode
Close cover
Insert new paper roll
Paper is low
Ignored error led
Jus' Print RP-3200 User’s Manual
4. Self Test
The self-test lets you know if your printer is operating properly. It checks the control circuits,
printer mechanisms, print quality, ROM version and DIP switch settings.
This test is independent of any other equipment or software.
Running the self test
1. Make sure the printer is turned off and the printer cover is closed properly.
2. While holding down the FEED button, turn on the printer using the switch on the front of
the printer to begin the self-test. The Self Test prints the printer settings and then prints the
following, Cuts the paper, and pauses. (Error LED On)
Self test Printing
Please press the PAPER FEED button.
3. Press the FEED button to continue printing.
The printer prints a pattern using the built-in character set.
4. The self test automatically ends and cuts the paper after printing the following.
*** Completed ***
The printer is ready to receive data as soon as it completes the self-test.
19
Jus' Print RP-3200 User’s Manual
5. Hexadecimal Dump
This feature allows experienced users to see exactly what data is coming to the printer. This
can be useful in finding software problems.
When you turn on the hex dump function, the printer prints all commands and other data in
hexadecimal format along with a guide section to help you find specific commands.
To use the hex dump feature, follow these steps
1. After you make sure that the printer is off and Dip s/w 1-2 is ON, turn on the printer.
2. Run any software program that sends data to the printer. The printer prints “Hexadecimal
Dump” and then all the codes it receives in a two-column format. The first column contains the
hexadecimal codes and the second column gives the ASC้Gcharacters that correspond to
the codes.
Hexadecimal Dump
1B 21 00 1B 26 02 40 40 .!..& . @ @
1B 25 01 1B 63 34 00 1B .%.. c4 ..
41 42 43 44 45 46 47 48 ABCDEFGH
‫͑ػ‬A period (.) is printed for each code that has no ASC้equivalent.
3. Turn off the printer, and make sure that Dip sw 1-2 off.
4. Turn on the printer.
20
Jus' Print RP-3200 User’s Manual
6. Specifications
Appendix A : Specifications
6-1. General Specifications
(1) Printing Method
Direct line thermal printing.
(2) Print speed
200mm/sec.
(3) Dot density
180 DPI (Hor / Ver)
180 / 180 (0.141mm / 0.141mm dot)
203 DPI (Hor / Ver)
203 / 180 (0.125mm / 0.141mm dot)
(4) Printing Width
180 DPI
Max 72mm (512 dots)
203 DPI
Max 72mm (576 dots)
(5) Number of print columns.
No. of columns
Font “A”
Font “B”
180 DPI
42
56
203 DPI
48
64
(6) Roll paper
Refer to chapter 2 for details on the recommended roll Paper.
Paper width: 50mm ~ 82.5mm
Roll diameter : Max. Ø102.0 mm
(7) Weight
1.7Kg
21
Jus' Print RP-3200 User’s Manual
(8) Overall dimension
22
Jus' Print RP-3200 User’s Manual
6-2. Auto Cutter Specifications
(1) Cutting Frequency
Max. 30 cuts per minute
(2) Thickness of paper
0.065 ~ 0.1 mm
(3) Cutter Life
1.0 million cuttings
(if the paper thickness is between 65 and100µm)
6-3. Interface
RS232C Serial Interface, Centronics Parallel Interface(IEEE1284), USB Interface
USB COMBO Interface, Ethernet Interface(10Mbps), Wi-fi(802.11b)
6-4. Electrical Characteristics
(1) Input Voltage
DC 24V ± 10%
(2) Current Consumption
Operating: Approx. 1.5 A (at ASCଧGprinting)
Peak : Approx. 10 A
(at print duty 100%, For 10 seconds or less)
Stand-by : Approx. 0.15 A
(3) Power Connector
23
Jus' Print RP-3200 User’s Manual
! Important!
When connecting or disconnecting the power supply from the printer, be sure that the
following cautions are observed.
(1) Use a power supply (Limited Power Supply) of DC 24V±10% and more than 2.5A.
(2) Be careful about installing the printer in an area where there is noise.
(3) Take the appropriate measure to protect against electrostatic AC line noise, etc.
6-5. Environmental Requirements
(1) Operating
Temperature
Humidity
5°C to 40°C
10% to 90% RH (without condensation)
(2) Transport/Storage (except paper)
Temperature
-20°C to 60°C
Humidity
10% to 90% RH (without condensation)
6-6. Reliability
(1) MCBF
60 million lines (based on an average printing rate of 12.5% with paper
thickness in the range of from 65µm - 75µm)
35 million lines (based on an average printing rate of 12.5% with paper
thickness in the range of from 76µm - 150µm)
(2) Head Life
100 million pulses, 100Km
(3) Cutter Life
1.0 million cuttings (if the paper thickness is between 65 and 100µm)
6-7. Certification
(1) FCC PART15 CLASS A
(2) CE EMCD/LVD
(3) UL/cUL
(4) MIC
(5) RoHS
24
Jus' Print RP-3200 User’s Manual
7. Command List
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Command
HT
LF
CR
FF
CAN
DLE EOT
DLE ENQ
DLE DC4
ESC FF
ESC SP
ESC !
ESC $
ESC %
ESC &
ESC *
ESC ESC 2
ESC 3
ESC =
ESC ?
ESC @
ESC D
ESC E
ESC G
ESC J
ESC L
ESC M
ESC R
ESC S
ESC T
ESC V
ESC W
ESC ନ
ESC a
ESC c 3
ESC c 4
ESC c 5
ESC d
Function
REMARKS
Horizontal tab
Print and line feed
Print and carriage return
Print and return to standard mode(in page mode)
Cancel print data in page mode
Real-time status transmission
Real-time request to printer
Generate pulse at real-time
Print data in page mode
Set right-side character spacing
Select print mode(s)
Set absolute print position
Select/cancel user-defined character set
Define user-defined characters
Set bit-image mode
Turn underline mode on/off
Select default line spacing
Set line spacing
Select peripheral device
Cancel user-defined characters
Initialize printer
Set horizontal tab positions
Turn emphasized mode on/off
Turn double-strike mode on/off
Print and feed paper using minimum units
Select page mode
Select character font
Select an international character set
Select standard mode
Select print direction in page mode
Turn 90° clockwise rotation mode on/off
Set printing area in page mode
Set relative print position
Select justification
Select paper sensor(s) to output paper-end signals
Select paper sensor(s) to stop printing
Enable/disable panel buttons
Print and feed paper n lines
25
Jus' Print RP-3200 User’s Manual
No.
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
1
2
3
4
5
6
7
8
9
10
26
Command
ESC p
ESC t
ESC {
FS p
FS q
GS !
GS $
GS *
GS /
GS B
GS H
GS I
GS L
GS P
GS V
GS W
GSGନ
GS a
GS f
GS h
GS k
GS r
GS v 0
GS w
< Add >
ESC i
ESC m
FS !
FS &
FS FS .
FS 2 c1 d1…dk
FS C
FS S 1 2
FS W
Function
General pulse
Select character code table
Turn upside-down printing mode on/off
Print NV bit image
Define NV bit image
Select character size
Set absolute vertical print position in page mode
Define downloaded bit image
Print downloaded bit image
Turn white/black reverse printing mode on/off
Select printing position of HRI characters
Transmit printer ID
Set left margin
Set horizontal and vertical motion units
Select cut mode and cut paper
Set printing area width
Set relative vertical print position in page mode
Enable/disable Automatic Status Back(ASB)
Select font for HRI characters
Set bar code height
Print bar code
Transmit status
Print raster bit image
Set bar code width
Full cut
Partial cut
Set print mode(s) for Kanji characters
Select Kanji character mode
Turn underline mode on/off for Kanji character
Cancel Kanji character mode
Define user-defined Kanji characters
Select Kanji character code system
Set Kanji character spacing
Turn quadruple-size mode on/off for Kanji character
REMARKS
Rev. 2.0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising