Model No. 831.23880.0

Serial No.

Write the serial number in the space above for reference.

Serial Number

Decal (under frame)

•• Assembly

•• Operation

•• Maintenance

•• Part List and Drawing

HYBRID TRAINER

User’’s Manual

Sears, Roebuck and Co.

Hoffman Estates, IL 60179

CAUTION

Read all precautions and instructions in this manual before using this equipment. Keep this manual for future reference.

TABLE OF CONTENTS

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

HOW TO USE THE HYBRID TRAINER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

ORDERING REPLACEMENT PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

90 DAY FULL WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

WARNING DECAL PLACEMENT

This drawing shows the location(s) of the warning decal(s).

If a decal is missing or illegible, call 1-888-533-1333 and request a free replacement decal. Apply the decal in the

location shown. Note: The decal(s) may not be shown at actual size.

2

IMPORTANT PRECAUTIONS

WARNING:

To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your hybrid trainer before using your hybrid trainer.

Sears assumes no responsibility for personal injury or property damage sustained by or through the use of this product.

1. It is the responsibility of the owner to ensure that all users of the hybrid trainer are adequately informed of all precautions.

persons weighing more than 350 lbs.

(159 kg).

2. Before beginning any exercise program, consult your physician. This is especially important for persons over age 35 or persons with pre-existing health problems.

10. Wear appropriate clothes while exercising; do not wear loose clothes that could become caught on the hybrid trainer. Always wear athletic shoes for foot protection while exercising.

3. Use the hybrid trainer only as described in this manual.

4. The hybrid trainer is intended for home use only. Do not use the hybrid trainer in a commercial, rental, or institutional setting.

5. Keep the hybrid trainer indoors, away from moisture and dust. Do not put the hybrid trainer in a garage or covered patio or near water.

6. Place the hybrid trainer on a level surface, with at least 3 ft. (0.9 m) of clearance in the front and rear of the hybrid trainer and 2 ft.

(0.6 m) on each side. To protect the floor or carpet from damage, place a mat under the hybrid trainer.

7. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.

8. Keep children under age 12 and pets away from the hybrid trainer at all times.

9. The hybrid trainer should not be used by

11. Hold the handlebars or the upper body arms when mounting, dismounting, or using the hybrid trainer.

12. Make sure that the pedal knobs are fully tightened each time you use the hybrid trainer.

13. The heart rate monitor is not a medical device. Various factors may affect the accuracy of heart rate readings. The heart rate monitor is intended only as an exercise aid in determining heart rate trends in general.

14. The hybrid trainer does not have a freewheel; the pedals will continue to move until the flywheel stops. Reduce your pedaling speed in a controlled way.

15. Keep your back straight while using the hybrid trainer; do not arch your back.

16. Over exercising may result in serious injury or death. If you feel faint or if you experience pain while exercising, stop immediately and cool down.

3

BEFORE YOU BEGIN

Thank you for selecting the revolutionary PROFORM ®

HYBRID TRAINER. The HYBRID TRAINER provides an impressive selection of features designed to make your workouts at home more effective and enjoyable.

manual. To help us assist you, note the product model number and serial number before contacting us. The model number and the location of the serial number decal are shown on the front cover of this manual.

For your benefit, read this manual carefully before

you use the hybrid trainer. If you have questions after reading this manual, please see the back cover of this

Before reading further, please familiarize yourself with the parts that are labeled in the drawing below.

Heart Rate Monitor

Handlebar

Console

Upper Body Arm

Console Knob

Water Bottle Holder*

Seat

Backrest

* Water bottle is not included

Pedal Brace

Pedal

Pedal Knob

Length: 6 ft. 4 in. (193 cm)

Width: 2 ft. 2 in. (66 cm)

4

PART IDENTIFICATION CHART

Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it has been preassembled. Extra parts may be included.

M6 Locknut

(51)––4

M8 Locknut

(10)––10

M10 Locknut

(48)––1

Wave Washer

(81)––4

M6 Curved

Washer

(25)––4

M8 Split

Washer

(42)––8

M8 Small

Washer

(93)––4

M8 Large

Washer (54)––4

M10 Split

Washer (98)––2

M10 Curved

Washer (39)––3

M4 x 16mm

Screw (47)––8

M6 x 30mm

Bolt (49)––4

M8 x 13mm

Screw (95)––6

M8 x 40mm Bolt (83)––6 M8 x 65mm Bolt (94)––2

M8 x 125mm Bolt (58)––2

M8 x 20mm

Screw (34)––4

M10 x 54mm Screw (97)––1 M10 x 25mm

Screw (96)––1

M10 x 60mm Bolt (61)––1 M10 x 65mm Screw (40)––4

5

ASSEMBLY

•• Assembly requires two persons.

•• Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until you  nish assembly.

•• Left parts are marked ““L”” or ““Left”” and right parts are marked ““R”” or ““Right.””

•• To identify small parts, see page 5.

•• In addition to the included tool(s), assembly requires the following tools: one Phillips screwdriver one rubber mallet

Assembly may be easier if you have a set of wrenches. To avoid damaging parts, do not use power tools.

1. Go to www.proformservice.com/registration on your computer and register your product.

•• activates your warranty

•• saves you time if you ever need to contact

Customer Care

•• allows us to notify you of upgrades and offers

Note: If you do not have Internet access, call

1-888-533-1333 and register your product.

1

2. With the help of a second person, place some of the packing materials (not shown) under the

Rear Frame (1). Have the second person hold the Rear Frame to prevent it from tipping while you complete this step.

Orient the Rear Stabilizer (6) so that the large holes are facing the Rear Frame (1). Attach the

Rear Stabilizer to the Rear Frame with two M10 x 65mm Screws (40).

Then, remove the packing materials from under the Rear Frame (1).

2

Large

Holes

40 6

1

6

3. Orient the Front Stabilizer (2) so that the large holes are facing the Front Frame (23). Attach the

Front Stabilizer to the Front Frame with two M10 x 65mm Screws (40).

3

Large

Holes

2

4. Set the Front Frame (23) near the Rear Frame

(1) as shown.

Locate the wire tie in the Front Frame (23). Tie the wire tie to the Main Wire Harness (45) in the

Rear Frame (1). Then, pull the upper end of the wire tie until the Main Wire Harness is routed through the Front Frame.

4

23 40

Wire Tie

7

1

Wire

Tie

23

45

5. Tip: Avoid pinching the Main Wire Harness

(45). Slide the Front Frame (23) onto the Rear

Frame (1).

Attach the Front Frame (23) with an M10 x

25mm Screw (96), an M10 Split Washer (98), and an M10 Curved Washer (39). Do not tighten the Screw yet.

Next, attach the Front Frame (23) with an M10 x 54mm Screw (97), an M10 Split Washer

(98), and an M10 Curved Washer (39). Do not tighten the Screw yet.

Then, attach the Front Frame (23) with an M10 x

60mm Bolt (61) and an M10 Locknut (48); make sure that the Locknut is in the hexagonal

hole. Do not tighten the Bolt yet.

See steps 2 and 3. Make sure that the ends of the Rear Stabilizer (6) and the Front Stabilizer

(2) are touching the floor.

Tighten the Bolt and the Screws (61, 96, 97).

5

Avoid pinching the Main

Wire Harness (45)

97

61

Hexagonal Hole

98

39

1

45

23

39

48

98

96

6. Hold the Console Post (73) near the Front Frame

(23) as shown. Insert the Main Wire Harness

(45) upward through the Console Post.

6

73

45

23

8

7. Tip: Avoid pinching the Main Wire Harness

(45). Slide the Console Post (73) onto the Front

Frame (23) and hold it in place.

Next, insert the Axle (80) into the Console Post

(73) and into the Front Frame (23). Center the

Axle.

Then, tighten the Console Knob (9) with an M10

Curved Washer (39) into the Console Post (73) and into the Front Frame (23).

7

Avoid pinching the Main Wire

Harness (45)

80

73

45

23

39

9

8. Identify the Left Upper Body Leg (74) and the

Right Upper Body Leg (86).

Using a plastic bag to keep your fingers clean, apply a generous amount of the included grease to each side of the Axle (80) and to two Wave

Washers (81).

Next, slide the two Wave Washers (81) and the

Upper Body Legs (74, 86) onto the Axle (80); make sure that the Upper Body Legs are on the correct sides.

Then, tighten an M8 x 20mm Screw (34), a Pivot

Cover (90), and an M8 Large Washer (54) into each end of the Axle (80) at the same time.

8

90

54

34

Grease

74

81

Grease

80

81

86

54

90

34

9

9. Identify the Right Pedal Carriage (64), which is attached to one of the Pedals (67). In addition, identify the Right Pedal Leg (71).

Loosen the Pedal Knob (70) on the right side of the Right Pedal Carriage (64), slide the Right

Pedal Carriage as far as possible onto the

Right Pedal Leg (71), and then tighten the

Pedal Knob.

Then, attach a Small Bumper (69) to the underside of the Right Pedal Leg (71) with an M4 x

16mm Screw (47).

Repeat this step with the Left Pedal Carriage

(65), the Left Pedal Leg (79), and the other

Small Bumper (not shown).

9

67

64

70

79

65

71

69

47

10. Apply a generous amount of grease to the axle on the Right Upper Body Leg (86) and to two

Wave Washers (81).

Next, slide a Leg Bushing (13), a Wave Washer

(81), and the Right Pedal Leg (71) with the Right

Pedal Carriage (64) onto the axle.

Then, tighten an M8 x 20mm Screw (34), a Pivot

Cover (90), and an M8 Large Washer (54) into the axle.

Repeat this step on the other side of the hybrid trainer.

10

34

90

54

86

71

81

13

Grease

64

10

11. Slide the Right Pedal Leg (71) onto the Right

Pedal Leg Bracket (75).

Attach the Right Pedal Leg (71) with three M8 x

13mm Screws (95) and three M8 Split Washers

(42). Start all three Screws, and then tighten them.

Repeat this step on the other side of the hybrid trainer.

11

64

42

71

75

95

12. Have a second person hold the Handlebar

(53) near the Console Post (73).

Insert the indicated wire tie into the hole in the side of the Console Post (73), and then pull the wire tie until the Pulse Wires (68) are routed through the Console Post.

Tip: Avoid pinching the wires. Attach the

Handlebar (53) to the Console Post (73) with two

M8 x 65mm Bolts (94), two M8 Split Washers

(42), and two M8 Locknuts (10).

12

10

73

45

53

42

94

68

Wire

Tie

Avoid pinching the wires

11

13. The Console (16) requires four AA batteries (not included); alkaline batteries are recommended.

Do not use old and new batteries together or alkaline, standard, and rechargeable batteries together. IMPORTANT: If the Console has been exposed to cold temperatures, allow it to warm to room temperature before inserting batteries. Otherwise, you may damage the console displays or other electronic

components.

Remove the battery cover from the back of the

Console (16), and insert batteries into the battery compartment. Make sure to orient the bat- teries as shown by the diagram inside the

battery compartment. Then, reattach the battery cover.

13

16

Battery

Cover

14. Have a second person hold the Console (16) near the Console Post (73). Connect the wires on the Console to the Main Wire Harness (45) and to the Pulse Wires (68).

Insert the excess wire into the Console Post (73) or into the Console (16).

Tip: Avoid pinching the wires. Attach the

Console (16) to the Console Post (73) with four

M4 x 16mm Screws (47).

14

16

Avoid pinching the wires

68

45

73

47

12

15. Attach the Water Bottle Holder (27) to the Front

Frame (23) with two M4 x 16mm Screws (47).

15

27

47

23

16. Identify the Right Upper Body Arm (88).

Orient an Upper Body Arm Cover (82) as shown, and slide it upward onto the Right Upper Body

Arm (88).

Attach the Right Upper Body Arm (88) to the

Right Upper Body Leg (86) with three M8 x

40mm Bolts (83) and three M8 Locknuts (10); make sure that the Locknuts are inside the hexagonal holes.

Then, slide the Upper Body Arm Cover (82) downward onto the Right Upper Body Leg (86).

Assemble the Left Upper Body Arm (89) in the same way.

16

89

82

83

Hexagonal Holes

10

88

83

10

86

13

17. Attach a Seat Handle (59) to the Right Seat

Bracket (15) with two M6 x 30mm Bolts (49), two

M6 Curved Washers (25), and two M6 Locknuts

(51); make sure that the Locknuts are in the hexagonal holes.

Attach the other Seat Handle (not shown) in the same way.

17

15

Hexagonal

Holes

51

49

25

59

18. Attach the Left and Right Seat Brackets (14, 15) to the Rear Frame (1) with two M8 x 125mm

Bolts (58), four M8 Small Washers (93), and two

M8 Locknuts (10).

18

10

93

14

15

1

93

58

19. Make sure that all parts of the hybrid trainer are properly tightened. Note: Extra parts may be included.

To protect the floor or carpet from damage, place a mat under the hybrid trainer.

14

HOW TO USE THE HYBRID TRAINER

HOW TO MOVE THE HYBRID TRAINER HOW TO ADJUST THE PEDAL POSITION

Due to the size and weight of the hybrid trainer,

moving it requires two persons. Stand in front of the hybrid trainer, hold the console post, and place one foot against one of the wheels. Pull on the console post and have a second person lift the rear stabilizer until the hybrid trainer will roll on the wheels. Carefully move the hybrid trainer to the desired location, and then lower it to the floor.

Each pedal can be adjusted to several positions. To adjust each pedal, loosen the pedal knob, move the pedal forward or backward to the desired position, and then retighten the pedal knob.

Console

Post

Knob

Place your foot here

HOW TO USE THE ELLIPTICAL MODE

To use the hybrid trainer as an elliptical, first pivot the console post to the high position and tighten the console knob and the washer into the front frame.

Lift here

Knob

Washer

15

Then, lift a pedal, fold the brace upward against the pedal, and pivot the pedal downward to the low position. Repeat this action for the other pedal.

To dismount the hybrid trainer, wait until the pedals come to a complete stop. Note: The hybrid trainer does not have a free wheel; the pedals will con-

tinue to move until the flywheel stops. When the pedals are stationary, step off the higher pedal first.

Then, step off the lower pedal.

HOW TO USE THE RECUMBENT BIKE MODE

To use the hybrid trainer as a recumbent bike, first remove the console knob and the washer, and pivot the console post to the low position.

Brace

To mount the hybrid trainer in the elliptical mode, hold the handlebars or the upper body arms and step onto the pedal that is in the lower position. Then, step onto the other pedal.

Knob

Washer

Upper Body Arms

Handlebars

Pedals

Then, lift a pedal, unfold the brace, and insert the end of the brace into the pedal carriage. Make sure that the brace is securely inserted into the pedal carriage. Repeat this action for the other pedal.

Crank Arm

Push the pedals until they begin to move with a continuous motion. Note: The crank arms can turn in either direction. It is recommended that you move the crank arms in the direction shown by the arrow; however, for variety, you can turn the crank arms in the opposite direction.

Brace Carriage

16

CONSOLE DIAGRAM HOW TO USE THE MANUAL MODE

1. Turn on the console.

To turn on the console, press the On/Reset button or begin pedaling. The entire display will turn on for a moment; the console will then be ready for use.

2. Select the manual mode.

When you turn on the console, the manual mode will be selected.

If you have selected a workout, reselect the manual mode by pressing any of the Smart Workouts Apps buttons repeatedly until zeros appear in the display.

3. Change the resistance of the pedals as desired.

As you pedal, change the resistance of the pedals by pressing the

Resistance increase and decrease buttons.

FEATURES OF THE CONSOLE Note: After you press the buttons, it will take a moment for the pedals to reach the selected resistance level.

The console offers a selection of features designed to make your workouts more effective.

4. Follow your progress with the display.

When you use the manual mode of the console, you can change the resistance of the pedals with the touch of a button. As you pedal, the console will provide continuous exercise feedback. You can even measure your heart rate using the handgrip heart rate monitor.

The console has several displays that show the following workout information:

Speed——This display shows your pedaling speed, in revolutions per minute (rpm).

The console also offers fourteen smart workouts—— seven workouts for the recumbent bike mode and seven workouts for the elliptical mode. Each workout automatically changes the resistance of the pedals and prompts you to vary your pedaling pace while guiding you through an effective workout.

Time——This display shows the elapsed time.

Note: When a workout is selected, the display shows the time remaining in the workout instead of the elapsed time.

Distance——This display shows the distance you have pedaled, in total revolutions.

Before using the console, make sure that batteries are installed (see assembly step 13 on page 12). If there is a sheet of plastic on the display, remove the plastic.

Calories——This display shows the approximate number of calories you have burned.

17

Pulse——This display shows your heart rate when you use the handgrip heart rate monitor.

Scan——When you select this display option, the upper section of the display will show both time and distance information, the lower left section of the display will show calories information, and the lower right section of the display will show your pedaling speed.

To reset the display, press the On/Reset button.

To pause the console, stop pedaling. When the console is paused, the time will flash in the display.

To continue your workout, simply resume pedaling.

5. Measure your heart rate if desired.

Note: If there are sheets of plastic on the metal contacts of the handgrip heart rate monitor, remove the plas-

tic. To measure your heart rate, hold the handgrip heart rate monitor, with your palms resting against the contacts. Avoid moving your hands or gripping the contacts tightly.

Contacts

When you turn on the console, the scan display will be selected automatically.

An indicator will appear below the word SCAN to show that the scan display is selected.

As you exercise, the upper section of the display will alternately show the elapsed time and the distance that you have pedaled; the lower left section of the display will show the number of calories you have burned. The lower right section of the display will show your pedaling speed.

Indicator

When your pulse is detected, the heart-shaped indicator in the display will flash each time your heart beats and two dashes will appear. After a moment, your heart rate will be shown in the display.

For the most accurate heart rate reading, con-

tinue to hold the contacts for about 15 seconds.

Note: If you continue to hold the handgrip heart rate monitor, the display will show your heart rate for up to 30 seconds. The display will then show your heart rate along with the other modes.

In addition, the

RPM meter on the right side of the display will provide a visual representation of your pedaling speed. As RPM Meter you increase or decrease your pedaling speed, bars will appear or disappear in the RPM meter.

If your heart rate is not shown, make sure that your hands are positioned as described. Be careful not to move your hand excessively or to squeeze the contacts tightly. For optimal performance, clean the contacts using a soft cloth; never use alcohol, abrasives, or chemicals to clean the contacts.

6. When you are finished exercising, the console will turn off automatically.

If the pedals do not move for a few seconds, the time will flash in the display and the console will pause.

To cancel the scan mode, press the Display button.

The indicator below the word SCAN will disappear.

The upper section of the display will then show only the elapsed time. If you press the Display button again, the upper section of the display will show only the distance pedaled. To select the scan mode again, press the Display button repeatedly until an indicator appears below the word SCAN.

If the pedals do not move for a few minutes, the console will turn off and the display will be reset.

18

HOW TO USE A SMART WORKOUT

1. Turn on the console.

To turn on the console, press the On/Reset button or begin pedaling. The entire display will turn on for a moment; the console will then be ready for use.

2. Select a smart workout.

When you select a Recumbent smart workout, you must adjust the hybrid trainer to the recumbent bike mode for the console to provide accurate feedback (see HOW TO USE THE RECUMBENT BIKE

MODE on page 16).

When you select an Elliptical smart workout, you must adjust the hybrid trainer to the elliptical mode for the console to provide accurate feedback

(see HOW TO USE THE ELLIPTICAL MODE on page 15).

The target speed settings for the workout will be shown by the target meter in the display. The

RPM meter will show your actual pedaling speed.

Target Meter

RPM Meter

As the target meter changes in height during the workout, adjust your pedaling speed so that the same number of bars appears in both meters. If your pedaling speed is slower than the current target speed, an arrow will appear next to the RPM meter to prompt you to increase your speed; if your pedaling speed is faster than the target speed, an arrow will prompt you to decrease your speed.

To select a smart workout, press the desired Smart

Workout Apps button repeatedly. The name of the workout will appear in the display.

A few seconds after you select a smart workout, the display will show the duration of the workout.

3. Begin pedaling to start the workout.

IMPORTANT: The target speed settings for the workout are intended only to provide a goal.

Your actual pedaling speed may be slower than the target speed settings, especially during the first few months of your exercise program.

Make sure to pedal at a speed that is comfortable for you.

The display will show the time remaining in the workout. If you stop pedaling for a few seconds, the workout will pause and the time will flash in the display. To resume the workout, simply resume pedaling.

The smart workouts consist of several one-minute segments. One resistance level and one target speed (rpm) are programmed for each segment.

Whenever the resistance is about to change, the resistance level will flash in the display for a few seconds. The resistance of the pedals will then automatically change to the resistance level programmed for the next segment.

4. Follow your progress with the display.

See step 4 on page 17.

5. Measure your heart rate if desired.

See step 5 on page 18.

6. When you are finished exercising, the console will turn off automatically.

See step 6 on page 18.

If the resistance level for the current segment is too high or too low, you can manually override the setting by pressing the Resistance buttons.

IMPORTANT: When the current segment of the workout ends, the pedals will automatically adjust to the resistance level programmed for the next segment.

19

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, try to correct the interference by one or more of the following measures:

•• Reorient or relocate the receiving antenna.

•• Increase the separation between the equipment and the receiver.

•• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•• Consult the dealer or an experienced radio/TV technician for help.

FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting to computer or peripheral devices. Changes or modifications not expressly approved by the party responsible for compliance could void the user’’s authority to operate this equipment.

20

MAINTENANCE AND TROUBLESHOOTING

Inspect and tighten all parts of the hybrid trainer regularly. Replace any worn parts immediately.

To clean the hybrid trainer, use a damp cloth and a small amount of mild soap. IMPORTANT: To avoid damage to the console, keep liquids away from the console and keep the console out of direct sunlight.

CONSOLE TROUBLESHOOTING

Most console problems are the result of low batteries.

See assembly step 13 on page 12 for replacement instructions.

If the console does not display your heart rate when you use the handgrip heart rate monitor, see step 5 on page 18.

HOW TO ADJUST THE REED SWITCH

If the console does not display correct feedback, the reed switch should be adjusted.

To adjust the reed switch, see EXPLODED DRAWING

A on page 26. Remove the M4 x 16mm Screws (47) and the M4 x 25mm Screws (41) from the Left and

Right Shields (17, 18). Make sure to note which size

of Screw you remove from each hole. Then, gently move the Right Shield out of the way.

Note: For clarity, the right shield is shown removed in the drawing below.

Next, locate the Reed Switch (43). Loosen, but do not remove, the M4 x 12mm Screw (31).

31 38

43

24

Next, rotate the Pulley (24) until a Magnet (38) is aligned with the Reed Switch (43). Slide the Reed

Switch slightly toward or away from the Magnet. Then, retighten the M4 x 12mm Screw (31).

Rotate the Pulley (24) for a moment. Repeat these actions until the console displays correct feedback.

When the reed switch is correctly adjusted, reattach the shields.

21

HOW TO ADJUST THE DRIVE BELT

If you can feel the pedals slip while you are pedaling, even when the resistance is adjusted to the highest level, the drive belt may need to be adjusted.

To adjust the drive belt, see EXPLODED DRAWING A on page 26. Remove the M4 x 16mm Screws (47) and the M4 x 25mm Screws (41) from the Left and

Right Shields (17, 18). Make sure to note which size

of Screw you remove from each hole. Then, gently move the Left Shield out of the way.

Note: For clarity, the left shield is shown removed in the drawing at the right.

Loosen the M6 x 20mm Hex Screw (46). Then, tighten the M10 x 50mm Hex Screw (66) until the Drive Belt

(35) is tight.

35

46

66

When the Drive Belt (35) is tight, tighten the M6 x

20mm Hex Screw (46). Then, reattach the shields.

22

EXERCISE GUIDELINES

WARNING:

Before beginning this or any exercise program, consult your physician. This is especially important for persons over age 35 or persons with pre-existing health problems.

The heart rate monitor is not a medical device.

Various factors may affect the accuracy of heart rate readings. The heart rate monitor is intended only as an exercise aid in determining heart rate trends in general.

These guidelines will help you to plan your exercise program. For detailed exercise information, obtain a reputable book or consult your physician. Remember, proper nutrition and adequate rest are essential for successful results.

EXERCISE INTENSITY

Whether your goal is to burn fat or to strengthen your cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your heart rate as a guide to find the proper intensity level.

The chart below shows recommended heart rates for fat burning and aerobic exercise.

To find the proper intensity level, find your age at the bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your age define your ““training zone.”” The lowest number is the heart rate for fat burning, the middle number is the heart rate for maximum fat burning, and the highest number is the heart rate for aerobic exercise.

Burning Fat——To burn fat effectively, you must exercise at a low intensity level for a sustained period of time. During the first few minutes of exercise, your body uses carbohydrate calories for energy. Only after the first few minutes of exercise does your body begin to use stored fat calories for energy. If your goal is to burn fat, adjust the intensity of your exercise until your heart rate is near the lowest number in your training zone. For maximum fat burning, exercise with your heart rate near the middle number in your training zone.

Aerobic Exercise——If your goal is to strengthen your cardiovascular system, you must perform aerobic exercise, which is activity that requires large amounts of oxygen for prolonged periods of time. For aerobic exercise, adjust the intensity of your exercise until your heart rate is near the highest number in your training zone.

WORKOUT GUIDELINES

Warming Up——Start with 5 to 10 minutes of stretching and light exercise. A warm-up increases your body temperature, heart rate, and circulation in preparation for exercise.

Training Zone Exercise——Exercise for 20 to 30 minutes with your heart rate in your training zone. (During the first few weeks of your exercise program, do not keep your heart rate in your training zone for longer than 20 minutes.) Breathe regularly and deeply as you exercise ; never hold your breath.

Cooling Down——Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles and helps to prevent post-exercise problems.

EXERCISE FREQUENCY

To maintain or improve your condition, complete three workouts each week, with at least one day of rest between workouts. After a few months of regular exercise, you may complete up to five workouts each week, if desired. Remember, the key to success is to make exercise a regular and enjoyable part of your everyday life.

23

SUGGESTED STRETCHES

The correct form for several basic stretches is shown at the right. Move slowly as you stretch; never bounce.

1. Toe Touch Stretch

Stand with your knees bent slightly and slowly bend forward from your hips. Allow your back and shoulders to relax as you reach down toward your toes as far as possible. Hold for 15 counts, then relax.

Repeat 3 times. Stretches: Hamstrings, back of knees and back.

2. Hamstring Stretch

1

Sit with one leg extended. Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg. Reach toward your toes as far as possible. Hold for 15 counts, then relax.

Repeat 3 times for each leg. Stretches: Hamstrings, lower back and groin.

3. Calf/Achilles Stretch

With one leg in front of the other, reach forward and place your hands against a wall. Keep your back leg straight and your back foot flat on the floor. Bend your front leg, lean forward and move your hips toward the wall. Hold for 15 counts, then relax. Repeat 3 times for each leg.

To cause further stretching of the achilles tendons, bend your back leg as well. Stretches: Calves, achilles tendons and ankles.

3

2

4. Quadriceps Stretch

With one hand against a wall for balance, reach back and grasp one foot with your other hand. Bring your heel as close to your buttocks as possible. Hold for 15 counts, then relax. Repeat 3 times for each leg.

Stretches: Quadriceps and hip muscles.

5. Inner Thigh Stretch

Sit with the soles of your feet together and your knees outward. Pull your feet toward your groin area as far as possible. Hold for 15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip muscles.

4

5

24

PART LIST

Model No. 831.23880.0 R0913A

Key No. Qty. Description Key No. Qty. Description

1

1

7

9

4

2

1

1

1

1

1

1

1

1

2

2

2

1

1

1

1

16

4

1

2

1

2

2

1

1

2

2

5

12

1

2

1

1

17

5

4

2

1

2

3

4

2

10

1

8

25

26

27

28

29

30

31

32

17

18

19

20

21

22

23

24

9

10

11

12

13

14

15

16

1

2

3

4

5

6

7

8

41

42

43

44

45

46

47

48

49

50

33

34

35

36

37

38

39

40

Rear Frame

Front Stabilizer

Upper Body Arm Cap

Wheel

Snap Ring

Rear Stabilizer

Seat Handle Cap

Rear Stabilizer Cap

Console Knob

M8 Locknut

Seat Frame Cap

Seat

Leg Bushing

Left Seat Bracket

Right Seat Bracket

Console

Left Shield

Right Shield

Leg Cap

Seat Frame Cap

Crank

Clamp

Front Frame

Pulley

M6 Curved Washer

Seat Handle Grip

Water Bottle Holder

Idler Screw

Front Frame Bumper

Resistance Motor

M4 x 12mm Screw

M6 Washer

M10 x 98mm Bolt

M8 x 20mm Screw

Drive Belt

M8 x 10mm Screw

Eddy Mechanism

Magnet

M10 Curved Washer

M10 x 65mm Screw

M4 x 25mm Screw

M8 Split Washer

Reed Switch/Wire

Crank Bearing

Main Wire Harness

M6 x 20mm Hex Screw

M4 x 16mm Screw

M10 Locknut

M6 x 30mm Bolt

Upper Body Arm Grip

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94

95

96

97

98

*

4

8

1

6

8

4

2

2

2

1

1

1

14

1

1

1

2

2

6

2

1

2

1

1

1

1

2

2

1

1

6

2

6

2

2

1

2

1

1

6

1

1

4

2

6

1

1

2

––

Note: Specifications are subject to change without notice. For information about ordering replacement parts, see the back cover of this manual. If a part is missing, call 1-888-533-1333. *These parts are not illustrated.

M6 Locknut

M6 x 38mm Bolt

Handlebar

M8 Large Washer

M4 x 5mm Screw

Carriage Bushing

Large Bumper

M8 x 125mm Bolt

Seat Handle

Backrest

M10 x 60mm Bolt

Idler

Pivot Bushing

Right Pedal Carriage

Left Pedal Carriage

M10 x 50mm Hex Screw

Pedal

Pulse Grip/Pulse Wire

Small Bumper

Pedal Knob

Right Pedal Leg

Crank Arm

Console Post

Left Upper Body Leg

Right Pedal Leg Bracket

Left Pedal Leg Bracket

Crank Arm Screw

Crank Arm Cap

Left Pedal Leg

Axle

Wave Washer

Upper Body Arm Cover

M8 x 40mm Bolt

Pedal Plate

Pedal Brace

Right Upper Body Leg

M10 x 102mm Bolt

Right Upper Body Arm

Left Upper Body Arm

Pivot Cover

Ground Screw

M4 x 10mm Screw

M8 Small Washer

M8 x 65mm Bolt

M8 x 13mm Screw

M10 x 25mm Screw

M10 x 54mm Screw

M10 Split Washer

User’’s Manual

25

EXPLODED DRAWING A

Model No. 831.23880.0 R0913A

26

EXPLODED DRAWING B

Model No. 831.23880.0 R0913A

27

90 DAY FULL WARRANTY

If this Sears Hybrid Trainer fails due to a defect in material or workmanship within 90 days of the date of purchase, call 1-800-4-MY-HOME® (1-800-469-4663) to arrange for free repair (or replacement if repair proves impossible). The frame is warranted for 5 years from the date of purchase.

This warranty does not apply when the Hybrid Trainer is used commercially or for rental purposes.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

Part No. 345486 R0913A Printed in China © 2013 ICON IP, Inc.