falcon - Downloads
FA L CON
WORLD CLASS SE CURITY
FALCON PREDATOR XL2
Vehicle Security System with Anti-Hijack
Installer’s Manual
HELPLINE: 0906 700 10 20
(All calls charged at 50p/min)
Falcon Security Ltd. Unit 9 Tanning Court, Warrington, Cheshire, WA1 2HF, UK
Internet: http://www.falcon-security.com Email: [email protected]
112005
FA L CON
WORLD CLASS SE CURITY
FALCON PREDATOR XL2
Vehicle Security System with Anti-Hijack
Installer’s Manual
01. System Status Memory ............................................. 2
02. Operation of the Remote Control................................. 2
03. Basic Functions ........................................................ 2
REMOTE ARM ........................................................ 2
REMOTE DISARM .................................................... 2
SILENT ARM ......................................................... 3
SILENT DISARM ..................................................... 3
TRIGGER MEMORY - LED INDICATOR ............................ 3
SYSTEM STATUS - LED INDICATOR .............................. 3
CLEAR THE TRIGGERS AND SYSTEM ALARMING.................. 3
TRIGGER AND THE SYSTEM ALARMING ........................... 3
PANIC MODE ........................................................ 4
EMERGENCY OVERRIDE ............................................. 4
VALET MODE ........................................................ 4
CAR FINDER ......................................................... 4
SHOCK SENSOR TEMPORARY BYPASS ............................ 4
MANUAL ARMING ................................................... 5
04.
05.
06.
07.
08.
09.
Code Learning of Remote Control ................................ 5
Programming Option Features .................................... 5
Option Features Table ............................................... 6
Explanation of Option Features ................................... 7
Wiring Diagram ...................................................... 12
Wiring Diagram of 2 Stage Door Unlocks .................... 13
01. System Status Memory
The system will enter the same mode after powering on as when it was powered off.
02. Operation of the Remote Control
BUTTON
BTN#1 once
BTN#2 once
BTN#1 3sec.
BTN#3 2sec.
BTN#4 once
BTN#1+2 once
BTN#3 then #1
ARMED
ARM
DISARM
PANIC
BOOT RELEASE
CAR FINDER
SILENT DISARM
CH3
DISARMED
ARM
DISARM
PANIC
BOOT RELEASE
CAR FINDER
SILENT ARM
CH3
IGNITION ON
DOOR LOCK
DOOR UNLOCK
BOOT RELEASE
ANTI HIJACK
CH3
03. Basic Functions
Remote Arm
With the system disarmed and ignition off, press button #1 once, the siren will chirp once and the hazard lights flash
once to confirm entering the arm mode.
*The siren will not chirp if programming the Option Features item #1 OFF.
Remote Disarm
Pressing button #2 once with system armed will disarm the system and the siren will chirp twice and the hazard lights
flash twice to confirm the alarm is disarmed. The siren will chirp 4 times if the system has been triggered during the
arm mode.
- 2 -- 2
Silent Arm
Pressing buttons #1+2 once with system disarmed and ignition off will arm the system without siren chirp.
Silent Disarm
Pressing buttons #1+2 once with system armed will disarm the system without siren chirp. The siren will still chirp 4
times if the system has been triggered before disarming.
Trigger Memory - LED Indicator
When disarming, if the system was triggered whilst armed the siren will chirp 4 times, hazard lights flash 2 times and
the LED will flash to indicate the triggered zone as follows:
1 flash
=
Shock Sensor 2nd stage trigger
2 flashes
=
Bonnet Trigger
3 flashes
=
Door Trigger
4 flashes
=
Ignition Trigger
System Status - LED Indicator
No Light
=
Disarm
Slow Flash
=
Arm
Fast Flash
=
Auto Rearm/Passive Arming/Anti-hijacking
Steady Light
=
Valet Mode
Clear the Triggers and System Alarming
When the system is triggered the hazard lights will flash and the siren will sound the cycle duration as per the setting
of option feature #14.
Press button #1:
When the system is triggered with the siren sounding and hazard lights flashing, press button #1 once and the siren
and hazard lights will both stop and then:
-
The
The
The
The
The
siren will chirp once
hazard lights will flash once
doors will lock (if connected)
LED will flash to indicate the triggered zone
system will remain in the armed mode.
Press button #2:
When the system is triggered with the siren sounding and hazard lights flashing, press button #2 once, the siren and
hazard lights will both stop and then:
-
The
The
The
The
The
siren will chirp 4 times
hazard lights will flash twice
doors will unlock (if connected)
LED will flash to indicate the triggered zone
system will enter disarmed mode
By override mode:
If the remote control doesn’t work properly then overriding the system will clear the trigger and disarm the system.
Trigger and the System Alarming
The system will respond as follows if the system is triggered under armed mode: (When the system is triggered, the
siren sounding cycle will be 30sec., 60sec. or 8 cycles of 30sec. depending on the setting of Option features #14)
Shock sensor 1st stage triggered:
Light impact will activate the 1st stage of the shock sensor and the siren will chip 3 times to warn. If Option Feature #2
is programmed as ‘FIRST’ then the shock sensors 1st stage will be bypassed after 3 consecutive triggers until the
system is disarmed and armed again.
Shock sensor 2nd stage triggered:
Heavy impact will activate the 2nd stage of the shock sensor. The siren will sound and the hazard lights will flash for
one cycle. If Option Feature #2 has been selected as ‘BOTH’ then the 1st and 2nd stage of the shock sensor will be
bypassed after each stage has been triggered 3 times continually until the system is disarmed and armed again.
Bonnet opened and then closed:
The siren will sound and the hazard lights will flash for one cycle.
Bonnet opened and not closed:
The siren will sound and the hazard lights will flash for 3 cycles and the bonnet switch will be bypassed until it is closed.
Door opened and then closed:
- 3 -- 3
The siren will sound and the hazard lights will flash for one cycle.
Door opened and not closed:
The siren will sound and the hazard lights will flash for 3 cycles and then the door input will be bypassed until all doors
are closed.
Ignition Acc. turns on and then off:
The siren will sound and hazard lights will flash for one cycle.
Ignition Acc. turns on and not off:
The siren will sound and the hazard lights will flash for 3 cycles and then the Ignition Acc. will be bypassed until it is
turned off again.
Panic Mode
With the system armed:
Press button #1 for 3 seconds and the siren will sound and hazard lights flash for one cycle. The system will remain
armed.
With the system disarmed:
Press button #1 for 3 seconds and the system will arm and then the siren will sound and the hazard lights will flash for
one cycle. The system will remain armed.
*During the panic mode, pressing button #1(#2) will
interrupt the panic mode and arm (disarm) the system.
Emergency Override
Follow the steps as below to override the system:
- With the system armed or alarming
- Turn the ignition on (or off then on)
- After 2 sec. the LED will flash 10 times slowly
- Press the valet switch once after the LED flashes a number of times equal to the PIN
- The system will be overridden and enter disarm mode
* Repeat the steps from turning the ignition on if the previous operation is failed
* Wait for 3 minutes and operate the override procedure again after 3 times of incorrect operation
* The PIN will be required for overriding the system the following situations:
1. If the remote control doesn’t work
2. To deactivate the anti-hijacking
3. To deactivate the Entry Delay(option features #12)
4. To deactivate the AED(option features #9)
Valet Mode
Valet mode is a convenient feature to use when you hand the remotes to third person for valet parking or vehicle
service and the operation is as follows:
*
*
*
With the system disarmed
Turn the ignition on
Within 10 seconds press the valet switch for 2 seconds
The LED will turn on
The system enters the valet mode
To exit valet mode repeat the steps above again, the LED will be turned off to confirm leaving the valet mode.
Under valet mode and with the ignition off, pressing buttons #1 and #2 will be still lock and unlock the doors.
The anti-hijacking will not be activated with the system valet mode.
Car Finder
The Car Finder function will work with the system armed or disarmed but the ignition must be off. The operation is as
follows:
-
Press button #4 once:
The hazard lights will flash 6 times
Press and hold button #4 and 2 seconds later:
The hazard lights will flash and the siren will chirp till button #4 is released.
Shock Sensor Temporary Bypass
Press Button #1 again within 2 seconds of pressing button #1 to arm the system, the shock sensor will be bypassed
until the next arming of the system.
- 4 -- 4
Manual Arming
To arm the system without the remote the operation is as follows:
-
With the system disarmed
The ignition is off
Press the valet switch for 3 seconds
Hazard lights flash once and LED will flash rapidly
30 seconds later, the system will be armed automatically but the doors will not be locked
04. Programming a new Remote Control
- Start with the system disarmed
- Turn the ignition on
- Within 10 seconds press valet switch 3 times
- After 2 seconds the siren will sound for 2 secs to confirm the system is now in code learning mode
- Within 10 seconds press any key of the remote control, the siren will sound for 1 sec and the hazard lights will
flash twice to confirm the remote control has been programmed to the system. All the previous codes in the
system will be erased entirely so you must now program your second remote control.
- Within the next 10 secs press any key of 2nd remote control to program the 2nd remote control to the system, the
siren will sound for 1sec and hazard lights flash twice to confirm.
- The system will leave the code learning mode automatically after programming the 2 remote control to the system
and the siren will sound for 2 seconds to confirm.
- The system will leave the code learning mode at any time if the ignition off is turned off.
- The system will leave the code learning mode if a remote control button is not pressed within 10 secs.
05. Programming Optional Features
Follow the steps as below to program the option features:
- Start with the system disarmed
- Turn the ignition on and then off
- Within 10 seconds press the valet switch 3 times
- The siren will sound for 2 seconds to confirm the system has entered the programming mode
- Within 10 seconds press button #1 the same number of times as the number of the feature you wish to program.
The siren will chirp once for each press of button #1.
To Reset to Factory Default:
Within 10 seconds press button #4 for 3 seconds and all the programmable features will be reset to the factory
default. The siren will sound for 2 seconds to confirm leaving the programming mode
- After selecting the programmed item, press button #2 once, the siren will chirp the same number of times as the
feature you selected to confirm your selection
- Press button #1, #2 or #3 to program the feature as desired, the siren will respond with 1, 2 or 3 chirps to
confirm the setting. Then turn the ignition on and the siren will sound for 2 seconds to confirm leaving
programming mode. (if you don’t turn the ignition on the system will leave the programming mode automatically
10 seconds later)
- Repeat the above steps from turning the ignition on and off to program the next feature
* The system will leave the programming mode automatically if no buttons are pressed within 10 seconds or if the
ignition is turned on.
Re: #26 PIN - Personal Identification Number
Follow the steps as below to program the item #26 PIN:
- Start with the system disarmed
- Turn the ignition on and then off
- Within 10seconds press the valet switch 3 times
- The siren will sound for 2 seconds to confirm the system has entered the programming mode
- Within 10 seconds press button #1 26 times and then press button #2 once, the siren will chirp 26 times to
confirm that item #26 has been selected
- After 2 seconds the LED will start to flash 10 times slowly
- Press button #1 after the LED has flashed the number of times you want to set the PIN to. E.g. If you want to
choose 6 as the personal code then press button #1 once after the LED has flashed 6 times. The LED will turn off
to confirm leaving the programming mode.
* Program the next feature from turning the ignition on and then off
* If button #1 is not pressed to choose the new PIN then the previous PIN will be still valid
- 5 -- 5
06. Option Features Table: (*Factory Default=1 CHIRP - Button#1/#2/#3 = 1/2/3 CHIRP)
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
CHIRP
1 CHIRP
2 CHIRP
3 CHIRP
4 CHIRP
5 CHIRP
6 CHIRP
7 CHIRP
8 CHIRP
9 CHIRP
10 CHIRP
11 CHIRP
12 CHIRP
13 CHIRP
14 CHIRP
15 CHIRP
16 CHIRP
17 CHIRP
18 CHIRP
19 CHIRP
20 CHIRP
21 CHIRP
22 CHIRP
23 CHIRP
24 CHIRP
25 CHIRP
26 CHIRP
FUNCTION
CHIRP ON/OFF
SHOCK SENSOR BYPASS
DOOR LOCK TIME
DOOR UNLOCK TIME
IGNITION LOCK
IGNITION UNLOCK
DOOR UNLOCK WITH DISARMING
AUTO REARM
AUTOMATIC ENGINE DISABLE(AED)
PASSIVE/LAST DOOR ARMING
DOOR LOCK WITH PASSIVE/LAST DOOR ARMING
ENTRY DELAY
INTERIOR LIGHT DELAY
ALARM CONDITION CYCLE DURATION
IMMOBILISER RELAY
DOOR OPEN ALERT
DISARM WITH BOOT RELEASE
BYPASS INPUT WIRE
COMFORT CLOSURE(CH3)
PAGER OUTPUT
ANTI HIJACKING DELAY
ANTI HIJACKING BY REMOTES
ANTI HIJACKING BY IGNITION ON + DOOR OPEN
ANTI HIJACKING BY IGNITION
ANTI HIJACKING BY PRESSING VALET SWITCH
PIN - PERSONAL IDENTIFICATION NUMBER
3 1 CHIRP
ON
DISABLE
1 PULSE
1 PULSE
DISABLE
DISABLE
DRIVER
DISABLE
DISABLE
DISABLE
DISABLE
DISABLE
DISABLE
30 SEC
ARM
DISABLE
DISABLE
DISABLE
DISABLE
5 SEC
15 SEC
DISABLE
DISABLE
DISABLE
DISABLE
1 PRESS
3
2 CHIRP 3 3 CHIRP
OFF
FIRST
BOTH
2 PULSE
4 SEC
2 PULSE
4 SEC
ENABLE
DRIVER
ALL
ALL
ENABLE
ENABLE
ENABLE
ENABLE
ENABLE
15 SEC
40 SEC
60 SEC
8 CYCLES
DISARM
ENABLE
ENABLE
ENABLE
ENABLE
10 SEC
15 SEC
30 SEC
60 SEC
ENABLE
ENABLE
ENABLE
ENABLE
2~10 PRESS
07. Explanation of Optional Features
#1 Chirp Confirmation
When Set as On
When arming the system the siren will chirp once.
When disarming the system the siren will chirp twice.
When Set as Off
The siren will not chirp when arming or disarming the system but the siren will still chirp 3 times if a door or the
bonnet is not closed properly when arming and the siren would chirp 4 times when disarming if the system has been
triggered.
#2 Shock Sensor Bypass
When Set as Disabled
The 1st and 2nd stages of shock sensor will work normally all the time.
When Set as First
The shock sensor 1st stage will be bypassed after 3 consecutive triggers until the system is disarmed and armed again.
When Set as Both
The 1st and 2nd stage of shock sensor would be bypassed if each stage has had 3 consecutive triggers until the system is
disarmed and armed again.
#3 Door Lock Time
When Set as 1 Pulse
The system will send 1 x 1 second pulse when locking the doors.
When Set as 2 Pulse
The system will send 2 x 1 second pulse when locking the doors.
When Set as 4sec.
The system will send 1 x 4 second pulse when locking the doors.
#4 Door Unlock Time
When Set as 1 Pulse
The system will send 1 x 1 second pulse when unlocking the doors.
When Set as 2 Pulse
The system will send 2 x 1 second pulse when unlocking the doors.
When Set as 4sec.
The system will send 1 x 4 second pulse when unlocking the doors.
#5 Ignition Lock
When Set as Enabled
With the system disarmed the doors will be locked 3 seconds after turning the ignition on unless a door is still open.
The doors will be locked again automatically after stepping on the brake pedal if the door is opened and closed again
during driving.
#6 Ignition Unlock
When Set as Driver
After parking the car the drivers door will be unlocked after turning the ignition off.
When Set as All
After parking the car all the doors will be unlocked after turning the ignition off.
#7 Door Unlock with Disarming
When Set as Driver
Only the drivers door will be unlocked when pressing the unlock button (#2) to disarm the system. Pressing button
#2 again within 3 seconds will unlock the rest of the doors.
When Set as All
All the doors will be unlocked when pressing the unlock button (#2) to disarm the system.
#8 Auto Rearm
When Set as Enable
The system will be armed again automatically 30 seconds after disarming the system by remote if no doors are opened.
Opening a door after disarming the system will deactivate the Auto rearm feature.
- 7 -- 7
During the 30 second wait the LED will flash to indicate the triggered zone if the system was triggered whilst armed.
#9 Automatic Engine Disable (AED)
When Set as Enable
After parking the car, turning the ignition off and opening and then closing the door the immobiliser will activate
within 10 seconds.
-
The immobiliser will not be active during the 10 second countdown.
After 10 seconds the PIN will be required to disable this feature
With this feature on the system will still be able to enter the arm mode by pressing the remote, via passive/last
door arming or using Manual Arming
When disarming the system, the AED will still be on and have to deactivated by PIN as follows:
*Disarm the system by remote
*Turn the ignition on
*The LED will flash 10 times slowly after 2 seconds.
* Press the valet switch once after the LED flashes a number of times equal to the PIN
#10 Passive/Last Door Arming
When Set as Enable
The LED will flash rapidly and the system will automatically be armed 30 seconds after closing the last open door,
bonnet and boot properly. The siren will chirp and hazard lights flash once to confirm.
The 30 second countdown will be temporarily interrupted if any of the doors, boot or bonnet are opened. The
countdown will restart once all doors/boot/bonnet are closed.
#11 Door Locks with Passive/Last Door Arming
When Set as Enable
The doors will also be locked when the passive/last door arming feature is activated.
#12 Entry Delay
When Set as Enable
Triggering of the system will be delayed by 30 seconds when opening the door with the key. After 30 seconds the siren
will chirp 10 times to warn and then the system will alarm.
During the 30 second countdown and the 10 warning chirps, the Entry Delay feature still can be deactivated by override
or by pressing the disarm button of remote to disarm the system.
#13 Interior Light Delay
When Set as Disable
The siren will chirp 3 times to warn if a door is not closed properly when arming the system. The doors will not be
protected by the system until all the doors are closed properly. All the other protection zones will be operational.
When Set as 15sec. (or 40sec)
The siren will chirp once and the hazard lights flash once when the system is armed. 15 seconds (or 40sec) later, the
siren will chirp 3 times to warn if a door is not closed properly. The doors will not be protected by the system until all
the doors are closed properly. All the other protection zones will be operational.
#14 Alarm Condition Cycle Duration
When Set as 30sec. (or 60sec.)
The siren will sound for 30 seconds (or 60sec) x 1 cycle when the system is triggered and released and the siren will
sound for 30 seconds (or 60sec) x 3 cycles if the system is triggered all the time.
When Set as 8 cycles
The siren will sound 30 seconds x 8 cycles regardless of whether the system is triggered and released or triggered all
the time.
#15 Starter Disable Relay
When Set as Arm
The immobiliser relay will be on with the system armed and should be wired as follows:
- 8 -- 8
When Set as Disarm
The immobiliser relay will be on with the system disarmed and should be wired as follows:
*In this case, please wire the shock sensor and any additional sensors as follows:
#16 Door Open Alert
When Set as Enable
If the door is opened when the ignition is on then the hazard lights will flash until the door is closed or the ignition is
turned off.
*When Setting #23 and #24 as Enable the anti-hijacking will have the priority and Door Open Alert feature will not be
functional.
#17 Disarm with Boot Release
When Set as Disable
When operating the remote boot release the system will remain armed but the shock sensor will be bypassed.
boot will be protected and shock sensor reactivated 3 seconds after closing the boot again.
The
When Set as Enable
The system will be disarmed when operating the boot release and the siren will chirp twice and hazard lights flash
twice to confirm.
The countdown of Auto Rearm or Passive/Last Door Arming will be interrupted if the boot release is operated
regardless of whether this feature is Disabled or Enabled. The countdown will be restarted once the boot is closed
again.
#18 Bypass Input Wire
This wire is for use with external Turbo Timer or Remote Engine Start modules.
When Set as Enable
When a negative pulse is connected to this wire with the system armed, the shock sensor, ignition protection and
immobiliser relay will be bypassed until the negative pulse disappears.
- 9 -- 9
#19 Comfort Closure/Total Closure (CH3)
The CH3 wire is designed for the option of automatically closing the windows when arming the system.
When Set as Enable
When arming the system the CH3 will send a 30 second pulse to a window closure module for closing the windows
automatically. In this case the shock sensor will work as normal after the 30 seconds has elapsed. Pressing the
remote to disarm the system during the 30 seconds will deactivate the CH3 30 second output immediately.
When Set as Disable
The CH3 will not be activated when arming the system but can be controlled as follows:
- With system armed or disarmed
- Press button #3 once then press and hold button #1
- After 1 second the CH3 output will be activated until button #1 is released.
#20 Pager Output
When Set as 5-10-15sec.
A 5, 10 or 15 second trigger signal will be sent when the system is triggered and again when the siren starts its next
alarming cycle.
#21 Anti-hijacking Delay
When Set as 15-30-60sec.
After activating the anti-hijacking feature the system will delay entering anti-hijacking mode for 15, 30 or 60 seconds
depending on the selection. The siren will chirp 10 times before entering into the anti-hijacking mode as a last
warning.
#22 Anti-hijacking by Remote
When Set as Enable
The operation is as follows:
- With the system disarmed and ignition on
- Press button #1+2 once
- Hazard lights flash twice to confirm activating anti-hijacking
- After a delay of 15, 30, 60sec.(depends on the selection)
- The siren will chirp 10 times and then
- The system will go into alarm with the siren sounding and hazard lights flashing and the doors will be locked
* Under anti-hijacking mode, the system will not be allowed to enter Valet mode.
* During the anti-hijacking, the immobiliser relay will not activate until the ignition is turned off
* To deactivate anti-hijack once triggered follow the emergency override procedure described in section 3.
#23 Anti-hijacking by Ignition on + Door Open
When Set as Enable
The operation is as follows:
- With the system disarmed and ignition on
- Opening the door will activate anti-hijacking
- Hazard lights flash twice to confirm activating anti-hijacking
- After a delay of 15, 30, 60sec.(depends on the selection)
- The siren will chirp 10 times and then
- The system will go into alarm with the siren sounding and hazard lights flashing and the doors will be locked
* Under anti-hijacking mode, the system will not be allowed to enter Valet mode.
* During the anti-hijacking, the immobiliser relay will not activate until the ignition is turned off
* To deactivate anti-hijack once triggered follow the emergency override procedure described in section 3.
#24 Anti-hijacking by Ignition On
When Set as Enable
The operation is as follows:
- With the system disarmed
- Turn the ignition on will activate anti-hijacking in 10sec. later
- Hazard lights flash twice to confirm activating anti-hijacking
- After a delay of 15, 30, 60sec.(depends on the selection)
- The siren will chirp 10 times and then
- The system will go into alarm with the siren sounding and hazard lights flashing and the doors will be locked
* Under anti-hijacking mode, the system will not be allowed to enter Valet mode.
* During the anti-hijacking, the immobiliser relay will not activate until the ignition is turned off
* To deactivate anti-hijack once triggered follow the emergency override procedure described in section 3.
- 10 -- 10
#25 Anti-hijacking by Pressing Valet Switch
When Set as Enable
The operation is as follows:
- With the system disarmed
- Press the valet switch with the ignition off (or press the valet switch within 10 seconds of turning the ignition on)
- Hazard lights flash twice to confirm activating anti-hijacking
- After a delay of 15, 30, 60sec.(depends on the selection)
- The siren will chirp 10 times and then
- The system will go into alarm with the siren sounding and hazard lights flashing and the doors will be locked
* Under anti-hijacking mode, the system will not be allowed to enter Valet mode.
* During the anti-hijacking, the immobiliser relay will not activate until the ignition is turned off
* To deactivate anti-hijack once triggered follow the emergency override procedure described in section 3.
#26 PIN - Personal Identification Number
* The factory default PIN is 1 press
* Follow the sec. 05. Programming Option Features to change the PIN
- 11 -- 11
08. Wiring Diagram
- 12 -- 12
09. Wiring Diagram of 2 Stage Door Unlocks
- 13 -- 13
- 14 -- 14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement