Weed Eater VIP 157394 Owner's manual

Weed Eater VIP 157394 Owner's manual
 se,
me
cu
call 1-800-849-1297
tributor:
800-829-5886
5
zed di
contact our author
се,
For Parts and Serv
$.
И
ical Assistance: ca
E
For Techn
FAVE TT FOLLOWIN
Read, understand, and follow all instructions in the manual
and on the machine before startin ng.
Only allow responsible adults, who are familiar with the
instruct ons, to operate the machine.
e (lear the area of objects such as rocks, toys, wir
which could be picked up and thrown by the blade.
e Besurethe areais clear of other people before mowing. Stop
machine if anyone enters the area,
« Never carry passengers.
¢ Do not mow in reverse unless absolulely necessary. Always
look down and behind before and while > backing.
е Be aware of the mower discharge direction and do not point
it at anyone. Do not.operate the mower without either the
entire grass catcher or the guard in place.
«Slow down before tuming.
« Never leave a running machine unatiended. Always turn off
blades, set parking brake, stop engine, and remove keys
before dismounting.
е Turn off blades when not mowing.
o Stop engine before removing grass calcher or unclogging
chute.
= Mow only in daylight or good artificial light.
е Do not operate the machine while under the influence of
alcohol or drugs.
* Watch for traffic when operating near or crossing roadways.
e Use extra care when loading or unloading the machine into
a trailer or truck.
; Bm
E, E.
tipover accidents, which can resultin severe injury or death.
Ali slopes require extra caution, If you cannot back up the
slope or if you feel uneasy on it, do not mow it.
е Mow up and down slopes, not across.
* Remove obstacles such as rocks, tree limbs, etc.
« Waich for holes, ruts, or bumps. Uneven terrain could
overturn the machine. Tall grass can hide obstacles.
» Use slow speed. Choose alow gear so that you will not have
to stop or shift while on the slope.
» Follow the manufacturer's recommendations for wheel
weights or counterweights to improve stability.
« Use extra care with grass catchers or other attachments.
These can change the stability of the machine.
о Keep all movement on the slopes slow and gradual. Do not
make sudden changes in speed or direction.
* Avoid starting or stopping on a si ope. if tires lose traction,
disengage the blades and proceed slowly siraight down the
slope.
ы ро по! tumon slopes unless necessary, andthen, urn slowly
and gradually downhill, if possible.
+ Do not mow near drop-offs, ditches, or embankments. The
mower could suddenly tum over if a wheel is over the edge
of a cliff or ditch, or if an edge caves in.
e bo not mow on wet grass. Reduced fraction could cause
sliding.
* Do not try to stabilize the machine by putting your foot onthe
ground.
[Do not use grass calcher on steep slopes.
Slopes are a major factor related to loss-of-control and
те MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET A D THROWING OBJECTS.
IG SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
И.
Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted fo the
machine and the mowing activity, Never assume that
children will remain where you last saw them.
* Keep children out of the mowing area and under the watchful
care of another responsible adult.
Be alert and turn machine off if children enter the area.
« Before and when backing, look behind and down for small
children.
« Never carry children. They may fall off and be seriously
injured or interfere with safe machine operation.
e Never allow children to operate the machine
« Use extra care when approaching blind comers, shrubs,
trees, or other objects that may obscure vision.
№ || ни
sa
Use extrac care in handling gasoline and other fuels. They are
flammable and vapors are explosive.
- Use only an approved container.
- Never remove gas cap or add fuel with the engine
running. Allow engine to cool before refueling. Do not
smoke.
- Never refuel the machine indoors.
- Never store the machine or fuel container inside where
there is an open flame, such as a water heater.
« Never run a machine inside a closed area.
s Keep nuts and bolis, especially blade attachment bolts, tight
and keep equipment in good condition.
es Never tamper woth safety devices.
operation regularly.
» Keep machine free of grass, leaves, or other debris build-up.
Clean oil or fuel spillage. Allow machine to cool before
storing.
« Stop and inspect the equipment if you strike an object.
Repair, if necessary, before restarting.
e Never make adjustments or repairs with the engine running.
* Grass catcher components are subject to wear, damage, and
deterioration, which could expose moving parts or allow
objects to be thrown. Freguently check components and
replace with manufacturer's recommended paris, when nec-
essary.
e Mower blades are sharp and can cut. Wrap the blade(s) or
wear gioves, and use extra caution when servicing them.
* Check brake operation frequently. Adjust and service as
required.
Check their proper
disconnect spark plug
reitcannot contact
o prevent accidental
on your purchase of a New Trac-
tor. thas beendesigned, engineered and manufactured io
give you the best possible dependability and performance.
|
S Should you experience any problem you cannot easily
remedy, please conte 3 ict your nearest authorized service
center/Department. We have competent, w ell-trained tech-
nicians and the proper 10015 10 serv air this tractor,
ice or repe
© id retain this manual. The instruct ions will
le > you to assembl e andn nai intain your tractor pro
enab репу.
Always observe mu “SAFETY RULES”
FOR FUTURE R
« Head and observe the safety rules
e. Followaregularschedule |
using your tractor.
e Followthe instructions under “Customer Responsibili-
ties” and “Storage” sections of this owners manual.
e inmaintalning, caring for and
BLADE BOLT TORQUE:
12.5
1.25 GALLO IS
UNLEADED REGULAR
SAE 30 (above 32°F)
SAE BW-30 (below 32°F)
CHAN (PION RJI19LM
STD 361458
INTAKE: .005" - 007"
EXHAUST: 009" - 011°
ist
2nd
3rd
4th
5th
REVERSE:
FRONT: 14 PSI
3 AMPS B ATTERY
5 AMPS HEADLIGHTS
AMP/HA: 25
MIN. CCA: 190
CASE SIZE: U1R
HORSEPOWER:
GASOLINE CAPACITY
OL TYPE (API-SF/SG):
OIL CAPACITY:
(GAP: 030")
VALVE CLEARANCE:
GROUND SPEED (MPH):
TIRE PRESSURE:
CHARGING SYSTEM:
BATTERY:
ING: This tractor is equipped with an internal
combustion engine and should not be used on or near any
unimproved forest-covered, brush-covered or grass-cov-
ered land unless the engine's exhaust system is equipped
with a spark arrester meeting applicable local or state laws
(it any). If a spark arrester is used, it should be maintained
in effective working order by the operator.
in the state of Cali fornia the above | is required by law
(Section 4442 of the California Public Resources Code).
Other states may have similar laws. Federal laws apply on
federal lands. A spark arrester for the muffler is available
through your nearest Sears Authorized Service Center/
Department (See REPAIR PARTS section of this manual).
(TETE ET EE EEE ETES EEE ET LISS perso ae RY SR nad RR RE a nes de
e
a ® A EEE 5
REE
SE Ш Ш i E es de de LE TE
Adjustments:
Brake econ. В ооншаечьниароснойенононанивииаизойно 22
Vower | To-B | enano ©
Side-To-Si de. pe lsaesnen see na sse sen cuens 20
Thnrottie Control Cable... 24
Air Filter, Engine
Air Screen, Engine
Assembly... crcsresescrsauretscerennanencue
Battery:
Charging picurinenenonoreravecaces EEE EEE . 8
Cleaning | |
Starting with Weak Battery. 23
Storage ......... ..—.—.e—mensne 26
Terminals ..............———..... enveneos ne 17
Belt: |
Motion Drive
Removal/Replacement............ 22
Mower Blade(s)
Removal/Replacement............ 22
Blade:
Sharpening.............—.... 16
Replacement ................eeecemororenos 16
Brake Adjustment ................ SA use 22
Carburetor Adjustment ..........c............. 25
Controls, Tractof ........... e... ee... 11
Customer Responsibilities.............. 15-19
Engine:
Air FIEr..…ro…rcsenrsserencrncennenses 18
Air Screen, Engine ............... 18
Cooling Fins, Engine .......... ne... 18
Engine Oil ......... neovaneon enano TZ
A Ei ene 19
Spark Plug(s) ere 19
Tractor:
511 17
Blade …….…unrcnsenseensescerrecaecencense 16
Lubrication Chart………………………… 15
Maintenance Schedule ............ 15
Tie Care ovine, 8,14,23
Transaxie seras 1
Cutting Height, M
BREEGESES ESSE Ee ER Bb
8 GE HU A dE 05 A 0p NR VE GEES E EN EA El E ANS BR OF ob do BSW OF OR de E SM
fa
E ES AS dE E E ES E SEC Y E A E EEE EA EA
ctrical:
interlocks and Relays .................. 24
Schematic me... enero 29
Wiring Diagram eee eine 30
Engine:
Air Filter... ere peucrcures canons 18
Air Screen... 18
Cooling Fins, Engine areca 18
Ч i Level вест нп новое овен йе век 13,17
LW il fype............ sdddrapdep TONLE LEG hud dh Ew HR 1 {
Р "E
reparation HERRCHEN RUHR 13
В 7 A
Hepair Parts 48-52
HEHE RY ERE RYAN ESE EDRF FEE EEE
SHANG сонное! 1 3
su
a A
Filter:
= A
+ Fi 8
Air ter crus eu c scans ane ne nca nana san 1
Ë це! qu в ев FORE ELE RD TEE ETE пин FD 19
Fuel: ;
LS +
e - ce cascerseccerersrersne can mere vee 13
Siorage .......... eee a, ... 26
| Use ZEECERLEN RY RTEEY BRERA DEAF EARRI ODEN REESE ERS ENED EN dnd 2 ;
La
Hood Hemoval/lnstallation .................. 24
Leveling Mower Deck Gaccarerenaaa nice c carre 21
Lubrication:
Chart. …srcsrensensensandeucanacenenvenan ne 15
vaintenance Schedu
Adiusiment, Front-to-Back 21
Adjustment, Side- to-Side on. 21
Blade Sharpening .............—.... 16
Blade Repl acement.............—.. 16
Cutting Height oo. 12
Installation encens 20
TEE EE LE Ur EEE EM E E BENE LEE ERG SE REIN SERGE eRe RE RE REY AN Sr rR EER
Un dé de WOM WOR OB MN EWE WWE WW RN BE HHREHFEFERS SS San 1
FHEFRBE PFE ERLE ERNE REAR RW ERE EE
Emma dbs AS MÁ SER US ES ES 15 65 EN NE Ge CNE GR RE RES YE NE 05 TE E 18 EL EE UE Ue ES E E
i RO ER OW RR
Engl "e Boa EN NE DARE RS EY RR ER RAN bk ERE FERS ERR SRE EEN EE 17
Storage HEE ET REDE FEST TRAC EERE STEERER EG ES EEE 26
Operation
Parking Brake
Parts Bag ......... poaneeronereoraneenaconooroneceanano.
Parts, ReplacemenV/Hepair ............ 30-47
Product Specifications. .............. we... 3
RepairPars GOTT
Safety Rules |
SOA L.cuccesecrerscencercenesrese rere ceo neeens 8
Service and Adjustments ............ ... 20-25
Carburetor ................. eer ereenanaa 25
FUSE ....nerininizcercorenenaenoenerea cnn eee 24
Hood Removal/Installation ........... 24
Motion Drive Belt
Removal/Replacement............ 22
Mower Belt(s)
Removal/Replacement............ 22
Mower Adjustment
Front-lo-Back .......... аваненнннненнее 1
Side-to-Side eme 21
Mower Removal ere ... 20
Tire Саге ....мыиинеаенеееннеснеееноые 8
Slope Guide Sheet ................. ees 51
Spark PIUS) ae 0... 19
Specifications es .3
Starting the Engine heer 13-14
Steering W
Stopping the Tractor... 12
5101 mecenas 26
Throttle Control Cable Adjustment ...... 25
Li CA 0e 8,16,23
Trouble Shooting Chart AA 27-28
Wiri
The Manufacturer warrants to the original consumer purchaser thal this product as manufactured is free from defects in
materials and workmanship. For a period cf two (2) years from date of purchase by oy the original consumer purchaser, we will
repair or replace, at our option, without charge for paris or labor incurred in replacing parts, any part which we find fo be
detective due to materials or workmanship. This Warranty is subject to the following limitations and exclusions.
1. This warranty does not apply to the engine, other than AYP manufactured transaxe/firansmission components, battery
(except as noted below) or components parts thereof. Please refer to the applicable manufacturer's warranty on these
items.
2. Transportation changes for the movement of any power equipment u unit or attachment are the resp ponsioity of the
purchaser.
be mai intained in y accordance with the instructions > fumiéhed
4 Te Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date of
original purchase.
5. This Warranty applies oniy to products which have been properly assembled, adjusted, operated, and maintained in
accordance with the instructions furnished. This Warranty does not apply to any product which has been subjected to
alteration, misuse, abuse, | Improper assembly or installation, delivery damage, or to normal wear of the product.
6. Exclusions: Excluded from this Warranty are belts, blades, blade adapters, normal wear, normal adjustments, standard
hardware and normal maintenance.
7. Inthe event you have a claim under this \ Narranty, you must retum the product to an authorized service dealer
Should you have any unanswered questions concerning this Warranty, please contact:
American Yard Products in Canada contact:
Service Depariment | American Yard Products
Р.О. Вох 1687 1580 Trinity Drive, Units 5-8
ESTA ILS
giving the model number, serial number and date of purchase of your product and the name and address of the authorized
dealer from whom it was purchased.
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRAN- |
IE PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES. Some areas
TIES ARE LIMITED TO THE SAME TIM
do not allow the limitation of consequential damages or limitations of how long an implied Warranty may last, so the above
limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have other rights
which vary from locale to locale.
EE
oe
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.
(1) Lockwasher 3/8
(1) Locknut 5/16-18
(1) Shoulder
Bolt 5/16-18
12-13 В
(1) Lock Washer 1/2
6 x 12 Gauge
Steen ing
Boot
ma RO PASO db WERO куры om .
ные ны se GOR вн bor кн with dh oh
Parts Bag
ors]
| Steering V
Vheel
Adapter
Extension
Shaft
Slope Sheet
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use
the correct tools as necessary to insure proper tightness.
A socket wrench set will make assembly easier. Standard
wrench sizes are listed.
(1) 9/16" wrench
(2) 7/16" wrenches
(2) 1/2" wrenches
(1) 3/4" wrench
Tire pressure gauge
Utility knife
When right and left hand are mentioned in this manual, it
means when you are in the operating position (seated
behind the steering wheel).
» Remove all accessible loose parts and parts cartons
from carton (See page 6).
« Cut along lines on carton, from top to bottom, all four
corners of carton and lay panels flat.
e Check for any additional loose parts or cartons and
remove.
ASSEMBLE EXTENSION SHAFT AND BOOT
e. Slide extension shaft onto lower steering shaft. Align
mounting holes in extension and lower shafts and
install 5/16 hex bolt and locknut. Tighten securely.
MPORTANT: TIGHTEN BOLT AND NUT SECURELY TO
18- 22 FT. LBS TORQUE.
° Place tabs of steering boot over tab slots in dash and
push down to secure,
INSTALL STEERING WHEEL
» Position front wheels of the tractor so they are pointing
straight forward.
* Slide steering wheel adapter onto steering shaft exten-
sion.
* Position steering wheel and sleeve assembly So Cross
bars are horizontal (left to right) and slide onto adapter.
* Assemble large flat washer, 3/8 lock washer, 3/8 hex
bolt and tighten securely.
» Snap steering wheel insert into center of steering
wheel.
* Remove protective plastic from tractor hood and grill.
MPORTANT: CHECK FOR AND REMOVE ANY STAPLES
IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR
IS TO ROLL OFF SKID.
— 3/8 HEX BOLT
_ 3/8 LOCK
WASHER
W A ss м Е A
STEERING
A VHEEL _ STEERING
Pr BOOT
a, TABS
_ D | extension sa
ADAPTER 1 |
a 5/16 HEX BOLT
5/16 LOCKNUT 7 hc
STEERING”
SHAFT
)
* Press liftlever plunger and raise attachment lift lever to
its highest position.
« Release parking brake by depressing clutch/brake
pedal.
* Place gearshift lever in neutral (N) position.
» Roll tractor backwards off skid.
Remove banding holding discharge guard up against
tractor.
ervi Г Jonth and year
(label located between terminals)
in ir num of one h our at € 6-1 0 am ps.
Г patter, ry y cable to positive (+) terminal
asher and hex nut as
io ет securely,
Connect BLACK grounding cable to negative (-) termi-
nal with remaining hex bolt, flat washer, lock washer
and hex nut. Tighten securely.
¢ Close battery box door.
Open battery box door for:
+ Inspection for secure connections (fo tighten hard-
ware).
e Inspection for corrosion.
Testing battery.
® Jump! ng (if requi ired).
Periodic charging .
(RED) CABLE CAPS
inf j adjustn ment bolt.
j on seat pan.
Place seat on pan and assembl e shoulder bolt.
s Assemble adjustment bolt, lock washer and flat washer
loosely. Do not tighten.
e Tighten shoulder bolt securely.
ss | nwer seat into operating position and sit on seat,
Adjust seal before ti
9 Remove cardboard packin: ng
Raat! any? ati A
« Slide seat until a comfortable position is reached which
allows youto press clutch/brake pedal ali the way down
(See Fig. 8).
Get off seat without moving its adjusted position.
е Raise seat and tighten adjustment boli securely.
For best cutting results, moi
level ed. See e TOL LE
mower blade drive belts i in the Servic m
Verify that the belts are routed
ami
section of this manual.
correctly.
After you learn how to operate your tractor, check to see
th at the brake is properly ad justed. See "TO ADJL
BRAKE" in the Service and Adjustments section of this
manual.
NGC
п со mpleted.
A I assen ha instructions have bee
No remaining loose parts in carton.
Battery is property prepared and charg
1 hour at 6 amps).
Seat is adjusted comfortably and tightened securely.
All tires are properly inflated. (For shipping purposes,
the tires were overinflated at the factory).
Be sure mower deck is properly leveled side-to-side/
front-to-rear for best cutting results. (Tires must be
properly inflated for leveling). |
Check mower and drive belts. Be sure they are routed
properly around pulleys and inside all belt keepers.
Check wiring. See that all connections are still secure
and wires are propery clamped.
ed. (Minimu
Eo
Eng ne oil is at proper level.
Fuel tank is filled with fresh, clean, regular unleaded
gasoline.
Become familiar with all controls
: - their location and
Operate them before you start the engine.
in safe operating condition.
function.
Be sure brake > system is
Sema:
These symbols may appear on your tractor or in literature
CLUTCH
strations with
Compare the illu |
or future reference.
ей
this manual fo
vs aw
ctr Wie
ty,
ME ees ame A
5 JER DECK
HEIGHT ADJUST-
MENT POSITIONS
Our tractors conform to the safety standards of the American National Standards institute.
Used to engage the
mower blades, or other attachments mounted to your
tractor.
- Tums the headlights on and off.
Used for starting and
controling engine speed.
CLL Used for declutching and brak-
ng the 1 tractor ‘and starting the engine.
: Locks clutch/brake pedal into the
brake position
se
Selects the speed and direction of
tractor.
Used to raise, lower and
adjust the mower deck or other attachn 1ents mounted to
your tractor.
| Used to release attachment lift
ever when chang ng its position.
|
iC Used for starting and stopping the
Your tractor is equipped wi jth an operator presence sensing
switch. When engine is running, any attempt by the
operator to leave the seat without first setti ing the parking
brake will shut off the engine.
« Depress clutch/brake pedal into full “BRAKE
and hold.
® Placer parki n g brake lever in “El
” position
posit ion and
remain nin “BRAKE” position. Make sure parkin ng brake
will hold tractor secure.
Move attachment clutch lever to “DISENGAG
sition.
GROUND DRIVE -
) position
: Failure to nove throttle control to slow
on and allowi по ‹
ignition key t to “OFF” position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use.
. : Under certain conditions when tractor is standing
idle with the engine run: ng, hote m
| cause “orowning” | fa
batte ry cha q ing rate.
e Full throttle offers the best baggi
mance.
erfor-
The chi rection and speed of n ovement | is controlled by the
gearshift lever.
ith clutchv/brake pedal depressed and
° Start tractor wi г
gearshift lever in neutral (N) position.
Move gearshift lever to desired position.
Slowly release clutch/brake pedal to start movement.
ANT: BRING TRACTOR TO A COMPLETE STOP
BEFORE SHIFTING OR CHANGING GEARS. FAILURE
TO DO SO WILL SHORTEN THE USEFUL LIFE OF YOUR
TRANSAXLE.
rox
Hpac
ATE ppm
Y “DISEN IGAGED”
7 / POSITION
\ A ENGAGED” POSITION
BRAKES (AN
Mg Ч I В Vu Lu a Y IS EN G AG ED”
CLUTCH/BRA
PEDAL
The position of the attachment lift lever determines the
cutting height.
Grasp lilt lever.
® = Ге
position.
The cutting g height range is approximately 1-1/210 4°, The
heights are measured from the ground to the blade ti tip with
the engine not running. These heights are approximate
гу depending upon soil conditions, height of
nd types of grass being mowed.
э The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate grow vin
* For best cutting performance, grass over 6 inches in
height should be mowed twice. Make the first cut
relatively high; the second to desired height.
Your tractor isequ ipped with an ope rator| presence sensin
switch. À Алу attemp t by the ope rator to leave the se at wi
the eng ing and the attachment clutch engaged will
TE
gine running
shut off the engine.
Select desired heig
Start mower blades by eng
control.
s TOSTOPR BLADES
clutch control.
"DISENGAGED
POSITION
®
Choose the slowest speed before starting up or down
hills. ' |
Avold stopping or changing speed on hills.
6 i { slowing is necessary, move throttle control lever to
slower posit tion.
« If stopping is absolutely necessary, push clutch/brake
pedal quickly to brake position and engage parking
brake.
* Move gearshift lever to 1st gear.
aliowed room for tractor to roll slightly as you restart
novement.
° To restartmovemen
clutch/brake pedal.
s Make all turns slowly.
de sure you have
* Raise attachment lift to highest position with attach-
ment lift control.
When pushing or towing yo ur tractor, be sure gearshift
lover i is in neutral (N 1) position.
Do not push or tow tractor at more than five (5) M
=: To protect hood from damage when tran porn ng
your tractoron atruckoratrailer, be sure hood is closed and
securedto tractor. Use an appropriate means oftying hood
to tractor (rope, cord, etc.)
The engine in your tractor has been shi pped: from the
factory, already filled with summer weight oil.
® Check engi e oll with tractor on level ground.
« Remove oil fill cap/dipstick and wipe clean, reinsert the
dipstick and screw cap tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
° For cold weather operati ion you should nae oil for
easier mer Re С J (See ol Vi SCOSI ITY C CHART” in the
ties section gine ol manual,
° Fill fuel tank. Use fresh, clean, regular unleaded
gasoline with a minimum of 87 octane. (Use of leaded
gasoline will | norease carbon and lead oxide deposits
and reduce valve life). Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days | to assure fuel freshness.
i NT: WHEN OPERATING IN TEMPERATURES
B E LO 32 F(0° C), USE FRESH, C LEAN WINTER GRADE
GASOLINE TO HELP INSURE G OG CD COLD WEATHER
STARTING.
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or methanol) can
attract moisture which leads to separation and formation of
acids during storage. Acidic gas can damage the fuel
system of an engine while in storage. To avoid engine
problems, the fuel system should pe emptied before stor-
age of 30 days or longer. Drain the gas tank, start the
engine and let it run unti | the fuel li nes and carburetor are
empty. Use fresh fuel next season. € ee ‹ storage instruc-
tions for additional information. Never use engine or
carburetor cleaner products in the fuel tank or permanent
damage may occur.
n starting the engine for the first time or if the engine
has run out of fuel, it will take extra cranking time to move
fuel from the tank to the engine.
« Depress clutch/brake pedal and set parking brake.
s Place gear shift lever in neutral (N) position.
e Move attachment clutch to “DISENGAGED” position
Move throttle control to choke ([x) position.
Note: Before starting, read the warm and cold starting
procedures below.
= Insertkeyintoignitionand turnkey clockwise to “START”
position and release key as soon as engine starts. Do
not run starter continuously for more than fifteen sec-
onds per minute. If the engine does not start after
several attempts, move throttle control to fast (49)
position, wait a few minutes and try again. If engine still
does not start, move the throttle control back to the
choke (|) position and retry.
WARM WEATHER STARTING (50° F and above)
* When engine starts, move the throttle control to the fast
(<») position.
- The attachments and ground drive can now be used, if
the engine does not accept the load, restart the engine
and allow it to warm up for one minute usi ing the choke
as described above.
COLD WEATHER STARTING (50° F and below)
* When engine starts, allow engine to run with the throttle
control in the choke (|x|) position until the engine runs
roughly, then move throttie control to fast (4) position.
This may require an engine warm-up period from
several seconds to several minutes, depending on the
temperature.
¢ The attachments can also be used during the engine
warm-up period.
NOTE: If at a high altitude (above 3000 feet) or in cold
temperatures (below 32 F) the carburetor fuel mixture may
need to be adjusted for best engine performance. See “TO
ADJUST CARBURETOR” in the Service and Adjustments
section of this manual.
Yi я ©
Tire chains cannot be used when the mower housing
is attached to tractor.
Mower should be properly leveled for best mowing
performance. See “TO LEVEL MOWER HOUSING” in
the Service and Adjustments section of this manual.
Use the runner on the right hand side of mower as a
guide. The blade cuts approximately an inch outside
the runner (See Fig. 7).
The left hand side of mower should be used for trim-
ming.
Drive so that clippings are discharged onto the area
that has been cut. Have the cut area to the right of the
machine. This will result in a more even distribution of
clippings and more uniform cutting.
When mowing large areas, start by turning to the right
so that clippings will discharge away from shrubs,
fences, driveways, etc. After one or two rounds, mow
in the opposite direction making left hand turns until
finished (See Fig. 8).
If grass is extremely tall, it should be mowed twice to
reduce load and possible fire hazard from dried clip-
pings. Make first cut relatively high; the second to the
desired height.
Do not mow grass when it is wet. Wet grass will plug
mower and leave undesirable clumps. Allow grass to
dry before mowing. |
Always operate engine at full throttle when mowing to
assure better mowing performance and proper dis-
charge of material. Regulate ground speed by select-
ing a low enough gear to give the mower cutting
performance as well as the quality of cut desired.
When operating attachments, select a ground speed
that will suit the terrain and give best performance of
the attachment being used.
ñ
me
AS YOU COMPLETE
REGULAR SERVICE
Check Brake Operation
Check Tire Pressure
Check for Loose Fasteners
Sharpen/Replace Mower Blades
Lubrication Chart
Check Battery Level/Hecharge
Clean Battery and Terminals
Check Transaxle Cooling
Adjust Blade Belt{s) Tension
Adjust Motion Drive Bell(s} Tension
Check Engine Oil Level
Change Engine Oil
Clean Air Filter
Clean Air Screen
Inspect Muffler/Spark Arrester
Renlace Ou Filter (If equipped)
Clean Engine Cooling Fins
Replace Spark Plug
Fieplace Air Filter Paper Cartridge
Replace Fuel Filter
1 - Change more often when operating under a heavy load or in high ambient temperatures.
2 - Service more often when operating in dirty or dusty conditions.
3 - If equipped with oil filter, change oi every 50 hours.
4 - Replace blades more often when mowing in sandy soil.
The warranty on this tractor does not cover items that have
been subjected to operator abuse or negligence. To
receive full value from the warranty, operator must maintain
tractor as instructed in this manual.
Some adjustments will need to be made periodically to
properly maintain your tractor.
8 All adjustments in the Service and Adjustments section of
this manual should be checked at least once each season.
« Once a year you should replace the spark plug, clean
or replace air filter, and check blades and belts for
wear. A new spark plug and clean air filter assure
proper air-fuel mixture and help your engine run better
and last longer.
* Check engine oil level.
e Check brake operation.
* Check tire pressure.
e Check for loose fasteners.
- equipped with adjustable system.
6- Not required if equipped with maintenance-free battery.
7 - Tighten front axie pivot boit to 35 ft-lbs. maximum.
Do not overtighten.
r—- SPINDLE ZERK (2)
MPORTANT: DO NOT OIL OR GHEASE THE PIVOT POINTS
WHICH HAVE E SPECIAL NYLON BEARINGS. VISCOUS LUBRI-
CANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORTEN
THE LIFE OF THE SELF-LUBRICATING BEARINGS. IF YOU
FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POW-
DERED GRAPHITE TYPE LUBRICANT SPARINGLY.
ad justed
ar, then brake n must | |
-" in the Service and Adjust-
Maintain proper air ressure in all tires (See ” PROD
UCT £ SPECIFICATIONS” on page 3 of this r nanual).
Keep tires free of gasoline, oil, or insect control chemi-
cals which can harm rubber.
« Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage
For best results mower blades must be kept sharp. Re-
place bent or damaged blades.
Raise mower to highest position to allow access to
blades. |
Remove hex bolt, lock washer and flat washer secur ng
blade.
e Install new or resharpened blade with trailing edge up
towards deck as shown.
e HKeassemble hex boit, lock washer and flat washer in
exact order as shown.
eT] ighter bolt securely (30-35 Ft. Lbs. torque).
" iT. BLADE BOLTIS GRADE 8 HEAT TREATED.
We do not recommend sharpening blade - but if vou
do, be sure the blade is balanced.
Care should be taken to keep the blade balanced. An
unbalanced blade will cause excessive vibration and even-
tual damage to mower and engine,
® The blade can be sharpened with a file or on a grinding
wheel. Do not attempt to sharpen while on the mower.
To check blade balance, you will need a 5/8" diameter
steel bolt, pin, or a cone balancer. (When using a cone
balancer, follow the instructions supplied with bal-
ancer).
* Slide blade onto an unthreaded portion of the steel bolt
or pin and hold the bolt or pin parallel with the ground.
If blade is balanced, it should remain in a horizontal
position. If either end of the blade moves downward,
sharpen the heavy end until the blade is balanced.
NOTE: Do not use a nail for balancing blade. The lobes of
the center hole may appear to be centered, but are not.
Your tractor has a battery ch arging system which is suffi-
clent for normal use, However , periodic charg ing j of the
ry with an automotive © charge ger will ext
mE
® Keep s mail vent holes c open.
Recharge at 6-10 amperes for 1 hour.
minals can cause
> leak’ power.
= Open paren à / box door.
Disconnect B ery cable first then RED
te 5 cable and remove battery from tractor,
355
—
n=
ii
an
‚ ee
23
=
©
ar
a
ма
CL
SF
as,
=r
‹Э
м =
=
ED
WT
cd
fd
A
=
me
po.
=
wo
Ш
>
«5х
с
CA
=
ск I bright.
« Coat terminals with grease or petroleum j
Assembly section of this manual),
Check V-belts for deterioration and wear after 100 hours of
operation and replace if necessan
adjustable.
. The belts are not
Heplace belts if they begin n to slip from wear.
Keep transaxle free from build-up of dirt and chaff which
can restrict cooling.
Only use high quality detergent oil rated with API service
classification SF or SG. |
electthe oil's SAE viscos ty grade
to re ted {
SAE VISCOSITY GRADES
-20° go 30° 39° 40° 60° age 100°
Co. -20° 1 gs 19°
TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHARGE
: Althougk mult i-viscosity oils (5W Зо: 10W30 etc.)
р ting cf weather, these mult viscosity o oils
will result in inc eased oil consumption when used above
32°F. Check your engine oil level more frequently to avoid
р ossibl e gin ine damage from running low on oil.
9 ; e first two hours of operation and
every 5 hours thereafter or at least once a year if the
tractor Is not used for 25 hours in one year.
. Check the crankcase oll level before starting the engin
and after each eight (8) hours of operation. Tighten oil fi |
cap/dipstick securely il time no check the oil level.
e (Jil
will drain more freely when warm.
e Catch oil in a suitable container.
. Remove oil fi capa pst ick. Be careful not to allow dirt
® After oil has dra ned completely, repli ace oil drain plug
and tighten securely.
* Hefill engine with oil through oil fill dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
“PRODUCT SPECIFICATIO NS” on page 3 of this
manual.
e Use gauge on oil fill cap/dipsti ick for checking level. Be
sure dipstick cap is tightened securely for accurate
reading. Keep oil at “FULL” line on dipstick.
Ld
Remove any dust, dirt or oil from engine cooli ing fins to
prevent engi ne damage from overheat ing.
ler nove ао rews from blower housing and
lift housing
jne où Wrap | it in clean, absorbent ® Use COM pressed a air or stiff bristle brush to ihoroughy
o remove excess oil. clean engine cooling fins.
a To reassemble, reverse above procedure.
Remove cartri ridge nut.
¢ Carefully remove cartridge to prevent debris from en-
tering carburetor. Clean base carefully to prevent
debris from entering carb
е Clean cartridge by tapping gently on flat surface. If very
dirty or damaged, replace cartridge.
* Reinstall cartridge, nut, precleaner, cover and secure
with knob(s).
MPORTANT: PETROLEUM SOLVENTS, SUCH AS
KEROSENE, ARE NOT TO BE USED TO CLEAN THE
CARTRIDGE. THEY MAY CAUSE DETERIORATION OF
THE CARTRIDGE. DO NOT OIL CARTRIDGE. DO NOT
USE PRESSURIZED AIR TO CLEAN OR DRY
CARTRIDGE.
ate a fire hazard and
|
ati Е N h ic h EVE r
Ne
Ci at the
The fuel filter should be replaced once each season. If fuel
filter bacomes clogged, obstructing fuel flow to carburetor,
replacement is required.
* With engine cool, remove filter and plug fuel line
sections,
* Place new fuel filter in position in fuel line with arrow
pointing towards carburetor.
е Be sure there are no fuel line
properly positioned.
s Immeciatelyv wipe up any spilled gasoline.
o
eaks and clamps are
Clean engi
matter.
* Keep finished surfaces and wheels free of all gasoline,
oil, etc. |
s Protect painted surfaces with automotive type wax.
We do not recommend using a garden hose to clean your
tractor unless the electrical system, muffler, air filter and
carburetor are covered to keep water out. Water in engine
can result in a shortened engine life.
ry, seat, finish, etc. of all foreign
Mower will be easier to remove from the right side of tractor.
Place attachment clutch in position.
owertoits
Move attachment lift leverforward to lower m
lowest position. |
Roll belt off engine pulley.
Disconnect clutch rod from clutch lever by removing
retainer spring.
ERE
ayy
removing retainer spring.
+ Disconnect suspension arm 5 from rear deck brackets
by removing retainer spring
e Disconnect front links from dock by removing retai ner
springs.
е Raise lift lever to raise suspension arms.
out from under tractor.
MPORTANT: IF AN ATTACHMENT OTHER THAN THE
OWER DECK IS TO BE MOUNTED ON THE TRACTOR,
Slide mower
REMOVE THE FRONT LINKS.
ы si de mower under tractor ih di ischarge cardo to right
side of tractor. |
* Lower lift lever to its lowest position
e — Install mower in reverse order of removal instructions.
CLUTCH ROL
For” ar
и
% % a Pr esT
Up
a,
— CLUTCH LEVER
RETAINER
SPRINGS
tee”
PULLEY
fi PPT Et,
AA
Adjust the m
an veway.
mow stan nce “a on
both sides of mower should be the san n e or within 1/4"
of each other.
е If adjustment is necessary
side of mower only
= To raise one side ¢ у mower, tighten litt link adjustment
nut on that side.
» To lower one side of mower, loosen lift link adjustment
nut on that side.
= ee full urns of adjustment nut will change
make adjustment on one
OF MOWER TO
GROUND —_ —
о-в DJUSTMENT (See Figs. 19 and 20)
т; pes MUST BE LEVEL SIDE-TO- Si DE
US
EQUALLY SO MOWER
SIDE.
should be a
1/2" lower than the rear when the mower is in
position.
Check adjustment on right side of tractor. Measure dis-
tance “l В directly in front and behind the n andrel at bottom
edge of mower hous ing as shown.
¢ Before making any necessary adjustments, check that
both front i ks are equalin length. Bothlinks should be
approximately 10-3/8"
о If links are not equal in length, adjust one link to same
length as other link.
® То lower front of mower loosen nut “E” on both front
links an equal number of turns.
es When distance “D” is 1/8" to 1/2" lower at front than
rear, tighten nuts pre agal inst trunnion on both front
links.
« Toraise front of mower , loosen nut“F from trunnion on
both front links. Tighten n nut “E” on both front links an
equal number of turns.
When distance “D” is 1/8" to 1/2" lower at front than
rear, tighten nut “р” againsttrunnion on both front links.
* Recheck side-to-side adjustment.
d justed so that thet on is 5 approximately 1/8"
its highest
вен NUT sage
UE
lowest tachment
Roll belt o e engi
emoval.
Make sure belti grooves and inside all belt
guides,
sinall pulley ¢
| MANDREL
| PULLEY-
ar
E
E
SPRING
Your tractor is equipped 1
which is mounted on the ri
If tractor requires more
at high speed inhighe
ght side of the transaxle.
than six (6) feet stopping distance
st gear, then brake must be adjusted.
ergs
® Depress clutch/brake pedal ande eng ‘gage parking g brake.
e operating arm and
Measure distance betw
nut "A" on brake rod.
e Ifdistanceis otherthan 1-1/2", loose
nut "A" until distance becomes 1-1/2".
nut against nut "A"
« Hoadtesttractor for proper stopping distance as stated
| above Readjust if necessary. if stopping distance is
73
Rm
till greater than six (6) feet in highest gear, further
ai intenance is necessary. Contact your nearest au-
thorized service ce nte Fr,
TE ©
Park the tractor on level surface. Engage parking b brake.
For assistance, there is a belt installation guide decal on
bottom side of left footrest.
* Remove mower (See “TO
section of this manual.)
EMOVE MOWER” in this
= Remove. upper belt keeper.
* Remove belt from stationary idler and clutching idler.
* Pull belt slack toward rear of tractor. Remove belt
upwards from transaxle pulley by deflecting belt keep-
ers.
= Pull belt toward front of tractor and remove downwards
from around engine pulley.
* install new belt by reversing above procedure.
MAKE SURE UPPER BELT KEEPER IS
He UPPER BELT
KEEPER
whenw wheels 5 are 3
your tractor. |
wheel toe-in or caml
service center,
not lose).
Repair tire and reassemble.
On rear wheels only: align grooves in rear wheel hub
and axle. Insert square key.
s Replace washers and snap retaining ring securely in
axle groove. |
» Replace axle cover.
If your battery is
recharged. x
nai it should be
5 are used or el |
(+) terminal of each batter y
against chassis
e Connect one end of the BLACK cable to the |
TIVE (-) terminal of fully charged b
* Connect the other end of the BLACK cable to good
CHASSIS Gl away from fuel tank and battery.
TO REMOVE CAI
BLACK cable first from chassis is and then from the fully
charged battery.
s . RED cable last from both batteries
Ar
AL
e False hood.
® ul Guth holder ouf of the hole in the backside of the
Heplace bulb in holder and push bulb holder securely
iCkside of the grill.
эн
back into the hole in the be
» Close hood.
Loose or damaged wiring may cause your tractor to run
poorly, stop running, or prevent it from starting.
» Check wiring. See electrical wiring diagram in Repair
Parts section of this manual,
Heplace with 30 amp automotive-type plug-in fuse. The
fuse holder is located behind the dash.
Raise hood.
э Unsnap headlight wire connector.
Stand in front of tractor. Grasp hood at sides, tilt toward
engine and lift off of tractor.
* To replace, reverse above procedure.
WIRE
co NNECTOR
7 y to warm for five minutes. a
| 3 ents wit h engl ine running and shift/moti
control lever i in neutral (MN) position,
Move ih rottie control lever to slow
otate and hol dh rote lever a
e proie « ine be al
nil en
lever from choke (Py A . Release throttle leve er
® Check that holes 6 inc governorc an lever and ATION TES
“A” are not alig 1 ELER, TION TEST - |
loose n clamp screw andr move throttle cable until holes * Move throttle co ntrol lever from slow to fast (
are aligned. Tighten clamp screw securely. posit ion. If engine hesitates or dies, turn idle mixture
valve out (counte rclockwise) 1/8 turn. Repeat test and
continue to adjust, | if necessary, until eng! ine acceler-
ates smoothly
High speed stop is factory
damage may result.
IM ANT: NEVER TAMPER WITH THE ENGINE
GOVERNOR, WwW RICA IS FACTORY SET FOR PROPER
ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE
THE FACTO a AY HIGH SPEED SETTING CAN BE
DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED
HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR
NEAREST AUTHORIZED SERVICE CENTER/
DE PARTMENT, WHICH HAS PROPER EQUIPMENT AND
EXPERIENCE TO MAKE ANY NECESSARY
ADJUSTMENTS.
ao
adjusted. Do not adjust -
IDLE SPEED
HOLES "A"
) e factory and adjust-
ment should not be necessary. However, minor adjust-
ment may be requiredto co mpen nsate fordifferences in fuel,
temperature, altitude or load. If the carburetor does need
adjustment, proceed as follows:
in general, turning idle mixture valve in (clockwise) de-
creases the supply of fuel to the engine giv Ing: сапе or fuel
air mixture. Turning the idle mix ot t
clockwise) increases the suppl y of fuel to the e
a richer fuel a ir mi ture.
THE EAT IN CARBUR RETO R MA
TURNED IN TOO TIGHT.
RELIMINARY SE G-
е Aircleaner assembly must be assembled to the carbu-
retor when making carburetor adjustments.
Be sure the throttle control cable is adjusted properly
(see above).
With engine off turn idle mixture valve in (clockwise)
closing it finger tight and then turn out (counterciock-
wise) 1 full tum.
season УЕ if the tractor will not be used for 30 days or
TES
mower IS 10 be stored for a period of tim
oughly, r remove all
nter storage. When
ie, clean it thor-
store in a
dirt, grease, leaves, etc.
clean, dry area.
6
NING" in the Custom
Responcibi bi lities sect on of this n anual).
Inspect and replace belts, if necessary (S ве belt re-
placement instructions in the Service and Adjustments
sect ion of this mana)
Hesponsibilities
section of thi is manual.
Be sure that all nuts, bolts and screws are securely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary
Touch up all rusted or chi ipped paint surfaces; sand
lightly before painting.
Fully charge the battery for storage.
After a period of time in storage, battery may require
recharging.
To help prevent corrosion and power leakage during
long periods of storage, battery cables should be
disconnected and battery cleaned thoroughly (see “TO
CLEAN BATTERY AND TERMINALS” in the Cus-
tomer Responsi ibilities section of this manual).
After cleaning, leave cables disconnected and place
cables where they cannot come in contact with battery
terminais.
Be sure battery drain tube is securely attached.
if battery is removed from tractor for storage, do not
store Бане ry directly on concrete or damp su races.
ES THA T NG STO! HOL BLEN
SASOHOL OR USING ETHANOL OR
OL) CAN ATTR Se ois RE WHICH LEADS
e Neveruse engine or carburetor cleaner products inthe
fuel tank or permanent damage may occur.
Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits during stor-
age. Add stabilizer to gasoline in fuel tank or storage
container. Always follow the mix ratio found on stabilizer
container. Run engine at least 10 minutes after adding
stabilizer to allow the stabilizer to reach the carburetor. Do
not drain the gas tank and carburetor if using fuel stabilizer.
®
Drain oil (with engi ine warm) and replace with clean engine
oil. (See “ENGINE” in the Customer Responsibilities
section of this manual).
a Pour one ounce ю oil through spark plug hole(s) into
cylinder(s).
* Tumignition key to START” position fora few seconds
to distribute oil,
* Replace with new spark plug(s).
gasoline from one season lo another,
® Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
* If possible, store your tractor indoors and cover it to
give protection from dust and dirt
* Cover your tractor with a suitable protective cover that
does not retain moisture. Do not use plastic. Plastic
cannot breathe which allows condensation to formand
will cause your tractor to rust.
WNT: NEVER COVER TRA CT OR WHILE ENGINE
EX HAU ST AREAS ARE STILL WARM.
NOU EWN
©
эй
©
Out of fuel,
Engine not “CHOKED” properly.
Engine flooded.
Bad spark plug.
| air filter.
Dirty fuel filter,
Water in fuel.
Loose or damaged wiring.
Carburetor out of adjustment.
Engine valves out of adiustment.
с ово MO ee
©
10.
FIN fuel tank,
Sec TO START ENGINE in Operation section,
Wall several minutes before attempting to start.
eplace spark plug.
| Clean/replace air filter.
Replace fuel filter.
Drain fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter,
Check all wiring.
See “To Adjust Carburetor” In Service Adjustments
section.
Contact an authorized service center/department.
SO Wh
©
y air filter.
Bad spark plug,
Weak or dead battery.
Dirty fuel filter.
Stale or dirty fuel.
Loose or damaged wiring.
Carburetor out of adjustment.
Engine valves out of adjustment.
NOGAONT
ыы
Clean/replace air filter.
Replace spark plug.
Flecharge or replace battery.
Replace fuel filter,
Drain fuel tank and refill with fresh gasoline.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments’
section.
Contact an authorized service center/department.
Engine will not turn over
© 60 4 (5 сл № 62 № +
Ciutch/brake pedal not depressed.
Attachment cluich is engaged.
Weak or dead battery.
Blown fuse.
Corroded battery terminals.
Loose or damaged wiring.
Faulty ignition switch.
Faulty solenoid or starter.
Faulty operator presence switch(es).
DD SE A YN
Depress clutch/brake pedal.
Disengage attachment clutch,
Recharge or replace battery.
Heplace fuse.
Clean battery terminals.
Check all wiring.
Check/replace ignition switch.
Check/replace solenoid or starter.
Contact an authorized service center/department.
“ngîne clicks but will not
start
AN
Weak or dead battery.
Corroded battery terminals.
Loose or damaged wiring.
Faulty solenoid or starter.
© № =
Recharge or replace battery.
Clean battery terminals.
Check all wiring.
Check/replace solenoid or starter.
Loss of power
ю о мо ть YN
Cutting too much grass/too fast.
Throttle in “CHOKE” position.
Build-up of grass, leaves and trash under mower.
Dirty air filter.
Low oil level/dirty oil.
Faulty spark plug.
Dirty fuel filter.
Stale or dirty fuel,
Water in fuel.
Spark plug wire loose.
Dirty engine air screenfi
Dirty/clogged muffler.
Loose or damaged wiring.
Carburetor out of adjustme
nt.
Engine valves out of adjustment.
© 0 ND GS WN
#
Set in Higher Cul” position/reduce speed.
Adjust throttle control.
Clean underside of mower housing.
Clean/replace air filter.
Check oil level/change oil. .
Clean and regap or change spark plug.
Replace fuel filter.
Drain fuel tank and refill with fresh gasoline. |
Drain fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter. |
Connect and tighten spark plug wire.
Clean engine alr screen/fins.
Cleanvreplace muffler.
Check all wiring.
See “To Adjust Carburetor” in Service Adjustments
section, | |
Contact an authorized service center/depariment.
0 В
Worm, bent ar loose blade.
Bent blade mandrel.
Loose/damaged part(s).
Heplace blade. Tighten blade bolt.
Replace blade mandrel.
Tighten loose pari{s). Hepiace damaged parts.
Engine continues to run 1. Faulty operator-safety presence control system. 1. Check wiring, switches and connections. if not
l ator leaves seat corrected, contact an authorized service center
ent clutch riment.
Pocr cut - uneven 1. Worn, bent or loose blade. 1. Replace blade. Tighten blade bolt.
2. Mower deck not level. 2. Level mower deck.
3. Buildup of grass, leaves, and trash under mower. 3. Clean underside of mower housing.
4. Bent blade mandrel. | 4. Heplace blade mandrel.
5. Clogged mower deck vent holes from buildup of 5. Clean around mandrels to open vent holes,
grass, leaves, and trash around mandrels.
Mower blades will not 1. Obstruction in clutch mechanism. 1. Remove obstruction.
rotate 2. Worm/damaged mower drive belt. 2. Replace mower drive belt.
3. Frozen idler pulley. 3. Replace idler pulley.
4. Frozen blade mandrel. 4. Replace blade mandrel.
Poor grass discharge 1. Engine speed too slow. 1. Place throttle control in “FAST” position.
2. Travel speed too fast. 2. Shift to slower speed.
3. Wet grass. 3. Allow grass to dry before mowing.
4. Mower deck not level. 4. Level mower deck.
5. Low/uneven tire air pressure. 5. Check tires for proper air pressure.
6. Worn, bent or loose blade. 6. Replace/sharpen blade. Tighten blade boli.
7. Buildup of grass, leaves and trash under mower. 7. Clean underside of mower housing.
8. Mower drive belt worn. 8. Replace mower drive belt. |
9. Blades improperly installed. 9. Reinstall blades sharp edge down.
10. Improper blades used. 10. Replace with blades listed in this manual.
11. Clogged mower deck vent holes from buildup of 11. Clean around mandrels to open vent holes.
grass, leaves, and trash around mandrels.
Headiight(s) not working 1. Switchis “OFF”, 1. Turn switch “ON”.
(if so equipped) 2. Bulb{s) bumed out. 2. Replace bulb(s).
3. Faulty light switch. 3. Checl/replace light switch.
4. Loose or damaged wining. 4. Check wiring and connections.
5. Blown fuse. 5. Heplace fuse.
Battery will not charge 1. Bad battery cell(s). 1. Replace battery.
| 2. Poor cable connections. 2. Check/clean all connections.
3. Faulty regulator (if so equipped). 3. Replace regulator.
4. Faulty alternator. 4. Replace alternator.
Engine “backfires” 1. Engine throttle control not set at “SLOW” 1. Move throttle control to “SLOW” position and allow
when turning engine
position for 30 seconds before stopping engine.
to idie for 30 seconds before stopping engine.
RED
BLACK
BATTERY
RED
RED
SWITCH
BLACK
IGNITION |
WHITE
J
FUSE 30 AMP. STARTER
SOLENOID
CLUTCH / BRAKE |
(PEDAL UP) | WHITE
SEAT SWITCH
(NOT OCCU PIED)
BLACK >
‘свои NDING
CONNECTOR
CLUTCH C FF)
NANA
\
a
=
E
zu
=
Sa
=)
yr
TC
==
©
ин
| /
HOUR |
METER O
(OPTIONAL)
BLACK © GNTION О A.
ARK (Y A GAP
O UNIT (2 PLUGS ON
TWIN CYL. ENGINES)
CHARGING SYSTEM OUTPUT
£ 28 VOLTS AC MIN. € 3600 RPM
3 AMP DC @ 3600 RPM (CHARGING SYSTEM DISCONNECTED)
BLUE
LIGHTING SYSTEM OUTPUT (ODE ALTERNATOR
ORANGE. 5 AMP AC @ 3600 RPM O)
[E Wa | чжны ны |
POSITION
OFF |G+M+L
RUN/LIGHT| B+L
RUN B+L
START |B+L+5
14 VOLTS AC MIN. € 3600 RPM (LIGHTS OFF)
HEADLIGHTS
BROWN
YOUR TRACTOR IS
EQUIPPED WITH A SPECIAL
ALTERNATOR SYSTEM
THE LIGHTS ARE NOT _ - —
CONNECTED TO THE NON-REMOVABLE REMOVABLE
BATTERY, BUT HAVE THEIR CONNECTIONS CONNECTIONS ///
OWN ELECTR ICAL SOU НО.
BECAUSE OF THIS, THE
BRIGHTNESS OF THE LIGHTS
VILL CHANGE WITH ENGINE
SPEED. AT IDLE THE LIGHTS S WE -
WILL DIM. AS THE ENGINE IS SEF VICING OF UN
IT, THEY
SPEEDED UP, THE LIGHTS - SHOULD BE REPLACED TO
WILL BECOME THEIR BRIGHTEST. PROPERI Y SECURE YOUR
WIRING.
NOTE: All component dimensions give in U.S. inches
62 ©) ГО РО РО ЛО РО ГО MN
— 0 E 60 OY OF fo PY +
Es La La La Pa da бо со
СО £a ON — OWN
> сл
Ov
В} нана mo
O С) SD NE Сю РО —
144925
74760412
19091016
10040400
73220400
109238X
156417
109596
147688
153664
10090400
73350400
136850
4152J
4799.)
146147
108824X
4207J
121305X
140301
124211X
141226
122147X
156442
71110408
131563
145673
73640400
140844
141940
140413
Battery 12 Volt 25 AMP
Bolt Hex Hd 1/4-20unc X 3/4
Washer 9/32 X 5/8 X 16 Ga
Washer Lock Hvy Helical 1/4
Nut Fin Hex 1/4-20 Unc
Tube Plastic 12"
Case Battery Mech Hinge
Clamp Hose Olive
Fastener Snap- in
Switch Interlock Push-In
Washer Lock 1/4
Nut Jam Hex 1/4-20 Unc
Harness Asm Light W/4152;
Bulb Light #1156
Cable Battery 6 Ga 11" red
Cable Battery 6 Ga red w/16 Wire
Fuse 30 AMP Auto Green
Cable Ground 6 Ga 12" black
Switch Plunger Nc Gray
Switch Ign 4 pos
Nut Ignition |
Cover Sw Key Blk 1 25 Text SLT
Key Ign Molded |
Harness Ign Man CL AM HM 97
Bolt Blk. Fin Hex 1/4-20 Unc x 1/2
Cover Terminal Red
Solenoid
Nut Keps Blk Hx 1/4-20 Unc
Adapter Ammeter Rectangular
Protection Wire Loop
Harness Engine B&S Tec Dual
{inch =254 mm
La WON Y UY 00 CD Сл Ja QD NS +
ES CO E ÓN La E
E CD O7 La LY
LT OT OT
Lo Po —
o
O >
57
155051
140356
17490612
19131216
155272
155924X011
155138
147627X011
72140608
° 155927
145660
155934X010
17490608
74180512
73510500
74780616
19131312
73800600
157539
150209
109872X550
136619
105476X550
105475X550
72110606
139886
139887
73800400
19091416
144697
17030814
144696
74780412
140 158418
ame ны:
54793
Chassis Assembly
Drawbar |
Screw, Thd. Roll. 3/8-16 x 3/4
Washer 13/32 x 3/4 x 16 Gauge
Bumper Hood/Dash
Saddle |
Clip Retainer Slide-On
Dash
Bolt, Carriage 3/8-16 x 3/4
Panel, Dash, L.H.
Clip Tinnerman Grille P/L
Panel, Dash, R.H.
Screw Thdrol 3/8-16 x 1/2
Screw, Machine, Truss Head
5/16-18 UNC x 3/4
Nut
- Hood Assembly
Bolt
Washer 13/32 x 13/16 x 12 Gauge
Nut
Grill |
Lens, Grille
render
Bracket, Fender Support
Footrest, L.H.
Footrest, R.H,
Bolt |
Pivot Bracket Assembiy, L.H.
Pivot Bracket Assembiy, R.H.
Nut Lock, w/lnsert 1/4-20 Unc
Washer 9/32 x 7/8 x 16 Ga.
Bracket Grille Lh
Screw Spiderlock Hex Hd #8-7/8
Bracket Grille Rh |
Bolt Fin Hex 1/4-20 Une x .75
Bracket Suspension Front
Plug, Button
: All component dimensions given in U.S. inches
1 inch = 25.4 mm
coh md
wd 3 0 > CD UTE OO PO
ely dy ends do md ond
O 00 UT WN
o
lt
ГО ID IQ
CD Où £a NO
ГО о
o
VU 60 60 O0 ON
©) сл оф D — © ©
PC
+ (3 0 00 4
146682
123666X
12000028
121520X
17490512
130802
131679
76020416
105701X
19151216
74550412
10040400
74490544
74780616
73800600
106933X
130804
73350600
106888X
19131316
76020412
145204
71673
130807
127275X
74760512
155071
120183X
19211616
1572H
123674X
74760644
4470J
154777
Sprin gl R
Pull ley Transaxle Alum
Hing Retainer # 5100-62
Strap Pnt Torque 30 Deg Blk
Screw Thdrol 5/16-18 X 3/4 Tyt
Plate Pnt Rod Shift T/a (blk)
Hod Shifter Blk —
Pin Cotter 1/8 X 1 Cad
Washer Plate Shf 388 Sq Hole
Washer 15/32 X 3/4 X 16ga
Bolt 1/4-28unf Gr8 w/Patch
Washer Lock Hvy Helical 1/4
Bolt Hex FLGHD 5/16-18 Gr.5
Bolt Fin Hex 3/8-16 Unc x 1 Gr. 5
Nut Lock 3/8-16 Unc
Knob Rd 1/2-13 Distr Thds Rik
ЧА Bnd 0 FAT ES
Hod Brake Lt
Nut Hex Jam 3/8-16 Unc
Spring Rod Brake 2 00 Zinc
Washer 13/32 X 13/16 X 16 Ga
Pin Cotter 1/8 X 3/4 Cad
Rod Brake Parking Li/Yt
Cap Parking Brake Red
Bracket Transmission
Keeper Belt Lh Lt 14 Ga
Bolt Fin Hex 5/16-18 x 3/4
Shaft Asm Pedal Foot
Bearing Nylon Blk 629 Id
Washer 21/32 X 1 X 16 Ga
Fin Roll 3/16 X 1°
Pulley Idler Flat
Bolt Fin Hex 3/8-16unc X 2- 3/4
Spacer Spli it 395 X 59 Bzp
Keeper Belt Idler Fool Proof
42
47
49
50
51
52
53
54
55
56
57
58
59
61
62
63
64
65
66
70
12
74
75
76
77
78
79
96
112
113
116
118
121
19131312
127783
154604
123205X
74760624
73680600
73680500
105710X
2751R
105709X
74760620
130801
127274 X
140312
17490612
3883H
140186
71170764
10040700
154778
134683
19132012
137057
121749X
12000001
123583X
121748X
2228M
4497H
19091210
127285X
72110610
154774
154419
Washer 13/32 X 13/16 X 12 Ga
Pulley Idler V Groove Plastic
Bellcrank Asm Clutch
Retainer Belt Style Spring
Bolt Hex Hd 3/8-16unc X 1-1/2
Nut Crownlock 3/8-16 Unc
Nut Lock 5/16-18 Unc
Link Clutch 7 66
Clip Line Fuel
Spring Return Clutch 6 75
Bolt Fin Hex 3/8-16unc X 1-1/4
V-belt Ground Drive 95.25
Keeper Belt Rh Lt Pnt/zinc 16g
Retainer Belt Chassis Lh Zinc
Screw Thdrol 3/8-16x3/4 Ty-it
Cover Pedal Blk Std —
Pulley Engine
Bolt Finhex 7/16-20 x 4 g5
Washer Lock Hvy Hicl Spr 7/16
Keeper Belt Engine Fool Proof
Guide Belt Dr Mower Rh
Washer 13/32 X 1-1/4 X 12 Ga
Spacer Axle
Washer 25/32 X 1 1/4 X 16 Ga
Ring E 45133-75
‘Key Square 20 X 1845/1865
Washer 25/32 X 1 5/8 X 16ga
Key Woodruff
Retainer Spring
Washer 8/32 X 3/4 X 10 Ga
Strap Torque Lt
Bolt Rdhd Sgnk 3/8-16 x 1.25
Spacer Bellcrank
Nyliner Clutching SLT
: All component dimensions given in U.S. inches
{inch = 25.4 mm
© ©О 09 Y ISA OH 00 OO DO A
Г о
DJ
NJ
м
Жены бы”
22 62 ENTES
DRO ODM
50 со
XD >
D E DD BED LL La Pads La BO
140044
154427
154422
154423
6266H
121748X
19272016
12000029
3366R
156438
10040600
73901000
156546
57079
124035X
126684 X
10040400
71100410
127501
154406
126847X
136874
19131416
17490612
76020412
130465
155099
152927 -
140045
19133808
7810H
100711L
145054
121749X
153720
121232X
6855M
73800500
74780520
156594
74780616
154780
154404
Steering Wheel
Front Axle Assembly
Spindle Assembly, LH.
Spindle Assembly, R.H.
Bearing, Race, Thrust, Hardened
Washer 25/32 x 1-5/8 x 16 Gauge
Washer 27/32 x 1-1/4 x 16 Gauge
Ring, Klip
Bearing, Steering Column
Link, Drag
Washer, Lock
Bearing, Axle |
Nut, Lock, Flange 5/8-11 UNC
Shaft Assembly, Steering
Washer, Thrust ‚515 x .750 x .033
Support, Shaft
Washer, Shim 1/4 x 5/8 x .062
Washer |
Screw, Cap Socket Head Phos 8 Oil
Pittman Shaft Assembly
Bracket, Steering
Bushing, Link, Drag
Gear, Sector
Washer 13/32 x 7/8 x 16 (Gauge
Screw, Thd., Roll. 3/8-16 x 3/4
Pin
Rod, Tie
Bushing, Steerin ng
Screw TT #10-32 5 3/8 Flange
Insert, Steering Wheel
Washer 13/32 x 2- 3/8 x 8 Gauge
Gripco Nut
Adaptor, Steering Wheel
Boot, Steering Dash P/L Mtl Blk
Washer 25/32 x 1-1/4 x 16 Gauge
Extension Steering
Cap, Spindle
Fitting, Grease
Nut Lock Hx w/ins. 5/16-18 Unc
Bolt Fin Hex 5/16-18 Unc x 1-1/4
Kit, Steering Assembly, Service
Bolt, Fin Hex 3/8-16 Unc x 1 Grade 5
Spacer, Axle
Bo Fin Hex 5/8. 11 Unc x 2-3/4
Brace, Axle
: All component dimensions given in U.S. inches
{inch = 25.4 mm
1
2
3
4
5
6
7
8
9
10
12
13
127426X
140551
74760616
19131610
145006
73800600
124181X
17490616
19131614
155925
121246X
121248X
Seat V250
Bracket Pnt Pivot Seat (blk )
Bolt Fin Hex 3/8-16unc X 1
Washer 13/32 X 3/4 X 10 Ga
Clip Push In Hinged
Nut Crownlock 3/8-16 Unc
Spring Seat Cprsn 2 250 Blk Zi
Screw Thdrol 3/8-16 X 1 Ty-tt
Washer 13/32 X 1 X 14 Ga
Pan Pnt Seat (blk )
Bracket Pnt Mounting Switch
k Nyl 50 id
Bushing Snap В!
14
15
16
17
21
22
23
24
25
26
#
A
”
7 .
o PTA Мы Мене A A AA a A E но еее
/
BT,
/
У
7 q
#
Gm aan
#
ñ
x # +
72060411
134300
121250X
123976X
153236
73800500
74780814
19171912
127018X
10040800
Bolt Rdhd Sht Nk 1/4-20x1-3/8
Spacer Split 28 X 96 Zinc
Spring Cprsn 1 27 Blk Pnt
Nut Lock 1/4 Lge Fig Gr 5 Zinc
Bolt Shoulder 5/16-18 Unc Blkz
Nut Crown Lock 5/16-18
Bolt Fin Hex 1/2-13 X 7/8 Gr 5
Washer 17/32 X 1-3/16 X 12 Ga
Bolt Shoulder 5/16-18 X 62
Washer Lock Hvy Hicl Spr 1/2
: All component dimensions given in U.S. inches.
1 inch = 25.4 mm
onside
158271
272632
156609
156610
156604
158315
158437
156602
145005
Decal Oper Sdi Gear Dr. Eng/Span
Decal Engine Hp
Decal Hood Rh
Decal Hood Lh
Decal Ins Strg Wh
Decal Seat Heplacement
Decal Panel Side Speed/Dejck Size
Decal Fender Logo
Decal Bry Dngr/Psn
11
12
15
17
18
19
ur
us
ms
jd ond
‚о =® СО 92 00 1 СВ Сл фо С РО >
157141
141897
136832
158316
158436
158435
138311
157394
1577416
59192
65139
106222X
59904
106732X427
278H
9040H
106108X427
124635X
7152J
104757X
144334
Decal Fender Danger
Decal Clutch/brake Eng/Span
Decal Mower Drive Schematic 38
“Decal Engine Replacement
Decal Mower Home Weed Envir
Decal Fend Sd 5Sp Lawn Tractor
Decal Lift Handle
Manual, Owner's (English)
Manual, Owners (Spanish)
Cap Value Tire
stem Value
Tire F Ts 15 X 6 0 - 6 Service
Tube Inner Front #35060
Rim Asm 6"front White Service
Fitting Grease
Bearing Flange |
Rim Asm 8"rear White Service
Tire À Ts 18x8 5-8 Service
Tube Rear 95 X 8 Service
Cap Axie Blk 150 X 100
Sealant, Tire (10 oz. Tube)
E: All component dimensions given in U.S. inches.
1 inch = 25.4 mm
1
2
3
13
14
15
16
23
29
31
32
33
35
37
38
40
44
46
62
72
78
81
140310
17720410
ar me Mh ee om we mm
137348
272293
13280324
13200300
11050600
156123
137180
109202X
140527
123487X
17490512
AMAN
TA
BE OO NO ARO A E
124028X
17490412
19091416
10040500
71070512
17490620
128861
Control Throt/Ch 23 5 Lh Flag
Screw Hex Thd Cut 1/4-20x5/8
Engine (See Breakdown) B&S
Mod el No. 289707- 01 79-0
Muffler Exhaust B&S Lt
Gasket 1 313 id Tin Plated
Nipple Pipe 3/8 Npt X 3"
Elbow Std 80 Degree 3/8-18 Np
Washer Lock Ext Tooth 3/8
Shield Browning
Arrestor Spark
Tank Fuel 1 25 Fr
Cap Asm Fuel Top Vent n/Lany
Clamp Hose Blk
Screw Thdrol 5/16-18 x 3/4
Line Fuel 20"
Plug Oil Drain (Order From Engine
Manufacturer)
Bushing Snap Ny! Blk Fuel Line
Screw Hexwsh Thdrol 1/4-20x3/4
Washer 9/32 X 7/8 X 16ga
Washer Lock Hvy Hicl Spr 5/16
Screw Hexhd Cap 5/16-18x3/4
Screw Thdrol 3/8-16x1-1/4 Tytt
Nut Flange 1/4-20 Starter Nut
All | component dimensions given in U.S. inches
1 inch = 25.4 mm
erty
RJ cmb cod coud ный, de cod
CD CO ON
31
32
pr
© 0 OUT СО ГО —+
136973
145117
105767X
12000002
19211621
120183X
109413X
124526X
122512X
139865
139866
4939M
127218
73350800
130171
73800800
139868
3146R
140302
73540600
Spring Cprsn
Rod Asm. Lever
Shaft Asm. Lift
Pin Groove |
E Ring #5133-62
Washer 21/32 x 1 x 21 Ga.
Bearing Nylong
Grip Handle bicycle Matte
Button Plunger Black
Lift Asm, Link LH
Lift Asm. Link RH
por iner Spring
Link Front
Nut Jam Hex 1/2-13 Unc
Trunnion Blk Zinc |
Nut Lock W/Wsh 1/2-13 Unc
Arm Suspension Mower
Retainer Spring
Bearing, Pvt. Lift. Spherical
Nut Crownlock 3/8-24
: All component dimensions given in U.S. inches
1 inch = 25.4 mm
codo md md ma
Cad NG + TL ON СВ CT £a CO 1 ae
words md a o
E CD Di
AO BD DO
ta 13 —
pe ве
3 3 3 05 PO TO O PO №
ГО = © (О со —4 С) С
со
со
TT TL SL DD
a WW —À Om
142829
72140506
138017
138440
4939M
130832
850857
10030600
140296
1 29895
137645
128774
110485X
140329
132827
‚| 73660500
137607
105304X
123713X
110452X
106736X
19111016
106735X
138776
129963
153532
137266
131494
73680600
133551
133504
4497H
130840
133943
133840
Mower Housing Assembly
Bolt, Carriage 5/16-18 x 3/4
Bracket Asm. Fram Sway Bar 38/42
3 Bracket, Asm. Deck Sway Bar 38”
Retainer, Spring
Asm. Suspensi on Rear
Bolt, Hex 3/6-24 x 1-1/4 Grade 8
Washer, Lock, Hvy Hicl &
Washer ‚Hard E: Blade M ower Ve nted
Blade, | Mower, 38" .
Ball Beari ing
Shaft and Bearing Assembly
(Includes Key Number 15)
Mandrel Housing, Vented
Ball Bearing, Mandrel
Stripper, Mower, Vented
Bolt, Shoulder
Nut, Crownlock 5/16-18 -
Bracket, Mower Deflector
Cap, Sleeve
Spring, Deflector
Nut, Push
Shield, Deflector
Washer 11/32 x 3/4 x 16 Gauge
Rod, Hinge
Screw, Thdrol Hex Hd
Washer, Spacer
Fulley, Mandrel
Nut, Flangelock 9/16
Pulley, Idler, Flat |
Nut, Crownlock 3/8-16
Rod, Pivot |
Rod, Clutch, Secondary
Retainer, Spring
Brake Assembly
Washer Hardened
Idler Arm Assembly
56
67
68
69
71
72
73
74
75
76
77
78
79
80
81
82
86
87
88
89
Or
2 Lom
107
108
109
110
113
122
123
124
128
me
122052X
106932X
144200
76020312
142427
131870
127847
121748X
12000029
128903
127845
154809
127498
153701
73350600
142028
7631J
128772
19111216
19131612
73800600
133502
133503
74760640
142587
17490512
131289
131288
72110614
153390
130794
145758
Spacer, Hetainer 1-3/4
Knob
Belt
Pin, Cotter 3/32 x 3/4
Hod, Clutch, Primary
Spring, Retum
~ Arm, Clutch, Secondary
Washer 25/32 x 1-5/8 x 16 Gauge
Ri ing, Klip
Bolt, Shoulder
Keeper, Spring
Arm, Clutch, Primary
Bushing
Spring
Nut Hex Jam. 3/8-16 UNC
Trunnion Adj 94
Runner, LH
Runner, RH
Washer 11/32 x 3/4 x 16 Gauge
Washer 13/32 X 1x 12 Gauge
Nut Lock Hex + wit ns 3/8-16 UNC
Spacer, Retainer |
Stiffener, Idler Arm
Bolt, Hex Head 3/8-16 x 2-1/2
Upstop Deck Front 38"
Screw, Hex Head, Tha, Roll.
5/16- 18 x 3/4
Rod, Brake, LH
Rod, Brake, RH
Bolt, Carriage 3/8-16 x 1-3/4
Washer Felt
‘Mandrel Assembly (Includes Key
Numbers 12-15, 17-19, 31 and 33)
Mower Deck, Complete
IOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm -
со
Om OOD GRY
JS
md {7
DJ la md md cd md сон
5 0040 Wh
о
—
`2
1
voa trans
О РО
сл бо
780086
770102A
776260
778139
778136
792136A
792047
784352
754355
778229
778113A
778221
778068
778260
786139
780102
792077
792078
792079
788061
792073
792125
792035
788040
780072
780108
780001
792001
788095
7801054
780118A
790003
790007
799021
786026
792076A
790079
792073
424 792085A
Cover, Transaxie
Bearing, Needie
Case, Transaxie
Shaft, Counter
Shaft and Pinion Assembly, Output
Gear, Output
Gear, Spur, 15 Teeth
Key, Shift
Key, Woodruff
Collar, Shifter
Rod and Fork Assembly, Shift
Gear, Bevel, 42 Teeth
Bevel Pinion, Input
Gear, Bevel
Gear, Bevel Pinion
Gear, Ring
Pin, Drive
Spacer, Neutral
Ball, Steel 5/16" diameter
Set Screw 3/8-16 x 3/8
Spring
Ring, Seal
Screw, Flanged Hex Head, Thread
Forming 1/4-20 x 1-1/4
Ring, Retainer
(4 Required, Package of 3)
Ring, Retainer
Ring, Retainer
Washer, Thrust
Washer, Thrust
Washer
“Oy” Ring
Seal, Square Cut
Bushing, Flanged
Bushing, Flanged
Disk, Brake
Plate, Brake Pad
Pad, Brake
Pin, Dowei
Washer, Flat
Lever, Brake
Screw, Flanged Hex Head, Thread
Forming 1/4-20 x 1-1/4
Screw 1/4-20 x 2-1/4
786066
786086
774690
774691
778215
778124A
778123A
778122A
778273
778230
778126A
778127A
778128A
778163
786071
786072
780109
776135
776315A
786116A
780051
786118
788069
792165
788091
780090
788078A
792144
786081
786082
786123
788067B
792166
792167
510334
734528A
MPTION
Locknut 5/16-24
Holder, Brake Pad
Spacer
Axle 11 5/16" ong.
Axle 16-1/2" long
Gear, Spur, 37 Teeth,
Gear, Spur, 30 Teeth (
Gear, Spur, 25 Teeth (
Gear, Spur, 22 Teeth (
Gear, Spur, 19 Teeth,
Gear, Spur, 12 Teeth (
Gear, Spur, 20 Teeth (
(
(
Steel (14)
Ze)
Зе)
4»)
Steel (Sr)
«)
)
)
)
)
E
Gear, Spur, 25 Teeth
Gear, Spur, 28 Teeth
Gear, Spur, 31 Teeth
Spacer
Spacer
Washer, Thrust
Shaft, Input
Shaft, Brake, 4 Keved
Plug
Washer, Thrust
Spacer
seal, Square Cut
Plug, Threaded 9/16-18
“O” Ring
Washer, Thrust
4
th
1
2e
Ir
4
5
th
‘Ring, Hetaining, Inverted
(Package of 2)
Spring, Brake
Chain, Roller
(Number 41 Chain, 24 Links)
Sprocket, 9 Teeth (Reverse)
Sprocket, 18 Teeth (Reverse)
Grease, Bentonite, 32 Ounce Bottle
Screw 1/4-20 x 2
Locknut 1/4-20
Gasket Eliminator (Loctite #515)
Replacement Transaxie
: All component dimensions given in U.S. inches
1 inch = 25.4 mm
Parts must be ordered from Tecumseh Products Co.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement