Weed Eater | 115254226 | Instruction manual | Weed Eater 115254226 Instruction Manual

Weed Eater 115254226 Instruction Manual
ENGLISH
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Register your product online at:
Registre su producto en línea en:
Enregistrez votre produit en ligne à l’adresse :
www.weedeater.com
WE EL-15TNE
ESPAÑOL
245157
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Read instructions carefully before assembling.
Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual del operador y siga todas las advertencias e instrucciones de seguridad. Antes de ensamblar el producto lea cuidadosamente el instructivo. El no hacerlo puede resultar en lesiones graves.
AVERTISSEMENT:
Veuillez lire le manuel de l’utilisateur et bien respecter tous les
avertissements et toutes les instructions de sécurité. Bien lire les
instructions avant d’assembler l’outil. Tout défaut de le faire pourrait
entraîner des blessures graves.
WEED EATER
850 Matheson Blvd. West
Mississauga, Ontario L5V 0B4
115254226 Rev.3 05/07/10 JBW
FRANÇAIS
WEED EATER
7349 Statesville Road
Charlotte, NC 28269
SAFETY RULES
• Being fully covered also helps protect you
WARNING: When using electric gardening appliances, basic safety precautions
must always be followed to reduce the risk of
fire, electric shock, and serious injury. Read
and follow all instructions.
from debris and pieces of toxic plants
thrown by spinning line.
• Stay Alert. Do not operate unit when you
are tired, ill, upset or under influence of alcohol, drugs, or medication. Watch what
you are doing; use common sense.
• Avoid unintentional starting of the unit.
Never carry unit with your finger on the
switch. Be sure the switch is in the OFF
position and never touch the switch when
connecting extension cord.
SAFETY INFORMATION
ON THE UNIT
This power unit can be dangerous! Operator
is responsible for following the warnings and
instructions in this manual and on the unit.
Read entire instruction manual before using
unit! Be thoroughly familiar with the controls
and the proper use of the unit. Restrict the use
of this unit to persons who read, understand,
and follow unit and manual warnings and
instructions. Never allow children to operate
this unit. Close attention is necessary when
used near children.
ELECTRICAL SAFETY
WARNING: Avoid a dangerous environment. To reduce the risk of electrical
shock, do not use in rain, in damp or wet locations, or around swimming pools, hot tubs,
etc. Do not expose to snow, rain, or water to
avoid the possibility of electrical shock.
• Use a voltage supply as shown on unit.
• Avoid dangerous situations. Do not use in
the presence of flammable liquids or gases
to avoid creating a fire or explosion and/or
causing damage to unit.
• To reduce the risk of electrical shock, this
equipment has a polarized plug (one blade
is wider than the other) and will require the
use of a polarized extension cord. The appliance plug will fit into a polarized extension cord only one way. If the plug does not
fit fully into the extension cord, reverse the
plug. If the plug still does not fit, obtain a
correct polarized extension cord. A polarized extension cord will require the use of a
polarized wall outlet. This plug will fit into
the polarized wall outlet only one way. If
plug does not fit fully into the wall outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper wall
outlet. Do not change the equipment plug,
extension cord receptacle, or extension
cord plug in any way.
• To reduce risk of electrical shock, use extension cords specifically marked as suitable for outdoor appliances having electrical rating not less than the rating of unit.
Cord must be marked with suffix “W--A” (in
Canada “W”). Make sure your extension
cord is in good condition. Inspect extension
cord before use and replace if damaged.
Do not use a damaged cord. Cord insulation must be intact with no cracks or deterioration. Plug connectors must be undamaged. An undersized extension cord will
cause adrop in line voltage resulting in loss
of power and overheating. If in doubt, use
the next heavier gauge. The lower the
gauge number, the heavier the cord (see
SELECT ANEXTENSION CORD in the
OPERATION section).
• Do not use multiple cords.
DANGER: Never use blades or flailing devices. Unit is designed for line trimmer
use only. Use of any other accessories or attachments will increase the risk of injury.
WARNING: Trimmer line throws objects violently. You and others can be blinded/
injured. Wear safety glasses, boots, and leg
protection. Keep body parts clear of rotating
line.
Safety Glasses or similar eye protection
Hazard Zone
Boots
15 m
50 ft.
Keep children, bystanders, and animals 50
feet (15 meters) away. If approached stop unit
immediately.
If situations occur which are not covered in
this manual, use care and good judgement. If
you need assistance, call 1-800-554-6723.
OPERATOR SAFETY
• Dress properly. Always wear safety
glasses or similar eye protection when operating, or performing maintenance on your
unit. (Safety glasses are available.) Always
wear face or dust mask if operation is dusty.
Always wear heavy, long pants, long
sleeves, boots, and gloves. Do not go barefoot or wear sandals.
• Secure hair above shoulder length. Secure
or remove loose clothing and jewelry or
clothing with loosely hanging ties, straps,
tassels, etc. They can be caught in moving
parts.
2
• Do not abuse cord. Never carry the unit by
•
•
•
•
•
MAINTENANCE SAFETY
the extension cord or yank extension cord
to disconnect unit.
Use cord retainer to prevent disconnection
of extension cord from unit and possible
damage to the unit due to plug movement
(see ATTACH THE EXTENSION CORD
TO YOUR TRIMMER in the OPERATION
section).
Do not use the unit if the switch does not
turn the unit on and off properly. Repairs to
the switch must be made by your authorized service dealer.
Keep the extension cord clear of operator
and obstacles at all times. Do not expose
cords to heat, oil, water, or sharp edges.
To avoid the possibility of electric shock,
avoid body contact with any grounded conductor, such as metal fences or pipes.
Ground Fault Circuit Interrupter (GFCI)
protection should be provided on circuit or
outlet to be used. Receptacles are available having built-in GFCI protection and
may be used for this measure of safety.
WARNING: Disconnect unit from the
power supply before performing maintenance, or when changing trimmer line.
• Maintain unit according to recommended
procedures. Keep cutting line at proper
length. Follow instructions for changing
trimmer line.
• Have all service and maintenance not explained in this manual performed by an authorized service dealer to avoid creating a
hazard.
• Never douse or squirt the unit with water or
any other liquid. Clean unit and decals with
a damp sponge. Keep handles dry, clean,
and free from oil and grease.
• Keep the air vents clean and free of debris
to avoid overheating the motor. Clean after
each use.
TRANSPORTING AND STORAGE
• Stop the unit and disconnect the power
source when not in use.
• Carry the unit with motor stopped.
• Store the unit so the line limiter blade (on
UNIT SAFETY
• Inspect unit before use. Replace damaged
•
•
•
•
underside of shield) cannot cause injury.
• Store unit indoors in a high, dry place out of
parts. Make sure all handles, guards, and
fasteners are in place and securely fastened. Parts that are damaged must be repaired or replaced by an authorized service
dealer. These include head parts that are
cracked, or chipped, guards, and any other
part that is damaged.
Do not repair unit yourself.
Use only 0.065 inch (1.65 mm) diameter
recommended trimmer line (see USER
REPLACEABLE SERVICE PARTS in the
SERVICE AND ADJUSTMENTS section).
Never use wire, rope, string, etc.
Use specified trimmer spool. Make sure
spool is properly installed and all parts are
securely fastened.
Use only WEED EATER replacement parts
and accessories as recommended.
the reach of children. Store unit unplugged.
• Do not hang unit so that the trigger switch is
depressed.
DOUBLE INSULATION
CONSTRUCTION
This unit is double insulated to help protect
against electric shock. Double insulation
construction consists of two separate “layers”
of electrical insulation instead of grounding.
Tools built with this insulation system are not
intended to be grounded. No grounding
means is provided on this unit, nor should a
means of grounding be added to this unit. As a
result, the extension cord used with your unit
can be plugged into any standard 120 volt
electrical outlet.
Safety precautions must be observed when
operating any electrical tool. The double insulation system only provides added protection against injury resulting from an internal
electrical insulation failure.
CUTTING SAFETY
• Inspect area to be cut. Remove objects
•
•
•
•
•
(rocks, broken glass, nails, wire, string,
etc.) which can be thrown or become entangled in cutting head.
Do not overreach or stand on unstable support. Keep firm footing and balance.
Keep the cutting head below waist level. Do
not raise handles above your waist. Cutting
head can come dangerously close to your
body.
Keep away from cutting head and spinning
line.
Use unit properly. Use only for trimming,
edging, scalping, and mowing. Do not
force unit. It will do the job better and with
less risk of injury at the rate for which it was
designed.
Use only in daylight or in good artificial light.
WARNING: All electrical repairs to
this unit, including housing, switch, motor,
locking sleeve assembly, wires, etc., must be
diagnosed and repaired by qualified service
personnel. Replacement parts for a double insulated appliance must be recommended by
the manufacturer. A double insulated appliance is marked with the words “double insulation” or “double insulated”. The symbol
(square within a square)
may also be
marked on the appliance. Failure to have the
unit repaired by qualified service personnel
can cause the double insulation construction
to become ineffective and result in serious
injury.
SAVE THESE INSTRUCTIONS
3
ASSEMBLY
WARNING: If received assembled,
review all assembly steps to ensure your unit
is properly assembled and all fasteners are
secure.
WARNING: The upper and lower
tubes must be snapped together, remain permanently assembled together and the locking
sleeve assembly must be fully tightened before and during use to avoid serious injury to
the operator and/or damage to the unit. DO
NOT attempt to disassemble unit after initial
assembly.
TUBE ASSEMBLY
Upper Locking Sleeve Assembly
Wire protector
INSTALLATION OF ASSIST HANDLE
1. Place unit on a flat surface.
2. Remove knob and bolt from kit.
3. Push assist handle over the clamp on
the tube (see illustration).Handle can
be assembled as option 1 or 2 (Shown
Below) depending on the users
preference.
4. Install bolt in handle. Thread knob onto
bolt.
5. Adjust the handle up and down the tube
and pivot it to a comfortable position;
tighten knob securely.
Wires
Lower Locking Sleeve Assembly
1. Remove the wire protector from the
tubes and discard.
2. Align upper tube groove with triangle on
lower locking sleeve assembly. Push
tubes together until they snap into place.
Upper Tube
Groove
Assist handle
Alignment Triangle
3. Try to pull tubes back apart. If the tubes do
not come apart, they are properly snapped
into place. If the tubes come apart, repeat
step 1 and push until the tubes snap into
place.
4. Slide upper locking sleeve assembly over
lower locking sleeve assembly and tighten by turning clockwise.
Trigger
housing
Clamp
Tube
Option 1
Option 2
ATTACHING EDGE GUIDE AND
SHIELD
WARNING: The shield must be properly installed. The shield provides partial
protection from the risk of thrown objects to
the operator and others. Your unit is equipped
with a line limiter blade, which cuts excess
line to the proper length while running. The
line limiter blade (on underside of shield) is
sharp and can cut you.
NOTE: If shield is not properly installed, damage to unit (including motor failure) will result.
1. Insert edge guide into two holes in shield.
NOTE: Edge guide must be positioned on
shield prior to installation on motor housing
(see following illustration).
5. Ensure locking sleeve assembly and
alignment decals appear as illustrated below.
Alignment decals
WARNING: Failure to
completely enclose excess wires in upper tube during assembly of the unit may result in damage to the wires
and/or the unit or serious injury to the operator
including electrocution.
4
Edge Guide
CAUTION: Sharp line limiter blade
Shield
Holes
Bolt
2. Insert the shield onto the motor housing.
Ensure the cutting head remains free to
rotate and the line is not caught between
the shield and the motor housing (see
following illustration).
3. Twist the shield as illustrated until the hole
in the shield aligns with the hole in the
housings. Make sure the shield is
assembled to the unit as shown in the
following illustration and in the KNOW
YOUR UNIT section of this manual.
4. Install bolt into shield and motor housing as shown. Tighten securely.
Twist shield in this
direction to assemble
OPERATION
KNOW YOUR TRIMMER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
Trigger Switch
Assist Handle
Twist and Edge Button
Motor Housing
Edge Guide
Cord
Clamp
Retainer Recessed
Plug
Locking
Sleeve
Assembly
Air
Vents
Trimmer Head
with 0.065 inch
Trimmer Line
Debris Shield
Line Limiter Blade
RECESSED PLUG
TRIMMER HEAD
The RECESSED PLUG is where you attach
your extension cord to the unit.
The TRIMMER HEAD holds the cutting line
and rotates during operation.
The TRIGGER SWITCH is used to turn on the
unit. Squeeze the trigger switch to operate the
unit. Release to stop.
The TWIST AND EDGE BUTTON is used to
twist the lower portion of the unit into an edging position.
TWIST AND EDGE BUTTON
TRIGGER SWITCH
LINE LIMITER BLADE
EDGE GUIDE
The LINE LIMITER BLADE cuts the cutting
line to the proper cutting length.
The EDGE GUIDE protects the unit from contacting the ground during edging.
ASSIST HANDLE
The ASSIST HANDLE is used to help hold
and guide the unit.
5
OPERATING INSTRUCTIONS
ADJUSTING TRIMMER HEIGHT
The height of the trimmer can be adjusted
to achieve the most comfortable operating
position.
1. Push the Twist 'N Edge Button.
2. Adjust the trimmer to the desired height
by moving the motor housing up or
down the tube (four height positions
available).
3. Release the button. The tube will lock
in position.
Use only a voltage supply as specified on
your unit.
SELECT AN EXTENSION CORD
Extension Cord Gauge Chart
Length of Cord
Gauge
25 Ft. (7.5 m)
50 Ft. (15 m)
100 Ft. (30 m)
18 Gauge
16 Gauge
16 Gauge
AUTOMATIC LINE FEED SYSTEM
When the trimmer is initially started, a small
length of cutting line is fed out.
After approximately 5 seconds, the line will
be cut to the correct length by the line
limiter as the motor reaches full speed.
Make sure the motor is up to full speed
before trimming.
If the noise of the cutting line being cut
cannot be heard, more line will need to be
fed out.
To feed more line:
• Allow the motor to stop completely; then,
restart the motor and allow it to reach full
speed.
• Repeat until you hear the line hitting
against the line limiter (do not repeat this
procedure more than 6 times).
If problems are experienced with the
automatic line feed, refer to the TROUBLESHOOTING TABLE.
To manually feed the nylon line:
• If required, the cutting line can be fed out
manually.
• To operate, press and release manual
line feed button while gently pulling on
the line until the line reaches the line
limiter.
Extension cords are available for this unit.
ATTACH THE EXTENSION
CORD TO YOUR TRIMMER
Loop your extension cord through the handle
and around the hook as shown. Insure the
plug and cord are firmly and fully engaged.
Cord Retainer
Extension Cord
CORRECT OPERATING POSITION
Trimming
Edging
WARNING: Always wear eye protection. Never lean over the trimmer head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury.
When operating unit, stand as shown and
check for the following:
• Wear eye protection and heavy clothing.
• Hold trigger handle with right hand and assist handle with left hand.
• Keep unit below waist level.
• Cut only from your right to your left to ensure
debris is thrown away from you. Without
bending over, keep line near and parallel to
the ground (perpendicular when edging) and
not crowded into material being cut.
Manual Line
Feed Button
• If the line extends past the line limiter,
too much line has been fed out. If too
much line is fed out, remove the spool
cap and click spool counterclockwise
until the line is at the desired length.
6
SCALPING
The scalping technique removes unwanted
vegetation. Hold the bottom of the trimmer head
about 3 inches (8 cm) above the ground and at
an angle. Allow the tip of the line to strike the
ground around trees, posts, monuments, etc.
This technique increases line wear.
WARNING: Use only 0.065 inch
(1.65 mm) diameter round line. Other sizes
and shapes of line will not advance properly
and will result in improper cutting head function or can cause serious injury. Do not use
other materials such as wire, string, rope, etc.
Wire can break off during cutting and become
a dangerous missile that can cause serious
injury. See page 2 for warning concerning
other cutting devices.
TRIMMING
Hold the bottom of the trimmer head about 3
inches (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area.
Scalping
Trimming
MOWING
Your trimmer is ideal for mowing in places
conventional lawn mowers cannot reach. In
the mowing position, keep the line parallel to
the ground. Avoid pressing the head into the
ground as this can scalp the ground and damage the tool.
3 inches (8 cm)
above ground
Mowing
EDGING POSITION
While holding the trimmer in operating position, you can press this button and twist the
lower portion 180° counterclockwise for
edging.
Button
SWEEPING
The fanning action of the rotating line can be
used for a quick and easy clean up. Keep the
line parallel to and above the surfaces being
swept and move the tool from side to side.
Sweeping
EDGING
While edging allow the tip of the line to make
contact. Do not force the line. The edge guard
helps protect the unit and keeps the unit from
contacting the ground. Take extra caution
while edging as objects can be thrown from
the trimmer line.
Edging
7
MAINTENANCE
CHECK FOR DAMAGED OR
WORN PARTS
WARNING: Disconnect power
source before performing maintenance.
Contact an authorized service dealer for replacement of damaged or worn parts.
• Trigger Switch -- Ensure switch functions
properly by pressing and releasing the trigger switch. Make sure motor stops.
• Debris Shield -- Discontinue use of unit if
debris shield is damaged.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover items
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, the operator must maintain unit as
instructed in this manual. Various adjustments will need to be made periodically to
properly maintain your unit.
AFTER EACH USE
BEFORE EACH USE
INSPECT AND CLEAN UNIT AND DECALS
• After each use, inspect complete unit for
CHECK FOR LOOSE
FASTENERS AND PARTS
• Housing Screws
• Locking Sleeve Assembly
• Assist Handle
• Debris Shield
• Edge Guide
loose or damaged parts. Clean the unit using a damp cloth with a mild detergent.
• Wipe off unit with a clean dry cloth.
SERVICE AND ADJUSTMENTS
REPLACING THE LINE
1. Disconnect the unit from the power
source.
2. Press and hold in the two cap release
latches.
3. Pull cap away from the hub.
Cap
Spool
8. Wind the line evenly and tightly onto the
spool. Wind in the direction of the arrow
found on the spool.
9. Push the line into the notch, leaving 3 to 5
inches (7 -- 12 cm) unwound.
Cap
release
latch
Notches
Hub
Eyelet
10. Place spool into hub with cut out area of
spool in line with eyelet (see illustration).
4. Remove old spool.
5. Clean entire surface of hub and spool.
6. Replace with a pre--wound spool or cut a
length of 26 feet (8 meters) of 0.065″ (1.65
mm) diameter WEED EATER brand line.
Use of heavier lines could overload and
damage unit.
Cut out
area of spool
WARNING: Never use wire, rope,
string, etc., which can break off and become a
dangerous missile.
7. Insert end of line about 1/2 inch (1 cm)
into small hole on the inside of the spool.
Eyelet
11. Remove line from notch and feed line
through eyelet.
12. Reinstall the spool cap.
8
USER REPLACEABLE SERVICE PARTS
REPLACEMENT PART
PART NUMBER
Spool with 0.065 inch Trimmer Line
952711920
Assist Handle
574495601
Bolt Carriage, M6 X 1
Knob
Clamp
574495901
574473101
574495801
Shield Assembly
574495401
Edge Guide
574491601
Spool cap
574492201
Bolt
574471601
STORAGE
• Store unit and extension cord indoors in a
WARNING:
Perform the following
steps after each use.
• Stop the unit and disconnect the power
source when not in use.
• Carry the unit with motor stopped.
• Store the unit so the line limiter blade cannot cause injury.
high, dry place out of the reach of children.
Store unit unplugged.
• Store unit with all guards in place. Position
unit so that any sharp object cannot accidentally cause injury.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect from the power source before performing all of the recommended remedies below except remedies that require unit to
be operating.
TROUBLE
CAUSE
REMEDY
1. Allow tip of line to do the cutting.
Trimmer head
1. Crowding trimmer line
stops under a
against material being
load or does not
cut.
turn when switch 2. Electrical failure.
is pressed.
3. Thrown circuit breaker.
4. Debris stopping head.
Line does not
1. Line improperly routed
advance or
in head.
breaks while
2. Line improperly
cutting.
wound into spool.
3. Incorrect line size
4. Not enough line
outside of head.
5. Dirt buildup on unit.
Line welds onto 1. Line size is incorrect.
2. Incorrect spool.
spool.
3. Line is being crowded
against material being
cut.
1. Line improperly
Line releases
routed in head.
continuously.
2. Spool damaged.
2. Contact your authorized service dealer.
3. Check breaker box.
4. Remove debris.
1. Check line routing.
2. Rewind line tightly and evenly.
3. Use only 0.065 inch (1.65 mm) dia. line.
4. Remove spool cap and pull 4 inches
(10 cm) of line out of head.
5. Clean unit.
1. Use only 0.065 inch (1.65 mm) dia. line.
2. Replace with correct spool.
3. Cut with tip of line fully extended.
1. Check line routing.
2. Replace spool.
1. Check line routing.
Line usage is
excessive.
1. Line improperly routed
in head.
2. Line size is incorrect.
3. Crowding line against
material being cut.
4. Spool worn or damaged.
4. Replace spool.
Line pulls back
into head.
1. Too little line outside
of head.
2. Line size incorrect.
1. Remove spool cap and pull 4 inches
(10 cm) of line outside of head.
2. Use only 0.065 inch (1.65 mm) dia. line.
2. Replace spool.
3. Cut with tip of line fully extended.
9
LIMITED WARRANTY
WEED EATER, a division of Husqvarna
Consumer Outdoor Products N.A., Inc.,
warrants to the original consumer
purchaser that each new WEED EATER
brand electric or cordless product is free
from defects in material and workmanship
and agrees to repair or replace under this
warranty any defective WEED EATER
brand electric or cordless product within
two (2) years from the original date of
purchase.
If your WEED EATER brand electric or
cordless product should fail within the
limited warranty period, you may return it in
complete condition, prepaid, with proof of
purchase, to the dealer from whom it was
purchased for repair or replacement at the
option of WEED EATER.
This warranty is not transferable and does
not cover damage or liability caused by
improper handling, improper maintenance
or alteration, or the use of accessories
and/or attachments not specifically
recommended by WEED EATER for this
product. Additionally, this warranty does not
cover parts that will wear and require
replacement with reasonable use during the
warranty period. This warranty does not
cover predelivery set-up or normal
adjustments explained in the instruction
manual.
Should you have any unanswered
questions concerning this warranty, please
contact:
WEED EATER, a division of Husqvarna
Consumer Outdoor Products N.A., Inc.
7349 Statesville Road
Charlotte, NC 28269
1-800-554-6723
In Canada, contact:
WEED EATER
850 Matheson Blvd. West
Mississauga,Ontario L5V 0B4
Giving the model number, serial number and
date of purchase of your product and the name
and address of the authorized dealer from
whom it was purchased.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO
STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EXPRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY
TO YOU.
This is a limited warranty within the meaning of
that term as defined in the Magnuson--Moss Act
of 1975.
The policy of WEED EATER is to continuously improve its products. Therefore, WEED
EATER reserves the right to change, modify,
or discontinue models, designs, specifications, and accessories of all products at any
time without notice or obligation to any purchaser.
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising