Weslo WLTL29014 User's Manual

Weslo WLTL29014 User's Manual
ModelNo.WLTL29014
SerialNo.
Writetheserialnumberinthe
spaceaboveforfuturereference.
SerialNumberDecal
USER'S MANUAL
QUESTIONS?
If you have questions, or if there
are missing parts, we will guarantee complete satisfaction through
direct assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained technicians on our customer hot line
will provide immediate assistance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.-Fri.,
6 a.m.-6 p.m. MST
CAUTION
Read all precautions and instructions in this manual before using
this equipment, Save this manual for future reference,
ou_websitea
WWW°WeS[O°COm
new products,
prizes,
fitness tips, and much more!
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS .............................................................
BEFORE YOU BEGIN ...................................................................
ASSEMBLY ...........................................................................
OPERATION AND ADJUSTMENT ..........................................................
HOW TO FOLD AND MOVE THE TREADMILL ...............................................
MAINTENANCE AND TROUBLE-SHOOTING
................................................
CONDITIONING GUIDELINES ...........................................................
ORDERING REPLACEMENT PARTS ...............................................
LIMITED WARRANTY ...........................................................
2
4
5
7
10
12
14
Back Cover
Back Cover
Note: A PART LIST and an EXPLODED DRAWING are attached in the center of this manual.
IMPORTANT PRECAUTIONS
A WARN ING:
the following
To reduce the risk of burns, fire, electric shock, or injury to persons, read
important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions,
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage,
place a mat under the treadmill.
4.
Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should not be used by persons
weighing more than 250 pounds.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothing when
using the treadmill. Do not wear loose clothing that could become caught in the treadmill. Athletic support clothes are recommended for both men and women. Always wear
athletic shoes. Never use the treadmill with
bare feet, wearing only stockings, or in sandais.
10. When connecting the power cord (see page 7),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be
on the same circuit. Do not use an extension
cord.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 7. To purchase a surge suppressor, see
your local WESLO dealer or call 1-800-8063651 and order part number 146148.
12. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
13. Keep the power cord and the surge suppressor away from heated surfaces.
14.Nevermovethe walkingbeltwhilethe power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 4 if the treadmill is not working properly.)
15. Never start the treadmill while you are sta nding on the walking belt. Always hold the
handrails while using the treadmill.
16. Using hand weights and not holding the
handrails may compromise your ability to
maintain your balance. Hand weights should
be used only by experienced users.
must be able to safely lift 45 pounds (20 kg) in
order to raise, lower, or move the treadmill.
20. Do not change the incline of the treadmill by
placing objects under the treadmill.
21. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
22. Inspect and tighten all parts of the treadmill
every three months.
23. Never insert or drop any object into any
opening.
24.
17. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
18. Never leave the treadmill unattended while it
is running. Always remove the key and unplug
the power cord when the treadmill is not in
use.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO FOLD
AND MOVE THE TREADMILL on page 10.) You
_
WARN ING:
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures
described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service representative only.
25. This treadmill is intended for in-home use
only. Do not use this treadmill in any commercial, rental, or institutional setting.
Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decal shown below has been placed on your treadmill. If
the decal is missing or illegible, please call our Customer
Service Department, toll-free, to order a free replacement
decal (see ORDERING REPLACEMENT PARTS on the back
cover of this manual). Apply the decal in the location shown.
Note: This decal is shown at 38% of actual size.
BEFORE YOU BEGIN
Thank you for selecting the WESLO ®CADENCE 340
CS treadmill. The CADENCE 340 CS combines
advanced technology with innovative design to let you
enjoy an excellent form of cardiovascular exercise in
the convenience and privacy of your home. And when
you're not exercising, the CADENCE 340 CS can be
folded up, requiring less than half the floor space of
other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our Customer Service Department toll-free
at 1-800-999-3756, Monday through Friday, 6 a.m.
until 6 p.m. Mountain Time (excluding holidays). To
help us assist you, please note the product model
number and serial number before calling. The model
number of the treadmill is WLTL29014. The serial
number can be found on a decal attached to the treadmill (see the front cover of this manual for the location).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
-Speed Control
Water Bottle Holder
(Bottle not included)
Accessory Tray
Console
Key/Clip
Storage LatchFRONT
Uprights
Walking Belt
Foot Rails
Circuit Breaker
BACK
Pin
Rear Roller
Adjustment
Bolts
--Incline
Leg
RIGHT SIDE
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the included allen wrench, assembly
requires a phillips screwdriver
, an adjustable wrench ©_
and scissors _--_.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply
wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Handrail Star
Washer (2)---4
Handrail Washer (80)--4
Latch Screw/Rack
Screw (14)-14
Base Leg Screw (39)-2
Console
Screw (3)=4
1. With the help of a second person, raise the Uprights (38)
to the position shown. Note: During this step and step
2, be careful not to pull on or damage the Wire
Harness (53) in the right Handrail (4).
Insert one of the Base Legs (44) into the right Upright
(38), with the Base Leg Pad (33) in the indicated position.
Using the included Allen Wrench (81), attach the Base
Leg with a Base Leg Screw (39). Attach the other Base
Leg (not shown) to the left Upright in the same way.
Note: A replacement Base Leg Pad (33) may be included.
If a Base Leg Pad becomes worn and needs to be
replaced, use the replacement Base Leg Pad.
81
33
2. Hold the Left Handrail (88) against the left Upright (38) as
shown. (Important: If you are shorter than 5' 8", align
the upper two holes in the Handrail with the holes in
the Upright; if you are 5' 8" or taller, align the lower
two holes.) Attach the Left Handrail with two Handrail
Bolts (1), two Handrail Washers (80), and two Handrail
Star Washers (2) as shown. Do not tighten the Handrail
Bolts yet.
Make sure that at least 6" to 8" of the Wire Harness (53)
is extending from the top of the Right Handrail (4). Feed
the excess Wire Harness into the right Upright (38), and
hold the Right Handrail against the right Upright. Make
sure that both Handrails are at the same height.
Attach the Right Handrail with two Handrail Bolts (1), two
Handrail Washers (80), and two Handrail Star Washers
(2). Do not tighten the Handrail Bolts yet. Be careful
not to pinch the Wire Harness. Remove the tie from the
Wire Harness and the Handrail.
53
38
53
80
3. HoldtheConsoleBase(87)nearthe rightHandrail(4).
Makea loopwiththeindicated
plastictie,andinsertthe
twoWires(53)throughtheloop.Pulloutjustenoughof
theWirestoconnectthemtothetwoconnectors
inthe
ConsoleBase(87).Plugtheredconnector
intothecorresponding
connector
intheConsole
Base.Theconnectors
shouldsnaptogether
withoutbeingforced.Iftheydonot,
rotatetheredconnector
ontheWireandtryagain.Next,
plugtheotherWireintotheotherconnector
onthe
ConsoleBase.Important: Make sure that the Wires (53)
Plastic
Tie
(_
3a
87
are fully inserted. Do not force the connectors together. IF THE CONNECTORS ARE NOT INSERTED PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE
POWER IS TURNED ON. Do not disconnect or connect
the Wires while the treadmill power cord is plugged in.
Refer drawing 3a. Set the Console Base (87) on the
Handrails (4, 88). Thread four Console Screws (3) into
the Handrails and the Console Base. After all four
Plastic
Tie
3
Screws have been started, tighten the Screws until
they are snug; do not overtighten the Screws.
Feed the excess Wire Harness (53) into the upper end
of the right Handrail (4). Pull the plastic tie tight and cut
off the end.
38
16
14
4. Attach the Storage Latch (16) to the left Upright (38)
with two Latch Screws (14).
Refer to step 2. Tighten the four Handrail Bolts (1).
5. Hold a Weight Rack (15) against the right Upright (38) in
the position shown. Loosely thread two Rack Screws
(14) into the bottom holes in the Weight Rack and the
Upright. Next, loosely thread four Rack Screws into the
other four holes. Then, tighten all six Rack Screws.
Set a 3-lb. Weight (not shown) on the bottom hanger on
the Weight Rack (15), a 2-lb. Weight on the middle
hanger, and a l-lb. Weight on the top hanger.
15
14
14
Hanger
Attach the other Weight Rack and Weights to the left
Upright in the same way (not shown).
14
6. Make sure that all parts are tightened before you use the treadmill.
mat under the treadmill.
To protect the floor or carpet, place a
OPERATION AND ADJUSTMENT
THE PERFORMANT
LUBE TM WALKING BELT
Your treadmill features a walking belt coated with
PERFORMANT LUBE TM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking platform. Such substances will deteriorate the walking
belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
DANGER:
connection
Improper
of the equipment-grounding
conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product--if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home's power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances being turned on or off. To decrease the possibility of your treadmill being damaged, always
use a surge suppressor with your treadmill (see
drawing 1 at the right). To purchase a surge suppressor, see your local WESLO dealer or call 1800-806-3651 and order part number 146148.
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have
a UL suppressed voltage rating of 400 volts or
less and a minimum surge dissipation of 450
joules. The surge suppressor must be electrically
rated for 120 volts AC and 15 amps. There must be
a monitoring light on the surge suppressor to indicate whether it is functioning
properly. Failure to
use a properly functioning surge suppressor
could result in damage to the control system of
the treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpectedly, which may result in a fall and serious injury.
This product must be grounded. If it should malfunction or break down, grounding provides a path of
least resistance for electric current to reduce the risk
of electric shock. This product is equipped with a cord
having an equipment-grounding conductor and a
grounding plug. Plug the power cord into a surge
suppressor, and plug the surge suppressor into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances. Important: The treadmill is not compatible with GFCl-equipped outlets.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
_Grounded
_"-I
II
Outlet Box
_
Surge Suppressor
__
Grounded
U_J
Grounding Pin
Outlet
G_ounding
Plug _
Outlet Box
Adapter
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet
box covers are not grounded. Contact a qualified
electrician to determine if the outlet box cover is
grounded before using an adapter.
DIAGRAM OF THE CONSOLE
Monitor Displays
STEP BY STEP
I _,_
[
[
_-s
[
SPEED
TRAINING
1[ HEART A,E1
ZONES
INSTRUCTIONS
TRAINING
ZONES
INSERTKEY
AGE
_ MAXB_/_ ]
ON/RESET
I
MJN_P,_
40
1_s
13o
14_ I
80
90
_03
_
BUTTON
[
CALS
E
F CALS
SPEED
TIME
DISI'ANCE
SETTO DESIREDLEVEL
I
]
FAST
RESET
,)LLJ
Speed
VV
Control _
A
ON
OFF
w
If there is a thin sheet of clear
plastic on the console, remove it.
CAUTION:
Before operating the
console, read the following
precautions.
the negative (-) ends of the batteries touching the
springs. Close the battery cover, push up on the tab,
and then push the tab forward as shown. Be sure that
the tab locks into place.
• Do not stand on the walking belt when turning on the power.
Battery
Cover
• Always wear the clip (see the drawing
above) while operating the treadmill. When
the key is removed from the console, the
walking belt will stop.
• Adjust the speed in small increments.
• The training zones marked around the speed
control are general guidelines only. See
page 14 for more information.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and use only a sealable
water bottle.
BATTERY INSTALLATION
The console requires two "AA" batteries (not included). Alkaline batteries are recommended. To install
batteries, open the battery cover as shown at the right.
Press two batteries into the battery compartment, with
Tab
STEP-BY-STEP
CONSOLE OPERATION
Before operating the console, make sure that the
power cord is properly plugged in. (See HOW TO
PLUG IN THE POWER CORD on page 7.)
Stand on the foot rails of the treadmill. Find the clip
attached to the key, and slide the clip onto the waistband of your clothing. Next, insert the key into the
console. Test the clip by carefully taking a few
steps backward until the key is pulled from the
console. If the key is not pulled from the console,
adjust the position of the clip as needed.
Follow the steps on page 9 to operate the console.
_
Inserting the key will not turn on the displays. The
displays will turn on when the ON/RESET button
is pressed or when the walking belt is started.
Note: If you just installed batteries, the displays
will already be on.
B
eset the speed control and start the walking
belt.
Turn the speed
control to the RESET
position. Note: Each
time the walking
belt is stopped, the
speed control must
be turned to the
If desired, reset the displays by pressing the
ON/RESET button.
B
hen you are finished exercising, stop the
walking belt and remove the key.
Step onto the foot rails, turn the speed control to
the RESET position, and remove the key from the
console. The displays will turn off about six minutes after the key is removed. Note: The displays
will automatically turn off in order to conserve
the batteries any time that the walking belt is
stopped and the ON/RESET button is not
pressed for six minutes.
J
RESET position
before the walking belt can be restarted. Next,
slowly turn the speed control until the walking belt
begins to move at slow speed. Carefully step onto
the walking belt and begin exercising. Change the
speed of the walking belt as desired by turning
the speed control.
During the first few minutes that you use the treadmill, inspect the alignment of the walking belt, and
align the walking belt if necessary (see page 13).
To stop the walking belt, step onto the foot rails
and turn the speed control to the RESET position.
D
• Distance--This mode shows the total number of
miles you have walked or run.
Insert the key fully into the power switch.
Follow your progress with the monitor modes
When the power
is turned on, the
_P"
t
"N
,5u8
console will scan
through five
modes repeatedly.
Flashing mode
arrows will show
which mode is currently displayed. The modes
are described below.
HOW TO CHANGE THE INCLINE OF THE TREADMILL
To vary the intensity of your exercise, the incline of the
treadmill can be changed. There are four incline levels. Before changing the incline, remove the key
and unplug the power cord. Next, fold the treadmill
to the storage position (see HOW TO FOLD THE
TREADMILL FOR STORAGE on page 10).
To change the incline, first remove the incline pin from
the right incline leg as shown below. Adjust the incline
leg to the desired height and fully reinsert the incline
pin. Make sure that the incline pin is in the "locked"
position shown in the inset drawing. Adjust the left
incline leg in the same way. Make sure that both
incline pins are inserted from the direction shown.
Incline
Pin
Incline
Pin
Incline Pin
• Calories (CALS)--This mode shows the approximate number of calories you have burned.
• Fat Calories (F-CALS)--This mode shows the
approximate number of fat calories you have
burned. (See FAT BURNING on page 14.)
• Speed--This
per hour.
mode shows your speed, in miles
• Time--This mode shows the elapsed time. Note:
If you stop exercising for ten seconds or longer,
the time mode will pause.
Right
III
CAUTION: Before using the treadmill, make sure
that both incline pins are fully inserted at the same
height. Do not use the treadmill with the incline
pins removed. After you have adjusted the incline
legs, lower the treadmill (see HOW TO LOWER THE
TREADMILL FOR USE on page 11).
HANDRAILHEIGHTADJUSTMENT
The Handrails (4, 88) can be adjusted to either of two heights.
Before adjusting the Handrails, remove the key and
unplug the power cord.
Remove the four Console Screws (3). While a second person
lifts the Console Base (87), remove the Handrail Bolts (1),
Handrail Washers (80), and Handrail Star Washers (2). Raise
or lower the Handrails (4, 88) to the desired height, being careful not to damage the Wire Harness (53). Reattach the
Handrails with the Handrail Bolts, Handrail Washers, and
Handrail Star Washers. (Important: If you are 5' 8" or taller,
use the lower two holes in the Handrail; if you are shorter
than 5' 8", use the upper two holes. Make sure that both
Handrails are at the same height. Do not tighten the
Handrail Bolts yet. Always attach each Handrail with two
Handrail Bolts.) Reattach the Console Base (87) (see assembly step 3 on page 6). Then, tighten the four Handrail Bolts.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL
FOR STORAGE
Before folding the treadmill, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) in order to raise, lower or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left thumb, press the storage
latch and hold it. Pivot the treadmill until the frame and
foot rail are past the storage latch. Close the storage
latch over the catch. Make sure that the storage latch
is fully engaged over the catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85 ° Fahrenheit.
10
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
storage latch is locked fully over the catch.
1. Remove the weights from the weight racks.
2. Hold the upper ends of the handrails. Place one foot on
one of the wheel as shown.
3. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. To
reduce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
4. Place one foot on the base, and carefully lower the treadmill until it is resting in the storage position.
HOW TO LOWER THE TREADMILL
FOR USE
1. Hold the upper end of the treadmill with your right hand
as shown. Using your left thumb, press the storage latch
and hold it. Pivot the treadmill until the frame and foot
rail are past the storage latch.
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. Do not drop the treadmill frame
to the floor. To decrease the possibility of injury,
bend your legs and keep your back straight.
11
Wheels
MAINTENANCE
AND TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department tollfree at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM:
The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 7). Use only a single-outlet surge suppressor that meets all of the specifications described on page 7. Important: The treadmill is not
compatible with GFCl-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
C.
PROBLEM:
Check the circuit breaker located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the circuit breaker has tripped. To reset
the circuit breaker, wait for five minutes and then
press the switch back in.
C
Tripped
Reset
The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above), tf the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Make sure that the two wires under the console are fully plugged in. (Refer to assembly step 3
on page 6. WARNING: Do not disconnect or connect the wires while the treadmill power
cord is plugged in.)
d. Remove the key from the console. Reinsert the key fully into the console.
e. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM:
The displays of the console do not function properly
SOLUTION: a. Check the batteries in the console. If the batteries need to be replaced, see BATTERY
INSTALLATION on page 8. Most problems are the result of drained batteries.
b.
Remove the screws from the hood, and carefully
remove the hood. Locate the Reed Switch (13) and
the Magnet (63) on the left side of the Pulley (75).
Turn the Pulley until the Magnet is aligned with the
Reed Switch. Make sure that there is a gap of
about 1/8" between the Magnet and the Reed
Switch. If necessary, loosen the Screw (31) and
move the Reed Switch slightly. Retighten the Screw.
Re-attach the hood, and run the treadmill for a few
minutes to check for a correct speed reading.
12
PROBLEM:The
walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 7.
b.
If the walking belt is overtightened, treadmill performance may decrease and the walking belt may
become damaged. Remove the key and UNPLUG
THE POWER CORD. Using the allen wrench, turn
both rear roller bolts counterclockwise 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 2
to 3 inches off the walking platform. Be careful to
keep the walking belt centered. Plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is properly
tightened.
Rear Roller
Adjustment Bolts
c. If the walking belt still slows when walked on, please call our Customer Service Department,
toll-free.
PROBLEM:
The walking belt is off-center or slips when walked on
SOLUTION:
a. If the walking belt is off-center, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the allen wrench to
turn the left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right, turn the
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
b.
If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly
tightened, you should be able to lift each side of the
walking belt 3 to 4 inches off the walking platform.
Be careful to keep the walking belt centered. Plug in
the power cord, insert the key, and carefully walk on
the treadmill for a few minutes. Repeat until the
walking belt is properly tightened.
13
CONDITIONING
GUIDELINES
speed control on the console to FAT BURN to help you
maintain the proper intensity level. (See page 9.)
WARNING: Before
beginning
this or any exercise program, consult your
physician. This is especially important for
individuals over the age of 35 or individuals
with pre-existing health problems.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be "aerobic." Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed of the treadmill until your heart rate is
near the highest number in your training zone. It may
also be helpful to set the speed control on the console
to AEROBIC to help you maintain the proper intensity
level. (See page 9.)
The following guidelines will help you to plan your
exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
i
_
MIN
BPM
MAX
BPM
_
High Performance Athletic Conditioning
If your goal is high performance athletic conditioning,
set the speed control on the console to PERFORMANCE to help you maintain the proper intensity
level. (See page 9.) Note: During the first few weeks
of your exercise program, keep your heart rate near
the low end of your training zone.
]
HOW TO MEASURE YOUR HEART RATE
"o
To measure your
heart rate, stop
exercising and place
two fingers on your
wrist as shown.
Take a six-second
heartbeat count, and
multiply the result by
ten to find your
heart rate. (A six-second count is used because your
heart rate drops quickly when you stop exercising.) If
your heart rate is too high or too low, adjust the speed
or incline of the treadmill accordingly.
)CCJ
To find the proper heart rate for you, first find your age
on the left side of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers to
the right of your age. The three numbers are your
"training zone." The lower two numbers are recommended heart rates for fat burning; the highest number
is the recommended heart rate for aerobic exercise.
USING THE HAND WEIGHTS
The included hand weights let you add upper body
exercise to your workouts. As you walk on the treadmill, hold the l-lb. weights at your sides or press the
weights above your head. To increase the intensity of
your exercise, use the 2-lb. or 3-lb. weights. WARNING:
Use the hand weights only at walking speeds.
Using weights and not holding the handrails may
compromise your ability to maintain your balance.
Exercises using weights should be attempted only
by experienced users.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for energy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed of the treadmill until
your heart rate is near one of the lower two numbers in
your training zone. It may also be helpful to set the
14
WORKOUT
GUIDELINES
zoneforlongerthan20 minutes.)Breatheregularly
anddeeplyas youexercise--never hold your breath.
Each workout should include the following three parts:
A Cool-down
A Warm-up
Finish each workout with 5 to 10 minutes of stretching
to cool down. This will increase the flexibility of your
muscles and will help prevent post-exercise problems.
Start each workout with 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in preparation for exercise.
EXERCISE FREQUENCY
Training Zone Exercise
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months, you may complete up to five workouts each week if desired. The
key to success is to make exercise a regular and
enjoyable part of your everyday life.
After warming up, increase the intensity of your exercise until your pulse is in your training zone for 20 to
60 minutes. (During the first few weeks of your exercise program, do not keep your pulse in your training
SUGGESTED
STRETCHES
The correct form for several basic stretches is shown in the drawings
below. Move slowly as you stretch--never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from your
hips. Allow your back and shoulders to relax as you reach down toward
your toes as far as possible. Hold for 15 counts, then relax. Repeat 3
times. Stretches: Hamstrings, back of knees and back.
2. Hamstring
Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward you
and rest it against the inner thigh of your extended leg. Reach toward
your toes as far as possible. Hold for 15 counts, then relax. Repeat 3
times for both legs. Stretches: Hamstrings, lower back and groin.
3. Calf/Achilles
Stretch
With one leg in front of the other, reach forward and place your hands
against a wall. Keep your back leg straight and your back foot fiat on
the floor. Bend your front leg, lean forward and move your hips toward
the wall. Hold for 15 counts, then relax. Repeat 3 times for both legs. To
cause further stretching of the achilles tendons, bend your back leg as
well. Stretches: Calves, achilles tendons and ankles.
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp one
foot with your other hand. Bring your heel as close to your buttocks as
possible. Hold for 15 counts, then relax. Repeat 3 times for both legs.
Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15 counts,
then relax. Repeat 3 times. Stretches: Quadriceps and hip muscles.
15
4
PART LIST--Model
Key No.
1
2
3
4
5
6
7
8
9
10
11*
12
13
14
15
16
17"
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
Qty.
4
4
4
1
8
1
1
2
1
1
1
2
1
17
2
1
2
1
1
1
1
1
1
1
1
1
5
15
1
1
9
2
4
1
1
2
2
1
2
3
2
2
4
2
1
1
1
No. WLTL29014
Description
Handrail Bolt
Handrail Star Washer
Console Screw
Right Handrail
Console Insert Screw
Key/Clip
Right Frame Guide
Incline Leg
Speed Potentiometer
Speed Control
Console Assembly
Battery Cover
Reed Switch
Rack Screw/Latch Screw
Weight Rack
Storage Latch
Extension Leg Assembly
Motor Belt
Motor Tension Bolt
Motor Tension Washer
Tension Star Washer
Motor Pivot Nut
MotorlPulleylFlywheellFan
Pulley/Flywheel/Fan
Motor
Motor Pivot Bolt
8" Cable Tie
3/4" Screw
Hood
Hood Shield
Small Screw
l-lb. Hand Weight
Base Leg Pad
Motor Belly Pan
Controller
Frame Pivot Bolt
Frame Pivot Washer
Upright Base
Extension Leg Screw
Roller Adj. Washer
Wheel Bolt
Wheel
Incline Nut/Frame Pivot Nut
Base Leg
Circuit Breaker
Grommet
Power Cord
Key No.
R0903A
Qty.
Description
48
1
Motor Tension Nut
49
2
Upright Endcap
50
1
Right Foot Rail
51
4
Platform Screw
52
1
Front Roller Adj. Bolt
53
1
Wire Harness
54
6
Isolator Screw
55
2
Front isolator
56
2
2-lb. Hand Weight
57
1
Choke
58
2
Belt Guide
59
2
3-lb. Hand Weight
60
2
Isolator
61
2
Wheel Nut
62
1
Frame Spacer (Left)
63
1
Magnet
64
2
Incline Pin
65
2
Endcap Washer
66
1
Catch
67
1
Walking Belt
68
3
Wire Tie
69
4
Wire Tie Clamp
70
1
Frame Spacer (Right)
71
1
Walking Platform
72
2
Endcap
73
2
Isolator Spacer
74
1
Sensor Clip
75
1
Front Roller/Pulley
76
4
Electronic Screw
77
1
Ground Wire
78
2
Rear Roller Adj. Bolt
79
1
Rear Endcap
80
4
Handrail Washer
81
1
Allen Wrench
82
1
Latch Decal
83
1
Rear Roller
84
1
Frame
85
2
Rear Platform Screw
86
1
Left Foot Rail
87
1
Console Base
88
1
Left Handrail
#
1
4" Red Wire, Male/Female
#
1
4" White Wire, Male/Female
#
1
4" Blue Wire, Male/Female
#
1
User's Manual
* Includes all parts shown in the box
Note: "#" indicates a non-illustrated part.
Specifications are subject to change without notice. See the back cover of the user's manual for information
about ordering replacement parts.
I'll
X
I"
0
18
I5
49
. \
,,
/-/
28
i
36
30
37
28
i
i
[
28
0
1
50
5
67
53
71
Z
0
4
\<
38
:
q
35
73
I"
3
5'8
57
\
0
--...
---..... "---\
23
' 4O
78
' h
,
82
®
65
81
_
77
_
69
;U
o
_3
o
GO
3>
ORDERING
REPLACEMENT
PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give the following information when calling:
• The MODEL NUMBER of the product (WLTL29014)
• The NAME of the product (WESLO CADENCE <_340 CS treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION
DRAWING in the center of this manual)
of the desired part(s) (see the PART LIST and the EXPLODED
WESLO is a registered trademark of ICON Health & Fitness, Inc.
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse,
improper or abnormal usage or repairs not provided by an ICON authorized service center; products used
for commercial or rental purposes; or products used as store display models. No other warranty beyond
that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 204542 R0903A
Printed in USA © 2003 iCON Health & Fitness, inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement