3. Now attach the 6-position trimming guide. Adjust it to a fairly long trimming length and begin trimming your mustache, starting at the top and working down to your upper lip, using slow, methodical strokes. Use progressively closer settings to get the look and TRIMMING AND EDGING YOUR BEARD length you desire. The following are suggested trimming steps and trimmer 4. For tapering the mustache, hold the positions. You may find different procedures work better for trimmer with the blades pointing you. 1. Comb your beard in the direction that it grows to help reveal upward. Set the trimming guide at a medium length. Starting in the middle of stray hairs that may be longer than the others. your mustache, taper with short upward 2. Attach the multi-position trimming guide to trim and taper your beard. Begin with the guide set at a long trimming length. strokes, working out toward the corners until a gentle shape is created on the Trim toward your chin in smooth, 9854, 9855, 9860 bottom of your mustache. overlapping strokes, following the #1 Stubble Length (2 mm) 5. As a finishing step, remove the lay of your beard to avoid patchy #2 Short (4 mm) #3 Medium Short (6 mm) trimming guide, replace the head so the results. If you trim against the way #4 Medium (8 mm) detail blade, and make a definitive line your beard naturally lays, the #5 Medium Long (10 mm) at the bottom of your mustache. trimmer will cut the hair much #6 Long (12 mm) BODY SCAPING shorter. Adjust the trimming guide to Your trimmer makes for the perfect tool progressively shorter settings until 9877 to groom areas below the neck. Using you reach the desired length of Guide Resulting the same technique, as mentioned prior, beard. You may wish to set the Position Beard Length you can groom wherever you feel a trimming guide attachment to cut No. Inches MM 1 .058 1.47 need. closer near the ear and down under 2 .102 2.59 TRIMMING WITH ATTACHMENT the chin, changing to a longer setting 3 .146 3.71 4 .190 4.83 COMBS toward the front of the face and point 5 .234 5.94 6 .278 7.06 Your trimmer includes three trimming of your chin. When the trimming 7 8.18 .322 attachments; stubble, medium and long. guide is removed, it will remain at its 8 .366 9.30 9 .410 10.41 The stubble guide has 1 bar, the last length setting until you change it. 10 .454 11.53 .498 12.65 medium-cut attachment has two bars and the long-cut attachAlways be sure the trimming guide is 11 ment has three bars. These attachments are ideal for blendlocked solidly into the desired ing, tapering and defining beards, as well as for achieving a position before you start to trim. 3. To cut the outline of your beard, remove the trimming guide. “close trim” stubble look around the face. To use the attachments, go with the hair direction. To achieve closer looks, go Starting under your chin and working back toward your against the hair direction. jawbone and ears, cut the outer For the cleaning and care instructions of your trimmer, please perimeter of your beard underneath download the Care Instructions. the jawbone. Continue the line all the GOATEE TRIMMER Instructions way up to the ears and hairline. 4. Accentuate your beard line by using the trimmer in a downward motion. Start at the line you’ve created and, working from the chin back toward the ears, trim the area right under your beard line. 5. Define the upper part of your beard using the same technique. 6. For a neater finished look, replace attachment blade with the detail blade. Use this blade for fine, detail trimming anywhere it is needed, such as at the sideburns near the ears, goatees, etc. TRIMMING YOUR MUSTACHE 1. Comb your mustache. 2. To define the line of your mustache, begin with the trimmer blade. 9854, 9855, 9860 1/16” 1/8” 3/16” 9877 1/16” 1/8” 3/16” SERVICE AND REPAIR If you have problems with your WAHL product, send it prepaid with a note explaining the problem to: Wahl Clipper Corporation Attn: Repair Department 3001 Locust Street Sterling, IL 61081 Telephone (815) 625-6525 For products purchased outside the United States, contact your distributor.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project