United States Stove 3000 User's Manual
Add to my manuals24 Pages
United States Stove 3000 is a wood burning stove that is certified for use in the USA and Canada. It is a safety-tested appliance that meets the UL 1482-2010 and ULC-S627-2000 standards. The stove is also US Environmental Protection Agency Phase II certified, and it is approved for use in Washington State. The stove has a maximum log length of 21 inches, and it can heat up to 3.11 cubic feet of space. It is a durable and efficient stove that is built to last.
advertisement
Owner’s Operation and Instruction Manual
MODEL: 3000 (L), (LN)
CERTIFIED FOR USA and CANADA
SAFETY TESTED TO UL 1482-2010 and ULC-S627-2000
US ENVIRONMENTAL PROTECTION AGENCY PHASE II CERTIFIED WOODSTOVE
WASHINGTON STATE APPROVED
CAUTION!
Please read this entire manual before you install or use your new room heater. Failure to follow instructions may result in property damage, bodily injury, or even death.
Improper Installation Could Void
Your Warranty!
SAVE THESE INSTRUCTIONS
THIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLE YOU TO OR-
DER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
UN
ITE U
D STATES STOV
S S
COMPANY
C E
United States Stove Company
227 Industrial Park Road
P.O. Box 151
South Pittsburg, TN 37380
851879 rev C
CONGRATULATIONS!
You’ve purchased a heater from North America’s oldest manufacturer of wood burning products.
By heating with wood you’re helping to CONSERVE ENERGY!
Wood is our only Renewable Energy Resource. Please do your part to preserve our wood supply. Plant at least one tree each year.
Future generations will thank you.
Combustible :
Colors :
Flue Pipe Diameter :
Flue Pipe Type: (Standard Single Wall):
Minimum Chimney Height :
Maximum Log Length :
Dimensions
Overall :
Depth x Width x Height :
Combustion Chamber :
Width x Depth :
Volume : Cubic Feet:
Door Opening : Width x Height:
Pyroceramic Glass Door : (Viewing) Width x Height:
Weight (lbs):
Wood
Metallic Black
6” (152.5mm)
Black or Blued Steel 2100°F (650°C)
12’ (3.7m)
21” (533.5mm)
29 1/2 ” x 27” x 28 5/8” (749mm x 686mm x 727mm)
22 3/4” x 21 ” (578mm x 533mm)
3.11 ft ³ (.0881m³)
16” x 8” (406.5mm x 203mm)
13
13
/16
” x 8 3/8” (351mm x 213mm)
375 lbs (170kg)
2
CAUTIONS:
• HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY.
CONTACT MAY CAUSE SKIN BURNS.
• DO NOT USE CHEMICALS OR FLUIDS TO IGNITE THE FIRE.
• DO NOT LEAVE THE STOVE UNATTENDED WHEN THE DOOR IS SLIGHTLY OPENED.
• DO NOT BURN GARBAGE, FLAMMABLE FLUID SUCH AS GASOLINE, NAPHTHA OR
MOTOR OIL.
• DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.
• ALWAYS CLOSE THE DOOR AFTER THE IGNITION.
Ussc
WARRANTY INFORMATION CARD
Name__________________________________________ Telephone #: (_____)_____________
City____________________________________________ State_______ Zip_________________
Email Address __________________________________________________________________
Model # of Unit________________________________ Serial #___________________________
Fuel Type: Wood Coal Pellet Gas Other _________________________
Place of Purchase (Retailer)______________________________________________________
City____________________________________________ State_______ Zip_________________
If internet purchase, please list website address___________________________________
Date of Purchase _______________________________________________________________
Reason for Purchase: Alternative Heat
Decoration Cost
Main Heat Source
Other _________________________
What was the determining factor for purchasing your new appliance?_______
I have read the owner’s manual that accompanies this unit and fully understand the: of my new appliance.
Ussc
Print Name Signature Date
Please attach a copy of your purchase receipt.
Warranty not valid without a Proof of Purchase.
Warranty information must be received within 30 days of original purchase.
Detach this page from this manual, fold in half with this page to the inside and tape together. Apply a stamp and mail to the address provided. You may use an envelope if you choose.
You may register online by going to www.usstove.com
All information submitted will be kept strictly confi dential. Information provided will not be sold for advertising purposes.
Contact information will be used solely for the purpose of product notifi cations.
3
4
Fold Here
PLACE
STAMP
HERE
United States Stove Company
P.O. Box 151
South Pittsburg, TN 37380
Ussc
Tools and Materials Needed For Installation
You will need a drill with a 1/8” bit to install sheet metal screws into connector pipe. A 5/16” socket/wrench or screw driver to install pedestal trim, room air defl ector, and blower assembly described below. A 1/2” socket/wrench to install fl ue collar. A non-combustible fl oor protector as specifi ed in this manual. All chimney and chimney connector components required for your particular chimney installation.
for more details.
Assembly
Flue Collar Assembly:
1. Mount the fl ue collar to the top of the unit as shown using the (3) 5/16-18 x 1-1/2 bolts, (3) washers, and (3) weld tabs provided in the parts box.
Room Air Defl ector Assembly:
1. Locate the Room Air Defl ector. Using the three(3) 1/2 Tek Screws provided, mount the defl ector to the unit as shown in the diagram.
Firebrick Confi guration:
1. Replace the Firebrick as shown in the illustration below.
Side view of fl ue collar mount to heater top
5/16-18 x 1-1/2
BOLT
HEATER
TOP
WELD
TAB
Brick Confi guration
Ussc 5
ASSEMBLY INSTRUCTIONS
Blower Assembly
THE BLOWER ASSEMBLY MUST BE DISCONNECTED
FROM THE SOURCE OF ELECTRICAL SUPPLY BE-
FORE ATTEMPTING THE INSTALLATION.
THE BLOWER ASSEMBLY IS INTENDED FOR USE
ONLY WITH A STOVE THAT IS MARKED TO INDICATE
SUCH USE.
DO NOT ROUTE THE SUPPLY CORD NEAR OR
ACROSS HOT SURFACES!
Fix the assembly to the back of the stove with the four screws provided.
Pedestal Trim Assembly
Attach to the pedestal base at the location shown using the screws provided.
Leg Assembly
If not already installed or for purpose of repair, follow these directions. Because of this heaters weight, we suggest getting assistance maneuvering it into position.
Begin by removing all the fi rebrick. Carefully roll the heater onto its side, placing a couple wooden blocks to hold the heater off the legs. A piece of carpet would also help reduce the chances of scratching the unit. Once you’ve attached the legs with the supplied hardware, stand the heater back on its legs.
Ash Pan Assembly
If not already installed, slide the ash pan inside the ash pan housing.
6
2 BOLTS PER LEG
Ussc
INSTALLATION
SAFETY NOTICE
• IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. TO REDUCE THE
RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS.
• THIS STOVE IS NOT APPROVED FOR INSTALLATION IN A MANUFACTURED OR MOBILE
HOME.
• CONSULT YOUR MUNICIPAL BUILDING DEPARTMENT OR FIRE OFFICIALS ABOUT PERMITS,
RESTRICTIONS AND INSTALLATIONS REQUIREMENTS IN YOUR AREA.
• USE SMOKE DETECTORS IN THE ROOM WHERE YOUR STOVE IS INSTALLED.
• KEEP FURNITURE AND DRAPES WELL AWAY FROM THE STOVE.
• NEVER USE GASOLINE, GASOLINE-TYPE LANTERN FUEL, KEROSENE, CHARCOAL LIGHTER
FLUID, OR SIMILAR LIQUIDS TO START OR “FRESHEN UP” A FIRE IN THIS HEATER. KEEP ALL
SUCH LIQUIDS WELL AWAY FROM THE HEATER WHILE IT IS IN USE.
• IN THE EVENT OF A CHIMNEY FIRE, PUSH THE AIR CONTROL FULL CLOSED TO DEPRIVE
THE FIRE OF OXYGEN. CALL THE FIRE DEPARTMENT.
• DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.
• A SOURCE OF FRESH AIR INTO THE ROOM OR SPACE HEATED SHALL BE PROVIDED WHEN
REQUIRED.
POSITIONING THE STOVE
It is very important to position the wood stove as close as possible to the chimney, and in an area that will favor room where the most time is spent, and in the most spacious room possible. Recall that wood stoves produce radiating heat, the heat we feel when we are close to a wood stove. A wood stove also functions by convection, that is through the displacement of hot air accelerated upwards and its replacement with cooler air. If necessary, the hot air distribution from the stove may be facilitated by the installation of a blower.
may occur.
A wood stove must never be installed in a hallway or near a staircase, since it may block the way in case of fi re or fail to respect required clearances.
Ussc 7
FLOOR PROTECTOR
Your wood stove should be placed on a 1 inch, non-combustible surface with a k factor of 0.84. For multiple there is a horizontal section of chimney connector, the fl oor protector should go under it and 2 inches beyond each side of the chimney connector.
Convert specifi cation to R-value: k-factor is given with a required thickness (T) in inches: R=1/k x T
C-factor is given: R=1/C
Example:
If the fl oor protector is 4” brick with a C-factor of 1.25 over 1/8” mineral board with a “k” factor of 0.29 the total R-value of the system is:
4” brick C=1.25, R=1/1.25=0.8
1/8” mineral board K=0.29, R=1/0.29 x 0.125=0.431
Total R = Rbrick + Rmineral = 0.8 + 0.431 = 1.231
Total R is greater than 1.2, the system is acceptable.
Model
3000
Front
26”
(660mm)
Sides
8”
(203mm)
Rear
6”
(152mm)
- Canadian installations require 8” (203mm)
8 Ussc
CLEARANCES TO COMBUSTIBLES
It is of utmost importance that the clearances to combustible materials be strictly adhered to during installation of the stove. Refer to the tables below :
Model A
3000 14
(358mm)
B
20
(508mm)
Single Wall Pipe
C D
17.5
(445mm)
30.5
(775mm)
E
11
(279mm)
F
24
(610mm)
• Floor to ceiling height must be at least 7’ (2.13m) in all cases.
• Do not place any combustible material within 4’ (1.2m) of the front of the unit.
fl oor, or a ceiling.
• For Canadian installations, where passage through a wall, or partition of combustible construction is desired, the installation must conform to CAN/CSA-B365.
• A fl ue pipe crossing a combustible wall must have a minimum clearance of 18” (457.2mm).
• To reduce clearances from combustible materials, contact your local safety department.
Ussc 9
CHIMNEY CONNECTOR (STOVE PIPE)
Your chimney connector and chimney must have the same diameter as the stove outlet (6”). If this is not the case, we recommend you contact your dealer in order to insure there will be no problem with the draft .
It is strictly forbidden to use galvanized steel.
Your smoke pipe should be assembled in such a way that the male section (crimped end) of the pipe faces down.
Attach each of the sections to one another with three equidistant metal screws.
with the upper end of the section toward the chimney. Any installation with a horizontal run of chimney pipe must conform to NFPA 211. You may contact NFPA (National Fire Protection Association) and request the latest edition of the NFPA Standard 211 .
To insure a good draft , the total length of the coupling pipe should never exceed 8’ to 10’ (2.4m to 3.04 m).
(Except for cases of vertical installation, cathedral-roof style where the smoke exhaust system can be much longer and connected without problem to the chimney at the ceiling of the room).
Installation of a “barometric draft stabilizer” (fi replace register) on a smoke exhaust system is prohibited.
Furthermore, installation of a draft damper is not recommended. Indeed, with a controlled combustion wood stove, the draft is regulated upon intake of the combustion air in the stove and not at the exhaust.
10 Ussc
CHIMNEY
Your wood stove may be hooked up with a 6” factory built or masonry chimney. If you are using a factory built chimney, it must comply with UL 103 or CSA-B365 standard; therefore it must be a Type HT (2100°F). It is extremely important that it be installed according to the manufacturer’s specifi cations.
If you are using a masonry chimney, it is important that it be built in compliance with the specifi cations of the
National Building Code. It must be lined with fi re clay bricks, metal or clay tiles sealed together with fi re cemay cause draft problems, while a large fl ue favours rapid cooling of the gas, and hence the build-up of creosote and the risk of chimney fi res. Note that it is the chimney and not the stove which creates the draft eff ect; your stove’s performance is directly dependent on an adequate draft from your chimney.
1. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
2. It must rise above the roof at least 3’ (0.9m) from the uppermost point of contact.
height of 2’ (0.6m).
4. Installation of an interior chimney is always preferable to an exterior chimney. Indeed, the interior chimney will, by defi nition, be hotter than an exterior chimney, being heated up by the ambient air in the house. of chimney fi res.
6. Using a fi re screen at the extremity of the chimney requires regular inspection in order to insure that it is not obstructed thus blocking the draft , and it should be cleaned when used regularly.
Ussc 11
FACTORY BUILT CHIMNEY :
When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed.
You must also purchase (from the same manufacturer) and install the ceiling support package or wall passthrough and “T” section package, fi restops (where needed), insulation shield, roof fl ashing, chimney cap, etc. required height above the roof or other obstructions for safety and proper draft operation.
12 Ussc
MASONRY CHIMNEY :
Ensure that a masonry chimney meets the minimum standards of the National Fire Protection Association
(NFPA) by having it inspected by a professional. Make sure there are no cracks, loose mortar or other signs of deterioration and blockage. Have the chimney cleaned before the stove is installed and operated. When connecting the stove through a combustible wall to a masonry chimney, special methods are needed.
Ussc 13
Combustible Wall Chimney Connector Pass-Throughs
Method A. 12” (304.8 mm) Clearance to Combustible Wall Member: Using a minimum thickness 3.5” (89 mm) brick and a 5/8” (15.9 mm) miniliner must conform to ASTM C315 (Standard Specifi cation for Clay Fire
Linings) or its equivalent. Keep a minimum of 12” (304.8 mm) of brick run from the brick masonry outer surface to the inner surface of the chimney fl ue liner but not past the inner surface. Firmly grout or cement the clay liner in place to the chimney fl ue liner.
Method B. 9” (228.6 mm) Clearance to Combustible Wall Member: Using a 6” (152.4 mm) inside diameter, listed, factory-built Solid-Pak chimney section with insulation of 1” (25.4 mm) or more, build a wall pass-through with a minimum 9” (228.6 mm) air space between the outer wall of the chimney length and wall combustibles. Use sheet metal supports fastened securely to wall surfaces on all sides, to maintain the 9” (228.6 mm) air space. When fastening supports to chimney length, do not penetrate the the Solid-Pak chimney section shall be fl ush with the inside of the masonry chimney fl ue, and sealed with a non-water soluble refractory cement.
Use this cement to also seal to the brick masonry penetration.
Method C. 6” (152.4 mm) Clearance to Combustible Wall Member: Starting with a minimum 24 gage (.024” [.61 mm]) 6” (152.4 mm) metal chimney connector, and a minimum 24 gage ventilated wall thimble which has two air channels of 1” (25.4 mm) each, construct a wall pass-through. glass insulation, from the outer surface of the wall thimble to wall combustibles. Support the wall thimble, and cover its opening with a 24-gage should also be a support sized to fi t and hold the metal chimney connector. See that the supports are fastened securely to wall surfaces on all sides.
Make sure fasteners used to secure the metal chimney connector do not penetrate chimney fl ue liner.
Method D. 2” (50.8 mm) Clearance to Combustible Wall Member: Start with a solid-pak listed factory built chimney section at least 12” (304 mm) long, with insulation of 1” (25.4 mm) or more, and an inside diameter of
8” (2 inches [51 mm] larger than the 6” [152.4 mm] chimney connector).
Use this as a pass-through for a minimum 24-gauge single wall steel chimney connector. Keep solid-pak section concentric with and spaced 1” (25.4 mm) off the chimney connector by way of sheet metal support plates at both ends of chimney section. Cover opening with and support chimney section on both sides with 24 gage minimum sheet metal supports. See that the supports are fastened securely to wall surfaces on all sides. Make sure fasteners used to secure chimney fl ue line .
NOTES:
1. Connectors to a masonry chimney, excepting method B, shall extend in one continuous section through the wall passthrough system and the chimney wall, to but not past the inner fl ue liner face.
2. A chimney connector shall not pass through an attic or roof space, closet or similar concealed space, or a fl oor, or ceiling.
14 Ussc
OUTSIDE COMBUSTION AIR
Your wood stove is approved to be installed with an outside air intake which is necessary for a tightly constructed home and houses with a negative pressure problem. You can purchase this option through your heater dealer be the type with louvers, rodent grill only.
Outside combustion air may be required if :
1. Your stove does not draw steadily, smoke rollout occurs, wood burns poorly, or back-draft s occur whether or not there is combustion present.
2. Existing fuel-fi red equipment in the house, such as fi replaces or other heating appliances, smell, do not operate properly, suff er smoke roll-out when opened, or back-draft s occur whether or not there is combustion present.
3. Opening a window slightly on a calm (windless) day alleviates any of the above symptoms.
devices that exhaust house air.
6. A ventilation system is installed in the house.
Ussc 15
WOODSTOVE UTILIZATION
Your heating unit was designed to burn wood only; no other materials should be burned. Waste and other fl ammable materials should not be burned in your stove. Any type of wood may be used in your stove, but specifi c varieties have better energy yields than others. Please consult the following table in order to make the best possible choice.
TYPE
Hickory
WEIGHT
(LBS. CU. FT., DRY)
63
PER CORD
4500
EFFICIENCY
RANKING
1.0
SPLITS
Well
MILLIONS
BTU’s/CORD
31.5
White Oak 48 4100 .9
Fair 28.6
Red Oak
Beech
Sugar Maple
Black Oak
Ash
Yellow Birch
Red Maple
Paper Birch
Elm/Sycamore
Red Spruce
42
40
38
37
34
29
44
43
46
45
3600
3400
3200
3100
3900
3800
3700
3700
2900
1800
.5
.4
.3
.3
.2
.1
.6
.6
.8
.7
Well
Hard
Fair
Easy
Fair
Hard
Fair
Fair
Easy
25.0
23.8
22.6
22.1
27.4
26.8
26.2
25.6
20.1
16.1
such that the humidity content (in weight) is reduced below 20% of the weight of the log. It is very important to keep in mind that even if the wood has been cut for one, two or even more years, it is not necessarily dry, if it has been stored in poor conditions. Under can be:
- ignition problems
- creosote build-up causing chimney fi res
- low energy yield
- blackened windows
- incomplete log combustion the ground. Air should circulate through the cord. A 24” to 48” air space should be left between each row of logs, which should be
TESTING YOUR WOOD
When the stove is thoroughly warmed, place one piece of split wood (about fi ve inches in diameter) parallel to the door on the bed of red embers.
Keep the air control full open by pulling on it and close the door. If ignition of the piece is accomplished within 90 seconds from the time if was placed in the stove, your wood is correctly dried. If ignition takes longer, your wood is damp.
If your wood hisses and water or vapor escapes at the ends of the piece, your wood is soaked or freshly cut. Do not use this wood in your stove. Large amounts of creosote could be deposited in your chimney, creating potential conditions for a chimney fi re.
16 Ussc
THE FIRST FIRES in your stove for the fi rst four hours of operation. Never open the air control more than necessary to achieve a medium burn rate.
start your stove outside. You will not be able to see if you are over heating.
Do not build fi res too close to the glass. Try building behind the lip just inside the door opening.
IGNITION
Aft er making sure that the stove air intake controls are fully open (completely pull-out towards you), place several rumpled sheets of paper in the centre of the combustion chamber. Place 8 to 10 pieces of small dry kindling wood over the paper in the form of a tent.
You may also place a few pieces of heating wood, but choose the smaller ones. No chemical product should be used to light the fi re.
draft problems oft en due to negative pressure in the house. If such is the case, open a window slightly near the stove and twist together a few sheets of newspaper into a torch. Light up this paper torch and hold it as close as possible to the mouth of the pipe inside the combustion chamber to warm up the chimney. Once the updraft movement is initiated, you are ready to ignite the stove by lighting the paper and kindling wood inside the combustion chamber.
When you have achieved a good bed of hot embers, we recommend the following burn procedures:
HEATING
3000
Primary Air Settings
(Slide Damper is located in center of stove under hearth plate)
(Damper Adjustment: Pulling out on damper increases air)
Burn Rate
Low
Medium - Low
Medium - High
High
Adjust Damper from fully closed
1/8” (3.2mm)
1/4” (6.3mm)
1-1/8” (12.7mm) approx. 3” (76mm)
Electric Blower Speed Setting (Variable)
(Blower is on High when turned “ON”, Rotate clockwise until stop for “LOW”.)
Burn Time
@ 30 minutes
Blower Speed
Low
@ 30 minutes
@ 30 minutes all minutes
Low
Low
High
CAUTION: Never alter the damper slide or the adjustment range to increase fi ring for any reason. Doing so could result in heater damage and will void your warranty.
in the combustion chamber to a minimum. On the other hand, wood will burn quickly if the air control is adjusted to admit a larger towards you, it is fully open. If you push on it until it stops the combustion air is reduced to a minimum. Real operating conditions may give very diff erent results than those obtained during testing according to the species of wood used, its moisture content, the size and density of the pieces, the length of the chimney, altitude and outside temperature.
Ussc 17
WARNINGS
• NEVER OVERFIRE YOUR STOVE. IF ANY PART OF THE STOVE STARTS TO GLOW RED, OVER
FIRING IS HAPPENING. READJUST THE AIR INTAKE CONTROL AT A LOWER SETTING.
• THE INSTALLATION OF A LOG CRADLE or GRATES IS NOT RECOMMENDED IN YOUR WOOD
STOVE. BUILD FIRE DIRECTLY ON FIREBRICK.
• NEVER PUT WOOD ABOVE THE FIREBRICK LINING OF THE FIREBOX.
RELOADING
Once you have obtained a good bed of embers, you should reload the unit. In order to do so, open the air slowly; open it one or two inches for 5 to 10 seconds, before opening it completely to increase the draft and thus the front of the stove and reload the unit.
For optimal operation of your wood stove, we recommend you to operate it with a wood load approximately equivalent to the height of fi re bricks.
It is important to note that wood combustion consumes ambient oxygen in the room .In the case of negative pressure, it is a good idea to allow fresh air in the room, either by opening a window slightly or by installing a fresh air intake system on an outside wall.
Creosote - Formation and Need for Removal - When wood is burned slowly, it produces tar and other organic cool chimney fl ue of a slow-burning fi re. As a result, creosote residue accumulates on the fl ue lining. When at least once every two months during the heating season to determine if a creosote build-up has occurred. If creosote has accumulated (3mm or more), it should be removed to reduce the risk of a chimney fi re.
We strongly recommend that you install a magnetic thermometer on your smoke exhaust pipe, approximately these temperatures, the build-up of creosote is promoted. Above 500 degrees, heat is wasted since a too large quantity is lost into the atmosphere.
TO PREVENT CREOSOTE BUILD UP deposit.
• Leave the air control full open for about 5 min. every time you reload the stove to bring it back to proper
• Always check for creosote deposit once every two months and have your chimney cleaned at least once a year.
If a chimney or creosote fi re occurs, close all dampers immediately. Wait for the fi re to go out and the heater to cool, then inspect the chimney for damage. If no damage results, perform a chimney cleaning to ensure there is no more creosote deposits remaining in the chimney.
18 Ussc
ASH DISPOSAL
Ashes should be removed from the stove every few days or when ashes get to 2 to 3 inches deep. Always empty the stove when it is cold, such as in the morning. Ashes should be placed in a metal container with a tight fi tting from all combustible materials, pending fi nal disposal. If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the close container until all cinders have thoroughly cooled. Other waste shall not be placed in this container.
MAINTENANCE
a visual inspection of the stove every time it is emptied, in order to insure that no parts have been damaged, in which case repairs must be performed immediately. Inspect and clean the chimney and connector pipe periodically for creosote buildup or obstructions.
GLASS
• Inspect and clean the glass regularly in order to detect any cracks. If you spot one, allow the fi re to go out and the stove to cool before repairing. Never wash the glass with a product that may scratch the glass. Use a the heater is cold.
• Do not abuse the glass door by striking or slamming shut. Do not use the stove if the glass is broken. If the glass on your stove breaks, replace only with the glass supplied from your heater dealer. Never substitute other materials for the glass.
• To replace the glass, remove the screws retaining the glass mouldings inside the door. Remove the mouldings and replace the damaged piece with a new one. Perform the procedure backwards aft er replacing. When replacing the glass, you should change the glass gasket to make sure you keep it sealed.
GASKETING
It is recommended that you change the door gasket (which makes your stove door air tight) once a year, in orsimply remove the damaged one. Carefully clean the available gasket groove, apply a high temperature silicone sold for this purpose, and install the new gasket. You may light up your stove again approximately 24 hours aft er having completed this operation.
WARNING:
• NEVER OPERATE THE STOVE WITHOUT A GASKET OR WITH A BROKEN ONE. DAMAGE TO THE
STOVE OR EVEN HOUSE FIRE MAY RESULT.
PAINT
Only clean your stove with a dry soft cloth that will not harm the paint fi nish. If the paint becomes scratched or damaged, it is possible to give your wood stove a brand new look, by repainting it with a 1200° F heat resistant paint. For this purpose, simply scrub the surface to be repainted with fi ne sand paper, clean it properly, and apply thin coats (2) of paint successively.
BLOWER
The blower needs to be removed and air blown clean. Make sure the blades do not have build up.
Ussc 19
20
REPAIR PARTS
19
20
17 18
16
21
36
15
14
13
33
28
2
3
4
12
31
30
5 6 7
32
10
29
27
34
35
Feed Door Assembly
5
6
7
8
1
24 26 25 22 23
3
11
10
1
11
8
9
4
9
2
Ussc
REPAIR PARTS
10
11
12
13
6
7
8
9
3
4
5
1
2
14
15
16
17
18
19
20
21
22
69516 Feed Door Assy.
25080B Feed Door Latch
83508 5/16-18 x 3/4 Hex Head Bolt
83338 5/16-18 Lock Nut
891373 Door Hinge Pad
83045A Washer, 3/8” ID x 7/8” OD
83274 3/8-16 Lock Nut
86643 Tube, Secondary Air (Ø0.16 holes)
86645 Tube, Secondary Air (Ø0.22 holes)
25843 Retainer, Tube (1 per Secondary Tube) 3 - 5
88145 Refractory Insulation 1
891929 Damper Rod
891331 Spring Handle - Small
1
1
2
2
1
2
1
1
2
1
1
25826 Hearth Plate
25844 Shield, Rear
25845 Air Defl ector
40292A Flue Collar
88042 Flue Collar Gasket
83432 5/16-18 x 1-1/2 Hex Head Bolt
83045 Washer, 5/16” ID x 3/4” OD
83431 Weld Tab
89066 Firebrick (4.5 x 9 x 1.25)
1
1
1
1
1.7 Ft
3
3
3
23
23
24
25
26
27
891414 Firebrick (2-1/4 x 9)
24103 Firebrick (4-1/2 x 4-1/2)
891783 Firebrick (3 x 4-1/2 )
40561 Ash Plug
25855 Pedestal Front
32
33
34
35
28
29
30
31
25857
25856
25854
25846
25853
69773
891137
69778
Pedestal, Left Side
Pedestal, Right Side
Pedestal Bottom
Pedestal Back
Pedestal Brace
Ash Pan
Handle
Trim, One Piece
36 891492 B36 Blower Assembly
N/S = Not Shown
Key Part No.
9
10
11
6
7
8
3
4
5
1
2
25491
25692
83506
891135
88066
88087
891131
25464
25465
83202
83278
Description
Feed Door, Painted (40484)
Handle, Painted (40515)
3/8 x 1-1/4 Roll Pin
Spring Handle - LG
Rope Gasket - 5/8”
Glass Gasket - 1/8 thk x 1” wide
Ceramic Glass
Top Glass Retainer
Bottom Glass Retainer
10-24 x 3/8 Pan Head Phillips Screw
Washer - 7/32 ID x 1/2 OD
Qty.
1
1
1
1
4.6 Ft
3.7 Ft
1
1
1
4
4
Key Part No.
N/S
40566
83339
For Models with Legs
Description
Leg, Cast Iron
Bolt, 1/4-20 x 3/4
Qty.
2
8
IN ORDER TO MAINTAIN WARRANTY,
COMPONENTS MUST BE REPLACED USING
ORIGINAL MANUFACTURERS PARTS
PURCHASED THROUGH YOUR DEALER
OR DIRECTLY FROM THE APPLIANCE
MANUFACTURER.
USE OF THIRD PARTY COMPONENTS WILL
VOID THE WARRANTY.
1
1
1
2
1
1
1
1
1
1
1
1
1
1
Ussc 21
NOTES
22 Ussc
NOTES
Ussc 23
HOW TO ORDER REPAIR PARTS
THIS MANUAL WILL HELP YOU OBTAIN EFFICIENT, DEPENDABLE SERVICE
FROM YOUR HEATER, AND ENABLE YOU TO ORDER REPAIR PARTS CORRECTLY.
KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE.
WHEN WRITING, ALWAYS GIVE THE FULL MODEL NUMBER WHICH IS ON THE
NAMEPLATE ATTACHED TO THE HEATER.
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMA-
TION AS SHOWN IN THIS LIST:
1. THE PART NUMBER
2. THE PART DESCRIPTION
3. THE MODEL NUMBER: ___________________________
4. THE SERIAL NUMBER: ____________________________
24
UNITED STATES STOVE COMPANY
227 INDUSTRIAL PARK ROAD
P.O. BOX 151
SOUTH PITTSBURG, TN 37380
(423) 837-2100
WWW.USSTOVE.COM
Ussc
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project