VTech | t2326 | User's Manual | VTech T2326 User's Manual

Table of contents
Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . 3
Parts checklist . . . . . . . . . . . . . . . . . . . . . . . . . 3
Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Choose a location . . . . . . . . . . . . . . . . . . . . . . . 4
Install handset battery . . . . . . . . . . . . . . . . . . . . . 4
Table/desk installation . . . . . . . . . . . . . . . . . . . . . 5
If you subscribe to DSL service . . . . . . . . . . . . . . . . 5
Wall mounting . . . . . . . . . . . . . . . . . . . . . . . . . 5
Charge the handset battery . . . . . . . . . . . . . . . . . . 6
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Set handset date and time . . . . . . . . . . . . . . . . . . . 6
Check for dial tone . . . . . . . . . . . . . . . . . . . . . . . 7
Dial mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Set the ringer . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Message waiting . . . . . . . . . . . . . . . . . . . . . . . . 8
Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . 9
Telephone operation . . . . . . . . . . . . . . . . . . . . . . . 9
Handset operation . . . . . . . . . . . . . . . . . . . . . . . 9
Base unit operation . . . . . . . . . . . . . . . . . . . . . 10
Temporary tone dialing . . . . . . . . . . . . . . . . . . . . 11
Operating range . . . . . . . . . . . . . . . . . . . . . . . 11
Speed dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Store a number/name in speed dial . . . . . . . . . . . . . 13
Edit a number/name in speed dial . . . . . . . . . . . . . . 15
Delete a number/name in speed dial . . . . . . . . . . . . 15
Dial a speed dial number . . . . . . . . . . . . . . . . . . 15
Reassign locations in speed dial . . . . . . . . . . . . . . 15
Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Store a number/name in the directory . . . . . . . . . . . . 16
Edit a number/name in the directory . . . . . . . . . . . . . 17
Delete a number/name in the directory . . . . . . . . . . . 17
Dial from the directory . . . . . . . . . . . . . . . . . . . . 18
Move a number/name to memory . . . . . . . . . . . . . . 19
Caller ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
About call history (caller ID) . . . . . . . . . . . . . . . . . 21
Review call history . . . . . . . . . . . . . . . . . . . . . . 21
Delete records from call history . . . . . . . . . . . . . . . 21
Dial a displayed number . . . . . . . . . . . . . . . . . . . 22
Store a call history entry to the directory . . . . . . . . . . 22
Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Battery care and maintenance . . . . . . . . . . . . . . . . 24
Replace the handset battery . . . . . . . . . . . . . . . . . 24
Additional information . . . . . . . . . . . . . . . . . . . . 25
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 25
If you subscribe to DSL service . . . . . . . . . . . . . . . . . 31
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Important safety instructions . . . . . . . . . . . . . . . . . . 34
FCC, ACTA and IC regulations . . . . . . . . . . . . . . . . . 35
The RBRC ® seal . . . . . . . . . . . . . . . . . . . . . . . . 37
Technical specifications . . . . . . . . . . . . . . . . . . . . .38
www.vtechphones.com
NEED HELP?
This book has all the feature operations and troubleshooting you need to install
and operate your new VTech innovative and feature-rich telephone. Please take
the time to review it thoroughly to ensure proper installation. You can also visit our
website at www.vtechphones.com for support, shopping, and everything new at
VTech. In Canada, please visit www.vtechcanada.com
VTech toll free 1(800)595-9511
In Canada, dial 1(800)267-7377
Parts checklist:
1.Handset
2.Base unit
3.AC power adapter
4.Telephone line cord
5.Battery
6.User’s manual
7. Battery compartment cover
To purchase replacement
batteries, visit us on the web at
www.vtechphones.com or call
VTech Communications, Inc. at
1(800)595-9511.
In Canada, visit us at
www.vtechcanada.com or call
VTech Telecommunications
Canada Ltd. at 1(800)267-7377.
• Important!
Before using
this telephone,
you must read
Important safety
instructions on
page 34.
AC power adapter
Handset
Base unit
Telephone line
cord
User’s manual
Battery
Battery compartment
cover
www.vtechphones.com
Getting started
Before you begin
Installation
• Use only the VTech
battery and AC power
adapter supplied with this
unit or the recommended
equivalent.
•�������������������������
Do not open or mutilate
the battery. Released
electrolyte is corrosive
and may cause damage
to the eyes or skin. It may
be toxic if swallowed.
•���������������������������
Exercise care in handling
batteries in order not to
create a short circuit with
conducting materials
such as rings, bracelets,
and keys. The battery or
conductor may overheat
and cause burns.
•�����������������������
Do not dispose of the
battery in a fire; it might
explode.
•�����������������������
Return the handset to
the base unit when not in
use to ensure optimum
performance.
Choose a location
Install handset battery
For optimum performance of your cordless telephone
system, choose a central location close to a telephone
jack and a power outlet not connected to a switch. The
base unit���������������
can be placed �����
on a ����������������
flat surface or ��������
mounted
on the wall. For maximum range and best reception,
place the ��������������������������������������
base unit�����������������������������
in a high and open location.
Avoid putting the base unit too close to:
•��������������������������������������������������
communication devices such as personal computers,
computer routers, television sets, VCRs, wireless
routers (wireless broadband, 802.1.1 routers, wi-fi,
etc.) and other cordless telephones, etc.
•������������������������������������������������������
excessive heat sources such as radiators, ventilation
ducts, and direct sunlight.
•������������������������������������������
noise sources such as a window with heavy traffic
��������
outside, motors, microwave ovens, refrigerators,
and fluorescent lighting.
•��������������������������������������������������
excessive dust sources such as: workshop, garage,
etc.
•���������������������������������������������
excessive moisture sources�������������������
��������������������������
such as bathroom,
kitchen, sauna, or greenhouse.
•�����������������������������������������
extremely low temperature such as garage.
•����������������������������������������������������
mechanical vibration or shock such as on top of the
washing machine.
1. Plug the battery connector securely into the jack inside
the battery compartment according to the color-coded
label.
2.Insert battery in the center of the battery compartment.
3.Press down on the wired side until the battery securely
snaps into place.
4.Neatly tuck the wires next to the battery inside the battery
compartment.
5.Position the battery compartment cover and slide it
towards the unit until it clicks into place.
6.Put the handset in the base unit to start charging the new
battery for at least 16 hours.
Black
wire
Red
wire
www.vtechphones.com
2
Red Black
wire wire
1
Getting started
Installation
Table/desk installation
1. Plug the connector of the AC power adapter
to the jack marked AC 9V at the bottom of
the base unit. Plug the AC power adapter
into a standard electrical outlet (110V AC)
not controlled by a wall switch.
2. Connect the telephone line cord to the jack
marked TEL LINE at the bottom of the base
unit. Plug the other end of the telephone line
cord to a wall jack.
�����������������
����
If you subscribe to DSL service
�������������������
������
If there is interference during telephone
conversations and/or your caller ID features
are not functioning properly, install a noise
filter to the telephone line between the base
unit and the telephone wall jack. Contact
your DSL provider for a noise filter.
Wall mounting
1. Connect the AC power cord and the
telephone line cord as described in the
Table/Desk Installation section above.
www.vtechphones.com
Installation
•If you are not
going to use the
telephone for a
long period of
time, remove the
battery to prevent
possible leakage.
•If you have
any trouble
installing your
telephone, please
refer to the
Troubleshooting
section on pages
25-31 of this
manual.
2.Mount the base unit on the wall. Position the �����������������
base unit so
�������
the ����������������������������
mounting studs fit into the
holes on the wall mount bracket. Slide the �������������������������������������������
base unit����������������������������������
down on the mounting studs until
it locks into place.
Charge the handset battery
Place the handset in the �����������
base unit��. CHARGING... will display on handset. Be sure to charge the
battery for at least 16 hours before using your telephone.
Language
• Press PROG, then press once and LANGUAGE is displayed. Press SELECT.
• The current setting blinks. Press or to toggle between English and Spanish until the desired
language is blinking on the screen.
• Press SELECT to save.
Set handset date and time
If you subscribe to caller ID service, the date and time will be set automatically with the first incoming
call. If you do not have caller ID service, you can set the date and time manually:
• Press PROG, then press until DATE/TIME is displayed. Press SELECT.
• When the month is blinking, press or until the screen displays the correct month. Press
SELECT.
•��������������������������������
When the������������������������
day is blinking,
����������������
press� or until the screen displays the correct day. Press SELECT.
•���������������������������������
When the�������������������������
hour is ����������������
blinking, press� or until the screen displays the correct hour. Press
SELECT.
www.vtechphones.com
• When the minute is ���������������
blinking, press
Press SELECT.
• When AM or PM is blinking, press or
is blinking, press SELECT.
or
until the screen displays the correct minute.
to select between AM or PM. When the desired setting
Check for dial tone
fter the batteries are charged, press TALK on the handset; you should hear a dial tone, otherwise,
A
try plugging this telephone to another telephone jack.
Dial mode
If you have touch tone service, your phone is ready to use as soon as the battery is charged. If you
have pulse (rotary) service, it is necessary to change the dial mode.
• Press PROG.
• Press until the screen displays DIAL MODE: and the current setting.
• Press SELECT. The current setting blinks.
• Press or to toggle between TONE and PULSE until the desired dial mode is blinking.
• Press SELECT to save.
•In the event
of a power
outage, or if
your telephone’s
power cord is
unplugged, it is
necessary to set
the time again
(see page 6).
Set the ringer
• Press PROG. Press twice, the name of the current ringer will display and the tone of the ringer will
be heard.
• Press or to scroll through the four ringers. Press SELECT when the desired ringer is displayed
and heard.
www.vtechphones.com
Getting started
Installation
Installation
•�You’ll
��������������������������������
hear a confirmation tone.
Message waiting
Your phone has visual message waiting indication if you subscribe
to voice message service from your service provider.
You can choose to have the message alert setting on or off.
•�������
Press PROG, then press
until MESSAGE WAITING is
displayed. Press SELECT.
•�����������������
The screen shows MSG ALERT OFF: Y.
•�������
Press or to toggle between Y (yes) or N (no).
MESSAGE WAITING
MSG ALERT OFF: Y
www.vtechphones.com
Telephone operation
Handset operation
www.vtechphones.com
5
6
7
9
Basic operation
1. Make a call (TALK)
Press before or after dialing a telephone number to place a call.
During a call, press to receive an incoming call if call waiting service is activated.
1
2. Channel (CHAN)
If there is interference while on a call, press CHAN to switch to a clearer channel.
3. DELETE
Press to delete one or all calls from the call log. See page 21 for complete instructions.
4. Answer a call (any key except OFF)
4
Press any key (except OFF) to answer a call.
5. Handset volume
Adjust the volume while on a call. A double beep will sound
when you reach the maximum or minimum setting.
CID and DIR keys
• When in idle mode, press /CID to display caller ID information. 2,3
• When ��������������������
in idle mode��������
, press /DIR to display directory entries.
6. SELECT
Press to confirm the highlighted option while in programming mode.
7. OFF
During a call, press to hang up. While in programming mode, press to cancel an operation, back up, or exit.
8.REDIAL/PAUSE
Press to view redial memory. While entering numbers, press and hold to insert a dialing pause.
9. Program (PROG)
Press to enter programming mode.
8
Telephone operation
Base unit operation
1. Locate handset
• Press the LOCATE HANDSET key to page
the handset.
• Press again to cancel a page.
• The base unit will ring the handset for
o n e m i nu te b efore e n d i n g t h e p ag e
automatically.
• By pressing the OFF key on the handset, or
returning the handset to the base unit, you
can cancel the handset page.
10
�
www.vtechphones.com
Telephone operation
Temporary tone dialing
Operating range
This cordless telephone operates within the maximum power allowed by the Federal
Communications Commission (FCC). Even so, this handset and base unit can communicate over only
a certain distance — which can vary with the locations of the base unit and handset, the weather,
and the construction of your home or office.
If there is a call while the handset is out of range, it might not ring; or if it does ring, the call might
not connect well when you press TALK. Move closer to the base unit, then press TALK to answer
the call.
If you move out of range during a telephone��������������������������������������������������������
�����������������������������������������������������������������
conversation, there might be noise or interference. To
improve reception, move closer to the base unit.
If you move out of range without pressing OFF, the telephone will be left off the hook. To hang up
properly, walk back into range, periodically pressing OFF.
www.vtechphones.com
• Temporary tone
dial mode is useful
if it is necessary
to send touch tone
signals to access
telephone banking
or long distance
services.
• For clearer
reception while on
a call, press the
CHAN button until
the interference
has been
eliminated.
11
Basic operation
If you have pulse (rotary) service, you can change from pulse to touch tone dialing during a call by
pressing TONE *.
1. Dial the number.
2. Press TONE *. Buttons pressed after this send touch tone signals.
3. After you hang up, the phone automatically returns to pulse service.
Telephone operation
Display screen messages
12
Screen displays:
When:
** RINGING **
There is a call coming in.
CONNECTING...
The handset is waiting for a dial tone.
PHONE ON
The handset is in use.
CHARGING
The handset is in the base unit and the battery is
charging.
** PAGING **
The base unit is paging the handset.
BATTERY LOW
The battery needs to be recharged.
SCANNING...
The handset is changing to one of the 30 channels
available.
CAN’T CONNECT
The power on the base unit is off and TALK is
pressed.
RINGER OFF
The handset ringer is turned off.
www.vtechphones.com
Speed dial
You can store frequently called numbers either as speed dial numbers or in the directory. Each entry can contain
up to 24 digits. You can program names with the numbers, each �������������������������������������������������
containing���������������������������������������
up to 15 characters. Up to 10 numbers
and names can be stored alphabetically in the directory, and nine numbers with names into designated speed dial
memory locations (1 through 9). See Directory beginning on page 16 for instructions.
Store a number/name in speed dial
2. Press
once and the screen displays SPEED DIAL.
3. Press SELECT and the screen displays ENTER 1-9.
4.Press the key (1 through 9) for the memory location to store this entry. The screen displays ENTER NAME.
5.Using the chart on the next page, enter up to 15 characters for the name to be stored with the number. Use
to backspace and make corrections; use to advance and add a space.
Basic operation
1. Press PROG on the handset.
•The entries
stored in speed
dial memory will
be marked with
01 through 09 in
the telephone
directory.
• Press OFF
anytime to exit
memory mode.
6.When finished entering the name, press SELECT. The screen displays ENTER NUMBER.
7.Enter the telephone number using the number keys. Use to backspace and make corrections. After at least
one digit has been entered, press REDIAL/PAUSE to store pauses in the dialing sequence, if necessary.
Press REDIAL/PAUSE to display the last number dialed.
8.Press SELECT to store your entry. The screen displays DISTINCT RING? and the current setting.
9.Press or to change the setting. Choose Y (for yes) if you wish the telephone to alert you to calls from this
number by changing to a distinctive ringing pattern after the first ring. Choose N (for no) for a normal ringing
pattern.
10. Press SELECT to confirm your selection. If you chose Y, a D (for distinct ring) will be displayed with the
directory entry.
www.vtechphones.com
13
Speed dial
•When the directory
memory is full, the
screen displays
MEMORY FULL
and an error tone
sounds. You
cannot store a new
number until you
delete a record
from speed dial
memory or the
directory.
•If the speed dial
location is not
empty, the new
entry will replace
the old and the
first entry will be
deleted. Take
caution to not save
over entries that
you do not wish
to delete from
memory.
14
Press
Once
Twice
3 Times
4 Times
1
1
2
A
B
C
2
3
D
E
F
3
4
G
H
I
4
5
J
K
L
5
6
M
N
O
6
7
P
Q
R
S
8
T
U
V
8
9
W
X
Y
Z
9
0
0
*
*
#
&
‘
,
-
.
www.vtechphones.com
5 Times
6 Times
7
#
Speed dial
Edit a number/name in speed dial
Basic operation
1. Press and hold the memory location key (1 through 9) of the entry
SPEED EDIT ERASE
to be edited.
8005959511
2. When the screen displays the entry to be edited, press SELECT,
01
then press or until EDIT flashes.
3. Press SELECT. The screen displays the name and number. The
cursor appears at the end of the name. Use , and the dial pad keys to edit the name.
4. To edit the number, press SELECT. Use to backspace and make corrections.
5. To edit the distinctive ring setting, press SELECT. Use or to change the setting.
6. Press SELECT, you’ll hear a confirmation tone.
Delete a number/name in speed dial
1. Press and hold the memory location key (1 through 9) of the entry to be deleted.
2.Press SELECT when the entry is displayed, and press � or until
ERASE flashes.
SPEED EDIT ERASE
8005959511
3. Press SELECT, the screen displays a choice of YES or NO.
01
4. Press
or until YES flashes.
5. Press SELECT, you’ll hear a confirmation tone.
Dial a speed dial number
• Press and hold the memory location key (1 through 9) of the entry you wish to dial.
• Press TALK to dial the displayed memory number.
Reassign locations in speed dial
1. Press and hold the memory location key (1 through 9) of the entry
SPEED EDIT ERASE
8005959511
01
www.vtechphones.com
15
Speed dial
•Press REDIAL/
PAUSE to display
the last number
dialed from this
telephone to
store it in speed
dial memory.
to be reassigned.
2.W hen the screen displays the desired entry, press SELECT. Then press
until SPEED
flashes.
3. Press SELECT. The screen displays ENTER 1-9.
4.Press the keys (1 through 9) to reassign this entry into another memory location.
Directory
Your telephone can store 10 (including the nine speed dial entries) numbers with names (up to 15
characters for the name and 24 digits for the number) in each handset.
When the memory is full, the screen displays MEMORY FULL, and an error tone sounds. You will not
be able to store a new number until a stored number is deleted.
Store a number/name in the directory
1. Press PROG. The screen displays DIRECTORY.
2. Press SELECT. The screen displays ENTER NAME.
3.Using the chart on page 14, enter up to 15 characters for the name. Use� to backspace and make
corrections; use to advance and add a space.
4.When you finish entering the name, press SELECT. The screen displays ENTER NUMBER.
5.Enter the telephone number. Use to backspace and make corrections.
Press REDIAL/PAUSE to store a pause in the dialing sequence.
-ORPress REDIAL/PAUSE if you wish to display and store the last number dialed.
16
www.vtechphones.com
Directory
• Press OFF at
any time to exit
the directory.
Basic operation
6. Press SELECT. The screen displays DISTINCT RING? and the current setting.
7.Press or to change the setting. Choose Y (for yes) if you want the telephone to alert
you to calls from this number by changing to a distinctive ringing pattern after the first ring.
Choose N (for no) for a normal ringing pattern.
8.Press SELECT to confirm your selection. If you chose Y, a D (for distinct ring) will be displayed with
the directory entry.
Edit a number/name in the directory
1. Press (DIR). The screen displays DIRECTORY.
2. Press or to scroll alphabetically through the entries.
-OR Press the dial pad key for the first letter of the entry to be edited.
3.Press SELECT when the entry is displayed, and press � or until EDIT flashes.
4.Press SELECT. The screen displays the name and number. The cursor appears at the end of the
name. Use , and the dial pad keys to edit the name.
5. To edit the number, press SELECT and use to backspace and make
SPEED EDIT ERASE
corrections.
8005959511
6. To edit the distinctive ring setting, press SELECT and press or to
change the setting.
7. Press SELECT to save the edited information.
Delete a number/name in the directory
1. Press
(DIR). The screen displays DIRECTORY.
www.vtechphones.com
17
Directory
•Press OFF
anytime to exit
directory.
2. Press
or
to scroll alphabetically through entries in the
SPEED EDIT ERASE
directory.
8005959511
-OR
Press the dial pad key for the first letter of the entry to be deleted.
3. Press SELECT when the entry is displayed, and press or until ERASE flashes.
4.Press SELECT. The screen displays ERASE NO YES and the number. The current choice
flashes.
5. Press or until YES flashes.
6. Press SELECT, and you will hear a confirmation beep.
Dial from the directory
1. Press (DIR). The screen displays DIRECTORY.
2. Press or to scroll alphabetically through entries stored in directory.
-OR Press the dial pad key for the first letter of the entry to be dialed.
3. Press TALK when the number is displayed.
18
www.vtechphones.com
Directory
Move a number/name to memory
www.vtechphones.com
Basic operation
1. Press (DIR). The screen displays DIRECTORY.
2. Press or to scroll alphabetically through directory.
SPEED EDIT ERASE
-OR8005959511
Press the dial pad key for the first letter of the entry to be moved.
3.When the screen displays the entry to be moved, press SELECT.
Then press until SPEED flashes.
4. Press SELECT. The screen displays ENTER 1-9.
5.Press the key (1 through 9) to move this entry from the normal directory to the speed dial memory
and assign a memory location. You’ll hear a confirmation tone. A memory location number (01
through 09) will be displayed with this entry.
19
Caller ID
Your phone has a caller ID (CID) with call waiting feature that works with service from your local
telephone service provider. Caller ID with call waiting lets you see who’s calling before answering
the telephone, even when on another call.
It may be necessary to change your telephone service to use this feature. Contact your telephone
company if:
• You have both caller ID and call waiting, but as separate services (you may need combined
service).
• You have only caller ID service, or only caller waiting service.
• You don’t subscribe to any caller ID or call waiting services.
You can use this product with regular caller ID service, and you can use this product’s other features
without subscribing to either caller ID or combined caller ID with call waiting service.
There are fees for caller ID services, and they may not be available in all areas.
This product can provide information only if both you and the caller are in areas offering caller ID
service, and if both telephone companies use compatible equipment.
Caller’s name
*
VTech
Long distance call
L
800-595-9511
AM
5/015:40
PM
Date of call Time of call
20
www.vtechphones.com
NEW
OLD
This party has called
two or more times
Caller’s telephone number
28
Position in call history
Caller ID
About call history (caller ID)
• If you answer a
call before the
caller ID
information
appears on the
screen, it will
not be in the call
history.
Review call history
1. Press (CID) to view call history.
2. Use and to scroll through records in call history.
Delete records from call history
Delete a specific call:
1. Press CID to go to call history mode, then, locate the record by using or to scroll through the
listing.
2. Press DELETE when the record is displayed. You’ll hear a confirmation tone.
Delete all calls:
1.With the handset in idle (off) mode, press and hold DELETE. The screen displays ERASE ALL
NO YES. The current choice flashes.
www.vtechphones.com
21
Basic operation
Your telephone can store up to 30 calls in its caller ID memory. The most recent call will have the
highest number. When the memory is full, the oldest call will be deleted to make room for new incoming
call information. For each incoming call, the screen displays the following information between the
first and second rings:
• Your caller’s name (15 letters are sent by your telephone company).
• The caller’s area code and telephone number.
• The time and date of the call.
• The repeat tag (*) in the upper right corner, indicating the party has called more than once.
Caller ID
•Press OFF at any
time to exit call
history.
• Caller ID numbers
may appear with an
area code that may
not be required to
dial local calls, or
without a 1 that may
be required for long
distance calls. If the
number displayed
is not in the correct
format, press #
repeatedly to see different dialing
options (you can
choose to dial with or without the area code and with or without the 1).
22
2. Press until YES flashes.
3. Press SELECT. There will be a confirmation beep.
Dial a displayed number
1. Press CID to go to call history mode, then locate the record by using �
595-9511
or to search for the desired number.
5/01 5:40PM OLD28
2.If you wish to change how the number will be dialed, press #. The
screen displays alternate dialing sequences available for this call.
3. Press SELECT. Press or until DIAL flashes.
DIAL PROGRAM
800-595-9511
Press SELECT, and you will see the display as shown in the figure
5/01 5:40PM
OLD28
on the right.
4. Press SELECT again. The number is automatically dialed.
-OR When the number is correctly displayed for dialing, press TALK.
Store a call history entry to the directory
1. Locate the record in the call history to be stored in the directory.
2.If you wish to change how the number is stored, press #. The screen
displays alternate dialing sequences available for this call.
3. Press SELECT, then press or until PROGRAM flashes.
4. You can modify the name and the numbers of the record before
saving it in the directory by using the input method mentioned in
www.vtechphones.com
DIAL PROGRAM
800-595-9511
5/01 5:40PM
OLD28
Caller ID
DISTINCT RING? N
800-595-9511
Screen displays:
When:
PRIVATE
The other party is blocking the name and/or number
information.
UNKNOWN
Your telephone company is unable to receive information
about this caller’s name and/or number.
* (after name)
This caller has called more than once.
www.vtechphones.com
Basic operation
Speed Dialing (see pages 13-14).
5. Press SELECT when finished or if you do not need to modify the
record.
6. Press or to select Y or N for distinctive ringer.
7.Press SELECT. There will be a confirmation beep. If you choose Y
in step 6, a D will be displayed with the directory entry.
23
Batteries
Battery care and maintenance
•If you repeatedly get a
low battery indicator,
even after charging
overnight, the battery
should be replaced.
• To reduce the risk of fire
or injury to persons or
damage to the telephone,
charge the battery
provided with or
identified for use with this product only
in accordance with
the instructions and
limitations specified in
the user’s manual.
• Battery power is
consumed whenever the
handset is off the base
unit or charger, even
when the handset is in idle mode.
• Once the battery is
fully charged, it is not
necessary to charge it
again until BATTERY
LOW is displayed or
flashes. This will maximize the battery life.
24
After the battery is fully charged, you can expect the following performance:
Operation
Operating time
While in use (talking)
approximately 225 minutes (3.75 hours)
While not in use (standby*)
approximately 90 hours (3.75 days)
* Handset is off the base unit or charger but not in use.
• The battery needs charging when:
— A new battery is installed in the handset.
— The telephone beeps twice every five seconds.
— The screen displays BATTERY LOW and the low battery icon.
•Place the handset in the base unit. The battery is usually fully charged after 16 hours.
•The battery can be kept fully charged by returning the handset to the base unit after each use.
1
Replace the handset battery
1.Remove the battery compartment cover on the handset by pressing on the indentation and
sliding the cover downward.
2. Lift out the old battery and disconnect.
3.Align the new battery’s plug with the socket pins, and snap the plug into place. Snap the
battery in the compartment, as described in Installing Handset Battery on page 4.
4. Slide the compartment cover back on the handset.
5.The new battery must be charged before using the telephone. Place the handset in the base
unit and allow it to charge for at least 16 hours. The telephone might operate before 16 hours
of charging. However, only fully charged battery can provide the best performance.
www.vtechphones.com
Black
wire
3
Red
wire
Red Black
wire wire
2
1
4
Troubleshooting
If you have difficulty operating your telephone, the suggestions below should solve the problem. If you still have difficulty after
trying these sug­gestions, call VTech Communications at 1(800)595-9511. In Canada, call VTech Telecommunications Canada Ltd.
at 1(800)-267-7377.
Suggestion
My telephone doesn’t
work at all.
• Make sure the power cord is plugged in.
• Make sure the telephone line cord is plugged firmly into the base unit and the telephone wall jack.
• Charge the battery in handset for at least 16 hours before first use. For optimum daily performance,
return the handset to its base unit when not in use.
• Reset the base unit. Unplug the power cord of the base unit. Wait for 15 seconds then plug it back
in. Allow up to one minute for the handset and base unit to reset.
• The telephone may need a new battery, please refer to Installing Handset Battery on page 4 of this
user’s manual.
I cannot get a dial tone.
•
•
•
•
Try all the suggestions above.
Move the handset closer to the base unit. The handset might have moved out of range.
The line cord might be malfunctioning. Try installing a new line cord.
If the previous suggestions do not work, disconnect the base unit from the telephone jack and connect
a working telephone. If there is no dial tone either, the problem is in the wiring or local service. Contact
your local telephone company.
www.vtechphones.com
25
Additional information
Problem
Troubleshooting
Problem
Suggestion
I cannot dial out.
• Make sure there is a dial tone before dialing. The handset may take a second or two to synchronize
with the base unit and produce a dial tone.
• Make sure the telephone is set to the correct dial mode (pulse or touch tone). It should match the dial
mode provided by the telephone company (pulse or touch tone). Refer to the Installation section
(page 7) of this user’s manual to set the dial mode.
• If other telephones in your home are having the same problem, the problem is in the wiring or local
service. Contact your local telephone company (charges may apply).
• Eliminate any background noise. Noise from a television, radio or other electrical appliances may
cause the telephone to not dial out properly. If you cannot eliminate the background noise, try muting
the handset before dialing, or dialing from another room in your home with less background noise.
My handset beeps
four times and isn’t
performing normally.
• Make sure the power cord is securely plugged into the base unit. Plug the power cord into a different
working outlet not controlled by a wall switch.
• Move the handset closer to the base
�����������������������������������������������������
unit��������������������������������������������
. The handset might have moved out of range.
• Reset the base unit. Unplug the power cord. Wait for 15 seconds and plug it back. Allow up to one
minute for the handset and base unit to synchronize.
• Other electronic products can cause interference with your cordless telephone. Try installing it away
from these types of electronic devices: wireless routers, radios, radio towers, pager towers, cellular
telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and
other cordless telephones.
26
www.vtechphones.com
Troubleshooting
Suggestion
CAN’T CONNECT
displays on my
handset.
• Move the handset closer to the base unit. The telephone might have moved out of range.
• Reset the base unit. Unplug the power cord. Wait for 15 seconds and plug it back. Allow up to one
minute for the handset and base unit to reset.
• Other electronic products can cause interference with your cordless telephone. Try installing your
telephone away from these types of electronic devices: wireless routers, radios, radio towers, pager
towers, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen
appliances and other cordless telephones.
The battery does not
hold a charge.
• Make sure the battery is fitted in correctly in the handset.
• Be sure to use the AC power adapter provided with your telephone.
• Charge the battery for at least 16 hours. For optimum daily performance, return the handset to the
base unit when not in use.
•It may be necessary to purchase a new battery, please refer to the section on Installing Handset
Battery on page 4 of this user’s manual.
• The telephone might be malfunctioning. Please refer to the Warranty Statement on page 32 of this
user’s manual.
www.vtechphones.com
27
Additional information
Problem
Troubleshooting
Problem
Suggestion
I get noise, static, or
weak signals even when
I’m near the base unit.
• Press the CHAN button while on a call until the interference has been eliminated.
• Other electronic devices can cause interference with your cordless telephone. Try installing your
telephone away from these types of electronic devices: wireless routers, radios, radio towers, pager
towers, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen
appliances and other cordless telephones.
• Microwave ovens operate on the same frequency as your telephone. It is normal to experience static
on your telephone while the microwave oven is in operation. Do not install this telephone in the same
outlet or near the microwave oven.
•If your telephone is plugged in with a modem or surge protector, plug the telephone (or modem/surge
protector) into a different location. If the problem is solved, have your telephone moved away from
the modem until there is no static or noise, or use a different surge protector.
• Relocate your telephone to a higher location. The telephone will likely get better reception when
installed in a higher location.
• If other telephones in your home are having the same problems, the problem is in the wiring or local
service. Contact your local telephone company (charges may apply).
I hear noise in the
handset, and none of the
keys or buttons work.
• Make sure the power cord is plugged in.
28
www.vtechphones.com
Troubleshooting
Suggestion
I hear other calls while
using my telephone.
• Disconnect the base unit from the telephone jack, and plug in a regular telephone. If you still
hear other calls, the problem is probably in the wiring or local ser vice. Contact your local
telephone company.
My handset does not ring
when I receive a call.
• Make sure the ringer is activated. Refer to the section(s) on ringer selection in this user’s manual.
•Make sure the telephone line cord is plugged firmly into the base unit and the telephone jack. Make sure
the power cord is plugged in.
• The handset may be too far from the base unit.
• Charge the battery in the handset for at least 16 hours. For optimum daily performance, return the handset
to the base unit when not in use.
• There may be too many extension telephones on your telephone line for all of them to ring. Try unplugging
some of the other telephones.
• The layout of your home or office might be limiting the operating range. Try moving the telephone base to
another location, preferably on an upper floor.
• If other telephones in your home are having the same problem, the problem is in the wiring or local service.
Contact your local telephone company (charges may apply).
• Test a working telephone at the telephone jack. If another telephone has the same problem, the problem
is the telephone jack. Contact your local telephone company (charges may apply).
• Other electronic devices can cause interference with your cordless telephone. Try installing your telephone
as far away as possible from these types of electronic devices: wireless routers, radios, radio towers, pager
towers, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances
and other cordless telephones.
• The telephone line cord might be malfunctioning. Try installing a new line telephone cord.
www.vtechphones.com
29
Additional information
Problem
Troubleshooting
Problem
Suggestion
My calls fade in and
out while I’m using my
handset.
• Press the CHAN button while on a call until the interference has been eliminated.
•Other electronic devices can cause interference with your cordless telephone. Try installing your
telephone away from these types of electronic devices: wireless routers, radios, radio towers, pager
towers, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen
appliances and other cordless telephones
•Microwave ovens operate on the same frequency as your telephone. It is normal to experience static
on your telephone while the microwave oven is in operation. Do not install the telephone near the
microwave oven or in the same outlet.
• If your telephone is plugged in with a modem or surge protector, plug the telephone (or modem/surge
protector) into a different location. If the problem is solved, put your telephone away from the modem
until there is no static or noise, or use a different surge protector.
• Relocate your telephone to a higher location. The telephone will get better reception when installed
in a higher area.
• If other telephones in your home are having the same problem, the problem is in your wiring or local
service. Contact your local telephone company (charges may apply.)
The caller ID isn’t
working.
• Caller ID is a subscription service. You must subscribe to this service for this feature to work on your
telephone.
• The caller must be calling from an area that supports caller ID.
• Both you and your caller’s telephone companies must use caller ID compatible equipment.
30
www.vtechphones.com
Troubleshooting
Problem
Suggestion
Common cures for electronic equipment.
If the base unit does not seem to be responding normally, try putting the handset in the base
�����������������
unit��������
. If it
still does not respond, do the following (in the order listed):
1. Disconnect the power to the ����������
base unit�.
2. Disconnect the handset battery, and spare battery, if applicable.
3. Wait for a few minutes.
4. Connect power to the base
����������
unit�.
5. Re-install the battery.
6. Wait for the handset to synchronize with the base
�������������������������������������������������������
unit����������������������������������������������
. To be safe, allow up to one minute for this
to take place.
If you subscribe to DSL service:
To single telephone jack
(RJ11C)
Telephone line cord
Noise filter
(For DSL users)
www.vtechphones.com
31
Additional information
If you hear noise during conversations and/or your caller
ID features are not functioning properly, install a noise
filter to the telephone line between the base unit and
the telephone line jack. Contact your DSL provider to
obtain a noise filter.
Maintenance
Taking care of your telephone.
Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect your telephone if you need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset outdoor in the rain, or handle it with wet hands. Do not install your base unit near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety, exercise caution when using electric appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic case that should retain its luster for many years. Clean it only with a soft cloth slightly dampened with water or mild soap. Do not use excess water or cleaning
solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you are wet or standing in water. If your base unit should fall into water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL. Then, pull the base unit out by the unplugged cords.
Warranty
What does this limited warranty cover?
• The manufacturer of this VTech product, VTech Communications, warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the product and all accessories provided by
VTech in the sales package (“Product”) are free from material defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in
accordance with operation instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America.
What will VTech Communications do if the Product is not free from material defects in materials and workmanship during the limited warranty period (“Materially Defective
Product”)?
• During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without charge, a Materially Defective Product. If we repair this product,
we may use new or refurbished replacement parts. If we choose to replace this product, we may replace it with a new or refurbished product of the same or similar design. VTech will return
repaired or replacement products to you in working condition. VTech will retain defective parts, modules, or equipment. Repair or replacement of Product, at VTech’s option, is your exclusive
remedy. You should expect the repair or replacement to take approximately 30 days.
How long is the limited warranty period?
• The limited warranty period for the product extends for ONE (1) YEAR from the date of purchase if we repair or replace a Materially Defective Product under the terms of this limited warranty.
This limited warranty also applies to repaired or replacement Products for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time
remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid
32
www.vtechphones.com
Warranty
State Law Rights: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
imitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the product is fit for ordinary use) are limited to one year from date
L
of purchase. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
•
In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the product, or other
associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this product. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
www.vtechphones.com
33
Additional information
intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or
3.Product to the extent that the problem experienced is caused by signal conditions, network reliability or cable or antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech electrical accessories; or
5.Product whose warranty/quality stickers, Product serial numbers’ plates or electronic serial numbers have been removed, altered or rendered illegible; or
6.Product purchased, used, serviced, or shipped for repair from outside the United States, or used for commercial or institutional purposes (including but not limited to Products used for rental
purposes ); or
7. Product returned without valid proof of purchase (see 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.
How do you get warranty service?
•
To obtain warranty service in the United States of America, call 1(800)595-9511 for instructions regarding where to return the Product. Before calling for service, please check the user’s
manual. A check of the Product controls and features may save you a service call.
•
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport
of Product(s) to the service location. VTech will return repaired or replaced product under this limited warranty to you, transportation, delivery or handling charges prepaid. VTech assumes
no risk for damage or loss of the Product in transit.
•
If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the
cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty;
2. Include “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other Limitations
•This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other
warranties for this product. The warranty exclusively describes all of VTech’s responsibilities regarding the product. There are no other express warranties. No one is authorized to make
modifications to this limited warranty and you should not rely on any such modification.
Important safety instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3.Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water (for example, near a bath tub, kitchen sink or swimming pool).
5.Do not place this product on an unstable surface, such as a table, shelf or stand. The product may fall, causing serious damage.
6.Slots and openings in the back or bottom of the base unit and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the
product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper
ventilation is not provided.
7.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local
power company.
8.Do not allow anything to rest on the power cord. Do not install this product where the cord may have anyone walking on it.
9.Never push objects of any kind into this product through slots in the base or handset as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric
shock. Never spill liquid of any kind on the product.
10. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the base or handset other than specified
access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.
11. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
12.Unplug this product from the wall outlet and refer servicing to an authorized service facility under the
following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled onto the product.
C. If the product has been exposed to rain or water.
D.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of
other controls may result in damage and often requires extensive work by an authorized technician to restore the product to normal operation.
E.If the product has been dropped and the base and/or handset has been damaged.
F. If the product exhibits a distinct change in performance.
13.Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock from lightning.
14. Do not use the telephone to report a gas leak in the vicinity of the leak.
15. Only put the handset of your telephone next to your ear when it is in normal talk.
34
www.vtechphones.com
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements
are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product.
This product has been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The base unit shall be installed and used such that parts of the user’s
body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more. If you choose to use a clipping device, please make sure to only use the supplied VTech belt clip.
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this
equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your local telephone company upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant
telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack should normally be used for connecting
to a single line and an RJ14 jack for two lines. See Installation Instructions in the user’s manual.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your
alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its
authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty.
If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your telephone service. The telephone company is required to notify you before inter-
www.vtechphones.com
35
Additional information
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is
encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more
information, please contact your local telephone company.
FCC, ACTA and IC regulations
rupting service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem and the telephone company is required to inform you
of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this product.
The telephone company is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:
• Remain on the line and briefly explain the reason for the call before hanging up.
• Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
This equipment complies with regulations RSS210 and CS-03 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
The term “IC:” before the certification/registration number only signifies that the Industry Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination
on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five.
36
www.vtechphones.com
The RBRC® seal
The RBRC® seal
The RBRC® seal on the nickel-cadmium battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and
recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada.
The RBRC® program provides a convenient alternative to placing used nickel-cadmium batteries into the trash or municipal waste, which may be illegal in
your area.
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers participating in the RBRC® program or at authorized VTech product
service centers. Please call 1(800) 8BATTERY™ for information on ni-cd battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this
program is part of its commitment to protecting our environment and conserving natural resources.
RBRC® is a registered trademark of Rechargeable Battery Recycling Corporation.
37
Additional information
www.vtechphones.com
Technical specifications
Enhanced 2.4GHz technology–your telephone operates on a dual band transmission that combines the best of 2.4GHz and 900MHz
technologies, providing enhanced performance over standard cordless telephones.
Frequency control
Crystal controlled
PLL synthesizer
Transmit frequency
Base: 2410.2–2418.9 MHz
Handset: 912.75–917.10 MHz
Receive frequency
Base: 912.75–917.10 MHz
Handset: 2410.2–2418.9 MHz
Channels
30
Nominal effective range
Maximum power allowed by FCC and IC. Actual operating range may vary according to
environmental conditions at the time of use.
Size
Handset: 185.5mm X 53.4mm X 39.0mm
Base: 88.8mm X 107.5mm X 122.7mm
Weight
Handset: 116 grams
Base: 133.2 grams
Power requirements
Handset: 3.6V 300mAH Ni-Cd battery
Base: 9V AC @ 250mA
Memory
Speed dial: 9 Memory locations, 24 digits per location
Directory: 10 Memory locations, 24 digits per location
Caller ID: 30 Memory locations
38
www.vtechphones.com
Index
A
Additional information 25–38
B
Basic operation 9–24
Batteries 24
Battery care and maintenance 24
Before you begin 3
C
Dial mode 7
Directory 16-19
DSL Service 5, 31
E
Edit a number/name in speed dial 15
Edit a number/name in the directory 17
F
FCC, ACTA and IC regulations 35–36
Caller ID operation 20–23
Charge the handset battery 6
Check for dial tone 7
Choose a location 4
G
D
Handset operation 9
Delete a number/name in speed dial 15
Delete a number/name in the directory 17
Delete records from call history 21
Dial a displayed number 22
Dial a number from the directory 18
Dial a speed dial number 15
Getting started 3–8
H
I
Important safety instructions 34
Installation 4–8
Install handset battery 4
Internet 5, 31
www.vtechphones.com
39
Index
L
Language 6
M
Maintenance 32
Message waiting 8
Move a number/name to memory 19
O
Operating range 11
P
Speed dial 13–15
Store a call history entry to the directory 22
Store a number/name in speed dial 13
Store a number/name in the directory 16
T
Table/desk installation 5
Technical specifications 38
Telephone base operation 10
Telephone operation 9–12
Temporary Tone Dialing 11
Troubleshooting 25–31
Parts checklist 3
W
R
Wall Mounting 5
Warranty Statement 32
Reassign locations in speed dial 15
Replace the handset battery 24
Review call history 21
S
Set handset date and time 6
Set the ringer 7
40
www.vtechphones.com
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES.
Distributed in the U.S.A. by VTech Communications, Inc. Beaverton, Oregon
Distributed in Canada by VTech Telecommunications Canada, Ltd., Richmond, B.C.
Copyright ©2006 for VTECH TELECOMMUNICATIONS LTD.
Printed in China.
91-000859-010-000
User’s Manual
www.vtechphones.com
Model: t2326
Download PDF