Model No. 831.488540 User's Manual Setup 1. Firmly press the thumb tab and pivot the upright up until it locks in a nearly vertical position. 2. Insert the handles into the stem until the lock pins are visible in the holes in the stern. 3. Hand Open the quick-release lever. Depress the lock pin on the stem and slide the stem up until the lock pin is visible in one of the three holes in the upright. When the stem is at the desired height, close the quick-release lever so that it is snug against the upright. If the quick-release is not snug, see ADJUSTING THE QUICK-_SE on the back of this user's manual. Before using the scooter, make sure that the scooter is set up as described and that all parts are securely tightened. The decal shown at the right has been placed on the scooter. If the decal is missing, or if it is not legible, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time, to order a free replacement decal. Apply the replacement decal to the location shown. To prevent serious Injury: •Read, understand and follow all warnlngs and Instructions on the unit and in the manual, •Always wear protecllve equipment Including helmet, kneapads, wrlst guards, and elbow pads. •Keep away from cars, streets or areas that enter vehicle traffic mutes. •Never ride when towed behind bicycles, motorcycles, or vehicles Right Side •Do not ride at night or In poor visibility Storage 1. Open thequick-release lever. Depress the lock pin on the stem and slide the stem down into the upright. Close the quickrelease lever. 2 3 Depress the lock pins and remove the handles from the stem. Press the handles into the storage clip on the upright. Pull the thumb tab and pivot the upright down until it locks in the horizontal position. Hand Brake, Carry Strap, and Cable not shown. Part List/Exploded No. Qty. Drawing Model No. 831.4ui:i )4u R0700A Description 1 2 3 1 1 1 Deck Head Tube Fork 4 5 6 7 1 1 2 2 Upright Stem Handle Foam Pad 8 9 10 2 3 1 Handle Cap Lock Pin Handle Cord 11 12 13 14 15 16 17 18 19 20 21 1 1 1 1 2 2 2 1 1 2 2 Quick Release Upright Clamp w/Ring Bearing Nut Bearing Cap Bearing Bearing Race Bushing Pivot Union Bolt Set Front Union Bolt Set Rear Union Bolt Set Wheel 22 23 24 2 1 1 Rear Wheel Spacer Brake Spring Brake 25 26 27 28 29 30 31 32 33 34 1 1 2 1 1 1 1 4 1 2 Head Tube Spring Storage Clip Front Wheel Spacer Lock Pin Deck Mount Deck Cushion Frame Deck Screw Cable Clip Tek Screw 35 36 37 38 39 40 2 1 1 1 1 1 Brake Spacer Mount Union Bolt Set Hand Brake Brake Bracket Cable Bracket Brake Cable 41 42 * * 2 1 1 1 Flange Nut Strap Clamp w/Ring Carry Strap User's Manual *The user's manual and carry strap are not shown Note: Specifications are subject to change without notice. 28 19 27 Ordering Replacement Parts To order replacement parts, call toll-free 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please mention the model number (831.488540) and the number and description of the parts needed. If the quick-release doesn't hold the stem snug in place, you will need to adjust it. Open the quick-release lever. Turn the adjustment nut clockwise one half turn while keeping the lever from turning. Close the lever. Repeat this procedure until the stem is held snug in place. If the quick-release is too snug to close, you will need to adjust it. Quick Release Close Open Adjustment Nut While the quick-release lever is open, turn the adjustment nut counterclockwise one quarter tern while keeping the lever from turning. Close the lever. Repeat this procedure until the stem is held snug in place and the quick-release is closed. Part No. 167662 R0700A Printed in China © 2000 ICON Health & Fitness, Inc.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project