Universal Remote Control 80-FAP Operating instructions

Add to My manuals
6 Pages

advertisement

Universal Remote Control 80-FAP Operating instructions | Manualzz

OPERATING INSTRUCTIONS

National-Riverside

MODELS 150-FAST

PROPANE

CONSTRUCTION

HEATER

FORCED AIR

150,000 BTU/HR

SPC

ALL-PRO

MODEL SPC-150T

HEATER SPECIFICATIONS - 150

Type of Gas

Input Rating

Fuel Consumption

Gas Supply Pressure

to Regulator

For Use with Propane Gas Only

150,000 BTU/hr

7 Lbs/hr

Regulator Out

Fuel Orifice Size

Electrical Input

Minimum Operating Voltage

Fan

Average Air Temp Rise

Ignition

Primary Flame Control

Max: Bottle Pressure

Min: 5 psig

11" W.C.

1.00 mm Drill - 18 Holes

115V, 60Hz 10, 4a

100V

3000 rpm, 450 cfm

Approx. 300 o F

Direct Spark, Interrupted Type

Solid State, 10-15 second Timing

High Temperature Limit Control 240 o F

Minimum Ambient Temp. Rating 0 o F

Size (Length x Width x Height)

New Weight

Shipping Weight

26" x 9" x 16"

32 lbs.

34 lbs.

!

YOUR SAFETY IS IMPORTANT TO YOU AND TO OTHERS,

SO PLEASE READ THESE INSTRUCTIONS BEFORE YOU

OPERATE THIS HEATER.

!

GENERAL HAZARD WARNING:

FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS PROVIDED WITH THIS

HEATER, CAN RESULT IN DEATH, SERIOUS BODILY INJURY AND PROPERTY LOSS OR DAMAGE

FROM HAZARDS OF FIRE, EXPLOSION, BURN, ASPHYXIATION, CARBON MONOXIDE POISONING,

AND/OR ELECTRICAL SHOCK.

ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUCTIONS SHOULD USE OR

SERVICE THIS HEATER.

IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS MANUAL,

LABELS, ETC. CONTACT THE MANUFACTURER.

RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

OPERATING PRECAUTIONS

This is a propane, direct-fired, forced air heater. It's intended use is primarily temporary heating of buildings under construction, alteration or repair.

!

WARNING

NOT FOR HOME OR RECREATIONAL VEHICLE USE

Propane is heavier than air. If propane leaks from a connection or fitting, it sinks to the floor, collecting there with the surrounding air, forming a potentially explosive mixture. Obviously, propane leaks should be avoided, so set up the propane supply with utmost care. Leak check new connections or reconnections with a soap and water solution and follow all connection instructions herein. Also, ask your propane dealer for advice on the propane supply installation and ask him to check it if there are any questions.

Direct-Fired means that all of the combustion products enter the heated space. Even though this heater operates very close to 100 percent combustion efficiecy, it still produces small amounts of carbon monoxide. Carbon monoxide (called

CO) is toxic. We can tolerate small amounts but not a lot. CO can build up in a heated space and failure to provide adequate ventilation could result in death. The symptoms of inadequate ventilation are: headache dizziness burning eyes and nose nausea dry mouth or sore throat

So, be sure to follow advice about ventilation in these operating instructions.

Forced Air means that a blower or fan pushes the air through the heater. Proper combustion depends upon this air flow; therefore, the heater must not be revised, modified or operated with parts removed or missing. Likewise, safety systems must not be circumvented or modified in order to operate the heater.

When the heater is to be operated in the presence of other people the user is responsible for properly acquainting those present with the safety precautions and instructions, and of the hazards involved.

SAFETY PRECAUTIONS

1.

2.

3.

4.

5.

6.

7.

Check the heater thoroughly for damage. DO NOT operate a damaged heater.

DO NOT modify the heater or operate a heater which has been modified from its original condition.

Use only propane gas.

Use only VAPOR WITHDRAWAL propane supply. If there is any question about vapor withdrawal, ask your propane dealer.

Mount the propane cylinders vertically (shutoff valve up). Secure them from falling or being knocked over and protect them from damage.

Locate propane containers at least 7 ft. from the heater and do not direct exhaust toward containers.

Use only the hose and regulator assembly provided with the heater. Inspect hose assembly before each use of the heater. If there is excessive abrasion or wear, or hose is cut, replace with hose assembly listed on parts list before using heater.

8.

9.

For indoor use only. Area must be well ventilated.

Provide minimum openings of 2 sq. ft. near the floor and 2 sq. ft. near the ceiling (also see "Operating

Precautions").

If at any time gas odor is detected, IMMEDIATELY

DISCONTINUE operation until the source of gas has been located and corrected.

10.

Install the heater such that it is not directly exposed to water spray, rain and/or dripping water.

11.

Maintain minimum clearance from normal combustible material (like paper) as follows: floor-0 ft.;outlet-6 ft.; sides-1 ft.; top-3 ft. Locate 10 ft.

from canvas or plastic tarpaulins or similar coverings and secure them to prevent flapping or movement due to wind action.

12.

Operate only on a stable, level surface.

13.

Do not use with ductwork. Do not restrict inlet or exit.

14.

Use only the electrical power specified. The electrical connection and grounding must comply with

National Electrical Code - ANSI/NFPA 70.

15.

Use only a properly grounded 3-prong receptacle or extension cord.

16.

Do not move, handle or service while hot or burning.

17.

Use only in accordance with local codes or, in the absence of local codes, with the Standard for the

Storage and Handling of Liquefied Petroleum Gases

ANSI/NFPA 58-1998.

WARNING: FIRE, BURN, INHALATION, AND EX-

PLOSION HAZARD. KEEP SOLID COMBUSTIBLES, SUCH

AS BUILDING MATERIALS, PAPER OR CARDBOARD, A

SAFE DISTANCE AWAY FROM THE HEATER AS RECOM-

MENDED BY THE INSTUCTIONS NEVER USE THE HEATER

IN SPACES WHICH DO OR MAY CONTAIN VOLATILE OR

AIRBORNE COMBUSTIBLES, OR PRODUCTS SUCH AS

GASOLINE, SOLVENTS, PAINT THINNER, DUST PAR-

TICLES OR UNKNOWN CHEMICALS.

Page 2

PROPANE FUEL PRECAUTIONS

WARNING:

Local codes for installation of propane systems may vary considerably. Therefore, ask your local propane supplier for advice on propane system installation in your particular area.

In the absence of local codes, install in accordance with

American National Standards Institute (ANSI)/National Fire

Protection Association (NFPA) publication Standard for the

Storage and Handling of Liquefied Petroleum Gases ANSI/

NFPA 58-1998. Your supplier, fire marshal or library should have a copy.

The propane supply system must be arranged for vapor withdrawal. Propane cylinders must be secured in the upright position to keep them from falling or being knocked over.

During use, liquid propane in a container vaporizes. As it vaporizes, the propane cools itself. If this cooling process continues long enough and proceeds fast enough, the propane temperature and pressure will fall so low that heater operation may be improper or even impossible even though plenty of propane remains in the container. Often frost forms on the outside of the propane container as a warning of excessive refrigeration.

Recommendations to reduce the ill effects of refrigeration are:

* Provide considerably more propane than you plan to

consume. As a rule of thumb, provide twice as much.

* Fill containers frequently, especially in cold weather.

Never allow propane to fall below one-third of con-

tainer capacity.

* If possible, keep containers in a warm area. Under

no circumstances should the heater exhaust be

directed toward the propane container.

* Watch for frost formation on the container. If it

occurs, discontinue use of the heater and refill the

container.

SIZE AND CAPACITY OF PROPANE CYLINDERS

The chart below shows the approximate size of the cylinder required for this heater. To use the chart:

1. Select the lowest air temperature expected (at the

bottom of the chart).

2. Move straight up to time of operation desired (left

side of chart).

3. Read the cylinder size required.

OPERATING INSTRUCTIONS

PREPARING FOR OPERATION

1. Check the heater for possible shipping damage. If any is found, immediately notify your dealer.

2. Follow all of the "Precautions" on pages 2 & 3.

3. Connect the POL fitting of hose and regulator assembly to the propane cylinder by rotating the POL nut counterclockwise into the propane cylinder's valve outlet and securely tighten with a wrench.

4. Connect the hose to the heater by rotating the hose fitting clockwise.

5. Securely tighten all gas connections.

6. Open the cylinder's gas valve and check all gas connections with a soap and water solution. DO NOT

USE A FLAME.

7. Connect power cord to well-grounded 115V, 60 Hz, 10 source of power.

8. When using an extension cord, make certain that it is a 3-wire (grounded) cord of proper wire size. See chart on page 4.

START

1. Slowly open the main valve at propane cylinder.

2. Set the thermostat to the desired temperature.

Heater will turn on and off automatically as the temperature varies in the heated areas.

STOP

1. Securely close valve on the propane cylinder.

2. Continue to operate heater until all fuel in the hose has burned.

3. Turn the heater thermostat to off.

RESTART AFTER SAFETY SHUTDOWN

1. Securely close valve at propane cylinder. Unplug heater.

2. Wait 5 minutes.

3. Restart following "Start" procedure.

MAINTENANCE AND STORAGE

1. The heater should be inspected before each use, and at least annually by a qualified person.

2. Before each use, check the soft "O" ring seat at the bullnose of the POL fitting. If the "O" ring is cut, scuffed, or otherwise damaged, replace it with part number 6681.

3. Turn off the gas at the LP-gas supply cylinder(s) when the heater is not in use.

4. When the heater is to be stored indoors, the connection between the LP-gas supply cylinder(s) and the heater must be disconnected and the cylinder(s) removed from the heater and stored out of doors and in accordance with Chapter 5 of the standard for

Storage and Handling of Liquefied Petroleum Gases

ANSI/NFPA 58-1998.

Recommended Minimum Gauge for Cord Extensions

Wire Gauge Chart A.W.G.

Name

Plate 120V

Amps.

25

Cord Length in Feet

50 100 150

5-6

6-8

8-12

10-12

12-14

18

18

18

16

16

16

16

14

14

12

14

12

12

10

10

12

10

10

8

8

150-FAST/SPC-150FAST

Item Part No.

150-FAST SPC-150FAST

1 1700

2 1672

3 1168

4 1146

5 1550

6 3038

7 7095

8 7094

9 1939

10 6010

11 6074

12 6041

13 6030

14 3133

15 1561

16 3087

17 6225

18 3132

19 6152

20 6255

21 6433

22 6122

23 6100

24 6123

25 1171

26 1083

27 3037

1712

6010

6074

6041

6030

3133

1561

3087

6225

3132

6152

1672

1168

1146

1550

3038

7095

7094

1940

6255

6433

6122

6100

6123

1171

1083

3037

Description

Burner Shell Assembly

Middle Cylinder Assembly

Orifice Assembly

Flame Holder Assembly

High Limit Control Assembly

Nut, Orifice

Handle

Handle Mounting Clip

Motor Shell Assembly

Set Screw, Nyloc

Fan

Nut, Lock

Screw, Machine

Support, Motor Strap

Motor Assembly

Grille, Inlet

Snap Bushing, 5/8

Saddle, Motor Support

Hose Assembly

Regulator, 11" WC

POL Excess Flow

Fitting, Male Connector

Solenoid Valve

Fitting, Male Connector

Fuel Tube Assembly

Spark Plug

Nut, Spark Plug 14 mm

1

1

1

1

1

1

1

3

1

1

1

1

Qty Item Part No. Description

150-FAST SPC-150FAST

1

1

1

1

2

1

1

1

1

1

1

1

1

2

28

**

**

**

*

*

*

**

1

*

*

*

*

3441 3441 Thermostat Mounting Bracket

Qty.

*

**

**

*

*

29 6070 6070 Clamp Loop, 5/16

30 1734 1734 Thermostat Assembly

31 10739 10739 Flame Control 1

32 3333 3333 Flame Control Bracket (7499)

33 6223 6223 Bushing, Strain Relief, 1/4

34 1036 1036 Power Cord Assembly

35 1942 1942 Thermostat Knob Assembly

36 1937 1937 Control Box Assembly

6189

7219

3210

6712

7744

6189

7219

3210

6712

7744

Terminal, "Y" Adaptor

Control (Mark 10N)

Bracket (7219)

Label, Hangtag

Label, Model/Operating Instructions

*

7789

7067

6383

7743

6374

7789

7067

6752

7743

6374

Label, BTU Rating

Label, Logo

Manual, Operating Instr.

6410 6410 Label, Thermostat

7745 7745 Parts List/Wiring Diagram

7499 7499 Flame Control

10739 10739 Flame Control Mini Potted

6641 6641 Terminal Board (7801 & 7808)

3983 3983 Bracket (7801 & 7808)

1959 1959 Harness

Label, Electrical Ground

Label, Wiring Diagram

2

1

1

2

1

1

1

1

1

1

1

1

1

1

1

2

1

1

1

1

1

1

1

** Alternate Control

*Not shown on exploded view

7745B

SEPTEMBER 2001

1

1

WIRING DIAGRAM

WIRING CHART

PART NO.

COLOR

1041

1041

1226

1226

1226

1188

1111

1959

1959

1959

1959

LENGTH

White

White

4 1/2"

4 1/2"

Red (Hi-Temp) 16 1/2"

Red (Hi-Temp) 16 1/2"

Red (Hi-Temp) 16 1/2"

Green 6"

Orange

Green

8"

7"

Red

White

Black

7"

6"

6"

FROM

Terminal Block

Flame Control Valve

High Limit Switch

Terminal Block

Flame Control Valve

Flame Control (Ground)

Flame Control (Ignition)

Flame Control (Harness)

Flame Control (Harness)

Flame Control (Harness)

Flame Control (Harness)

INSTRUCTIONS FOR ORDERING PARTS

All parts orders must show heater Model No., Item No., Part

No., and Description. We recommend that only parts supplied by the manufacturer be used on this unit. A locally purchased part may appear to be identical, although in reality it might endanger the heater or the persons operating the heater.

TO

Valve

Valve

Valve

High Limit Switch

High Limit Switch

Ground

Spark Plug

Ground

Terminal Block

Terminal Block

Terminal Block

The heater should be serviced only by a trained, experienced service person.

Read the section on "Servicing" before ordering parts.

For parts order, call (909) 981-5343.

150-FAST/SPC-150T

SERVICING

A hazardous condition may result if a heater is used that has been modified or is not functioning properly. When the heater is working properly:

* The flame is contained within the heater.

* The flame is essentially blue with perhaps some yellow tipping.

* There is no strong disagreeable odor, eye burning or other physical discomfort.

* There is no smoke or soot internal or external to the heater.

* There are no unplanned or unexplained shut downs of the heater.

The parts lists and wiring diagram show the heater as it was constructed. Do not use a heater which is different from that shown. In this regard, use only the hose, regulator and cylinder connection fitting (called a POL fitting) supplied with the heater. Do not use alternates. For this heater, the regulator must be set to supply 11" water column (W.C.) outlet pressure (.40 psig). If there is any uncertainty about the regulator setting, have it checked.

A heater which is not working right must be repaired, but

only by a trained, experienced service person. Contact the factory for the service center closest to you, phone number

(909) 981-5343.

You may also obtain in-warranty or out-of-warranty service by returning the product freight prepaid to:

Scheu Products Company

8855 Baker Avenue

Rancho Cucamonga, CA 91730

In-warranty products returned to the Service Department will be repaired with no charge for either parts or labor and will be returned to you freight prepaid. Please include a brief statement indicating date, place of purchase, the nature of the problem and proof of purchase.

Out-of-warrranty products returned to the Service Department will be repaired with a charge for parts and labor and will be returned to you freight collect.

TECHNICAL INFORMATION

HOW MUCH HEAT DO I REQUIRE?

For economy, it is important to match input to that required. But heat requirements often vary. For example, it usually takes a lot more heat to get things warm than it does to keep them that way. Likewise, outside air temperature usually changes during the day so you may need more heat at night than you do in the daytime. An approximation of the heat required can be found by using the chart below.

Cubic feet of space to be heated

BTU'S PER HOUR REQUIRED

Temperature Rise Required ( o F)*

20 o 30 o 40 o 50 o

5,000

7,000

10,000

15,000

20,000

14,000

19,000

27,000

40,000

54,000

20,000

28,000

40,000

60,000

27,999

38,000

54,000

34,000

47,000

67,000

80,000 100,000

80,000 107,000 133,000

30.000

80,000 120,000 160,000 200,000

50,000 133,000 200,000 266,000 333,000

WARNING: When using a thermostat the heater exit area should be protected from personnel and warnings posted of sudden startup.

Page 4

ANSI Z83.7b-1993/CGA 2.14-1972

Construction Heater

SCHEU PRODUCTS COMPANY, INCORPORATED

MAIL: P.O. BOX 250, UPLAND, CA 91785

PLANT: 8855 BAKER AVE., RANCHO CUCAMONGA, CA 91730

TELEPHONE: 909-981-5343

P/N 7743D

September 2000

advertisement

Related manuals

Download PDF

advertisement