DR-MVIS

DR-MVIS
JVC
DVD VIDEO RECORDER &
VIDEO CASSETTE RECORDER
DR-MVIS
VIDEO
RAM/'RW
D[1_
DIGITAL
[DIGITALVIDEO)
DIGITAL AUDIO
VIDEO
CD
For Customer Use:
INSTRUCTIONS
Enter below the Model No. and
Serial No. which are located on
the rear of cabinet. Retain this
information for future reference.
Model No.
Serial No.
LPTO918-OO1B
2 EN
Dear Customer,
Thank you for purchasing the JVC DVD video recorder. Before
use, please read the safety information and precautions to
ensure safe use of your new unit.
CAUTIONS
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
CAUTION:
This unit should be used with AC 120V_, 60Hz only.
To prevent electric shocks and fire hazards, DO NOT use any
other power source.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
CAUTION:
A UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS
UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE
HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE
SURE TO OPERATE THE UNIT CORRECTLY AS
INSTRUCTED.
WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO
NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE
DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE
INSIDE OF THIS UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELE
REFER SERVICING TO QUALIFIED PERSONNEL.
CLASS 1 LASER PRODUCT
REPRODUCTION OF LABELS
WARNING LABEL INSIDE OF THE UNIT
ATTENTION:
POUR €:VITER LES CHOCS ELECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU
FOND.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's
attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
CAUTION:
Changes or modifications not approved by JVC could void user's
authority to operate the equipment.
EN
IMPORTANT
PRODUCT
SAFETY
INSTRUCTIONS
Electrical energy can perform many useful functions. But improper
use can result in potential electrical shock or fire hazards. This
product has been engineered and manufactured to assure your
personal safety. In order not to defeat the built-in safeguards,
observe the following basic rules for its installation, use and
servicing.
ATTENTION:
Follow and obey all warnings and instructions marked on your product
and its operating instructions. For your safety, please read all the safety
and operating instructions before you operate this product and keep
this booklet for future reference.
INSTALLATION
1. Grounding or Polarization
(A)Your product may be equipped with a polarized alternatingcurrent line plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This is a
safety feature.
If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
(B)Your product may be equipped with a 3-wire grounding-type
plug, a plug having a third (grounding) pin. This plug will only fit
into a grounding4ype power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the grounding-type plug.
ANTENNA INSTALLATION
INSTRUCTIONS
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product,
be sure the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSl/NFPA 70,
provides information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding connectors, location of
antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
2. Lightning
For added protection for this product during a lightning storm, or
when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning
and power-line surges.
3. Power Lines
An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing
an outside antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with them
might be fatal.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSl/NFPA 70
LEADIN WIRE
GROUND CLAMP
2. Power Sources
Operate your product only from the type of power source indicated
on the marking label. If you are not sure of the type of power
supply to your home, consult your product dealer or local power
company. If your product is intended to operate from battery power,
or other sources, refer to the operating instructions.
3. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
4. Power Cord Protection
Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
5.
Ventilation
Slots and openings
in the cabinet are provided
for ventilation.
To
ensure reliable operation
of the product and to protect it from
overheating,
these openings
must not be blocked or covered.
• Do not block the openings by placing the product on a bed, sofa, rug
or other similar sudace.
• Do not place the product in a built-in installation such as a bookcase
or rack unless proper ventilation is provided or the manufacturer's
instructions
have been adhered to.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
3
ELECTRIC SERVICE
_ANTENNA
DISCHARGE UNIT
NECSECTION
810-20)
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODESYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL
ELECTRICAL
CODE
4
EN
USE
SERVICING
1. Accessories
1. Servicing
If your product is not operating correctly or exhibits a marked
change in performance and you are unable to restore normal
operation by following the detailed procedure in its operating
instructions, do not attempt to service it yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
To avoid personal injury:
• Do not place this product on an unstable cart, stand, tripod, bracket,
or table. It may fall, causing serious injury to a child or adult, and
serious damage to the product.
• Use only with a cart, stand, tripod, bracket, or table recommended by
the manufacturer or sold with the product.
• Use a mounting accessory recommended by the manufacturer and
follow the manufacturer's instructions for any mounting of the product.
• Do not try to roll a cart with small casters across thresholds or deeppile carpets.
2. Product and Cart Combination
A product and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
product and cart combination to overturn.
PORTABLE
CARTWARNING
(Symbol
provided
by RETAC)
3. Water and Moisture
Do not use this product near water--for
example, near a bath tub, wash bowl,
kitchen sink or laundry tub, in a wet
basement, or near a swimming pool and
the like.
4. Object and Liquid Entry
Never push objects of any kind into this product through openings
as they may touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of any kind
on the product.
5. Attachments
Do not use attachments not recommended
this product as they may cause hazards.
by the manufacturer
6. Cleaning
Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
7. Heat
The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
of
2. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the
product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance-this indicates a need for service.
3. Replacement
Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or which have the same characteristics as the
original part. Unauthorized
shock or other hazards.
substitutions
may result in fire, electric
4. Safety Check
Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the
product is in safe operating condition.
HOW TO USE THIS INSTRUCTION
MANUAL
• All major sections and subsections are listed in the Table Of Contents
on page 7. Use this when searching for information on a specific
procedure or feature.
• The Index on pages 12 - 16 lists frequently-used terms, and the
number of the page on which they are used or explained in the
manual. This section also illustrates the controls and connections on
the front and rear panel, the front display panel and the remote
control.
• The 7. mark signals a reference to another page for instructions or
related information.
• Operation buttons necessary for the various procedures are clearly
indicated through the use of illustrations at the beginning of each
major section.
BEFORE
YOU INSTALL
YOUR
NEW UNIT...
•.. please read the sections/literature
listed below•
• "CAUTIONS" on page 2
• "IMPORTANT PRODUCT SAFETY INSTRUCTIONS" on pages 3 - 5
EN 5
Declaration of Conformity
Model Number:
DR-MV1S
Trade Name:
JVC
When the equipment is installed in a cabinet or a shelf, make sure
that it has sufficient space on all sides to allow for ventilation
(10 cm or more on both sides, on top and at the rear).
Responsible Party: JVC Americas Corp.
Address:
1700 Valley Road Wayne, N.J. 07470
Telephone Number: 973-317-5000
When discarding batteries, environmental problems must be
considered and the local rules or laws governing the disposal of
these batteries must be followed strictly.
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
Failure to heed the following precautions may result in
damage to the unit, remote control or disc/cassette.
1. DO NOT place the unit --- in an environment prone to extreme temperatures or
humidity.
-- in direct sunlight.
-- in a dusty environment.
-- in an environment where strong magnetic fields are
generated.
-- on a surface that is unstable or subject to vibration.
2. DO NOT block the unit's ventilation openings or holes.
(if the ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
3. DO NOT place heavy objects on the unit or remote control.
4. DO NOT place anything which might spill on top of the unit
or remote control.
(If water or liquid is allowed to enter this equipment, fire or
electric shock may be caused.)
5. DO NOT expose the apparatus to dripping or splashing.
6. DO NOT use this equipment in a bathroom or places with
water. Also DO NOT place any containers filled with water or
liquids (such as cosmetics or medicines, flower vases, potted
plants, cups, etc.) on top of this unit.
7. DO NOT place any naked flame sources, such as lighted
candles, on the apparatus.
8. AVOID violent shocks to the unit during transport.
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
)rotection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced
help.
radio/TV technician for
MOISTURE
VCR Plus+, C 3 and PlusCode are registered trademarks of
Gemstar Development Corporation.
The VCR Plus+ system is manufactured under license from
Gemstar Development Corporation.
TM iS an official trademark
of DIRECTV, Inc., a unit of GM
Hughes Electronics. DISH Network _Mis a trademark of Echostar
Communications Corporation.
DSS
[3D
DIGITAL
• Manufactured under licence from Dolby Laboratories. "Dolby" and
double-D symbol are trademarks of Dolby Laboratories.
• "DTS" and "DTS Digital Out" are trademarks of Digital Theater
Systems, Inc.
• This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must
be authorized by Macrovision Corporation, and is intended for home
and other limited viewing users only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or disassembly is
prohibited.
CONDENSATION
Moisture in the air will condense on the unit when you move it from
a cold place to a warm place, or under extremely humid
conditions--just
as water droplets form on the surface of a glass
filled with cold liquid. In conditions where condensation may occur,
disconnect the unit's power plug from the wall and keep it
disconnected for a few hours to let the moisture dry, then turn on
the unit.
ATTENTION:
To mobile phone users:
Using a mobile phone in the vicinity of the unit may cause picture
vibration on the TV screen or change the screen to a blue back
display.
On placing the unit:
Some TVs or other appliances generate strong magnetic fields.
Do not place such appliances on top of the unit as it may cause
picture disturbance.
6
EN
This unit allows you various types of playback and recording because this unit has two tuners.
Record
programs
on bothDVDdeckandVCRdecksimultaneously OperatetheDVDdeckwhilerecording
ontheVCRdeck
1 Start recording on the DVD deck. (7, pg. 38)
1 Start
2 Start recording on the VCR deck. (:7, pg. 50)
2 Press VCR/DVD.
NOTE:
DV IN connector is available for DVD deck only,
3 Operate the DVD deck.
Recording
recording on the VCR deck. (: _ pg. 50)
Recording
Playback, recording, etc.
Recording
Watchanotherprogram
whilerecording
ontheunit
Pressing VCR/DVD switches to the other tuner.
OperatetheVCRdeckwhiletheDVDdeckis intimerstandby
mode
2 Press VCR/DVD.
1 Engage the DVD deck's timer mode. (7, pg. 41)
• The VCR deck is automatically selected and the VCR lamp lights up
on the unit.
3 Press CH +/- to select the desired channel.
2 Operate the VCR deck.
1 Start recording on the DVD deck or VCR deck. ( " pg. 38, 50)
Playback,
recording, etc.
Timer standby mode
Recording
Another
program
OperatetheVCRdeckwhilerecording
onthe DVDdeck
1 Start recording on the DVD deck. (: :" pg. 38)
2 Press VCR/DVD.
3 Operate the VCR deck.
Playback, recording, etc.
OperatetheDVDdeckwhiletheVCRdeckis intimerstandby
mode
Pressing VCR/DVD switch to the other tuner.
1 Engage the VCR deck's timer mode. (: -" pg. 52)
• The DVD deck is automatically selected and the DVD lamp lights up
on the unit.
2 Operate the DVD deck.
Recording
Timer standby mode
Playback,
recording, etc,
CONTENTS
DISCINFORMATION
8
About Discs ...................................................................................8
INDEX
12
INSTALLING
YOURNEWUNIT
17
Basic Connection ........................................................................ 17
INITIALSETTINGS
18
Plug & Play Set ...........................................................................
18
Language ....................................................................................
19
Clock Set .....................................................................................
20
Tuner Set ....................................................................................
21
Cable Box and/or DBS Receiver Control Setting (DVD Deck
Only) ..................................................................................
22
Monitor Set (DVD Deck Only) .....................................................
24
OPERATIONSON DVD DECK
25
Basic Playback ............................................................................
Playback Features ......................................................................
Live Memory Playback ................................................................
Using The On-screen Bar ...........................................................
Parental Lock ..............................................................................
Basic Recording ..........................................................................
Recording Features .....................................................................
VCR Plus+ _ Timer Programing ....................................................
Manual Timer Programing ...........................................................
On-Disc Timer Programing .........................................................
Automatic Satellite Program Recording (DVD Deck Only) ..........
25
26
29
33
37
38
39
41
42
43
46
OPERATIONSON VCR DECK
47
Basic Playback ............................................................................
Playback Features ......................................................................
Basic Recording ..........................................................................
Recording Features .....................................................................
VCR Plus+ _ Timer Programing ....................................................
Manual Timer Programing ...........................................................
47
48
50
50
52
53
NAVIGATION (DVD DECKONLY)
55
Library Database DVD Navi ........................................................
Modify Original Information .........................................................
Modify Play List Information ........................................................
Modify Library Information ...........................................................
Playback With MP3/JPEG Navigation .........................................
55
56
58
60
61
EDITING
62
Tape Dubbing (From VCR To DVD) ...........................................
Manual Dubbing (From VCR To DVD) ........................................
Disc Dubbing (From DVD To VCR) .............................................
Manual Dubbing (From DVD To VCR) ........................................
DV Dubbing (DVD Deck Only) ....................................................
Edit From A Camcorder ..............................................................
Edit To Or From Another Recorder .............................................
Digital Audio Dubbing ..................................................................
62
63
64
65
66
67
68
69
REMOTECONTROL
70
Remote Control Functions
..........................................................
70
SYSTEM
CONNECTIONS
72
Connecting To A Dolby Digital Decoder Or An Amplifier With
Built-in DTS ...........................................................................
72
EN
7
SUBSIDIARY
SETTINGS
73
Mode Set (DVD Deck) ................................................................
Mode Set (VCR Deck) ................................................................
Changing VCR Plus+ _ Setting .....................................................
Format A Disc (DVD Deck Only) ................................................
Finalize A Disc (DVD Deck Only) ...............................................
Scan Mode Set ...........................................................................
Tray Lock (DVD Deck Only) .......................................................
73
75
77
78
79
80
80
TROUBLESHOOTING
81
GLOSSARY
86
SPECIFICATIONS
87
APPENDIX
88
LISTOFTERMS
91
WARRANTY
92
8 EN
DISC INFORMATION
i AboutDiscs
Recordable/playableDiscs
You can use discs
playback.
with
the following
Iogos
RAtv_
R A/V_4.7
for recording
and
RW
DVD-RAM
12 cm: 4.7 GB/9.4 GB
8 cm: 1.4 GB/2.8 GB
Ver. 2.0
Ver. 2.1
DVD-RW
12 cm: 4.7 GB/9.4 GB
Ver. 1.0 (VR mode)
Vet. 1.1 (Video mode/VR mode)
R
R4.7
DVD-B
12 cm: 4.7 GB
8 cm: 1.4 GB
General Ver. 2.0 (Video mode)
After finalizing -After a DVD-R/RW disc (Video mode) has been finalized, it is
possible to play back the recorded programs (video and/or audio)
on a standard DVD video player as a DVD VIDEO disc.
• Edited titles are displayed as the
"DVD menu" in video mode.
• It is impossible to record, edit or
delete the data either in video
mode or in VR mode.
• Either in video mode or in VR
mode, although the disc can be
played back on DVD players from
other manufacturers, sometimes it
may net be possible to play back
depending on the disc and recording conditions.
• It is impossible to record on CD-R/RW or DVD-R discs used for
authoring.
• It is impossible to record onto DVD-R/RW (Video mode) discs
broadcasts that allow you to copy once. The copy once programs can
only be recorded onto DVD-RW discs formatted in VR mode.
NOTE:
The following may result if you play back a DVD-R disc recorded on
another unit.
• The disc does not play.
• A mosaic pattern (block noise) appears on the screen.
• Video or audio may be dropped out.
• The unit stops during playback.
DiscsForPlayback
Only
The above table is based on the information
as of February 2004.
Recording and playback may not be performed depending on the
characteristics
and condition of the disc used, leading to
unsatisfactory
results. Using discs manufactured
by JVC is
recommended
since they have been tested to be compatible with this
unit.
You can use discs
with the following
DVD VIDEO
Iogos
for playback
only.
Video CD/Super Video CD
VIDEO
DVD-RAM
Discs
It is only possible
standard
Version
to use discs
2.0 or 2.1.
which
conform
with
DVD-RAM
• It is impossible to record on DVD-RAM discs which do not conform to
this standard. If you use a disc formatted
under a different standard
version, format it on this unit before use.
• It may not be possible to record, play back, edit or dub a DVD-RAM
disc even if it conforms to the standard if it was recorded or edited on
the devices from other manufacturers
or on a PC, or if it has far too
many titles, or if there is very little available capacity remaining on the
disc.
• Some DVD-RAM
discs are contained in a cartridge. This unit cannot
handle this type of disc. Remove the disc from the cartridge (only
discs with a removable cartridge); or the use of DVD-RAM
discs not
contained in a cartridge is recommended.
• DVD-RAM discs recorded on this unit cannot be played back on an
incompatible
DVD player.
• It is possible to record copy-once programs of digital broadcasts only
onto 4.7/9.4 GB DVD-RAM
discs (2.8 GB DVD-RAM discs are not
compatible).
DVD-R/RW
Discs
It is only possible to use DVD-R discs which conform with DVD-R
standard Version 2.0.
When a DVD-R/RW disc (Video mode) is finalized (3 pg. 79), it
can be played back on a standard DVD player as a DVD VIDEO
disc.
When a DVD-RW disc (VR mode) is finalized (3 pg. 79), it can be
played back on a standard DVD player compatible with the VR
mode of DVD-RW discs.
Before finalizing --- it is possible to record on unrecorded areas of the disc, edit the
disc title and program titles, and delete programs.
• It is impossible to record or edit DVD-R/RW discs recorded on other
devices even if they have not been finalized.
• It is impossible to overwrite recorded areas of DVD-R discs.
• Available recording capacity does not increase even if a recorded
program is deleted from a DVD-R disc.
(example
indications)
of region
@Q
code
@
CD-DA
co°
files
DIGITAL AUDIO
o_
IDIGITAL
vJoEol (SUPERVIDE
CD-DA/JPEG/
MP3 files
[Recordable}
CD-DA/JPEG/
CD-RW
MP3 files
[_oc_
_
JPEG/MP3
CD-ROM
files
[ReWritable]
• Playback may not be performed depending on the characteristics
and
condition of the disc used.
• DTS Audio CDs can also be played back (An optional DTS decoder is
required).
• MP3 and JPEG discs can be played back on this unit only when they
have been recorded in the ISO9660 or Joliet format and finalized.
• JPEG files that can be played back on this unit must conform to JFIF/
Baseline process, and the maximum
resolution of a JPEG file is
3,840 x 2,160 pixels.
• CD-R/RW discs recorded in music CD format need to be finalized to
play back on this unit.
• Operation and audio quality of this unit are not guaranteed
for discs
that do not conform to the Compact Disc specification
(CD-DA).
Before you play back a CD, check for the CD logo and read the notes
on the package to confirm that it conforms to the Compact Disc
specification.
• Depending on the intentions of the author of the software, recording
conditions of DVD discs and Video CD discs may be restricted. Since
this unit plays back discs according to the intentions of the author of
the software as indicated on the disc, some functions may not
operate as commanded.
• When switching from the first layer to the second layer of doublelayered DVD VIDEO discs, the image and sound may be momentarily
distorted. This is not a malfunction.
DISC INFORMATION
• When
switching
from
thefirstlayer
tothesecond
layer
ofdoublelayered
DVD
VIDEO
discs,
theimage
and
sound
may
bemomentarilyRecordingMediumAndFormat
distorted.
Thisisnotamalfunction.
DVD-RAM
• DVD-AUDIO
discs
compatible
withDVD
video
players
canbeplayed. • Recording and erasing can be performed
• Super
Audio
CDs
(SACD)
compatible
withconventional
CDplayers on a disc.
canbeplayed.
• Editing can be performed after recording,
UnplayableDiscs
The following types of discs cannot be played using this unit.
Do not attempt to play back any kind of disc that is damaged
(cracked, warped, or repaired with adhesive tape) or discs in
unusual shapes (heart-shaped, octagonal, or other forms). If such
discs are accidentally played back, it may cause noise that can
lead to speaker damage.
• CD-ROM discs (including PHOTO-CD and CD-G)
• Discs recorded in Packet Write (UDF) format.
• 1.3-GB double density CDs (DDCD)
• High density CDs (HDCD)
The following discs also cannot be played back.
• Discs of a region number other than "1"
• DVD-RAM (2.6 GB/5.2 GB)
• DVD-RAM (TYPE1)
EN
9
as many times as possible
such as deleting unwanted
parts.
• While recording, it is possible not only to start playback of a program
currently being recorded, but also to watch another program
previously recorded.
DVD-RW (VR mode)
• Recording and erasing can be performed as many times as possible
on a disc.
• Editing can be performed after recording, such as deleting unwanted
parts.
DVD-RW (Video mode)
• Can be played back on other DVD players.
• New recording can be performed by erasing all the data on a disc
once played back.
DVD-R
• Can be played back on other DVD players.
• Suitable when keeping a recorded disc for a long time.
FileStructureOf Discs
RegionNumber
The world is divided into 6 regions for DVD VIDEO discs.
DVD VIDEO discs are assigned a region number to indicate which
region they may be played back in. A disc cannot be played back
on this unit unless the region number of the disc matches that of
the unit. The region number for this unit is "1". Only discs whose
region number includes "1" or "ALE' can be played back such as
shown below.
DVD VIDEO
Typically, DVD VIDEO discs are made up of larger units called
"titles". Each title has a number (title number) that can be used to
select desired titles. Titles are further divided into units called
"chapters". Each chapter has a number (chapter number) that can
also be used to select desired chapters. Note that some discs are
not divided into titles and chapters.
Examples of DVD VIDEO labels which can be played back
using this unit.
When you record a program on a DVD-RAM/RW (VR mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted when
recording is paused, or audio changes from monaural to stereo
due to commercial breaks, etc. It is also possible to insert chapter
marks at desired locations during playback. (:> pg. 27)
Marks
When you record a program on a DVD-R/RW (Video mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted when
recording is paused, or audio changes due to commercial breaks,
etc. It is also possible to insert chapter marks at desired locations
during either recording or playback. Once the disc has been
finalized, these chapter marks are deleted and new chapter marks
are assigned automatically approximately every 5 minutes.
of discs in this instruction
Allows operation with a
DVD-RAM disc.
Allows operation with a
DVD-R disc.
manual
Allows operation with a
Video CD disc.
an Audio CD disc.
Allows operation with
Allows operation with a
DVD-RW disc.
Allows operation with a
disc including MP3
files.
Allows operation with a
DVD VIDEO disc.
Allows operation with a
disc including JPEG
files.
DVD-RAM.
Title 1
_l
_
Title 2
b,.I
Chapter 3 I IChap ter 1 I Chapter 2 I Chapter 3 l
• In Video mode, even before finalizing, it is impossible to perform
editing operations other than changing the disc name and/or title
names and deleting programs and/or titles.
• After finalizing, it is impossible to perform editing operations.
10 EN DISC
Audio
INFORMATION
CD/Video
CD
Typically, Audio CD discs are divided into separate tracks each
containing one song. Each track is assigned a number. For
example, the third track is Track 3. The same is true for Video CD
discs.
However, some discs are not divided into tracks.
DVDVIDEOMarks
Sometimes marks are printed on a DVD disc and/or on its
packaging to indicate information regarding the contents and
functions of the disc. Check the marks indicating the contents and
functions of the disc. Note, however, that in some cases a disc may
not include a mark even for a function it supports.
Marks
I
Audio CD4.or_Video
CD
Track2
Track3
-_-_
Track 4
m
JPEG/MP3 Disc (CD-R/RW/ROM)
MP3/JPEG files put in directories nested in several levels on a disc
will be organized as if they were put in single level directories
(groups) by the MP3/JPEG Navigation of this unit. (: ="pg. 61)
Track 1
@
File structure of a disc before starting the MP3/JPEG
Navigation
[
Root
related
to video
-_-_-
}-[_
Number of subtitles
Number of angles
Recorded under the
Screen includes black
bands at the top and
the bottom of image
which has a standard
4:3 aspect ratio (letter
box)
standard 4:3 aspect
ratio
file 1.rap3 _
Video playback is in Wide video mode (16:9) on
wide televisions, but in letter box on televisions
with standard 4:3 aspect ratio.
<_>
Directory
MP3 file
JPEG file
File structure of the disc after starting the MP3/JPEG
Navigation
Files are automatically grouped as follows and displayed on the
MP3/JPEG Navigation screen. Data is displayed in the
alphabetical order of file name. Files are grouped based on roots.
[
Root 1
Video playback is in Wide video mode (16:9) on
wide televisions, but pan and scan is used on
televisions with standard 4:3 aspect ratio (either
the left or right side of the image is cut-out).
Marks
related
@_),_
NLt_
DIGITAL
( f_le
2.rap3h
r
E.rope ]
_)
[
POPS
(file 4.mp3 )
[ Pranco
1
• This unit can recognise up to 9 hierarchies including directories and
files.
Also, it can recognise up to 250 files in each group, and up to 99
groups on a disc.
NOTES:
• Video CD discs that support Playback Control (PBC)
The contents of a disc are recorded into several hierarchies, and played
back according to the instructions on the screen while navigating through
the hierarchies. It is also possible to playback recorded tracks
consecutively without activating the PBC function even when playing a
PBC-compatible disc. ( "pg. 29)
• Regarding the contents recorded on discs
Some files may not be played back depending on the file types and other
factors.
to audio
N umber of audio trac ks
Dolby Digital mark
It has been developed by Dolby Laboratories
digital surround system.
_ _(; _T t, L
DTS (Digital Theater Systems)
sL kROUND
You
can enjoy
audio
connect
an
amplifier
with aDTS
built-in
DTSif you
decoder
to the
DIGITAL AUDIO OUT connector of the unit.
as a
DISC INFORMATION
PlacingA Disc
Opening
the disc tray
Press A (OPEN/CLOSE)
CareAndHandlingOf Discs
to open the disc tray.
• Pressing the button again closes the disc tray,
• Use the buttons to open and close the disc tray,
• Do not block the disc tray with your hand while it is opening or closing
as this may result in hardware failure.
• Do not place unplayable discs or any object other than a disc on the
disc tray,
• Do not press clown strongly on the disc tray or place any heavy
objects on it.
Discs without cartridges
Place the disc on the disc tray with the
label side facing up. Since disc size
changes depending on the disc to be
played back, be sure to correctly align
the disc with the grooves for its size. If
the disc is not in its groove, it may be
scratched or otherwise damaged. To
insert an 8 cm disc, place it according
to the inner groove.
DVD-RAM
cartridges
Double-sided
EN11
discs contained
in
discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the side
you wish to play back or record facing down. If you insert the disc
with "Side A" facing down, programs are recorded on the side A.
Single-sided
discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the label
side facing up.
How to handle discs
When handling a disc, do not
touch the surface of the disc.
Since discs are made of
plastic, they are easily
damaged. If a disc gets dirty,
dusty, scratched or warped, the
images and sound will not be
picked up correctly, and such a
disc may cause the unit to malfunction.
Label side
Do not damage the label side, stick paper to or use any adhesives
on its surface.
Recording side
Make sure that discs are not scratched and dirty on the recording
side before use. Scratches and dirt on the recording side of a disc
may hinder proper playback and recording. Also be careful that a
DVD-RAM disc may get scratched or dirt when removed from
cartridge then put back in after use.
Storage
Make sure that discs are kept in their cases. If discs are piled on
top of one another without their protective cases, they can be
damaged. Do not put discs in a location where they may be
exposed to direct sunlight, or in a place where the humidity or
temperature is high. Avoid leaving discs in your car!
Maintenance
of discs
If there are fingerprints or other dirt adhering
to a disc, wipe with a soft dry cloth, moving
from the centre outwards.
If a disc is difficult to clean, wipe with a cloth
moistened with water. Never use record
cleaners, petrol, alcohol or any anti-static
agents.
CAUTION:
Sometimes during playback, noise may appear or images may
be garbled. This is sometimes due to the disc. (It may not be up
to industry standards.)
These symptoms are caused by the discs, not by the malfunction
of the unit.
12 EN INDEX
FrontView
O Standby/On Button (d_/0
O VCR/DVD Button
O VCR Timer Lamp (TIMER) _-, pg. 52
VCR Lamp : -, pg. 47
VCR Recording Lamp (REC),
pg. 50
O Cassette Loading Slot
O Open/Close Button (A (OPEN/CLOSE)) • pg. 11
O Stop Button (11) , pg. 25, 47
O Play Button (1_) : , pg. 25, 47
O DVD Timer Lamp (TIMER) 7, pg. 41
DVD Lamp : _ pg. 19, 25
DVD Recording Lamp (REC) 7, pg. 38
O Disc Tray
_) Dubbing Button (DUBBING) : pg. 62
Dubbing Direction Button (VCR--_/*-DVD) 7, pg. 62, 64
G) Eject Button (A (VCR EJECT)) _' pg. 47
S-video Input Connectors (S-VIDEO) (DVD deck only)
::, pg. 67
_) Video/Audio Input Connectors (VIDEO/AUDIO (L/R))
, pg. 67
When using a monaural audio cable, use AUDIO L (MONO) input
connector. In this case, the sound on the left channel is also
recorded on the right channel.
_) Front Display Panel • pg. 14
_) Infrared Beam Receiving Window
_) Remain Button (REMAIN) :7, pg. 28, 39
Recording Mode Button (REC MODE) 7, pg. 38, 50
_) Record Button (0) :-, pg. 38, 50
_) Pause Button (11) :_, pg. 25, 47
_) Reverse Search Button (_1-_1) (DVD deck) • pg. 26, 32
Rewind Button (_141) (VCR deck) :=, pg. 47, 48
Reverse Slow Button (SLOW -) _7 pg. 27
_) Forward Search Button (1_1_) (DVD deck) _ pg. 26, 32
Fast Forward Button (1_1_) (VCR deck) : -, pg. 47, 48
Forward Slow Button (SLOW +) : 7-pg. 27
_) Channel Button (CH +/-) >, pg. 38, 50
_1 Automatic Satellite Program Recording Button (REC
LINK) (DVD deck only) : -, pg. 46
_) DV Input connector (DV IN (F,*))(DVD deck only)
_ pg. 66
* _,(i.Link) refers to the IEEE1394-1995 industry specification and
extensions thereof, The _, logo is used for products compliant with the
i.Link standard.
To access covered connectors, pall
and open the connector cover.
INDEX
EN13
RearView
Ii
,oE
1
l=
d
O Region Number Label : •pg. 9
OACPowerCord
•pg. 17
O Cooling Fan
• This prevents the temperature
from rising inside the unit.
Do not remove it.
• Install the unit so as not to block the area around the fan.
• The cooling fan on the rear of the unit may be activated even if
the unit is turned off in the following cases;
-- in the Automatic Satellite Program Recording standby mode
(_ _ pg. 46)
-- when "AUTO
CLOCK"
is set to "ON" (
"pg. 20)
O Digital Audio Output Connectors
(DIGITAL AUDIO OUT (COAXIAL/OPTICAL))
(DVD
deck only) : • pg. 69, 72
O Component Video Output Connectors (COMPONENT
VIDEO OUT) (DVD deck only) : -, pg. 17
O S-videoNideo/Audio
Output Connectors (S-VIDEO/
VIDEO/AUDIO OUTPUT) (DVD deck only) • pg. 17, 68
O S-video Input Connector (S-VIDEO INPUT) (DVD deck
only) >, pg. 68
O Antenna Input Connectors (VHF/UHF IN (DVDNCR))
:7, pg. 17
O Video/Audio Input Connectors (VIDEO/AUDIO INPUT
(L-l)) •pg.
68
_) Video/Audio Output Connectors (VIDEO/AUDIO
OUTPUT)
pg. 17, 68
• Cable Box Control Connector (CABLE BOX) (DVD deck
only)
pg. 22
_1 Antenna Output Connectors (VHF/UHF OUT (ANT.
LOOR OUT/TV OUT)) 7, pg. 17
14 ENINDEX
FrontDisplayPanel
• _www_
_www_
0 Disc Type Indicator
When a disc is loaded,
the disc marks rotate.
Rotate faster than normal playback.
Rotate slower than normal playback.
Inner red ring lights in the same way
as normal playback. During Instant
Timer Recording (ITR), inner red ring
slowly blinks.
Disc marks blink when either
recording or playing back.
Disc marks all light.
Disc marks all blink.
During High-Speed Search:
During Slow Motion:
While recording:
While
paused:
_wwww=
=www®=
=www®=
_w®ww=
_w®ww=
_ww®w_
_ww®w_
_) Repeat Mode Indicator (_L3/1/A-B) ::_ pg. 34, 49
the type of the disc is indicated.
Disc Status Indicator
When a disc is running,
_wwww=
While stopped:
While resume stopped:
While the disc tray opened:
No disc on the disc tray:
Disc marks all light out.
Disc marks all light out.
O VR Mode Indicator >. pg. 78
Lights when a DVD-RW disc is formatted in VR mode.
O _
Indicator •pg.
43
Lights when a disc set up for On-Disc Timer Programing is loaded.
O Recording
Mode Indicator (XP/SP/LP/EP/FR)
:7. pg. 38
Blinks when recording mode is being set.
While "FR" is blinking, the left 3 digits of the Multi Display (@_})
indicate setting values ranging from "60" to "480". After the value
has been set, only "FR" lights.
O Group/Title
Indicator (GRP/TITLE)
"GRP" or "TITLE" lights depending on a disc loaded while the left 2
digits of the Multi Display (_)) indicate the numbers explained below.
"GRP":
Total number of groups or group number being played
back are displayed on the Multi Display.
"TITLE": Total number of titles or title number being played back
are displayed on the Multi Display.
O Track/Chapter
Indicator (TRK/CHAP)
"TRK" or "CHAP" lights depending on a disc loaded while the 3rd
and 4th digits from the left of the Multi Display (_)) indicate the
numbers explained below.
"TRK":
Total number of tracks or track number being played
back are displayed on the Multi Display.
"CHAP":
Chapter number being played back are displayed on the
Multi Display.
O Simulated
Surround
Effect Indicator (3D) _. pg. 35
Lights when a simulated surround effect is set to "3D-ON" on the onscreen bar.
O Linear PCM Indicator (LPCM)
Lights when "XP MODE REC AUDIO" is set to "LINEAR PCM"
(
pg. 74) for recording with DVD-RAM, DVD-R and DVD-RW
discs, and when Linear PCM audio is played.
O Random/Program
Playback Mode Indicator (RND/
PRGM) __ pg. 36
"RND":
Lights when Random Playback mode is set.
"PRGM": Lights when Program Playback mode is set.
Select Repeat Playback mode on the on-screen
bar.
"(_=_":
Whole disc is played back repeatedly.
It also lights up during the Repeat Playback
VCR deck.
"_
1":
"_..._A-B":
No display:
on the
A single title/chapter/track
is played back repeatedly.
The selected part (A-B) is played back repeatedly.
Repeat Playback mode is off.
_) Automatic Satellite Program Recording Indicator
7,pg. 46
Lights up when the DVD deck is in the Auto Satteliite Program
Recording standby mode while the VCR deck is used.
_1 VCR Indicator
_ pg. 39, 50
Lights up when the mode is switched to the VCR mode using the
TV/VCR button. When switching the mode, "VCR" or "TV" appears
for about 2 seconds on the Multi Display ((i_).
_) Video Output Indicator (_) :_, pg. 80
No display:Indicates
that interlace mode is engaged.
_:
Indicates that progressive mode is engaged.
(Example)
_ lights when video output mode is in progressive
mode.
_) Group/Title Number Display
_) Track/Chapter Number Display
_) Remaining Time/Elapsed Time Indicator _, pg. 28, 39
Lights when remaining time of DVD-RAM, DVD-R and DVD-RW
discs is displayed, and lights out when elapsed time is displayed.
The right 6 digits of the Multi Display (_)) indicate elapsed or
remaining time of each track.
No display:Indicates
elapsed time of the disc.
Displayed: Indicates remaining time of the disc.
_1 Remaining Time/Elapsed
Multi Display
Time Display __,pg. 28, 39
Displays clock, received channel, elapsed time, and remaining
Also displays status of the unit (NO DISC/OPEN/CLOSE/
READING).
time.
INDEX
EN
15
On-ScreenDisplay(DVD deck)
When "SUPERIMPOSE"
is set to "AUTO" and ON SCREEN
oil the remote
TV screen. To clear the operational
indicators,
press ON SCREEN
twice.
O Disc Display
Displays
Displays
number
of the title currently
being played
playback
operation
status
playback
•
time of the title currently
operational
indicators
appear
playback
point and other
information
on the
in bar meter.
Displays title name newly registered to the title recorded
RAM/RW/R
discs, or file name of JPEG and MP3 files.
by pictographs.
O Playback Time*
Displays
various
1_)Title Name Display
back.
O Playback Operation Status Indicator*
Indicates
is pressed,
O Clock Display
O Bar Meter Display :, pg. 31
the type of the disc leaded on the disc tray.
O Title Number*
Displays
control
being played
back.
Operation Status Indicator
Indicates operation status by pictographs.
(Also indicates its speed
for forward high-speed
search, reverse high-speed
search and slow
motion.)
O Recording Mode
Displays recording mode as XP, SP, LP, EP, FR, FR60-FR360,
FR420 and FR480. Current recording mode is displayed during
recording, and recording mode in which the program was recorded
is displayed during playback. The recording mode is not displayed
during play list playback.
O Title Number
on DVD-
Time Display
Displays single title playback elapsed time, single track playback
elapsed time, single track remaining time, total elapsed time, total
remaining time, and other information
in turn.
@) Audio Mode Display
Displays playback title number
number during recording.
during
playback,
and recording
title
O Chapter Number
Displays playback chapter number
chapter number during recording.
Displays
audio that is being input.
_) Channel Position Number/Auxiliary
or F-l)
during
playback,
and recording
Displays
currently
selected
Input Indicator (L-1
input.
* During Live Memory playback, playback operation status is displayed.
During normal playback, the multichannel encoding method is displayed.
On-ScreenDisplay(VCRdeck)
When "SUPERIMPOSE"
is set to "AUTO" and ON SCREEN
oil the remote
TV screen. To clear the operational
indicators,
press ON SCREEN
again.
control
is pressed,
various
operational
indicators
appear
on the
0 Operation Mode Indicators
O Recording Mode (SP/EP)
0 Tape Position Indicator
@___
-OR 125
SUN 12:00 AM
STEREO
SAP
C ........
_ORM
tJ:II-FI
I1-+--REMAIN
COUNT
The tape position indicator
appears on the TV screen when
you press 4_1 or _
from the
Stop mode or perform an Index
Search. (_ 7 pg. 48) The position
of '11"in relation to "0" (Beginning)
or "+" (End) shows you where
you are on the tape.
REC0RRq
PAUSEJ
sP.
.......
E
ff_DEX
1O : 0
-1 : 23 : 45
NOTE:
Depending on the type of tape
being used, the tape position
indicator may not appear
correctly.
O
O
O
O
0
0
_)
•
-B........
Beginning
=............
E
COUNT 0 : 33:27
End
Index number _, pg. 48
Tape Remaining Time Indicator __ pg. 51
Counter Display
Audio Mode Display,
pg. 49
SAP Indicator _, pg. 51
Stereo Program Indicator,
pg. 51
Day/Clock Display
Channel Position Number/Auxiliary Input Indicator (L-1
or F-l)
"Cassette Loaded" Mark
16 ENINDEX
RemoteControl
_)
_)
_)
_)
_)
_)
_)
_)
_1
@
I_)
I_)
_)
_)
_)
_)
_)
_)
The glow-in-the-dark buttons shown in grey on the illustration
above are helpful when using the remote control in darkened
rooms.
Buttons
used
to operate
with a small
yourdot
TV.on
(:7,
the
pg.left
70)side of the name can also be
0 DVD Timer Button (DVD TIMER (®)) (DVD deck only)
_, pg. 41
O VCR Timer Button (VCR TIMER (®)) (VCR deck only)
:, pg. 52
0 Number Keys _, pg. 21, 38, 50
Character keys (DVD deck only) _7 pg. 57
O Auxiliary Button (AUX)
0 Cancel Button (CANCEL) _, pg. 41
O Program Check Button (PROG/CHECK) 7, pg. 42, 45,
53, 54,
0 VCR Plus+ Button _ pg. 41,52
0 Top Menu Button (TOP MENU) (DVD deck only)
pg. 26
Navigation Button (NAVIGATION) (DVD deck only)
, pg. 55
O /\_ Button
pg. 19
_) Set Up Button (SET UP) (DVD deck only) :-, pg. 19
• Reverse Skip Button (14141)(DVD deck) _7 pg. 26, 32
Index Button (1_1_1)(VCR deck) _7 pg. 48
Previous Button (PREVIOUS) (DVD deck only) 7, pg. 29
_)
_)
_)
_)
_)
Play Button (1_) >, pg. 25, 47
Select Button (SELECT) (DVD deck only) >, pg. 25, 56
Reverse Search Button (_14) (DVD deck) y, pg. 26, 32
Rewind Button (_141) (VCR deck) >, pg. 47, 48
Reverse Slow Button (SLOW -) • pg. 27
Stop Button (11)7, pg. 25, 47
Clear Button (CLEAR) (DVD deck only) _-, pg. 35, 41
Record Button (@) _• pg. 38, 50
Remain Button (REMAIN) 7, pg. 28, 39
Recording Mode Button (REC MODE) : 7 pg. 38, 50
Subtitle Button (SUBTITLE) (DVD deck only) 7 pg. 28
Angle Button (ANGLE) (DVD deck only) :-, pg. 28
Live Check Button (LIVE CHECK) (DVD deck only)
7,pg. 30, 32
TVNCR Button :=, pg. 39, 50
Audio Button (AUDIO) : 7 pg. 28, 49
TV Muting Button (_) • pg. 70
TV/CABLE/DBS/DVD switch 7, pg. 19
VCR/DVD Button _7 pg. 19
TV/CBL/DBS/DVD Standby/On Button (cb/I)
Memo Button (MEMO) (DVD deck only) 7, pg. 56, 59, 61
Mark Button (MARK) (DVD deck only) :=, pg. 27
On-Screen Button (ON SCREEN) (DVD deck only)
7, pg. 15, 33
Progressive Scan Button (PROGRESSIVE SCAN)
, pg. 80
Display Button (DISPLAY) _7 pg. 28, 39
Menu Button (MENU) (DVD deck only) y, pg. 26
< _ Button :7 pg. 19
Enter Button (ENTER) _, pg. 19
Return Button (RETURN) : • pg. 29, 41
Forward Skip Button (l_l_l) (DVD deck)
pg. 26, 32
Index Button (1_1_1)(VCR deck) :7, pg. 48
Next Button (NEXT) (DVD deck only) • pg. 29
Forward Search Button (1_1_) (DVD deck) >, pg. 26, 32
Fast Forward Button (1_1_) (VCR deck) : -, pg. 47, 48
Forward Slow Button (SLOW +) • pg. 27
Pause Button (11) _, pg. 25, 47
Skip Search Button (_)
• pg. 27, 32
One Touch Replay Button (_)
7- pg. 32, 48
TV Volume Button (TV VOL.) : 7 pg. 70
TV/CBL DVD Channel Button (CH +/-) • pg. 38, 70
How To Use
Before use, insert two AA size batteries into the remote control
with the polarity (0 and Q) matched correctly as indicated on
the battery compartment or on the lid.
The remote control can operate most of your unit's functions, as
well as basic functions of TV sets of JVC and other brands.
( " pg. 70)
• Point the remote control toward the receiving window.
• The maximum operating distance of the remote control is about
8m.
NOTE:
If the remote control doesn't work properly, remove its batteries,
a short time, replace the batteries and then try again.
wait
INSTALLING
•
| BasicConnection
Flat feeder
Matching transformer
(not supplied)
RF cable (supplied)
Antenna splitter
t
AV Connection
• S-Video Connection (DVD deck only)
To connect to TV'e S-VIDEO input and AUDIO input
connectors
[] Perform
-2 in "RF Connection".
[] Connect the unit's S-VIDEO OUTPUT connector to the TV's
S-VIDEO input connector.
[] Connect the unit's AUDIO OUTPUT connectors to the TV's
AUDIO input connectors.
• You can obtain high-quality S-VHS pictures.
• If your TV is not stereo-capable, use the unit's AUDIO OUTPUT
connectors to connect to an audio amplifier for Hi-Fi stereo sound
reproduction.
Coaxial cable
AC outlet
EN17
To connect to a TV with AV input connectors -[] Perform
-_ in "RF Connection".
[] Connect an optional audio/video cable between the AUDIO/
VIDEO OUTPUT connectors on the rear panel of the unit and the
TV's audio/video input connectors.
Antenna or Cable
t
YOUR NEW UNIT
(supplied)
• Component Video Connection (DVD deck only)
To connect to TV'e component video input connectors
[] Perform-_
in "RF Connection".
[] Connect the unit's COMPONENT VIDEO OUT connectors to
the TV's component video input connectors.
[] Connect the unit's AUDIO OUTPUT connectors to the TV's
AUDIO input connectors.
• You can obtain high-quality component video pictures.
• If your TV is not stereo-capable, use the unit's AUDIO OUTPUT
connectors to connect to an audio amplifier for Hi-Fi stereo sound
reproduction.
• By using the component video connection, you can view the images
in the progressive mode. For switching to the progressive mode, refer
to "Scan Mode Set" (__ pg. 80).
RF cable (supplied)
VHF/UHF
IN (DVD/VCR)
/
Back of unit
S-VIDEO
_
4 Plug the end of the AC power cord into an AC outlet. This unit
performs Plug & Play Set automatically. (7- pg. 18)
• The clock and tuner channels will automatically be set when the
antenna is connected and when the AC power cord is first connected
to an AC outlet. (If "AUTO" and the channel indicator are displayed on
the front display panel before the unit is powered on, the clock and
tuner channels are being set automatically. Wait for the time to be
displayed on the front display panel before turning on the unit.)
• "LOADING" blinks on the front display panel when the AC plug of the
power cord is connected into a mains outlet and it takes
approximately 50 seconds for the unit to be turned on. This is not a
malfunction.
OUTPUT
S-Video cable
(not supplied)
Component
video cable
(not supplied)
T°7°hml
terminal
5 Set the video channel. The video channel is the channel on
which you can watch the picture from the unit on the TV when only
using RF connection.
(not supplied)
It's essential that your unit be properly connected.
OPERATION
BE PERFORMED.
THESE STEPSCAN
MUST
BE COMPLETED
BEFORE ANY VIDEO
1 Make sure the package contains all of the accessories
"SPECIFICATIONS"
on page 87.
listed in
2 Place the unit on a stable, horizontal surface.
3 Connect the unit to a TV depending
on the TV and cables you
With RF Connection
Set the video channel to "3 CH" or "4 CH". To set the video
channel, perform steps _] - [g below:
• The video channel is preset to "3 CH". Set to "4 CH" if the Channel 3
is used for broadcasting in your area.
With AV Connection
Set the video channel to "- CH" (off). To set the video channel,
perform steps
-[_ below:
With S-Video/Component
Video Connection (DVD deck only)
Set the video channel to "- CH" (off). To set the video channel,
perform steps
-[_ below:
use.
•
RF Connection
To connect to a TV with NO AV input connectors -[] Disconnect the TV antenna from the TV.
[] Connect the TV antenna cable to the VHF/UHF IN (DVD/VCR)
connectors on the rear panel of the unit via antenna splitter.
[] Connect an optional RF cable between the TV OUT connector
on the rear panel of the unit and the TV's antenna terminal.
NOTES:
• If you do not use antenna splitter, connect the TV antenna cable to
VHF/UHF IN (DVD) connector. However, it is not possible to record
the TV program on the VCR deck.
• Connect the unit's ANT. LOOP OUT connector to the antenna input
connector on another vide unit.
How To Set The Video Channel
[] Make sure that there is no cassette in the unit.
[] Press d)/[ to turn off the unit, then press • on the unit for more
than 5 seconds. "3 CH" appears on the front display panel.
[] Press OH +/- on the remote control to select "3 CH", "4 CH" or
"- CH" (off), then press ENTER. When either "3 CH" or "4 CH" is
selected, the TVNCR indicator lights up.
18 ENINITIAL
SETTINGS
I Plug& Play Set
Auto ClockSet/Auto TunerSet
This unit sets the clock and tuner channels automatically when AC
power cord is first connected to an AC outlet. The antenna cable
must be connected for the Plug & Play setting.
The time and date can be set automatically by the clock setting
data transmitted from one of the regular TV broadcast channels.
We call this TV channel the "host channel" and it is a PBS channel
in your area.
ATTENTION:
• If you use a cable box, Plug&Play will not function; set the clock
and tuner channels separately. (z" pg. 20 - 21 )
• Depending on areas or reception conditions, the unit may not
receive the Auto clock setting data from the PBS channel. If this
function is taking a considerable
amount of time, it may be
necessary to perform the Semiauto or Manual Clock Set
procedure.
1
Connect
the antenna
cable
to the unit. (..:y" pg. 17) Then
connect
the AC power cord to an AC outlet. Do not turn on the unit.
The clock and tuner channels
will be set automatically.
• "LOADING" blinks on the front display panel when the AC plug of the
power cord is connected
into a mains outlet and it takes
approximately
50 seconds for the unit to be turned on. This is not a
malfunction.
NOTES:
• Auto Clock Set is performed first
"AUTO" blinks on the front display panel during Auto Clock Set.
• Auto Channel Set is performed next. Auto Channel Set scans all the
channels that are receivable by your unit. During Auto Channel Set,
the channel numbers are displayed as they are scanned and set.
• When Plug & Play setting has been complete successfully,
the
correct clock time is displayed. If you perform Plug & Play setting
successfully, there is no need to perform "Clock Set" (7- pg. 20) and
"Tuner Set" ( "pg. 21). If, however, you want to add or delete
channels, refer to "Manual Channel Set" (_" pg. 21 ).
During Auto Clock Set
"AUTO" blinks.
.p
During Auto Channel
The channel numbers
are scanned
and set.
Set
are displayed
and "AUTO"
blinks
as they
INFORMATION
• If "AUTO CLOCK" is set to "ON" (: :" pg. 20), the clock will be
adjusted automatically
by the host channel every hour (except
11:00 PM, midnight, 1:00 AM and 2:00 AM) using the incoming
PBS channel clock setting data. (This automatic clock adjustment
can only be performed when the unit is turned off. The clock will be
adjusted just on these hours -- on the time displayed on the front
display panel, not on the actual real time.) The default setting of
"AUTO CLOCK" is "ON". (_ - pg. 20)
• If the memory backup fails, because a power outage occurs or
because the AC power cord is unplugged,
Plug & Play will be
performed when power is restored to the unit.
What
to do if Plug & Play setting
failed
• It an Jncorrect tirne Jsdisplayed on the front display panel, you rnay
be receiving the clock setting data of a PBS channel from an
adjacent time zone, or an incorrect PBS channel from a cable TV
system. In this case, perform "Semiauto
Clock Set" ( "pg. 20) or
"Manual Clock Set" (: -" pg. 20).
• If "- -:- -" appears on the front display panel, your antenna cable
may not be connected
to the unit or there may not be a Host PBS
signal available in your area. Ensure that the antenna cable is
connected correctly. Then turn on and off the unit; the Plug & Play
setting will be automatically
reactivated.
If Plug & Play setting is not
performed though the antenna cable is connected correctly,
perform "Manual Clock Set" (: -" pg. 20) and "Auto Channel Set"
(_ - pg. 21) or "Manual Channel Set" (_ _ pg. 21).
;'f _J:
U
i LJ
PlugIPlay
Completed
The current time is displayed.
• If an incorrect clock time or "- -:- -" appears on the front display
panel, see "What to do if Plug & Play setting failed" (2" pg. 18).
I
i,J' LI Li w am
I
INITIAL
SETTING5
EN19
On-screenLanguageSet
ILanguage
This unit offers you the choice to view on-screen messages in 3
different languages.
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TVlCABLEIDBSlDVD switch to DVD.
1 Press VOR/DVD
the unit.
repeatedly so that the DVD lamp lights up on
2 Press SET UP to access the Main Menu screen.
3 Press _ b> to select "FUNCTION
4 Press 4 b. to select "DISPLAY
VCR/DVD--
SET UP", then press ENTER.
SET", then press ENTER.
GTf} d_f"J_f_J
C_D C_P c_7_
CTD
C_1
CT'D
;C_TJ
C_
C--b
5 Press/\V
to select "ON
SCREEN LANGUAGE", then
press ENTER.
--
[N'fER.......
SElUP--
[}
6 Press/\V
to select your
desired language, then press
ENTER.
7 Press SET UP to complete the setting.
Menu/Audio/SubtitleLanguageSet (DVD deckonly)
Jvc
Some DVD discs contain the DVD menu display, audio and
subtitles in multiple languages. With these discs, you can set the
default language as you like.
• The procedure shows how to set "MENU LANGUAGE" as an
example.
1 Press VCR/DVD
the unit.
repeatedly so that the DVD lamp lights up on
2 Press SET UP to access the Main Menu screen.
3 Press _ b. to select "DVD SET UP", then press ENTER.
4
Press _ b. to select
"LANGUAGE
ENTER.
SET", then press
5 Press zf\V to select "MENU
LANGUAGE", then press ENTER.
6 Press/\V
to select your
desired language, then press
ENTER.
• See "Language Code List"
(_" pg. 88).
7 Press SET UP to complete the setting.
NOTE:
When the selected language is not available on the disc, the disc's
default menu language is played back.
SETTINGS
20 EN INITIAL
laockSet
Perform clock setting only if the clock has not been set correctly by
the Plug&Play setting.
• Turn on the unit,
NOTE:
If an incorrect tirne is displayed by tile Plug & Play function, you rnay be
receiving the clock setting data of a PBS channel from an adjacent time
zone or from an incorrect PBS channel from a cable TV system. If you
selected "AUTO" for the host channel in step 6, be sure to select the
correct time zone manually.
9 Press SET UP to complete the setting.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TV/CABLE/DBS/DVD
switch to DVD.
VCR/DVD-C_7
C_7
C_
i c__J
dl_J
c_J
--
ENTER
=,_
$EfUP-tT!__
,;;:1
[;
ri_:?
IMPORTANT:
Turn off the unit after performing Semiauto Clock. "AUTO" will appear
on the front display panel while the clock is being set. The current
clock time will appear automatically when the clock setting is
complete.
Auto Daylight Saving Time
This function enables automatic adjustment of the unit's clock at
the start and end of Daylight Saving Time.
With Auto DST activated, --- on the first Sunday of April at 2:00 AM, the clock is adjusted
to 3:00 AM.
-- on the last Sunday of October at 2:00 AM, the clock is
adjusted to 1:00 AM.
NOTE:
Timer recording rnay not function correctly at tile time Daylight
Saving Time is adjusted.
ManualClockSet
SemiautoClockSet
You call change the host channel/D.S.T. (Daylight Saving Time)/
time zone setting manually,
NOTE:
Tile time set previously will be erased when "AUTO CLOCK", "HOST
CH", "D.S.T." or "TIME ZONE" setting is changed.
1 Press VCR/DVD
the unit.
repeatedly so that the DVD lamp lights up on
2 Press SET UP to access the Main Menu screen.
3 Press _ b. to select "INITIAL SET UP", then press ENTER.
4 Press 4 b. to select "CLOCK
SET", then press ENTER.
1 Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press _ b>to select "INITIAL SET UP", then press ENTER.
4
Press _ b. to select "CLOCK
SET", then press ENTER.
5 Press/\V
to select "AUTO
CLOCK", then press ENTER.
Press/\V
to select "ON", then
press ENTER.
6 Press/\V
to select "HOST
CH", then press ENTER.
Press/\V
to select "AUTO" or the
desired PBS channel number, then press ENTER.
NOTE:
Some PBS channels do not transmit clock setting data.
7
Press/\V
to select "D.S.T.", then press ENTER. Press/\V
to
select the desired setting, then press ENTER.
AUTO: Select if you want to adjust your unit's clock automatically by
the incoming signal from the host channel. Be sure to select the
correct time zone manually in step 8.
ON: Adjustment will be made by the built-in clock itself.
OFF: Select when Daylight Saving Time does not apply to you.
8 Press Z\V to select "TIME ZONE", then press ENTER. Press
Z\V to select "AUTO" or the desired time zone, then press ENTER.
• Each time you press/\'J, the time zone changes as follows:
-,--AUTO
-'-,ATLANTIC-'-,EASTER
N-'-, CENTRAL-'-,
M0UNTAIN-'-, PACIFIC-'-,ALASKA-'-,HAWAII-'-,
(backto the beginning)
5 Press/\V
to select "AUTO
CLOCK", then press ENTER.
Press/\V
to select "OFF", then
press ENTER.
6 Press/\V
to select 'q'IME",
then press ENTER. Press/\V
until the desired time appears,
then press ENTER to start clock.
• Set the date and year in the same
way.
• Holding/\'J
changes the time in 30-minute intervals, or changes the
date in 15-day intervals.
7 Press/\V
to select "D.S.T.', then press ENTER. Press/\V
to
select the desired setting, then press ENTER.
ON: Adjustment will be made by the built-in clock itself.
OFF: Select when Daylight Saving Time does not apply to you.
8 Press SET UP to complete the setting.
INITIAL
SETTINGS
EN
21
ManualChannel
Set
| TunerSet
You can add the channels you want or delete the channels you do
not want manually.
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TVlCABLEIDBSlDVD switch to DVD.
1 Press VCR/DVD
the unit.
repeatedly so that the DVD lamp lights up on
2 Press SET UP to access the Main Menu screen.
3 Press _ P>to select "INITIAL SET UP", then press ENTER.
4 Press _ b, to select "TUNER
VC£/DVD--
SET", then press ENTER.
C_D
C_P c_7_
CT_3
C_l
C_D
;C_TJ
d_
C--D
[NfER.......
SETUP--
INFORMATION
The unit selects the correct band (TV or CATV) automatically
during Auto Channel Set. The selected band will be displayed on
the right side of "BAND" on the Tuner Set screen.
Auto ChannelSet
Perform Auto Channel Set only if channels have not been set
correctly by the Plug&Play setting.
1 Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press _ b. to select "INITIAL SET UP", then press ENTER.
4
Press _ b. to select "TUNER
SET", then press ENTER.
5 Press/\V
to select "AUTO CH
SET", then press ENTER. You can
_
_
automatically set the receivable
channels in your area in the order
of their frequencies.
• When Auto Channel Set is
complete, "SCAN COMPLETED"
appears on the TV screen.
• If the scan was unsuccessful,
"SCAN COMPLETED-NO SIGNAL-" appears on screen. Check the
connections and start again.
6
Press SET UP to complete the setting.
5 Press/\V
to select "MANUAL
CH SET", then press ENTER.
6 Add or skip the desired
channels.
To add channels
[] Press/\V
to select "CH", then
press ENTER.
[] Press/\V
to select a channel
number you want to add, then press
ENTER.
[] Press/\V
to select "ADD/SKIP", then press ENTER.
[] Press/\V
to select "ADD", then press ENTER.
[] Repeat [] - [] to add other channels.
To skip channels
[] Press/\V
to select "CH", then press ENTER.
[] Press/\V
to select a channel number you want to skip, then
press ENTER.
[] Press/\V
to select "ADD/SKIP", then press ENTER.
[] Press/\V
to select "SKIP", then press ENTER.
[] Repeat [] - [] to skip other channels.
7 Press SET UP to complete the setting.
22 EN INITIAL
SETTINGS
I Cable
Boxand/or DBS
Receiver
Control
Setting(DVDDeck
Only)
The following procedure is required
if you receive
your
TV
channels through a cable box (descrambler) and/or if you receive
satellite channels through DBS (Direct Broadcast Satellite)
receiver. The Controller allows the unit to automatically switch the
cable box or DBS receiver's channel during timer recording.
NOTES:
• The Controller is not supplied with this unit. It can be requested by
mailing in the completed JVC Cable Mouse Certificate that is
included with the accessory package.
• The Controller is effective for "VCR Plus+_Timer Programing"
(_ . pg. 41), "Manual Timer Programing" (_ -" pg. 42), or "On-Disc
Timer Programing" (_ • pg. 43).
• When connecting your cable box, refer to its instruction manual.
If your cable box or DBS receiver does not have audio/video
output connectors
Connect the RF output connector on the cable box or DBS receiver
to the VHF/UHF IN (DVD) connector on the rear of your unit via
antenna splitter.
If your cable box or DBS receiver has audio/video
connectors
output
Connect the audio/video output connectors on the cable box or
DBS receiver to the AUDIO/VIDEO INPUT connectors on the rear
of the unit.
• If both a cable box and a DBS receiver are used, it is recommended
that you connect the DBS receiver to your unit's AUDIO/VIDEO
INPUT connectors and the cable box to your unit's VHF/UHF IN
(DVD) connector via antenna splitter.
4 Connect the Controller to the CABLE BOX connector on the rear
panel.
VCR/DVD--
InstallingController
1 If both a cable box and a DBS receiver are used, position the
Controller so its signal reaches the receiving windows of both the
cable box and DBS receiver.
2 Fix securely using the adhesive strip attached on the back of the
Controller.
--
ENTER
-SEfUP...........
Cable box or DBS receiver
[:
SettingBrandAndChannel
Your unit
After installation, set the cable box or DBS receiver's brand and
channel correctly; otherwise, the Controller cannot work correctly.
Controller
(suggested
locations)
• Turn on the unit.
• Turn on the TV and select the video channel (orAV mode).
• Slide the TV/CABLE/DBS/DVD switch to DVD,
3 Connect the controller to the unit.
I
Cable box or DBS receiver
To Audio/video
To RF output
output
Transmitter
1 Turn
on the cable box or DBS receiver.
2 Press VCR/DVD
the unit.
repeatedly so that the DVD lamp lights up on
3 Press SET UP to access the Main Menu screen.
4 Press _ b. to select "INITIAL SET UP", then press ENTER.
5 Press 4 b. to select "STB SET", then press ENTER.
6 Press/\V
to select "CABLE
BOX SET" or "DBS RECEIVER
or
To VHF/UHF IN
(DVD)
SET", then press ENTER.
To AUDIO/
VIDEO INPUT
_v
Your unit
7 Press/\_7 to select "CABLE
BOX OUTPUT CH" or "DBS
RECEIVER OUTPUT CH", then
press ENTER.
i TUNE_SE_
U ST_S_I_
XN_rTXAL5ETTXNG5
8
Select
the output
•
channel.
Your selection
depends
on how the cable box or DBS receiver
is
connected
to your unit.
• If the cable box or DBS receiver is connected to your unit's VHF/
UHF IN (DVD) connector on the rear panel, press/\'J
te select the
channel number representing
the cable box's output (CH2 - CH9),
then press ENTER.
• If the cable box or DBS receiver
is connected
to your unit's
AUDIO/VIDEO
Input connectors
on the front panel, press/',',J
to
select "F-I", then press ENTER.
• If the cable box or DBS receiver
is connected
to your unit's
AUDIO/VIDEO
INPUT connectors
on the rear panel, press/','J
to
select "L-I", then press ENTER.
• If you do not use a cable box or DBS receiver, press/',',J
to select
"OFF", then press ENTER.
9
Enter
1 0
the cable
Press/\V
RECEIVER
brand
BRAND",
code from
1 1 Press
box's
to select
z'\V
brand.
"CABLE
then
press
the following
to select
"TEST
BOX
BRAND"
ENTER.
list, then
press
MODE",
or "DBS
Press/\V
then
to select
ENTER.
press
ENTER.
CABLE BOX BRAND
CODE
ARCHER
CABLETENNA
CABLEVlEW
CITIZEN
CURTIS
DIAMOND
GC BRAND
GEMINI
GENERAL INSTRUMENTS
HAMLIN
JASCO
JERROLD
NOVAVlSION
OAK
PANASONIC
PULSER
RCA
REGAL
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
SPRUCER
STARGATE
TELEVlEW
TOCOM
UNIKA
UNIVERSAL
VIDEOWAY
ZENITH
1,5,17
1,17
15, 16, 17, 21, 25
15, 16, 17, 21, 25
2,8
1,17
15, 16, 17, 21, 25
15
1,4, 6, 11, 12, 15, 28
10, 18, 23
15
1,4,6,11,12,15,28
2,8
7, 20
13, 14
15, 16, 17, 21, 25
13, 14
10, 18, 23
1,16,17
5, 16,24
2,8
7, 20
5,16,17,24,25
13, 14
5, 15, 16, 17, 21, 24, 25
5, 16,24
1,4,16
1,17
16, 17, 25
3,9,22
3,9,22
DBS RECEIVER
CODE
BRAND
JVC (DISH Network)
ECHOSTAR (DISH Network)
SONY (DSS)
RCA (DSS)
51
51
41
40
the
EN23
For cable box
If the cable box's channel changes to 9, setting is complete.
Press ENTER and "CABLE BOX
CONTROL IS ON" appears on the
screen for about 5 seconds, then
the screen in step 6 appears.
If the cable box'e channel does
_,,
,_..... _
not change to 9;
[] Press _ b, to select "NO", then
press ENTER.
[] Repeat step 10 - 11 until the cable bex's channel changes to 9
by entering another code.
[] If the channel does not change after going through all the code
numbers listed for your model of cable box, then try all the other
numbers.
• For DBS receiver
If the DBS receiver's channel
changes to the channel listed
below for your brand, setting is
complete.
Press ENTER and "DBS
RECEIVER CONTROL IS ON"
appears on the screen for about 5
seconds, then press ENTER. The
screen in step 6 appears.
JVC
--*
100
SONY
ECHOSTAR
--*
100
RCA
--*
-*
If the DBS receiver's
channel
does not change
above;
[] Press _ P* to select "NO", then press ENTER.
[] Repeat step 10 - 11.
205
205
as shown
NOTES:
• The Controller may not work with all types of cable box or DBS
receiver.
• If your cable box does not respond to any code between 1 and 28,
you cannot use the Controller to change cable box channels.
In this
case, make sure to leave the cable box turned on and tuned to the
proper channel before the scheduled
start time of timer recording.
Contact your cable company about the possibility of exchanging
your
current cable box with the one compatible with your unit.
• If your DBS receiver does not respond to the code, you cannot use
the Controller to change satellite channels. In this case, make sure to
leave the DBS receiver turned on and tuned to the proper channel
before the scheduled
start time of timer recording.
• The unit can only change the cable box or satellite channel through
the Controller during timer recording.
• If your cable box or DBS receiver cannot be operated with a remote
control (because it has no receiving window), you cannot use the
Controller to change its channels. Make sure to leave the cable box
or DBS receiver turned on and tuned to the proper channel before the
scheduled start time of timer recording.
• If the unit's memory backup expires because of a power failure, set
the cable box or DBS receiver output channel and brand again.
• For customers
in U.S.A.: If you are unable to set the Controller,
contact JVC toll free at 1-800-252-5722.
24 ENINITIAL
SETTINGS
I MonitorSet(DVDDeckOnly)
You can select the monitor type depending on the TV used when
you play back DVD VIDEO discs recorded for wide-screen TVs.
1 Press VCR/DVD
the unit.
repeatedly so that the DVD lamp lights up on
2 Press SET UP to access the Main Menu screen.
3 Press _ b, to select "FUNCTION
SET UP", then press ENTER.
4 Press _ _ to select "VIDEO IN/
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TV/CABLE/DBS/DVD
switch to DVD.
OUT", then press ENTER.
5 Press/\V
to select "MONITOR
TYPE", then press ENTER.
6 Press/\V
to select the desired
Sf-
--, :
option, then press ENTER.
-_
VCR/DVD-_7
C_7
7 Press SET UP to complete the
setting.
C_
* The boldface settings below indicate the settings at your
purchase.
--
ENTER
=,_
$ETUP-tT!__
ri_:?
[;:
• MONITORTYPE-- 4:3LB/ 4:3PS/ 16:9AUTO/ 16:9 FIX
4:3LB (Letter Box conversion): Select this when the aspect ratio of
your TV is 4:3 (conventional TV). While viewing a wide screen
picture, the black bars appear on the top and the bottom of the
screen.
4:3PS(Pan&Scan):
Select this when the aspect ratio of your TV is
4:3 (conventional TV). While viewing a wide screen picture, the
black bars do not appear; however, the left and right edges of the
pictures will not be shown on the screen.
16:9 AUTO (Wide television conversion): Select this when the
aspect ratio of your TV is 16:9 (wide TV).
16:9 FIX (Wide television conversion): Select this when the aspect
ratio of your TV is fixed to 16:9 (wide TV). The unit automatically
adjusts the screen width of the output signal correctly when
playing back a picture whose aspect ratio is 4:3.
Pan&Scan/Letter
Box
In general, DVD VIDEO disc are produced for a wide-screen TV
with 16:9 aspect ratio.
Material with this ratio will not fit to a TV with 4:3 aspect ratio.
There are two styles to display the image, "Pan&Scan" (PS) and
"Letter Box" (LB).
Pan&Scan
The right and left side of the image are cut off.
The image fills the screen.
• The picture will be shown in the "4:3LB" mode
depending on the disc even if the "4:3PS" mode
is selected,
Letter Box
Black bands appear at the top and bottom of
the image. The image itself appears in 16:9
aspect ratio.
OPERATIONSON DVD DECK EN25
To play back an MP3/JPEG
Navigation"
(:y" pg. 61 ).
JJBasicPlayback
1 Load
disc, see "Playback
2 Press
the unit.
VCR/DVD
repeatedly
VCR/DVD--
so that the DVD lamp
4 Press II to pause playback.
• To resume normal playback, press
iC_3C_J
C_J
}C_J
C_3
C_3
DVD disc is
lights up on
3 Press I_ to start playback.
• If you load a DVD disc whose region code does not match the unit,
"REGION CODE ERROR" appears on the TV screen. For details,
refer to "Region Number" (y pg. 9).
• If "CAN NOT PLAY BACK DISC UNDER CURRENT
SETTING"
appears on the TV screen, refer to "Parental Lock" (:y" pg. 37).
• With Video CD discs with PBC control or some DVD discs, the menu
display may appear on the TV screen after starting playback. In this
case, select an item which you want to play back from the menu.
Otherwise, the playback cannot go forward. Refer to "Playback
Control (PBC) Function" (y" pg. 29) or "Locating A Desired Scene
Using The DVD Menu" (:" pg. 26).
• The Library Database DVD Navi also enables you to search and
select the desired programs. (:_" pg. 56)
||
V(R/DVD
MP3/JPEG
a disc.
• For details, refer to "Placing A Disc" (y" pg. 11 ).
• Pressing I_ also closes the disc tray.
• Playback begins automatically
if an auto-playback
loaded.
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TV/CABLE/DBS/DVD
switch to DVD.
With
I_.
5 Press • to stop playback.
• When a recordable disc is played, playback stops and a program
received with the unit's tuner resumes on the TV screen.
• When a playback-only
disc is played, playback stops and the still
image at the time you press • remains on the TV screen. Pressing
again resumes a program received with the unit's tuner.
• If _. (OPEN/CLOSE)
is pressed during playback, playback stops,
then the disc tray opens.
ENTER_
SELECT
m_
NOTE:
When the Library Database DVD Navi screen appears, choose a
thumbnail
image of the desired program on the TV screen, then press
SELECT(I=,-) or ENTER. (:" pg. 56)
ATTENTION:
• It takes approximately
30 seconds to read a disc depending on the
type and condition of tile disc since this unit is multi-disc
compatible (DVD-RAM,
DVD-RW, DVD-R), It may even take
several minutes when a disc is dirty_ scratched or warped,
• It may take a few seconds to start playback. This is not a
malfunction.
• Forward/reverse
high-speed
search and other operations
be performed while playback is stopped.
cannot
•
26 EN OPERATIONS
ON DVD DECK
LocatingTheStart PointOf TheItem Or SkipTheItem
| Playback
Features
•
•
•
•
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TVlCABLEIDBSlDVD switch to DVD.
Press VCR/DVD repeatedly so that the DVD lamp lights up on the
unit.
Press 14_1 or I),-I_1during playback.
• Pressing I)-I_1locates the start point of the item or skips the item for
forward direction, then resumes playback.
• Pressing I<_1 locates the start point of the item or skips the item for
reverse direction, then resumes playback.
When a DVD-RAM/RW/R
disc is played
Current program
-,,,,,,,
0=9
--MARK
TOPMENU .......
-- MENU
News
ENTER-{44
Movie
.........
SLOW-I-_-_}
-_r
m--
j
Reverse _
o,= SLOW+
(_}
.........
88
_
e: marked
I_)H _
Example:
To locate the beginning of the next item, press I_1_1once.
To locate the beginning of the current item, press 141< once.
To locate the beginning of the previous item, press 1<_1 three
times.
Jvc
When a DVD VIDEO, Audio CD or Video
LocatingA DesiredSceneUsingTheDVDMenu
;S•'i_?® i
Forward
points (3" pg. 27)
®
CD disc is played
Playback point
®
DVD VIDEO discs may have top menu and disc menu.
Top menu
DVD discs generally have their own menus which show the disc
contents. These menus contain various items such as titles of a
movie, names of songs, or artist information. You can locate a
desired scene by using the top menu displayed on the TV screen.
Press TOP MENU to access the top menu.
Disc menu
Reverse _
Disc menus include playback data (angle menu, subtitle menu,
etc.) specific to each title.
Press MENU to access the disc menu.
1
Press TOP MENU or MENU to
access the DVD menu.
2 Press/\V
Scene 2
(Chapter2)
or
Track 2
_ _ to select a
desired title, then press ENTER.
Playback starts.
• It may be possible to select the
desired
item using
keys
depending
onthe
thenumber
menu
display.
Example:
NOTE:
When "Q" appears on the TV screen
in step 1, the disc does not have a top menu or disc menu.
Scene 3
(Chapter3)
or
Track 3
I,I1<1
I_1_1_
Scene 4
(Chapter4)
or
Track 4
Forward
Example:
To locate the beginning of the next item, press I_1_1once.
To locate the beginning of the current item, press 141_1once.
High-SpeedSearch
i_ _I¸¸_
During playback, press 1_1_ for forward high-speed search, or _1_1
for reverse high-speed search.
• Each press of the button increases the search speed for each
direction.
• To resume normal playback, press I_.
OR
During playback, press and hold I_1_1for 2 or more seconds for
forward high-speed search, or press and hold 141_1for 2 or more
seconds for reverse high-speed search.
• Releasing the button resumes normal playback.
OPERATIONSON DVD DECK EN27
NOTES:
Still Picture/Frame-By-Frame
Playback
1 Press
II to pause
2
II or 4 b> to activate
Press
during
playback.
frame-by-frame
playback.
• Each press of n advances the still picture frame by frame.
• Each press of
I:, advances/reverses
the still picture frame by
frame.
• Frame-by-frame
playback for reverse direction cannot be performed
with Video CD discs.
• To resume normal playback, press I_.
SlowMotion
1 Press
II to pause
during
• Resume
playback.
2 Press SLOW - (_141) or SLOW + (1_1_).
• Each press of SLOW - (41_1) or SLOW + (1_)
increases the slow
motion speed for each direction (from 1/16 to 1/2 times the normal
speed).
• Slow motion for reverse direction cannot be performed with Video CD
discs.
OR
Press
SLOW
- (44)
or SLOW
• "DISC RESUME" setting works on DVD VIDEO, VCD and already
finalised DVD-R/DVD-RW
(video mode) discs. For other types of
discs, the function under "ON" setting will be applied even if
"RESUME"
is set to "DISC RESUME". (:" pg. 74)
• If you stop the playback of a disc for which an resume point has
already been memorized,
the memory will be updated with the new
resume point.
• After the unit has memorized the resume point for 30 discs,
remembering
a new resume point will cause the unit to delete the
oldest memorized
point. Stopping playback of a disc for which a
resume point is already stored may change the order in which the
points are stored. This may potentially change the order in which
points are deleted.
• When the unit memorizes
a resume point for a disc, it also
remembers
audio language, subtitle and angle settings.
• This function may not work for some Video CD.
• When "RESUME"
is changed to "ON" or "OFF" (: -" pg. 74), resume
points of the discs memorized
with "RESUME"
set to "DISC
RESUME" will be cleared.
+ (1_1_) for 2 or more
seconds.
SkipSearch
points are memorized
for each side of a double-sided
MarkingPositionsToPlay BackAgainLater
It is possible to mark positions
(up to 999 points) where you want to
play back once again later, and start playback
from a marked
position.
Marking onto DVD-RAM/RW/R
discs when recording
is
helpful to locate a start point when you play back the discs later.
To mark positions:
During playback,
press
MARK
at
During playback,
press f'_.
• Each press initiates an approximately
30-second
period of fastmotion playback. Normal playback resumes automatically.
positions
you want to mark.
• "MARK" appears on the TV screen.
You can easily locate the marked
positions using I<_l or 1_I_1 when you
play back the disc.
ResumeFunction
To delete the
While paused,
It is possible to memorize
the position
where you stop playback
and resume playback
from that position.
• Be sure to set "RESUME"
to "ON" or "DISC RESUME".
(_ pg. 74)
1 Press • during playback
to memories
a resume point.
• The unit enters Resume Stop mode and memorises the position
where you have stopped playback as a resume point. (The inside of
the disc status indicator on the front display panel blinks while
memorising.)
• The unit retains a memory of the resume points of the last 30 discs
played back, even though they have been ejected if "RESUME"
is set
to "DISC RESUME". (y" pg. 74)
• To clear the resume points:
(The inside of the disc status indicator stops blinking and lights.)
When "RESUME"
is set to "ON":
• Press LUl
i to turn off the unit.
• Press A. (OPEN/CLOSE)
to take out the disc.
• Press • in stop mode.
• Press TOP MENU to display the top menu, then start playback by
selecting an item, etc.
• Press MENU to display the disc menu, then start playback by selecting
an item, etc.
When "RESUME"
is set to "DISC RESUME":
• Set "RESUME" to "OFF". (:2" pg. 74)
• Press • in stop mode.
• Press TOP MENU to display the top menu, then start playback by
selecting an item, etc.
• Press MENU to display the disc menu, then start playback by selecting
an item, etc.
2
Press
playback
I_ in stop mode
from
the resume
to resume
point.
playback.
The unit starts
disc.
MARK
marked positions:
press I<<
or IH_I to
locate a marked position you want to
delete, then press MARK.
• Crossed "MARK" appears on the TV
screen, and the marked position is
deleted.
_-fr.A4Lk_l_
NOTES:
• When a monaural program changes to a stereo program while
recording, a mark signal is automatically
recorded.
• When a DVD-R/RW
(Video mode) disc is finalized, marked points
marked before finalizing will be deleted, and programs will be divided
automatically
into "chapters" approximately
every 5 minutes.
(_ _" pg. 79)
28 EN OPERATIONS
ON DVD DECK
• To clear the angle selection display, press ENTER. In addition, the
angle selection display disappears
automatically
if no operation is
done for 10 seconds.
._
CTj
C_J
-0=9
,_DISPLAY
.......MENU
TOPMENU .......
[ENTER
,-
-- RETURN
-- NEXTI_I)
PREVIOUS
({4_).........
[]
REMAIN
SubtitleSelection
--_5
C_O
-,_F
j
c_
C_l c_
_j
---SUR?ITLE
ANGLE.........
AUDIO.........
dvc
Some DVD VIDEO discs contain more than one subtitle language,
from among which you can choose the desired subtitle language.
"(_" appears on the TV screen at the beginning of the part where
more than one subtitle language are recorded.
1 Press SUBTITLE during
playback. The subtitle selection
display appears on the TV screen.
• Each time you press SUBTITLE,
the subtitle display is switched on
and off.
When 3 subtitle
contained.
languages
are
2 Press 4 b. to select your desired language.
• To clear the subtitle selection display, press ENTER.
CheckingTheTimeInformation
You can check time information of a disc on the front display panel
and the TV screen.
Press DISPLAY once to display the lastly displayed information. To
changes the display, press DISPLAY repeatedly.
• DVD-RAM/DVD-R/DVD-RW
During playback or recording
Clock time (trent display panel only) -* Current title elapsed time
--* Disc remaining time* --* (back to the beginning)
* only discs before finalizing
e Clock time is displayed only when a recordable disc is played back.
In stop mode
e It is possible to check disc remaining time according to recording
modes also by pressing REMAIN.
e In FR mode, it is possible to set recording time in detail. While the
recording mode and the disc remaining time are displayed by
pressing REMAIN, press/_'/to
select "FR", then press < 12.to
select the desired recording time. (_ • pg. 40)
e It is not possible to switch the recording mode during playback or
while recording.
•
Video CD/Audio
CD
During playback or in stop mode
Total remaining time -* Current track elapsed time -* Current track
remaining time --* Total elapsed time --_ (back to the beginning)
NOTE:
When a PBC-cornpatible Video CD disc is loaded, deactivate the PBC
function. (-" pg. 29)
AngleSelection
I•¸_'
E_
ii_ _
You can enjoy a variety of scene angles if a DVD VIDEO disc
contains "multi-angle" parts, where the same scene was shot from
different angles.
If the disc contains "multi-angle" parts, "_:_" appears on the TV
screen at the beginning of the "multi-angle" part.
1 Press ANGLE during playback.
The angle selection display
appears on the TV screen.
2 Press ANGLE or _ L>to select
When 3 scene angles are
contained,
your desired angle.
• Each time you press ANGLE or
z_:I_.,the angle changes.
• When "Q" appears on the TV screen, the current scene is not
recorded from multiple angles. In addition, some discs prohibit angle
selection.
NOTES:
• When "Q" appears on the TV screen, no subtitle language is
recorded.
• When the subtitle language won't be changed with the procedure
above, change the subtitle on a disc menu displayed by pressing
MENU.
AudioLanguage/Sound
Selection
Some DID VIDEO discs contain the multiple audio language or
sound. You can select the desired audio language or sound. For
some Video CD discs, you can switch the audio channel to choose
Karaoke either with or without the vocal.
1 Press AUDIO during playback.
The Audio Language/Sound
selection display appears.
2 Press AUDIO or _ b> to select
When 3 audio languages are
contained.
your desired audio language/
sound.
• Each time you press AUDIO or
I:,, the audio language/sound
changes.
• To clear the Audio Language/Sound selection display, press ENTER.
NOTES:
• When "_" appears on the TV screen, no audio language is recorded.
• When the audio language won't be changed with the procedure
above, change the audio on a disc menu displayed by pressing
MENU.
• It is only possible to select the audio language in stop mode. The
audio language cannot be selected during playback.
OPERATIONS ON DVD DECK
AudioChannelSelection
EN29
It is called "Live Memory Playback" to start playback of the program
being recorded, with a time-lag between a recording point and a
playback point, as shown in the figure below.
When playing discs on which you recorded stereo programs, you
can choose the desired audio channel.
• When "SUPERIMPOSE" is set to "AUTO", you can confirm on the TV
screen the audio channel you have chosen. (: . pg. 74)
• Each time you press AUDIO, the audio channel
changes.
TRACK
Current playback point
(Live Memory Playback)
Current recording position
(Recording point)
Recording start point
!
!
_y_
_ Playback
continues
go rain.
0
•]
|_
1 hour
Recording
continues
USE
On-Screen Display
I,
Currently elapsed recording time
,J
For stereo discs
O))4 L,-R_q;
0))4
L
0))4
%
Not only can this unit play back a program previously recorded
while recording or timer recording another program, but the unit
also allows you to play back from the beginning of a program while
continuing to record the same program.
For audio of left channel
For audio of right channel
PlaybackControl(PBC)Function
Recording/playback
StatusDisplay
Some Video CD discs support the PBC function. PBC is an
abbreviation of "Play Back Control". A Video CD disc recorded with
PBC has its own menus, such as a list of the songs on the disc.
You can locate a specific scene by using the menu.
1 Press I_ in stop mode. The PBC menu appears.
CTj C_'3 C_3
C_73 d-_f]C___3
CI) C_EJ C=)
--
Press the number keys to enter the number of the desired
scene. The unit starts playback of the selected item.
• "PBC" appears on the front display panel.
• When "NEXT" or "PREVIOUS" appears on the TV screen:
Pressing NEXT (l_l_l) advances to the next page.
Pressing PREVIOUS (1_1_1)returns to the previous page.
• You can return to the menu by pressing RETURN.
• The method of the operation is different depending on the disc.
NOTES:
• If you want to playback a PBC-compatible Video CD disc without
activating the PBC function, start playback in stop mode by using the
number keys, instead of the I_ button, to choose the track, then
press ENTER.
• To activate the PBC function when a PBC-compatible Video CD disc
is being played back without the PBC function, press TOP MENU, or
press • then press I_.
DISPLAY
Live Memory Playback status can be checked by
pressing DISPLAY to display the bar meter on the
superimpose display.
<_
[_;]
[°;:]
[;;]
i
Press DISPLAY. The current status is superimposed
screen.
Bar meter display
| LiveMemoryPlayback
This unit records pictures onto DVD-RAM discs, instead of video
tapes, then plays back the pictures recorded on the discs. This
makes it possible to achieve high-speed writing and read-out that
has not been possible with conventional VCRs, enabling recording
and playback simultaneously.
High-speed
Recording
(High-speed
writing)
_
spin
Playback
(High-speed
Image figure of DVD-RAM disc
read-out)
Superimpose
display
on the TV
30 EN OPERATIONS
ON DVD DECK
Overview Of LiveMemoryPlayback
You can play back a program
you are recording
called "Live Memory
Playback".
(Recording
from
the beginning
while
continuing
screen)
to record
or timer
record
(Live Memory Playback
onto a DVD-RAM
disc.
This is
screen)
To start Live Memory Playback,
press I_ to play back from the
beginning
OR press _
to
reverse-skip a litt!e
To stop Live Memory Playback,
press•
Checking the
picture currently
being recorded
To clear, press LIV E
To stop recording,
press •
(Playback
Tostop
stops
To display, press L!VE
CHECK
and Live Check screen)
Live Memory Playback,
press•
Live Memory Playback
picture
Recording
picture
NOTES:
C_O CIZJ C_D
iC_TJC_ C_
--ON $(REEN
NAVIGATION
Press NAVIGATION to display
Library Database DVD Navi menu,
then choose a program to play back.
(y" pg. 55)
O
LIVIECHECK
Pressing LIVE CHECK during Live
Memory Playback allows you to
check the picture currently being
recorded.
--c;'-
JVC
• Live Memory Playback cannot be performed for approximately
30
seconds after recording has started.
• Although high-speed search up to approximately
30 seconds before
the current recording point is possible during Live Memory Playback,
once the current recording point is reached, the unit resumes normal
playback and maintains a delay of approximately
30 seconds so that
recording and playback can continue.
• When using Live Memory Playback during timer recording, playback
continues even after the end of the recording.
• When using Live Memory Playback during timer recording, playback
is automatically
stopped just before recording starts, and then
recording starts when the time arrives for the next timer-program.
• It is impossible to perform ITR even if you press • during Live
Memory Playback.(
"pg. 39)
Press • to display the program being recorded, then perform ITR
settings.
• Playback may be paused for a moment during Live Memory
Playback, which does not interfere with recording.
• Live Memory Playback cannot be performed while recording the
source from DV input.
• When LIVE CHECK is pressed to display the picture currently being
recorded, the picture size may not be correct.
OPERATIONSON DVD DECK EN31
DisplayDuringLiveMemory Playback
During recording,
normal playback
TV screen.
you can watch at your will what was previously
operations
(forward/reverse
high-speed
search
When Live Memory
operations,
the unit
Playback
reaches the point of 30 seconds
returns to normal playback.
recorded
or is currently
being recorded.
It is possible to perform
freely
and variable-speed
search) within the range of the red or blue bar on the
before
the current
recording
point
by forward
high-speed
search
The superimpose display appears by pressing ON SCREEN. (_7 pg. 15)
The Live Check picture is displayed on the bottom right corner by pressing LIVE CHECK.
Playback counter
Recording
Live Memory Playback mark
mode
Recording title number
Playback title number
Recording counter display
(remaining/elapsed
time)
Disc used
--
Present time
Recording channel
Playback mark
Title name
Bar meter (see below)
Recording
mark
Live Check picture
Recording
This unit displays the current recording/playback
(Example of bar meter display)
mark
status by the bar meter.
Capacity of a disc
While stopped
Total length of the program being played back
Current
During playback
Capacity of a disc
Remaining
capacity when recording started
Current recordinc
While recording
Capacity of a disc
Current playback position
Recording start position
Live Memory Playback
Capacity of a disc
Recording start position
Current playback position
Current recording position
Live Memory Playback of
another program
Total length of the program being played back
Blue
_Orange
(recorded
part)
(recording part)
Green (playing part)
or other
32 EN
OPERATIONS
ON DVD DECK
ButtonsToBe UsedDuringLiveMemoryPlayback
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TVlCABLEIDBSIDVD switch to DVD.
0 II
Pressing once pauses playback (still picture playback). Pressing
repeatedly advances the still picture frame by frame.
Pressing once skips back for approximately
7 seconds and
resumes playback.
Pressing repeatedly
skips back continuously
as many times as
pressed.
It is useful when watching sports programs, etc.
C_CJ C_J cZ_CJ
icS4C] C_sm_JC%CJ
er'_
i CTb
(TY
(Ty
i C--'J
CT3
C--_
Pressing once skips forward for approximately 30 seconds and
resumes playback.
Pressing repeatedly skips forward continuously as many times as
pressed.
It is useful when skipping over unwanted sections.
--
(]) LIVE
@--
_r
_ _ ......
Jvc
O NAVIGATION
Displays Library Database DVD Navi menu. You can choose a
program to play back.
Available only when paused
Advances/reverses the still picture frame by frame.
CHECK
Pressing once displays the picture currently being recorded and
the one being played back simultaneously.
Pressing successively clears the Live Check window and displays
only the picture currently being played back.
You can check, for example, if the program you are recording has
already finished.
ToPlay BackFromTheBeginningOf TheProgram
While Recording
You can play back a program you are recording from the beginning
while continuing to record or timer record onto a DVD-RAM disc.
Press It,-. Live Memory Playback starts from the beginning of the
program being recorded.
• Pressing I<_1 or 1_I_1allows you to locate the desired scenes.
0 I<<
• Pressing once skips back to the beginning of the chapter being
played back.
• Pressing down for 2 or more seconds during playback reverses
playback at 5 times the normal speed while pressed. Releasing the
button resumes normal playback.
Available only when paused
• Pressing down for 2 or more seconds reverses playback at 1/16 times
the normal speed.
0 _1
• Pressing once skips forward to the beginning of the next chapter
being played back.
• Pressing down for 2 or more seconds during playback advances
playback at 5 times the normal speed while pressed. Releasing the
button resumes normal playback.
Available only when paused
• Pressing down for 2 or more seconds advances playback at 1/16
times the normal speed.
ToMove BackThePlaybackPositionSlightlyWhile
Recording(One TouchReplay function)
You can move back the playback position while continuing
record or timer record onto a DVD-RAM disc.
to
Press _.
• Each press skips back for approximately 7 seconds and resumes
playback.
• Pressing while paused skips back for approximately 7 seconds and
resumes pause.
ToWatchA ProgramPreviouslyRecordedWhile
Recording
You can play back a program you reeorded previously while
recording.
1 Press I_ during recording. Live Memory Playback starts.
• Each press of the button during playback advances the playback
speed in 5 steps for reverse direction.
Available only when paused
• Pressing once reverses playback by 1/16 times the normal speed.
• Each press of the button during reverse 1/16 times slow-motion
reverses slow-motion by 1/16 times, 1/4 times and 1/2 times the
normal speed.
O )')"
• Each press of the button during playback advances the playback
speed in 4 steps for forward direction.
Available only when paused
• Pressing once advances playback by 1/16 times the normal speed.
• Each press of the button during forward 1/16 times slow-motion
advances slow-motion by 1/16 times, 1/4 times and 1/2 times the
normal speed.
O,,
Stops Live Memory Playback to return to the screen being
recorded.
Then a resume point is stored.
Pressing • again stops recording.
2 Press 141_1or I_1_1to locate the beginning of the desired
program.
NOTE:
To stop playback, press m. The program being recorded is displayed.
OPERATIONS ON DVD DECK
| UsingThe0n-screenBar
The on-screen bar allows you to control various playback
functions. Some of the functions operated on Navigation Menu can
be controlled on the On-screen bar.
NAVIGATION.
Be sure to clear Library Database DVD Navi screen by pressing
[]
[]
[]
[]
[]
[]
Disc type.
Select this
Select this
Select this
Select this
Select this
[]
[]
[]
[]
[]
(_- pg. 35)
Select this for Picture Control function. (_ _"pg. 35)
Select this to switch picture source type. (_ _"pg. 36)
Current status area for the selected item.
Select this for Program Playback. (__"pg. 36)
Select this for Random Playback. (:" pg. 36)
[]
C_b L_b
r_C_¢D C_eD d2#D
CZ_
for Repeat Playback. (2" pg. 34)
for A-B Repeat Playback. (: , pg. 34)
for search function. (7. pg. 34)
for time search function. (: _"pg. 35)
to switch Simulated Surround Effect function.
Select this to control the switching interval of the slide show.
(y"pg. 36)
NOTE:
Although examples of the on-screen bar are provided here only for 3
types of discs, the on-screen bar will be displayed for whichever disc
indicated in the left column.
¢_b
l CZ_ C_ZJ C_D
C_
E. 33
C_3
--OH SCRE[N
BasicOperationOn The0n-screenBar
Example: When selecting Picture Control function of DVD
During playback or while stopped
1 Press ON SCREEN twice to access the on-screen bar. The item
_r _
currently selected is highlighted and pointed by _.
DVD:VJDEO
CD
JVC
2
Press 4 L'>to select "_",
then press ENTER. The pop-up
window appears under the selected item.
How ToAccessThe0n-screenBar
1 Press ON SCREEN whenever a disc is loaded.
Contents
of the on-screen
bar during
playback
DVD VIDEO
3 Press/\_7
Video
To clear the on-screen
Press ON SCREEN.
CD
JPEG disc
to select the desired option, then press ENTER.
bar
NOTE:
See the corresponding pages for details on each menu item.
34 EN OPERATIONS
ON DVD DECK
A-B RepeatPlayback
You can repeat the desired part.
(AN(EL--
ENTER
--
During playback
] Press ON SCREEN twice to access the on-screen bar.
2 Press _ b. to select "A_B (_".
3 Press ENTER at the beginning of the desired part you want to
repeat (point A). The elapsed playing time of the point A appears
(LIAR(E} --
DVD-RAk_
4 Press ENTER at the end of the desired part you want to repeat
(point B). The elapsed playing time of the point B appears.
• The selected part of the disc (between point A and B) is played
repeatedly.
RepeatPlayback
DVD-RAM
You can repeat playback as you like according to the type of disc.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press 4 b. to select "_",
then press ENTER. The pop-up
window appears under the selected item.
To clear the on-screen
Press ON SCREEN.
bar
To cancel A-B Repeat Playback
Press _ L> to select "A_B_",
then
press
ENTER.
NOTES:
3 Press/\V
repeatedly to select the desired Repeat mode, then
press ENTER.
DVD-RAM/RW/R
OFF:Repeat playback is not performed.
ALL REPEAT: The whole disc is played back repeatedly.
TITLE REPEAT: The current title is played back repeatedly.
DVD VIDEO
OFF:Repeat playback is not performed.
TITLE REPEAT: The current title is played back repeatedly.
CHAPTER REPEAT: The current chapter is played back repeatedly.
Audio CD/Video CD/JPEG/MP3
OFF: Repeat playback is not performed.
whole disc is played back repeatedly.
TRACK REPEAT*: The current track is played back repeatedly.
* "TRACK REPEAT"cannot be selected for JPEG discs.
• A-B Repeat Playback may not work properly depending on the type
of disc being used.
• The subtitles recorded around the A-B point may not appear.
• When the end of the item is reached before the end point is set, the
on-screen bar disappears from the TV screen. In such a case, repeat
the procedure from step 1.
• The point B must be set at least 3 seconds after the point A.
• When playing back a DVD, A-B Repeat Playback is possible only
within the same title.
• "A_E}O"
cannot be selected during Program and Random
Playback.
• "A-B _"
cannot be selected while stopped.
LocatingTheBeginningOf A DesiredSelection
ALL REPEAT:
The
To clear the on-screen
Press ON SCREEN.
bar
To cancel Repeat Playback
Repeat the above procedure from step 1, select "OFF" in step 3,
then press ENTER.
NOTES:
• Repeat Playback is not possible for a Video CD with PBC function.
• Repeat Playback may not work properly depending on the type of the
disc being used.
You can locate the beginning of a title, chapter, group or track.
During playback or while stopped
1 Press ON SCREEN twice to access the on-screen bar.
2 Press _ b. to select "_",
then press ENTER.
3 Press/\_
to select the desired item, then press ENTER.
• Skip this step for Video CD and Audio CD.
For DVD-RAM/RW/R, DVD VIDEO
"TITLE SEARCH" or "CHAPTER SEARCH" is selectable.
SEARCH" only is selectable while stopped.)
For JPEG, MP3
"GROUP SEARCH" or "TRACK SEARCH" is selectable.
For Video CD, Audio CD
"TRACK" is selectable.
("TITLE
OPERATIONS ON DVD DECK
4
Press the number keys to enter the desired item number, then
press ENTER.
• Playback starts from the selected section.
Examples:
[] To select track 5, press the number key "5".
[] To select track 15, press the number key "1" and "5".
[] To select track 25, press the number key "2", then "5".
If you have specified a wrong selection
Press CANCEL or CLEAR (m) to clear the wrong number, then
enter the correct one before you press ENTER in this step.
To clear the on-screen
Press ON SCREEN.
bar
NOTES:
• When "@" is displayed on the TV screen ill step 4, the chapter you
have selected is not contained in the disc, or chapter search does not
work on the disc.
• Before you press ENTER, playback may start automatically when you
enter the section's number depending on the disc.
• This function is not possible for a Video CD with PBC function.
TimeSearch
EN35
SimulatedSurroundEffect
It is possible to get a simulated surround effect from your stereo
system. You can enjoy the virtual surround sound with your
2-channel stereo system.
1 Press ON SCREEN twice to access the on-screen bar.
2
Press _ t > to select "li'i'[@"ii'il",
then press ENTER.
• Above the selected item, "3D-ON" appears and Simulated Surround
Effect is activated.
• Each time you press ENTER, "3D-ON" appears and disappears
alternately.
To clear the on-screen
Press ON SCREEN.
bar
To cancel the simulated surround effect
Press ENTER to clear "3D-ON" from the screen.
You can play back a disc from the desired point by specifying the
elapsed playing time from the beginning of a title (DVD-RAM, DVDR, DVD-RW and DVD VIDEO) or a disc (Video CD and Audio CD).
1 Press ON SCREEN twice to access the on-screen bar.
2 Press _ L>to select "C)_", then press ENTER. The pop-up
window appears under the selected item.
NOTES:
• The simulated surround effect works correctly only when playing back
a title recorded in multichannels.
• Simulated Surround Effect does not affect the DVD VIDEO bitstream
signal from the DIGITAL AUDIO OUTPUT connector.
• When Simulated Surround Effect is activated, the settings of
"ANALOG AUDIO OUT" and "D. RANGE CONTROl" are disabled.
(__"pg. 73)
Adjusting
ThePictureQuality
3 Press
the number keys to enter the time, then press ENTER.
Playback starts from the specified time.
Example:
To play back from a point 12 (minutes): 50 (seconds) elapsed.
Press 1
Press 2
Press 5
Press 0
You can obtain optimal picture quality by selecting an appropriate
picture mode.
1 Press ON SCREEN twice to access the on-screen bar.
Press 4 P* to select "_",
then press ENTER. The pop-up
window appears under the selected item.
3 Press/\V
to select the desired option, then press ENTER.
NORMAL:Normally select this option.
OINEMA:Suitable for a movie disc, etc.
If you
Press
whole
one(s)
have specified a wrong selection,
CANCEL (for the last entered number) or CLEAR (m) (for
numbers) to clear the wrong number, then enter the correct
before you press ENTER in this step.
To clear the on-screen
Press ON SCREEN.
bar
NOTES:
• When "@" is displayed oil the TV screen in step 3, you have selected
a point that excesses the recording time of the disc.
• Some DVD VIDEO discs do not contain time information,
and it is not
possible to use the Time Search function. In such cases, "@" is
displayed on the TV screen as well.
• This function is not possible for a Video CD with PBC function.
SHARP: Clearer, sharper-edged picture when viewing images with
lots of flat, same-colored surfaces such as cartoons.
SOFT: Select this option when too much noise appears.
To clear the on-screen bar
Press ON SCREEN,
36 EN
OPERATIONS
ON DVD DECK
[]
[]
To select track 15, press the number
To select track 25, press the number
key "1" and "5".
key "2" and "5".
If you have specified a wrong selection
Press CANCEL. The last selection is erased.
_0=9
Or press CLEAR (n). The whole selection is erased.
CANCEL
ONSCREEN
ENTER
b4_
.........
CLEAR(m}
4 Press I_. Playback starts in the programed order.
• When all of the programed tracks have been played back, Program
Playback stops, but the programed information remains.
• To add tracks to the end of the program, perform steps t through 3.
• During Program Playback, pressing i1,-I_1skips to the next selection of
the program. Pressing I_1_1returns to the beginning of the current
selection.
To clear the on-screen
Press ON SCREEN.
bar and the contents of the program
To cancel Program Playback
Press _ L> to select "PRGM", then press ENTER.
NOTE:
Program Playback is not possible depending on the type of disc.
Random
Playback
SettingTheProgressiveMode
You can obtain optimal picture quality by selecting whether the
content on the disc is processed by field (video source) or by frame
(film source).
1 Press ON SCREEN twice to access the on-screen bar.
Press 4 [->to select '_",
then press ENTER. The pop-up
window appears under the selected item.
3 Press/\V
to select the desired option, then press ENTER.
You can play back all the tracks on the disc in random order.
While stopped
1 Press ON SCREEN twice to access the on-screen bar.
Press _ L>to select "RND", then press ENTER. Playback starts
in random order.
VUDEO_CD
To clear the on-screen
Press ON SCREEN.
bar
AUTO1: Used
to play a disc containing both video and film source
materials. This system recognizes the source type (video or film)
of the current disc according to the disc information. Normally
select this option.
AUTO2: Almost the same as the "AUTO 1", but the processing of
the scenes with movement is different. Select "AUTO 1" or
To cancel Random Playback
Perform steps 1 and 2.
NOTE:
The sarne track will not be played back rnore than once during Random
Playback.
"AUTO 2" to your preference.
for playing back a progressive scanned film source
disc.
VIDEO: Suitable for playing back a video source disc. The outlines
on the played back pictures will be soft.
SelectTheSwitchingIntervalOf The SlideShow
FILM:Suitable
To clear the on-screen
Press ON SCREEN.
bar
Press _ [.'-"to select ,,1_,,, then press ENTER. The pop-up
window appears under the selected item.
ProgramPlayback
You can play back up to 30 tracks
in the desired
order.
While stopped
1 Press ON SCREEN twice to access the on-screen bar.
Press 4 b>to select "PRGM", then press ENTER. The program
table appears under on-screen bar.
3 Press the number keys to
enter the track numbers in the
desired order.
Examples:
[] To select track 5, press the
number key "5" and ENTER.
You can control the switching interval of the slide show.
1 Press ON SCREEN twice to access the on-screen bar.
3
Press/\_
to select the desired option, then press ENTER.
• Each time you press/\V, the interval changes as follows:
5 SEC. *-,- 10 SEC. *-,- 15 SEC. *-,- 20 SEC. *-,- 25 SEC. *-,30 SEC. *-* (Back to the beginning)
To clear the on-screen bar
Press ON SCREEN.
OPERATIONS ON DVD DECK
1 1 Press the number keys to enter the same password
step 8 above, then press ENTER.
| ParentalLock
EN37
as in
1 2 Press SET UP twice to complete the setting.
NOTE:
Remember your password, or make a note of it.
This function restricts playback of DVD VIDEO discs which contain
violent (and other) scenes according to the level set by the user.
For example, if a movie which includes violent scenes supports the
parental lock feature, such scenes which you do not want to let
children view can be cut or replaced by other scenes.
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TV/CABLE/DBS/DVD
switch to DVD.
ToChangeTheSettings
You can change the Parental lock settings later.
1 Perform steps 1 to 5 of "To Set Parental Lock For The First
Time" to access the "PARENTAL LOCK" screen before continuing.
To change the level
2 Press/\V
3 Press/\V
To change
4 Press/\V
[email protected]/DVD--
to select "PARENTAL LEVEE', then press ENTER.
to select the desired level, then press ENTER.
the country
code
to select "COUNTRY CODE", then press ENTER.
Press/\V
to select your country code, then press ENTER.
• See "Country/Area Code List for Parental Lock" (: _"pg. 89).
--0=9
Press the number keys to enter the same password as in
step 8 of "To Set Parental Lock For The First Time", then press
ENTER.
ENYER
--
--
[:
7 Press SET UP twice to complete the setting.
SEfUP--
NOTE:
If you forget your password, enter "8888" in step 6.
t'i_[
-1
rii -]
ToTemporarilyReleaseParentalLock
When you set the parental lock level strictly, some discs may not be
played back at all. When you insert such a disc and try to play it
back, the confirmation screen appears on the TV screen, asking
you whether you want Parental Lock to be temporarily released or
not.
Jvc
ToSet Parental LackFarTheFirstTime
While stopped
1 Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press _ b. to select "DVD SET UP", then press ENTER.
4
Press _ [.>to select "UTILITY",
then press ENTER.
5 Press/\V
to select
_1Adb!OOUI_W
II
"PARENTAL LOCK", then press
ENTER.
Press/xV
to select
"PARENTAL LEVEE', then press
ENTER.
7 Press zf\V to select the desired
level, then press ENTER.
• The smaller the value of level is,
the more restrictive the Parental
Lock level becomes.
• Select "NONE" to cancel the
restriction.
Press the number keys to
enter your desired four-digit
number, then press ENTER.
• If you made a mistake, enter a
correct number again.
Press/_V
to select
"COUNTRY CODE", then press
ENTER.
1 0 Press/\V
to select your
country code, then press ENTER.
• If you do not need to change your country code, jump to 12.
• See "Country/Area Code List for Parental Lock" (2" pg. 89)
Ur!L!IYI
1 Load a disc.
• If the disc is rated higher than the selected level, the confirmation
screen appears.
Press 4 b> to select "YES", then press ENTER.
• If you select "NO", you cannot play back that disc.
3 Press the number keys to enter the same password as in
step 8 of "To Set Parental Lock For The First Time", then press
ENTER.
• When you enter the correct password, the Parental Lock is released
and the unit starts playback.
• If you enter a wrong password, "ENTRY ERROR RETRY" appears on
the TV screen. Enter the correct password.
• If you have successively entered wrong password three times,
"ENTRY ERROR CAN NOT CHANGE PASSWORD" appears on the
TV screen. In such a case, press ENTER. The disc will stop. Then
play back the disc again, and try the procedure again from step t.
NOTE:
If you forget your password, enter "8888" in step 3.
38 EN OPERATIONS
ON DVD DECK
NOTES:
| BasicRecording
|
|
_:,÷_ _
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TV/CABLE/DBS/DVD switch to DVD.
ATTENTION:
It is not possible to record programs Oila DVD-R disc which has
already been finalized.
• It is recornmended
to format a DVD-RAM disc before use if you use
the disc on this unit for the first time.
• When using a brand-new DVD-RW disc, format the disc either in VR
mode or in Video mode. (_ pg. 78)
• Recordings
made on DVD-R/RW
disc must be finalized to play back
on other DVD players. Perform "Finalize A Disc (DVD Deck Only)"
(_ pg. 79)
• You can record up to 99 programs and 999 play lists on each disc.
• Some programs can only be recorded one time.
• When recording is started, an index of the first part of recording is
automatically
recorded. (_ • pg. 55) To record satellite programs, refer
to page 46. To delete the index, refer to page 57.
• Recording sometimes may stop or cannot be performed even if there
is enough available capacity remaining on the disc.
RecordingResumeFunction
[email protected]|1
If there is a power outage during recording,
Instant Timer
Recording
(ITR) (_ . pg. 39) or timer recording
(_ . pg. 41,42,
43),
the recording
will resume automatically
when power is restored
the unit unless the unit's memory
backup has expired.
Recording Mode
MPEG2 format is used as recording format. As a guide for picture
quality, the "bps" unit is used to represent how much data can be
recorded per second. The larger this value is, the better the picture
quality becomes but more capacity is required for the recording.
Select XP or SP for programs where quick movement occurs, such
as sports programs, and LP or EP for talk shows, etc. with
relatively less movement.
The recording modes for a 4.7 GB disc are set as follows:
I
m
V(R/DVD
RECMODE
CH+/=
VCR/DVD-_0=9
Recording
mode
[]
--
_r _
--
1 hour
SP
5 Mbps
2 hours
LP
2 Mbps
4 hours
EP
1.6 Mbps
6 hours
( " pg. 40)
Jvc
FR420
FR480
a recordable
• For details,
Press
the unit.
disc.
refer to "Placing
VCR/DVD
3 Press CH +/wish to record.
A Disc" (:y" pg. 11 ).
repeatedly
or the number
4 Press REC MODE
• Each time you press
follows:
so that the DVD
keys
to select
lamp lights
the channel
up on
you
repeatedly
to set the recording
mode.
REC MODE, the recording mode changes
as
XP _ SP _ LP _ EP _ FR_
(Back to the beginning)
* The value is selectable from 1 to 6 hours in 5-min. increment, from 7 to
8 hours in 1-hour increment by pressing ,'
repeatedly after selecting
"FR60-FR360';
"FR420" and "FR480'! To change the value in 30-min.
increments, press and hold
• For details on the recording mode, see the right column.
Press
•
on the unit to start
recording.
Or press
and hold •
and
press I_ on the remote control.
• The DVD recording lamp lights up on the unit.
6 Press II to pause recording.
• To resume recording, press I_.
7 Press • to stop recording.
• The DVD recording lamp lights off on the unit.
• It takes about 10 seconds to end the writing session
recording.
when you stop
Maximum recording
time (approx,)
10 Mbps
FR60-FR360
(H ÷/-
Load
Recording amount
(approx.)
XP
||
RECMODE--
1
to
1 - 6 hours
The amount varies
depending on the
selected time.
7 hours
8 hours
OPERATIONS
•
•
•
•
EN 39
InstantTimerRecording(ITR)
| Recording
Features
|
ON DVD DECK
|
_:,÷_ _
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD
switch to DVD.
Press VCR/DVD repeatedly so that the DVD lamp lights up on the
unit.
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-min. increments), and shuts the unit off after
recording is finished.
1 Press • on the unit to start recording.
2 Press • again to engage the ITR mode.
• On the front display panel, "0:30" appears.
3 If you want to record for more than 30 minutes, press • to
extend the time. Each press extends recording time by 30 minutes.
NOTES:
• You can only perform ITR using the • button on the unit.
• When the recording capacity becomes full during timer recording or
Instant Timer Recording, the unit is automatically shut off.
WatchAnotherProgramWhile RecordingOn TheUnit
While recording is going on, you can watch another program on the
TV by using the TV's tuner.
@
(_fC3 C-20
CTb
c_J
_Tj
de_J
NOTE:
It is required that the remote control is set to be able to operate tile TV
in advance. (:y" pg. 70)
1 During recording, press TV/VCR to select TV mode if your unit
is connected to the TV via the RF connection.
• VCR mode is disengaged, then the VCR indicator lights off and "TV"
appears on the front display panel.
C_
d_
CT3
c£_J d_b C£_J
--DISPLAY
DVD
E L_
|
VCR indicator lights off,
t,l[
-1
• The program received on the TV's tuner is displayed on the TV
screen.
Slide the TV/CABLE/DBS/DVD
switch to TV.
rii -]
(H+/,Jv_
3 Press CH +/- repeatedly to select the desired channel.
ElapsedRecordingTimeAndDiscRemainingTime
Indication
During recording,
press DISPLAY
repeatedly
until the desired
indication
appears
on the front display panel.
• Each time you press DISPLAY, the time indication changes as
follows:
Elapsed recording time -, Disc remaining time -, Clock -, (Back to
the beginning)
• There is another way to check the disc remaining time. While the unit
is stopped or recording is in progress, press REMAIN
The list of disc
remaining times for all recording modes appears on the TV screen.
40 ENOPERATIONSON DVD DECK
FreeRate Function
NOTES:
To record the entire program, the unit automatically set the
appropriate recording mode depending on the combination of the
total time of the program to be recorded and either the remaining
disc space or the specified recording time (from 60 minutes to 480
minutes).
• To record the entire program within the actual remaining
disc space
Select "FR (JUST)" in a recording mode selection procedure.
( _ pg. 41,42)
• Note that this function is available only for timer programing
recording.
• To record the entire program by specifying the desired
recording time
Select "FR60-FR360", "FR420" or "FR480" in a recording mode
selection procedure. (: -" pg. 38, 41,42)
•
To record a 25-min.
same disc for example
long
daily
program
five times
just on a
Perform "VCR Plus+ _ Timer Programing"
(_ _ pg. 41 ) procedure.
Be
sure to set the recording
mode to "FR125"
and set Weekly/Daily
Rec Function
to "MON-FRI"
in step 6 to fit the total recording
time
to the whole disc space.
B:
C:
D:
I E:
__'_/
is recorded
in SP mode
cannot be recorded.
B:
C:
D:
E:
_
__
instead
of in
2nd
3rd
4th
Blank (20 rnin.)
A 1st
SecondAudioRecording
This
unit's
built-in
MTS decoder
enables
reception
TV Sound broadcast.
To record a SAP program
AUDIO RECORD"
to "ON". (: _ pg. 74)
of Multichannel
received,
set "2ND
NOTE:
A: 1st
When the same program
"FR 125", the 5th program
i/f:!
2nd
3rd
4th
5th
• You can program this unit to timer-record,
regardless of the disc
remaining time. When the disc remaining time is not enough,
recording may stop in the middle of a program. To avoid this, make
sure of the disc remaining time before setting timer-programing.
(Example)
If you programed to timer-record
for 60 minutes in SP
mode on a 120-minute disc, the disc remaining time would be 30
minutes in XP mode, 60 minutes in SP mode, 120 minutes in LP
mode, 180 minutes in EP mode, and 240 minutes in FR480 mode.
Timer-recording
will not complete beyond these remaining times.
• The maximum recording time of FR (JUST) mode is the same as the
recording time of FR480 mode. When timer-programing
a long
program in FR (JUST) mode on a disc whose remaining time is short,
it is recommended
checking the disc remaining time in FR480 mode
to see if the remaining time is enough for the program.
• Even if more than one program are timer-programed
in FR (JUST)
mode, only the first one is recorded.
• In order to ensure that the recording fits on the disc, this feature may
leave a slight non-recorded
section at the end of the disc.
• There may be some noise and sound disturbance
at the point on the
disc where the unit switches the mode.
When the channel is changed on tile unit;
• The "MONO" indicator appears on the screen for about 5 seconds if
the program is a monaural broadcast.
• The "STEREO"
indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
• Both "STEREO"
and "SAP" indicators appear when a stereo program
is accompanied
by SAP sound.
• Both "MONO" and "SAP" indicators appear when the main audio on
the monaural broadcast is accompanied
by SAP sound.
OPERATIONSON DVD DECK EN41
6
| VCRPlus+®TimerPrograming
.......
i
You can program this unit to timer-record as many as 8 programs.
With the VCR Plus+ system, timer programing is greatly simplified
because each TV program has a corresponding code number
which your unit is able to recognize.
You can use the remote control to enter the PlusCode number.
•
•
•
•
Make sure that the unit's built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD
switch to DVD.
--0=9
CANCEL
-VCRPLUS+
-ENTER
CLEAR
Iml --
..........
_r
_
RETURN
c_
dvc
1
2
Load a recordable disc.
Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.
3 Press VCR PLUS+ to access the VCR Plus+ screen.
4 Press the number keys to
enter the PlusCode number of a
program you wish to record, then
press ENTER.
• If you have made a mistake, press
CANCEL and input the correct
number before you press ENTER.
• To clear all entered numbers at a
time, press CLEAR(m),
• If the number you entered is invalid, "PLUSCODE NO. ERROR
CONFIRM PLUSCODE NO. THEN RETRY" appears on the TV
screen. Input a valid PlusCode number.
• If "GUIDE PROGRAM IS NOT SET SELECT CHANNEL YOU WANT
TO RECORD" appears on the TV screen, set Guide Channel
Numbers manually. (y" pg. 77)
• When "PROGRAM FULL DELETE UNWANTED TIMER PROGRAM"
appears on the TV screen, you need to cancel some of the reserved
programs. (y" pg. 45)
5 The PlusCode number you entered and the matching timerrecording information are displayed on the TV screen. Check the
program data.
• To cancel this setting, press VCR PLUS+ or RETURN.
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see "Changing VCR Plus+_ Setting" (_" pg. 77) and
set the Guide Channel number correctly.
Press
_ P* to select
the desired
recording
option
as required.
Press/\V
to select the desired
setting, then press ENTER.
• "STOP" (To advance/go
back the stop time by 30 minutes, press
hold/\X').
• "DAILY/WEEKLY"
(_ . pg. 41, "Daily/Weekly
Recording"))
• "REC MODE" (.:" pg. 38, "Recording
Mode")
• "NAME" ( "pg. 57, "Modify Program Name")
7
Press
ENTER
to access
8
Press
ENTER
to complete
the Program
timer
Confirmation
screen.
programing.
• To program another timer, repeat steps 3 - 8.
• If "PROGRAM
OVERLAPPED"
appears on the TV screen,
page 45.
9
Press
DVD
TIMER
(®) to engage
and
the unit's
timer
see
mode.
The
DVD timer lamp lights up on the unit and the VCR deck is
automatically
selected.
When the VCR deck is in timer standby
mode, the unit is automatically
turned off.
• To disengage the timer mode, press DVD TIMER (®) again.
NOTES:
• There rnay be cases that VCR Plus+ Timer Programing function
prolongs the stop time of the programing.
• When two successive
programs are recorded on a DVD-RW disc with
VCR Plus+ Timer Programing function, the beginning of the second
one may be left off the recording.
• VCR Plus+ Timer Programing
is not possible on the discs used
exclusively for On-Disc Timer Programing.
• If the copy limited program is received during timer-recording,
the unit
enters Record Pause mode. Recording starts again if it is switched to
a recordable
broadcast during the time you programed.
IMPORTANT:
If you have moved to a different area or if a broadcasting
station's
channel number has been changed, the wrong channel number will
be displayed on the VCR Plus+ program screen in step 5. When this
happens, set the correct Guide Channel number for that station.
(_" pg. 77, "Changing
VCR Plus+ _ Setting")
Cable Box and DBS Receiver Users
To timer-record a satellite broadcast using the VCR Plus+
system:
[] Perform "Cable Box and/or DBS Receiver Control Setting
(DVD Deck Only)" (7. pg. 22).
[] Perform "VCR Plus+ _Timer Programing" (_ _"pg. 41 ).
[] Leave the cable box or DBS receiver's power on.
Daily/Weekly Recording
You can record
timer settings.
programs
WEEKLY:
Select
MON-FRI:Select
Friday.
MON-SAT:
Saturday.
SUN-SAT:
Saturday.
Select
Select
with one of the following
to record a weekly program.
to record a daily program
from
to record
to record
a daily program
a daily program
from
from
weekly/daily
Monday
Monday
Sunday
through
through
through
42 EN OPERATIONS
ON DVD DECK
1 0 Press ENTER to access the Program Confirmation
| ManualTimerPrograming
You can program this unit to timer-record as many as 8 programs.
If you do not know the PlusCode number for the program you wish
to record, use the following procedure to set your unit to
timer-record the program.
•
•
•
•
Make sure that the unit's built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD
switch to DVD.
1 2 Press DVD TIMER (Q) to engage the unit's timer mode. The
DVD timer lamp lights up on the unit and the VCR deck is
automatically selected. When the VCR deck is in timer standby
mode, the unit is automatically turned off.
• To disengage the timer mode, press DVD TIMER (®) again.
NOTES:
• When two successive programs are recorded on a DVD-RW disc with
Manual Timer Programing function, the beginning of the second one
may be left off the recording.
• If the copy limited program is received during timer-recording, the unit
enters Record Pause mode. Recording starts again if it is switched to
a recordable broadcast during the time you programed.
Cable Box and DBS Receiver
C--_
dYJ
C--_J
""
:
ATTENTION
_r j
Jvc
1 Load a recordable
disc.
2 Press VCR/DVD repeatedly
the unit.
3 Press PROG/CHECK
Users
To timer-record a satellite broadcast using Manual Timer
Programing:
[] Perform "Cable Box and/or DBS Receiver Control Setting
(DVD Deck Only)" (_ _"pg. 22).
[] Perform "Manual Timer Programing" (_ • pg. 42).
[] Leave the cable box or DBS receiver's power on.
PROG/(HE(K
=
ENTER._,_,_
screen.
1 1 Press ENTER to complete timer programing.
• To program another timer, repeat steps 3 - 11.
so that the DVD lamp lights up on
to
access the Program Check
screen.
• When "PROGRAM FULL DELETE
UNWANTED TIMER PROGRAM"
appears on the TV screen, you
need to cancel some of the
reserved programs. (:" pg. 45)
4 Press/_V to select "NEW
TIMER PROGRAM", then press
ENTER. The program screen
appears.
Press/\V
to set the desired
date.
• The current date appears on the
TV screen. The date you enter
appears in its place.
Press *C b. to select "START", then press/\V
to set the desired
start time.
• Each press of/'_7 advances/goes back the start time in 1-min.
increments.
• To advance/go back the start time in 30-min. increments, press and
hold 'J.
7 Press 4 b> to select "STOP", then press/\V
to set the desired
stop time.
• Each press of/_,'_;_advances/goes back the stop time in 1-min.
increments.
• To advance/go back the stop time in 30-min. increments, press and
hold _'_7.
8 Press _ b. to select "CH", then press/\V
to select the desired
channel.
• If you are using a DBS receiver, see "ATTENTION FOR DBS
RECEIVER USERS" in the right column.
Set the other recording options as required.
• Refer to step 6 in "VCR Plus+° Timer Programing" (:y" pg. 41).
FOR DBS RECEIVER USERS
If you are using a DBS receiver (unless "DBS RECEIVER SET"
is set to "OFF" : • pg. 22), the band indication (TV, CATV or
DBS) appears on the left of the channel number indication.
Noindication:To timer-record a regular TV broadcast received
on the unit.
CATV: To timer-record a cable TV broadcast received on the unit,
or through a cable box (unless "CABLE BOX SET" in set to
"OFF"
pg. 22).
DBS:To timer-record a satellite broadcast received through a
DBS receiver.
NOTE:
If the channel number entered requires that the band be set,
"7=DBS" is displayed on the screen.
If this happens, press the number key "7" to select "DBS".
OPERATIONSON DVD DECK EN43
7
II 0n-DiscTimer Programing
,
..o
iiij_
i
¸_'_
i=__
ii
Press
4 b" to select
i
On-Disc Timer Programing is a function used with discs that are
especially intended for a specific program. The disc is then
programed for a program you always watch every day or every
week. Since older programs are automatically overwritten, a single
DVD-RAM/RW (VR mode) disc can be used without worrying
about how much recording capacity remains. (_" pg. 44)
You can program each disc to timer-record as many as
8 programs.
8 Press
channel.
4 b. to select
Make sure that the unit's built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD
switch to DVD.
"CH",
then
recording
ENTER
to access
ENTER
to complete
• On-Disc Timer Prograrning
is possible only with the disc for OnDisc Timer Programing.
• If data is recorded on a disc for On-Disc Timer Programing using a
unit from another manufacturer,
On-Disc Timer Programing may no
longer function properly.
• To program
_rf6_D
CYJ
C_
C--_
press/\V
options
1 2
C_J
CT_
to set the desired
to select
the desired
FOR DBS
as required.
• You can select XP, SP, LP, EP or FR480 mode for "REC MODE".
However, you cannot select FR (JUST), FR60-FR360
and FR420.
• Refer to step 6 in "VCR Plus+ _ Timer Programing"
(y" pg. 41 ).
• It is not possible to use the Free Rate function. (:2" pg. 40)
1 1 Press
C--J
press/\V
Set "DAILY/WEEKLY"
option.
• Refer to step 6 in "VCR Plus+ _ Timer Programing"
(y" pg. 41 ).
• It is necessary to set "DAILY/WEEKLY"
option for On-Disc Timer
Programing.
(:J" pg. 41, "Daily/Weekly
Recording")
ATTENTION:
CWD
CTJ
then
• If you are using a DBS receiver, see "ATTENTION
RECEIVER
USERS" (:y" pg. 42).
1 O Set the other
•
•
•
•
"STOP",
stop time.
• Each press of/"<;
advances/goes
back the stop time in 1-min.
increments.
• To advance/go
back the stop time in 30-min. increments,
press and
hold _":_
v.
Press
another
timer,
the Program
timer
Confirmation
screen.
programing.
repeat steps 3 - 12.
Cable Box and DBS Receiver
Users
To timer-record a satellite broadcast using the On-Disc Timer
Programing function:
[] Perform "Cable Box and/or DBS Receiver Control Setting
(DVD Deck Only)" (_, pg. 22).
[] Perform "On-Disc Timer Programing" (>" pg. 43).
[] Leave the cable box or DBS receiver's power on.
ToTimer-recordTheProgramWith TheProgramedDisc
1
Load
a programed
disc.
2 Press DVD TIMER
(®). The unit turns off and "®"
appears
on the front display panel. The DVD timer lamp also lights up on
the unit and the VCR deck is automatically
selected.
When
VCR deck is in timer standby mode, the unit is automatically
off.
7
_
• To disengage
the timer
mode,
press
the
turned
d_/I again.
NOTES:
iVl
ToMake TheDiscForOn-DiscTimerPrograming
1 Load
a recordable
2 Press
the unit.
VCR/DVD
3
PROG/CHECK
Press
4
When On-Disc
on the disc
disc.
repeatedly
so that the DVD
to access
Timer
the Program
Programing
is made
lamp lights
Check
up on
screen.
for the first time
Press/\V
to select "DISC TIMER
PRGM",
then press ENTER.
• When some programs are recorded on the disc, a caution message
appears. In such a case, backup the programs as required, then
format the disc before making On-Disc Timer Programing.
(:y" pg. 78)
When
On-Disc
the disc
Press/\V
ENTER.
5
Press/_V
Timer
to select
Programing
"NEW
TIMER
to set the desired
• The current date appears
appears in its place.
has already
PROGRAM",
been
made
on
then press
date.
on the TV screen.
The date you enter
6 Press _ b" to select "START",
then press/\V
to set the desired
start time.
• Each press of/'_7
advances/goes
back the start time in 1-min.
increments.
• To advance/go back the start time in 30-min. increments, press and
hold/' '_;.
• Even if On-Disc Timer Prograrning
is overlapping with other timer
programing,
any caution message does not appear. In such a case,
recording will be executed in the descending
order of the recording
start time of the program.
• On-Disc Timer Programing is not possible on a DVD-RW disc
formatted in video mode. (:" pg. 78)
• The information
of a program recorded with On-Disc Timer
Programing
is not stored in the library. (.:2" pg. 60)
• The play list is not created for the programs recorded with On-Disc
Timer Programing.
(:" pg. 58)
• VCR Plus+ Timer Programing
is not possible on the discs used
exclusively for On-Disc Timer Programing.
• Manual Timer Programing is not possible on the On-Disc Timer
Programed
disc. (:_" pg. 42)
• Basic Recording is not possible on the On-Disc Timer Programed
disc. (:y" pg. 38)
• The On-Disc Timer Programing function does not work on the unit
form other manufactures
even if the On-Disc Timer Programed
disc is
loaded.
• The beginning of a program may not be recorded. Also, if the 1st
program's recording stop time and the 2nd program's recording start
time is the same, the ending of the 1st program may not be recorded.
• If there is a power cut while recording, the recordings before the
power cut are not guaranteed.
44 E. OPERATIONS
ON DVD DECK
How DiscsAre Overwritten
(Example 1)
To record a 1-hour serial drama every Friday in SP mode
Overwritten
Overwritten
2nd
/
!i
i,
N2
i
\
The first program is
overwritten by the third.
(Example 2)
To record a 15-minute serial drama every morning in XP mode
!2/6/
_.\ 12J3
•
'_i
:_
3rd
12/5
2nd
i
12/4/"'
//
(Example 3)
To record a 90-minute serial drama every Sunday in SP mode
S[d
'
y--_
/
Areas treated as blank cannot
recorded
material.
NOTE:
On-Disc Timer Programing may not always work as these examples.
y
be played
"_
back even ifthey contain
The second program is
overwritten by the forth.
OPERATIONS ON DVD DECK
DVDTIMER
1®) °-'°
VCR/DVD
dZCD C_J
C_
C_J
CMICEL
PROG/CH[CK
.......
C_3
C_J
C_4D
7°_O/I
C_3
C_]
=
[HYER--
t'i/_
[::
rii -]
EN45
Program's
information
on the front display panel
You can check the details of the programs even when the power
is turned off. (It is necessary that the Power Save mode
(
pg. 74) is disengaged or the unit is not in timer standby
mode.) However, it is not possible to cancel or change the
program's setting.
[] Press PROG/CHECK.
• "NEW PROG" or "P-I" (if 8 programs have already been set)
appears.
[] Press/\V
until the desired program number ("P-I" to "P-8")
appears, then press ENTER.
[] Press L>.
• Each time you press I:, the indication changes as follows (the
settings in parentheses are examples):
Date ("DATE 03.08SU") _ Start time ("ON 11:00") -* Stop time
("OFF 11:30") _ Channel ("CH 1") _ Weekly/Daily ("MO-FR
DAILY") _ Program number ("P-I") and recording mode (SP) -_
(Back to the beginning)
[] Press PROG/CHECK to complete checking.
• The normal display resumes.
Check,CancelAndChangePrograms
WhenProgramsOverlapEachOther
1 When the DVD timer lamp lights on the unit
Press DVD TIMER (®), then press tb/l.
If "PROGRAM OVERLAPPED" appears, you have another
program overlapping the program you have just made.
Confirm with the arrow on "OK", then press PROG/CHECK.
Program Check screen appears and conflicting programs will be
highlighted in pink.
When "_"
lights on the front display panel and the DVD
timer lamp also lights up on the unit.
Press d>/I.
When "R-LK" lights on the front display panel
Press REC LINK on the unit, then press O/I.
When the DVD lamp does not light up on the unit
Press VCR/DVD repeatedly so that the DVD lamp lights up on the
unit.
2 Press PROG/CHECK
to
access the Program Check
screen.
• To return to the previous screen
after you check the program, press
PROG/CHECK again.
To cancel the program
Press/\V
to select a program to
be cancelled, then press
CANCEL.
3 Press z'\V to select the program, then press ENTER. The
program screen appears.
4 Change the settings of the desired recording options as
required.
• Refer to steps 5 - t0 in "Manual Timer Programing" (:y" pg. 42).
5 Press PROG/CHECK to complete timer correction. The
previous screen resumes.
6 For VCR Plus+, Manual or On-Disc Timer Programing
Press DVD TIMER (®).
For Automatic Satellite Program Recording
Press REC LINK on the unit for 2 seconds or more.
• The DVD timer lamp also lights up on the unit and the VCR deck is
automatically selected. When the VCR deck is in timer standby
mode, the unit is automatically turned off.
Example: Program 3 (you have
just made) and Program 4
overlap each other.
I Confirm the overlapping
programs. Overlapping programs
appear on the TV screen.
NOTE:
If you do not rnind this overlap, press
PROG/CHECK to finish the timer
program setting. The program with the lower program number will be
recorded and the other one will not be recorded correctly. If no changes
are made for approximately 1 minute, the unit will return to the normal
screen.
2 Press z'\V to select the desired program to be cancelled or
changed.
To cancel the program
Press CANCEL.
• "THE TIMER PROGRAMING SETTING WAS CANCELLED" appears
on the TV screen for about 5 seconds, then the normal screen
resumes.
To change the program setting
Press ENTER, then go to step 3.
3 Change the program setting.
• Refer to steps 5 - 10 in "Manual Timer Programing" (:y" pg. 42).
4 Press PROG/CHECK to check if the conflict has been settled.
Program check screen appears.
5 Engage the unit's timer mode.
• Refer to step 6 in "Check, Cancel And Change Programs"
(_ pg. 45).
NOTE:
When any overlaps remain after deletion and rnodification of programs,
Program Check screen remains showing the conflicting programs. In
such a case, repeat the procedure above until the conflict is solved.
46 EN OPERATIONS
ON DVD DECK
• Make sure the DBS receiver
I Automatic
Satellite
Recording
(DVDDeck
Only) Program
1
This function allows you to automatically record a satellite program
which is timer-programed on your external DBS receiver. Connect
a DBS receiver to the unit's AUDIO/VIDEO INPUT (L-1) connectors
and program the timer on the DBS receiver. The unit starts or stops
recording by the signals input from the DBS receiver. After
recording, the unit's power shuts off automatically.
• You can also connect the cable box if it has a timer.
ATTENTION:
• Be sure not to turn on the DBS receiver before the program is
executed; otherwise, the unit will start recording when the DBS
receiver's power is turned on.
• If you have connected another appliance other than a DBS
receiver to the AUDIO/VIDEO
INPUT (L-1) connectors,
be sure not
to engage the Automatic
Satellite Program Recording mode;
otherwise, the unit will start recording when the connected
appliance's
power is turned on.
• Automatic Satellite Program Recording and timer-recording
cannot
be done at the same time.
<.!_
/I
is connected
Press
the unit.
VCR/DVD
2
Press
REC
3
Press
and hold
repeatedly
MODE
so that the DVD lamp
repeatedly
REC
LINK
to set the recording
on the unit for about
RE(MODE
VCR/DVD _
C_=J
C1_
d_7
(lg_J
C_J
CI_3
C¢_
C_2J
C_D
ic2D _
RECNODE_
_r _
_oo
0
C_
RE( LINK
lights up oil
mode.
2 seconds
to
engage the Automatic
Satellite
Program Recording
mode. "R-LK"
appears
on the front display panel and the VCR deck is
automatically
selected.
When the VCR deck is in timer standby
mode, the unit is automatically
turned off.
NOTES:
• To disengage the Automatic Satellite Program Recording mode,
press REC LINK.
• If the unit's power is off, it is not possible to engage the Automatic
Satellite Program Recording mode.
• In step 3, if "R-LK" blinks quickly on the front display panel even
though your DBS receiver's power is off, Automatic
Satellite Program
Recording will not work properly with that satellite receiver*. If this is
the case, perform "Manual Timer Programing"
(:" pg. 42) to
timer-record
a satellite program.
* Some DBS receivers output signals even if the power is off. Automatic
Satellite Program Recording is not possible with those DBS receivers.
• "R-LK" blinks on the front display panel while Automatic Satellite
Program Recording is in progress.
• For timer programing
of the DBS receiver, refer to the instruction
manual of the DBS receiver.
• Automatic Satellite Program Recording
receiver does not have a timer.
VCR/DVD
to the unit's AUDIO/
VIDEO INPUT (L-l) connectors.
• Program the timer on the DBS receiver.
• Slide the TV/CABLE/DBS/DVD
switch to DVD.
is not possible
if your DBS
• Pressing the unit's d>/Ebutton while Automatic Satellite Program
Recording is in progress turns off the unit's power and disengages
the Automatic Satellite Program Recording mode.
• If there are more than one satellite programs you wish to record with
Automatic Satellite Program Recording, it is not possible to set
different recording modes for each program.
• Depending on the type of DBS receiver, the unit may not record a
slight portion of the beginning of the program or may record slightly
longer than the actual length of the program.
• If you engage the Automatic Satellite Program Recording mode when
the DBS receiver's power is on, the unit will not start Automatic
Satellite Program Recording even though "R-LK" blinks on the front
display panel. When the DBS receiver shuts off once and is turned
back on again, the unit starts recording.
• You can also record a program from your cable system in the same
way if the system has a timer.
About
the Automatic
Satellite
Program
Recording
indicator
on the front
display
panel
When the DVD deck is in the Auto Sattellite
Program
Recording
standby mode while the VCR deck is used, the following
indicator
lights up instead of "R-LK" as illustrated.
dVC
Automatic
indicator
Satellite
Program
OPERATIONS
| BasicPlayback
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TVlCABLEIDBSlDVD switch to DVD.
F_
\
......
I
o r,=
EN 47
1 Load a cassette. Make sure the window side is up, the rear label
side is facing you and the arrow on the front of the cassette is
pointed toward the unit.
• Do not apply too much pressure when inserting.
• If the record safety tab has been removed, playback begins
automatically.
• The unit's power comes on automatically and the counter is reset to
0:00:00.
2 Press VCR/DVD
the unit.
Jve
ON VCR DECK
repeatedly so that the VCR lamp lights up on
3 Find the program start point. If the tape is advanced past the
start point, press _141. To go forward, press 1_1_.
4 Press I_ to start playback.
5 Press • to stop playback.
• To eject the cassette, press _._(VCR EJECT).
VCR/DVD-Cxb_J
i C_
i GriJ
CT_ _
C_J C_J
G_2J _
Clean the video heads using a dry cleaning cassette
- ECL-3F - when:
• Rough, poor picture appears while a tape is played back.
• The picture is unclear or no picture appears.
• "USE CLEANING CASSETTE" appears on the screen (only with
"SUPERIMPOSE" set to "AUTO"). ( "pg. 75)
NOTE:
The heads get dirty in the following cases:
• in an environment prone to extreme temperature or humidity
• in a dusty environment
• flaw, dirt or mold on video tapes
• continuous usage for a long time
Usable
dVC
cassettes
Full-Size VHS
T-30 (ST-30**)
T-60 (ST-60**)
T90
T-120 (ST- 120"*)
T-160 (ST-160"*)
ST-210**
Compact VHS*
TC-20 (ST-C20**)
TC-30 (ST-C30**)
TC-40 (ST-C40**)
* Compact VHS camcorder recordings can be played on this unit. Simply
place the recorded cassette into a VHS Cassette Adapter and it can be
used just like any full-sized VHS cassette.
** This unit can record on regular VHS and Super VHS cassettes.
However, it will record regular VHS signals only.
• S-VHS recording is not possible with this unit.
• This unit is equipped with SQPB (S-VHS QUASI PLAYBACK) that
lets you watch tapes recorded in the S-VHS format and the SP
mode with regular VHS resolution.
• SQPB does not deliver Super VHS resolution.
48 ENOPERATIONSON VCRDECK
High-SpeedSearch
| PlaybackFeatures
•
•
•
•
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TVlCABLEIDBSlDVD switch to DVD.
Press VCR/DVD repeatedly so that the VCR lamp lights up on the
unit.
[email protected]/DVD_
1_ o/i
Ci_J
C_D
(Z#CJ
During playback,
press i_l_ for forward high-speed
search, or _141
for reverse high-speed
search.
• Each press of the button increases the search speed for each
direction.
When pressing i,_l_:
(SP): +5x*-,-+7x
(EP): +1 lx*-,-+2 lx
When pressing 41_1:
Once 41_1 is pressed, reverse search starts in -lx normal playback
speed. After this process, each press of 41_1 changes the search
speed between -5x and -7x in SP mode, -11 x and -21 x in EP mode.
(SP): -1 x_-5x*-,--7x
(EP): -lx_-1
lx*-*-2
lx
• To resume normal playback, press I_.
QuickRewindA Little
Iq3_D
b4_
m--
_r
j
--
11
During playback (or Live Memory Playback), press _.
The unit
rewinds the picture a little (about 7 seconds) and resumes
playback.
• If the button is pressed repeatedly, the unit rewinds the pictures
continuously and resumes playback.
lIE( MODE--
SkipSearch
AtlDIO--
During playback,
sections.
ATTENTION:
In tile search, still, slow-motion or frame-by-frame playback mode,
• the picture will be distorted.
• the noise bars will appear.
• there may be a loss of color.
• you cannot hear the sound.
Still Picture/Frame-By-Frame
Playback
1
Press II to pause during playback.
• If there is vertical jitter, press OH +/-to
2 Press II to activate frame-by-frame
• To resume normal playback, press I_.
correct the picture.
playback.
Slow Motion
1 Press II to pause during playback.
2 Press and hold II for 2 seconds, then release. Press II and
release again to return to still picture.
• The speed changes for each direction by pressing <1_1 and
repeatedly.
• To resume normal playback, press I_.
press
_
1 to 6 times
to skip
over unwanted
• Each press initiates an approximately
30-second period of fastmotion playback. Normal playback resumes automatically.
• To resume normal playback, press I_.
IndexSearch
Your unit automatically marks index
codes at the beginning of each
recording. This function gives you
quick access to any one of 9 index
codes in either direction.
B.....
NOTE:
Before starting, make sure the unit is in
the Stop mode.
Press
"INDEX
I_1_1 or I_1_1 to activate
1" is displayed
Index
+==1=+
....
_i-
REMAU!
COUNT
Search.
on the TV screen
"INDEX
and search
-1"
+ .....
E
INDEX FF1 /
111: [10
1 : 23 : 45
or
begins
in the
corresponding
direction.
• To access index codes 2 through 9, press I<< or I_D,-I repeatedly
until the correct index number is displayed.
Example:
To locate the beginning of B from the current position, press I<<
twice.
To locate the beginning of D from the current position, press I_D,-I
once.
Current position
NOTE:
During slow motion playback, some noise may appear on the TV
screen. Press OH + or - to eliminate the noises.
c o E
-2
-1
1
2
3<--I
/
Index number
• When the specified index code is located, playback begins
automatically.
OPERATIONS
ON VCR DECK
EN49
Next FunctionMemory
Soundtrack
Selection
The Next Function Memory "tells" the unit what to do after
rewinding. Before continuing, make sure the unit is in the Stop
mode.
Your unit is capable of recording three soundtracks (HI-FI L, HI-FI
R and NORM) and will play back the one you select.
During Playback
Pressing AUDIO changes the soundtrack as follows:
For Automatic Start Of Playback
Press _14, then press I_ within 2 seconds.
For Automatic Power Off
Press _14, then press d_/I within 2 seconds.
TRACK
USE
On-Screen Display
For Automatic Cassette Ejection After Tape Rewind
Press _141, then press __ (VCR EJECT) on the unit within 2
seconds.
HI FI
Hi-Fi sound is played back
HI FI L
Sound on the left Hi-Fi channel is
played back
HI FIR
Sound on the right Hi-Fi channel is
played back
1 Press I_ to start playback.
NORM
Sound on the normal track is played
back
2 Press and hold I_ for over 5 seconds, then release.
• _
lights up on the front display panel.
• After playing back a tape 1O0times, the unit stops automatically.
NORM
HI FI
RepeatPlayback
Your unit can automatically
repeatedly.
play back the whole tape 100 times
3 Press • at any time to stop Repeat Playback.
• Pressing I_, 41_1, _
or n also stops Repeat Playback.
Both sounds on the Hi-Fi track and
normal track are mixed and played
back
NOTES:
ManualTracking
Your unit is equipped with automatic tracking control. During
playback, you can override this and adjust the tracking manually by
pressing the CH buttons.
• "HIFI" should normally be selected. In this mode, Hi-Fi stereo tapes
are played back in stereo, and the normal audio track is played back
automatically
for tapes with only normal audio.
• "SUPERIMPOSE"
must be set to "AUTO" or the on-screen
displays
will not appear.(
"pg. 75)
VHS ProgressiveScan
J
| During playback, press
activate manual tracking.
J_
CH + or - on the unit simultaneously
2 Press CH + or - to adjust the tracking manually.
• Press REC MODE again to return to automatic tracking.
NOTE:
When a new tape is inserted, the unit enters the automatic tracking
mode automatically.
to
You can watch the image on VCR deck in the Progressive scan
mode via component video.
ATTENTION:
Your TV needs to be compatible with Progressive and to have
Component video input connectors.
[] Set the Progressive-compatible
TV to the component input
mode.
[] Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit, then press PROGRESSIVE SCAN for 3 or more seconds
so that the Video output indicator (Q) lights on the front display
panel.
[] Press VCR/DVD repeatedly so that the VCR lamp lights up on
the unit.
[] Press VCR-*.
• "VCR-*" lights up on the unit.
NOTES:
• Be sure to engage tile DVD deck in stop rnode.
• It is not possible to perform the above steps when the DVD deck is in
timer standby mode.
50 ENOPERATIONS
ON VCR DECK
| BasicRecording
| Recording
Features
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TVlCABLEIDBSlDVD switch to DVD.
[email protected]
•
•
•
•
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Press VCR/DVD repeatedly so that the VCR lamp lights up on the
unit.
.JVC
'
V(R/DVD
m
i
O
RE(MODE (H +/=
V(R/DVD--
[email protected]/DVD---0=9
CANCEL
RE(MODE
_
--
||
--
(N +/=
--DISPLAY
_
W/V(R_
-- (H +/=
JVC
1 Load a cassette with the record safety tab intact.
• The unit's power comes on automatically and the counter is reset to
0:00:00.
2 Press VCR/DVD repeatedly so that the VCR lamp lights up on
the unit.
3 Press CH +/- or the number
wish to record.
4
keys to select the channel you
Press REC MODE repeatedly to set the recording mode.
5 Press • on the unit to start recording. Or press and hold • and
press I_ on the remote control.
• The VCR recording lamp lights up on the unit.
6 Press II to pause recording.
• You can select channel during the Record Pause mode.
• To resume recording, press I_.
7 Press • to stop recording.
• The VCR recording lamp lights off on the unit.
WatchAnotherProgramWhile RecordingOn TheUnit
While recording is going on, you can watch another program on the
TV by using the TV's tuner.
NOTE:
It is required that the remote control is set to be able to operate tile TV
in advance. (y" pg. 70)
1 During recording, press TV/VCR to select TV mode if your unit
is connected to the TV via the RF connection.
• VCR mode is disengaged, then the VCR indicator lights off and "TV"
appears on the front display panel.
7
I
VCR indicator lights off.
RecordingResumeFunction
• The program received on the TV's tuner is displayed on the TV
screen.
If there is a power outage during recording, Instant Timer
Recording or timer recording (_ -" pg. 50, 52, 53), the recording will
resume automatically when power is restored to the unit unless the
unit's memory backup has expired.
2 Slide the TV/CABLE/DBS/DVD
switch to TV.
3 Press CH +/- repeatedly to select the desired channel.
OPERATIONS ON VCRDECK
E. 51
InstantTimerRecording
(ITR)
SecondAudioRecording
This easy method lets you record
(selectable
in 30-min. increments),
recording
is finished.
This unit's built-in MTS decoder
enables
reception
of Multichannel
TV Sound broadcast.
To record a SAP program
received,
set "2ND
AUDIO RECORD"
to "ON". (: =" pg. 76)
1 Press
•
on the unit to start
for from 30 minutes to 6 hours
and shuts the unit off after
NOTE:
recording.
2 Press • again to engage the ITR mode.
• On the front display panel, "0:30" appears.
3
If you want
extend
to record
the time. Each
for more
press
than
extends
30 minutes,
recording
press
• to
time by 30 minutes.
NOTES:
• You can only perform ITR using the • button on the unit.
• When the end of the tape is reached during timer recording or Instant
Timer Recording, the cassette is automatically
ejected and the unit is
shut off.
• During Instant Timer Recording, any other timer programed recording
won't start even if their start time has come. In such a case, the timer
programed recording starts (if the end time of the timer programed
recording is set after the end of Instant Timer Recording) after the
Instant Timer Recording finishes.
ElapsedRecordingTimeIndication
1
Press DISPLAY
display panel.
until a counter
2
to reset
Press
CANCEL
reading
the counter
Accidental
erasure prevention
To prevent accidental recording
oil a recorded cassette, remove
its safety tab. To record on it
later, cover the hole with
adhesive tape.
Record safety tab
appears
before
When the channel is changed on the unit;
• The "STEREO"
indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
• The "SAP" indicator appears on the screen for about 5 seconds if the
program is a SAP broadcast.
• Both indicators appear when a stereo program is accompanied
by
SAP sound.
on the front
starting
recording
or
playback.
• The counter is reset to "0:00:00" and shows the exact elapsed time
as the tape runs. You can check the exact time of a recording or
playback.
TapeRemainingTime
1
Press DISPLAY
until the time remaining
oil the tape appears.
• By pressing the DISPLAY button, you can change display to show
the clock time, counter reading or tape remaining time.
NOTES:
• When you press DISPLAY, the on-screen display appears ell the TV
screen for 5 seconds, then the displays other than the counter
disappears. To clear the counter display, press DISPLAY.
• Depending on the type of tape being used, the tape remaining time
reading may not appear right away, or is not correct.
"- -:- -" may sometimes
appear, or the display may blink on
occasion.
52 ENOPERATIONS
ON VCR DECK
| VCRPlus+®TimerPrograming
6 Press REC MODE to select the desired recording mode. Or
press _ _ to select "SP/EP", then press/\V
to select the desired
recording mode.
You can program this unit to timer-record as many as 8 programs.
With the VCR Plus+ system, timer programing is greatly simplified
because each TV program has a corresponding code number
which your unit is able to recognize.
You can use the remote control to enter the PlusCode number.
7 Press ENTER to complete timer programing.
• To program another timer, repeat steps 3 - 7.
• If "PROGRAM NOT COMPLETED PROGRAM OVERLAP" appears
on the TV screen, see page 54.
•
•
•
•
Make sure that the unit's built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the "rV/CABLE/DBS/DVD switch to DVD.
8 Press VCR TIMER (®) to engage the unit's timer mode. The
VCR timer lamp lights up on the unit and the DVD deck is
automatically selected. When the DVD deck is in timer standby
mode, the unit is automatically turned off.
• To disengage the timer mode, press VCR TIMER (®) again.
IMPORTANT:
If you have moved to a different area or if a broadcasting
station's
channel number has been changed, the wrong channel number will
be displayed on the VCR Plus+ program screen in step 5. When this
happens, set the correct Guide Channel number for that station.
(_" pg. 77, "Changing
VCR Plus+ _ Setting")
_U=9
(AN(EL
VCRPLUS+
ENTER--
NOTES:
• To Timer-Record Weekly Or Daily Serials:
-- in step 5, press number key "9" for weekly serials or number key
"8" for daily serials (Monday -- Friday). Either "WEEKLY" or "DAILY"
appears on the TV screen. Pressing the button again makes the
corresponding indication disappear.
• You can program this unit to timer-record as many as 8 programs. If
you try to program the unit to record a ninth, "PROGRAM FULt_'
appears on the TV screen and "FULt_' appears on the front display
panel. To record the extra program, you must first cancel any
unnecessary programs. (_ 7,pg. 54)
• To record the programs received by cable box or DBS receiver,
record on the DVD discs. For details, refer to "VCR Plus+ ° Timer
Programing" (,:" pg. 41).
_RETURN
[email protected]_
JVC
1 Load a cassette with the record safety tab intact.
2 Press VCR/DVD repeatedly so that the VCR lamp lights up on
the unit.
3 Press VCR PLUS+ to access the VCR Plus+ screen.
4 Press the number keys to enter the
PlusCode number of a program you
PLUSCODE
wish to record, then press ENTER.
• If you have made a mistake, press
CANCEL and input the correct number
before you press ENTER
• If the number you entered is invalid,
"ERROR" appears on the TV screen and vc£ PLUS+
SYSTEM
"Err" appears on the front display panel.
Press CANCEL and input a valid PlusCode number.
5 The PlusCode number you entered
and the matching timer-recording
information are displayed on the TV
screen. Check the program data.
• To cancel this setting, press VCR
PLUS+ or PROG/CNECK
NO.
PRU_RA_
1
PLUSSODE
N0.12345678)
START
STOP
IMPORTANT:
Make sure tile channel position number you wish to record is
displayed; if not, see "Changing
VCR Plus+ _ Setting" (2" pg. 77) and
set the Guide Channel number correctly.
OPERATIONS
You can program this unit to timer-record as many as 8 programs.
If you do not know the PlusCode number for the program you wish
to record, use the following procedure to set your unit to
timer-record the program.
1 0 Press ENTER to access the Program Check screen.
1 1 Press PROG/OHECK to complete timer programing.
"PROGRAM COMPLETED" appears on the TV screen for about 5
seconds, then the normal screen appears. If "PROGRAM NOT
COMPLETED PROGRAM OVERLAP" appears on the TV screen,
see page 54.
• To program another timer, repeat steps 3 - 11.
Make sure that the unit's built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TVlCABLEIDBSlDVD switch to DVD.
1 2 Press VCR TIMER (®) to engage the unit's timer mode. The
VCR timer lamp lights up on the unit and the DVD deck is
automatically selected. When the DVD deck is in timer standby
mode, the unit is automatically turned off.
• To disengage the timer mode, press VCR TIMER (®) again.
V(R TIMER
{®} [email protected]/DVD -!CTb
dq_
CTb
NOTES:
• To Timer-Record Weekly Or Daily Serials:
-- anytime during steps 7 through 9, press number key "9" for
weekly serials or number key "8" for daily serials (Monday - Friday).
Either "WEEKLY" or "DALLY" appears on the TV screen. Pressing the
button again makes the corresponding indication disappear.
• You can program this unit to timer-record as many as 8 programs. If
you try to program the unit to record a ninth, "PROGRAM FULt_'
appears on the TV screen. To record the extra program, you must
first cancel any unnecessary programs. (_ pg. 54)
• In case of a power failure after programing, the unit's memory backup
keeps your selections for approximately 5 seconds.
• Programs that start after midnight must have the next day's date.
• To record the programs received by cable box or DBS receiver,
record on the DVD discs. For details, refer to "Manual Timer
Programing" (.:" pg. 42).
_0=9
PROG/(HE(:K
.......
ENTER-, l_)
(_
II_:/
I;q
RE( MODE_
jVr_
1 Load a cassette with the record safety tab intact,
2 Press VCR/DVD repeatedly so that the VCR lamp lights up on
the unit.
3 Press
PROG/CHECK
Program Check screen.
4
to access the
PR START STOP
I1
8:OOP 10:00
CH
12
DATE
12/24 I
/2
40
12/25
IO:OOA
Press Z\V to select the blank
number, then press ENTER. The
program screen appears.
5 Press 4 P*to select "START", then
press Z\V to set the desired start time.
• Each press of/\'J advances/goes back
the start time in 1-min. increments.
• To advance/go back the start time in 30min. increments, press and hold/','J.
10:45
PROGRAN 4
START
STOP
DATE
Press _ b. to select "STOP", then press/\V
to set the desired
stop time.
• Each press of/"_; advances/goes back the stop time in 1-min.
increments.
• To advance/go back the stop time in 30-min. increments, press and
hold Z_,'7.
7 Press _ b" to select "DATE", then press/\V
to set the desired
date.
• The current date appears on the TV screen. The date you enter
appears in its place.
8 Press _ b" to select "CH", then press/\V
channel.
EN 53
9 Press REC MODE to select the desired recording mode. Or
press 4 _ to select "SP/EP", then press/\V
to select the desired
recording mode.
| ManualTimerPrograming
•
•
•
•
ON VCR DECK
to select the desired
I
54 ENOPERATIONS
ON VCR DECK
WhenProgramsOverlapEachOther
If "PROGRAM NOT COMPLETED PROGRAM OVERLAP"
appears, you have another program overlapping the program you
have just made.
The Program Check screen appears and conflicting programs will
start blinking.
VCRTIMER
(e)
VCR/_VD--
CT3
CTJ
CTj
CT;Q c_ J
(TZJ
G_ZJ (gO
CANCEL _Z)
PROG/@IECK
..........
Cs3
%,=o/I
C_6Z3 Cr Z3
fl
EHY[R--
PROGRAM NOT COMPLETED
PR START STOP
O:OOP 10:00
1"2
IO:OOA 10:45
CH
12
DATE _.
12/24 1
40
12/25," /
PROGRAM OVERLAP
Example: Program 1 (you have just made) and Program 4
overlap each other.
1 Confirm the overlapping programs. Overlapping
on the TV screen.
2 Press/\V
to select the program to modify, then press ENTER
or b*.
• You can only select one of the overlapping programs.
Check,canceland changeprograms
1 When the VCR timer lamp lights on the unit
Press VCR TIMER (®), then press _b/l.
When the VCR lamp does not light up on the unit
Press VCR/DVD repeatedly so that the VCR lamp lights up on the
unit.
2 Press PROG/CHECK
to access the
Program Check screen.
PR START STOP
1
O:OOP 10:00
12
IO:OOA
Ii
11:30P
CH
12
DATE
12/24
40
12/25
1:00 125
12/25
10:45
To cancel a program
Press CANCEL to cancel a program.
3 Press/\V
to select the program,
then press ENTER. The program
screen appears.
4 Change the settings of the desired
recording options as required.
• Refer to steps 7 - t0 in "Manual Timer
Programing" (: , pg. 53).
programs blink
PROGRAM 4
START
DATE
ERI
STOP
im_s_P
Press PROG/CRECK to complete
timer correction. The previous screen resumes.
Press VCR TIMER (®).
• The VCR timer lamp lights up on the unit and the DVD deck is
automatically
selected. When the DVD deck is in timer standby mode,
the unit is automatically
turned off.
NOTE:
If you do not mind this overlap, press PROG/CHECK to finish the tirner
program setting. The program with the lower program number will be
recorded and the other one will not be recorded correctly. If no changes
are made for approximately 1 minute, the unit will return to the normal
screen.
3 Press/\V
to select the desired program to be cancelled or
changed.
To cancel the program
Press CANCEL.
• "PROGRAM COMPLETED" appears on the TV screen for about 5
seconds, then the normal screen resumes.
To change the program setting
Press ENTER, then go to step 4.
4 Change the program setting.
• Refer to steps 7 - 10 in "Manual Timer Programing" (: • pg. 53).
Press PROG/CHECK
to check if the conflict has been settled.
Program check screen appears.
• "PROGRAM COMPLETED" appears on the TV screen for about 5
seconds, then the normal screen resumes.
Press VCR TIMER (®).
NOTE:
When ally overlaps remain after deletion and modification of programs,
Program Check screen remains showing the conflicting programs. In
such a case, repeat the procedure above until the conflict is solved.
NAVIGATION (DVD DECK ONLY)
| LibraryDatabaseDVDNavi
The Library Database DVD Navi enables you to search and select
the desired programs recorded on a DVD-RAM/R/RW disc very
easily.
You can record up to 99 programs on a disc.
Each time a program is recorded on the disc, the information of the
program is registered for the Library Database DVD Navi
automatically.
So, you can confirm the information of the programs recorded oil
the disc with the Library Database DVD Navi screen. And, you can
also select one of the programs recorded on the disc using the
Library Database DVD Navi.
The following screen appears as the Library Database DVD Navi
screen when you press NAVIGATION. You can move the arrow to
select the desired position on the screen by pressing/\_
_ b. on
the remote control.
[]
[]
[]
[]
[]
[]
[]
[]
EN
55
Using Library Database DVD Navi system, you can easily modify
registered information, edit the program or play list, as well as
search for the beginning of each program.
About registration of information
The following information is automatically registered for each
program when ordinary recording or timer recording is performed,
then stored in an area specified on the unit.
• index* (reduced still pictures to show program titles)
• program title*
• category*
• date and time
• channel
• recording mode
• length of recording time
The items marked with an asterisk (*) can be easily modified and
registered again after recording by using Library Database DVD
Navi system.
About editing of programs
Library Database DVD Navi system has the following functions for
editing of programs.
• "Modify Play List Information" (7. pg. 58)
• "Delete Program" (: , pg. 57)
The limitations of registration
You can register information up to 99 programs.
When the amount of information is at the limits of registration, you
cannot record new program any more. In this case, you need to
delete old programs to register new one. (: ="pg. 57)
NOTE:
Once a DVD-R/RW (Video mode) disc has been finalized, the displays
for original and play list do not appear. Only display for library appears.
sJ
Index
(Small still picture of each program)
Names of functions
ORIGINAL (_ _ pg. 56)
PLAY LIST (_" pg. 58)
LIBRARY (: • pg. 60)
Remaining time
(Based on the recording mode currently selected)
Current/Total number of program(s)
(For example, there are 6 recorded programs and the program
indicated by the arrow is the 3rd one.)
Icons
(Indicate the recording situation for each program.)
Recording information for the program indicated by the arrow
Guidance for operations
Operational commands
The Icons and their meanings
This program is write-protected.
[]
This program has stereo sounds.
This program was recorded with timer recording.
The display
recording
for original
The display
for play list
56
EN NAVIGATION (DVD DECKONLY)
ScanForBeginning(s)
Of Program(s)
| ModifyOriginalInformation
]
•o Turn
Slide on
thethe
TVlCABLEIDBSIDVD
switch
to DVD.
TV and select the video
channel
(or AV mode).
1
I
• Turn on the TV and select the video channel (or AV mode).
• Slide the TV/CABLE/DBS/DVD switch to DVD.
CTJ
CT3
CTJ
MEMO
--
[;
--0=9
"-- SELECT
[]
CLEAR
--
NAVI6ATION=
_,o,.,.||
EN'fER"_
Jvc
You can scan the beginning of the program easily with the Library
Database DVD Navi.
1 Load a recorded disc.
Press NAVIGATION.
appears.
3 Press/\V
The Library Database
DVD Navi screen
4 _ to select
"ORIGINALS', then press ENTER.
4
Press *q L>to select the index
(small still pictures) of the desired
program.
• When you want the plural
programs to be played back
continuously, press MEMO after
selecting the desired program.
The numbers of the playback
order appear on the index. You
can select up to 30 programs.
• When you want to correct the order, move the arrow to the desired
index and press MEMO. The number disappears and the unit renumbers the other programs automatically.
• When you want to cancel the order, press CLEAR (•).
Press ENTER or SELECT (1_) to start playback. The playback
starts.
Press II to pause playback.
• To resume normal playback, press I_.
Press • to stop playback.
Modify Index
1 PressNAVIGATION. The Library Database DVD Navi screen
appears.
Press /\V _ P>to select "ORIGINAIJ', then press ENTER.
3 Press /\V _ L'-.to select one program you want to modify, then
press V.
4 Press /\V _ P-.to select "MODIFY", then press ENTER.
5 Press 4 b* to select "MODIFY INDEX".
Search for the picture from the
program by pressing the
appropriate buttons (4141, I_,
1_1_, or II). The pictures of the
program appear on the left
window.
7 Confirm the arrow is on
"REPLACE", then press ENTER to
register new index. New index
appears on the right window.
• When you press ENTER with the arrow on "RETURN" you can return
to the previous screen.
8 Press NAVIGATION to return to the normal screen.
• Press • to cancel pause mode after pressing NAVIGATION.
NAVIGATION (DVD DECK ONLY)
EN
57
Modify ProgramName
DeleteProgram
1 Perform steps 1 to 3 of "Modify Index" (__"pg. 56) before
continuing.
You cannot record any more with Library Database DVD Navi once
the registered programs on the disc reach 99 programs. Deleting
unnecessary programs after dubbing or other operations can
increase remaining time and available recording capacity. (For
DVD-R discs, although it is possible to delete recorded programs,
available recording capacity does not increase.) The deleted
program is never resumed. Play lists and program information in
the unit's library are also deleted.
2 Press/\V
_ _ to select "MODIFY", then press ENTER.
3 Press 4 b" to select "MODIFY
4
Press/\_
NAME".
_ L>to select the
desired letter or command, then
press ENTER. Repeat this
process to complete the name.
• To correct a letter, press/','_' -" I:
to select "DELETE" or "DELETE
ALE', then press ENTER.
• You can enter the letters up to 64.
• You can also enter the new name
with the number keys. For example, when you press 2 repeatedly,
"A", "B", "C", "a", "b", "c", "2", and then "A" appear by turns. You can
use the following buttons.
Number keys: for entering letters, numbers and blank space
_ buttons: for moving the entering or inserting point
CLEAR (11) button: for correcting a letter
1-41.<1/1_,-I_1
buttons: for changing character tables
5 Press/\V
1 Perform steps 1 to 2 of "Modify Index" (: _ pg. 56) before
continuing.
Press J\V 4 P>to select one program you want to delete, then
press V.
3 Press J\V 4 b. to select "DELETE", then press ENTER. The
message appears for your confirmation.
4 Press 4 b_ to select "YES", then press ENTER.
• When you cancel the deletion, select "NO", then press ENTER.
5 Press NAVIGATION to return to the normal screen.
DeleteUnwantedPart Of TheProgram
You can delete unwanted part of the program.
4 _ to select "SAVE", then press ENTER.
6 Press/\V
4 _ to select "RETURN", then press ENTER. The
Library Database DVD Navi screen appears again.
7 Press NAVIGATION to return to the normal screen.
1 Perform steps 1 to 2 of "Modify Index" (3. pg. 56) before
continuing.
Press 4 b> to select one program whose unwanted part you
want to delete, then press V.
3 Press 4 [_>to select "EDITING", then press ENTER.
Modify Category
4 Press I_ to start playback. The playback pictures appear in the
window on the screen. The elapsed playing time starts counting
with the arrow on "IN".
1 Perform steps 1 to 3 of "Modify Index" (3. pg. 56) before
continuing.
2 Press/\V
5 Find the point where you want
4 _ to select "MODIFY", then press ENTER.
3 Press 4 b. to select "MODIFY CATEGORY".
4
Press/\V
_ I.>to select the
desired category, then press
ENTER.
.....
_
A
:-._
6 Find the point where you want
the deletion to end, then press
ENTER with the arrow on "OUT".
The edit-out time is fixed.
• Press _1_1, I_, I_,
I_1_1,1_I_1or II to find the edit-in and edit-out
points.
5 Press ENTER. The Library
Database DVD Navi screen
appears again.
6 Press NAVIGATION
to the normal screen.
_-_r s_,
the deletion to begin, then press
ENTER with the arrow on "IN".
The edit-in time is fixed and the
elapsed playing time starts
counting again.
to return
ProtectTitle
7 Press/\_
4 b>to select "PREVIEW",
preview the edited program.
You can protect the program to prevent accidental erasure of the
important program.
8 Press/\_
4 b. to select "EXECUTE", then press ENTER.
• If you do not want to delete the scene, select "CLEAR" and press
ENTER.
1 Perform steps 1 to 2 of "Modify Index" (_" pg. 56) before
continuing.
2 Press/\V
press V.
_ I.>to select a program you want to protect, then
3 Press _ [> to select "PROTECT", then press ENTER. "_"
appears.
• To cancel the protection, repeat 2 - 3 again.
4 Press NAVIGATION to return to the normal screen.
'4 "
NOTE:
All the programs on a disc will be deleted once the disc is formatted
even if they are protected titles. (: _ pg. 57)
then press ENTER to
Press 4 b> to select "YES", then press ENTER. The selected
scene is deleted.
• To cancel the deletion, press
L. to select "NO", then press ENTER.
To modify the points
[] Press 4 b>to select "CLEAR", then press ENTER.
[] Repeat steps 4 - 9 as necessary.
1 O Press NAVIGATION to return to the normal screen.
NOTES:
• There may be a discrepancy
of several seconds between tile scene
you intend to edit, and the scene which is actually edited.
• Available recording capacity may not match the deleted part after
deletion.
58
EN
NAVIGATION (DVD DECKONLY)
| ModifyPlayListInformation
•o Turn
Slide on
thethe
TV/CABLE/DBS/DVD
TV and select the video
switch
channel
to DVD.
(or AV mode).
0=9
MEMO
NAVIGATION
--
EHTER_"
t:
] 1;;
..............
ELEcT
m-CLEAR
_r _
..... ||
]
8 Press _ P*to select "PREVIEW",
the play list.
then press ENTER to preview
9 Press q b_ to select "EXECUTE",
list is created.
then press ENTER. The play
To modify the points
[] Press q L>to select "CLEAR", then press ENTER.
[] Repeat steps 5 - 9 as necessary.
1 0 Press NAVIGATION to return to the normal screen.
NOTES:
• There may be a discrepancy
of several seconds between the scene
you intend to edit, and the scene which is actually edited.
• The title, index and category of the play list can be modified in the
same way as "ORIGINAU'.
(7- pg. 56)
• You can modify the play list that has just been created here by
adding, moving, or deleting unwanted parts to create a digest edition,
etc.
AddScenesToA PlayList
1 Perform steps 1 to 3 of "Create Play List" (y
continuing.
pg. 58) before
2 Press 4 b> to select the play list to which you wish to add a
scene, then press V.
Q_QQ
3 Press
_ b. to select "EDITING", then press ENTER.
4
Press q b_ to select "ADD
SCENE".
Jvc
Play List
It is a collection of the scenes. A play list can be freely edited and
played back without ever changing any original recording data.
Using the random access of a DVD disc (which allows video data
to be instantly read no matter where it is on the disc), a play list
includes information such as the timer counter for the playback
start point and end point, indexes for checking the contents of
recorded data, category information, and more. Playback
according to a play list you have created allows you to enjoy
various combinations of video images from a single program.
CreatePlay List
1 Load a DVD-RAM or DVD-RW (VR mode) disc that was
recorded with this unit.
2 Press NAVIGATION.
appears.
The Library Database
DVD Navi screen
3 Press/\V
_ _ to select "PLAY LIST", then press V or ENTER.
4
q L>to select "CREATE", then press ENTER.
Press/\_;
5 Press I_ to
window on the
with the arrow
• To locate the
start playback. The playback pictures appear in the
screen. The elapsed playing time starts counting
on "IN".
beginning of other titles press I<_l/l_.-I.
6 Find the point where you want
the created play list to begin, then
press ENTER with the arrow on
"IN". The edit-in time is fixed and
the elapsed playing time starts
counting again.
7 Find the point where you want
the created play list to end, then
press ENTER with the arrow on
"OUT". The edit-out time is fixed.
• Press 41_1, I_, I_,
I<_1, 1_I_.-Ior II to find the edit-in and edit-out
points.
• The edit-out point must come after the edit-in point.
5 Press I_ to start playback. The
playback pictures appear in the
window on the screen. The
elapsed playing time starts
counting with the arrow on "IN".
• To locate the beginning of other
titles, press I<<l/l_t_l.
6 Find the point where you want the added scene to begin, then
press ENTER with the arrow on "IN". The edit-in time is fixed and
the elapsed playing time starts counting again.
7 Find the point where you want the added scene to end, then
press ENTER with the arrow on "OUT". The edit-out time is fixed.
• Press 41_1, I_, I_,
I<_l, 1_I_1or II to find the edit-in and edit-out
points.
8 Press 4 L>to select "PREVIEW", then press ENTER to preview
approximately 5 seconds before and after the edited scene.
9
Press 4 b> to select "EXECUTE",
selected scene is added.
then press ENTER. The
To modify the points
[] Press _ P>to select "CLEAR", then press ENTER.
[] Repeat steps 5 - 8 as necessary.
1 0 Press NAVIGATION to return to the normal screen.
NOTE:
There may be a discrepancy of several seconds between the scene you
intend to edit, and the scene which is actually edited.
Move Scenes
1 Perform steps 1 to 3 of "Create Play List" (_" pg. 58) before
continuing.
2 Press _ L> to select a play list into which you wish to move a
scene, then press _.
3 Press
_ b> to select "EDITING", then press ENTER.
4 Press q b" to select "MOVE
SCENE".
5 Press I_ to start playback. The
playback pictures appear in the
window on the screen. The
elapsed playing time starts
counting with the arrow on "IN".
• To locate the beginning of other
titles, press I<_l/l_,-I.
...............
NAVIGATION (DVD DECK ONLY)
6
Play BackPlay List
7 Find the point where you want the moved scene to end, then
press ENTER with the arrow on "OUT". The edit-out time is fixed.
1 Perform steps 1 to 3 of "Create Play List" (
continuing.
2 Press 4 b* to select the index
Find the point where you want the moved scene to begin, then
press ENTER with the arrow on "IN". The editqn time is fixed and
the elapsed playing time starts counting again.
8 Press I_ to start playback.
9 Find the point where you want the moved scene to be moved,
then press ENTER with the arrow on "MOVE TO".
• Press 41_1, I_, I_,
I_1_1,l,,-m.-Ior II to find the edit-in, edit-out and
move-to points.
1 O Press 4 [->to select "PREVIEW" then press ENTER to
preview the part approximately 5 seconds before and after the
point to which the scene has been moved.
1 1 Press 4 b. to select "EXECUTE",
selected scene is moved.
then press ENTER. The
To modify the points
[] Press _ [->to select "CLEAR", then press ENTER.
[] Repeat steps 5 - 11 as necessary.
1 2 Press NAVIGATION
to return to the normal screen.
1 Perform steps 1 to 3 of "Create Play List" ( " pg. 58) before
continuing.
2 Press 4 b, to select a play list from which you wish to delete
unwanted parts, then press V.
3 Press _ b, to select "EDITING", then press ENTER.
(small still pictures) of the desired
play list.
• When you want the plural play lists
to be played back continuously,
press MEMO after selecting the
desired play lists. The numbers of
the playback order appear on the
index. You can select up to 30 play
lists.
• When you want to correct the order, move the arrow on the desired
index and press MEMO. The number disappears and the unit renumbers the other play lists automatically.
• When you want to cancel the order, press CLEAR (m).
4 Press II to pause playback.
• To resume normal playback, press I_.
5 Press • to stop playback.
1 Perform steps 1 to 3 of "Create Play List" (_ _"pg. 58) before
continuing.
2 Press 4 b. to select one play list you want to delete, then press
V.
3 Press 4 b. to select "DELETE", then press ENTER.
4 Press 4 b. to select "YES", then press ENTER.
• When you cancel the deletion, select "NO", then press ENTER.
5 Press NAVIGATION to return to the normal screen.
4 Press _ L>to select "DELETE
SCENE", then press ENTER.
5 Press I_ to start playback. The
,_,_£_
_/
E!:_
.............
;-_ N
playback pictures appear in the
window on the screen. The
elapsed playing time starts
_
''_
:_
..........
NOTE:
Even if a play list is deleted, the programs recorded on a DVD disc and
the library information are not affected at all.
Modify Index
counting with the arrow on "IN".
• To locate the beginning of other
titles, press I_l_l/l=-m.-I.
6 Find the point where you want the deletion to begin, then press
ENTER with the arrow on "IN'. The edit-in time is fixed and the
elapsed playing time starts counting again.
7 Find the point where you want the deletion to end, then press
ENTER with the arrow on "OUT". The edit-out time is fixed.
• Press 41_1, I_, I_1_, I<1<1,l_l_l or II to find the edit-in and edit-out
points,
8 Press 4 b" to select "PREVIEW", then press ENTER to preview
the scene approximately 5 seconds before and after the deleted
part.
then press ENTER. The
To modify the points
[] Press 4 b> to select "CLEAR", then press ENTER.
[] Repeat steps 5 - 9.
1 O Press NAVIGATION
"pg. 58) before
DeletePlay Ust
DeleteUnwantedPart FromPlay List
9 Press 4 b>to select "EXECUTE",
selected scene is deleted.
59
3 Press ENTER or SELECT (1_) to start playback. The playback
starts.
NOTE:
There may be a discrepancy of several seconds between tile scene you
intend to edit, and the scene which is actually edited.
_
EN
to return to the normal screen.
NOTE:
There may be a discrepancy of several seconds between the scene you
intend to edit, and the scene which is actually edited.
[] Perform steps 1 to 3 of "Create Play List" (y" pg. 58) before
continuing.
[] Perform steps 3 to 8 of "Modify Index" (:_" pg. 56).
Modify ProgramTitle
[] Perform steps 1 to 3 of "Create Play List" (_ _"pg. 58) before
continuing.
[] Press/\V
_ b_ to select one program you want to modify, then
press V.
[] Perform steps 2 to 7 of "Modify Program Name" ( "pg. 57).
ModifyCategory
[] Perform steps 1 to 3 of "Create Play List" ( •pg. 58) before
continuing.
[] Press/\_
_ b. to select one program you want to modify, then
press _.
[] Perform steps 2 to 6 of "Modify Category" ( " pg. 57).
60
EN NAVIGATION (DVD DECKONLY)
I ModifyLibraryInformation
RegisterDisc
1 Load a disc you want to register.
Press NAVIGATION.
appears.
Program information can be registered in the unit's memory for up
to 1,300 programs. It is helpful when finding out on which disc the
desired program is recorded.
•o Turn
Slide on
thethe
TV/CABLE/DBS/DVD
switch
to DVD.
TV and select the video
channel
(or AV mode).
3 Press/\V
The Library Database DVD Navi screen
_ P>to select "LIBRARY",
then press ENTER.
4 Press _ L;. to select "REGISTER",
then press ENTER.
5 Press _ L;.to select "REGISTER",
the registration.
then press ENTER to confirm
6 Press NAVIGATION
to return to the normal screen.
NOTES:
r_7_
C_3
• It is not possible to register discs
(: , pg. 43)
• It is not possible to register discs
JVC's DVD recorders.
• It is not possible to register discs
JVC's DVD recorders.
• It is not possible to register discs
'<OFF". (,::s pg. 74)
C_3
--
_,'cT:t]
1)
used for On-Disc
formatted
recorded
Tirner
on devices
on devices
Programing.
other than
other than
when "SAVE AS LIBRARY"
is set to
DeleteInformation
1 Press NAVIGATION.
appears.
The Library Database DVD Navi screen
Press J\V 4 b, to select "LIBRARY",
then press ENTER.
3 Press J\V 4 b, to select the appropriate
information, then press ENTER.
sort button to sort the
4 Press 4 b, to select a program you want to delete, then
press V.
Jvc
Press J\V 4 b, to select "DELETE", then press ENTER.
6 Press 4 P* to select "DELETE", then press ENTER to confirm
the deletion.
ScanForProgramFromLibrary
1 Press NAVIGATION.
appears.
2 Press/\V
The Library Database
_ L>to select "LIBRARY",
DVD Navi screen
then press ENTER.
3 Press _ [> to select the
appropriate sort button to sort the
information, then press ENTER.
"DISC No." : Sort by disc number
"CATEGORY" : Sort by category
"DATE" : Sort by date
....
"NAME" : Sort by name
• The sorting order can be switched
between ascending order and
descending order by pressing the sort buttons.
4
Press _ L>to select the desired program, then press ENTER.
• Playback begins automatically after the selected program is located.
When the disc that contains the selected program is not
loaded
A screen prompting you to load the designated disc appears. Place
the disc whose number is displayed on the screen after pressing
ENTER to close the prompt screen. Then perform steps 1 to 4.
NOTE-"
If a disc registered in the library is recorded or modified on DVD units
from other manufacturers, it may become impossible to operate
properly.
7 Press NAVIGATION
to return to the normal screen.
NAVIGATION
(DVD DECK ONLY) EN
61
4 Press _ P>to select the desired
| PlaybackWith MP3/JPEGNavigation
group, then press ENTER.
For MP3 Playback
• The tracks in the selected group
appear.
This unit can play back discs that MP3 sound files and JPEG
image files taken with digital still cameras or other devices are
recorded.
The MP3/JPEG Navigation enables you to search and select the
desired files recorded on CD-R/RW or CD-ROM discs very easily.
The following screen appears as the MP3/JPEG Navigation screen
when you press NAVIGATION. You can move the arrow to select
the desired position on the screen by pressing/\V
*_}L> on the
remote control.
For JPEG Playback
• The images in the selected group
appear.
Press/\V
_ b>to select the
desired item, then press ENTER.
The unit starts playback from the
selected item.
• The unit stops when all items in
the selected group are played
back.
NOTES:
• If you press SELECT (1_) instead
of ENTER in step 4, the unit starts playback from the first file of the
group.
• JPEG files are played back as a slide show at the set intervals.
(: , pg. 36)
• If a file name includes any 2-byte character, the unit may not show
the file name correctly.
• Press/\'J to select "RETURN", then press ENTER to return to the
screen that shows the group(s).
• The order of the groups and items shown in steps 4 and 5 may differ
from the order shown on your PC.
ProgramPlayback
1 Perform steps 1 to 4 of "Locating The Desired Group And
Tracks" in the left column before continuing.
Press/XV 4 b>to select the desired item, then press MEMO in
the desired order.
• The order number appears on the left of the track name.
• Repeat this step as necessary.
• To cancel the track, press
i I:. to select the track, then press
CANCEL.
• Pressing CLEAR (m) clears all the order numbers.
[]
[]
[]
[]
[]
[]
[]
Name of the inserted disc.
Sort buttons ("MP3'_ "JPEG")
Selected group number/total number of groups on the disc
Group name
Return button ("RETURN")
Group name/Created date
File type indicator
_:
MP3
_:
JPEG
[]
[]
Selected
Selected
contains
Program
[]
file
file number/total number of files in the group that
the selected file
number/file name
LocatingTheDesiredGroupAndTracks
1 Lead a disc.
2 Press NAVIGATION.
appears.
The MP3/JPEG Navigation screen
3 For MP3 Playback
Press _ b. to select "MP3". Only groups which contain MP3 files
appear.
For JPEG Playback
Press _ b. to select "JPEG". Only groups which contain JPEG files
appear.
3 Press I_ to start playback.
• To quit the Program Playback, press !
• Repeat playback can be performed if it is set as such on the onscreen bar. (_" pg. 34)
NOTES:
• It is nat possible to select tracks and images simultaneously.
• It is net possible to select tracks or images in other groups.
On completion
of the playback of all the items
[] Perform steps 1 to 4 of "Locating The Desired Group And
Tracks" in the left column.
[] Press CLEAR (m).
• The order numbers are reset and cleared.
[] Press NAVIGATION to complete the procedure.
62 EN EDITING
| TapeDubbing(FromVCRToDVD)
1 For DVD deck
Load a recordable disc.
For VCR deck
DubbingAn EntireCassette
Load a cassette you want to dub.
Because this unit includes both DVD deck and VCR deck, you can
easily use this unit for dubbing
without connecting
any other
2 Press VCR/DVD
the unit.
repeatedly so that the DVD lamp lights up on
3 Press REC MODE repeatedly to set the recording mode.
equipment.
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TV/CABLE/DBS/DVD
switch to DVD.
V(R --_
V<R/DVD
m
m_
CZ_
_D
C__-J
d__2J cC_J
_r _
RECMODE --
Jvc
CYD
DUggIN6
4 Press VCR-* to select the dubbing direction.
• "VCR_" lights up on the unit.
5 Press and hold DUBBING for more than 2 seconds to start
dubbing.
• If the tape has not been rewound, the VCR deck rewinds the tape
automatically. When the VCR deck has finished rewinding, dubbing
begins automatically.
• After dubbing is completed, the VCR deck rewinds the tape
automatically and the unit shuts off.
• To stop dubbing, press IN
NOTES:
• If you set the dubbing direction incorrectly, you could erase an
important recording that you wanted to dub. It is recommended to
conduct a test with unimportant cassettes first.
• The superimposed
indication during the operation or dubbing is not
recorded.
• It is not possible to dub a tape with a copy protection signal.
• If the recording capacity of disc become full, the tape stops
automatically.
• It is not possible to perform other operations like Live Memory
Playback. Check the recorded program on the disc after dubbing.
• Dubbing is not possible on the discs used exclusively for On-Disc
Timer Programing.
• If the index code is found on a tape, a single title is created. While
creating a title, the dubbing stops and then starts again.
• When dubbing can not be performed properly, set "BLUE BACK" to
"OFF'. (,:" pg. 76)
ED[TXNG
| ManualDubbing
(FromVCRToDVD)
E. 63
1 For DVD deck
Load a recordable disc.
For VCR deck
DubbingA Part Of A Cassette
Load a cassette you want to dub.
You can dub the selected scenes on a tape to the DVD disc,
starting and stepping wherever you wish.
2 Press VCR-* to select the dubbing direction.
• "VCR_" lights up on the front display panel.
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TVlCABLEIDBSlDVD switch to DVD.
3 Prepare the VCR deck for dubbing.
[] Press VCP,/DVD repeatedly so that the VCR lamp lights up on
the unit.
[] Locate the point from where you want to start dubbing, then
pause playback by pressing the following buttons: I_, 1_1_, _141,
I, II
4 Prepare the DVD deck for dubbing.
[] Press VCP,/DVD repeatedly so that the DVD lamp lights up on
the unit.
[] Press REC MODE repeatedly to set the recording mode.
[] Press and hold II, then press • so that the DVD deck enters
the Record Pause mode.
V(R/DVD
m
0_
#UBB_NG
Press and hold DUBBING for more than 2 seconds to start
dubbing.
Press • to stop recording on the DVD deck. Then press VCR/
DVD, and press • to stop playback on the VCR deck.
VCR/DVD-
CT_3 C_
C%_
--b'-
RE(NODE--
_
@
JV8
NOTES:
• If you set the dubbing direction incorrectly, you could erase an
important recording that you wanted to dub. It is recommended to
conduct a test with unimportant cassettes first.
• There may be a discrepancy of several seconds between where you
intend dubbing to start, and where it actually stars.
• The superimposed indication during the operation or dubbing is not
recorded.
• It is not possible to dub a tape with a copy protection signal.
• If the recording capacity of disc become full, the tape stops
automatically.
• It is not possible to perform other operations like Live Memory
Playback. Check the recorded program on the disc after dubbing.
• Dubbing is not possible on the discs used exclusively for On-Disc
Timer Programing.
• When dubbing can not be performed properly, set "BLUE BACK" to
"OFF".( "pg. 76)
64 EN EDITING
1
For DVD deck
| DiscDubbing(FromDVDToVCR)
Load a disc you want to dub.
For VCR deck
DubbingAn EntireDisc
Load a cassette with the record safety tab intact.
Because this unit includes both DVD deck and VCR deck, you can
easily use this unit for dubbing
without connecting
any other
2 Press VCR/DVD
the unit.
repeatedly so that the VCR lamp lights up on
3 Press REC MODE repeatedly to set the recording mode.
equipment.
4
Press ",-DVD to select the dubbing direction.
• "*-DVD" lights up on the unit.
5 Press and hold DUBBING for more than 2 seconds to start the
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TV/CABLE/DBS/DVD
switch to DVD.
DVD
V<R/DVD
m
DUBgING
VCR/DVD--
CT_J L'_b
CY_J
C__-J t___2J cCCJ
_PROGRBSIVE
SCAN
m--
RECMODE
Jvc
dubbing.
• If the tape has not been rewound, the VCR deck rewinds the tape
automatically. When the VCR deck has finished rewinding, dubbing
begins automatically.
• After dubbing is completed, the VCR deck rewinds the tape
automatically and the unit shuts off.
• To stop dubbing, press •.
NOTES:
• It is not possible to start dubbing if the unit retains a memory of the
resume points. Press • twice to clear the resume points.
• There may be a discrepancy of several seconds between where you
intend dubbing to start, and where it actually stars.
• The superimposed indication during the operation or dubbing is not
recorded.
• When the end of the tape is reached during dubbing, the tape is
ejected and both deck stops.
• When the progressive mode is set, "*-DVD" does not light up on the
front display panel. Press PROGRESSIVE SCAN so that video
output indicator ([_) lights off on the front display panel.
• It may be impossible to dub a DVD-R or DVD-RW (Video mode) disc
recorded on the devices from other manufacturers or on a PC. In
such case, perform "Manual Dubbing (From DVD To VCR)"
(_ pg. 65).
• It is not possible to perform other operations like Live Memory
Playback. Check the recorded program on the disc after dubbing.
• If "VCR_" lights up on the unit and you play back a DVD VIDEO disc,
the images dubbed to the VCR deck may not be output to the TV
properly.
EDITING
EN
65
1 For DVD deck
| ManualDubbing
(FromDVDToVCR)
Load a disc you want to dub.
For VCR deck
DubbingA PartOfA Disc
Load a cassette with the record safety tab intact.
You can dub the selected scenes on a tape to the DVD disc,
starting and stepping wherever you wish.
2 Press _-DVD to select the dubbing direction.
• "*-DVD" lights up on the front display panel.
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TVlCABLEIDBSlDVD switch to DVD.
3 Prepare the DVD deck for dubbing.
[] Press VCP,/DVD repeatedly so that the DVD lamp lights up on
the unit.
[] Locate the point from where you want to start dubbing, then
pause playback by pressing the following buttons: I_, 1_1_, _141,
I, II
4 Prepare the VCR deck for dubbing.
[] Press VCP,/DVD repeatedly so that the VCR lamp lights up on
the unit.
[] Press REC MODE repeatedly to set the recording mode.
[] Press and hold II, then press • so that the VCR deck enters
the Record Pause mode.
V<R/DVD
m
0 _
#UBBING
5 Press and hold DUBBING for more than 2 seconds to start the
dubbing.
6 Press • to stop recording on the VCR deck. Then press VCR/
DVD, and press • to stop playback on the DVD deck.
VCR/DVD-
PROGRE%IVE
S(AN
--
RE(NODE
_
_
_ _
JV8
--0
||
NOTES:
• It is not possible to start dubbing if the unit retains a memory of the
resume points. Press • twice to clear the resume points.
• There may be a discrepancy of several seconds between where you
intend dubbing to start, and where it actually stars.
• The superimposed indication during the operation or dubbing is not
recorded.
• When the end of the tape is reached during dubbing, the tape is
ejected and both deck stops.
• When the progressive mode is set, "*-DVD" does not light up on the
front display panel. Press PROGRESSIVE SCAN so that video
output indicator (_) lights off on the front display panel.
• It is not possible to perform other operations like Live Memory
Playback. Check the recorded program on the disc after dubbing.
66 ENEDITING
| DV Dubbing(DVDDeckOnly)
You can dub programs from a camcorder or DV equipment
connected to the unit with a DV cable. The unit's remote control
allows you the limited control of the connected camcorder or DV
equipment functions during dubbing.
NOTE:
When you connect a PC to tile DV IN connector,
the normal operation of this unit.
we do not assure
1 Connect a camcorder or DV equipment to the DV IN connector
on the unit's front panel.
2 Load a DVD-RAM/RW/R disc on the unit.
3 Press CH +/- to set the channel to "DV DUBBING".
• The "DV DUBBING" controller appears on the TV screen.
• If "t',_ I_" does not appear on the "DV DUBBING" controller, make
sure the DV equipment is connected correctly.
4 Press 4 b" to select
=_"},
5 Press/\V
to select the desired
then press ENTER.
sound track, then press ENTER.
AUDIO1: Select
this to record the
original stereo sound played
back on the connected DV
equipment.
AUDIO2: Select this to record the
Your unit
dubbed stereo sound played
back on the connected DV
DV IN connector
equipment.
MIX: Select this to record the sound of both "AUDIO 1" and
"AUDIO 2".
• Note that this selection is not available when the source program is
recorded in 16BIT (48 kHz) mode.
6 Press REC MODE repeatedly to set the recording mode.
DV cable
(VC-VDV 204U)
(not supplied)
DV connector
DV equipment
L
7 Locate the point from where you want to start dubbing, then
stop or pause playback by pressing the following buttons on the
remote control: I_, 1_1_, _1_1, n, II
• To play back in slow speed (1/10 of the normal speed), press II to
pause playback, then press 41_1 or lu_
• To play back frame-by-frame, press II to pause playback, then press
II repeatedly. Each press of II advances a frame.
• To change the playback direction, press 41_1 or I_.
8 Press _ L> to select
m-,'_O
then press ENTER. The
dubbing starts.
• Playback on the external DV equipment and recording on the unit
should start simultaneously.
• When the playback from the beginning is not possible, the "DV
DUBBING" controller cannot be used. Perform dubbing without using
the "DV DUBBING" controller. (: 7.below)
• To pause dubbing, press <_I:. to select _t/tO
, then press
ENTER. Both the unit and the external DV equipment pause dubbing.
Pressing II on the unit also works the same way.
• To clear the "DV DUBBING" controller from the TV screen, press ON
SCREEN.
9 Press • on the remote control to stop dubbing.
• Both the unit and the external DV equipment stop dubbing.
NOTES:
• Dubbing copyright guarded programs is not possible.
• Original DV informations such as the recording date and time are not
recorded.
• The superimposed indication during the operation or dubbing is not
recorded.
• It is not possible to perform dubbing when "VCR_" lights up on the
unit. Press VCR_ so that "VCR_" lights off.
Performing dubbing without using the "DV DUBBING"
controller
[] Press CH +/- to set the channel to "DV DUBBING".
[] Press REC MODE repeatedly to set the recording mode.
[] Start playback on the external DV equipment slightly before the
actual point from where you wish to start dubbing.
[] Press • on the unit to start recording. Or press and hold • and
press I_ on the remote control. The dubbing starts.
[] When the dubbing ends, press • on the unit, then stop
playback on the external DV equipment.
EB.[TXN6
I Slide the TV/CABLE/DBS/DVD
| EditFromA Camcorder
You can use a camcorder as the source player and your unit as the
recording deck.
[]
[]
If the camcorder
has no S-VIDEO output connector:
EN
67
switch to DVD.
1 Make connections.
[] If the camcorder has no S-VIDEO output connector:
-- connect the camcorder's AUDIO/VIDEO OUT connectors to the
unit's AUDIO/VIDEO input connectors on the front panel.
• When using a monaural camcorder, connect its AUDIO OUT
connector to the AUDIO L input connector on your unit.
[] If the camcorder has an S-VIDEO output connector: (DVD deck
only)
-- connect the camcorder's AUDIO OUT and S-VIDEO OUT
AUDIO/VIDEO input
i
connectors to the unit's AUDIO and S-VIDEO input connectors on
the front panel.
2 Press VCR/DVD
Recorder
repeatedly to select the recording deck.
3 Press CH +/- to select "F-I".
For DVD deck
• Set "FRONT AUX F-I" to "VIDEO" for the VIDEO input connector, or
"S-VIDEO" for the S-VIDEO input connector, depending on the
connector being used. (y" pg. 74)
4 Press REC MODE repeatedly to set the recording mode.
Audio/video
5 Start playback on the camcorder slightly before the actual point
from where you wish to start dubbing.
cable
(not supplied)
6 Press • on the unit to start recording. Or press and hold • and
press I_ on the remote control. The dubbing starts.
7 Press • on the unit, then stop playback on the camcorder.
NOTES:
• All necessary cables can be obtained frorn your dealer.
• Refer to the camcorder's instruction manual for operating procedure.
• The quality of dubbed picture becomes poorer than that of the
original.
AUDIO/VIDEO_OUT
Player
If the camcorder
deck only):
S-VIDEO
has an S-VIDEO output connector
(DVD
input
/
_DIO
input
Recorder
Audio cable (not supplied)
AUDIO_:_]]_]_zOUT
S-Video cable
(not supplied)
S-VIDEO
OUT
Player
I
68 ENEDITING
| EditToOr FromAnotherRecorder
You can use your unit as the source player or as the recording
deck.
NOTE:
When using another recorder as the recording deck, refer to its
instruction manual.
[]
[]
When recording on the DVD deck:
Your unit
ecoider _
TV receiver
J Slide the TV/CABLE/DBS/DVD
1
switch to DVD.
Make connections.
[] When recording on DVD deck
1) If the another recorder has no S-VIDEO connector, connect the
unit's AUDIONIDEO
INPUT connectors to the audio/video output
connectors on another recorder.
2) If the another recorder has S-VIDEO connector, connect the
AUDIO INPUT and S-VIDEO INPUT connectors to the audio and
S-video output connectors on another recorder.
• If connecting a unit with an S-VIDEO connector, it is recommended to
use an optional S-Video cable to minimize picture degradation while
editing.
[] When recording on VCR deck
1) Connect the unit's AUDIONIDEO
INPUT connectors to the
audio/video output connectors on another recorder
2 Press VCR/DVD
repeatedly to select the recording deck.
3 Press CH +/- to select "L-I" when using this unit as the
recording deck.
For DVD deck
• Set "REAR AUX L-I" to "VIDEO" for the VIDEO input connector, or
"S-VIDEO" for the S-VIDEO input connector, depending on the
connector being used. (r pg. 74)
4 Press REC MODE repeatedly to set the recording mode.
\
/
Another recorder
Player
When recording on the VCR deck:
TV receiver
%
Another recorder
L_
Player
5 Engage the Play mode of the source player.
6 Engage the Record mode of the recording deck.
7 Stop recording on the recording deck, then stop playback on the
source player.
NOTES:
• All necessary cables can be obtained from your dealer.
• When you use this unit as the source player for editing, be sure to set
"SUPERIMPOSE" to "OFF" before starting. ( ' pg. 74)
J
EDITING
E. 69
1 Connect the unit and a digital audio device using either an
optional optical cable or an optional coaxial cable.
| DigitalAudioDubbing
You can dub selected audio from a DVD or Audio CD disc to a
2 Place a disc on the unit and load an MD on the connected digital
audio device.
digital audio device.
However, it is not possible to dub copy-protected
3 Select the audio to be dubbed.
discs.
]
•e Turn
Slide on
thethe
TV/CABLE/DBS/DVD
TV and select the video
switchchannel
to DVD.
(or AV mode).
Example:
Dubbing
to an MD
4 Start playback slightly before the actual point from where you
wish to start dubbing.
5 Press II to pause playback.
6 Select the input mode on the connected digital audio device.
7 Press I_ to start playback on the unit.
Recorder
8 Start recording on the digital audio device.
9 Stop recording on the digital audio device. Then press • to stop
playback on the unit.
NOTE:
There may be a discrepancy of several seconds between where you
intend editing to start, and where it actually starts.
Digital audio device
(MD deck, etc.)
3oaxial cable
Optical cable
(not supplied)
DIGITAL
AUDIO
OUT
(not supplied)
I
I
(OPTICAL)
\
Player
Rear of unit
I
Note for connection:
Remove the protection
cap from the cable.
(COAXIAL)
DIGITAL AUDIO OUT
70 ENREMOTE
£ONTROL
II RemoteControlFunctions
caat F_VD
Remotecontrol1/2/3/4
CodeSwitching
©/I
--0=9
The remote control is capable of controlling four JVC video units
independently. Each of the units can respond to one of four codes
(1, 2, 3 or 4). The remote control is preset to send 3 code signals
because your unit is initially set to respond to 3 code signals. You
can easily modify your unit to respond to 1,2 or 4 code signals.
Slide the TV/CABLE/DBS/DVD
[N'f[R
SITUP--
switch to DVD.
[
[]
TVVOL
w/vcR--
--q
CH+/=
[]
TV Multi-BrandRemoteControl
t!p/I
Your remote control can operate the basic functions of your TV set,
In addition to JVC TVs, other manufacturer's TVs can also be
controlled.
LCABLE'DBS
...........................
%t=4
£g2}c_: cT:
dT;
E_3
• Turn off the TV using its remote
• Slide the TVlCABLEIDBSlDVD
control.
switch to TV.
d_
IMPORTANT:
Although the supplied remote control unit is compatible with JVC
televisions,
as well as many other models, it may not work with your TV.
or in some instances, may have limited function capability.
[HTER
SETUP--
• Keep pressing SET UP down during step 1.
1 Enter your TV's brand code using the number
ENTER.
m_
JVC
• Keep pressing SET UP down during step 1.
1 Press the number key "1" for 1, "2" for 2, "3" for 3 or "4" for 4
to change the remote control code, then press ENTER.
2 Press cb/I on the unit to turn off the unit.
3 Press I_ on the unit for over 5 seconds while the unit is turned
off. The code currently set appears on the front display panel.
4 Press • on the remote control to change the unit's code. The
code currently set on the remote control blinks on the front display
panel for approximately 5 seconds, and is applied to the unit.
NOTE:
When "POWER SAVE" is set to "ON" (: _ pg. 74), it is not possible to
change the remote code.
keys, then press
2 Press O/I on the unit's remote control to turn on the TV and try
operations (_" step 3).
• Once you have set the remote control to operate the TV, you do not
have to repeat this step until you replace your remote control's
batteries.
• Some brands of TVs have more than one code. If the TV does not
function with one code, try entering another.
3 Press
the corresponding button to operate the TV: cb/i, TV/VOR,
OH +/-, TV VOL., d;_ (TV Muting), number keys.
• For some brands of TVs, you must press ENTER after having
pressed the number keys.
BRAND NAME
CODE
JVC
HITACHI
MAGNAVOX
MITSUBISHI
PANASONIC
RCA
SHARP
SONY
SAMSUNG
SANYO
SEARS
TOSHIBA
ZENITH
01,03
10
O2
O3
04, 11
O5
O6
O7
12
13
13
O8
O9
REMOTE CONTROL
CableBoxOr DBSReceiverMulti-BrandRemote
Control
Your remote control can operate the basic functions of your cable
box or DBS (Direct Broadcast Satellite) receiver set. In addition to
JVC cable boxes or DBS receivers, other manufacturer's cable
boxes or DBS receiver can also be controlled.
Slide the TV/CABLE/DBS/DVD
• Keep pressing
1 Enter your
cable
then
box or DBS
number
keys,
2
cb/I on the unit's
Press
switch
SET UP down during
press
to CABLE/DBS.
]
step 1.
receiver's
brand
code
using
ENTER.
remote
control
to turn on the cable
DBS receiver
and try operations
(_" step 3).
• Once you have set the remote control to operate the cable
DBS receiver, you do not have to repeat this step until you
your remote control's batteries.
• Some brands of cable box or DBS receiver have more than
If the cable box or DBS receiver does not function with one
entering another.
3
Press
the corresponding
the
button
to operate
the cable
box or
box or
replace
one code.
code, try
box or DBS
receiver: _b/I, CH +/-, number
keys.
• For some brands of cable box, you must press ENTER after having
pressed the number keys.
• The number keys may not function with some cable boxes.
IMPORTANT:
It rnay not work with your cable box
limited function capability.
or in some
instances,
rnay have
NOTES:
• You must set the brand for your remote control and for your Controller
(_ . pg. 22) separately. The list of brands that can be controlled by
your remote control is different from the list of brands that can be
controlled by your controller.
• It's not possible to operate a cable box or DBS receiver that is not
equipped with a receiving window.
• It's not possible to set the remote control for both your cable box and
a DBS receiver at the same time. You can only set the remote control
to operate one of these units at a time.
CABLE BOX BRAND
CODE
ARCHER
CABLETENNA
CABLEVlEW
CITIZEN
CURTIS
DIAMOND
GC BRAND
GEMINI
GENERAL INSTRUMENTS
HAMLIN
JASCO
JERROLD
NOVAVlSION
OAK
PANASONIC
PULSER
RCA
REGAL
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
SPRUCER
STARGATE
TELEVlEW
TOCOM
UNIKA
UNIVERSAL
VlDEOWAY
ZENITH
01,05, 17
01, 17
15,16,17,21,25
15,16,17,21,25
02
01, 17
15,16,17,21,25
15
01,04,06,
11,
10, 18, 23
15
01,04,06,
11,
02
07
13, 14
15,16,17,21,25
13, 14
10, 18, 23
01, 16, 17
05, 16, 24
02
O7
05, 16, 17, 24,
13, 14
05, 15, 16, 17,
05, 16, 24
01,04, 16
01, 17
16, 17, 25
03, 09, 22
03, 09, 22
DBS RECEIVER
CODE
BRAND
JVC (DISH Network)
ECHOSTAR (DISH Network)
SONY (DSS)
RCA (DSS)
51
51
41
40
EN71
12, 15,28
12, 15,28
25
21,24,
25
72 ENSYSTEMCONNECTIONS
I Connecting
ToA W
DolbyDigitalDecoder
Or AnAmplifier
ith Built-inDTS
These
Digital
instructions
enable you
decoder
or an amplifier
to connect your unit to a Dolby
with built-in DTS.
1 Connect the unit and a Dolby Digital decoder or an amplifier
with built-in DTS using either an optional optical cable or an
optional coaxial cable.
NOTES:
• For Dolby Digital sound, set "DIGITAL AUDIO OUT" to "DOLBY
DIGITAL/PCM". (: 7.pg. 73)
• For DTS sound, set "DIGITAL AUDIO OUT" to "STREAM/PCM".
(: _ pg. 73)
CAUTIONS:
• This unit has a dynamic range of more than 110 dB with regards to its
Hi-Fi audio capability. It is recommended
that you check the
maximum level if you are going to listen to the Hi-Fi audio signals
through a stereo amplifier. A sudden surge in the input level to the
speakers may damage them.
• Some speakers and televisions are specially shielded to prevent
television interference.
If both are of the non-shielded
type, do not
place the speakers adjacent to the TV set as this can adversely affect
the playback picture.
Dolby Digital Decoder or
amplifier with built-in DTS
_=_=
To DIGITAL AUDIO input
Optical cable
(not supplied)
(not supplied)
l
DIGITAL AUDIO OUT
_'t
Coaxial cable
(OPTICAL)
DIGITAL AUDIO OUT
Note for connection:
Remove the protection
cable,
cap from the
(COAXIAL)
SUBSIDIARY
SETTINGS
EN 73
* The boldface settings below indicate the settings at your purchase.
| ModeSet(DVDDeck)
AUDIOOUTPUT
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TVlCABLEIDBSlDVD switch to DVD.
• DIGITALAUDIOOUT-- DOLBYDIGITAL/PCM/ STREAM/
PCM/ PCMONLY
Set to the appropriate mode according to the type of the device
connected to DIGITAL AUDIO OUT connector.
DOLBY DIGITAL/PCM: Select this when you connect the digital
input connector of a Dolby Digital decoder or an amplifier with a
builtqn Dolby Digital decoder.
STREAM/PCM: Select this when you connect the digital input
connector of an amplifier with a builtqn DTS, Dolby Digital, or
MPEG multichannel decoder.
VCR/DVD-C_D
C_D c_7_
CT_3
C_]
C_D
;C_D
C_
C--D
PCMONLY:Select
[}
SETUP.........
• ANALOGAUDIOOUT-- STEREO/ DOLBYSURROUND
Select the appropriate setting to accommodate the unit to the
connected A/V equipment. This function takes effect when a
DVD VIDEO disc is played back.
STEREO: Select this when listening to conventional two-channel
stereo audio with the unit's AUDIO OUTPUT connecters
O_OQ_
Various modes of this unit are categorized into menus nested in 2
levels shown in the following table. To change the settings of these
modes, find the desired mode in the menu (for details on each
menu, see pages 73 through 74), then follow the procedure below.
DVD SET UP
LANGUAGE SET (_" pg. 19)
AUDIO OUTPUT (, -. pg. 73)
UTILITY (7. pg. 37, 78)
FUNCTION SET UP
VIDEO IN/OUT (7. pg. 24, 74)
RECORDING SET (_. pg. 74)
DISPLAY SET (: :- pg. 74)
OTHERS (7. pg. 74)
INITIAL SET UP
TUNER SET (_, pg. 21)
STB SET (, -. pg. 22)
CLOCK SET (: -. pg. 20)
• The procedure below shows how to set the desired option of the
"2ND AUDIO RECORD" mode as an example.
1 Press VOR/DVD repeatedly so that the DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press _ P>to select "FUNCTION
4
Press _ P*to select
"RECORDING
ENTER.
5 Press/\V
SET", then press
to select "2ND
AUDIO RECORD", then press
ENTER.
6
Press/\V
this when you connect the linear PCM digital
input of other audio equipment (amplifier, MD or DAT deck, etc.).
to select the desired
option, then press ENTER.
7 Press SET UP to complete the
setting.
connected to a stereo amplifier/receiver or TV set, or in case you
want to record the audio from a DVD VIDEO disc to a Mini Disc,
etc.
DOLBY SURROUND: Select this when listening to multichannel
surround audio with the unit's AUDIO OUTPUT connectors
connected to an amplifier/receiver
decoder or a surround decoder.
with a builtqn surround
• D. RANGECONTROL-- NORMAL/ WIDERANGE/ TV
MODE
The dynamic range (the difference between the loudest sound and
the quietest one) can be compressed during playback of a program
encoded ill Dolby Digital format.
This function takes effect when a DVD VIDEO disc recorded in
Dolby Digital format is played back at low or middle volume.
NORMAL: Normally select this setting to activate this function.
WIDE RANGE: Select this to deactivate this function when you
enjoy wide dynamic range program.
TVMODE:Select this when you hear the sound through the TV's
speaker(s).
NOTES:
• This function takes no effect on programs other than that recorded in
Dolby Digital format.
• This function dose not work when Simulated Surround Effect is
activated. (__"pg. 35)
• The effect of "NORMAl" and "WIDE RANGE" may not be different
depending on discs.
SET UP", then press ENTER.
• OUTPUTLEVEL-- STANDARD
/ LOW
You can lower the output level of analog audio to accommodate
unit to the connected AN equipment.
STANDARD: Normally select this setting.
LOW: The output level of analog audio is lowered.
the
74 ENSUBSIDIA
R Y SE"i'TINGS
VIDEOIN/OUT
• GRAYBACK-- OFF/ ON
• MONITORTYPE-- 4:3LB/ 4:3PS/ 16:9 AUTO/ 16:9 FIX
You can select the monitor type depending on the TV used when
you play back DVD VIDEO discs recorded for wide-screen TVs. For
details, refer to "Monitor Set (DVD Deck Only)" (__ pg. 24).
• FRONTAUXF-1-- VIDEO/ S-VIDEO
Select the appropriate mode depending on the connector (F-l)
being used on the front panel.
VIDEO: To use the VIDEO input connector on the front panel.
S-VIDE0: To use the S-VIDEO input connector on the front panel.
• REARAUXL-1 -- VIDEO/ S-VIDEO
Select the appropriate mode depending on the connector (L-l)
being used on the rear panel.
VIDEO: To use the VIDEO INPUT connector on the rear panel.
S-VIDE0: To use the S-VIDEO INPUT connector on the rear panel.
When this function is set to "ON", the TV screen becomes all grey
when receiving a channel not in use.
NOTE:
When you want to receive an unstable channel with poor signals, set
this function to "OFF".
• DIMMER-- BRIGHT/ DIM
You can change the brightness of the front display panel.
BRIGHT: Normally select this.
DIM:To dim the front display panel. (Blue lamp on the front display
panel is turned off.)
• POWERSAVE-- OFF/ ON
• XP MODERECAUDIO-- DOLBYDIGITAL/ LINEARPCM
When this function is set to "ON", you can reduce the power
consumption while the unit is turned off.
NOTES:
• During Power Save mode --- the front display panel will be turned off.
• Power Save does not work when --- the unit is in the Timer mode.
-- the unit's power is turned off after timer-recording or Instant Timer
Recording.
-- the Automatic Satellite Program Recording mode is engaged.
(_7 pg. 46)
• It takes some time for the unit to complete initialisation after you turn
on unit power, with "WAKE UP" blinking on the front display panel.
You can select the audio format when you record a program in XP
mode. When this function is set to "LINEAR PCM", you can obtain
a high-quality audio sound.
DOLBY DIGITAL: To record in Dolby Digital format.
LINEAR PCM: To record in Linear PCM format.
This unit offers you the choice to view on-screen messages in 3
different languages.
For details, refer to "On-screen Language Set" (2" pg. 19).
• 2ND AUDIORECORD
-- OFF/ON
OTHERS
RECORDING
SET
• SAVEAS LIBRARY-- 0FF/ON
When this function is set to "ON", the recording information is
automatically stored in the library. For details, refer to "Modify
Library Information" (_" pg. 60).
When this function is set to "ON";
If a SAP program is received, the SAP audio is recorded on L/R
tracks. The main audio is not recorded.
If a non-SAP program is received, the main audio is recorded on L/
R tracks.
When this function
recorded.
is set to "OFF", the SAP audio cannot be
NOTE:
When the channel is changed on the unit;
• The "MONO" indicator appears on the screen for about 5 seconds if
the program is a monaural broadcast.
• The "STEREO" indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
• Both "STEREO" and "SAP" indicators appear when a stereo program
is accompanied by SAP sound.
• Both "MONO" and "SAP" indicators appear when the main audio on
the monaural broadcast is accompanied by SAP sound.
DISPLAYSET
• SUPERIMPOSE--OFF/ AUTO
When this function is set to "AUTO", various operational indicators
appear on the TV screen. Messages appear in the selected
language. (: _ pg. 19)
OFF: To turn off superimposed indications.
AUTO: To superimpose operational indications for approximately
five seconds just after the corresponding operation.
NOTES:
• Even when "SUPERIMPOSE" is set to "OFF", you call display the
various operational indicators by pressing ON SCREEN. To clear the
operational indicators, press ON SCREEN again.
• When you use this unit as the source player for editing, be sure to set
"SUPERIMPOSE" to "OFF" before starting. (_ . pg. 74)
• When you select "AUTO", during playback, the operation mode
indicators may be disturbed depending on the type of disc being
used.
• ONSCREENLANGUAGE
• RESUME--ON/OFF/DISC RESUME
When this function is setto "ON" or "DISC RESUME", you can use
the resume function. (_" pg. 27)
ON: You can start playback from the resume point of the placed
disc.
OFF:You cannot use the resume function.
DISC RESUME: The unit retains a memory of the resume points of
the last 30 discs played back, even though they have been
ejected.
NOTE:
"DISC RESUME" setting works on DVD VIDEO, VCD and already
finalised DVD-R/DVD-RW (video mode) discs. For other types of discs,
the function under "ON" setting will be applied even if "RESUME" is set
to "DISC RESUME".
SUBSIDIARY
* The boldface
IIModeSet(VCRDeck)
settings
below indicate
the settings
SETTINGS
EN 75
at your purchase.
• PICTURECONTROL-- NORM/ EDIT/ SOFT/ SHARP
This feature helps you to adjust the playback picture quality
according to your preference. Normally select "NORM".
NORM: Picture quality is adjusted automatically.
EDIT: Minimizes picture degradation during editing (recording and
playback).
SOFT: Reduces image coarseness when viewing overplayed tapes
containing a lot of noise.
SHARP:Clearer, sharper-edged picture when viewing images with
lots of fiat, same-colored surfaces such as cartoons.
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TVlCABLEIDBSlDVD switch to DVD
[email protected]/DVD--
NOTES:
• When you select "EDIT", "SOFT" or "SHARP", the selected mode will
not change until you select another mode.
• When you select "EDIT" to dub tapes, be sure to select "NORM" after
you finish dubbing the tapes.
SETUP.....
_' ....
• SUPERIMPOSE
-- AUTO/ OFF
When this function is set to "AUTO", various operational indicators
appear on the TV screen. Messages appear in the selected
language. (2" pg. 19)
_r j
NOTES:
• Even when "SUPERIMPOSE" is set to "OFF", you can display the
various operational indicators by pressing ON SCREEN. To clear the
operational indicators, press ON SCREEN again.
• When you use this unit as the source player for editing, be sure to set
"SUPERIMPOSE" to "OFF" before starting.
• During playback, the operation mode indicators may be disturbed
depending on the type of tape being used.
Jvc
You can change various mode settings on the Function Set screen.
To change the settings of these modes, find the desired mode in
the menu (for details on each menu, see pages 75 through 76),
then follow the procedure below.
• AUTOSP_EP TIMER-- ON/ OFF
1 Press VCR/DVD repeatedly so that the VCR lamp lights up on
the unit.
2 Press SET UP to access the
Function Set screen.
3 Press/\V
to select the item you
want to change, then press ENTER or b.
to select the desired mode.
4 Press SET UP to complete the
setting.
AUTO SP_EP TIMER
VIDEO STABILIZER
BLUEBACK
2ND AUDIO RECORD
_(SE__;
OFF
OFF
ON
OFF
t
When this function is set to "ON", the unit automatically switches to
EP mode to allow complete recording if there is not enough tape to
record the entire program while timer-recording in SP mode.
For Example:
Recording a program of 140 minutes in length onto a 120-minute
tape
Approximately 110 minutes
Approximately 30 minutes
........................................................
I
SP mode
I
EP mode
Total 140 minutes
I
Make sure you set this function to "ON", before the timer-recording
starts.
NOTES:
• If you have programed the unit to timer-record
2 or more programs,
the second program and those thereafter
may not fit on the tape if
you set "AUTO SP-,-EP TIMER" to "ON". In this case, make sure the
mode is not engaged, then set the tape speed manually during timer
programing.
• In order to ensure that the recording fits on the tape, this feature may
leave a slight non-recorded
section at the end of the tape.
• There may be some noise and sound disturbance
at the point on the
tape where the unit switches from SP to EP mode.
• The Auto SP-'*EP
Timer feature is not available during ITR (Instant
Timer Recording),
and the feature will not work properly on the
following tapes: T(ST)-30, T(ST)-60, T(ST)-90,
and T(ST)-120
76 ENSUBSIDIAR Y SETTINGS
• VIDEOSTABILIZER
-- ON / OFF
When this function
is set to "ON", you can automatically
correct
vertical vibration
in the picture when playing back unstable
recordings
made on another
recorder.
NOTES:
• When you finish viewing a tape, be sure to set this function to "OFF".
• Regardless of the setting, this function has no effect during recording
and during special effects playback.
• The on-screen display may jitter vertically when this function is set to
"ON".
• To watch
recordings
with close-caption,
set this function
to "OFF".
• BLUEBACK-- ON/ OFF
When
when
this function
is set to "ON", the TV screen
receiving
a channel not in use.
becomes
all blue
NOTE:
When you want to receive an unstable
this function to "OFF".
channel
with poor signals,
set
• 2ND AUDIORECORD
-- ON /OFF
When
this
function
is set to "ON";
If a SAP program
is received,
the SAP audio
tracks. The main audio is not recorded.
If a non-SAP
R tracks.
When this
recorded.
program
function
is received,
the main
is set to "OFF",
is recorded
audio
the SAP
on L/R
is recorded
audio
cannot
on L/
be
NOTE:
When the channel is changed on the unit;
• The "STEREO"
indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
• Both "STEREO"
and "SAP" indicators appear when a stereo program
is accompanied
by SAP sound.
SUBSIDIARY
| Changing
VCRPlus+Setting
The VCR Plus+ programing system assigns a VCR Plus+ guide
channel to the TV channels and the cable channels. These guide
channel numbers are also called the VCR Plus+ channel codes.
Most TV listings have a section, usually a chart, indicating the
guide channel numbers assigned to each station.
To ensure that VCR Plus+ timer recording operates correctly, it is
necessary to set the VCR Plus+ "Guide Channel Set" for each
station.
If you have moved to a different area or if a broadcasting station's
channel number has been changed, perform the following steps to
set the correct guide channel number.
NOTES:
• In many instances, the VCR Plus+ guide channel numbers for cable
and broadcast TV stations DO NOT match the channel number on
which it is received by your unit or cable box. Check your TV listing,
or contact your cable supplier for details.
• Many TV stations can be viewed on cable. Check your TV listing, or
contact your cable supplier for details.
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TV/CABLE/DBS/DVD
switch to DVD.
VCR/DVD--
dZ_J d_J
L_-J
ENTER=,_
SETUP ..............
[?i]FJ
Jvc
(ii]
SETTINGS
EN 77
GuideChannelNumberSet
1 Press VCR/DVD
the unit.
2
repeatedly so that the DVD lamp lights up on
Press SET UP to access the Main Menu screen.
3 Press 4 b. to select "INITIAL SET UP", then press ENTER.
4 Press _ b. to select "TUNER
SET", then press ENTER.
5 Press/\V
to select "GUIDE
CHANNEL SET", then press
ENTER.
6
Press/\V
to select "GUIDE CH",
then press ENTER.
_.
,,.,.,__
7 Press/\V
to select the Guide
Channel number for the desired
station as shown in the TV listings.
Then press ENTER.
• To change the Guide Channel
number in 10 increments, press and
hold J ,_7
• If you receive your channels with a cable box and if you have properly
set your Controller, "CATV CH"appears in place of "DVD CH". If not,
perform "Cable Box and/or DBS Receiver Control Setting (DVD Deck
Only)"( "pg. 22).
8 Press/\V
to select "DVD CH", then press ENTER. Press/'_V
to select the number of the unit's channel position on which the
Guide Channel number's broadcast is received by the unit or the
DBS receiver. Then press ENTER.
• To timer-record a satellite program with the VCR Plus+ system, you
need to install the Controller and perform the procedure described in
"Cable Box and/or DBS Receiver Control Setting (DVD Deck Only)"
(..:J"pg. 22).
• Repeat steps 6 and 8 as necessary.
Press SET UP to complete the setting.
Guide Channel Number
"Guide Channel (GUIDE CH) number" refers to the assigned TV
station numbers, according to broadcast area, for the VCR Plus+
timer recording. The Guide Channel numbers can be found in
most TV listings.
78 ENSUB$IDIA
R Y SETTINGS
| FormatA Disc(DVDDeckOnly)
FormatA DVD-RAMDisc
1 Press VCR/DVD
the unit.
repeatedly so that the DVD lamp lights up on
2 Press SET UP to access the Main Menu screen.
3 Press/\V
Some DVD-RAM/RW discs are unformatted.
Format the disc when you use an unformatted
delete all recordings and data on the disc.
disc or you want to
ATTENTION:
• When a disc is formatted, all recordings and data are erased. It is
impossible to restore them.
• Never turn off the unit or disconnect
the mains power cord while
"NOW FORMATTING..."
is displayed on the TV screen.
•
•
•
•
Turn
Turn
Slide
Load
on the unit.
on the TV and select the video channel (or AV mode).
the TV/CABLE/DBS/DVD
switch to DVD.
a DVD-RAM/RW
disc to format.
4 b to select "DVD SET UP", then press ENTER.
4 Press _ [.> to select "UTILITY",
then press ENTER.
5 Press/\V
to select "FORMAT",
then press ENTER. Press 4 b_ to
select "YES", then press ENTER
when "DISC WILL BE
FORMATTED" appears on the TV
screen.
6 Press _ b, to select "OK", then
press ENTER when "DISC FORMATTING
appears on the TV screen.
WAS SELECTED"
FormatA DVD-RWDisc
1 Perform steps 2 to 4 of "Format A DVD-RAM Disc" on the above
before continuing.
VCR/DVD-CT:J
Eq_
C_J
CTj
d___-J C_-J
C'P
CdP
CP
--
[NfER=
SETUP..........
,
] ::
Press/'_V to select "FORMAT", then press ENTER. Press 4
to choose "VR MODE" or "VIDEO MODE", then press ENTER
when "DISC WILL BE FORMATTED" appears on the TV screen.
"VR MODE":
To be chosen when you want to record, erase, or
edit data on the disc repeatedly.
"VIDEO MODE": To be chosen when you want to erase all the data
on the disc once played back to record new data,
or play back the disc on other DVD players.
3 Press
ti_ Fj
...............4:
Lii-?
_ b> to select "YES", then press ENTER when "DISC
WILL BE FORMATTED IN VR MODE/VIDEO MODE" appears on
the TV screen.
NOTES:
• It is impossible to format Version 1 0 DVD-RW discs in Video mode.
• It is impossible to format DVD-R discs.
• All the programs on a disc will be deleted once the disc is formatted
even if they are protected titles. (: -" pg. 57)
SUBSIDIARY SETTINGS
| FinalizeA Disc(DVDDeckOnly)
Finalizing DVD-R/RW discs recorded on this unit makes it possible
for the discs to be played back on other DVD players. DVD-RW
discs are finalized in the mode that the discs were formatted,
enabling playback on compatible DVD players.
Titles input in the Library Database DVD Navi are registered as
titles in the DVD menu. (: -" pg. 57)
•
•
•
•
Turn
Turn
Slide
Load
on the unit.
on the TV and select the video channel (or AV mode).
the TV/CABLE/DBS/DVD
switch to DVD.
a DVD-R/RW disc to finalize.
EN 79
FinalizeA DVD-R/RWDisc
1 Perform steps 2 to 4 of "Format A DVD-RAM Disc" (: -" pg. 78)
before continuing.
2 Press/\V
to select "FINALIZE", then press ENTER. Press 4 P>
to select "YES", then press ENTER when "DISC WILL BE
FINALIZED" appears on the TV screen.
3 Press 4 P* to select "OK", then press ENTER when
"FINALIZING WILL MAKE DISC READ-ONLY" appears on the TV
screen.
4 Press SET UP to return to the normal screen.
• Menu screen is cleared.
• Once a DVD-R/RW (Video mode) disc has been finalized, the
displays for original and play list do not appear. Only display for
library appears.
• Once a DVD-RW (VR mode) disc has been finalized, it can be played
on DVD players compatible with VR mode.
CancelTheFinalizationOf A DVD-RWDisc
VCl/DVI-}C_ZJCs_JO_LJ
CSt-J
CC_-J C_-J
1 Load a DVD-RW disc to cancel the disc finalization, and perform
steps 2 to 4 of "Format A DVD-RAM Disc" (: -" pg. 78) before
continuing.
Press/\V
to select "CANCEL
press ENTER.
DISC FINALIZATION",
then
Press 4 L'_.to select "OK", then press ENTER when "CANCEL
DISC FINALIZATION" appears on the TV screen.
4 Press SET UP to return to the normal screen.
• When the disc finalization is cancelled, the mode in which the disc
was formatted is restored, making the disc recordable. (-" pg. 9, 78)
SETIP ......
Jvc
Before finalizing
• It is possible to record on a blank space.
• It is possible to enter a program title. (:2" pg. 57)
• It is possible to delete programs. (:y" pg. 57)
• It is impossible to overwrite recorded areas of DVD-R discs.
• Available recording capacity does not increase even if a recorded
program is deleted from a DVD-R disc.
• It is impossible to record or edit DVD-R/RW
discs recorded on other
devices even if they have not been finalized.
After finalizing
(For DVD-R/RW
(Video mode) discs)
• Video and audio that have been recorded by then are recorded in
conformity to the DVD Video standard, enabling you to play back the
discs as DVD VIDEO discs.
• Although DVD-R/RW
discs finalized on this unit become playable on
DVD players compatible with DVD-R/RW discs, some discs still may
not play, for which JVC cannot take responsibility.
• Marked points marked before finalizing will be deleted, and programs
will be divided automatically
into "chapters" approximately
every 5
minutes. (:_" pg. 27)
• Depending on the DVD players and DVD-R/RW discs used, and on
the conditions of recording, it may not be possible to play back the
discs. In this case, play back the discs on this unit.
• Additional recordings become impossible.
80 ENSUBSIDIA
R Y SETTINGS
IIScanModeSet
IITrayLock(DVDDeckOnly)
If you connect the unit and TV with Component Video Connection
(_ pg. 17), you can select the scan mode from two modes:
Interlaced scan mode which is used in the conventional TV
You can lock the disc tray to prohibit the unwanted disc ejection by
children.
system, and Progressive scan mode which enables reproduction
higher-quality images. For details, refer to "GLOSSARY"
(: _ pg. 86).
of
I•
Turn off the unit.
ATTENTION:
Your TV needs to be compatible with Progressive.
• Turn on the unit.
• Turn on the TV and select the video channel (or AV mode).
• Slide the TV/CABLE/DBS/DVD
switch to DVD.
To lock tray
While the unit is turned off, press and hold Ig, then press A
(OPEN/CLOSE) on the unit. "LOCKED" appears on the front
display panel and the disc tray is locked.
VCR/DVD
_
CTb
C_
C_b
C_b
L-_Q
C_'_J
_- _
To unlock tray
While the unit is turned off, press and hold Ig, then press A
(OPEN/CLOSE) on the unit. "UNLOCK" appears on the front
display panel.
-- PROGRESSIVE
S(AN
_VC
1 Press VCR/DVD repeatedly so that the DVD lamp lights up on
the unit.
2 Press PROGRESSIVE
SCAN for 3 or more seconds.
• Video output indicator (_) lights on the front display panel if
Progressive scan mode has been established. (:y" pg. 14)
• Each press of PROGRESSIVE SCAN for 3 or more seconds
switches the scan mode.
NOTES:
• When the Progressive scan rnode is engaged, no video signal is
output from AUDIO/VIDEO and S-VIDEO OUTPUT connectors.
• Interlaced scan mode is the setting at your purchase.
• Interlaced scan mode might be suitable depending on video material.
• Scan mode cannot be set while menu screen is displayed.
Watch the image on VCR deck
mode via component
video
in the Progressive
scan
[] Set the Progressive-compatible
TV to the component input
mode.
[] Press VCR/DVD repeatedly so that the DVD lamp lights up
on the unit, then press PROGRESSIVE SCAN for 3 or more
seconds so that the Video output indicator (_) lights on the front
display panel.
[] Press VCR/DVD repeatedly so that the VCR lamp lights up
on the unit.
[] Press VCR-*.
• "VCR_" lights up on the unit.
NOTES:
• Be sure to engage the DVD deck in stop mode.
• It is not possible to perform the above steps when the DVD deck is
in timer standby mode.
I
TROUBLESHOOTING
EN81
Before requesting service for a problem, use this chart and see if
you can solve the trouble yourself. Small problems are often easily
solved, and this can save you the trouble of sending your unit off
for repair.
Playback(DVD Deck)
General
--*Press VOR/DVD repeatedly so that the DVD lamp lights up on
the unit.
• The AC power plug is disconnected from the AC outlet.
---*Connect the AC power plug to the AC outlet securely. (: _"pg. 17)
• The TV receiver's channel selector is not set to the video
channel or AV mode.
i i'II _
!I ['lll_ ri'lll i _
,,'llljlil';_ll'l_
---*Remove the batteries, wait for 5 minutes or more, then load the
butteries again.
• The setting of the remote control code is inappropriate.
---*Set the same remote control code (1,2, 3, or 4) on both the unit
and the remote control.(
"pg. 70)
• The batteries are discharged.
---*Replace the dead batteries with new ones.
• The source (another video recorder, camcorder) has not been
properly connected.
---*Confirm that the source is properly connected.
• All necessary power switches have not been turned on.
• The DVD deck is not selected.
-*If you are using the RF connection,
video channel.
set the TV receiver to the
-*If you are using the AV, S-VIDEO or Component
connection, set the TV to its AV mode.
Video
• The unit's video channel has not been correctly set.
-*Perform the video channel set. (_ pg. 17)
• When interlace scanned program is played back, progressive
scan mode is selected.
-*Press and hold PROGRESSIVE
the front display panel.
SCAN until _
disappears from
---*Confirm that all units' power switches are turned on.
• The setting of the input channel position is inappropriate.
-*Select the input channel position ("F-1" or "L-I") that
corresponds to the input terminal connected to the external
equipment. (_-" pg. 68)
• The record safety tab has been removed when dubbing to the
cassette.
• The disc is loaded upside down.
-*Place the disc on the disc tray with the playback surface facing
downward. (_ pg. 11)
• A disc not being compatible with the unit is loaded.
-*Load a playable disc on the unit. (: _ pg. 8)
• A dirty disc is loaded.
-*Clean the disc. (_" pg. 11)
• Defective disc is loaded.
-*Using
-*Replace
-*Set
adhesive tape, cover the hole where the tab was removed.
"SUPERIMPOSE"
to "OFF". (2" pg. 74, 75)
• There are cases when the operation is prohibited on the disc.
• Lightning or static electricity may cause malfunction of the unit.
-*Press cb/I to turn the power off, then press the button again to
turn the power on.
the warped or scratched disc with a normal one.
-*Images are blurred or distorted at the point where the playback
speed changes and this is not a malfunction of the unit.
,il,l_'_ ,"J_r4,_tl'i_
ITl'_'ll_ik'l'ill
-*Playback does not start for approximately 30 seconds after
recording is stopped and this is not a malfunction of the unit.
• The Parental Lock is engaged and the disc is rated higher than
the set level.
-*Release the Parental Lock temporarily or change the set level.
( "pg. 37)
82 EN TROUBLESHOOTING
Playback(VCRDeck)
Recording(VCRDeck)
• The VCR deck is not selected.
---*Press VCR/DVD
the unit.
repeatedly so that the VCR lamp lights up on
• The unit is in the Record Pause mode.
Press I_ to resume recording.
• The tape is already fully rewound or fast-forwarded.
---*Check the cassette.
• There is no cassette loaded, or the cassette loaded has had its
record safety tab removed.
-*Insert a cassette, or using adhesive tape, cover the hole where
the tab was removed.
• The TV receiver's channel selector is not set to the video
channel.
-'+If you are using the RF connection,
video channel.
set the TV receiver to the
-'+If you are using the AV connection,
the AV mode.
the TV receiver is not set to
• The unit's video channel has not been correctly set.
---*Perform the video channel set. (: -" pg. 17)
• "L-I" or "F-I" has been selected as the input mode.
-*Set to the desired channel.
• The camcorder has not been properly connected.
-*Confirm that the camcorder is properly connected.
• The input mode is not correct.
-*Set the input mode to "F-I".
• This is normal.
• The automatic tracking mode is engaged.
-*Try manual tracking. (_" pg. 49)
• The video heads may be dirty.
-*Use
a dry cleaning cassette ECL-3F, or consult your JVC dealer.
• The automatic tracking mode is engaged.
-*Try manual tracking. (: :" pg. 49)
Recording(DVD Deck)
i_"_ ,__
_ .__i
I,_
_'_ M
• The channel position does not correspond to that in the
receiving area.
-*Set the correct channel position for the receiving broadcast.
( "pg. 21 )
• No disc or a disc not being compatible with the unit is loaded.
-*Load a recordable disc on the unit. (: -" pg. 8)
• The disc loaded is not formatted.
-*Format the disc. ( pg. 78)
• A finalized DVD-R disc is loaded.
-*Recording cannot be made on finalized discs. Load a recordable
disc on the unit.
• The disc is full or does not have enough space for the program
to be recorded.
-*Clear
unnecessary
(: -" pg. 57)
programs on the disc or load a blank disc.
• The end of the tape was reached during recording.
-*The program may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire program.
TROUBLESHOOTING
EN83
TimerRecording(DVD Deck)
TimerRecording(VCRDeck)
• Date and time is not correct.
• Date and time is not correct.
-*Set date and time correctly. (_" pg. 20)
• The timer is not engaged.
-*Press DVD TIMER (®) and confirm that the DVD timer lamp
lights up on the unit.
• Timer recording is in progress.
-*Timer programing can't be performed while a timer recording is
in progress. Wait until it finishes.
-*Set date and time correctly. (
pg. 20)
• The timer is not engaged.
-*Press VCR TIMER (®) and confirm that the VCR timer lamp
lights up on the unit.
• Timer recording is in progress.
-*Timer programing can't be performed while a timer recording is
in progress. Wait until it finishes.
• Date and time is not correct.
• Date and time is not correct.
-*Set date and time correctly. (_• pg. 20)
• The timer is not engaged.
-*Press DVD TIMER (®) and confirm that the DVD timer lamp
lights up on the unit.
• There is a power outage while the DVD deck is in the timer
standby mode.
-*The unit does not enter timer standby mode automatically when
the power is restored to the unit. Engage the timer standby
mode again.
-*Set date and time correctly. (: , pg. 20)
• The timer is not engaged.
-*Press VCR TIMER (®) and confirm that the VCR timer lamp
lights up on the unit.
, ,,
• , ....
Ii l'!'l_t
-
,
-nn,l_ll
- , ,
II illII11 LIi]iil'_llllil,'ll_
o t;_
_,,;
• The timer is engaged but there's no cassette loaded.
-*Load a cassette with the record safety tab intact.
• The loaded cassette has had its record safety tab removed.
-*Remove the cassette and cover the hole with adhesive tape, or
insert a cassette with the record safety tab intact.
• Date and time set on the unit is not correct.
-*Set date and time correctly. (_-" pg. 20)
• The channel position does not correspond to that in the
receiving area.
-*Set the correct channel position for the receiving broadcast.
• The end of the tape was reached during timer recording.
-*The program may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
(: -"pg. 21 )
• The DBS receiver is not connected properly to this unit.
-*Connect the DBS receiver to the AUDIO/VIDEO INPUT (L-1)
connector properly. (: -" pg. 46)
entire program.
• The end of the tape was reached during Instant Timer
Recording.
-*The program may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire program.
• Power failure occurred.
• Date and time set on the unit is not correct.
-*Set
-*Set date and time correctly. (_ , pg. 20)
• The channel position does not correspond to that in the
_1111
i i h I I1_'_
_
I I1 l_I
il
lilll
Ihl
i i I
II_IIIi]
l°
I I I[I
I
l_,tltl]
l°
Ill_°
[[email protected]
i Ill
_
_
date and time correctly. (y" pg. 20)
• Eight programs have already been timer programed.
-*Clear unnecessary programs on the unit, then try timer
programing again. (: -"pg. 45)
• The PC's data recorded on a DVD-RAM drive cannot be cleared
on this unit.
-*Format the disc. (When the disc is soiled, wipe the disc with a
soft dry cloth before formatting.) (: :" pg. 11, 78)
receiving area.
-*Set the correct channel position for the receiving broadcast.
(: -"pg. 21)
IllllltiI',l!',it'_ltll
I ,"
I ,
II "
" • ,_
• The unit's channel positions have been set incorrectly.
-*Refer to "Changing VCR Plus+ _Setting" (: -" pg. 77) and reperform the procedure.
84 ENTROUBLESHOOTING
Initializing(DVD DeckOnly)
On-screenMessage(DVD DeckOnly)
-*Press cb/I to turn off the unit, press and hold cb/I, then press •
for two seconds or more.
Other Problems
• The memory is full for registration for the Navigation system. The
recording cannot be started even though the capacity for the
recording is enough. (:_" pg. 60)
For RF/AV/S-VIDEO connection
-*Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator (Q) lights off on the front display panel.
For component video connection
-*Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator ([_) lights up on the front display panel.
• The camcorder's microphone is too close to the TV.
-*Position the camcorder so its microphone is away from the TV.
• The TV's volume is too high.
-*Turn the TV's volume down.
• Those channels have been designated to be skipped.
• The remaining capacity of the memory is not enough for
registration for the Navigation system. The recording cannot be
started even though the capacity for the recording is enough.
( "pg. 60)
• A disc that is not registered in the library has been inserted.
Register the disc as necessary. (:_" pg. 60)
I! _:11--iIi] _:t_ilt:!:i,'i:!
• Appears when a title that has been selected in the library is not
contained in the loaded disc.
-...*Ifyou need the skipped channels, restore them. (2" pg. 21)
• Recording or Live Memory recording* is in progress.
-*Press II to pause the recording, change channels, then press I_
to resume recording.
* DVD deck only
• After the manual settings were made, Auto Channel Set was
performed.
-*Perform "Manual Clock Set" (:_" pg. 20).
• The clock setting data received from the host channel is
incorrect.
• Recording and/or editing cannot be performed with a loaded
DVD-RAM disc.
• The number of titles exceeds 99.
• The number of play lists exceeds 999.
• To set the timer program, the clock must be set in advance.
( "pg. 20)
• You can program this unit to timer-record as many as 8
programs. To program more, you need to cancel a timer program
already set. (y pg. 45)
-*Select a different host channel during "Semiauto Clock Set"
( "pg. 20), or perform "ManuaI CIock Set" ( "pg. 20).
• On-Disc Timer Programing has been attempted when a disc that
is not compatible with the function is loaded. (y pg. 43)
l [I] i] f.'1411l f.'] _ :i i _I]
• On-Disc Timer Programing has been attempted when a disc is
not loaded, or loaded upside down. (_" pg. 11,43)
• When a playback-only disc or a finalized disc is loaded, • has
been pressed. (:2" pg. 8)
TROUBLESHOOTING
• An invalid VCR Plus+ number has been input. (:" pg. 41)
EN85
• The unit has detected invalid contents at the start or in the
middle of playback.
• To set the timer program using the VCR Plus+ system, the
Guide Channel number must be set in advance. (:" pg. 77)
• An attempt has been made to start DV dubbing when a digital
video camera is not properly connected to the unit.
• Check the connection. (:2" pg. 66)
• Appears when you tried to input a PlusCode number during
timer recording or instant timer recording.
• A disc loaded cannot be played back on this unit since the region
number of the disc does not match that of the unit. (:2" pg. 9)
• When an incompatible disc is loaded, I_ has been pressed.
(:y" pg. 9)
• Formatting is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (:2" pg. 11, 78)
• Finalizing is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (2" pg. 11, 79)
• Cancelling disc finalization is not complete since the disc may be
dirty or damaged. Take out the disc, clean it and retry. (2" pg. 11,
79)
"J.'t_e]'Jlr:TeT:lll
il[_]Lr>"]ll[_]5
lit:[_[_]:l_]ll[_q
• During Live Memory playback, •
has been pressed. (:2" pg. 32)
i h_'ll_ :111 :[_l] 11I] I![l] [_l] l_'ll".iq :i d_ I]
• Timer recording has finished during Live Memory playback.
• Timer recording finished during Live Memory playback, then the
next timer recording is about to begin while playback continues.
• An attempt has been made to record copy-protected contents.
• An attempt has been made to record copy-once contents on a
disc that is not CPRM compatible, such as DVD-R.
86
EN
GLOSSARY
• Aspect
ratio
The ratio of vertical and horizontal sizes of a displayed image. The
horizontal vs. vertical ratio of conventional TVs is 4:3, and that of
wide-screens is 16:9.
•
Chapter
Refers to individual chapters included in a title.
• Composite
video signal
Refers to video signal comprised of three kinds of signals
combined: an image signal made up of luminance and
chrominance signals using the frequency multiplication technique;
burst signal providing the basis for color reproduction; and
synchronization signal.
•
Component
video
signal
A video signal system where parts of information necessary for
reproducing image signal comprised of the three primary colors of
light are transmitted via separate signal lines. Types of signal, such
as R/G/B, Y/PB/PR, etc., are available.
•
Disc
menu
A screen display prepared for allowing selection of images,
sounds, subtitles, multiangles, etc. recorded on a DVD disc.
•
Dolby
Digital
(AC-3)
A six-channel system consisting of left, centre, right, left rear, right
rear and LFE (Low-Frequency Effect channel, for use with a subwoofer) channels. All processing is done in the digital domain.
Not all Dolby Digital discs contain six (5.1) channels of information.
• Down-mix
• Multiangle
By recording multiple scenes progressing at the same time ill a
single title, the user can select view angles. This feature is called
the multiangle function.
• Multichannel
DVD is specified to have each sound track constitute one sound
field. Multichannel refers to a structure of sound tracks having
three or more channels.
• Multilanguage
When a title is created to cope with multiple languages, it is
generally called a multilanguage title.
•
NTSC
(National
television
system
committee)
A black and white and color television system format used in the
U.S.A., Canada, Mexico and Japan.
• PAL (Phase Alternation
by Line)
A color television system format used extensively
Europe.
• Parental
Lock
in Western
A feature of this system to automatically determine whether or not
to reproduce particular DVD software by comparing its parental
lock level (a measure of undesirability of scenes, etc. from
educational viewpoint) set for the software beforehand with that set
on this system by the user; if the software's level is less restrictive
than the user-set level, it will be reproduced.
Internal stereo mix of multichannel surround audio by a DVD
player. The down-mix signals are output from stereo output
connectors.
• Playback control (PBC)
Refers to the signal recorded on Video CDs for controlling
reproduction. By using menu screens recorded on a Video CD that
supports PBC, you can enjoy interactive-type software as well as
software having a search function.
•
•
DTS
Progressive
scan
A Digital Surround audio encoding format configured with six (5.1)
channels, similar to Dolby Digital. It requires a decoder, either in
the player or in an external receiver. DTS stands for Digital Theater
Systems.
Not all DTS discs contain six (5.1) channels of information.
• Interlaced
scan
Progressive scan displays all the horizontal lines of a picture at one
time, as a single frame. This system can convert the interlaced
video from DVD into progressive format for connection to a
progressive display. It dramatically increases the vertical
resolution.
In the conventional video system, a picture is shown on the display
monitor in two halves. The Interlaced scan system places lines of
the second half of the picture in-between lines of the first half of the
picture.
• JPEG
A system for allowing discs to be played back only ill the regions
designated beforehand. All the countries in the world are grouped
into six regions, each region being identified by a specified Region
Code (or region number). If the Region Code given to a disc
includes a numeral which matches one in the Region Code of a
player, the player can play back the disc.
A still-picture data compression system proposed by the Joint
Photographic Expert Group, which features small decrease in
image quality in spite of its high compression ratio.
• Letter box
A method of displaying wide images like movies in the centre of a
4:3 TV screen with no part of the image deleted, by placing black
bands on the top and bottom of the screen. This name has resulted
from the screen form looking literally like a letter box.
•
Linear
PCM
(PCM:
Pulse
Code
Modulation)
A system for converting analog sound signal to digital signal for
later processing, with no data compression used in conversion.
•
MP3
A file format with a sound data compression
abbreviation of Motion Picture Experts Group
Layer 3. By using MP3 format, one CD-R/RW
times as much data volume as a regular CD
• MPEG
system, "MP3" is the
I (or MPEG-1 ) Audio
can contain about 10
can.
A family of Standards for compressing audio-visual information.
"MPEG" standards include MPEG-1, MPEG-2 and MPEG-4. Video
CD and MP3 are based on MPEG-1, while DVD is based on
MPEG-2. MPEG stands for Moving Picture coding Experts Group.
•
•
Region
Sampling
Code
frequency
Frequency of sampling data when analog data is converted to
digital data. Sampling frequency numerically represents how many
times the original analog signal is sampled per second.
• Surround
A system for creating three-dimensional sound fields full of realism
by arranging multiple speakers around the listener.
• Transfer
rate
The rate of transferring digital data. Usually the measure is in baud
per second. The DVD system applies a variable transfer rate
system for high efficiency.
SPECIFICATIONS
LVJlH=[oTl:_lJH[o]
[LvL_.-]
D._]
_ =I_I=IiT:I II
Power requirement
AC 120 V%, 60 Hz
Power consumption
Power on: 43 W
Power off: 16.5 W
Temperature
Operating: 5°C to 35°C (41°F to 95°F)
Storage: -20°C to 60°C (-4°F to140°F)
Operating position
Horizontal only
Dimensions (WxHxD)
435 mm x 96 mm x 347 mm (17-3/16" x 3-13/16" x 13-11/16")
Weight
6.1 kg (13.5 Ibs)
U IH =[oTl:_UJ
H [o][_]
Recording format
DVD-RAM: DVD Video Recording
DVD-R: DVD-Video format
EN 87
Signal system
NTSC color signal and EIA monochrome signal, 525 lines/60 fields
Recording system
DA4 (Double Azimuth) head helical scan system
Format
VHS NTSC standard
Maximum recording time
(SP): 210 rain. with ST-210 video cassette
(EP): 30 min. with ST-210 video cassette
Signal-to-noise
ratio
45 dB
Horizontal resolution
230 lines
Frequency range
(Normal audio): 70 Hz to 10,000 Hz
(Hi-Fi audio): 20 Hz to 20,000 Hz
Input/Output
RCA connectors: IN x 2, OUT x 1
format
DVD-RW: DVD-Video format, DVD Video Recording format
Recording time
Maximum 8 hours (with 4.7 GB disc)
(XP): Approx. 1 hour
(SP): Approx. 2 hours
(LP): Approx. 4 hours
(EP): Approx. 6 hours
(FR): Approx. 1 hour - 8 hours
Audio recording system
Dolby Digital (2 ch)
Linear PCM (XP mode only)
Video recording compression
system
MPEG2 (CBR/VBR)
Input/Output
S-video input:
Y: 0.8 - 1.2 Vp-p, 75 ohms
C: 0.2 - 0.4 Vp-p, 75 ohms
S-video output:
Y: 1.0 Vp-p, 75 ohms
C: 0.3 Vp-p, 75 ohms
Video input: 0.5 - 2.0 Vp-p, 75 ohms (pin jack)
Video output: 1.0 Vp-p, 75 ohms (pin jack)
Audio input:
-8 dB, 50 kilohms (pin jack)
Corresponding to mono (left)
Audio output: -8 dB, 1 kilohms (pin jack)
i.Link: 4-pin for DV input
Component video output:
Y: 1.0 Vp-p, 75 ohms
CB/CR, PB/PR: 0.7 Vp-p, 75 ohms
Corresponding to copy protection
Digital audio output:
Optical: -18 dBm, 660 nm
Coaxial: 0.7 Vp-p, 75 ohms
Corresponding to Dolby Digital and DTS Digital Surround
Bit stream
Selectable in digital audio output setting menu
Specifications
shown are for SP mode unless otherwise
specified.
Jill !1_ itidlLV_l_ il
Tuning system
Frequency synthesized tuner
Channel coverage
VHF: Channels 2 - 13
UHF: Channels 14 - 69
CATV: 113 Channels
RF output
Channel 3 or 4 (switchable;
75 ohms, unbalanced
Memory backup time
Approx. 5 seconds
r:I_]
preset to Channel 3 when shipped)
:_.'$._o]:| I:[..'-]
Provided accessories
RF cable x 3,
Antenna splitter,
Infrared remote control unit,
"AA" battery x 2
E.& O.E. Design and specifications
notice.
subject to change without
AI"rENTION:
This unit contains rnicrocornputers
External electronic
noise or
interference
could cause malfunctioning.
In such cases, switch the
unit off and unplug the mains power cord. Then plug it in again and
turn the unit on. Take out the disc. After checking the disc, operate
the unit as usual.
88 ENAPPENDIX
LanguageCodeList
AA
Afar
IK
Inupiak
RN
Kirundi
AB
Abkhazian
IN
Indonesian
RO
Rumanian
AF
Afrikaans
IS
Icelandic
RLI
Russian
AM
Ameharic
IW
Hebrew
RW
Kinyarwanda
AR
Arabic
JA
Japanese
SA
Sanskrit
AS
Assamese
JI
Yiddish
SD
Sindhi
AY
Aymara
JW
Javanese
SG
Sangho
AZ
Azerbaijani
KA
Georgian
SH
Serbo-Croatian
BA
Bashkir
KK
Kazakh
SI
Singhalese
BE
Byelorussian
KL
Greenlandic
SK
Slovak
BG
Bulgarian
KM
Cambodian
SL
Slovenian
BH
Bihari
KN
Kannada
SM
Samoan
BI
Bislama
KO
Korean (KOR)
SN
Shona
BN
Bengali, Bangla
KS
Kashmiri
SO
Somali
BO
Tibetan
KU
Kurdish
SQ
Albanian
BR
Breton
KY
Kirghiz
SR
Serbian
CA
Catalan
LA
Latin
SS
Siswati
CO
Corsican
LN
Lingala
ST
Sesotho
CS
Czech
LO
Laothian
SLI
Sundanese
CY
Welsh
LT
Lithuanian
SW
Swahili
DZ
Bhutani
LV
Latvian, Lettish
TA
Tamil
EL
Greek
MG
Malagasy
TE
Telugu
EO
Esperanto
MI
Maori
TG
Tajik
ET
Estonian
MK
Macedonian
TH
Thai
ELI
Basque
ML
Malayalam
TI
Tigrinya
FA
Persian
MN
Mongolian
TK
Turkmen
FJ
Fiji
MO
Moldavian
TL
Tagalog
FO
Faroese
MR
Marathi
TN
Setswana
FY
Frisian
MS
Malay (MAY)
TO
Tonga
GA
Irish
MT
Maltese
TR
Turkish
GD
Scots Gaelic
MY
Burmese
TS
Tsonga
GL
Galician
NA
Nauru
TT
Tatar
GN
Guarani
NE
Nepali
TW
Twi
GLI
Gujarati
OC
Occitan
LIK
Ukrainian
HA
Hausa
OM
(Afan) Oromo
LIR
Lirdu
HI
Hindi
OR
Oriya
LIZ
Lizbek
HR
Croatian
PA
Panjabi
Vl
Vietnamese
HLI
Hungarian
PL
Polish
VO
Volapuk
HY
Armenian
PS
Pashto, Pushto
WO
Wolof
IA
Interlingua
PT
Portuguese
XH
Xhosa
IE
Interlingue
QLI
Quechua
YO
Yoruba
RM
Rhaeto-Romance
ZLI
Zulu
APPENDIX
EN
Country/AreaCodeListfor ParentalLock
AD
Andorra
CK
Cook Islands
GN
Guinea
AE
United Arab Emirates
CL
Chile
GP
Guadeloupe
AF
Afghanistan
CM
Cameroon
GQ
Equatorial Guinea
AG
Antigua and Barbuda
CN
China
GR
Greece
AI
Anguilla
CO
Colombia
GS
South Georgia and the South
Sandwich Islands
AL
Albania
CR
Costa Rica
GT
Guatemala
AM
Armenia
CU
Cuba
GU
Guam
AN
Netherlands
CV
Cape Verde
GW
Guinea-Bissau
Christmas Island
GY
Guyana
Cyprus
HK
Hong Kong
Heard Island and McDonald
Islands
Antilles
AO
Angola
CX
AQ
Antarctica
CY
AR
Argentina
CZ
Czech Republic
HM
AS
American Samoa
DE
Germany
HN
Honduras
AT
Austria
DJ
Djibouti
HR
Croatia
AU
Australia
DK
Denmark
HT
Haiti
AW
Aruba
DM
Dominica
HU
Hungary
AZ
Azerbaijan
DO
Dominican Republic
ID
Indonesia
BA
Bosnia and Herzegovina
DZ
Algeria
IE
Ireland
BB
Barbados
EC
Ecuador
IL
Israel
BD
Bangladesh
EE
Estonia
IN
India
BE
Belgium
EG
Egypt
IO
British Indian Ocean Territory
BF
Burkina Faso
EH
Western Sahara
IQ
Iraq
BG
Bulgaria
ER
Eritrea
IR
Iran (Islamic Republic of)
BH
Bahrain
ES
Spain
IS
Iceland
BI
Burundi
ET
Ethiopia
IT
Italy
BJ
Benin
FI
Finland
JM
Jamaica
BM
Bermuda
FJ
Fiji
JO
Jordan
BN
Brunei Darussalam
FK
Falkland Islands (Malvinas)
JP
Japan
BO
Bolivia
FM
Micronesia
(Federated States of)
KE
Kenya
BR
Brazil
FO
Farce Islands
KG
Kyrgyzstan
BS
Bahamas
FR
France
KH
Cambodia
BT
Bhutan
FX
France, Metropolitan
KI
Kiribati
BV
Bouvet Island
GA
Gabon
KM
Comoros
BW
Botswana
GB
United Kingdom
KN
Saint Kitts and Nevis
BY
Belarus
GD
Grenada
KP
Korea, Democratic People's
Republic of
BZ
Belize
GE
Georgia
KR
Korea, Republic of
CA
Canada
GF
French Guiana
KW
Kuwait
CC
Cocos (Keeling) Islands
GH
Ghana
KY
Cayman Islands
CF
Central African Republic
GI
Gibraltar
KZ
Kazakhstan
CG
Congo
GL
Greenland
LA
Lao People's Democratic
Republic
Switzerland
GM
Gambia
LB
Lebanon
C6te d'lvoire
89
90 EN APPENDIX
LC
Saint Lucia
NU
Niue
SZ
Swaziland
LI
Liechtenstein
NZ
New Zealand
TC
Turks and Caicos Islands
LK
Sri Lanka
OM
Oman
TD
Chad
LR
Liberia
PA
Panama
TF
French Southern Territories
LS
Lesotho
PE
Peru
TG
Togo
LT
Lithuania
PF
French Polynesia
TH
Thailand
LU
Luxembourg
PG
Papua New Guinea
TJ
Tajikistan
LV
Latvia
PH
Philippines
TK
Tokelau
LY
Libyan Arab Jamahiriya
PK
Pakistan
TM
Turkmenistan
MA
Morocco
PL
Poland
TN
Tunisia
MC
Monaco
PM
Saint Pierre and Miquelon
TO
Tonga
MD
Moldeva, Republic of
PN
Pitcairn
TP
East Timer
MG
Madagascar
PR
Puerto Rico
TR
Turkey
MH
Marshall Islands
PT
Portugal
TT
Trinidad and Tobago
ML
Mall
PW
Palau
TV
Tuvalu
MM
Myanmar
PY
Paraguay
TW
Taiwan, Province of China
MN
Mongolia
QA
Qatar
TZ
Tanzania, United Republic of
MO
Macau
RE
R4union
UA
Ukraine
MP
Northern Mariana Islands
Re
Romania
UG
Uganda
MQ
Martinique
RU
Russian Federation
UM
United States Minor Outlying
Islands
MR
Mauritania
RW
Rwanda
US
United States
MS
Mentserrat
SA
Saudi Arabia
UY
Uruguay
MT
Malta
SB
Solomon Islands
UZ
Uzbekistan
MU
Mauritius
SC
Seychelles
VA
Vatican City State (Holy See)
MV
Maldives
SD
Sudan
VC
Saint Vincent and the
Grenadines
MW
Malawi
SE
Sweden
VE
Venezuela
MX
Mexico
SG
Singapore
VG
Virgin Islands (British)
MY
Malaysia
SH
Saint Helena
Vl
Virgin Islands (U.S.)
MZ
Mozambique
SI
Slovenia
VN
Viet Nam
NA
Namibia
SJ
Svalbard and Jan Mayen
VU
Vanuatu
NC
New Caledonia
SK
SIovakia
WF
Wallis and Futuna Islands
NE
Niger
SL
Sierra Leone
WS
Samoa
NF
Norfolk Island
SM
San Marine
YE
Yemen
NG
Nigeria
SN
Senegal
YT
Mayotte
NI
Nicaragua
SO
Somalia
YU
Yugoslavia
NL
Netherlands
SR
Suriname
ZA
South Africa
NO
Norway
ST
Sae Tome and Principe
ZM
Zambia
NP
Nepal
SV
El Salvador
ZR
Zaire
NR
Nauru
SY
Syrian Arab Republic
ZW
Zimbabwe
LIST OF TERMS
A
A-B Repeat Playback ................................................
Accidental erasure prevention ....................................
Adjusting The Picture Quality .....................................
Angle Selection ........................................................
Audio Channel Selection ...........................................
Audio Language/Sound Selection ...............................
Auto Channel Set .....................................................
34
5]
35
28
29
28
2]
Auto Daylight Saving Time
20
........................................
91
P
Pan&Scan ................................................................
24
Play List ...................................................................
58
Playback ..............................................
25 - 37, 47 - 49
Playback Control (PBC) .............................................
29
Program Playback ....................................................
36
Q
Quick Rewind A Little ................................................
48
R
C
Check, Cancel And Change Programs ...................
45, 54
D
Delete Program ........................................................
Disc menu ...............................................................
Disc Remaining Time ................................................
Discs For Playback Only .............................................
DVD menu ...............................................................
57
26
39
8
26
E
Elapsed Recording Time Indication
.......................
9
40
G
Guide Channel Number .............................................
77
H
.............................................
I
Index Search ............................................................
Instant Timer Recording (ITR) ...............................
26, 48
48
39, 51
24
29
M
Manual Channel Set .................................................
Manual Clock Set .....................................................
Manual Tracking .......................................................
Marking Positions To Play Back Again Later ................
Menu/Audio/Subtitle Language Set .............................
2]
20
49
27
19
N
49
O
One Touch Replay ....................................................
On-screen bar ..........................................................
On-screen Language Set ..........................................
S
SAP ..................................................................
40,
Second Audio Recording .....................................
40,
Select The Switching Interval Of The Slide Show .........
Semiauto Clock Set ..................................................
Setting The Progressive Mode ...................................
Simulated Surround Effect .........................................
Skip Search .......................................................
27,
Slow Motion .......................................................
27,
Soundtrack Selection ................................................
Still Picture/Frame-By-Frame
Playback ................. 27,
Subtitle Selection ......................................................
51
5]
36
20
36
35
48
48
49
48
28
T
L
Letter Box ................................................................
Live Memory ............................................................
Next Function Memory ..............................................
Random Playback .....................................................
36
Recordable/playable discs ...........................................
8
Recording ............................................
38 - 40, 50 - 51
Recording Medium And Format ....................................
9
Recording Mode .......................................................
38
Recording Resume Function ................................
38, 50
Region Number ..........................................................
9
Register Disc ............................................................
60
Repeat Playback ................................................
i._4, 49
Resume Function .....................................................
27
39, 51
F
File Structure Of Discs ................................................
Free Rate Function ...................................................
High-Speed Search
EN
32
33
19
Tape Position Indicator ..............................................
]5
Tape Remaining Time ...............................................
51
Time Search ............................................................
35
Timer Recording ...................................
41 - 46, 52 - 54
Top menu ................................................................
26
U
Unplayable Discs ........................................................
Usable cassettes ......................................................
9
47
W
When Programs Overlap Each Other .................... 45, 54
92 EN
WARRANTY
-k
LIMITEDWARRANTY
ONLYFORPRODUCT
PURCHASED
IN U.S.A.
USAONLY
CONSUMER
VIDEO1-90
.
.k JVC COMPANY OF AMERICA warrants this product and all parts thereof, except as set forth below ONLY TO THE ORIGINAL
"k PURCHASER AT RETAIL to be FREE FROM DEFECTIVE MATERIALS AND WORKMANSHIP from the date of original retail purchase
for the period as shown below. ("The Warranty Period")
PARTS
*
-_
-k
LABOR
1 YR
_r
"_
90
DAYS
"*
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA
"k COMMONWEALTH OF PUERTO RICO.
AND IN
-k
"k
** WHAT WE WILL DO:
.
.k If this product is found to be defective, JVC will repair or replace defective parts at no charge to the original owner. Such repair and
-k
replacement services shall be rendered by JVC during normal business hours at JVC authorized service centers. Parts used for
_r
"k replacement are warranted only for the remainder of the Warranty Period. All products and parts thereof may be brought to a JVC
-k
._
-k_, authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and above which are covered on ,k
._ an in-home basis.
._
; WHAT YOU MUST DO FOR WARRANTY
SERVICE:
*-k
._ Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service center, ._.
please call toll free: (800) 252-5722.
,k
._ If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of -k
._ sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be given ._
to you by the toll-free number.
If you have any questions concerning your JVC Product, please contact our Customer Relations Department.
"k WHAT
IS NOT COVERED:
*
This limited warranty provided by JVC does not cover:
_r
1. Products which have been subject to abuse, accident, alteration, modification, tampering, negligence, misuse, faulty installation,
.k
lack of reasonable care, or if repaired or serviced by anyone other than a service facility authorized by JVC to render such service, -_
or if affixed to any attachment not provided with the products, or if the model number or serial number has been altered, tampered -k
"_
with, defaced or removed;
"_
"k 4.
"_ 5.
6.
7.
8.
Initial installation and installation and removal for repair;
Operational adjustments covered in the Owner's Manual, normal maintenance, video and audio head cleaning;
Damage that occurs in shipment, due to act of God, and cosmetic damage;
Signal reception problems and failures due to line power surge;
Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase;
Accessories;
Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase);
There are no express warranties except as listed above.
._
"_
"_
_r
THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY,
"k THE DURATION OF THE EXPRESS WARRANTY HEREIN.
JVC SHALL NOT BE LIABLE FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE,
IS LIMITED TO ;
LOSS OR ANY OTHER DAMAGES,
._-WHETHER DIRECT, INCIDENTAL OR CONSEQUENTIAL
(INCLUDING, WITHOUT LIMITATION, DAMAGE TO TAPES, RECORDS
"k OR DISCS) RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL
EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY
PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
_.
-_
"_
AND FITNESS FOR
_r
"_ Some states do not allow the exclusion of incidental or consequential damages or limitations on how long an implied warranty lasts so "_
"k these hmRat_ons or exclusions may not apply to you. This warranty gwes you specific legal rights and you may also have other nghts
._ which vary from state to state.
-_
"_
.k
JVC COMPANY OF AMERICA
DIVISION OF JVC AMERICAS CORP.
1700 Valley Road
Wayne, NJ 07470
REFURBISHED PRODUCTS CARRY A SEPARATE WARRANTY, THIS WARRANTY
REFURBISHED PRODUCT WARRANTY, PLEASE REFER TO THE REFURBISHED
PACKAGED WITH EACH REFURBISHED PRODUCT.
DOES NOT APPLY. FOR DETAILS OF
PRODUCT WARRANTY INFORMATION
For customer use:
Enter below the Model No. which is located either on the rear, bottom or side of the cabinet. Retain this information for future
reference.
Model No. :
Serial No. :
Purchase date :
Name of dealer :
"_
Memo
EN
93
94 EN Memo
Memo
EN
95
TO OUR VALUED
CUSTOMER
THANK YOU FOR PURCHASING THIS JVC PRODUCT.
WE WANT TO HELP YOU ACHIEVE A PERFECT EXPERIENCE.
NEED HELP ON HOW TO HOOK UP?
:0
I
NEED ASSISTANCE ON HOW TO OPERATE?
NEED TO LOCATE A JVC SERVICE CENTER?
LIKE TO PURCHASE ACCESSORIES?
JVC
to retain your Bill of Sale for Warranty
Service.
Do not attempt to service the product yourself
Caution
To prevent electrical shock, do not open the cabinet.
There are no user serviceable parts inside.
Please refer to qualified service personnel for repairs.
JVC
VICTOR
[email protected]
2004 VICTOR COMPANY
m
TO
HELP,
TOLL FREE: 1 (800) 252-5722
http://www.jvc.com
Remember
<_
OF JAPAN, LTD,
COMPANY
OF JAPAN,
LIMITED
F0_l
Printed in Beijing
0304MNH-ID-BJ
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement