2017 Jeep Buyer`s Guide - 11.3 Mb
©Tenneco 2017. Printed in the USA R-RM0101-0817-J
2017-07 WRANGLER JK & JK UNLIMITED 4WD
WRANGLER JK & JK UNLIMITED 4WD 2017-07
For The Ultimate Off-Road Experience
4-IN. CRAWLER LONG ARM SYSTEM
Fits up to 37-in. tires
Front and rear progressive rate coil springs
Fully adjustable upper and lower control arms w/ D2 bushings
Extended length front and rear sway bar end link
Heavy-duty front and rear adjustable track bars
Upgraded front and rear bump stop spacers
Front and rear extended length brake lines
High-articulation front and rear long arm design
Adjustable front and rear upper link design
Will not affect the Electronic Stability Control System
No exhaust modifications required for 2011-2007
Brackets are high-strength, low-alloy steel
4-IN. CRAWLER SHORT ARM SYSTEM PART No. RS66114B
Fits up to 37-in. tires
Front and rear progressive rate coil springs
Fully adjustable upper and lower control arms w/ D2 bushings
Extended length front sway bar end link
Upgraded front and rear bump stop spacer
Heavy-duty front and rear adjustable track bars
Front extended length brake lines
Rear brake line drop brackets
Rear sway bar spacers included
Will not affect the Electronic Stability Control System
Brackets are high-strength, low-alloy steel
100-percent bolt-on system
Cross over exhaust pipe RS720003 required for 17-12 JK
Shocks sold separately:
RS5000™X
Front RS55331
Rear RS55332
RS7000 ®MT
Front RS7331
Rear RS7330
RS9000™XL
Front RS999331
Rear RS999332
DONT FORGET THE STEERING STABILIZER
see page S.22 and page S.24
PART No. RS66115B
Transmission Cross Member REQUIRED and sold separately.
Cross over exhaust pipe RS720003 required for 17-12 JK
Shocks and Transmission Cross Member sold separately:
RS5000™X
Front RS55331
Rear RS55332
Transmission Cross Member REQUIRED and sold separately.
TRANSMISSION CROSS MEMBER
PART NO. RS886101 OR RS886102
Cross Member
2011-07 RS886101
RS7000 ®MT
Front RS7331
Rear RS7330
RS9000™XL
Front RS999331
Rear RS999332
2017-12 RS886102
Not included in system. Must be purchased separately
DONT FORGET THE STEERING STABILIZER
see page S.22 and page S.24
D2 BUSHINGS
RANCHO D2 CONTROL ARM AND TRACK BAR BUSHINGS
SELF CENTERING - SELF LUBRICATING
STEEL SLEEVE
Re-enforces Poly bushing to self-center
sleeve and add durability
PTFE COATED
For lifetime grease-free operation
FULL FLOATING STEEL SLEEVE
J.2
Rancho RS66115B with 37-in. tires. Trimming or modification may be required to provide proper tire clearance.
Actual tire size varies between manufacturers. B designates black finish. **For more information visit gorancho.com
J.3
2017-07 WRANGLER JK & JK UNLIMITED 4WD
WRANGLER JK & JK UNLIMITED 4WD 2017-07
3 - 3.5-IN. PROGRESSIVE SPORT
4-IN. SPORT SYSTEM PART No. RS66102B
Fits up to 37-in. tires
Front and rear progressive rate coil springs
Rancho geometry correction brackets
Front adjustable track bar included
Extended length front sway bar end link
Upgraded front and rear bump stop spacer
Front extended length brake lines included
Rear axle track bar and brake line drop brackets
Rear sway bar spacers included
Will not affect the Electronic Stability Control System
Brackets are high-strength, low-alloy steel
100-percent bolt-on system
Fits up to 35-in. tires
Front and rear progressive rate coil springs
Front adjustable track bar included
Extended length front sway bar end link
Upgraded front and rear bump stop spacer
Front extended length brake lines included
Rear brake line drop brackets
Brackets are high-strength, low-alloy steel
Will not affect the Electronic Stability Control System
100-percent bolt-on system
Cross over exhaust pipe RS720003 required for 17-12 JK
Shocks sold separately:
RS5000™X
Front RS55331
Rear RS55332
RS7000 ®MT
Front RS7331
Rear RS7330
RS9000™XL
Front RS999331
Rear RS999332
DONT FORGET THE STEERING STABILIZER
see page 5 and page 7
PART No. RS66110B
Cross over exhaust pipe RS720003 required for 17-12 JK
Shocks sold separately:
RS5000™X
Front RS55329
Rear RS55330
RS7000 ®MT
Front RS7329
Rear RS7330
RS9000™XL
Front RS999329
Rear RS999330
2-IN. SPORT SYSTEM
Fits up to 33-in. tires
Front and rear progressive rate coil springs
Upgraded front bump stop spacer
RS5000™X or RS9000™XL Rancho Shocks included
Rear brake line drop brackets
Will not affect the Electronic Stability Control System
100-percent bolt-on system
PART No. RS66118BR5
PART No. RS66118BR9
JEEP WRANGLER JK 4WD 2 DOOR
JEEP WRANGLER JK 4WD 2 DOOR
RS5000™X Shocks and Coil Springs included.
RS9000™XL Shocks and Coil Springs included.
PART No. RS66119BR5
PART No. RS66119BR9
JEEP WRANGLER JK 4WD 4 DOOR
JEEP WRANGLER JK 4WD 4 DOOR
RS5000™X Shocks and Coil Springs included.
RS9000™XL Shocks and Coil Springs included.
UPGRADE YOUR SHOCKS.
YEAR
J.4
Rancho RS66102B with 37-in. tires. Trimming or modification may be required to provide proper tire clearance.
Actual tire size varies between manufacturers. B designates black finish. **For more information visit gorancho.com
MODEL
RAISED HEIGHT
RS5000TMX
RS7000®MT
RS9000TMXL
Front
Rear
Front
Rear
Front
Rear
2017-07 Wrangler JK 4WD
0 - 2-in.
RS55326
RS55328
RS7326
RS7328
RS999326
RS999328
2017-07 Wrangler JK 2WD
0 - 2-in.
RS55326
RS55328
RS7326
RS7328
RS999326
RS999327
2017-07 Wrangler JK 4WD
3 - 3.5-in.
RS55329
RS55330
RS7329
RS7330
RS999329
RS999330
2017-07 Wrangler JK 4WD
4-in.
RS55331
RS55332
RS7331
RS7330
RS999331
RS999332
J.5
2006-97 WRANGLER TJ/LJ 4WD
WRANGLER TJ/LJ 4WD 2006-97
3.5-IN. SHORT ARM SYSTEM
Experience the Rancho® difference and uncompromising performance on- and off-road with the redesigned Rancho® 3.5-inch Short
Arm Suspension Kit. This kit allows you to run up to 35-inch tires on your Wrangler TJ/LJ and it comes complete with a Pitman Arm,
Track Bar, Sway Bar Disconnects and NEW Adjustable Lower Control Arms. The NEW Control Arms allow for the adjustment of caster
and pinion angle and have forged ends featuring Rancho’s D2 grease-free synthetic high articulation bushings that self-center.
Complete your performance suspension by choosing the Rancho shocksthat best suit your driving needs! The Rancho brand
offers a Limited Lifetime Warranty** for this Suspension System.
2.5-IN. SPORT SYSTEM
Fits up to 33-in. tires
No exhaust modifications required
Brake line drop brackets
NEW adjustable lower control arms with D2 bushings
Front and rear coil springs
Transfer case shifter relocation brackets and drop
down spacers to allow use of factory drive-shafts
PART No. RS66113B
Shocks sold separately:
RS5000™X
Front RS55255
Rear RS55256
RS7000 ®MT
Front RS7255
Rear RS7256
RS9000™XL
Front RS999255
Rear RS999256
PROGRESSIVE RATE
COIL SPRINGS
COMING SOON
PART No. RS6503B
Shocks sold separately:
RS5000™X
Front RS55239
Rear RS55241
RS7000 ®MT
Front RS7239
Rear RS7241
RS9000™XL
Front RS999239
Rear RS999241
This suspension system was developed using a
33 x 12.5 x R15 tire on a 15 x 8-in. wheel with 3.75 B.S.
UPGRADE YOUR SHOCKS.
YEAR
J.6
Rancho RS66105B with 37-in. tires
MODEL
RAISED HEIGHT
RS5000TMX
RS7000®MT
RS9000TMXL
Front
Rear
Front
Rear
Front
Rear
2006-97 Wrangler TJ/LJ 4WD
0-in.
RS55128
RS55240
RS7128
RS7240
RS999128
RS999240
2006-97 Wrangler TJ/LJ 4WD
5 - 6-in.
-
-
RS7061
RS7062
RS999061
RS999062
Rancho RS6503B with 33-in. tires. Trimming or modification may be required to provide proper tire clearance.
Actual tire size varies between manufacturers. B designates black finish. **For more information visit gorancho.com
J.7
2001-84 CHEROKEE XJ 4WD
WRANGLER YJ 4WD 1996-86
WRANGLER CJ 4WD 1986-46
The 3.5-in. Rancho XJ Suspension System is the perfect choice for those who are looking to do some on- and off-road driving with their
Cherokee. The kit includes front upper adjustable control arms and lower control arms for increased strength over stock; replacement
front coil springs and rear leaf springs; front swaybar links; rear shackles; shims; U-bolts; extended length front brake lines and a rear
brake line to the axle; and a new front adjustable trackbar that helps to maintain proper geometry. The system also will allow you to run
31-in. tires without trimming or 33-in. tires with trimming. Pair this kit with your favorite
set of Rancho shocks and you have an XJ that will perform well on
the road and provide increased flexibility and versatility off road.
FEATURES
Allows for 31-in. tires untrimmed or 33-in. tires with trimming
Front extended length brake lines and a rear brake line to rear axle
Front upper and lower adjustable control arms w/ D2 bushings
Front adjustable trackbar
Heavy-duty DOM tubular lower control arms
Front coil springs and rear leaf springs
Front swaybar links
U-bolts, shims and drop shackles
For use with Rancho 2.5-in. Leaf Springs
Allows up to 33-in. tires
Rancho springs are designed to maintain a soft factory ride
Springs are carefully shot peened & finished in black
U-Bolt replacement kit also available.
Leaf spring bushings included
This suspension system was developed
using a 33 x 12.5 x R15 tire.
Leaf springs are designed to re-use factory U-bolts
Leaf springs are designed to control torque roll while providing equal traction through limited axle wind-up
Shocks sold separately:
RS7000 ®MT
Front RS7239
Rear
-
2.5-IN. SUSPENSION HARDWARE KIT
FEATURES
PART No. RS66002B/RS66003B
RS5000™X
Front RS55239
Rear RS55245
Rancho RS6444 with 33-in. tires
3.5-IN. PERFORMANCE SUSPENSION
RS9000™XL
Front RS999239
Rear RS999245
RS66002B is for use with the O.E. Chrysler rear axle.
RS66003B is for use with the O.E. Dana rear axle.
(Installation of a slip yoke eliminator and replacement
driveshaft on the stock transfer case is recommended).
PROGRESSIVE RATE
COIL SPRINGS
PART No. RS6444
For use with Rancho Leaf Springs RS44050 and RS44150:
Primary
Suspension System
RS6444
Front Springs Front Kits
RS44050
RS720
UPGRADE YOUR SHOCKS.
YEAR
COMING SOON
1996-86
1996-86
MODEL
Shocks sold separately:
Rear Springs
RS44150
RearKits
RS721
RAISED HEIGHT
Wrangler YJ 4WD
Wrangler YJ 4WD
RS5000™X
Front RS55168
Rear RS55118
RS5000TMX
Front
RS55168
RS55168
0 - 1.5-in.
2.5-in.
RS7000 ®MT
Front RS7168
Rear RS7118
RS7000®MT
Rear
RS55113
RS55118
Front
RS7168
RS7168
Rear
RS7113
RS7118
RS9000™XL
Front RS999168
Rear RS999118 316
RS9000TMXL
Front
RS999168
RS999168
Rear
RS999113316
RS999113316
2.5-IN. LEAF SPRING SYSTEM
FEATURES
Leaf springs are designed to control torque roll while providing equal traction through limited axle wind-up
Rancho springs progressively rated to control axle wind-up while maintaining a soft factory ride
All Rancho Leaf Springs come complete with urethane bushings and pre-installed Zinc plated sleeves
Springs are carefully shot peened and finished in black
Complete kit requires all four leaf assemblies
UPGRADE YOUR SHOCKS.
YEAR
MODEL
01-84
Wrangler XJ 4WD
01-84
Wrangler XJ 4WD w/ Rancho System
J.8
RAISED HEIGHT
RS5000TMX
RS7000®MT
RS9000TMXL
Front
Rear
Front
Rear
Front
Rear
0-in.
RS55128
RS55129
RS7128
RS7129
RS999128
RS999129
2.5-in.
RS55239
-
RS7239
RS7219
RS999239
RS999129
Rancho RS66002B with 33-in. tires. Trimming or modification may be required to provide proper tire clearance.
Actual tire size varies between manufacturers. B designates black finish. **For more information visit gorancho.com
YEAR
MODEL
RAISED HEIGHT
FRONT SPRINGS
FRONT KITS
REAR SPRINGS
REAR KITS
86-82
86-82
1981
1981
81-76
81-76
75-72
71-69
63-46
CJ5, CJ7, CJ8 4WD
CJ5, CJ7, CJ8 4WD
CJ8 4WD
CJ8 4WD
CJ5, CJ7 4WD
CJ5, CJ7 4WD
CJ5, CJ6 2/4WD
CJ5, CJ6 4WD
CJ2A, CJ3A, CJ3B 4WD
2.5-in.
1-in.
2.5-in.
1-in.
2.5-in.
1-in.
2.5-in.
2.5-in.
2.5-in.
RS44092
RS44092
RS44092
RS44062
RS44062
RS44020
RS712
RS712
RS712
RS712
RS712
RS712
RS712
RS712
RS714
RS44192
RS44192
RS44192
RS44162
RS44162
RS44120
RS711
RS711
RS711
RS711
RS711
RS711
RS713
RS713
RS711
316
Requires Rancho shock adapter bracket. See Master Catalog or website for additional application information.
J.9
ACCESSORIES
ACCESSORIES
HIGH-CLEARANCE STEERING KNUCKLES
ADJUSTABLE CONTROL ARMS
Rancho® has NEW front and rear, upper and lower Adjustable Control Arms for your stock or lifted Jeep. The new Arms work on a range
from stock to 4-inches and allow caster and pinion angle adjustments. The Arms are made of heavy duty DOM tubing for improved
strength to handle off road obstacles. Lower Arms are bent similar to the factory design to allow for larger wheels and tires.
The Control Arms forged ends feature Rancho’s D2 synthetic high articulation bushings that self-center and are completely grease free.
For the ultimate in convenience, a rebuild kit is available and sold separately.
FEATURES
The Rancho® High-Steer Knuckles maintain steering geometry and add strength to the most vulnerable points within the steering envelope
when off-road driving. The knuckles add an additional 1.5-inches of clearance within the tight space, helping to protect critical steering
components, and their design also helps lift the steering linkage out of range from direct impact from off-road obstacles or impediments.
The High-Steer Knuckles are precisely engineered and heavy-duty for Left Hand and Right Hand Drive, 3-inch and higher lifted Jeep
Wrangler JK’s. The kit includes: a front left High-Steer Knuckle, a front right High-Steer Knuckle and 3-inch bump stops. This product
offers a Limited Lifetime Warranty. A 3-inch Track Bar Relocation Bracket is required and is sold separately if your lift does not have
one (RS62101). A flipped drag link is also required and is sold separately (RS62102, RS62106).
FEATURES
Heavy duty, .188 DOM wall tubing & forged ends construction
1.25-in. OD Diameter bar for upper Arms
2.00-in. OD Diameter bar for lower Arms
D2 high articulation, grease-free, self-centering bushings
Improves ride quality reducing NVH
Works on Jeeps from stock to 4-inches of lift
Allows adjustment for caster and pinion angles
Sold in pairs by axle or as a complete set
PART No. RS62100
Fits JK Dana 30, JK Rubicon Dana 44
2017-07 JEEP WRANGLER JK 2/4
Adds critical strength and height to off-road JK’s
X, Sport, Sahara, Unlimited and Rubicon Models
Constructed from high-strength steel
Compatible for left- and right-hand drive models
Aligns the geometry of the track bar & drag link to reduce bump steer
Requires use of 3-in. track bar mount – (sold separately)
Requires use of a flip drag link – (sold separately)
Limited Lifetime Warranty**
DOOR with 3 - 4-in. Lift Height
TRACK BAR BRACKET
PART No. RS66159B
17-07 WRANGLER JK 2/4 DOOR with 0 - 4-in. Lift Height
Also sold individually in pairs:
Front Upper
Front Lower
RS66155B
RS66156B
06-97 WRANGLER TJ/LJ/XJ with 0 - 4-in. Lift Height
01-84 CHEROKEE XJ with 0 - 4-in. Lift Height
Sold in pairs by axle:
Rear Upper
RS66157B
Rear Lower
RS66158B
Front Upper
RS66160B
Front Lower
RS66161B
Rear Upper
RS66162B
Rear Lower
RS66163B
Cherokee XJ is front upper and lower only.
Rancho®’s new adjustable Track Bars work on lift kits from 2- to 6-inches and allow you to center your Jeep JK’s front or rear axle in
the proper position. The D2 synthetic, high articulation bushings in the Track Bar deliver superior dampening plus improved ride and
handling characteristics. The D2 bushing has a firmer inner bearing material and a softer outer material to dampen noise, vibration, and
harshness (NVH). The D2 bushing is grease free with a liner impregnated into the internal bushing that serves as a lubricating agent for
silent, maintenance free operation.
PART No. RS62104 (Frt) RS62105 (Rear)
Heavy duty, .281 DOM wall tubing & forged ends construction 17-07 JEEP WRANGLER JK 2/4 DR. w/ 2 - 6-in. Lift Height
Includes D2 bushings for long life & improved ride experience
Wrangler, Wrangler Unlimited and Rubicon Models
Improves ride quality reducing NVH
Centers the axle in the axle position
1.25-in. OD Diameter Bar
PART No. RS62104
FEATURES
Compatible with 3-in. and taller lifts
Heavy-duty Front Track Bar Bracket for the Jeep JK
This bracket raises the vehicle’s axle side track bar mount
ADJUSTABLE TRACK BAR
FEATURES
Dramatically improve a lifted Jeep JK’s overall handling and reduce body roll through the Rancho Track Bar Relocation Bracket.
After lifting a Jeep JK, the vehicle’s roll center is raised and this heavy-duty front track bar bracket helps to restore proper suspension
geometry and raises the vehicle’s axle side track bar mount. Built to the Rancho brand’s exacting standards of engineering and materials, the bolt-on bracket helps to strengthen the factory mount for heavy off-road use. The bracket – easily installable with basic hand
tools – relocates the factory or aftermarket steering stabilizer to a higher, less-susceptible-to-impact
location. The Rancho Track Bar Bracket features a powder-coat finish. All Rancho® RockGEAR™
components are covered by a Limited One Year Warranty**.
PART No. RS62101
2017-07 JEEP WRANGLER JK 2/4 DOOR with 3 - 4-in. Lift Height
X, Sport, Sahara, Unlimited and Rubicon Models
FLIP DRAG LINK FOR VEHICLES WITH RANCHO HIGH-CLEARANCE STEERING KNUCKLES
FEATURES
Mounts in the steering knuckle and connects to the adjusting sleeve/inner tie rod at the pitman arm
RS62106 can be used as a O.E. stock replacement drag link on LHD vehicles
Dana 30 or Dana 44 axle
Grease-able
(LHD)
(RHD)
Lifetime Warranty**
PART No. RS62102
RS62106
2017-07 JEEP WRANGLER JK 2/4 DOOR
PART No. RS62105
J.10
**For more information visit gorancho.com
Wrangler, Wrangler Unlimited and Rubicon Models
J.11
ACCESSORIES
GEOMETRY CORRECTION BRACKETS
Rancho® Jeep JK Geometry Correction Brackets deliver perfect fit, finish and performance. These next-level Rancho Jeep JK Geometry
Correction Brackets keep the control arms at factory angles to deflect road harshness, reduce brake dive and allow for proper caster angle
after the addition of an aftermarket lift kit…maximizing the performance of your Jeep Wrangler JK. This NEW bracket fits Jeeps running lift
kits from 2- to 4-inches utilizing our unique 4-hole upper control arm locator. Rancho engineering fit and finish delivers a one-piece welded
design that will bolt up directly to the factory locations out of the box, saving you time and aggravation.
FEATURES
Works on 2- to 4-inch lift kits that utilize factory upper and lower control arms
Fixed adjustment location for each height with an option for additional caster if needed
No assembly required! Out of box and on to your Jeep…an easy DIY project!
Corrects control arm alignment geometry to factory specs eliminating the need for
adjustable control arms or cam bolts for caster correction
One-piece welded design with a durable, black power-coated finish
PART No. RS62103
2017-07 JEEP WRANGLER JK 2/4 DOOR
Wrangler, Wrangler Unlimited and
Rubicon Models with 2 - 4-in. Lift Height
ACCESSORIES
FRONT COIL SPRING SPACER KIT
FEATURES
3/4-in. Coil Spring Spacer Kit
PART No. RS70082
2017-07 JEEP WRANGLER JK 2/4 DOOR
2006-97 JEEP WRANGLER TJ/LJ
Available in black finish only. Shocks sold separately.
CROSS OVER EXHAUST PIPE KIT
FEATURES
Clearance is optimized for 2 - 5-in. lifted 17-12 Jeep Wranglers, 3.6L V6 engine
Prevents contact between the exhaust cross over pipe and front drive shaft
Allows more drive shaft clearance & suspension down travel than exhaust spacers
Includes all necessary clamps, hardware, and detailed installation instructions
Mandrel-bent 409 Stainless steel tubing
Retains equalized OEM down pipe
PART No. RS720003
2017-12 JEEP WRANGLER JK 2/4 DOOR
Required for 3.6L V6 Models with 2 - 5-in. lift height
FRONT QUICK DISCONNECT SWAY BAR LINKS
FEATURES
Designed for Wranglers with 3 - 4-in. lift height
Quick release lynch pin design
Heavy-duty construction
Allows you to disconnect front sway bar for additional suspension travel
PART No. RS6756B
2017-07 JEEP WRANGLER JK 2/4 DOOR
Non-Rubicon models only
FRONT AXLE BUSHING KIT
FEATURES
Replacement press-in O.E. Bushings for front axle
Replace in pairs with bolts included
Restores O.E. ride quality
PART No. RS906
2017-07 JEEP WRANGLER JK 2/4 DOOR
EXTENDED LENGTH BRAKE LINES
FEATURES
Stainless steel braided Brake Lines are protected with a vinyl cover
Provides a firmer and more responsive braking
Mounting brackets included where necessary
Sold in pairs
PART No. RS6247 OR RS6248
2017-07 JEEP WRANGLER JK 2/4 DOOR
Front RS6247 (24.5-INCH)
Rear RS6248 (22-INCH)
PART No. RS6249
2006-97 JEEP WRANGLER TJ/LJ
2001-84 JEEP CHEROKEE XJ
Front RS6249 (21.5-INCH)
J.12
J.13
ROCKGEAR™
WRANGLER JK - WRANGLER TJ/LJ
TUBE DOORS
Added visibility for off-road
Retains factory side mirror (passenger and driver side)
1.25-in. tube construction
Mounts to O.E. door hinge
O.E. style latch that can be opened from inside or outside
Durable textured black powder-coated finish
CONTROL ARM SKIDS
2017-07 JEEP WRANGLER JK 2/4 DOOR
2017-07 JEEP WRANGLER JK 2/4 DOOR
2006-97 JEEP WRANGLER TJ/LJ
DANA 30
Front RS6222
(DOOR SKINS AVAILABLE AT spiderwebshade.com)
2017-07 JEEP WRANGLER JK 2/4 DOOR
2006-97 JEEP WRANGLER TJ/LJ
2017-07 JK
Front RS6216B
Rear RS6217B
DIFFERENTIAL GLIDE PLATE
Mounts to front axle casting
Protects casting from direct contact
Works with O.E. and most aftermarket differential covers
Durable red powder-coated finish
Allows for a smoother glide over obstacles forwards and backwards
DANA 44
Front RS6212
Rear RS6242
Mounts to front lower control arms (axle end)
Reduces hang-ups and damage to the factory brackets
Thick 3/16-in. Steel construction
Durable red powder-coated finish
Bolts-on in minutes
Front RS6210
2006-97 JEEP WRANGLER TJ/LJ
2006-97 TJ/LJ
Part No. RS6223B
DANA 30
Front RS6227
DANA 44
Front RS6228
Notes: Tube doors are sold in pairs. Rancho recommends checking local and states laws
before installation of this product. Such laws may prohibit installation of this product.
Warning: This product is intended for off-road use only. It is not designed as a safety restraint
device. Always wear your seat belts, and avoid sharp turns and other abrupt maneuvers.
DIFFERENTIAL COVER
REAR DOOR COVER PLATE
LED REAR BRAKE LIGHT
Works with Rancho bumpers
Compatible with any 2.25-in diameter hole
Works with factory wiring, all necessary wires and
connectors are included with kit
2017-07 JEEP WRANGLER JK 2/4 DOOR
2006-97 JEEP WRANGLER TJ/LJ
J.14 Part No. RS6238
Protects rear decompression vent
CB antenna mount included
Reuses factory bolts and hole locations
Designed to cover vent when removing spare tire carrier
Thick Steel construction
Black color looks sharp
2017-07 JEEP WRANGLER JK 2/4 DOOR
2006-97 JEEP WRANGLER TJ/LJ
2017-07 JK
RS6237B
2006-97 TJ/LJ
RS6233B
OIL PAN PROTECTION
Protects the oil pan from direct contact
1/8-in. Steel construction
Easy installation, installs over O.E. oil pan
Shields the entire oil pan and maintains drain-hole access
Durable red powder-coated finish
NEW mounting tab to keep armor in place
2017-07 JEEP WRANGLER JK 2/4 DOOR
2017-12 JK
RS6236
2011-07 JK
RS6208
Added axle and internal gear protection
Manufactured from high-strength nodular Iron
Ribbed external construction for added strength
Durable red powder-coated finish
Off-set over-sized fill plug for increased fluid capacity
and easier/quicker filling
2017-07 JEEP WRANGLER JK 2/4 DOOR
2006-97 JEEP WRANGLER TJ/LJ
DANA 30
Front RS6218
DANA 44
Front RS6209
DANA 60
Factory 10-bolt pattern RS6245
*On RHD vehicles, the Steering Stabilizer must be moved from below the tie rod to a
high clearance location to use this part. Rancho part number RS64100 High-Clearance
Bracket with RS5401 Steering Stabilizer can be used to achieve this.
For more information visit gorancho.com.
J.15
RS5000™X SHOCK ABSORBER
CROSS-TUNED TECHNOLOGY
Inside the new, innovative Rancho® RS5000™X shock is a unique, patented valving system and advanced
compression functionality. Developed by the engineers at Rancho, The Rancho RS5000X Cross-Tuned
Technology will improve the vehicle’s overall on- and off-road handling and performance.
PROGRESSIVE ENGAGEMENT VALVING
(Rebound Cycle)
PROGRESSIVE ENGAGEMENT VALVING
(Compression Cycle)
PROGRESSIVE ENGAGEMENT VALVING:
The Rancho RS5000X Series design includes patented progressive rebound and compression discs. At lower speeds or in the earlier
stages of the Shock’s travel, an eccentric disc in the valve shim stacks will engage the valving at lower frequencies, helping to
control the energy of motion as the cycle of the Shock increases or decreases in its action.
The sintering process forms
objects from powders using atomic
diffusion. The powdered material
is heated to just below its melting
point, fusing all of the particles
together to create the piston.
This process brings increased
structural conformity to each
Rancho RS5000X piston.
The RS5000X composite piston
band provides smoother piston
travel and greater responsiveness
to changing road conditions. Each
glass-filled band offers incredibly
smooth operation within the shock
absorber cylinder due to Fluon, a
slippery glass and plastic material.
Each RS5000X series shock has a
high-strength, polyurethane bumper
that helps control the rebound
motion during harsh driving conditions. The rebound bumper greatly
reduces wear and tear during onand off-road driving. When your
shock rebounds from an obstacle at
an excessive rate, the polyurethane
bumper dampens the piston rod
cycle at its peak point of travel.
Every Rancho RS5000X shock piston rod is strengthened through a
nitro-carburizing process. From increased scuffing resistance to additional protection against corrosion,
the process enhances the shock’s
overall durability. Nitro-carburizing
also is more environmentally
friendly than the chroming
process.
Each Rancho RS5000X series shock
includes a red polyvinyl accordion
protection boot, adding protection
to the shock rod and oil seal during
on- and off-road driving.
GREAT ALL AROUND UPGRADE
OR REPLACEMENT SHOCK
When hitting a pothole, off-road trail obstacle or similar activity, Rancho’s Progressive Engagement Valving allows for early flow
of fluid, helping to reduce harsh initial impacts and to control the flow of fluid in a progressive, gradual manner through the valving.
During on- or off-road driving activities like washboard roads or when traveling a rough fire road, the early flow of fluid helps to
minimize a “rough” ride as the piston movement is able to glide through the initial travel motion of the Shock with minimal ground
impact or force. If needed, the Progressive Engagement Valving will further engage to maintain control and stability.
The bushings used on the Rancho
RS5000X series shocks provide
additional ride harshness absorption and reduce transmitted road
noise and suspension vibration
to result in a smoother ride and
longer life for shocks and related
suspension components.
The RS5000X series features
a 2-1/4-inch diameter shock
body. A larger shock body allows
for increased fluid capacity to
operate cooler and to increase
vehicle control and performance at
varying speeds and terrains. The
RS5000X series combines a larger
shock body with all-weather fluid,
allowing the shock to withstand
internal temperatures between -40
and 248 degrees Fahrenheit.
S.16
The Tuned Compression Control
Valve is a custom-tuned, clamped
disc base valve that regulates
fluid transfer during the shock’s
compression cycle to help absorb
impacts without disc flutter and
to help maintain vehicle control
in virtually any environment. The
precision-tuned shim stacked
valving allows the motion of the
shock to work in harmony with the
vehicle during on- and off-road
driving.
Each RS5000X shock is gas pressurized to 150 PSI.* The twin tube,
gas pressurized shock has a variety
of advantages including minimizing
air-to-oil mixture that can cause
foaming and shock fade. Gas
pressurization also provides a mild
boost of spring rate to the vehicle.
The low-friction, self-lubricating
seal included in the RS5000X shock
retains gas and oil to help prolong
performance and allow for quicker
rebound and smoother compression during the shock cycle. This
seals provides an extra layer of
defense against dirt and debris.
Rancho engineers place extra
emphasis on welded construction
at stress areas – like mounting
points – of the RS5000X shock.
Each shock includes double-welded loops for added strength and
durability.
ALSO AVAILABLE AS A
PERFORMANCE STRUT
The RS5000X’s 35 mm bore helps
to provide heightened control of
shock motion due largely to the expanded piston area. Full-displaced
compression valving allows the
piston to displace more fluid than
traditional rod displaced valving.
Rancho RS5000X series struts
include 60PSI of gas pressurization.
**
For more information visit gorancho.com
S.17
RS7000®MT SHOCK ABSORBER
FREE-FLOATING DIVIDING PISTON
Reduces the possibility of aeration and shock fade
MONOTUBE DESIGN
14mm hardened Steel piston rod
for superior strength over standard
11mm rods.
Unique integral hydraulic lockout
cushions piston impact when
vehicle suspension is fully
extended.
Full-floating dividing piston and
high pressure Nitrogen gas maintains constant pressure against the
hydraulic oil, eliminating possible
aeration and shock fade.
Brushed Zinc plated finish with
durable clear coat provides long
lasting great looks.
Protective black rubber boot shields Black natural rubber bushings for
piston rod from dirt and debris.
enhanced durability and reduced
road harshness.
46mm Bore Monotube construction
- Ideal for larger light trucks, SUVs
and more.
HYDRAULIC LOCKOUT
Cushions impact at suspension travel limits
Specifically engineered for high center of gravity light trucks and SUV’s to provide the handling, control and performance expected
from Rancho® RS7000®MT Shock Absorbers. The Rancho RS7000MT Monotube Shock Absorbers provide enhanced stability over
stock twin tubes by reducing body roll in evasive maneuvers and tight turns. These Shocks feature a high-pressure gas charge that
separates the unit’s internal oil and Nitrogen to provide additional spring rate. This helps to maximize damping response
that dissipates heat for better control.
To further enhance ride control characteristics, Rancho RS7000MT Monotube Shocks include a hydraulic lockout to cushion the
impact as the vehicle suspension is fully extended. The series is covered by a Limited Lifetime Warranty and 90-Day Free-Ride Offer**.
ALSO AVAILABLE AS A
Internally bushed steel rod guide
with temperature resistant two
piece seal design improves sealing
over conventional single seals
during extreme side-loads.
HIGH CONTROL SHOCK REDUCES ROLL AND SWAY
PERFORMANCE STRUT
Huge 46mm working piston with
Fluon band for consistent sealing
between the piston and monotube
which delivers better control
and increased durability compared
to conventional piston designs.
S.18
Monotube design with high
pressure Nitrogen gas charge
allows for quicker damping
response time.
1.97-Inch (50mm) Monotube body
provides improved heat dissipation
over other twin-tube shocks.
Application specific deflective
disc valving instantly senses and
automatically responds to any
suspension input to deliver precise
control, superb ride, and predictable handling characteristics.
**
For more information visit gorancho.com
S.19
RS9000™XL SHOCK ABSORBER
NINE LEVELS OF PERFORMANCE
2.75-in. (70mm) BODY DIAMETER*
Delivers both performance and appearance
9-POSITION TUNING TECHNOLOGY
Provides 9 different levels of shock performance
Rancho® RS9000™XL 9-position Adjustable Shocks deliver an exclusive nine levels of performance to stock or lifted off-road
trucks, SUVs and Jeeps. Globally recognized as the first 9-position manually adjustable Shocks series in the off-road market, this
advanced line of Shocks is ideal for off-road use, towing, hauling and more. RS9000XL 9-position Shocks allow the driver to control
how soft or firm the ride quality is through the Shock’s manual dampening and provide up to 400-percent change in vehicle control
and response from setting one to nine.
Plus, the RS9000XL Series Shocks come housed in an extra-large shock body, allowing for cooler and more consistent performance
under even the most demanding conditions. Covered by a Limited Lifetime Warranty and 90-Day Free-Ride Offer**.
Rancho RS9000XL 9-position Adjustable Shocks deliver an exclusive
nine levels of performance to stock or lifted off-road trucks, SUVs and
Jeeps. Globally recognized as the first 9-position manually adjustable
shocks series in the off-road market, this advanced line of shocks is
ideal for off-road use, towing, hauling and more. RS9000XL 9-position
shocks allow the driver to control how soft or firm the ride quality is
through the shock’s manual dampening and provide up to 400-percent
change in vehicle control and response from setting one to nine. Plus,
the RS9000XL series shocks come housed in an extra-large shock
body, allowing for cooler and more consistent performance under even
the most demanding conditions.
S.20
9-Position adjustment knob
provides user specific tuning.
Graphite filled Fluon banded piston
for increased durability.
Nitrogen Gas charged for
demanding off-road conditions.
A high strength polyurethane
Heavy-Duty 18mm diameter Nibumper that helps control the retro-Carburized rod.
bound motion of the Shock in harsh
driving conditions.
Premium long lasting Liquid
Metallic finish.
Double welded loops with Polyurethane bushings for enhanced
performance and durability.
Sintered Iron piston for long service
life.
Low-Friction self-lubricating seal
retains gas and oil.
Red boot provides protection for
rod and seal.
Tri-Tube, Mono-Flow design ensures exceptional performance.
THE ULTIMATE SHOCK
CHOICE FOR VERSATILITY
2.75-in. (70mm) body diameter*
allows more fluid carrying capacity
for a cooler running shock.
Tri-Tube, Mono-Flow design
ensures exceptional performance.
*
Select Applications. **For more information visit gorancho.com
S.21
YEAR
RS5000™ STEERING STABILIZER
Rancho® RS5000™ Steering Stabilizers are a simple and affordable way to enhance a vehicle’s performance. Rancho Steering
Stabilizers are ideal for off-road driving, towing and street applications. The Steering Stabilizers reduce wheel shimmy, bump steer
and vibration as the Shock Series was engineered for vehicles with oversized tires and wheels. Steering Stabilizers can help reduce
on or off-road driver fatigue. Rancho Steering Stabilizers are built from the foundation of the RS5000 Series Shock Absorber –
the world’s best-selling shock! Covered by a Limited Lifetime Warranty**.
MODEL
Engineered for vehicles with
oversized wheels & tires.
Available in single and dual
configurations.
Reduce wheel shimmy,
bump steer and vibration.
Bracket kits available for
vehicles without OE mounts.
Each Rancho RS5000X series
shock includes a red polyvinyl
accordion protection boot,
adding protection to the shock
rod and oil seal during on- and
off-road driving.
BRACKET KIT
Wrangler JK
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS5418
-
09-07
Wrangler JK
Single Steering Stabilizer - O.E. mounting location
RS5407
RS55103
17-07
Wrangler JK
HIGH-CLEARANCE STEERING STABILIZER KIT1
RS5401
RS64100
17-07
Wrangler JK
Dual Steering Stabilizer setup
06-97
Wrangler TJ/LJ
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS5407
-
06-97
Wrangler TJ/LJ
Optional Steering Stabilizer
4
RS5401
-
01-84
Cherokee XJ
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS5401
-
96-86
Wrangler YJ
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS5407
-
86-46
Wrangler CJ
Steering Stabilizer Kit
RS97345
-
86-46
Wrangler CJ
Single Steering Stabilizer
RS5402
RS5508
04-99
Grand Cherokee WJ
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS5409
-
98-93
Grand Cherokee ZJ
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS5401
-
RS5405
2
MODEL
RS64101
Q2
DESCRIPTION
PART
NUMBER
BRACKET
KIT
07-02
Avalanche 2500 2/4WD
Single Steering Stabilizer - O.E. mounting location
RS5407
RS5548
07-05
Silv./Sierra 1500HD 4WD Crew Cab
Single Steering Stabilizer - O.E. mounting location
RS5407
RS5548
03-01
Silv./Sierra 1500HD 2/4WD Crew Cab
Single Steering Stabilizer - O.E. mounting location
RS5407
RS5548
08-05
Silv./Sierra 1500HD 2WD Crew
Cab Classic
Single Steering Stabilizer - O.E. mounting location
RS5407
RS5548
15-11
Silv./Sierra 2500HD 4WD
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS5417
-
10-01
Silv./Sierra 2500HD 4WD (9200 GVW)
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS5411
-
08-01
Silv./Sierra 2500HD 2/4WD (9200 GVW)
Single Steering Stabilizer - O.E. mounting location
RS5407
RS5548
04-99
Silv./Sierra 2500 4WD
(Up to 8600 GVW)
Single Steering Stabilizer - O.E. mounting location
RS5407
RS5548
02-00
Suburban 2500 4WD (Up to 8600 GVW)
Single Steering Stabilizer - O.E. mounting location
RS5407
RS5548
06-00
Yukon XL 2500 4WD (Up to 8600 GVW)
Single Steering Stabilizer - O.E. mounting location
RS5407
RS5548
RS5416
RS64450
08-06
01-00
2014
12-03
12-09
08-00
Ram 1500 4WD Mega Cab Exc. IFS Models
Ram 1500 4WD w/ OEM number
52106909AB, AC & AD
Ram 2500 4WD Diesel
Ram 2500 4WD - Inc. Mega Cab, Power
Wagon & Regular/Standard Cab Models
Ram 2500 and 3500 4WD part numbers
52122370AB & 5154661AA
Ram 2500 and 3500 4WD w/ OEM
number 52106909AB, AC & AD
Dual Steering Stabilizers
Q2
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS5412
-
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS5410
-
RS5416Q2
RS64450
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS5416
-
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS5412
-
Dual Steering Stabilizers
02-97
Expedition 4WD
Single Steering Stabilizer - O.E. mounting location
RS5401
RS5567
1997
Expedition 2WD
Single Steering Stabilizer - O.E. mounting location
RS5401
RS5567
2004
F150 Heritage Series (Old body style)
w/ Rancho RS6488
Single Steering Stabilizer - O.E. mounting location
RS5401
RS5567
17-08
F250 and F350 4WD w/ Rancho Lift Kit
Dual Steering Stabilizers
RS5405
RS64551
15-08
F250 and F350 4WD
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
07-05
F250 and F350 4WD w/ Rancho
RS6510 or RS6511
Dual Steering Stabilizers
13-08
F450 and F550 2/4WD
09-03
Hummer H2
Q2
RS5415
-
RS5405Q2
RS64551
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS5415
-
Single Steering Stabilizer - O.E. mounting location
RS5407
RS5548
The installation of this kit requires at least 2-in. tall front bump stop spacers. This prevents the Steering Stabilizer from hitting the bottom of the frame at full jounce
travel. 2 Requires a 2-in. minimum lift to use, Stabilizer protective boots cannot be used. 3The installation of this kit requires a 2-in lift minimum with at least 2-in
tall front bump stop spacers. This prevents the steering stabilizer from contacting other components at full jounce travel. 4Part No. RS5401. Single large cylinder
S.23
Steering Stabilizer. Q2 Quantity two required. **For more information visit gorancho.com
1
S.22
PART NUMBER
17-10
YEAR
Twin tube cellular gas design
with 1 3/8-in piston.
DESCRIPTION
YEAR
RS7000 MT STEERING STABILIZER
®
MONOTUBE DESIGN
Rancho® RS7000®MT Monotube Steering Stabilizers enhance a vehicle’s performance, and are ideal for off roading, towing and
street applications. Utilizing Monotube Technology, Rancho Steering Stabilizers help reduce wheel shimmy, bump steer, and vibration while tightening up steering performance by damping the tie rod to the axle. The Shock was engineered for Jeeps and trucks
running oversized tires and wheels. RS7000MT Steering Stabilizers, built from the foundation of the Rancho RS7000MT Series
Shock, can help reduce on- and off-road driver fatigue. The series is covered by a Limited Lifetime Warranty**.
MODEL
Monotube design with high
pressure Nitrogen gas charge
allows for quicker damping
response time.
1.97-Inch (50mm) Monotube body
provides improved heat dissipation
over other twin-tube shocks.
Ten-stage velocity sensitive valving
provides tuning specific for each
vehicle.
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS7418
-
09-07
Wrangler JK
Single Steering Stabilizer - O.E. mounting location
RS7407
RS55103
17-07
Wrangler JK
HIGH-CLEARANCE STEERING STABILIZER KIT1
RS7401
RS64100
17-07
Wrangler JK
Dual Steering Stabilizer setup
06-97
Wrangler TJ/LJ
Single Steering Stabilizer - Bolts to O.E. mounts - Inc. Rubicon &Unlimited
RS7407
-
01-84
Cherokee XJ
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS7401
-
96-86
Wrangler YJ
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS7407
-
98-93
Grand Cherokee ZJ
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS7401
-
S.24
BRACKET
KIT
Single Steering Stabilizer - O.E. mounting location
RS7407
RS5548
Single Steering Stabilizer - O.E. mounting location
RS7407
RS5548
03-01
Silv./Sierra 1500HD 2/4WD Crew Cab
Single Steering Stabilizer - O.E. mounting location
RS7407
RS5548
08-05
Silv./Sierra 1500HD 2WD Crew
Cab Classic
Single Steering Stabilizer - O.E. mounting location
RS7407
RS5548
10-01
Silv./Sierra 2500HD 4WD (9200 GVW)
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS7411
-
08-01
Silv./Sierra 2500HD 2/4WD (9200 GVW)
Single Steering Stabilizer - O.E. mounting location
RS7407
RS5548
04-99
Silv./Sierra 2500 4WD
(Up to 8600 GVW)
Single Steering Stabilizer - O.E. mounting location
RS7407
RS5548
02-00
Suburban 2500 4WD (Up to 8600 GVW)
Single Steering Stabilizer - O.E. mounting location
RS7407
RS5548
06-00
Yukon XL 2500 4WD (Up to 8600 GVW)
Single Steering Stabilizer - O.E. mounting location
RS7407
RS5548
RS7416Q2
RS64450
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS7412
-
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS7410
-
RS7416Q2
RS64450
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS7416
-
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS7412
-
08-00
1
PART
NUMBER
Silv./Sierra 1500HD 4WD Crew Cab
12-09
Bracket kits available for
vehicles without OE mounts.
DESCRIPTION
Avalanche 2500 2/4WD
12-03
46mm Bore Monotube construction
- Ideal for larger light trucks, SUVs
and more.
MODEL
RS64101
Q2
07-05
2014
Full-floating dividing piston and
high pressure Nitrogen gas maintains constant pressure against the
hydraulic oil, eliminating possible
aeration and shock fade.
RS7405
2
07-02
01-00
Available in single and dual configurations.
BRACKET KIT
Wrangler JK
08-06
14mm hardened Steel piston rod
for superior strength over standard
11mm rods.
PART NUMBER
17-10
YEAR
Huge 46mm working piston with
Fluon band for consistent sealing
between the piston and monotube
which delivers better control
and increased durability compared
to conventional piston designs.
DESCRIPTION
Ram 1500 4WD Mega Cab Exc. IFS Models
Ram 1500 4WD w/ OEM number
52106909AB, AC & AD
Ram 2500 4WD Diesel
Ram 2500 4WD - Inc. Mega Cab, Power
Wagon & Regular/Standard Cab Models
Ram 2500 and 3500 4WD part numbers
52122370AB & 5154661AA
Ram 2500 and 3500 4WD w/ OEM
number 52106909AB, AC & AD
Dual Steering Stabilizers
Dual Steering Stabilizers
02-97
Expedition 4WD
Single Steering Stabilizer - O.E. mounting location
RS7401
RS5567
1997
Expedition 2WD
Single Steering Stabilizer - O.E. mounting location
RS7401
RS5567
2004
F150 Heritage Series (Old body style)
w/ Rancho RS6488
Single Steering Stabilizer - O.E. mounting location
RS7401
RS5567
17-08
F250 and F350 4WD w/ Rancho Lift Kit
Dual Steering Stabilizers
RS7405Q2
RS64551
15-08
F250 and F350 4WD
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS7415
-
07-05
F250 and F350 4WD w/ Rancho
RS6510 or RS6511
Dual Steering Stabilizers
RS7405Q2
RS64551
13-08
F450 and F550 2/4WD
Single Steering Stabilizer - Bolts to O.E. mounts - no bracket required
RS7415
-
09-03
Hummer H2
Single Steering Stabilizer - O.E. mounting location
RS7407
RS5548
The installation of this kit requires at least 2-in. tall front bump stop spacers. This prevents the Steering Stabilizer from hitting the bottom of the frame at full jounce
travel. 2 Requires a 2-in. minimum lift to use, Stabilizer protective boots cannot be used. 3The installation of this kit requires a 2-in lift minimum with at least 2-in tall
front bump stop spacers. This prevents the steering stabilizer from contacting other components at full jounce travel. Q2 Quantity two required.
**For more information visit gorancho.com
S.25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement