Weslo WLTL211041 User's Manual

Weslo WLTL211041 User's Manual
USER'S MANUAL
Model No. WLTL211041
Serial No.
Write the serial number in the
space above for future reference.
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, please call:
1-888-936-4266
Mon.–Fri. 8h00 until 18h30 EST
(excluding holidays).
CAUTION
Read all precautions and instructions in this manual before using
Visit
this equipment. Save this manual
for future reference.
our website at
www.proform.com
Visit our website at
Visit our website at
www.weslo.com
Visit our website at
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING and a PART LIST are attached in the center of this manual.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read
the following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
10. When connecting the power cord (see page
8), plug the power cord into a surge suppressor (not included) and plug the surge suppressor into a grounded circuit capable of
carrying 15 or more amps. No other appliance should be on the same circuit. Do not
use an extension cord.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage,
place a mat under the treadmill.
11. Use only a CUL-listed surge suppressor of 450
joules minimum surge dissipation with voltage
rating of 400 volts or less, rated at 15 amps,
with a 1 mm2 (14-gauge) cord of 1.5 m (5 ft.) or
less in length. Do not use an extension cord.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
12. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
13. Keep the power cord and the surge suppressor away from heated surfaces.
7. The treadmill should not be used by persons
weighing more than 113 kg (250 lbs.).
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See page 4
if the treadmill is not working properly.)
8. Never allow more than one person on the
treadmill at a time.
9. Wear suitable exercise clothes when using
the treadmill. Do not wear loose clothes that
could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear athletic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
15. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
2
17. Never leave the treadmill unattended while it is
running. Always remove the key and unplug
the power cord when the treadmill is not in
use.
22. Never drop or insert any object into any
opening.
23.
DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures
described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service representative only.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO MOVE
THE TREADMILL on page 11.) You must be
able to safely lift 20 kg (45 lbs.) to raise,
lower, or move the treadmill.
19. Do not change the incline of the treadmill by
placing objects under the treadmill.
24. This treadmill is intended for in-home use
only. Do not use this treadmill in any commercial, rental, or institutional setting.
20. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
21. Inspect and properly tighten all parts of the
treadmill regularly.
WARNING:
Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown have been placed on your treadmill. If a decal is missing or illegible, please call our
Customer Service Department to order a replacement decal (see ORDERING REPLACEMENT PARTS on
page 15 of this manual). Apply the decal in the location shown.
3
BEFORE YOU BEGIN
Thank you for selecting the WESLO® CADENCE 255
DR treadmill. The CADENCE 255 DR treadmill combines advanced technology with innovative design to
let you enjoy an excellent form of cardiovascular exercise in the convenience and privacy of your home. And
when you’re not exercising, the unique CADENCE 255
DR treadmill can be folded up, requiring less than half
the floor space of other treadmills.
please call our Customer Service Departmentat 1-888936-4266, Monday through Friday 8h00 until 18h30
Eastern Time (excluding holidays). To help us assist
you, please note the product model number and serial
number before calling. The model number of the treadmill is WLTL211041. The serial number can be found
on a decal attached to the treadmill (see the front
cover of this manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Water Bottle Holder
(Bottle not included)
Console
Handrail
Key/Clip
Storage Latch
FRONT
Upright
Walking Belt
Circuit Breaker
Foot Rails
Power Cord
BACK
Incline Leg
RIGHT SIDE
Rear Roller
Adjustment Bolts
4
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply
wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included allen wrenches
wire cutters
, and needlenose pliers
and your own phillips screwdriver
.
,
To identify small parts, use the PART IDENTIFICATION CHART attached in the center of this manual.
Note: If a part is not in the parts bag, first check to see if it has been pre-assembled.
1. Make sure that the power cord is unplugged.
1
38
With the help of a second person, carefully raise the
Uprights (38) until the treadmill is in the position shown.
Cut the plastic tie (not shown) off the right Upright (38).
2. Insert one of the Extension Legs (15) into the treadmill
as shown. Make sure that the Base Pad (33) is on the
indicated side. Note: It may be helpful to tip the Uprights
(38) in the direction shown by the arrow as you insert
the Extension Leg.
2
38
Attach the Extension Leg (15) with an Extension Leg
Screw (14). Make sure to push on the head of the
Extension Leg Screw while tightening it.
14
Attach the other Extension Leg (15) in the same way.
15
33
5
3. If there are plastic ties in the brackets on the Handrails
(4), remove the plastic ties. Hold one of the Handrails
near the right Upright (38) as shown. Insert the Wire
Harness (53) up through the bracket on the Handrail and
out of the round hole in the side of the Handrail. If necessary, use needlenose pliers to pull the Wire Harness
out of the hole. Be careful not to damage the Wire
Harness.
Insert the brackets on the Handrails (4) into the upper
ends of the Uprights (38).
3
4
Connectors
40
Bracket
40
16
16
38
40
Finger tighten four 1” Bolts (16) with Handrail Washers
(40) into the Uprights (38) and the Handrails (4) as
shown.
4. Set the Console Base (87) on the Handrails (4). Thread
four 3/4” Screws (5) into the Handrails and the Console
Base. After you have started all four Screws, tighten the
Screws until they are snug; do not overtighten the
Screws. Note: It may be helpful to press down on the
top of the Console Base above the Handrails as you
tighten the Screws.
4
53
16
16
38
4
87
4
53
4
See step 3. Firmly tighten, but do not overtighten,
the four 1” Bolts (16).
Plastic Ties
5
5
Insert the Wire Harness (53) through the two indicated
plastic ties on the Console Base (87) and up through the
hole in the Console Base as shown.
5. Hold the Console (11) near the Console Base (87).
Touch the right Handrail (4) to discharge any static.
5
11
A
Next, insert the Wire Harness (53) through the plastic tie
labeled C in the drawing at the right.
Locate the two connectors on the Wire Harness (53).
Plug the wider connector into the connector labeled A in
the drawing at the right (see drawing 5b). The connectors should slide together easily and snap into
place. If they do not, turn the connector on the Wire
Harness and try again. Insert the other connector
through the plastic tie labeled D; plug the connector into
the connector labeled B (see drawing 5c). IF THE CONNECTORS ARE NOT INSERTED PROPERLY, THE
CONSOLE MAY BE DAMAGED WHEN THE POWER
IS TURNED ON.
See drawing 5a. Pull any slack in the Wire Harness (53)
through the two ties. Make sure that the end of the Wire
Harness indicated by the arrow is routed as shown.
Securely tighten the plastic ties around the Wire
Harness. Cut off the end of each plastic tie.
Tie C
87
4
B
53
5a
Tie
Tie
53
5b
53
5c
A
B
53
6
Tie D
6. Set the Console (11) in the Console Base (87). Make sure
that no wires are pinched. Insert as much of the Wire
Harness (53) as possible down into the hole in the right
Handrail (4). Securely tighten the plastic tie nearest to
the right Handrail. Pull any excess Wire Harness
between the plastic ties tight and tighten the other plastic
tie. Cut off the ends of the plastic ties. Cover the Wire
Harness with the Wire Cover (10), and route the Wire
Harness out of the hole in the side of the Wire Cover.
Attach the Wire Cover to the back of the Console Base
with two 3/4” Screws (5). Do not overtighten the Screws.
6
Ties
53
11
5
10
Make sure that no wires are pinched before you
attach the Console (11) to the Console Base (87).
Tighten five 3/4” Screws (5) into the Console Base and
the Console in the locations shown. Note: No 3/4”
Screw goes into the hole indicated by the arrow. Do
not overtighten the Screws.
7. Attach the Storage Latch (66) to the left Upright (38)
with two 3/4” Screws (5).
5
No
Screw
87
5
5
5
4
7
38
66
5
8. Make sure that all parts used in assembly are properly tightened before you use the treadmill. Keep
the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page
13). To protect the floor or carpet, place a mat under the treadmill.
7
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
grounding plug. Plug the power cord into a surge
suppressor, and plug the surge suppressor into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances. Important: The treadmill is not compatible with GFCI-equipped outlets.
Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances being turned on or off. To decrease the possibility of your treadmill being damaged, always use
a surge suppressor with your treadmill (see drawing 1 at the right).
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have
a UL suppressed voltage rating of 400 volts or
less and a minimum surge dissipation of 450
joules. The surge suppressor must be electrically
rated for 120 volts AC and 15 amps. There must be
a monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to
use a properly functioning surge suppressor
could result in damage to the control system of
the treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpectedly, which may result in a fall and serious injury.
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet
box covers are not grounded. Contact a qualified
electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunction or break down, grounding provides a path of
least resistance for electric current to reduce the risk
of electric shock. This product is equipped with a cord
having an equipment-grounding conductor and a
8
DIAGRAM OF THE CONSOLE
Displays
Speed Control
Incline Control
Note: If there is a thin sheet of
plastic on the console, remove it.
Stand on the foot rails of
the treadmill. Find the
clip attached to the key,
and slide the clip onto
the waistband of your
clothes.
CAUTION:
Before operating the
console, read the following precautions.
• Do not stand on the walking belt when turning on the power.
• Always wear the clip (see the drawing at the
right) while operating the treadmill.
Key
Next, insert the key fully into the console. After a
moment, the displays will light. Test the clip by carefully taking a few steps backward until the key is
pulled from the console. If the key is not pulled
from the console, adjust the position of the clip.
• Adjust the speed in small increments to
avoid sudden jumps in speed.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed
water bottle in the water bottle holder.
Follow the steps below to operate the console.
1
Insert the key fully into the console.
A few seconds after the key is inserted, the displays will light.
STEP-BY-STEP CONSOLE OPERATION
Before operating the console, make sure that the
power cord is properly plugged in (see page 8).
Next, locate the circuit breaker near the power cord. Make
sure that the circuit breaker is
in the reset position.
Clip
2
Press the Speed s button to start the walking
belt.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
Reset
9
Calories/Speed
display—This display
shows the approximate
number of calories you
have burned and the
speed of the walking
belt. The display will change from one number to
the other every few seconds, as shown by the
mode indicators.
As you exercise, change the speed of the walking
belt as desired by pressing the Speed buttons.
Each time a button is pressed, the speed setting
will change by 0.1 mph; if a button is held down,
the speed setting will change in increments of 0.5
mph. Note: The console can display speed and
distance in either miles or kilometers (see
CALORIES/SPEED DISPLAY at the right). For
simplicity, all instructions in this section refer
to miles.
Note: The console can
display speed and distance in either miles or
kilometers. To change
the unit of measurement,
hold down the Stop button, insert the key into the console, and continue to
hold the Stop button for a moment. An “E” for
English miles or an “M” for metric kilometers will
appear in the Calories/Speed display. Press the
Speed s button to change the unit of measurement. When the desired unit of measurement is
selected, remove the key and then reinsert it.
To stop the walking belt, press the Stop button.
The Time/Distance display will begin to flash.
Note: During the first few minutes that the treadmill
is used, inspect the alignment of the walking belt,
and align it if necessary (see page 13).
3
Change the incline of the treadmill as desired.
To change the incline of the treadmill, press either
of the Incline buttons until the desired incline level
is reached.
4
To reset the displays, press the Stop button,
remove the key, and then reinsert the key.
Follow your progress with the displays.
Time/Distance
Mode Indicator
display—This display
shows the elapsed time
and the distance that you
have walked or run. The
display will change from
one number to the other
every few seconds, as shown by the mode indicators. When the Stop button is pressed, the display
will flash.
5
When you are finished exercising, remove the
key.
Step onto the foot rails, press the Stop button, and
remove the key from the console. Keep the key in a
secure place.
10
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
1
Before folding the treadmill, unplug the power cord.
CAUTION: You must be able to safely lift 20 kg (45 lbs.)
to raise, lower or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Raise the treadmill until the storage latch
closes over the catch. Make sure that the storage latch
is fully engaged over the catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage position in temperatures above 30° C (85° F).
2
Closed
Storage
Latch
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
storage latch is fully engaged over the catch.
1. Hold the upper ends of the handrails. Place one foot on
one of the front wheels as shown.
2. Tilt the treadmill back until it rolls freely on the front
wheels. Carefully move the treadmill to the desired location. To reduce the risk of injury, use extreme caution
while moving the treadmill. Do not attempt to move
the treadmill over an uneven surface.
3. Place one foot on a front wheel, and carefully lower the
treadmill until it is resting in the storage position.
Base
Front
Wheels
HOW TO LOWER THE TREADMILL FOR USE
1. See drawing 2 above. Hold the upper end of the treadmill with your right hand as shown. Press the storage
latch and hold it. Pivot the treadmill until the frame and foot rail are past the storage latch.
2. See drawing 1. Hold the treadmill firmly with both hands, and lower the treadmill to the floor. Do not drop
the treadmill frame to the floor. CAUTION: To decrease the possibility of injury, bend your legs and
keep your back straight.
11
MAINTENANCE AND TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, call our Customer Service Department at 1-888936-4266, Monday through Friday 8h00 until 18h30 Eastern Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor that meets all of the specifications described on page 8. Important: The treadmill is not
compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
frame near the power cord. If the switch protrudes as shown, the circuit breaker has tripped.
To reset the circuit breaker, wait for five minutes
and then press the switch back in.
c
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see 1. c. above). If
the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Remove the screws from the hood.
Note each hole the screws are removed from.
Carefully remove the hood. Locate the Reed Switch
(13) and the Magnet (63) on the left side of the Pulley
(75). Turn the Pulley until the Magnet is aligned with
the Reed Switch. Make sure that the gap between
the Magnet and the Reed Switch is about 3 mm. If
necessary, loosen the Screw (89), move the Reed
Switch slightly, and then retighten the Screw. Reattach the hood, making sure that the screws are
tightened into the original holes. Run the treadmill for
a few minutes to check for a correct speed reading.
12
a
3 mm
75
28
13
Top
View
63
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may
become damaged. Remove the key and UNPLUG
THE POWER CORD. Using the allen wrench, turn
both rear roller adjustment bolts counterclockwise,
1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each side of the
walking belt 5 to 7 cm off the walking platform. Be
careful to keep the walking belt centered. Plug in the
power cord, insert the key, and run the treadmill for a
few minutes. Repeat until the walking belt is properly
tightened.
b
5–7 cm
Rear Roller
Adjustment Bolts
c. If the walking belt still slows when walked on, please call our Customer Service Department, tollfree.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the allen wrench to
turn the left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right, turn the
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise,
1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each side of the walking belt 5 to 7 cm off the walking platform. Be careful
to keep the walking belt centered. Plug in the power
cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is
properly tightened.
13
a
b
CONDITIONING GUIDELINES
Aerobic Exercise
WARNING:
Before beginning
this or any exercise program, consult your
physician. This is especially important for
individuals over the age of 35 or individuals
with pre-existing health problems.
If your goal is to strengthen your cardiovascular system,
your exercise must be “aerobic.” Aerobic exercise is
activity that requires large amounts of oxygen for prolonged periods of time. This increases the demand on
the heart to pump blood to the muscles, and on the lungs
to oxygenate the blood. For aerobic exercise, adjust the
speed and incline of the treadmill until your heart rate is
near the highest number in your training zone.
The following guidelines will help you to plan your exercise program. For more detailed exercise information,
obtain a reputable book or consult your physician.
HOW TO MEASURE YOUR HEART RATE
To measure your
heart rate, stop exercising and place two
fingers on your wrist
as shown. Take a sixsecond heartbeat
count, and multiply
the result by ten to
find your heart rate.
(A six-second count is used because your heart rate
drops quickly when you stop exercising.) If your heart
rate is too high or too low, adjust the speed or incline of
the treadmill accordingly.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
WORKOUT GUIDELINES
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up
increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.) Breathe regularly and deeply as you exercise—
never hold your breath.
To measure your heart rate during exercise, use the
pulse sensor.
Fat Burning
To burn fat effectively, you must exercise at a relatively low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for energy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the
treadmill until your heart rate is near the lowest number in your training zone.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent postexercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months, you may complete up to five workouts each week if desired. The
key to success is to make exercise a regular and
enjoyable part of your everyday life.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
14
EXERCISE FREQUENCY
between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
ORDERING REPLACEMENT PARTS
To order replacement parts, call toll-free 1-888-936-4266, Monday through Friday 8h00 until 18h30 Eastern Time
(excluding holidays). When ordering parts, please be prepared to give the following information:
• The MODEL NUMBER of the product (WLTL211041)
• The NAME of the product (WESLO® CADENCE 255 DR treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING in the center of this manual)
PLACE
STAMP
HERE
ICON OF CANADA, Inc.
900 de l’Industrie
St-Jérôme, Québec
Canada, J7Y 4B8
15
PART IDENTIFICATION CHART
Remove this chart and use it to identify small parts during assembly. Save
this chart and the EXPLODED DRAWING/PART LIST for future reference.
3/4” Screw (5)–13
1” Bolt (16)–4
Handrail Washer
(40)–4
Extension Leg Screw (14)–2
PART LIST—Model No. WLTL211041
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44*
45
46
47
48
49*
50
51
52
53
54
55
4
6
2
2
15
1
1
1
2
1
1
1
1
2
2
4
4
1
2
1
1
1
1
1
1
1
5
17
1
1
2
7
4
1
1
2
2
1
4
8
2
2
6
2
1
1
1
1
1
1
4
1
1
2
2
Description
Front Endcap Screw
Star Washer
Plastic Tie
Handrail
3/4” Screw
Key/Clip
Hole Plug
Incline Leg
Handrail Endcap
Wire Cover
Console
Console Cover
Reed Switch
Extension Leg Screw
Extension Leg
1” Bolt
Cage Nut
Motor Belt
Motor Tension Bolt
Motor Tension Washer
Tension Star Washer
Motor Pivot Nut
Motor/Pulley/Flywheel/Fan
Pulley/Flywheel/Fan
Motor
Motor Pivot Bolt
8” Cable Tie
Screw
Hood
Hood Shield
Hood Screw (Front)
Isolator Screw
Base Pad
Motor Belly Pan
Controller
Frame Pivot Bolt
Frame Pivot Washer
Upright/Base
Belt Guide Screw
Roller Washer/Handrail Washer
Wheel Bolt
Wheel
Frame Nut/Wheel Nut
Extension Leg Assembly
Circuit Breaker
Grommet
Power Cord
Motor Tension Nut
Console Assembly
Right Foot Rail
Platform Screw
Front Roller Adj. Bolt
Wire Harness
Incline Wheel Bolt
Incline Wheel
Key No. Qty.
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
#
#
#
#
#
#
1
1
2
1
2
1
1
1
2
1
1
1
3
4
1
1
1
1
1
1
10
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
2
1
1
4
1
4
1
1
1
1
1
1
R1104A
Description
5/32” Allen Wrench
Choke
Belt Guide
Console Warning Decal
Isolator
Latch Catch
Frame Spacer (Left)
Magnet
Incline Leg Pivot Bolt
Belly Pan
Storage Latch
Walking Belt
Wire Tie
Wire Tie Clamp
Incline Wire
Walking Platform
Frame Spacer (Right)
Left Foot Rail
Sensor Clip
Front Roller/Pulley
Electronic Screw
Ground Wire
Rear Roller Adj. Bolt
Left Rear Endcap
Upright Grommet
Allen Wrench
Latch Decal
Rear Roller
Frame
Console Lens
Right Front Endcap
Console Base
Motor Shield
Latch Catch Screw
Right Rear Endcap
Left Front Endcap
Incline Nut
Incline Stop Bracket
Incline Motor Bolt (Lower)
Incline Motor Nut
Incline Motor
Circuit Board Bracket
Plastic Stand-off
Circuit Board
Lift Frame Nut
8” White Wire, Pigtail
4” Red Wire, M/F
4” Black Wire, M/F
4” Black Wire, 2F
6” Blue Wire, 2F
User’s Manual
*Includes all parts shown in the box
“#” indicates a non-illustrated part.
94
78
79
43
93
40
19
96
95
78
70
28
40
90
54
84
55
51
47
28
64
32
73
46
100
61
45
30
28
28
7
77
76
51
100
8
83
60
32
82
39
91
5
58
1
29
50
55
64
56
81
32
5
71
65
60
75
28
62 43 63 13
67
54
37
51
36
31
42
27
32
51
74
28
31
86
1
41
44*
68
28
28
39
69
33
31
33
34
72
43
28
58
52
76
40
43
15
28
18
14
19
66
20
16
57
5
40
42
43
21
40
28
41
15
76
48
22
16
76
28
28
28
33
14
26 53
25
76
24
31
33
44*
80
88
16
23*
40
9
38
76
98
40
53
16
4
37
99
9
36
97
5
59
87
49*
17
76
4
35
33
31
5
85
11
5
17
5
5
5
10
6
12
3
5
EXPLODED DRAWING—Model No. WLTL211041
R1104A
LIMITED WARRANTY
ICON OF CANADA, INC., (ICON), warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of one (1) year from the date of purchase. This warranty
extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at
ICON's option, the product through one of its authorized service centers. All repairs for which warranty claims are
made must be pre-authorized by ICON. This warranty does not extend to any product or damage to a product
caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided
by an ICON authorized service center, to products used for commercial or rental purposes, or to products used as
store display models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with
the use or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some provinces do not allow the exclusion or limitation of incidental or consequential damages.
Accordingly, the above limitation may not apply to you. The warranty extended hereunder is in lieu of any and all
other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its
scope and duration to the terms set forth herein. Some provinces do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from province to province
or so specified by the retailer of your equipment.
ICON OF/DU CANADA, INC., 900 de l’Industrie, St. Jerôme, QC J7Y 4B8
™
®
of/du Canada Inc.
PRODUCT WARRANTY REGISTRATION
IMPORTANT: MAIL WITHIN 14 DAYS OF PURCHASE
NAME:
PHONE:
ADDRESS:
POSTCODE:
COUNTY:
MODEL NO.
SERIAL NO.
PURCHASE DATE:
RETAILER ADDRESS:
RETAILER NAME:
1) Primary user(s) of product:
o Male
o Female
o Family
2) Age of primary user:
o 0–24
o 25–34
o 55–64
o 65 and over
o 35–44
o 45–54
3) Annual household income:
o 0–9,999
o 15,000–19,999
o 10,000–14,999
o 20,000+
4) How many times a week do you exercise?
o Less than 3 times o 3 times or more
5) Have you ever purchased an ICON product before?
o Yes
o No
6) Where did you first see or hear about ICON products?
o Magazine
o Friend/relative
o Newspaper Ad
o Store
o Other
7) What was the primary reason for purchasing this ICON product?
o Store Employee
o Television Ads o Colour
o Electronic Features o Magazine Ads o Price
o Product Design
o Product Innovation
o Other Features
Part No. 222436 R1104A
8) Did you consider purchasing fitness equipment from another
manufacturer?
o No
o Yes
What other Manufacturer?
9) Based on your impression of what you have purchased,
would you buy another ICON product?
o Yes
o No
o No Opinion
If not, what other brand name equipment would you purchase?
10) What other type of exercise equipment do you own?
o Bicycle
o Exercise Cycle o Treadmill
o Home Gym
o Weight Bench o Stepper
o Cardio Glide
o Other
11) Which type of magazines do you read regularly?
o Sports
o Fitness
o Motoring
o Business
o Computer
o General
12) Do you wish to be sent further bulletins about ICON products?
o Yes
o No
THANK YOU FOR YOUR TIME
© 2004 ICON IP, Inc.
Printed in USA © 2004 ICON IP, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement