TECHNICAL
P r r a
2 1
S T c t t i i c e
C
E N T U R Y
T
E L E C O M
S
O L U T I I O N S F O R T H E
Hot Line Phones
June 27, 2002
Economical and Vandal Resistant
Hot-Line Phones
K-1900-6
K-1900W-2 ASH
K-1900D-2
K-1900D-2
F e a t t u r r e s
• Telephone line powered
• Hearing aid compatible amplified handsets
• Rotary handset volume control
• 1 - 20 digit programmable speed dial number
• Touch Tone and 10/20 pps pulse dialing
• Non-volatile E 2 memory (no batteries required)
• Restricts fraudulent calls from hand held dialers
• K-1900D/W-2 available in red or ash
• Optional Q170600 ringer (Fax Back Doc 845)
• Operates on a C.O. line or analog PABX/KSU extensions
• Ring detection (will not dial on incoming calls)
• Programmable security code to enter programming mode
• Touch Tone programmable
• K-1900-6 fits standard 500, 554, 2500 and
2554 set phones
The K-1900 Series of Hot-Line phones are programmable to dial a 1-20 digit telephone number each time the phone’s handset is lifted. The products may be programmed to Touch Tone
K-1900D-2 ASH or pulse dial and will not dial on incoming calls.
K-1900-7
The K-1900 Series phones are available in a desk or wall chassis, as well as in a vandal resistant panel phone configuration. A network insert dialer is also available, to convert standard phones into hot-line phones.
K-1900W-2
A p p l l i i c a t t i i o n s
• Catalog sales
• Information kiosks in malls
• Courtesy and customer service phones
• Automated tellers
• Hot-line reservation phones
• Replace leased Ringdown circuits
• Security and emergency phones (pools, etc.)
P h o n e .
.
.
.
.
.
7 1 5 .
.
3 8 6 .
.
8 8 6 1 i i n f f o @ v i i k i i n g e l l e c t t r r o n i i c s .
.
c o m h t t t t p : : / / / / w w w .
.
v i i k i i n g e l l e c t t r r o n i i c s .
.
c o m
S p e c i i f f i i c a t t i i o n s
Power: Telephone line powered (20V DC/18mA minimum)
Environmental: 0°C to 32°C (32°F to 90°F) with 5% to 95% non-condensing humidity
Dimensions: (see page 2)
Dialing Speed: Normal - 120ms tones/10 pps, Fast - 50ms tones/20 pps
S p e c i i f f i i c a t t i i o n s a n d I I n s t t a l l l l a t t i i o n
Viking offers three variations of hot-line phones and one network dialer. Below are model numbers and descriptions of the Hot
Line phones Viking offers. Each model is designed for specific applications, including varying mounting capabilities and levels of vandal protection. The following sections describe the product model numbers, their applications, installation and specifications.
!
Important: Use a minimum wire gauge of 26 when connecting the K-1900 phone to the public switched network.
K 1 9 0 0 D 2 H o t t L i i n e D e s k
To install the K-1900D-2 insert the RJ11 plug into a standard RJ11 jack
P h o n e
K-1900D-2 as shown to the right.
RJ11
(not included)
Dimensions: 230mm x 210mm x 120mm (9.0” x 8.25” x 4.75”)
Shipping Weight: 1.36 Kg (3 lbs)
Connections: RJ11
Colors: Red or Ash
C.O. Line or Analog
PABX/KSU Extension
K 1 9 0 0 W 2 H o t t L i i n e W a l l l l P h o n e
To install the K-1900W-2 line up the pins of the RJ11W jack with the slots on the back of the phone, insert and press down as shown to the right.
RJ11W
(not included)
Dimensions: 102mm x 108mm x 222mm (4.0” x 4.25” x 8.75”)
Shipping Weight: 1.36 Kg (3 lbs)
Connections: RJ11W
Colors: Red or Ash
K-1900W-2
-or-
C.O. Line or Analog
PABX/KSU Extension
Optional VE-9x12 Weatherproof Housing for the K-1900W-2, available in emergency red or safety yellow. For more information on the VE-
Optional VE-9x12
9x12, retrieve Fax Back Document 413.
K 1 9 0 0 6 H o t t L i i n e D i i a l l e r r N e t t w o r r k
Fax Back Doc 413
(not included)
K-1900-6 PCB with Standard Network
Mounting Bracket (included)
The K-1900-6 Hot-Line Dialer Network can be used with any carbon microphone handset and a double pole hook switch or typical 500, 554, 2500 and 2554 phones. Attach wires as shown to the right. An electronic ringer may be used if inbound call capability is required.
C.O. Line or Analog
PABX/KSU
Extension
Green
Red
T
R
0.47 mF @ 250V
Capacitor
(included)
N.O.
Slate/White
Required Handset Type: Carbon microphone
Required Hookswitch: One normally open contact and one normally closed contact
Dimensions: 88.9mm x 68.6mm x 33mm (3.5” x
2.7” x 1.3”)
Shipping Weight: 0.45 Kg (1.0 lb)
Connections: Miniature spade receptacles
Compatible Phones: 500, 554, 2500 and 2554
Hookswitch
(shown on hook)
N.C.
Slate/Green
Slate/Red
Slate/Black
S1
S2
RX2
RX1
TX1
TX2
Note: If the phone has a ringer, the included capacitor MUST be installed as shown above.
White or
Green
White
Black
Red
K 1 9 0 0 7 H o t t L i i n e P a n e l l P h o n e
To install the K-1900-7 vandal resistant hot line panel phone, attach the panel to an existing double gang box (with minimum dimensions shown right) using the provided screws. Insert a cord into the RJ11 jack on the back of the K-1900-7.
Note: Four extra screws and nuts are provided to fill the unused mounting holes.
20.25"
T
E
L
E
P
H
O
N
E
- or -
10.14"
3.69"
5.22"
Dimensions: 127mm x 254mm x 102mm (5” x
10” x 4”)
Shipping Weight: 1.36 Kg (3 lbs)
Connections: RJ-11
Panel Material: .125 inch stainless steel
Mounting: Flush mount to the included double gang box. Optional VE-5x10 weather resistant surface mount box and VE-9x20 weatherproof box for outdoor applications available.
9.25"
Optional VE-9x20
Weatherproof Box
Fax Back Doc 413
(not included)
Optional VE-5x10
Surface Mount Box
Fax Back Doc 424
(not included)
- or -
Double Gang
Electrical Box
(not included)
2.75"
2.1"
3.5"
C.O. Line or
Analog PABX/KSU
Extension
T
E
L
E
P
H
O
N
E
Optional Ringer
(not included)
Carbon Mic
Handset
(not included)
Side View of the K-1900-7
#6-32 x 3/4”
Stainless Steel
Hexdrive Screws
Included
P r r o g r r a m m i i n g
While in the programming mode, two beeps indicate a valid programming entry. An invalid entry will be indicated with three beeps. To exit programming, simply hang-up the K-1900 Series phone.
A. Accessing the Programming Mode
1. Using the Security Code
Step 1. Connect the K-1900 Series device to an analog C.O. line, or an analog PABX/KSU station.
Step 2. From a Touch Tone phone, call into the K-1900 Series phone.
Step 3. Listen for at least one ringback in the calling phone and then take the K-1900 Series phone off-hook (answer the phone).
Step 4. From the Touch Tone phone, enter your six digit security code (factory set to 845464 - see section E).
Step 5. A double beep indicates the K-1900 Series phone is in the programming mode (see sections B-G ). If six digits are entered and no beeps are heard, an incorrect security code has been entered. Repeat steps 2-5 or follow directions in 2. Without a Security Code below.
2. Without a Security Code (If You Have Forgotten or Lost the Security Code)
Step 1. Remove JP1 (as shown to the right). For the K-1900W-2 and K-1900D-2, the plastic cover must be removed to expose the circuit board.
Step 2. Connect the K-1900 Series device to a C.O. line, analog PABX/KSU station or to a DLE-200B Line Simulator.
Step 3. From a Touch Tone phone, call into the K-1900 Series phone.
Step 4. Listen for at least one ringback in the calling phone and then take the K-1900
Series phone off-hook (answer the phone).
Step 5. A double beep indicates the K-1900 Series phone is in the programming mode
(see Programming sections B-G).
Step 6. When programming is finished, replace JP1 and replace cover on phone.
JP1
Remove to enter programming without a security code.
B. Quick Programming Guide
Note: JP1 MUST be in place for normal operation.
Enter Digits
Speed dial number (see section C) 1-20 digits or pauses .............................................
Security Code, factory set to 845464 (see section E) ...................................................
To add a ✱ anywhere in the dialing string .....................................................................
To add a # anywhere in the dialing string ......................................................................
To set dialing speed to normal - 120ms tones/10 pps (factory setting) ..........................
To set dialing speed to fast - 50ms tones/20pps ...........................................................
To restrict Touch Tone user dialing (factory setting) ......................................................
To enable Touch Tone user dialing ................................................................................
Toggles between pulse and Touch Tone dialing (see section C) ...................................
To add a 4 second pause anywhere in the dialing string (see section C) ......................
To add a 1 second pause anywhere in the dialing string ...............................................
phone number
6 digits
✱ 4
✱ 6
✱ 7
✱ 8
✱✱
✱ #
✱ 1
✱ 2
✱ 3 then then then
Memory
Location
#0
#9
C. Programming Examples
To Program the ACD-10 to...
...to Touch Tone dial 555-1234
...to pulse dial 555-1234 followed by a Touch Tone 9
...to dial a 9, a 4 second pause and then 555-1234
...to set the dialing speed to fast
...to enable unlimited user dialing after the phone has speed dialed
...to clear the speed dial number or disable speed dialing
Step 1 - See section A
Enter Programming
Enter Programming
Enter Programming
Enter Programming
Enter Programming
Enter Programming
Step 2 - Enter Digits
5551234 + #0
✱ 6 5551234 ✱ 6 9 + #0
9 ✱ 7 5551234 + #0
✱
2
✱ 4
#0
D. Touch Tone and Pulse Dial Speeds
The K-1900 Series phone can be programmed to dial at normal or fast dialing speeds. While in the programming mode, enter ✱ 1 for normal dialing speed - 120ms on/off Touch Tones or 10 pps pulse dialing. Enter ✱ 2 for fast dialing speed - 50ms on/off Touch Tones or 20 pps pulse dialing.
E. Security Code
A six digit security code is required to access the programming mode. The factory set security code is 845464 (V-I-K-
I-N-G). It is recommended that you change the security code to a personal 6 digit (0-9) number in memory position #9 while in the programming mode. Note: The security code must be six digits in length and cannot contain a ✱ or #.
F. Touch Tone or Pulse Dialing
The K-1900 Series phones are factory set to automatically dial using Touch Tones. A ✱ 6 entered in the speed dial number will toggle the dialing mode between Touch Tone and pulse (see section C).
Note: You can NOT program a ✱ and # to be pulse dialed.
G. Touch Tone User Dialing Restriction (factory enabled)
The K-1900 Series phones is factory set to restrict fraudulent calls from hand held pocket dialers. After speed dialing, the K-1900 Series phones will restrict (hang up) when they detect any Touch Tone that they did not generate. To restrict user dialing, enter ✱ 3 while in the programming mode. To enable user dialing, enter ✱ 4 while in the programming mode.
A d d i i n g a n I I n t t e r r n a l l R i i n g e r r
An optional Q170600 internal ringer is available. For more information, retrieve Fax Back Document 834.
T
R
.47 mF @ 250V
(included with ringer)
Q170600
Electronic Ringer
R e l l a t t e d P r r o d u c t t s
Install Your Viking Product in a Weatherproof Enclosure
Weatherproof
Enclosures
The VE-9x12 and VE-9x20 provide the ultimate in weather protection for your Viking product!
The enclosures are constructed of cast aluminum and is made for years of outdoor service. The heavy-duty aluminum door is labeled “Telephone” and has a gasket seal to keep out even the harshest weather. The VE-
9x12 and VE-9x20 are available in two high visibility colors: safety yellow or emergency red.
For more information on the VE-9x12 or VE-9x20, retrieve Fax Back Document 413.
Vandal Resistant Hot-Line Panel Phone with Touch Tone Keypad
K-1900-8
Shown with VE-5x10
The K-1900-8 Stainless Steel Panel Phone features a built-in Hot-Line dialer as well as a weather resistant keypad. The dialer can provide both Touch Tone dialing as well as 10/20 pps pulse dialing. After the phone number has been dialed, the Touch Tone keypad is enabled to permit additional manual dialing.
The K-1900-8 housing consists of a heavy gauge, stainless steel panel, a metal Touch Tone keypad, an armored cable, and an all metal cradle for both weather and vandal resistance.
For more information on the K-1900-8 Hot-Line Panel Phone, retrieve Fax Back Document 312. For more information on the VE-Series Surface Mount Boxes, retrieve Fax Back Document 424.
P r r o d u c t t S u p p o r r t t L i i n e .
.
.
.
.
.
7 1 5 .
.
3 8 6 .
.
8 6 6 6 F a x B a c k L i i n e .
.
.
.
.
.
7 1 5 .
.
3 8 6 .
.
4 3 4 5
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
Fax Back Doc 360 Printed in the U.S.A.
ZF300950 Rev G
